DF300AP/250AP DF300AP DF250AP

Transcription

1 PARTS CATALOGUE DF300AP/250AP DF300AP DF250AP OUTBOARD MOTOR E ST EDITION

2 PREFACE When it becomes necessary to replace parts on SUZUKI OUTBOARD MOTORS, always use SUZUKI GENUINE PARTS which have passed a strict inspection which guarantees quality and performance. This parts catalogue covers the list of all service parts for SUZUKI DF250A/300A production start INSTRUCTIONS FOR QUOTING THE CATALOGUE 1. DIMENSIONS Dimensions of the parts in this catalogue are indicated in unit millimeters. 2. ABBREVIATIONS Abbreviations used in this catalogue are as follows: AR : As required NT : Number of teeth ASSY : Assembly OPT : Optional E.NO. : Engine number OS : Over size F.NO. : Frame number STD : Standard D : Diameter of material T : Thickness ID : Inside diameter US : Under size OD : Outside diameter W : Width L : Length W/ : With LH(PORT) : Left hand side X,XX : Transom type RH(STBD) : Right hand side SUS : Stainless steel ~ : Up to E.NO.30002F PTT : Power trim and tilt ~ : From E.NO.30002F x 34 x Figures in the description column show the dimensions of parts. ID OD T(or W,L) 3. INNER PARTS OF ASSEMBLY Part name with a dot (.) in front as shown in the description column indicates the component of the assembly also available individually. 4. MODIFICATION NOTICE A parts bulletin will be sent to you on all occasions when changes in parts occur, including interchangeable modifications between new parts and old ones. 5. NOTE 5-1. There are some different parts from those of production models among spare parts for the administrative reasons and common use of them with other models In respect of rubber hoses and vinyl tubes, please be sure to use them by cutting off according to the length mentioned on parts catalogue or what is actually required on the vehicle Note that the drawings on the illustration page are for ready reference of spare parts number, not to be used as an assembly manual. When assembling, use "SUZUKI SERVICE MANUAL". 6. MODEL NAME AND ENGINE NUMBER MODEL DESTINATION TYPE TRANSOM ENGINE No. DF250AP E P X,XX 25003P ~ DF300AP E P X,XX 30002P ~ (Parts No.) : indicates that the parts number was changed to and the new parts are interchangeable with the former ones but the former ones are not interchangeable with new ones (Parts No.) : indicates that the former and new parts are interchangeable with each other and both are usable. DF250A/300A E DF250A/300A E

3 PREFACE Quand il devient nécessarie de remplacer des pièces sur SUZUKI MOTEURS HORSBOARD toujours utiliser les PIECES D'ORIGINE SUZUKI qui ont été soumises à des contriles de qualité sévères leur garantissant qualité et performance impeccables. Ce catalogue de pièces détachées couvre la liste de toutes les pièces de rechange pour SUZUKI DF250A/300A production start INSTRUCTIONS POUR UTILISER LE CATALOGUE 1. DIMENSIONS Les dimensions des pièces dans ce catalogue sont indiquées en unités de millimètres. 2. ABREVIATIONS Les abréviations utilisées dans ce catalogue sont les suivantes: AR : Comme requis NT : Nombre de dents ASSY : Assemblage OPT : Sur option E.NO. : Numéro du moteur OS : Sur-dimensionné F.NO. : Numéro du chfssis T : Epaisseur ID : Diamètre intérieur US : Sous-dimensionné OD : Diamètre extérieur W : Largeur L : Longueur LH(PORT) : Côté gauche RH(STBD) : Côte droit ~ : Jusqu'à E.NO.30002F ~ : Depuis E.NO.30002F x 34 x Les chiffres dans la colonne remarques montrent les dimensions ID OD T(or W,L) des pieces comme suit. 3. PIECES INTERNES DE L'ASSEMBLAGE Les numéros de pièces qui comportent un point (.) avant la désignation de pièce détachée indique la pièce interne se rapportant à l'assemblage. 4. AVIS DE MODIFICATION Un bulletin de pièces détachées vous sera envoyé à tout moment opportun quand des changements de pièces ont lieu, y compris les modifications de pièces interchangeables entre les nouvelles et anciennes pièces. 5. A NOTER 5-1. II existe certaines pièces différentes de celles de rechange pour les modèles de production vu des rainsons administratives et dont l'usage est commun avec celles d'autres modèles Concernant les durites en caoutchouc et les tuyaux en vinyle, ne pas manquer de les couper à la bonne longueur comme indiqué dans le catalogue des pièces détachées ou selon ce qui est utile pour le véhicule affecté Noter que les dessins à la page d'illustration servent à titre de référence pour les numéros de pièces détachées, et non pas comme référence pour l'assemblage. Pour cette dernière opération, se reporter au "MANUEL D'ENTRETIEN SUZUKI". 6. NOM DU MODELE / NUMERO DE SERIE DU MOTEUR HOUTEUR DE MODELE DESTINATION TYPE BARRE D'ARCASSE N o DELA MOTEUR DF250AP E P X,XX 25003P ~ DF300AP E P X,XX 30002P ~ (N o de pieces) : indique que le numéro des pièces a été ehangé en et que les nouvelles pièces sont interchangeables avec les anciennes, mais que celles-cine sont pas interchangeables avec les nouvelles (N o de pieces) : indique que les anciennes et nouvelles pièces sont interchangeables les unes avec les autres et sont utilisables chacune. DF250A/300A E DF250A/300A E

4 MILLIMETER INCH CONVERSION CHART TABLEAU DE CONVERSION DE MILLIMETRES POUCES How to read Mode de lecture millimeters equal inc 23 millimètres égalent pouce Contents are subject to change without notice or obligation. Les matières traitées sont susceptibles d'être modifiées sans préavis obligation de notre part.

5 -1-

6 -2-

7 -3-

8 -4-

9 -5-

10 -6-

11 FIG.1 (1-B-2) CYLINDER HEAD J03 HEAD ASSY, CYLINDER STBD J00.BOLT, CAM SHAFT HOUSING PIN (8X11) BOLT J03 HEAD ASSY, CYLINDER PORT J00.BOLT, CAM SHAFT HOUSING PIN (8X11) BOLT J01 PLUG J10 GASKET, CYL HEAD STBD J10 GASKET, CYL HEAD PORT GASKET (16X22X0.8) J00 COVER, PROTECTION ANODE O RING (D:1.9,ID:21.8) J00 ANODE, PROTECTION BOLT (6X14) BOLT BOLT BOLT PIN (14X11.4X23) J01 COVER, CYL HEAD STBD J01 COVER, CYLINDER HEAD PORT J00 PLATE, BREATHER STBD J00 PLATE, BREATHER PORT J00 GASKET, CYL HEAD COVER STBD J00 GASKET, CYL HEAD COVER PORT PIN (8X11) A SCREW BOLT BOLT J00 CAP, OIL FILLER O RING (D:3.1,ID:26.4) SPARK PLUG (NGK, BKR6E) J00 HOOK, ENGINE 2

12 FIG.1 (1-B-3) CYLINDER HEAD BOLT J GUIDE, VALVE (OS:0.5) 24 OPT J00 HOOK, ENGINE 1 OPT

13 FIG.2 (1-B-4) CYLINDER BLOCK J00 HOOK, ENGINE FRONT BOLT J30 BLOCK SET, CYLINDER J00.PLUG, OIL VENTURI J10.BOLT, CRANKCASE J10.BOLT, CRANKCASE STUD J00.BOLT, CYLINDER HEAD FA0.GASKET, M26 PLUG PLUG (26X11) WASHER (18.5X28X2.6) PLUG (18X8) NUT PIN (10.4X13X16) J00.VALVE, PISTON JET O RING (D:1.3,ID:9.8) O RING (D:1.9,ID:9.8) A.BOLT A.BOLT J00.JET, PISTON COOLING O RING (D:1.9,ID:5.7) PLUG J01 COVER, CRANKCASE WTR JKT J00 GASKET, CRANKCASE WTR JKT COV BOLT J00 COVER, OIL GALLERY J00 PLATE, OIL GALLERY J00 GASKET, OIL GALLERY A BOLT BOLT J00 FILTER ASSY, OIL 1

14 FIG.3 (1-B-5) RING GEAR COVER J02 COVER, RING GEAR J00.HOSE, BREATHER J00.UNION, BREATHER J00.PLATE, RING GEAR COVER J00.ARRESTER, FLAME J00.SILENCER, UPPER COVER CLIP BOLT BOLT J00.SCREW J00 BRACE, RING GEAR COVER J10 GUARD, AIR DUCT STBD J10 GUARD, AIR DUCT PORT BOLT BOLT BOLT BOLT E32 LABEL, MAG COVER E10 LABEL (S.I.G.P) J00 LABEL, CLEARANCE J00 LABEL, OIL 1

15 FIG.4 (1-B-6) CRANKSHAFT J00-0B0 PISTON J00 RING SET, PISTON F00 PIN, PISTON CIRCLIP J00 CONNROD ASSY A0 BEARING SET, CONNROD (GREEN) BEARING SET, CONNROD (US:0.25) 6 OPT J00 CRANKSHAFT J00-0A0 BEARING SET, CRANKSHAFT 4 (BLACK) J00-0B0 BEARING SET, CRANKSHAFT (NON) J00-0C0 BEARING SET, CRANKSHAFT 4 (YELLOW) J00-0D0 BEARING SET, CRANKSHAFT (BULE) J00-0E0 BEARING SET, CRANKSHAFT (PINK) AA BEARING SET, CRANKSHAFT 4 OPT (RED/BLACK) US: BA BEARING SET, CRANKSHAFT (RED) 4 OPT US: CA BEARING SET, CRANKSHAFT 4 OPT (RED/YELLOW) US: DA BEARING SET, CRANKSHAFT 4 OPT (RED/BLUE) US: EA BEARING SET, CRANKSHAFT 4 OPT (RED/PINK) US: BEARING SET, CRANK THRUST BEARING SET, CRANK THRUST 1 OPT OS: J00 GEAR, DRIVE (NT:32) WASHER (10.5X50X3.2) A BOLT OIL SEAL (91X109X10) J PISTON SET (OS:0.50) 6 OPT J RING SET, PISTON (OS:0.50) 6 OPT

16 FIG.5 (1-B-7) TIMING CHAIN J00 GEAR, DRIVEN (NT:40) BEARING (40X80X18) 1 LOWER BEARING (40X80X18) 1 UPPER OIL SEAL (32X47X6) J00 HOLDER, DRIVEN GEAR O RING (D:5.7,ID:69.6) A BOLT J00 CHAIN, TIMING 1ST J00 CHAIN, TIMING 2ND J00 BASE, TIMING CHAIN GUIDE NO J00 GASKET, GUIDE BASE PIN A BOLT J00 SHOE, TIMING CHAIN UPPER J00 SHOE, TIMING CHAIN LOWER J00 GUIDE, TIMING CHAIN NO A BOLT J00 TENSIONER ASSY, TIMING CHAIN G00.PAD, TIMING CHAIN TENSIONER J00 SPACER, TIMING CHAIN TENSIONER A BOLT J01 ADJUSTER ASSY, TENSIONER J00 TENSIONER ASSY, STBD J00 TENSIONER ASSY, PORT A BOLT A BOLT 4

17 FIG.6 (1-B-8) CAMSHAFT J10 CAMSHAFT, INTAKE STBD J10 CAMSHAFT, INTAKE PORT J10 CAMSHAFT, EXH STBD J20 CAMSHAFT, EXH PORT J00 SPROCKET ASSY, CAM TIMING 2 (NT:22/32) J00 SPROCKET, EXH CAMSHAFT (NT:22) J00 BOLT, INTAKE CAMSHAFT J00 BOLT, CAMSHAFT EXHAUST PIN (5X12) PIN (5X18) J00 VALVE, OIL CONTROL J00 GASKET, VALVE BOLT J00 TAPPET J SHIM, TAPPET (T:2.175) AR J SHIM, TAPPET (T:2.200) AR J SHIM, TAPPET (T:2.225) AR J SHIM, TAPPET (T:2.250) AR J SHIM, TAPPET (T:2.275) AR J SHIM, TAPPET (T:2.300) AR J SHIM, TAPPET (T:2.325) AR J SHIM, TAPPET (T:2.350) AR J SHIM, TAPPET (T:2.375) AR J SHIM, TAPPET (T:2.400) AR J SHIM, TAPPET (T:2.425) AR J SHIM, TAPPET (T:2.450) AR J SHIM, TAPPET (T:2.475) AR J SHIM, TAPPET (T:2.500) AR J SHIM, TAPPET (T:2.525) AR J SHIM, TAPPET (T:2.550) AR J SHIM, TAPPET (T:2.575) AR J SHIM, TAPPET (T:2.600) AR J SHIM, TAPPET (T:2.625) AR

18 FIG.6 (1-B-9) CAMSHAFT J SHIM, TAPPET (T:2.650) AR J SHIM, TAPPET (T:2.675) AR J SHIM, TAPPET (T:2.700) AR J SHIM, TAPPET (T:2.725) AR J SHIM, TAPPET (T:2.750) AR J SHIM, TAPPET (T:2.775) AR J SHIM, TAPPET (T:2.800) AR J SHIM, TAPPET (T:2.825) AR J SHIM, TAPPET (T:2.850) AR J SHIM, TAPPET (T:2.875) AR J SHIM, TAPPET (T:2.900) AR J SHIM, TAPPET (T:2.925) AR J SHIM, TAPPET (T:2.950) AR J SHIM, TAPPET (T:2.975) AR J SHIM, TAPPET (T:3.000) AR J00 VALVE, INTAKE J10 VALVE, EXHAUST J10 SPRING, VALVE G00 RETAINER, VALVE SPRING COTTER, VALVE G10 SEAT, VALVE SPRING OIL SEAL (5.5X11.5X9.3) 24

19 FIG.7 (1-B-10) INTAKE MANIFOLD J10 MANIFOLD, INTAKE J00 GASKET, INTAKE MANIFOLD STUD BOLT BOLT (8X65) NUT WASHER (8.2X23X3.2) 8

20 FIG.8 (1-B-11) EXHAUST COVER J01 COVER, EXHAUST STBD J01 COVER, EXHAUST PORT J00 GASKET, EXHAUST COVER STBD J00 GASKET, EXHAUST COVER PORT J00 COVER, PROTECTION ANODE J00 ANODE, PROTECTION BOLT (6X14) O RING (D:1.9,ID:21.8) BOLT BOLT 23

21 FIG.9 (1-B-12) FUEL PUMP / FUEL VAPOR SEPARATOR PUMP ASSY, FUEL (L) J10 FILTER, FUEL (L) J10.CAP, FILTER J10.SEAL, NO J10.FILTER ASSY, FUEL J10.CASE ASSY, FILTER J00 COVER, FUEL FILTER J20 HOSE, FUEL (H) J00 CLAMP, FUEL FILTER HOSE (7.5X13.5X600) 1 L:600-> J00 FILTER, FUEL (EPI) CUSHION J00 UNION, FUEL HOSE (H) J00 UNION, 3 WAY WASHER J00 COOLER, FUEL GASKET (11.8X22X1.2) UNION UNION J00 SEPARATOR ASSY, FUEL VAPOR J00.VALVE ASSY, NEEDLE J00.GASKET, SEPARATOR J00.FLOAT ASSY J00.PUMP ASSY, FUEL (H) J00.BUSH, FUEL PUMP J00.SPACER, FUEL PUMP J00.FILTER, FUEL PUMP E00.PIN, FLOAT B.SCREW SCREW J00.REGULATOR, FUEL PRESSURE E00.SCREW J00.SCREW CUSHION 3

22 FIG.9 (1-B-13) FUEL PUMP / FUEL VAPOR SEPARATOR J00 BOLT, COOLER BRACKET HOSE (7.5X13.5X600) 1 L:600-> CLIP (ID:11.5) J20 HOSE, FUEL (L) J00 CLIP J00 CLIP J00 BRACKET, FUEL COOLER BOLT J20 HOSE, FUEL (H) J20 HOSE, FUEL (H) J00 BRACKET, FUEL FILTER BOLT J00 FILTER, FUEL (L) HOSE (7.5X13.5X600) 1 L:600-> J20 HOSE, FUEL (H) BOLT J00 BRACKET, CHECK VALVE J00 VALVE, CHECK J20 HOSE, FUEL (L) E10 SCREW, DRAIN J00 HOSE, DRAIN B SCREW CLIP JC0 PROTECTOR, EVAP HOSE (L:450) JC0 PROTECTOR, EVAP HOSE (L:450) 1 L:450-> CLAMP WASHER (6.5X18X1.6) WASHER BOLT J00 BRACKET, VAPOR SEPARATOR BOLT WASHER BOLT G10 VALVE ASSY, EVAP PURGE 1

23 FIG.9 (1-B-14) FUEL PUMP / FUEL VAPOR SEPARATOR J00 BRACKET, PURGE VALVE BOLT NUT HOSE (5X8.2X600) 1 L:600-> B HOSE (5X8.2X2000) 1 L:2000->810

24 FIG.10 (1-B-15) FUEL INJECTOR J01 HOSE, FUEL (3WAY TO DLVY PIPE) J00 INJECTOR ASSY, FUEL G00.O RING B00 INSULATOR, DELIVERY PIPE J00 PIPE, DELIVERY J01 HOSE, FUEL (DLVY TO DLVY) J00 GASKET, DELIVERY PIPE EA0 UNION, DELIVERY PIPE J00 UNION, DELIVERY PIPE J00 PROTECTOR, FUEL HOSE (L:340) PLUG (14X14) CUSHION UNION CLIP CLAMP CLAMP CLAMP BOLT J21 HOSE, FUEL (PUMP TO FILTER) CLIP CLIP J00 GUIDE, FUEL HOSE BOLT 2

25 FIG.11 (1-C-2) WATER PUMP J01 CASE, WATER PUMP J02 SLEEVE, CASE J00 SEALING, CASE J00 IMPELLER, WATER PUMP J01 PANEL, PUMP CASE UNDER J00 GASKET, PUMP CASE PANEL J00 PANEL, WATER PUMP NO J03 TUBE, WATER (UL) 1 W/TRANSOM(X) J13 TUBE, WATER (XX) 1 W/TRANSOM(XX) J00 BUSH, WATER TUBE UPPER J00 BUSH, WATER TUBE LOWER J00 BUSH, WATER PUMP CASE J00 SPACER, WATER TUBE L00 FILTER, WATER PORT SIDE L00 FILTER, WATER STBD SIDE J00 BOLT, PUMP CASE PANEL BOLT (8X45) SCREW (4X18) PIN (6X12) KEY J01 WATER PUMP REPAIR KIT 1 OPT J00.SEALING, CASE 1 OPT J00.IMPELLER, WATER PUMP 1 OPT J01.PANEL, PUMP CASE UNDER 1 OPT J00.GASKET, PUMP CASE PANEL 1 OPT J00.PANEL, WATER PUMP NO.2 1 OPT KEY 1 OPT

26 FIG.12 (1-C-3) THERMOSTAT J00 HOSE, WATER RETURN STBD J00 HOSE, WATER RETURN PORT J00 PLATE, CYL BLOCK WTR JKT J00 GASKET, CYL BLOCK PLATE J00 PIPE, OUTLET J00 GASKET, OUTLET PIPE J00-0EP COVER, WATER PRESS VALVE 1 (BLACK) E01 VALVE, WATER PRESSURE J20 THERMOSTAT (50sC) J10 THERMOSTAT (71sC) 1 OPT J00 COVER, THERMOSTAT J00 3 WAY, WATER HOSE J00 HOSE (3 WAY TO E/H COV) BOLT (6X25) O RING (D:3.1,ID:26.4) CUSHION HOSE (5X9X600) 1 L:600-> HOSE (5X9X600) 1 L:600-> HOSE (5X9X600) 1 L:600-> HOSE (5X9X600) 1 L:600-> HOSE (5X9X600) 1 L:600-> HOSE (5X9X600) HOSE (5X9X600) B HOSE (5X9X2000) 1 L:2000-> B HOSE (5X9X2000) 1 L:2000-> BOLT JOINT, 3 WAY CLIP CLIP CLIP CLAMP CLIP (ID:20) CLIP 1

27 FIG.12 (1-C-4) THERMOSTAT BOLT BOLT BOLT J00 HOLDER, WATER HOSE CLIP J01 HOSE, WATER FLUSH CLIP (ID:23) CLIP (ID:16) J10 BRACKET, HOSE CLAMP 1

28 FIG.13 (1-C-5) THROTTLE BODY J00 HOSE, PCV B00 SEAL, PCV VALVE J01 COLLECTOR ASSY J00.SPACER, COLLECTOR J01.COVER, COLLECTOR J00..MARK, EMBLEM V6 (4.0L) J00.GASKET, COLLECTOR COVER J00.FUNNEL, COLLECTOR H00.SENSOR, MAP O RING (D:1.3,ID:9.8) BOLT BOLT SCREW PIN J00 BRACKET, COLLECTOR J00 GASKET, COLLECTOR J00 BODY ASSY, THROTTLE J10 GASKET, THROTTLE BODY J00 DAMPER, THROTTLE BODY J00 GASKET, THROTTLE BODY J00 GROMMET, THROTTLE BODY CLIP 2

29 FIG.13 (1-C-6) THROTTLE BODY J00 VALVE, PCV BOLT (8X250) GROMMET CLAMP CLAMP BOLT BOLT BOLT BOLT PIN NUT NUT WASHER (8.2X23X3.2) 2

30 FIG.14 (1-C-7) OIL PUMP J11 SPROCKET, OIL PUMP DRIVE 1 (NT:32) J10 SPROCKET, OIL PUMP DRIVEN 1 (NT:18) J02 PUMP ASSY, OIL J00 STRAINER, OIL PUMP J00 CHAIN, OIL PUMP DRIVE J00 TENSIONER, OIL PUMP CHAIN J00 SPRING, OIL PUMP TENSIONER J01 BOLT, OIL PUMP TENSIONER SHIM (12X20X0.5) O RING (D:2.4,ID:21.8) A BOLT A BOLT A BOLT A BOLT BEARING 1

31 FIG.15 (1-C-8) OIL PAN J00-0EP COVER, PROTECTION ANODE 1 (BLACK) J00 ANODE, PROTECTION J10 ANODE (MAGNESIUM) 1 OPT J30 BOLT, ANODE COVER BOLT (6X14) O RING (D:1.9,ID:21.8) J00 GASKET, OIL PAN J02-0EP PAN, OIL (BLACK) J10 UNION, OIL PAN J00-0EP PIPE, EXHAUST (BLACK) J01 SEAL, EXHAUST TUBE J00 TUBE, EXHAUST J00 GASKET, EXHAUST TUBE J00 BOLT, EXHAUST PIPE J00 PIPE, EXHAUST RELEASE GASKET (12.5X20X2.5) PLUG (12X18.65) PIN (8X12) PIN (8X12) A BOLT BOLT (8X40) BOLT (10X50) BOLT (10X195) J00 BOLT, SPEEDOMETER HOSE CLAMP J10 CLAMP, SPEEDOMETER HOSE J00 GAUGE, OIL LEVEL J00 GUIDE, OIL LEVEL GAUGE O RING (D:2.1,ID:8.8) BOLT 1

32 FIG.16 (1-C-9) CLUTCH SHAFT J00 LEVER, CLUTCH J00 BUSH, CLUTCH LEVER J00 HOLDER, CLUTCH LEVER WASHER (10X20X3) J00 SHAFT, CLUTCH J00 ARM, CLUTCH SHAFT J00 ROD, CLUTCH (UL) J00 LINK, CLUTCH LEVER COVER, CLUTCH ROD WASHER (6.5X15X1.5) PIN SPRING PIN (10.2X10) PLUG (12X9) BALL BEARING (17X35X8) OIL SEAL (18X30X8) BUSH BUSH E RING SPRING BOLT SCREW CIRCLIP J00 LINK, CLUTCH LEVER NO J01 CONNECTOR, REMOCON CABLE E00 NUT, REMOCON CABLE WASHER (7X12X1) CLIP J10 HOLDER, CLUTCH LEVER BOLT 2

33 FIG.17 (1-C-10) CLUTCH ROD L00 ROD, SHIFT DRIVE (X) 1 W/TRANSOM(X) L10 ROD, SHIFT DRIVE (XX) 1 W/TRANSOM(XX) L00 YOKE, SHIFTER J00 MAGNET, GEAR CASE SPRING PIN (3X20) L00-0EP HOUSING, SHIFT ROD GUIDE 1 (BLACK) J00 COVER, SFT GUIDE HSG OIL SEAL OIL SEAL (10X22X8) L00 SLIDER, SHIFT HORIZONTAL J00 BOLT, SHIFT ROD HOUSING WASHER (10.5X19X2) L00 GEAR, SHIFT ROD (NT:13) L00 HOUSING, MAGNET E RING L00 SEALING, SHIFT ROD GUIDE HSG L00 HOUSING, SHIFT SLIDER L00 FILTER, WATER PORT FRONT SIDE L00 FILTER, WATER STBD FRONT SIDE J00 ANODE, PROTECTION BOLT BOLT (6X14) PIN (7.4X9X10) SCREW (4X18) 1

34 FIG.18 (1-C-11) TRANSMISSION L10 SHAFT, DRIVE (X) 1 W/TRANSOM(X) L20 SHAFT, DRIVE (XX) 1 W/TRANSOM(XX) L00 COLLAR, DRIVE SHAFT J00 SPACER, DRIVE SHAFT BEARING NUT BEARING (32X66X49) L01 SET GEAR SHIM (T:0.45) SHIM (T:0.5) SHIM (T:0.55) SHIM (T:0.6) SHIM (T:0.65) SHIM (T:0.7) SHIM (T:0.75) SHIM (T:0.8) SHIM (T:0.85) SHIM (T:0.9) NUT WASHER SPACER (32.4X40X3) 1 REV GEAR SHIM (T:0.5) 1 REV GEAR SHIM (T:0.55) 1 REV GEAR SHIM (T:0.6) 1 REV GEAR SHIM (T:0.65) 1 REV GEAR SHIM (T:0.7) 1 REV GEAR SHIM (T:0.75) 1 REV GEAR SHIM (T:0.8) 1 REV GEAR SHIM (T:0.85) 1 REV GEAR SHIM (T:0.9) 1 REV GEAR SHIM (T:0.95) 1 REV GEAR WASHER (60X72X3) 1 FWD GEAR WASHER (50X58X3) 1 REV GEAR SHIM (T:0.5) 1 REV GEAR SHIM (T:0.55) 1 REV GEAR

35 FIG.18 (1-C-12) TRANSMISSION SHIM (T:0.6) 1 REV GEAR SHIM (T:0.65) 1 REV GEAR SHIM (T:0.7) 1 REV GEAR SHIM (T:0.75) 1 REV GEAR SHIM (T:0.8) 1 REV GEAR SHIM (T:0.85) 1 REV GEAR SHIM (T:0.9) 1 REV GEAR SHIM (T:0.95) 1 REV GEAR SHIM (T:0.5) 1 FWD GEAR SHIM (T:0.55) 1 FWD GEAR SHIM (T:0.6) 1 FWD GEAR SHIM (T:0.65) 1 FWD GEAR SHIM (T:0.7) 1 FWD GEAR SHIM (T:0.75) 1 FWD GEAR SHIM (T:0.8) 1 FWD GEAR SHIM (T:0.85) 1 FWD GEAR SHIM (T:0.9) 1 FWD GEAR SHIM (T:0.95) 1 FWD GEAR BEARING (30X72X28.75) L00 SHAFT, PROPELLER L00 SHIFTER, CLUTCH DOG PIN (8X55) L00 PIN, CONNECTOR SPRING L00 SPRING, DETENT BALL BALL L00-0EP HOUSING, PROP SFT BRG (BLACK) L00.WASHER, REVERSE GEAR THRUST BEARING (30X40X25) BEARING (72X90X34) O RING (D:3,ID:109) OIL SEAL (30X45X6) J01 HOUSING, DRIVE SHAFT BRG 1

36 FIG.18 (1-C-13) TRANSMISSION O RING (D:3.1,ID:65.4) OIL SEAL (24X40X7) L00 SPACER, FORWARD THRUST BEARING (32X58X17) CIRCLIP A CIRCLIP L00 STOPPER, PROP SFT BRG HSG L00 WASHER., PROP SFT BRG HSG NO L00 WASHER., PROP SFT BRG HSG NO L00 SEAL, PROP SFT BRG HSG L00 BUSH, STOPPER O RING (D:1.8,ID:117.6) BEARING (78.26X105X5.45) 1 REVERSE BEARING (83.26X110X5.45) 1 FORWARD

37 FIG.19 (1-C-14) STARTING MOTOR J01 STARTING MOTOR J01.BRUSH SET, PLUS J00.SPRING J00.CASE, GEAR J00.PLATE, CENTER J00.BRACKET, PLANET GEAR J00.COVER KIT, DUST J01.HOLDER, BRUSH J00.LEVER, SHIFT J00.SWITCH, MAGNET J00.ARMATURE J00.PINION J00.SHAFT, PINION J00.INTERNAL GEAR J00.GEAR, PLANETARY J01.WASHER SET J00.TERMINAL J00.CAP, TERMINAL J00.COVER ASSY, REAR J00 BAND, STARTING MOTOR J10 DAMPER, LOWER J00 LEAD WIRE BOLT 2 LOWER BOLT 2 UPPER

38 FIG.20 (1-C-15) MAGNETO J01 FLYWHEEL BOLT (12X26) PIN (6X12) J00 COIL, BATTERY CHARGING J00 HOLDER, STATOR CONNECTING BOLT L00 COIL, IGNITION TIMING BOLT (5X10) J00 SENSOR, CAM POSITION F00.O RING BOLT BOLT (6X35) CLAMP BOLT 2

39 FIG.21 (1-D-2) RECTIFIER / IGNITION COIL J01 RECTIFIER & REGULATOR J00 O RING, RECTIFIER & REGULATOR J01 HOLDER, ELECTRIC PARTS WASHER (6.5X24X1.6) WASHER CUSHION BOLT (6X25) CUSHION BOLT BOLT J00 COIL ASSY, IGNITION BOLT CLIP (ID:16) 1

40 FIG.22 (1-D-3) SENSOR G00 SENSOR, INLET AIR TEMP J00 GROMMET, AIR TEMP SENSOR J00 BOLT, PTT MOTOR LEAD CLAMP J20 SENSOR ASSY, EXHAUST TEMP J20 SENSOR ASSY, CYLINDER TEMP J03 SENSOR ASSY, TRIM J00 SENSOR ASSY, OIL PRESSURE SCREW (6X10) CLAMP J10 CLAMP, PTT MOTOR LEAD CLAMP (L:145) L00 LEVER, TRIM SENSOR L00 BRACKET, TRIM SENSOR NUT SCREW (5X16) WASHER (5.5X12X0.8) BOLT (6X20) J00 SENSOR, OXYGEN CLAMP J01 HOLDER, TEMP SENSOR J00 HOLDER, OIL SENSOR J00 SENSOR ASSY, OIL TEMP 1

41 FIG.23 (1-D-4) HARNESS J01 CABLE, STARTER MOTOR NUT J40 HARNESS ASSY, WIRING FUSE (10A) FUSE (15A) J00.O-RING, UPPER COVER J00.PULLER, FUSE J00.COVER, FUSE CASE UPPER CUSHION F01.RELAY, ENG CONTROL UNIT F01.RELAY, STARTER MOTOR FUSE (15A) FUSE (30A) FUSE (40A) FUSE (60A) J10.CONNECTOR, SELECT TERMINAL NUT WASHER J00 BRACKET, HARNESS J10 BRACKET, HARNESS J00 BRACKET, HARNESS BOLT CLAMP CLAMP (L:165) CLIP (ID:20) CLAMP CLIP (ID:11.5) CLIP (ID:20) BOLT J10 WIRE ASSY, BATTEERY 1 OPT FUSE (30A) 1 OPT

42 FIG.24 (1-D-5) PTT SWITCH / ENGINE CONTROL UNIT (DF300A E3) J02 SENSOR ASSY, SHIFT POSITION F00.O RING J00 LEVER, SHIFT SENSOR WASHER (5.5X12X0.8) BOLT A WASHER J00 SWITCH ASSY, NEUTRAL SCREW (4X16) CLAMP (L:100) J11 COVER, SWITCH ASSY E04 SWITCH ASSY, PTT CLAMP BOLT J11 SWITCH ASSY, TILT LIMIT CLAMP J00 SCREW, TILT LIMIT CLAMP J12 RELAY, PTT J00 HOLDER, PTT RELAY BOLT CLAMP (L:300) JA1 UNIT, ENGINE CONTROL J00 CUSHION, ENGINE CONTROL UNIT J00 ACTUATOR, SHIFT J00 DAMPER, SHIFT ACTUATOR J00 BRACKET, SHIFT ACTUATOR BOLT BOLT F01 RELAY, ACTUATOR F01 RELAY, OXYGEM SENSOR HEATER J00 HOLDER, RELAY 3

43 FIG.25 (1-D-6) PTT SWITCH / ENGINE CONTROL UNIT (DF250A E3) J02 SENSOR ASSY, SHIFT POSITION F00.O RING J00 LEVER, SHIFT SENSOR WASHER (5.5X12X0.8) BOLT A WASHER J00 SWITCH ASSY, NEUTRAL SCREW (4X16) CLAMP (L:100) J11 COVER, SWITCH ASSY E04 SWITCH ASSY, PTT CLAMP BOLT J11 SWITCH ASSY, TILT LIMIT CLAMP J00 SCREW, TILT LIMIT CLAMP J12 RELAY, PTT J00 HOLDER, PTT RELAY BOLT CLAMP (L:300) JB0 UNIT, ENGINE CONTROL J00 CUSHION, ENGINE CONTROL UNIT J00 ACTUATOR, SHIFT J00 DAMPER, SHIFT ACTUATOR J00 BRACKET, SHIFT ACTUATOR BOLT BOLT F01 RELAY, ACTUATOR F01 RELAY, OXYGEM SENSOR HEATER J00 HOLDER, RELAY 3

44 FIG.26 (1-D-7) CLAMP BRACKET J14-0EP BRACKET, CLAMP STBD (BLACK) J06-0EP BRACKET, CLAMP PORT (BLACK) J01 PLATE, CLAMP BRKT LOWER STBD J01 PLATE, CLAMP BRKT LOWER PORT SCREW (6X10) J12 SHAFT, CLAMP BRKT J11 WASHER, CLAMP BRACKET SHAFT NUT J00 CAP, TRANSOM BOLT BOLT (12.7X115) 1 OPT BOLT (12.7X75) 1 OPT BOLT (12.7X115) NUT WASHER (13.2X45X5) WASHER (13.2X26X3) J02 PLATE, TRANSOM ZINC SET, PROTECTION BOLT (6X25) D02 PIN, TILT LOCK NUT J01 CAM, TILT LIMIT SWITCH J00 HOLDER, TILT LIMIT SWITCH BOLT (6X25) ANODE (MAGNESIUM) 1 OPT J00 COVER, TILT LIMIT SWITCH D00 LEAD (CLAMP TO SWIVEL) SCREW (6X10) 2

45 FIG.27 (1-D-8) SWIVEL BRACKET NIPPLE, GREASE SWIVEL BRKT D00 LEAD (SWIVEL TO MOUNT BRKT) J23-0EP BRACKET, SWIVEL (BLACK) J00 WASHER, SWIVEL TO CLAMP BRKT J00 BUSH, CLAMP SHAFT SWIVEL E00 BUSH, STEERING J02-0EP BRACKET, STEERING (BLACK) SCREW (6X10) WASHER (39.5X64X1) SHIM (39.5X64X0.3) OIL SEAL (39X51X5) CIRCLIP J11 LEVER, TILT LOCK J11 LEVER, TILT LOCK PORT E01 BUSH, TILT STOPPER ROD J00 LINK, TILT LOCK LEVER E10 BRACKET, TILT LOCK SPRING SCREW (6X10) NUT WASHER (6.5X13X1.0) PIN SPRING SPRING 1

46 FIG.28 (1-D-9) TRIM CYLINDER J03 MANIFOLD ASSY E01.FILTER J00.O RING SET J01.PISTON / RAM J01.ROD GUIDE J00..O RING J00.CHECK VALVE J02 CYLINDER ASSY J00.O RING SET J00.PISTON, FREE J00.O RING SET J10 PLUG E00 O RING J20 BOLT, RESERVOIR J01 MANUAL VALVE E00 JOINT, DRIVE J13 SHAFT J00 O RING SET J00 WASHER, TILT CYL TO MANIF J00 VALVE SET, UP BLOW J00 COVER J11 BOLT 1

47 FIG.28 (1-D-10) TRIM CYLINDER J10 PAD, TRIM CYL RAM J00 SHAFT, TILT CYL UPPER J20 NUT, TRIM CYL RAM LOCK WASHER BUSH CIRCLIP BOLT (10X50) J00 RESERVOIR TANK D00 LEAD, PTT TO ANODE D01 LEAD, PTT TO ANODE D01 LEAD, PTT TO ANODE SCREW (6X10) SCREW (6X10) SCREW (6X10) 1

48 FIG.29 (1-D-11) PTT MOTOR J03 MOTOR ASSY, PTT SCREW, YOKE O RING J00.BRUSH SET, PLUS BRUSH SPRING J10.BREAKER HOLDER, BRUSH J00.ARMATURE E00.OIL SEAL J10 BOLT E00 O RING 1

49 FIG.30 (1-D-12) ENGINE HOLDER J03-0EP HOLDER, ENGINE (BLACK) J00 SEAL, ENGINE HOLDER OIL J00 PLUG, WATER J00 GASKET, WATER PLUG J00 SEAL, WATER RETURN J00 GASKET, ENGINE HOLDER J20 UNION, WATER INDICATOR PIN (8X11) BOLT J02 COVER, MOUNT OIL SEAL J00 GASKET, MOUNT OIL SEAL COVER BOLT (8X120) PIN (8X11) A BOLT J00-0EP COVER, ENGINE HOLDER (BLACK) J00 GASKET, ENGINE HOLDER COVER BOLT (8X30) J00 COVER, ENGINE HOLDER UPPER J00 SEAL, ENGINE HOLDER UPPER COV BOLT BOLT J02 PLATE, UPPER MOUNT J01 MOUNT, UPPER BOLT (14X220) NUT WASHER (15X24X3) J02 COVER, UPPER MOUNT BOLT (10X95) BOLT (10X50) J00 STOPPER, UPPER THRUST J00 MOUNT, UPPER THRUST REVERSE BOLT (10X70) BOLT (10X50) BOLT (10X195) 2

50 FIG.30 (1-D-13) ENGINE HOLDER BOLT (10X115) BOLT (8X65) WASHER (8.3X15X3) J00 OIL SEAL J00 SCRAPER 1

51 FIG.31 (1-D-14) DRIVE SHAFT HOUSING J00-0EP HOUSING, DRIVE SHAFT (BLACK) BOLT (10X44) PIN (8X12) D10 BUSH, DRIVE SHAFT RING SCREW (6X10) J00-0EP CASE, EXTENSION (BLACK) 1 W/TRANSOM(XX) STUD BOLT 6 W/TRANSOM(XX) STUD BOLT 1 W/TRANSOM(XX) PIN (8X12) 2 W/TRANSOM(XX) D00 LEAD, MT BRKT TO HSG SCREW (6X10) J00 MOUNT, LOWER THRUST J00 MOUNT, LOWER BOLT (14X220) WASHER (16X32X3) NUT WASHER (16X32X3) J00 BRACKET, LOWER MOUNT J00 COVER, LOWER MOUNT BOLT (10X50) J00 DAMPER, REVERSE STOPPER LOWER WASHER (14X50X4) J10 CLAMP, SPEEDOMETER HOSE J00 BOLT, CLAMP (6X12) J00 ANODE, PROTECTION 1 W/TRANSOM(X) J00 ANODE, PROTECTION 2 W/TRANSOM(XX) BOLT (6X16) 1 W/TRANSOM(X) BOLT (6X16) 2 W/TRANSOM(XX)

52 FIG.32 (1-D-15) GEAR CASE L00-0EP CASE, GEAR (BLACK) L00.WASHER, FORWARD GEAR THRUST BUSH (2X3X11) BEARING (35X56X37) BEARING (80X100X30) BOLT (12X70) 1 W/TRANSOM(X) BOLT (10X55) 6 W/TRANSOM(X) WASHER (10.5X19X2) 6 W/TRANSOM(XX) WASHER (12.5X22X2.5) J20 NUT, EXTENSION BOLT NO.1 6 W/TRANSOM(XX) NUT 1 W/TRANSOM(XX) PIN (8X12) L00 TAB, TRIM BOLT (8X22) J10 PLUG, DRAIN GASKET (9.5X16.5X2) J00 ANODE, PROTECTION BOLT (6X16) J00 RUBBER, EXHAUST SEAL J00 PLATE, EXHAUST SEAL D00 UNION, SPEEDOMETER HOSE B HOSE (4X8X2000) 1 L:2000-> UNION CLAMP (L:100) PIN (6X12) 2

53 FIG.32 (1-E-2) GEAR CASE L00 PROPELLER (3X16X17) 1 OPT W/REGULAR ROTATION L10 PROPELLER (3X16X18.5) 1 OPT W/REGULAR ROTATION L20 PROPELLER (3X16X20) 1 OPT W/REGULAR ROTATION L30 PROPELLER (3X16X21.5) 1 OPT W/REGULAR ROTATION L40 PROPELLER (3X16X23) 1 OPT W/REGULAR ROTATION L50 PROPELLER (3X16X24.5) 1 OPT W/REGULAR ROTATION L60 PROPELLER (3X16X26) 1 OPT W/REGULAR ROTATION L70 PROPELLER (3X16X27.5) 1 OPT W/REGULAR ROTATION J00 PROPELLER (4X15.25X18) 1 OPT W/REGULAR ROTATION J10 PROPELLER (4X15.25X20) 1 OPT W/REGULAR ROTATION J20 PROPELLER (4X15.25X22) 1 OPT W/REGULAR ROTATION J30 PROPELLER (4X15.25X24) 1 OPT W/REGULAR ROTATION J40 PROPELLER (4X15.25X26) 1 OPT W/REGULAR ROTATION

54 FIG.32 (1-E-3) GEAR CASE LA0 PROPELLER (3X16X18.5) 1 OPT W/COUNTER ROTATION LB0 PROPELLER (3X16X20) 1 OPT W/COUNTER ROTATION LC0 PROPELLER (3X16X21.5) 1 OPT W/COUNTER ROTATION LD0 PROPELLER (3X16X23) 1 OPT W/COUNTER ROTATION LE0 PROPELLER (3X16X17) 1 OPT W/COUNTER ROTATION LF0 PROPELLER (3X16X24.5) 1 OPT W/COUNTER ROTATION LG0 PROPELLER (3X16X26) 1 OPT W/COUNTER ROTATION JA0 PROPELLER (4X15.25X20) 1 OPT W/COUNTER ROTATION JB0 PROPELLER (4X15.25X22) 1 OPT W/COUNTER ROTATION JC0 PROPELLER (4X15.25X24) 1 OPT W/COUNTER ROTATION JD0 PROPELLER (4X15.25X26) 1 OPT W/COUNTER ROTATION J10.BUSH SET, PROPELLER 1 OPT

55 FIG.32 (1-E-4) GEAR CASE J00 PROPELLER (3X15.5X17) 1 OPT W/REGULAR ROTATION J10 PROPELLER (3X15.25X19) 1 OPT W/REGULAR ROTATION J20 PROPELLER (3X14.75X21) 1 OPT W/REGULAR ROTATION J30 PROPELLER (3X14.75X23) 1 OPT W/REGULAR ROTATION J40 PROPELLER (3X14.5X25) 1 OPT W/REGULAR ROTATION J50 PROPELLER (3X14.5X27) 1 OPT W/REGULAR ROTATION JA0 PROPELLER (3X15.5X17) 1 OPT W/COUNTER ROTATION JB0 PROPELLER (3X15.25X19) 1 OPT W/COUNTER ROTATION JC0 PROPELLER (3X14.75X21) 1 OPT W/COUNTER ROTATION JD0 PROPELLER (3X14.75X23) 1 OPT W/COUNTER ROTATION JE0 PROPELLER (3X14.5X25) 1 OPT W/COUNTER ROTATION JF0 PROPELLER (3X14.5X27) 1 OPT W/COUNTER ROTATION J00.BUSH SET, PROPELLER 1 OPT L00 STOPPER, PROPELLER BUSH D30 SPACER, PROPELLER NUT NUT WASHER (18.5X31X1) COTTER PIN L00 PLUG, DRAIN J10 CLAMP BOLT E00 KIT, PROPELLER NUT 1 OPT L00 KIT, GEAR CASE SEALING 1 OPT NOT ILLUSTRATED

56 FIG.33 (1-E-5) SIDE COVER J01-0EP COVER, OIL PAN STBD (BLACK) J01-0EP COVER, OIL PAN PORT (BLACK) J00 CUSHION, OIL PAN COV UPPER SCREW (6X17) SCREW (6X65) J20-0EP COVER, SIDE STBD (BLACK) J10-0EP COVER, SIDE PORT (BLACK) J20 SEAL, SIDE COVER PK CLIP (BLACK) J00 PLUG, SIDE COVER SCREW (6X35) J02 HOLDER, SIDE COVER CUSHION BOLT J00 SEAL, FRONT PANEL STBD J00 SEAL, SIDE COVER J00 PROTECTOR, SIDE COVER J02-0EP PANEL, FRONT (BLACK) BOLT (8X40) WASHER CUSHION CUSHION J00 PLUG, WATER J00 GASKET, WATER PLUG J00 RUBBER, SIDE COVER J00 SHAFT, COVER HOOK (FRONT) J20 SHAFT, COVER HOOK (PORT) J30 SHAFT, COVER HOOK (STBD) BUSH WASHER (17X30X3) J00 BUSH J10-0EP LEVER, HOOK RR STBD (BLACK) J10-0EP LEVER, HOOK RR PORT (BLACK) J00-0EP LEVER, HOOK FRONT (BLACK) 1

57 FIG.33 (1-E-6) SIDE COVER J20 BOLT, HOOK LEVER (8X45) 2 (STBD / PORT) J30 BOLT, HOOK LEVER (8X25) 1 (FRONT) WASHER (8.5X28X1.5) WASHER (8.5X16X1.2) J00 SPACER J00 BUSH J00 SPRING, HOOK SHAFT CUSHION J00 GROMMET, REMOCON CABLE CLAMP (L:248) J00 KIT, HOSE ADAPTER 1 OPT J00.ADAPTER, HOSE 1 OPT PLUG (OD:28) 1 OPT

58 FIG.34 (1-E-7) ENGINE COVER (DF300A E3) Y60-0EP COVER SET, ENGINE (BLACK) J10-0EP.COVER, TOP (BLACK) J01.LOUVER, AIR INTAKE J01.GRIP, UPPER COVER STBD J02.GRIP, UPPER COVER PORT J00.SEAL, GRIP STBD J10.SEAL, GRIP PORT J21.SEAL, AIR VENT NO J00.SEAL, AIR VENT NO BOLT BOLT BOLT BOLT BOLT BOLT J00.FASTENER (FRONT) J30.FASTENER (PORT) J40.FASTENER (STBD) GC0-0PG.EMBLEM "S" (CHROME) J00.PROTECTOR, FASTENER J01.BRACKET, FASTENER FRONT J10.BRACKET, FASTENER PORT J10.BRACKET, FASTENER STBD J00.CUSHION, ENG COV FASTENER BOLT BOLT BOLT J32.STRIPE, ENGINE COVER STBD J32.STRIPE, ENGINE COVER PORT J32.DECAL, EFI & VVT 1

59 FIG.34 (1-E-8) ENGINE COVER (DF300A E3) J12 MARK, EMBLEM FRONT (300) J12 MARK, EMBLEM REAR (300) E60 LABEL, ENGINE COVER J00 DECAL, LEAN BURN J00 DECAL (S.S.R.) TOOL SET 1

60 FIG.35 (1-E-9) ENGINE COVER (DF250A E3) Y60-0EP COVER SET, ENGINE (BLACK) J10-0EP.COVER, TOP (BLACK) J01.LOUVER, AIR INTAKE J01.GRIP, UPPER COVER STBD J02.GRIP, UPPER COVER PORT J00.SEAL, GRIP STBD J10.SEAL, GRIP PORT J21.SEAL, AIR VENT NO J00.SEAL, AIR VENT NO BOLT BOLT BOLT BOLT BOLT BOLT J00.FASTENER (FRONT) J30.FASTENER (PORT) J40.FASTENER (STBD) GC0-0PG.EMBLEM "S" (CHROME) J00.PROTECTOR, FASTENER J01.BRACKET, FASTENER FRONT J10.BRACKET, FASTENER PORT J10.BRACKET, FASTENER STBD J00.CUSHION, ENG COV FASTENER BOLT BOLT BOLT J32.STRIPE, ENGINE COVER STBD J32.STRIPE, ENGINE COVER PORT J32.DECAL, EFI & VVT 1

61 FIG.35 (1-E-10) ENGINE COVER (DF250A E3) J72 MARK, EMBLEM FRONT (250) J52 MARK, EMBLEM REAR (250) E60 LABEL, ENGINE COVER J00 DECAL, LEAN BURN J00 DECAL (S.S.R.) TOOL SET 1

62 FIG.36 (1-E-11) FUEL HOSE CAP JOINT CLIP J01 PUMP, SQUEEZE 1

63 FIG.37 (1-E-12) OPT:METER J01 KIT, SPEEDOMETER SUB SENDER ASSY, SPEEDOMETER SCREW D00.UNION, HOSE B.HOSE (4X8X2000) 1 L:2000-> CLAMP (L:100) L00 CONNECTOR, FLUSH WATER L02 KIT, 4 IN MULTI GAUGE L02.GAUGE ASSY, 4 IN MULTI L01.UNIT, INTERFACE L00.HARNESS ASSY, NETWORK POWER L00.UNIT, RESISTOR FEMALE L10.UNIT, RESISTOR MALE L12 KIT, 2 IN MULTI GAUGE L01.GAUGE ASSY, 2 IN MULTI L01.UNIT, INTERFACE L00.WIRE, 25 EXTENSION L00.HARNESS ASSY, NETWORK POWER L00.UNIT, RESISTOR FEMALE L10.UNIT, RESISTOR MALE L00.WIRE, ADAPTER TO DIAGNS L10 GAUGE ASSY, MULTI L10 ADAPTER, GAUGE TERMINAL, RESIN L00 MODULE ASSY, GPS RECIVER L00 WIRE, NETWORK J00 WIRE, GAUGE POWER J10 WIRE, GAUGE POWER 1

64 FIG.38 (1-E-13) OPT:HARNESS J50 WIRE ASSY, REMOCON EXTENSION J10 SET, BATTERY ISOLATOR LEAD CLAMP (L:100) FUSE (40A) BL0 CAP, BCM CONNECTOR J00 CUSHION, BCM J00 RESISTOR, TERMINAL J20 HARNESS ASSY, BCM NO.1 FOR 1 SNGL TERMINAL RESIN J10 CONTROLLER ASSY, BOAT ELECTRIC J00 HOLDER, BCM (L) J00 HOLDER, BCM (R) J00 HARNESS ASSY, DUAL STATION 1 MAIN FUSE (10A) J02 HARNESS ASSY, BCM NO.2 FOR 1 SNGL TERMINAL, RESIN J00 HARNESS ASSY, DUAL ENGINE J30 HARNESS ASSY, BCM NO.1 FOR 1 MULT TERMINAL, RESIN J11 HARNESS ASSY, BCM NO.2 FOR 1 MULT TERMINAL, RESIN J10 HARNESS ASSY, TRIPLE ENGINE CLAMP J00 CONNECTOR, COUNTER SELECT J10 ADAPTER, INTERFACE SINGLE J20 ADAPTER, INTERFACE DUAL J30 ADAPTER, INTERFACE TRIPLE D00 TERIMINAL SET, WITH SLEEVE 1

65 FIG.39 (1-E-14) OPT:SWITCH J03 PANEL ASSY, MAIN SW J00.SWITCH ASSY, MAIN EA0..KEY (941) EB0..KEY (942) E00..KEY (931) E10..KEY (932) E20..KEY (933) E30..KEY (934) E40..KEY (935) E50..KEY (936) E60..KEY (937) E70..KEY (938) E80..KEY (939) E90..KEY (940) E00..CAP, KEY J00.PANEL, MAIN SW J03.SWITCH ASSY, EMERGENCY STOP E01..PLATE ASSY, EMERGENCY 1 SW LOCK E00..NUT SCREW J00.SHEET, MAIN SW PANEL J11 PANEL ASSY, SINGLE J00.NUT J90 BUZZER ASSY, WARNING CLAMP (L:80) J03 PANEL ASSY, EMERGENCY SW E00.PANEL, EMERGENCY STOP SW J21 PANEL ASSY, DUAL J10.NUT J31 PANEL ASSY, TRIPLE J10.NUT 1