HIGH SPEED COMPACT DISC (HCD-32) Operation & Maintenance Manual OPERATORS MANUAL & PART LIST

Transcription

1 HIGH SPEED COMPACT DISC (HCD-32) Operation & Maintenance Manual OPERATORS MANUAL & PART LIST

2

3 Quick Start Guide Hydraulic Connections to Tractor Yellow Lifting/lowering main frame and packers Black Disc gangs Red Forward Unfold System and wing pressure Green Wing axle tires Unfold to Field Position Find a location that is as level as possible. Position the machine in line with the tractor; bring the tractor to a full stop. Remove the safety pins from the wing axle and secure them in the field position holder. From the cab of the tractor, rotate pivot wings 90. Activate forward unfold cylinders (red line) to bring the wings fully forward. Slowly extend the main frame cylinders (yellow line) to lower the machine into field position. Continue lowering the main frame and packers until the packers fully engage the ground and raise the rear of the unit (packer cylinders fully extended). Apply wing down pressure by extending forward unfold cylinders (red line). You should see the wings shift down and the center frame shift up slightly. Release tractor hydraulic remote to lock pressure and allow the accumulators in the circuit to take over while working. Lower the disc gang sections while driving the tractor forward to begin tillage operation (black line). Drive the machine at least 50 metres to check if all packers, discs and wheels are rotating. Adjust the cutting depth if necessary. NOTE: Check the level of A-frame hitch relative to the tractor. Adjust using hitch tongue to level Check the level of bridge beams relative to the hitch A-frame. Adjust packer height by changing packer cylinder shims or by rotating clevis on threaded cylinder rod. FAILURE TO LEVEL THE UNIT CAN RESULT IN UNIT TRACKING TO ONE SIDE DURING OPERATION. FUTHER INFORMATION ON LEVELLING CAN BE FOUND IN YOUR OPERA- TOR S MANUAL. Cutting Depth Adjustment The disc section cylinders contain flip-down spacers. The cutting depth can be controlled by flipping down the appropriate number of spacers onto the shaft of the cylinders. Refer to the chart as a guide to achieve the desired cutting depth. Shims Disc Depth 0 5-1/2 1 5" 2 4.5" 3 4" 4 3.5" 5 3" 6 2.5" 7 2" 8 1.5" 9 1" 1

4

5 Contents SECTION 1 PAGE INTRODUCTION MANUAL & EQUIPMENT DETAILS SPECIFICATIONS PRE-DELIVERY INSPECTION SERVICE & WARRANTY POLICY SAFETY RECOMMENDATIONS DECAL LOCATIONS MAINTENANCE OPERATING INSTRUCTIONS GRADE CHART TORQUE CHART SECTION 2 PAGE PARTS Table of Contents

6

7 SECTION 1 HCD-32

8

9 Thank you for making the decision to purchase a RITE WAY We are pleased to welcome you as an owner of a product from RITE WAY MFG. This machinery is the culmination of years of agricultural and engineering experience and has been designed to deliver you with many years of successful operation service. For the most efficient operation of your HCD-32 we have provided this owner s manual. In this manual we have included proper maintenance and functional procedures to offer maximum longevity for your new equipment. Before operating we urge a careful study of this manual to provide a thorough understanding of your new HCD-32. We also recommend that you take care of this manual so it will be available for future reference. Should your manual become lost or destroyed a new copy can be obtained from your Rite Way Manufacturing dealer. We will also be happy to answer any questions you might have concerning the use or care of this product. Rite Way Manufacturing Co. Ltd. P.O. Box 328 Imperial, Saskatchewan, Canada S0G 2J0 PH: Fax: Web Site: info@ritewaymfg.com Introduction 1

10 Manual Details Unit Model Number HCD-32 Manual Revision Number 2.0 Manual Revision Date July 3th, 2017 Manual Serial Number Range to The area below is provided for the owner / end-user to make notes regarding the equipment. Owner / Equipment Information Serial Number of Unit Date of Purchase Dealer Name Dealer Address Dealer Phone Number Salesman Name Salesman Phone Number Notes 2 Manual Information

11 Specifications General Information Adjustable Disc Cutting Depth from 1-1/2 To 4-5/8 Consistent 5 Disc Spacing Independent Disc Suspension Adjustable Hitch Height With Category 5 Perfect Hitch Aggressive 560/45R22.5 Tires Light Kit Slow Moving Sign Notched 20 Concave Discs (Options Available) Chevron Packer Rollers (Options Available) Heavy Duty Disc Bearings (Options Available) Chrome Plated Pins Main Frame & Wings Heavy Duty 10 x 4 x 0.375W Tube Heavy Duty 8 x 8 x 0.250W Tube Hydraulic System Standard unit requires - 8 Hydraulic Banks. Heavy duty hydraulic welded cylinders. Synchronized Disc Gang Lift Circuit High Mounted Cylinders Accumulator equipped circuits for maximum suspension and contouring Options Rubber Packer Rollers Rubber Packer Rollers With Scrapers Basket Packer Rollers Wavy 20 Concave Discs Smooth 20 Concave Discs Ultra Heavy Duty Disc Bearings Working Width Transport Length Transport Width Transport Height Weight Required Power Ideal Speed Technical Information 32ft (9.75m) 30-4 (9.25m) 13-8 (4.17m) 13-1 (3.99m) 32,000 lbs (14545 kg) 15hp / foot mph (16-19 km/h) Specifications 3

12 Pre-delivery Inspection Check List General Remove wrapping and wash unit, removing all road debris. (Road salt, mud, snow, etc.) Inspect paint, decals and general appearance of unit. Verify that the owners manual is in the manual storage tube. Verify SLOW MOVING VEHICLE sign (SMV) is on unit (if applicable) Verify that jacks are with the unit and function properly. Check wheel bolts for proper torque. Check for proper tire pressure (PSI). Verify that the wheel hubs are lubricated. Verify that locking pins and / or ram locks are in place. Lubricate all components as per operators manual recommendation. Check that all bolts and fasteners are at the proper torque specifications. (NOTE: All cap screws that have lock nuts join moving pieces should not be tightened completely, they must allow movement. i.e. Spring pressure kits, rock shaft connector, draft arm, etc. Check sprocket alignment and chain tension. (If applicable) Check locking collars and set screws for proper tension. (If applicable) Verify operation of lights. (If applicable) Verify the unit moves IN and OUT of transport without any binding. Verify that tires are tracking properly when in transport mode. Hydraulics Insure that all hydraulic hoses and lines are routed properly and secured. Verify that all hydraulic fittings / hoses are secure and there are no oil leaks. Inspect all cylinders for leakage and the cylinder shaft for rust, pits, or scratches. Verify operation of all hydraulic functions - Cycle hydraulic cylinders to remove air from the system. Delivery Verify that The customer is aware of warning decals and proper jack placement for transport.. Verify that The customer is aware of proper operation and transportation of the unit. Verify that The customer has received an operators manual. Explain all maintenance and service intervals to the customer (From operators manual). Advise the customer of grease zerk locations and maintenance schedules. Level the unit per operators manual and instruct the customer on the proper procedures. Pre-delivery Inspection Completed By (Sign Below) Pre-delivery Inspection Confirmed By (Sign Below) 4 Pre-delivery Inspection Check List

13 Service & Warranty Policy Rite Way Manufacturing Co. Ltd. (hereafter referred to as Rite Way) warrants each new machine to be free from defects in materials and workmanship for a period of one (1) year from date of purchase under normal agricultural use and service. In addition, Rite Way will supply at no charge, (F.O.B Rite Way Factory) any part that has failed within the 2nd year. Rite Way s obligation under this warranty is limited to the repair or replacement of any defective parts of the equipment at its own discretion. Any alterations, modifications or additions done to a finished product will void this warranty unless prior written permission from Rite Way is obtained. Items that are not manufactured by Rite Way are covered by the warranty of the supplier of these items. We will therefore extend, without assuming any responsibility, any warranty given to us by our suppliers. This warranty shall-not apply to any machine, that in the company s judgment has be subjected to misuse, negligence or accident. In no event shall the owner be entitled to recover costs for incidental, special or consequential damages such as, but not limited to; Loss of crop, loss of profit or revenue, other commercial losses, inconvenience or rental costs. This warranty shall not apply unless Rite Way or its designated dealer is promptly notified of claimed defects and the allegedly defective part is held for inspection. Repair parts purchased for machines Out of Warranty, are warranted to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of delivery to the customer. The warranty shall only become valid when delivery notification for warranty is received by Rite Way within 20 days of the completion of sale. OWNER S / USERS OBLIGATION: It is the responsibility of the user to read the Operators Manual and understand the safe and correct operating procedures as it pertains to the operation of the product, and to lubricate and maintain the product according to the maintenance schedule in the Manual. The user is responsible for inspecting the machine, and for having parts repaired or replaced when continued use of the product could cause damage or excessive wear to any other parts. It is the user s responsibility to deliver their machine to a Rite Way dealer for service or replacement of defective parts which are covered by the standard warranty. Rite Way will not by held responsible for charges such as transportation, fuel, lodging when a dealer / dealer representative travels to a customer location for warranty or inspection. Service & Warranty Policy 5

14 Service & Warranty Claim Procedure 1. All claims must be handled through a dealer / distributor. All claims must be submitted on a properly completed claim form within 30 days of the date of repair. 2. A warranty registration claim form must be on file at Rite Way Mfg. to validate a warranty claim. 3. Defective parts are to be held at the dealer / distributor s place of business until the warranty claim form has been processed. Rite Way will advise when parts can be released. 4. Parts that require inspection by Rite Way personnel must be accompanied by a Return Goods Form number, and must be sent by pre-paid freight. Rite Way will refund pre-paid freight charges on any items determined to be defective. 5. Rite Way will not assume responsibility for repairs or expenses incurred without authorization. Warranty labour in excess of $ must be authorized before such work is performed and photographs before and after repairs are required. 6. Warranty labour is to be claimed on the warranty claim form, only if the warranty labour was performed by the dealer. Travel time is not covered by warranty and should not be included. Rite Way reserves the right to adjust or allocate labour times and values based on its experience. 7. It is the responsibility of the dealer to ensure that the warranty registration forms are properly completed and returned to Rite Way Mfg., Imperial, SK. 6 Service & Warranty Policy

15 Safety Recommendations 1. Read manual thoroughly before operating machine. 2. Study all warning decals on implement. 3. Most accidents occur because of neglect or carelessness. 4. Do not allow riders on the tractor or implement during operation. 5. Do not allow children on or near the machine. 6. Connect the implement hitch to the tractor before operating the hydraulic system. NOTE: Be aware of any hydraulic leaks. 7. Always throttle the tractor down and use caution when connecting the implement to the tractor hitch. NOTE: Never stand between the tractor and implement. 8. Lower the hitch jack onto firm ground and chock the tires when un-hooking implement from tractor. NOTE: Ensure the unit is on level ground prior to un-hooking tractor. 9. Exercise extra caution when working on hillsides or near ditches. 10. Ensure that the tractor draw-bar is pinned during transport. 11. Maximum speed while transporting the HCD-32 is 38 mph (60 km/h). 12. Ensure that the HCD-32 frame is lowered to the ground before doing any work on machine. NOTE: If it is necessary to work on machine with the drawbar raised, ensure that cylinders are locked in position using the lock pin. 13. Do not work on this machine when hydraulic system is under pressure. 14. Observe all laws and regulations when transporting unit on public roads. 15. Do not transport this machine on public roads unless all safety & maintenance checks have been completed. This machine will provide years of trouble-free & safe operation IF all maintenance and safety instructions are followed. Safety Recommendations 7

16 HCD-32 Decal Locations 1 Front Facing Portions of Machine, Several Locations 2 Rear Facing Portions of Machine, Several Locations 3 Beside Each Grease Location (See Pages 12-13) Decal Locations 8

17 Decal Locations Item # Part # Description Amber Reflector (3 x 2) Red Reflector (3 x 2) Grease Every 8 Hours Caution - Escaping Fluid Hazard Important - Block Wheels Warning - Lower or Block Elevated Components Riteway Serial Number Plate Attention - Insure That All Cylinders Are Retracted Warning - Check And Tighten Hub Riteway Mfg. (Large Decal, 31 x 5 - White) Important - Hydraulic Hose Application ONE TILL (LARGE) ONE TILL UNIT SERIES UNIT SIZE MODEL YEAR UNIT NUMBER 9 Decal Locations 9

18 Maintenance General Repack the wheel hubs after the first 500 kilometres of travel ; then yearly thereafter. Visually inspect the wheel bolts for tightness each day. Torque to 110 lbs ft (149 Nm) after the first few hours of operation and frequently thereafter. (Manufacturer s torque recommendations: 90 to 131 lbs ft (122 Nm to 178 Nm)). After first eight hours of operation in the field check the roller drum bearing locking collar then check it annually and tighten as necessary. Every 8 Hours (Daily) Grease all pins. (See decals locations) Every 100 Hours (Monthly) Visually inspect hydraulic hoses & fittings for leaks or damage. Annually Inspect wheel bearings / hubs for tightness and grease. Check wheel bolts for tightness and re-torque. Check tire pressure. Recommended pressure: 58 psi. Visually inspect unit for loose, worn or damaged components. 10 Maintenance

19 Maintenance Storage Coat any exposed cylinder shafts with thick oil or grease. Ensure that parking jacks are situated on firm ground. Failure to do so may cause the hitch to rise sharply as the jack pads sink into the ground. Lock all applicable safety pins into place. NOTE: All fasteners with locknuts that are used to join moving pieces should not be tightened completely to allow for movement. Maintenance 11

20 HCD-32 Maintenance Grease Locations 12 Maintenance

21 HCD-32 Maintenance Grease Locations (Cont.) Maintenance 13

22 Operating Instructions Tire Pressure: Transport 58psi, Field 35 psi In transport position, the maximum turning angle is 40. Turning too tight will cause severe damage to the machine. Always choose a level area when folding the unit in or out of transport mode. Lubricate all pins, axles and bearings regularly to prevent premature failure. Clean hydraulic hose ends prior to coupling with tractor hydraulic system. The HCD requires four sets of hydraulic outlets to operate the machine. Yellow Lifting/lowering main frame and packers Black Disc gangs Green Wing axle tires Red Wing fold and wing pressure General Information Hitch A-Frame Left Wing Center Bar Right Wing 14 Operating Instructions

23 Operating Instructions Tractor Hook-Up Tractor Hook-up Move the tractor into position where the pin can be dropped in place through the draw bar hitch. If there is too much negative hitch weight, you can lower the hitch by connecting the yellow main frame/packer circuit and adjusting the hitch. Retract the parking jack and move to inboard frame storage position before moving the machine. NOTE: Use a clevis-type tractor hitch with a retained type of hitch pin. NOTE: Ensure that the parking jack handle is secured by chain prior to moving the machine. Failure to do so will destroy the jack handle. Hook up the four hydraulic circuits to your tractor remote. Recommended Hydraulic Connections: Remote 1 Black Disc gangs Remote 2 Yellow Lifting/lowering main frame and packers Remote 3 Red Wing fold and wing pressure Remote 4 Green Wing axle tires Tractor Disconnecting Field Position Ensure that the packers and disc gangs are fully lowered. Chock the A-frame tires, front and back, before disconnecting from the tractor. Lower the parking jack into position until upward pressure is applied and the hitch is raised off of the tractor clevis. Tractor Disconnecting Transport Position Ensure that the packers and disc gangs are fully raised. Chock the A-frame tires, front and back, before disconnecting from the tractor. Lower the parking jack into position until upward pressure is applied and the hitch is raised off of the tractor clevis. NOTE: Ensure the jack is placed on firm ground prior to unhooking. NOTE: The hitch may rise suddenly. If it does, re-connect the yellow hydraulic circuit and adjust the height downward. Operating Instructions 15

24 Operating Instructions Transport to Field Position Hook up tractor according to prior instructions. Ensure that the safety pins are in transport position. When entering the field from transport mode, find a level location. Position the machine in-line with the tractor and bring the tractor to a full stop. Remove the wheel pivot safety pins from transport position to field position and secure (fig. 1). NOTE: Failing to do so may cause severe damage to the machine. Safety Pin (transport position) Safety Pin (field position) Figure 1 16 Operating Instructions

25 Operating Instructions Transport to Field Position (Cont.) Rotate wing axle tires 90 degrees (green line) (fig. 2). Activate forward unfold cylinders (red line) to open wings until they are in line with the centre section (fig. 3). Slowly extend the main frame cylinders (yellow line) so that the whole machine goes over center the hitch goes up slightly (fig. 4). NOTE: There will be significant negative hitch tongue weight when the unit is lowered into field position. Ensure that the unit is securely attached to the clevis hitch of the tractor to prevent upending. Figure 2 Figure 3 Figure 4 Operating Instructions 17

26 Operating Instructions Transport to Field Position (Cont.) Proceed with lowering the frame until the packers touch the ground. Hold the remote connected to the yellow circuit pressure and ensure packer cylinders extend fully. (fig. 5) (fig 6). Extend wing fold cylinders (red line) until the centre section is level with the wings (approximately 1-2 inches of chrome rod showing on all wing fold cylinders). Drive forward at 10-12MPH. Lower disc sections to begin working (black hydraulic line) (fig. 7). Figure 5 Figure 6 Figure 7 18 Operating Instructions

27 Operating Instructions Leveling and Depth Adjustment A-frame to Tractor Move the unit to field position on level ground Measure from bottom of tubing on the A-frame to the ground near the implement s tire. Measure from bottom of tubing and the A-frame to the ground near the tractor. Adjust the hitch-clevis accordingly so the A-frame is level (± 1 difference allowed). Main Frame to Ground With the A-frame leveled and the unit on level ground, check the level of the centre bridge. The bridge should be level within ½ from front to rear. If the bridge is not level, lower the discs to the ground and raise packers slightly to take weight off the packer cylinders. Un-pin packer cylinder clevis and thread on/off as necessary and replace clevis pins. Clockwise turn=shorter cylinder pin-pin=lower rear of frame. Re-apply pressure to A-frame/packers and check for level. Repeat as necessary until unit is level from rear to rear. NOTE: An out of level machine will cut deeper on the front or rear row of disks and therefore will skew to one side while working with disks down. Cutting Depth Adjustment The disc gang cylinders are equipped with a custom clevis containing flip down shims. A desired number of spacers can be rotated onto the cylinder rod by removing the quick adjust pin. This will control your cutting depth as shown in the chart (depending on level of disc wear): NOTE: ¼ thick depth shim flipped down = ½ shallower disc depth Shims Disc Depth 0 5-1/2 1 5" 2 4.5" 3 4" 4 3.5" 5 3" 6 2.5" 7 2" 8 1.5" 9 1" Operating Instructions 19

28 Operating Instructions Fully raise disc sections off the ground (black hydraulic line) (fig. 8). Bring the machine to a full stop on a level part of the field. Raise the main sections of the machine and the packers (yellow hydraulic line). Make sure the main lift cylinders are fully retracted. (fig. 9) (fig. 10). Field to Transport Position NOTE: Be prepared for over-centre movement of the main frame. Figure 8 Figure 9 Figure Operating Instructions

29 Operating Instructions Field to Transport Position (Cont.) Activate forward unfold cylinders to bring the wings into transport position. If the wings do not go all the way back, adjust the pivot wheels while folding the wings. Adjust wing fold cylinders so both wings are straight back. (fig. 11)(fig. 12) Rotate wing axle wheels 90 until the wheels point forward (green line) (fig. 13). Move the safety pins to transport position from field position and secure it with a cotter pin (fig. 1). NOTE: If you cannot fold up the wings, fully unfold, lower the main frame, and drive to a more level location before attempting the fold. Figure 11 Figure 12 Figure 13 Operating Instructions 21

30 Grade Chart Specification Material Size Range (inches) Min. Proof Strength (psi) Min. Tensile Strength (psi) Min. Yield Strength (psi) Grade Identification Marking Grade 2 Low or Medium Carbon Steel 1/4 to 3/4 7/8 to 1-1/2 55,000 33,000 74,000 60,000 57,000 36,000 Grade 5 Medium Carbon Steel: Quenched and Tempered 1/4 to 1 1-1/8 to 1-1/2 85,000 74, , ,000 92,000 81,000 Grade 8 Medium Carbon Alloy Steel: Quenched and Tempered 1/4 to 1-1/2 120, , , Grade Chart

31 Torque Chart Grade 2 Grade 5 Grade 8 Nominal Thread Size Clamping Load Tightening Torque Clamping Load Tightening Torque Clamping Load Tightening Torque Coarse Thread 1/4-20 1,300 lbs 65 in-lbs 2,000 lbs 100 in-lbs 2,850 lbs 143 in-lbs 5/ ,150 lbs 134 in-lbs 3,350 lbs 210 in-lbs 4,700 lbs 305 in-lbs 3/8-16 3,200 lbs 20 ft-lbs 4,950 lbs 31 ft-lbs 6,950 lbs 44 ft-lbs 7/ ,400 lbs 30 ft-lbs 6,800 lbs 50 ft-lbs 9,600 lbs 70 ft-lbs 1/2-13 5,850 lbs 49 ft-lbs 9,050 lbs 75 ft-lbs 12,800 lbs 107 ft-lbs 9/ ,500 lbs 70 ft-lbs 11,600 lbs 109 ft-lbs 16,400 lbs 154 ft-lbs 5/8-11 9,300 lbs 97 ft-lbs 14,500 lbs 151 ft-lbs 20,300 lbs 211 ft-lbs 3/ ,800 lbs 173 ft-lbs 21,300 lbs 266 ft-lbs 30,100 lbs 376 ft-lbs 7/8-9 11,425 lbs 166 ft-lbs 29,435 lbs 430 ft-lbs 41,550 lbs 606 ft-lbs ,000 lbs 250 ft-lbs 38,600 lbs 640 ft-lbs 54,540 lbs 900 ft-lbs Fine Thread 1/4-28 1,500 lbs 75 in-lbs 2,300 lbs 115 in-lbs 3,250 lbs 163 in-lbs 5/ ,400 lbs 150 in-lbs 3,700 lbs 230 in-lbs 5,200 lbs 325 in-lbs 3/8-24 3,600 lbs 23 ft-lbs 5,600 lbs 35 ft-lbs 7,900 lbs 50 ft-lbs 7/ ,900 lbs 36 ft-lbs 7,550 lbs 55 ft-lbs 10,700 lbs 78 ft-lbs 1/2-20 6,600 lbs 55 ft-lbs 10,200 lbs 85 ft-lbs 14,400 lbs 120 ft-lbs 9/ ,400 lbs 79 ft-lbs 13,000 lbs 112 ft-lbs 18,300 lbs 172 ft-lbs 5/ ,600 lbs 110 ft-lbs 16,300 lbs 170 ft-lbs 23,000 lbs 240 ft-lbs 3/ ,400 lbs 193 ft-lbs 23,800 lbs 298 ft-lbs 33,600 lbs 420 ft-lbs 7/ ,610 lbs 184 ft-lbs 32,480 lbs 473 ft-lbs 45,855 lbs 668 ft-lbs Torque Chart 23

32

33 SECTION 2 ITEMS HIGLIGHTED RED HAVE INDIVIDUAL BREAK-DOWNS

34

35

36 A-Frame, Hitch 04 A-Frame, Hitch

37 A-Frame, Hitch Item # Part # Description A FRAME WELDMENT (X-STYLE) HYDRAULIC CLAMP, 2 LINE, BLACK PLASTIC BOLT, 3/8-16 UNC - 3, GR.5, YELLOW ZINC PLATED, W THREAD LOCK WASHER, FLAT, 3/8 - Regular, GR.5, YELLOW ZINC PLATED " SHEPHERD HOOK HOSE STANDOFF SAFETY CHAIN 20,000LB, CLEVIS MOUNT, NEW STYLE " SIDE WINDER 3000 lb PARKING JACK Crossover Hitch - CAT MANUAL STORAGE TUBE MANUAL STORAGE TUBE CAP CLAMP, 6.00" DIAMETER NUT, HEX, INCH, GRADE 5, YELLOW ZINC PLATED NUT, STOVER LOCK, 3/8-16 UNC, GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 1-8 UNC, GR.5, YELLOW ZINC PLATED NUT, NYLOCK, HEX, INCH, GRADE 5, YELLOW ZINC PLATED BOLT, 3/8-16 UNC - 1, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED BOLT, 1-8 UNC - 3.5, GR.8, YELLOW ZINC PLATED BOLT, 1-8 UNC - 8, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/8 - Regular,GR.5, YELLOW ZINC PLATED WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED ACCUMULATOR, 1.4L, #8 ORB, CHARGED TO 1800PSI r2 CHAIN AND TIP HOLDER 14-1/4 X MOUNT, HYDRAULIC BULKHEAD - #6 & #8 JIC ACCUMULATOR MOUNT, 3 POSITION BOLT, 3/8-16 UNC , GR.8, YELLOW ZINC PLATED BOLT, 3/8-16 UNC , GR.8, YELLOW ZINC PLATED BOLT, HEX, INCH, GRADE 5, YELLOW ZINC PLATED NUT, STOVER LOCK, 3/8-16 UNC, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 3/8" - USS, GR.5, YELLOW ZINC PLATED A-Frame, Hitch 05

38 A-Frame, Center Axle 06 A-Frame, Center Axle

39 A-Frame, Center Axle Item # Part # Description CENTER BRIDGE WELDMENT A-FRAME AXLE CTD 812 AXLE STUB NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8 - narrow, GR.5, YELLOW ZINC PLATED HUB ASSEMBLY, INCL BEARINGS, SEALS, CAP WHEEL HUB, DUST CAP SPINDLE, 1010 SERIES, 3" OD X 17.38" LNG, LB /4 WHEEL STUD, NF /4" FLANGE NUT TIRE / RIM ASSY, 560/45R BOLT, 3/4-10 UNC - 5, GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 4.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 6.0" x 32", 3.0" SHAFT, WELDED PIN, 1.75 X MAIN FRAME LIFT CYLINDER PIN, HITCH TO CENTER FRAME PIN, MAIN LIFT CYLINDER TO CENTER FRAME A-Frame, Center Axle 07

40 Center Frame 08 Center Frame

41 Center Frame Item # Part # Description PIN WELDMENT, WING HOOK, CYLINDER, YZP GANG LINK, WITH LUG GANG LINK, WITHOUT LUG WING WELDMENT, LEFT A-FRAME ASSEMBLY HCD DISC DEPTH SHIM ASSEMBLY NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 4, GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 4.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 6.0" X 32", WELDED CYLINDER, HYD - REPHASING 4.00" X 10", WELDED PIN, HITCH TO CENTER FRAME PIN, CENTER FRAME TO WING PIN, MAIN LIFT CYLINDER TO CENTER FRAME PIN, PARALLEL LINK TO BRIDGE PIN, PARALLEL LINK TO GANG PIN, PACKER MOUNT, HYDRAULIC BULKHEAD 6 X #6 JIC - OFFSET BOLT, 3/8-16 UNC , GR.8, YELLOW ZINC PLATED Center Frame 09

42 Wing (Left Pictured) 10 Wing (Left Pictured)

43 Wing (Left Pictured) Item # Part # Description GANG LINK, WITHOUT LUG CENTER BRIDGE WELDMENT 6* WING WELDMENT, LEFT 6* WING WELDMENT, RIGHT WING FOLD ROCKER WELDMENT PIN, WING FOLD ROCKER COIL PACKER MOUNT WELDMENT, MEDIUM NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 4, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 3.5" X 8", WELDED PIN, CENTER FRAME TO WING PIN, PARALLEL LINK TO BRIDGE PIN, PACKER Disc Gang, Center 11

44 Wing - Cont. (Left Pictured) 12 Wing (Left Pictured)

45 Wing - Cont. (Left Pictured) Item # Part # Description PIN WELDMENT, WING HOOK, CYLINDER, YZP WING AXLE, SAFETY PIN WELDMENT GANG LINK, WITH LUG 7* LEFT WING AXLE WELDMENT 7* RIGHT WING AXLE WELDMENT HCD DISC DEPTH SHIM ASSEMBLY A AMBER WARNING LIGHT A RED WARNING LIGHT SLOW MOVING SIGN SLOW MOVING SIGN SPADE NUT, JAM, 1-8 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/4-20 UNC , GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED NUT, STD, 1/4-20 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1-8 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/4" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 4.0" X 10", WELDED CYLINDER, HYD - REPHASING 3.5" X 10", WELDED HUB & SPINDLE ASSY /4 WHEEL STUD, NF /4" FLANGE NUT TIRE / RIM ASSY, 560/45R PIN, PARALLEL LINK TO GANG WING BRIDGE LIGHT MOUNT BOLT, 3/8-16 UNC , GR.8, YELLOW ZINC PLATED BOLT, 3/4-10 UNC - 5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED Disc Gang, Center 13

46 Disc Gang, Center 14 Disc Gang, Center

47 Disc Gang, Center Item # Part # Description CENTER BRIDGE WELDMENT GANG CONNECT LINK BAR WELDMENT GANG MOUNT BAR WELDMENT, CENTER, REAR GANG MOUNT BAR WELDMENT, CENTER, FRONT DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED PIN, PARALLEL LINK TO GANG Disc Gang, Center 15

48 Disc Gang, Right 16 Disc Gang, Right

49 Disc Gang, Right Item # Part # Description WING WELDMENT, RIGHT GANG CONNECT LINK BAR WELDMENT GANG MOUNT BAR WELDMENT, RIGHT, REAR GANG MOUNT BAR WELDMENT, RIGHT, FRONT GANG BAR EXTENSION WELDMENT GANG BAR FINISHING DISC WELDMENT DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY DISC MOUNT ARM - RIGHT END NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC , GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED GANG SECTION FINISHING PLATE, EXTENDED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED PIN, PARALLEL LINK TO GANG Disc Gang, Right 17

50 Disc Gang, Left 18 Disc Gang, Left

51 Disc Gang, Left Item # Part # Description WING WELDMENT, LEFT GANG CONNECT LINK BAR WELDMENT GANG MOUNT BAR WELDMENT, LEFT, REAR GANG MOUNT BAR WELDMENT, LEFT, FRONT GANG BAR EXTENSION WELDMENT GANG BAR FINISHING DISC WELDMENT DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY DISC MOUNT ARM - LEFT END NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED GANG SECTION FINISHING PLATE NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED PIN, PARALLEL LINK TO GANG Disc Gang, Left 19

52 Packer Sections, Center 20 Packer Sections, Center

53 Packer Sections, Center Item # Part # Description PIN WELDMENT, PACKER CYLINDER TO BRIDGE CENTER BRIDGE WELDMENT COIL PACKER MOUNT WELDMENT, CENTER 2 PIECE - LEFT COIL PACKER MOUNT WELDMENT, CENTER 2 PIECE - RIGHT SCRAPER MOUNT SIDE PLATE LEFT SCRAPER MOUNT SIDE PLATE RIGHT SCRAPER BAR SMALL SMALL RUBBER PACKER ROLLER, 16", 0.25"W BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED RUBBER PACKER RUBBER PACKER ROLLER, SMALL, SHAFT RUBBER PACKER RETAINING RING /16" ID LOCK COLLAR /16"Ø FLANGE BEARING C/W ECENTRIC COLLAR NUT, JAM, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 2, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED BOLT, 5/8-11 UNC - 4, GR.8, YELLOW ZINC PLATED 29* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 29* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED COIL PACKER, BEARING MOUNT PLATE PACKER MOUNT BOLT PLATE SPACER RUBBER PACKER SCRAPER BLADE SMALL NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 2.5" X 6", WELDED PIN, PACKER Packer Sections, Center 21

54 Packer Sections, Wing, Outer 22 Packer Sections, Wing, Outer

55 Packer Sections, Wing, Outer Item # Part # Description PIN WELDMENT, PACKER CYLINDER TO BRIDGE WING WELDMENT, RIGHT COIL PACKER MOUNT WELDMENT, LARGE SCRAPER MOUNT SIDE PLATE LEFT SCRAPER BAR LARGE SCRAPER MOUNT SIDE PLATE RIGHT LARGE RUBBER PACKER ROLLER, 16", 0.25"W BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED RUBBER PACKER 409mmID x 586mmOD RUBBER PACKER ROLLER, LARGE, SHAFT RUBBER PACKER RETAINING RING /16" LOCK COLLAR, PLTD /16"Ø FLANGE BEARING c/w ECENTRIC COLLAR BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 23* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 23* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED COIL PACKER, BEARING MOUNT PLATE RUBBER PACKER SCRAPER BLADE LARGE NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 2.5" X 6", WELDED PIN, PACKER Packer Sections, Wing, Outer 23

56 Packer Sections, Wing, Inner 24 Packer Sections, Wing, Inner

57 Packer Sections, Wing, Inner Item # Part # Description PIN WELDMENT, PACKER CYLINDER TO BRIDGE WING WELDMENT, RIGHT COIL PACKER MOUNT WELDMENT, MEDIUM SCRAPER MOUNT SIDE PLATE LEFT SCRAPER MOUNT SIDE PLATE RIGHT SCRAPER BAR MEDIUM MEDIUM RUBBER PACKER ROLLER, 16", 0.25"W BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED RUBBER PACKER 409mmID x 586mmOD RUBBER PACKER ROLLER, MEDIUM, SHAFT RUBBER PACKER RETAINING RING /16" LOCK COLLAR, PLTD /16"Ø FLANGE BEARING c/w ECENTRIC COLLAR BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED BOLT, 1/2-13 UNC , GR.8, YELLOW ZINC PLATED NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 23* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 23* COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED COIL PACKER, BEARING MOUNT PLATE RUBBER PACKER SCRAPER BLADE MEDIUM NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED CYLINDER, HYD - 2.5" X 6", WELDED PIN, PACKER Packer Sections, Wing, Inner 25

58 Disc Gang, Shank 26 Disc Gang, Center

59 Disc Gang, Shank Item # Part # Description 1* SHANK WELDMENT, ONE PIECE, LEFT CUT 1* SHANK WELDMENT, ONE PIECE, RIGHT CUT NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED BOLT, 3/4-10 UNC - 2.5, GR.8, YELLOW ZINC PLATED JAM NUT 7/8" -14 UNF FLANGE NUT 7/8" - 14 UNF BOLT, 1/2-20 UNF - 1, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED ISOLATOR, RUBBER, TORSION DISC HUB ASSEMBLY AG-1418, 6 HOLES X 100MM 11* DISC, 20" OD, 6 HOLE PATTERN,NOTCHED 11* DISC, 20" OD, 6 HOLE PATTERN,SERRATED 11* DISC, 20" OD, 6 HOLE PATTERN, SMOOTH SHANK, ONE PIECE, UPPER CLAMSHELL Disc Gang, Center 27

60 Disc Gang, Finishing Shank 28 Disc Gang, Finishing Shank

61 Disc Gang, Finishing Shank Item # Part # Description CENTER BRIDGE WELDMENT 1* SHANK WELDMENT, FINISHING, RIGHT CUT 1* SHANK WELDMENT, FINISHING, LEFT CUT NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED BOLT, 3/4-10 UNC - 2.5, GR.8, YELLOW ZINC PLATED JAM NUT 7/8" -14 UNF FLANGE NUT 7/8" - 14 UNF BOLT, 1/2-20 UNF - 1, GR.8, YELLOW ZINC PLATED WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED ISOLATOR, RUBBER, TORSION DISC HUB ASSEMBLY AG-1418, 6 HOLES X 100MM DISC, 20" OD, 6 HOLE PATTERN,SMOOTH SHANK, ONE PIECE, UPPER CLAMSHELL Disc Gang, Finishing Shank 29

62 Roller Packers 30 Roller Packers

63 Roller Packers Item # Part # Qty Description 1* CHEVRON PACKER ROLLER, 16", LARGE 1* CHEVRON PACKER ROLLER, 16", MEDIUM 1* CHEVRON PACKER ROLLER, 16", SMALL 2* BASKET PACKER ROLLER, LARGE 2* BASKET PACKER ROLLER, MEDIUM 2* BASKET PACKER ROLLER, SMALL 3* RUBBER PACKER ROLLER, LARGE 3* RUBBER PACKER ROLLER, MEDIUM 3* RUBBER PACKER ROLLER, SMALL Roller Packers 31

64 Depth Spacers 32 Depth Spacers

65 Depth Spacers Item # Part # Description CENTER BRIDGE WELDMENT GANG LINK, WITH LUG HCD DEPTH SHIM ROD CLEVIS MACHINED STEEL COMPRESSION SPRING ZP STEEL CLEVIS PIN, YZP, W HAIRPIN AND LANYARD NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 7* HCD DEPTH ADJUST SHIM THIN 1/4" 7* HCD DEPTH ADJUST OFFSET SHIM THIN 1/4" CYLINDER, HYD - REPHASING 4.00" X 10", WELDED Depth Spacers 33

66 RAM 6 X 32 X 3 RAM PART NUMBER R RITE WAY PART NUMBER Item # Part # Description 1 R BARREL WELDMENT 2 R SHAFT WELDMENT 3 R PISTON 4 R GLAND 5 R SET SCREW, SOCKET, 3/8-16 UNC x 3/8 LG 6-13 R SEAL KIT 34 Cylinders

67 RAM 2-1/2 X 6 X 1-1/4 RAM PART NUMBER R RITE WAY PART NUMBER Item # Part # Description 1 R BARREL WELDMENT 2 R A SHAFT 3 R PISTON 4 R GLAND 5 R LOCKNUT, 7/8-14 UNF, GRADE C 6 R CLEVIS 7 R HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R NUT, HEX, 3/8-16 UNC, GR R SEAL KIT Cylinders 35

68 RAM 3 X 6 X 1-1/4 RAM PART NUMBER R RITE WAY PART NUMBER Item # Part # Description 1 R BARREL WELDMENT 2 R A SHAFT 3 R PISTON 4 R GLAND 5 R LOCKNUT, 7/8-14 UNF, GRADE C 6 R CLEVIS 7 R HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R NUT, HEX, 3/8-16 UNC, GR R SEAL KIT 36 Cylinders

69 RAM 3-1/2 X 8 X 1-3/4 RAM PART NUMBER R RITE WAY PART NUMBER Item # Part # Description 1 R BARREL WELDMENT 2 R A SHAFT 3 R PISTON 4 R GLAND 5 R LOCKNUT, 1 1/4-12 UNS, GRADE C 6 R CLEVIS 7 R HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R NUT, HEX, 3/8-16 UNC, GR R SEAL KIT Cylinders 37

70 RAM 4 X 10 X 2 RAM PART NUMBER R RITE WAY PART NUMBER Item # Part # Description 1 R BARREL WELDMENT 2 R A SHAFT 3 R PISTON 4 R GLAND 5 R LOCKNUT, 1 1/8-12 UNF, GRADE C 6 R CLEVIS 7 R HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR. 8 8 R NUT, HEX, 3/8-16 UNC, GRADE R SEAL KIT 38 Cylinders

71 MONARCH 3-1/2 X 10 X 1-1/4 MONARCH PART NUMBER RITE WAY PART NUMBER Item # Part # Description Piston Rod Seal Kit Clevis Cylinders 39

72 MONARCH 3-3/4 X 10 X 1-3/8 MONARCH PART NUMBER RITE WAY PART NUMBER Item # Part # Description Piston Rod Seal Kit Clevis 40 Cylinders

73 MONARCH 4 X 10 X 1-3/8 MONARCH PART NUMBER RITE WAY PART NUMBER Item # Part # Description Piston Rod Seal Kit Clevis Cylinders 41

74 NOTES 42

75 NOTES 43