Express Series Multi Configuration Composite Body Bridge / Frac Plugs

Size: px

Start display at page:

Download "Express Series Multi Configuration Composite Body Bridge / Frac Plugs"

Robert Phillips
5 years ago
Views:

1 Multi Configuration Composite Body Bridge / Frac Plugs The Express Series Bridge and Frac Plugs utilize a unique combination of composites to provide a dependable, durable, and cost-efficient method for temporary zone isolation during stage fracs in both vertical and horizontal wells. The Express Series Plugs are constructed primarily from composite with cast iron slips ensuring fast drill times while remaining reliable. The Express Series Plug is a multi-configuration plug allowing for a user to easily convert the tool from a Ball Drop to a Caged Ball or Bridge Plug. This conversion is easily obtained using two simple kits (Bridging Pin / Caged Ball Assembly). Express Series Plugs can be run with any wireline setting tool or tubing run hydraulic setting tool. Cast iron slips are hardened to wicker depth only and can be set in up to P110 casing. Available in 4 ½ and 5 ½. (other sizes pending) Sets securely in up to P110 Grade. Compact and easy running. Patent Pending Consistent Drill Times of minutes or less. Utilizes unique Lug design on the top and muleshoe bottom ensuring that the plugs do not spin during drill out. Lug shoe also available. Plugs are set using a universal setting sleeve and shear sleeve adapter. Can be drilled using conventional tubing or coiled tubing. Materials used in construction conducive to a wide range of environments. Slips are only hardened to wicker depth for ease of drill out. Pump Down Wiper available upon request. Express Series Bridge: The Express Series Bridge Plug is converted using a simple composite Bridging Pin that is threaded into the mandrel while sealing in the Inner Diameter. This plugged ID is drilled out before the top slip, thus allowing the upper and lower zones to equalize during drill out. Express Series Ball Drop Frac: After the Ball Drop Frac Plug is set, the inner diameter remains open thus allowing wireline operators to continue work above. A ball is then dropped from the surface and pumped down until it seats on the tool. Once the ball is seated, the operator can pressure up against the Frac Plug. Express Series Caged Ball Frac Plug: Similar to the Ball Drop Frac Plugs, although the Caged Ball Frac Plug houses the ball in the upper ID. This conversion is done using a simple composite Ball Caged adapter. When zonal pressure is greater from below the plug, the ball cage allows the lower and upper zones to comingle. When zonal pressure is greater from above, the ball seats thus isolating the zones. Bridge Ball Drop Caged Ball

Bridge Ball Drop Caged Ball 6k 8k 10k Pump Down Rubber Overall Length Wt. Min Max Tool Operating Range Setting Tool ECFP-4500-000 19.125 9.5-15.1# 3.826 4.09 3.609 6K, 250 Deg Baker #10 / 3 ½" G.O. ECFP-4500-001 22.

2 Bridge Ball Drop Caged Ball 6k 8k 10k Pump Down Rubber Overall Length Wt. Min Max Tool Operating Range Setting Tool ECFP # K, 250 Deg Baker #10 / 3 ½" G.O. ECFP # K, 275 Deg Baker #10 / 3 ½" G.O. ECFP # K, 300 Deg Baker #10 / 3 ½" G.O. ECBP ECBP ECBP # K, 250 Deg Baker #10 / 3 ½" G.O # K, 275 Deg Baker #10 / 3 ½" G.O # K, 300 Deg Baker #10 / 3 ½" G.O. ECFP CB # K, 250 Deg Baker #10 / 3 ½" G.O. ECFP CB # K, 275 Deg Baker #10 / 3 ½" G.O. ECFP CB # K, 300 Deg Baker #10 / 3 ½" G.O. 5 ECFP # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP # K, 300 Deg Baker #10 / Baker #20 / 3 GO 5 ECBP # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECBP # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECBP # K, 300 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP CB # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP CB # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP CB # K, 300 Deg Baker #10 / Baker #20 / 3 GO

Ball Drop Frac Plug Configuration After the Ball Drop Frac Plug is set, the inner diameter remains open thus allowing wireline operators to continue work above.

3 Ball Drop Frac Plug Configuration After the Ball Drop Frac Plug is set, the inner diameter remains open thus allowing wireline operators to continue work above. A ball is then dropped from the surface and pumped down until it seats on the tool. Once the ball is seated, the operator can pressure up against the Frac Plug. The Shear Sleeve Adapter used to set the plugs is designed so that the user can, if needed, run the Drop Ball in place inside the Adapter. This gives the user to choice to utilize the plug as a Flow Back Plug without having to drop the ball from the surface. Ball Drop Overall Length Wt. Min Max Tool Operating Range Setting Tool ECFP ECFP ECFP # K, 250 Deg Baker #10 / 3 ½" G.O # K, 275 Deg Baker #10 / 3 ½" G.O # K, 300 Deg Baker #10 / 3 ½" G.O. 5 ECFP # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP # K, 300 Deg Baker #10 / Baker #20 / 3 GO Accessory 1 11/16" Composite Drop Ball for 4 ½" ECFP Composite Drop Ball for 5 ½" ECFP Pump Down Rubber

Bridge Plug Configuration The Express Series Bridge Plug is converted using a simple composite Bridging Pin that is threaded into the mandrel while sealing in the Inner Diameter.

4 Bridge Plug Configuration The Express Series Bridge Plug is converted using a simple composite Bridging Pin that is threaded into the mandrel while sealing in the Inner Diameter. This plugged ID is drilled out before the top slip, thus allowing the upper and lower zones to equalize during drill out. Bridge Overall Length Wt. Min Max Tool Operating Range Setting Tool ECBP # K, 250 Deg Baker #10 / 3 ½" G.O. ECBP # K, 275 Deg Baker #10 / 3 ½" G.O. ECBP # K, 300 Deg Baker #10 / 3 ½" G.O. 5 ECBP # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECBP # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECBP # K, 300 Deg Baker #10 / Baker #20 / 3 GO Accessory 4 1/2" Composite Bridging Pin ECBP /2" Composite Bridging Pin ECBP /2" Pump Down Wiper

Caged Ball Frac Plug Configuration The Express Series Caged Ball Frac utilizes a simple Ball / Cage Adapter that houses a ¾ Brass Ball in the upper ID of the plug.

5 Caged Ball Frac Plug Configuration The Express Series Caged Ball Frac utilizes a simple Ball / Cage Adapter that houses a ¾ Brass Ball in the upper ID of the plug. When zonal pressure is greater from below the plug, the ball cage allows the lower and upper zones to comingle. When zonal pressure is greater from above, the ball seats thus isolating the zones. Caged Ball Overall Length Wt. Min Max Tool Operating Range Setting Tool ECFP CB # K, 250 Deg Baker #10 / 3 ½" G.O. ECFP CB # K, 275 Deg Baker #10 / 3 ½" G.O. ECFP CB # K, 300 Deg Baker #10 / 3 ½" G.O. 5 ECFP CB # K, 250 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP CB # K, 275 Deg Baker #10 / Baker #20 / 3 GO 5 ECFP CB # K, 300 Deg Baker #10 / Baker #20 / 3 GO Accessory 4 1/2" Composite Caged Ball Assembly ECFP /2" Composite Caged Ball Assembly ECFP /2" Pump Down Wiper

The Shear Sleeve Adapter is placed around the top of the plug and secured using seven steel shear screws while the Setting Sleeve is installed around the Shear Adapter and down to the top slip.

6 Setting Equipment Express Series Plugs are set using a universal Setting Sleeve and Setting Sleeve Adapter. Setting kits are designed to be run on any wireline setting tool or tubing run hydraulic setting tool with either Baker #10, Baker #20 or 3 ½ G.O. connections. The Shear Sleeve Adapter is placed around the top of the plug and secured using seven steel shear screws while the Setting Sleeve is installed around the Shear Adapter and down to the top slip. The Setting Assembly utilizes an Adjuster Nut that mates the directly to the setting tool. The setting sleeve is allowed to be threaded upwards past the Adjuster Nut and secured onto the setting tool. This allows the user to change out plugs on the Sheer Sleeve Adapter without having to remove the setting sleeve. Setting Sleeve Sleeve Adapter Description Overall Length Weld EWST-BK10-ASM-45 Setting Sleeve, 4 ½ on Baker # E4-1 EWST-BK Setting Sleeve Adapter, 4 ½ on Baker # E4-1 EWST-3625-ASM-45 Setting Sleeve, 4 ½ on 3 ½ G.O E4-G EWST Setting Sleeve Adapter, 4 ½ on 3 ½ G.O E4-G EWST-BK10-ASM Setting Sleeve Assembly - 5 on Baker # / 16 E5-1 EWST-BK Shear Sleeve Adapter 5 on Baker # E5-1 EWST-BK20-ASM Setting Sleeve 5 on Baker # / 16 E5-2 EWST-BK Shear Sleeve Adapter 5 on Baker # E5-2 EWST-3625-ASM Setting Sleeve 5 on 3 G.O / 16 E5-G EWST Shear Sleeve Adapter 5 on 3 G.O E5-G ECFP Shear Screws for Shear Sleeve Adapter 9/16 N/A

7 Composite Mutli-Configuration Plugs Use bit and scraper in casing to remove any cement and scale from casing wall before you run any equipment that grips the casing. Before running any plugs in hole, a junk basket and gage ring should be run for the appropriate size casing. Snug the tension sleeve correctly. Do not over tighten. Be sure that nut is tightened correctly. Do not allow the weight of the string to set on the shoe of the plug when setting into well head. Choose correct size plug for casing. Composite Plugs usually cover the complete casing weight range. Install the plug on the setting tool correctly. Do not over tighten. Use correct setting tool size for the plug that you are running. Baker 10 or Go Compact for the 4 ½ and Baker #10, Baker #20 or Go Compact for the 5 ½ or larger. All setting tools should be thoroughly redressed before each run. Be sure that all oil levels are correct for the setting tool/temperature you are running. Use the lock spring on all tools designed for use with a lock spring. Guide the plug through lubricator and rams before setting lubricator in place. If the well has pressure on it, be sure to raise tools to the top of the lubricator before opening well head to pressure. Running speed should be limited to 150 feet per minute. Be extremely careful going into liner tops. If you experience a misfire, do not pull out of hole any faster than 150 feet per minute. Never set plugs in casing collars. Always set plugs in static well conditions. Never perforate any closer than 50 feet to a plug.

Contact Information Poseidon Rentals, LLC 17214 Saddlehorn New Caney, TX 77357

8 Contact Information Poseidon Rentals, LLC Saddlehorn New Caney, TX Account Management D. Wade Maxwell Christina Maxwell

Special Features. u Blanking plug seats in top of. u Bonded seal allows disconnects. and re-connects. u Right-hand or left-hand release

Special Features. u Blanking plug seats in top of. u Bonded seal allows disconnects. and re-connects. u Right-hand or left-hand release DT-2 On/Off Tool The D&L DT-2 On/Off Tool is a tubing seal receptacle allowing isolation of a lower zone using a wireline blanking plug. The tubing string can then be removed from the well. When re-run,