Composite Plugs. Index

Size: px
Start display at page:

Download "Composite Plugs. Index"

Transcription

1

2 Composite Plugs Downhole Isolation Tools - Multi-Stage Operations Index Rapid Mill Ball Drop Rapid Mill Flo-Back Flapper Series (Ball Drop, Bridge, Flo-Back, Flo-Back with Bio-Ball) Mill E-Z Series (Ball Drop, Bridge, Flo-Back, Flo-Back with Bio-Ball) Mill E-Z Pump-Down Plugs Snub Nose Plugs (Ball Drop, Bridge, Flo-Back, Flo-Back with Bio-Ball) Long Range Plugs (Ball Drop, Bridge, Flo-Back, Flo-Back with Bio-Ball) Bio-Ball - Specifications & Instructions Installation Instructions Recommended Running & Drilling Procedures OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA 78405

3 Rapid Mill Ball Drop Frac Plug Innovation Revealed The RAPID MILL composite frac plug uses a ball drop procedure to isolate hydrocarbon formations for multi-stage frac operations. Mostly used for horizontal operations, the slim lightweight design makes deployment fast and efficient in vertical or horizontal wells. After setting, the Rapid Mill remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Comprised of proprietary composite material and having a metallic content, the Rapid Mill can be quickly and easily milled and circulated back to surface using conventional milling, drilling with a rig and tubing, or with coiled tubing. FEatures a No tungsten carbide buttons or aluminum! a Composite mandrel aids in fast drill-outs and time saved. a Consistent drill times of 30 minutes or less a Can be deployed on wireline, coiled tubing, tubing or drill pipe a Designed for horizontal or vertical wells a Dependable cast iron slips secure plug in place a Unique pump down element design requires less fluid and pump pressure to deploy plug horizontally a Setting is done via a universal setting sleeve and adapter. a Positive lock-up feature to ensure lockup of multiple plugs in a single wellbore a Custom O.D. available upon request a Patent Pending Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 1

4 Rapid Mill Ball Drop Frac Plug CONTINUED o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH ball Size setting tool temp/ LOW PSI 4 (101.6) ( ) (88.3) (90.1) (81.0) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) ( ) ( ) ( ) (20.8) ( ) (95.4) (108.6) (118.6) (103.9) (97.2) (115.8) 4.95 (125.7) (90.7) (87.4) (116.8) (109.2) (16.0) (28.7) 24.0 (609.6) 1.5 (38.1) (54.0) Baker #10 Baker #20 8K PSI (55.2MPa) Green Yel Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 2

5 Rapid Mill Flo-Back Flapper Isolation Frac Plug Innovation Revealed The RAPID MILL Flo-Back Flapper composite frac plug is used to isolate hydrocarbon formations for multi-stage frac operations. The slim lightweight design makes deployment fast and efficient in vertical or horizontal wells. Once the Rapid Mill Flo-Back Flapper is set, the flapper closes, aling frac or perf operations above the tool to commence. After operations are complete, topside pressure is released and f is aled through the one-way opening. Comprised of proprietary composite material and having a metallic content, the Rapid Mill can be quickly and easily milled and circulated back to surface using conventional milling, drilling with a rig and tubing, or with coiled tubing. FEatures a No tungsten carbide buttons, and no aluminum! a Consistent drill times of 30 minutes or less a Can be deployed on wireline, coiled tubing, tubing or drill pipe a Flapper spring mechanism is built for horizontal or vertical wells a Dependable cast iron slips secure plug in place a Unique pump down element design requires less fluid and pump pressure to deploy plug horizontally a Setting is done via a universal setting sleeve and adapter. a Positive lock-up feature to ensure lockup of multiple plugs in a single wellbore a Custom O.D. available upon request a Patent Pending Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 3

6 Rapid Mill Flo-Back Flapper Isolation Frac Plug CONTINUED o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH setting tool temp/ LOW PSI 4 (101.6) ( ) (88.3) (90.1) (81.0) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) ( ) ( ) ( ) (20.8) ( ) (95.4) (108.6) (118.6) (103.9) (97.2) (115.8) 4.95 (125.7) (90.7) (87.4) (116.8) (109.2) (16.0) (28.7) 24.0 (609.6) Baker #10 Baker #20 8K PSI (55.2MPa) Green Yel Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 4

7 Series Multi-Configuration Plugs Multi-Stage Operations Innovation Revealed The MAGNUM is a multi-configuration plug used to orarily isolate multi-stage vertical or horizontal completion operations. The base model of the Series is a ball drop configuration. When combined with three additional on-the-fly inserts (Bridge Plug, Flo-Back, or Flo-Back with Bio-Ball), this tool provides the service company with optimum on-site versatility. Comprised of proprietary composite material and having a metallic content, the MAGNUM Series can be quickly and easily milled and circulated back to surface. Ball Drop Bridge Flo-Back Flo-Back w/ Bio-Ball Ball Drop: After setting, the tool remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Bridge: The Bridge Plug, or Kill Plug, has a top venting ability, which als for upper and er equalization during drill out. Flo-Back: When the pressure be the plug is greater than the pressure above, the one-way check valve will al the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug(s) in one trip with conventional milling or drilling tools. Flo-Back with Bio-Ball: Also built with a one-way check valve, this plug orarily prevents sand from invading the upper zone and eliminates cross-f problems by utilizing an Aqueous-Soluble Bio-Ball sealer. After the Bio-Ball has been dissolved by pressure, erature, or fluid, the check valve will al the two zones to commingle. The operator can then independently treat or test each zone and remove the flo-back plug(s) in an under-balanced environment in one trip. FEatures a Consistent drill times of 30 minutes or less a Can be set on wireline, coiled tubing, or production tubing using conventional setting tools a Can be milled or drilled with coiled tubing or a rig a Millable cast iron slips a High differential pressure rating a Top Venting Bridge configuration als for upper & er equalization during drill outs. a Positive lock-up feature to ensure plugs do not spin while milling a Low and high materials conducive to a wide range of environments a Utilizes conventional setting tools a Patented precision shearing device a Setting is done via a universal setting sleeve and adapter. a Unique pump down element design requires less fluid and pump pressure to deploy plug horizontally a Custom O.D. plugs are available upon request a Patent Pending Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 5

8 Series Multi-Configuration Plugs Multi-Stage Operations CONTINUED Ball Drop Bridge Plug Flo-Back Flo-Back with Bio-Ball o.d. 2-7/8 (73.0) 3-1/2 (88.9) 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) 7-5/8 (193.7) casing Specs Plug Specs OPerating Ranges Ball F weight Range min ID max ID O.D. Drop Back Min Min LENGTH ball Size setting MID lb/ft I.D. I.D. tool temp/ (kg/m) LOW PSI ( ) 7.7 (11.5) ( ) (19.3) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) ( ) (59.0) (74.2) (88.3) (95.4) (108.6) 4.67 (118.6) (164.0) (154.8) (171.8) (62.0) (76.0) (90.1) (103.9) (97.2) (115.8) 4.95 (125.7) (166.1) (161.7) (178.4) (54.6) (71.8) (69.2) (63.5) (81.0) (90.7) (87.4) (11.2) (31.8) (116.8) (44.5) (109.2) (151.1) (146.1) (158.8) 2.5 (63.5) (11.2) (12.7) (16.0) 1.0 (25.4) 21.0 (533.4) 26.0 (660.4) 28.0 (711.2) 31 (787.4) (28.6) 1.5 (38.1) (54.0) 2.75 (70.0) Casing Specs are according to API Tubing/Casing Dimension Chart information. Baker #5 Baker #10 Baker #20 Not Yet Available 8K PSI (55.2MPa) Green Yel 300 F (149ºC) HIgh 400 F (204ºC) / Viton OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 6

9 Mill E-Z Temporary Isolation Tools Multi-Stage Operations Innovation Revealed The Mill E-Z Composite Plugs are used for orary isolation in multi-stage vertical or horizontal completion operations. The Mill E-Z line includes the Ball Drop, Bridge Plug, Flo-Back and Flo-Back with Bio-Ball Plugs. Horizontal applications are accomplished with the addition of a Pump Down wiper element. Comprised of proprietary composite material and having a metallic content, the Mill E-Z can be quickly and easily milled and circulated back to surface. Ball Drop Bridge Flo-Back Flo-Back w/ Bio-Ball Mill E-Z Ball Drop: After setting, the tool remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Mill E-Z Bridge: The Bridge Plug, or Kill Plug, has a top venting ability, which als for upper and er equalization during drill out. Mill E-Z Flo-Back: When the pressure be the plug is greater than the pressure above, the one-way check valve will al the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug(s) in one trip with conventional milling or drilling tools. Mill E-Z Flo-Back with Bio-Ball: Also built with a one-way check valve, this plug orarily prevents sand from invading the upper zone and eliminates cross-f problems by utilizing an Aqueous-Soluble Bio-Ball sealer. After the Bio-Ball has dissolved by pressure, erature, or fluid, the check valve will al the two zones to commingle. The operator can then independently treat or test each zone and remove the flo-back plug in an under-balanced environment in one trip. FEatures a Consistent drill times of 30 minutes or less a Can be set on wireline, coiled tubing, or production tubing using conventional setting tools a Utilizes conventional setting tools a Can be milled or drilled with coiled tubing or a rig a Millable cast iron slips a High differential pressure rating a Top Venting Bridge configuration als for upper & er equalization during drill outs. a Low and high materials conducive to a wide range of environments a Positive lock-up feature to ensure plugs do not spin while milling a Patented precision shearing device a Setting is done via a universal setting sleeve and adapter. a Custom O.D. plugs are available upon request a Patent # Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 7

10 Mill E-Z Ball Drop Plug - Multi-Stage Operations Ball drop Drop Plug plug o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH ball Size setting tool temp/ LOW PSI MID HIgh 3-1/2 (88.9) 7.7 (11.5) ( ) (19.3) (74.2) (76.0) (71.8) (69.2) (63.5) (19.1) (444.5) 1.0 (25.4) Baker #5 Not Yet Available 4 (101.6) ( ) (88.3) (90.1) (81.0) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) (95.4) (92.5) (108.6) 4.67 (118.6) (164.0) (154.8) (103.9) (97.2) (92.5) (115.8) 4.95 (125.7) (166.1) (161.7) (90.7) (87.4) (85.7) (34.5) (116.8) (48.3) (109.2) (151.1) (146.1) (63.5) 24.0 (609.6) 1.75 (44.5) (54.0) Baker #10 Baker #20 8K PSI (55.2MPa) Green Yel 300 F (149ºC) 400 F (204ºC) / Viton 7-5/8 (193.7) ( ) (171.8) (178.4) (158.8) Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 8

11 Mill E-Z Bridge Plug - Multi-Stage Operations bridge Bridge plug Plug o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. LENGTH setting tool temp/ LOW PSI MID HIgh 2-3/8 (60.3) 2-7/8 (73.0) 3-1/2 (88.9) 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) 7-5/8 (193.7) 4.7 (7.0) ( ) 7.7 (11.5) ( ) (19.3) ( ) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) ( ) (50.7) (59.0) (74.2) (88.3) (95.4) (92.5) (108.6) 4.67 (118.6) (164.0) (154.8) (171.8) (50.7) (62.0) (76.0) (90.1) (103.9) (97.2) (92.5) (115.8) 4.95 (125.7) (166.1) (161.7) (178.4) (44.5) (54.6) (71.8) (69.2) (63.5) (81.0) (90.7) (87.4) (85.7) (416.1) (444.5) (606.6) (116.8) (604.5) (109.2) (151.1) (146.1) (158.8) 24.0 (609.6) Baker #5 Baker #10 Baker #20 Not Yet Available 8K PSI (55.2MPa) Green Casing Specs are according to API Tubing/Casing Dimension Chart information. Not Yet Available Yel 300 F (149ºC) 400 F (204ºC) / Viton OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 9

12 Mill E-Z Flo-Back Plug (with Bio-Ball Option) Multi-Stage Operations Flo-Back plug Plug o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH setting tool temp/ LOW PSI MID HIgh 2-7/8 (73.0) 3-1/2 (88.9) 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) 7-5/8 (193.7) ( ) 7.7 (11.5) ( ) (19.3) ( ) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) ( ) (59.0) (74.2) (88.3) (95.4) (92.5) (108.6) (118.6) (164.0) (154.8) (171.8) (62.0) (76.0) (90.1) (103.9) (97.2) (92.5) (115.8) (125.7) (166.1) (161.7) (178.4) (54.6) (71.8) (69.2) (63.5) (81.0) (90.7) (87.4) (85.7) (12.7) (16.0) (466.9) (606.6) (116.8) (604.5) (109.2) (151.1) (146.1) (158.8) (22.4) 24.0 (609.6) Baker #5 Baker #10 Baker #20 Casing Specs are according to API Tubing/Casing Dimension Chart information. Not Yet Available 8K PSI (55.2MPa) Green Yel 300 F (149ºC) 400 F (204ºC) / Viton OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 10

13 Mill E-Z Pump-Down Plug - Multi-Stage Operations Innovation Revealed The MILL E-Z PUMP-DOWN PLUGS are utilized mostly for multi-stage horizontal completions. Although all Composite Plugs can be equipped with Pump Down Wipers, the Mill E-Z enables the wireline, guns, CCL, plug and other BHA s to be pumped to a desired depth. Once the depth is reached, MILL E-Z Pump Down Plugs are then set like a conventional bridge plug. Comprised of proprietary composite material and having a metallic content, the Mill E-Z Pump Down Plug can be quickly and easily milled and circulated back to surface using conventional milling, drilling with a rig and tubing, or with coiled tubing. Ball Drop Bridge Flo-Back Flo-Back w/ Bio-Ball Mill E-Z Ball Drop: After setting, the tool remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Mill E-Z Bridge: The Bridge Plug, or Kill Plug, has a top venting ability, which als for upper and er equalization during drill out. Mill E-Z Flo-Back: When the pressure be the plug is greater than the pressure above, the one-way check valve will al the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug(s) in one trip with conventional milling or drilling tools. Mill E-Z Flo-Back with Bio-Ball: Also built with a one-way check valve, this plug orarily prevents sand from invading the upper zone and eliminates cross-f problems by utilizing an Aqueous-Soluble Bio-Ball sealer. After the Bio-Ball has dissolved by pressure, erature, or fluid, the check valve will al the two zones to commingle. The operator can then independently treat or test each zone and remove the flo-back plug in an under-balanced environment in one trip. FEatures a Consistent drill times of 30 minutes or less a Can be pumped to depth at 5 to 8 barrels/min a Designed to be set in horizontal wells on wireline a Millable cast iron slips a Utilizes conventional setting tools a Mill or drill multiple plugs in a single trip a Low and high materials conducive to a wide range of environments a Utilize conventional milling or drilling tools for plug removal a Positive lock-up feature to ensure plugs do not spin while milling a Patented precision shearing device a High differential pressure rating a Custom Plug O.D. available upon request a Patent # OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 11

14 Mill E-Z Pump-Down Ball Drop Plug - Multi-Stage Operations CONTINUED o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH ball Size setting tool temp/ LOW PSI MID HIgh 3-1/2 (88.9) 7.7 (11.5) ( ) (19.3) (74.2) (76.0) (71.8) (69.2) (63.5) (19.1) (444.5) 1.0 (25.4) Baker #5 Not Yet Available 4 (101.6) ( ) (88.3) (90.1) (81.0) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) (95.4) (92.5) (108.6) 4.67 (118.6) (164.0) (154.8) (103.9) (97.2) (92.5) (115.8) 4.95 (125.7) (166.1) (161.7) (90.7) (87.4) (85.7) (34.5) (116.8) (48.3) (109.2) (151.1) (146.1) (63.5) 24.0 (609.6) 1.75 (44.5) (54.0) Baker #10 Baker #20 8K PSI (55.2MPa) Green Yel 300 F (149ºC) 400 F (204ºC) / Viton 7-5/8 (193.7) ( ) (171.8) (178.4) (158.8) Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 12

15 Mill E-Z Pump-Down Bridge Plug - Multi-Stage Operations bridge Bridge plug Plug Bridge Plug o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. LENGTH setting tool temp/ LOW PSI MID HIgh 2-3/8 (60.3) 2-7/8 (73.0) 3-1/2 (88.9) 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) 7-5/8 (193.7) 4.7 (7.0) ( ) 7.7 (11.5) ( ) (19.3) ( ) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) ( ) (50.7) (59.0) (74.2) (88.3) (95.4) (92.5) (108.6) 4.67 (118.6) (164.0) (154.8) (171.8) (50.7) (62.0) (76.0) (90.1) (103.9) (97.2) (92.5) (115.8) 4.95 (125.7) (166.1) (161.7) (178.4) (44.5) (54.6) (71.8) (69.2) (63.5) (81.0) (90.7) (87.4) (85.7) (416.1) (444.5) (606.6) (116.8) (604.5) (109.2) (151.1) (146.1) (158.8) 24.0 (609.6) Baker #5 Baker #10 Baker #20 Not Yet Available 8K PSI (55.2MPa) Green Casing Specs are according to API Tubing/Casing Dimension Chart information. Not Yet Available Yel 300 F (149ºC) 400 F (204ºC) / Viton OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 13

16 Mill E-Z Pump-Down Flo-Back Plug (with Bio-Ball Option) Multi-Stage Operations Flo-Back plug Plug o.d. casing Specs Plug Specs OPerating Ranges weight Range lb/ft (kg/m) min ID max ID O.D. I.D. LENGTH setting tool temp/ LOW PSI MID HIgh 2-7/8 (73.0) 3-1/2 (88.9) 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) 7 (177.8) 7-5/8 (193.7) ( ) 7.7 (11.5) ( ) (19.3) ( ) ( ) ( ) ( ) ( ) (20.8) ( ) ( ) ( ) ( ) (59.0) (74.2) (88.3) (95.4) (92.5) (108.6) (118.6) (164.0) (154.8) (171.8) (62.0) (76.0) (90.1) (103.9) (97.2) (92.5) (115.8) (125.7) (166.1) (161.7) (178.4) (54.6) (71.8) (69.2) (63.5) (81.0) (90.7) (87.4) (85.7) (12.7) (16.0) (466.9) (606.6) (116.8) (604.5) (109.2) (151.1) (146.1) (158.8) (22.4) 24.0 (609.6) Baker #5 Baker #10 Baker #20 Casing Specs are according to API Tubing/Casing Dimension Chart information. Not Yet Available 8K PSI (55.2MPa) Green Yel 300 F (149ºC) 400 F (204ºC) / Viton OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 14

17 Snub Nose Low Temp/Low Pressure Plug Innovation Revealed The SNUB NOSE composite frac plug is a multi-configuration plug used to orarily isolate multi-stage vertical or horizontal completion operations. The base model of the Snub Nose is a ball drop configuration. When combined with three additional on-the-fly inserts (Bridge Plug, Flo-Back, or Flo-Back with Bio-Ball), this tool provides the service company with optimum on-site versatility. Comprised of proprietary composite material and having a metallic content, the Snub Nose can be quickly and easily milled and circulated back to surface. Ball Drop Bridge Flo-Back Flo-Back w/bio-ball Snub Nose Ball Drop: After setting, the tool remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Snub Nose Bridge: The Bridge Plug, or Kill Plug, has a top venting ability, which als for upper and er equalization during drill out. Snub Nose Flo-Back: When the pressure be the plug is greater than the pressure above, the one-way check valve will al the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug(s) in one trip with conventional milling or drilling tools. Snub Nose Flo-Back with Bio-Ball: Also built with a one-way check valve, this plug orarily prevents sand from invading the upper zone and eliminates cross-f problems by utilizing an Aqueous-Soluble Bio-Ball sealer. After the Bio-Ball has been dissolved by pressure, erature, and fluid, the check valve will al the two zones to commingle. The operator can then independently treat or test each zone, remove the flo-back plug(s) in an under-balanced environment, all in one trip. FEatures a No tungsten carbide buttons or aluminum! a Composite mandrel aids in fast drill-outs and time saved. a Consistent drill times of 15 minutes or less a Can be deployed on wireline, coiled tubing, tubing or drill pipe a Designed for horizontal or vertical wells a Dependable patented cast iron slips secure plug in place a Unique pump down element design requires less fluid and pump pressure to deploy plug horizontally a Setting is done via a universal setting sleeve and adapter. a Positive lock-up feature to ensure lockup of multiple plugs in a single wellbore a Custom O.D. available upon request a Patent Pending Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 15

18 Snub Nose Low Temp/Low Pressure Plug CONTINUED Ball Drop Bridge Plug Flo-Back Flo-Back w/bio-ball o.d. 4 (101.6) 4-1/2 (114.3) 5 (127.0) 5-1/2 (139.7) casing Specs weight Range lb/ft (kg/m) ( ) ( ) ( ) ( ) (20.8) ( ) min ID (88.3) (95.4) (108.6) (118.6) max ID (90.1) (103.9) (97.2) (115.8) 4.95 (125.7) O.D (81.0) (90.7) (87.4) (116.8) (109.2) Ball Drop Min I.D (12.7) Plug Specs F Back Min I.D (7.1) LENGTH 20.0 (508.0) 21.0 (533.4) ball Size 1.5 (38.1) 1.5 (38.1) setting tool Baker #10 Baker #10, #20 OPerating Ranges 6K PSI (41.4MPa) Green Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 16

19 Long Range Slim Plug with Wider Range Capabilities Innovation Revealed The Long Range composite frac plug is s latest offering to enable operators to isolate wellbores in challenging applications. Because of the tool s slim outer diameter and expansive reach, The Long Range can pass through damaged casing, restricted internal casing diameters, or existing casing patches in the well bore. This tool can be set on wireline or coiled tubing. Comprised of proprietary composite materials, The Long Range also features dependable cast iron slips, superior element sealing package, and a rigid core to ensure the plug passes through the toughest of conditions. This plug is available in all the foling configurations: Ball Drop, Bridge Plug, Flo-Back, and F-Back with Bio-Ball. Ball Drop Bridge Flo-Back Flo-Back w/ Bio-Ball Long Range Ball Drop: After setting, the tool remains open for fluid f and als wireline services to continue until the ball drop isolation procedure has started. Once the surface-dropped ball is pumped down and seated in to the inner funnel top of the tool, the operator can pressure up against the plug to achieve isolation. Long Range Bridge: The Bridge Plug isolates the wellbore in both directions and has a top venting ability, which als for upper and er equalization during drill out. Long Range Flo-Back: When the pressure be the plug is greater than the pressure above, the one-way check valve will al the two zones to commingle. The operator can independently treat or test each zone and then remove the flo-back plug(s) in one trip with conventional milling or drilling tools. Long Range Flo-Back with Bio-Ball: Also built with a one-way check valve, this plug orarily prevents sand from invading the upper zone and eliminates cross-f problems by utilizing an Aqueous-Soluble Bio-Ball sealer. After the Bio-Ball has been dissolved by pressure, erature, or fluid, the check valve will al the two zones to commingle. The operator can then independently treat or test each zone and remove the flo-back plug(s) in an under-balanced environment in one trip. FEatures a No tungsten carbide buttons! a Can be deployed on wireline or coiled tubing a Designed for horizontal or vertical wells a Unique pump down element design requires less fluid and pump pressure to deploy plug horizontally a Dependable cast iron slips secure plug in place a Setting is done via a universal setting sleeve and adapter. a Positive lock-up feature to ensure lockup of multiple plugs in a single wellbore a Custom O.D. available upon request a Patent Pending Pump Down Wipers Available for Horizontal Applications OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 17

20 Long Range Slim Plug with Wider Range Capabilities CONTINUED Ball Drop Bridge Plug Flo-Back Flo-Back with Bio-Ball casing Specs Plug Specs OPerating Ranges Ball o.d. min ID max ID O.D. Drop Min LENGTH ball Size setting MID I.D. tool temp/ LOW PSI HIgh 4-1/2 (114.3) 5-1/2 (139.7) (88.9) (111.1) (108.6) (125.7) (82.6) 4.04 (103.1) (12.7) (38.1) 32.0 (812.8) 29.4 (746.8) 1.5 (38.1) (54.0) Owen 2-1/8" or 3-1/4" Multi-Stage 8K PSI (55.2MPa) Green Yel 300 F (149ºC) 400 F (204ºC) / Viton Casing Specs are according to API Tubing/Casing Dimension Chart information. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 18

21 Flo-Back with Bio-Ball - All Plugs Bio-Ball Specifications Appearance: Spherical, Opaque Compositions: PEO, PPO, PLA Specific Gravity: 1.18 Mechanical Integrity: Up to 5000 psi at 230ºF (34.5MPa at 110ºC) after 1 hour of exposure at erature Applications Range: 250ºF to 350ºF (121ºC to 177ºC) Compatible Fluids: Polar Solvents: e.g. Water, brine, short chain alcohols Incompatible Fluids: Non-Polar Solvents: e.g. Diesel, Benzene, Xylene, kerosene, Toluene Technical Considerations: Wet the Bio-Balls in Mineral oil prior to placement in the ball injector to avoid clumping. Do not expose to heat eratures greater than 180ºF (82ºC). Avoid contact with water or other polar solvents during storage. 1 Solubility behavior of BioBalls HR under various testing conditions. All tests were performed at 500 psi (3.5MPa). 0.9 Diameter (in) % KCI 250F 15% HCI 250F 25% HCI 250F 2% KCI 300F (149ºC) 15% HCI 300F (149ºC) 25% HCI 300F (149ºC) Time (hrs) OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 19

22 Installation of MILL E-Z, MAGNUM Series, OR RAPID MILL Composite Plug Prior to running a Mill E-Z, MAGNUM Series, or RAPID MILL Composite Plug on wireline, it is recommended that a junk basket and gauge ring larger than the OD of the plug, and less than the drift of the casing, should be ran. A depth of greater than the setting depth of the bridge plug is desired. If any obstruction is encountered in the casing, additional runs should be made to recover obstruction or an alternate casing cleanup process considered. Ensure the wireline setting tool has the appropriate amount of oil according to the erature at the Plug s setting depth. It is preferable to use a S Set Power Charge in the setting tool. Make sure all connections on the setting tool are tight. Hand tighten the Mill E-Z, MAGNUM Series, RAPID MILL, or SNUB NOSE Composite Plug setting sleeve onto the setting tool. For the Mill E-Z, MAGNUM Series, or SNUB NOSE, screw the adapter mandrel into the Mill E-Z Composite Plug and use a small pipe wrench when tightening the adapter mandrel into the aluminum mandrel of the plug. *NOTE: Do not tighten across shear groove. Slightly more than hand tightened is sufficient. For the Mill E-Z or MAGNUM Series 2-3/8", 2-7/8", or 3-1/2" (60.3mm, 73.0mm, or 88.9mm) apply thread tape to upper thread of adapter mandrel. This will prevent the adapter mandrel from falling into the well bore while coming out of the hole. For the Mill E-Z, MAGNUM Series, or SNUB NOSE 4", 4-1/2", 5-1/2", 7", 7-5/8", 8-5/8" or 9-5/8" (101.6mm, 114.3mm, 139.7mm, 177.8mm, 193.7mm, 219.0mm or 244.5mm) apply torsion spring to upper thread of adapter mandrel. This will prevent the adapter mandrel from falling into the well bore while coming out of the hole. For the RAPID MILL Composite Plug, apply included LOCTITE to the bottom threads on the adapter mandrel. Then, thread adapter mandrel in to the brass shear sub in the bottom of the RAPID MILL Composite Plug. Visually inspect the bottom of the RAPID MILL Composite Plug to insure the adapter mandrel is bottomed out in the brass shear sub. Guide the bridge plug and adapter mandrel into the setting sleeve and into the setting tool. Rotate clockwise until the mandrel threads are fully engaged. It is not necessary to use a pipe wrench when tightening the adapter mandrel and plug into the setting tool. Firmly hand tightened is sufficient. Rotate the setting sleeve toward the plug until it has come into contact with the top of the bridge plug. Make sure there are no gaps between the top of the plug and the bottom of the setting sleeve. Also insure there is sufficient thread engagement between the setting sleeve and the setting tool. No more than 2 threads of the setting tool should be visible. Fs Setting Tools, rotate the jam nut down to the setting sleeve and tighten the jam nut to the setting sleeve with a pipe wrench. Tighten the set screw on the setting sleeve in to the setting tool. Now, the tool is ready to run in the hole. NOTE: If the air gap cannot be eliminated, the setting tool should be disassembled and inspected. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 20

23 Running the MILL E-Z, MAGNUM Series, OR RAPID MILL Composite Plug in a vertical well Once the length of the CCL to the top of the plug has been determined, pick up the setting tool and Mill E-Z, MAGNUM Series, RAPID MILL, or SNUB NOSE Plug assembly with wireline. NOTE: For best results, DO NOT support the weight of the tool string by the bridge plug. Support the weight by handling the setting tool itself. Precaution should be used once the assembly is suspended as to not let the plug swing into valves or pressure lines thus causing damage or injury to the plug and employees. NOTE: Hitting fluid level or a sand bridge at a rapid speed could prematurely set the bridge plug! We recommend a line speed of ser than 100 (30.5m) per minute when hitting the fluid level. A line speed of approx. 200 per minute (61.0m) is recommended of a wellbore full of fluid. Certain conditions may warrant a less rapid descent or an increased rate of speed. Once the setting depth is achieved, set the plug and note any weight loss of the assembly on the wireline truck weight indicator. In some cases there may not be a positive indication that the plug is set. Pick up the setting assembly approx. 20 to 30 (6.1m to 9.1m) and note any weight loss or CCL movement. *Ample cement or sand may be used on the top of the plug to help absorb the percussion generated by the perforating guns. *Do not perforate within 75 (22.9m) of the plug after it is set. Disassemble the setting equipment from the setting tool. CAUTION: When testing the plug sly fill hole with fluid so as not to hydraulically hammer the plug down the hole with the column of fluid. Recommended pump rate is ¼ to ½ bbl/min for the first 30 minutes, then sly increase pump pressure to fill wellbore, to ensure a sufficient fluid cushion. Running the MILL E-Z, MAGNUM Series, OR RAPID MILL Composite Plug in a Horizontal well Once the length of the tool string has been determined, pick up the perforating guns, CCL, setting tool, and MILL E-Z, MAGNUM Series, Rapid Mill, or SNUB NOSE Composite Plug assembly with wireline. For best results, do not support the weight of the setting tool, CCL and plug by the plug. Support the weight by handling the setting tool itself. Precaution should be used once the assembly is suspended as to not let the plug swing into valves or pressure lines thus causing damage or injury to the plug and employees. When running the plug in the well, a line speed of 200 (61.0m) per minute or less is desirable in the vertical section of the well. Certain conditions may warrant a ser or faster descent. 1. While paying close attention to line tension, s down line speed to approx. 150 (45.7m) per minute when approaching the 30 degree kickoff point. 2. Start pumping fluid at a barrel a minute after tie in. 3. Increase pump pressure and rate to 2.0 BPM. 4. As deviation increases, you will sly increase pump pressure and fluid rate to 4 BPM, to 6 BPM, then 8 BPM, etc. Make sure to space out pressure and fluid rate increases as not to hit BHA with sudden force. Do not exceed 15 BPM or 5,000 psi (34.5MPa) of pump pressure at any time during the pump down process. It is not recommended to exceed 225 ft.(68.6m)/min. 5. Approximately 200 ft (61.0m) from desired set depth, s line speed to under 100ft (30.5m)/min to al line to become fully taut. 6. Once desired depth has been reached, shut down pumps. 7. Fire setting tool and al sufficient time to pass before picking up wireline. To disassemble the setting equipment from the setting tool, hold back-ups on the setting tool, rotate the setting sleeve loose, and remove the adapter mandrel from the inside of the setting sleeve. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 21

24 Recommended Coiled Tubing Drilling/Milling Procedures For The Mill E-Z, MAGNUM SERIES and RAPID MILL Composite Plugs The foling Bottom Hole Assembly is recommended to remove the Mill E-Z, MAGNUM Series, RAPID MILL, or the SNUB NOSE Composite plug. Tri-Cone Sealed Bearing Bit or 5-Bladed Concave Junk Mill (95-98% of Drift Diameter) Hi Torque Mud Motor Hydraulic Disconnect Dual Back Pressure Valve Coiled Tubing Connector Enough Coil Tubing to reach bottom of well The foling is a recommended drilling/milling procedure for removing and eliminating one or multiple Mill E-Z, MAGNUM Series, RAPID MILL, or SNUB NOSE Composite Plugs from the well bore. Check to ensure all equipment is compatible and all running procedures are well within manufactures recommended guidelines. 1. Move in Coiled Tubing Equipment (It is recommended to have a Double Pump Truck spot the equipment. 2. Have a safety briefing to cover the rig up procedures 3. Rig up Coiled Tubing Equipment and enough lubricator to cover the bottom hole assembly, motor and the Mill. 4. Function test the BOP s with the coiled tubing crew. 5. Run Coil Tubing through the coiled tubing stack until pipe comes out of the lubricator. 6. Mic the coiled tubing to ensure the correct O.D. and no egg-shaping of the coiled tubing. 7. Straighten the coil and cut the bottom of the coil off. File the flared end of the coil to bevel the end of it. (This helps from cutting o-rings and damaging slips when making up the coil). 8. Make up the coil connector with a pull tester plate. Pull test the coil connector to manufactures recommended pull weight. NOTE: When pull testing the coil connector measure off the hydraulics, then compare it to the weight indicator to adjust the weight indicator if it is off. 9. Run the coil out of the lubricator and check the make on the coil. Retighten the coil connector and make up the set screws. 10. Load and circulate the coiled tubing with fluid until the fluid comes out clean. NOTE: Recommended to run in line filter with a screen. 11. Make up the dual back pressure valve, hydraulic release, and hi-torque motor with the recommended mill or bit. Test the motor at surface by drilling a test hole. 12. Rig up on the well and test. 13. Run in the hole, pumping through the motor at the minimum rate checking pick up and run in weights. 14. Approximately 1,000 (304.8m) before the perfs bring the pump rate up on the motor to the manufacturer s recommended rate (approx. 400 to 600 rpm). 15. Pump a dyed gel sweep. 16. Approximately 100 (30.5m) before the perfs depth establish the f rate in the return tank. The optimum rate is 1 bbl in / 1 bbl out. NOTE: The bbl for bbl rate will also depend on the pressures be the plug from the pressures from the open perfs. This will determine on how much back pressure to hold. If there is a possibility of drilling through higher a differential (after running the coil through the perfs, while staying off the plug) it would be necessary to clean out the well bore before drilling out the plug, this will eliminate the possibilities of sticking the coil. 17. After the rates and wellbore differentials are stable, run in the hole no more than 5.0 ft (1.5m) / min. watching the weight indicator. When you see about 200lbs to 500lbs (90.7Kgs to 226.8Kgs) of weight loss, let the coil unit creep in the hole about 0.1 to 0.3 ft (.03m to.09m)/min. watching for any pump pressure increases or continuation of weight loss. (No more than 1,000 lbs. [453.6Kgs]). Once you see the pump pressure increase 100 lbs. to 300 lbs. (45.4Kgs to 136.1Kgs) differential, set the brake to gain weight back to normal pump pressure. Release brake continuing the milling operations until string weight and pump pressure is regained (if you are taking a gas kick, it is recommended to pick up above the perfs and circulate the well until the pump rate and wellhead pressure is maintained and the weight on the coil is ok). OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 22

25 Recommended Coiled Tubing Drilling/Milling Procedures (Continued) 18. After the plug has been milled through, pump 10 bbl gel sweep with dye pumping 5 bbl gel and 5 bbl KCL water, then 5 bbl gel and continue to the desired depth. 19. For multiple plugs, continue drill-out procedures form step 14. NOTE: Each stage will have different bottom hole pressures which will determine on what needs to be held on the backside. Pumping gel sweeps before and after drilling the plug and circulating well clean before each stage will help from sticking the coiled tubing. NOTE: It is preferred to take a less aggressive approach and mill or grind the plug into small pieces to minimize debris size for particle management. Recommended Tubing Drilling Procedures For The Mill E-Z Composite Plugs The foling Bottom Hole Assembly is recommended to remove the Mill E-Z, MAGNUM Series, RAPID MILL, or SNUB NOSE Composite Plug. Tri-Cone Sealed Bearing Bit or 5-Bladed Concave Junk Mill (95-98% of Drift Diameter) Bit Sub or Pump-Off Bit Sub Power Swivel Enough Tubing to reach bottom of well The foling is a recommended drilling procedure for removing and eliminating Mill E-Z Composite Bridge Plugs from the well bore. Check to ensure all equipment is compatible and all running procedures are well within manufactures recommended guidelines. 1. Rig up bit sub and bit/mill to end of tubing. 2. Run assembly to bottom and tag cement or plug lightly. 3. Pick up 4-6 feet ( m) off Mill E-Z, MAGNUM Series, RAPID MILL, or SNUB NOSE Composite Plug or cement. 4. Keep the pressure and pump rate approximately ft ( m)/min annular f, Approx 2 bbls/min. 5. Start turning power swivel and bring tubing rpm. 6. Sly er bit assembly into hole until pump pressure increases or set down weight decreases. 7. Begin feathering the plug for the first few minutes to mill up the upper portion of the mandrel. 8. While drilling note any increase in pressure from the well due to the plug equalizing. 9. Pick up drill assembly to circulate the debris off the top of the plug. 10. Proceed to feathering the plug for the next few minutes while setting appox. 2,000 lbs (907.2Kgs) of tubing weight on the plug. 11. After drilling out the upper portion of the plug, pick up the tubing string 5 (1.5m) to al er zone to equalize and circulate debris. 12. Continue drilling operation until string weight and pump pressure is regained. 13. Chase the bottom of the plug to the bottom of the well or the top of the next plug. 14. Shut down the pumps. 15. For multiple plugs return to step 7 before shutting down the pumps. 16. The bottom section of the first plug will increase your drill time ever so slightly. NOTE: It is preferred to drill or grind the plug into small pieces to minimize debris size for particle management. OilTools.com 5655 Bear Lane, Suite 100, Corpus Christi, TX USA Page 23

26 Revision Date: January 13, 2010

Express Series Multi Configuration Composite Body Bridge / Frac Plugs

Express Series Multi Configuration Composite Body Bridge / Frac Plugs Multi Configuration Composite Body Bridge / Frac Plugs The Express Series Bridge and Frac Plugs utilize a unique combination of composites to provide a dependable, durable, and cost-efficient method for

More information

DSI THRU-TUBING INC. Bear Claw Composite Bridge & Frac Plug Systems. Proof in Performance

DSI THRU-TUBING INC. Bear Claw Composite Bridge & Frac Plug Systems. Proof in Performance DSI THRU-TUBING INC Bear Claw Composite Bridge & Frac Plug Systems Proof in Performance Proof in Performance www.dsithrutubing.com CANADA Toll Free Dispatch 855-346-9788 3300, 205 5th Ave SW Calgary T2P

More information

Drilling & Down-hole Completion Tools

Drilling & Down-hole Completion Tools HYDRAULIC SET PRODUCTION PACKER MODEL: WC-HP-1 & WC-HPL-1[Large Bore] PRODUCT No.: WC-20101 & WC-20112 HP-1 is an industry standard, fully hydrostatic, hydraulic set and shear release single string retrievable

More information

Completion Tools Catalog

Completion Tools Catalog Completion Tools Catalog www.teamoiltools.com 2012 TEAM Oil Tools. All rights reserved. www.teamoiltools.com 2012 TEAM Oil Tools. All rights reserved. TABLE OF CONTENTS P/N Description Page P/N Description

More information

Completion Solutions Inc.

Completion Solutions Inc. Completion Solutions Inc. Simple Designs That Simply Work! Company Introduction Dec 2012 1 Who is Completions Solutions Inc? Founded in 2012 Focused on efficient and economical well bore stimulation (both

More information

TMK QUANTUM Infinity. Unlimited Stage Fracturing System COMPLETIONS

TMK QUANTUM Infinity. Unlimited Stage Fracturing System COMPLETIONS TMK QUANTUM Infinity Unlimited Stage Fracturing System COMPLETIONS TMK QUANTUM Infinity TMK QUANTUM Infinity ball-actuated sliding sleeve system utilizes a revolutionary, patent pending electronic counter

More information

Intervention Barriers

Intervention Barriers Intervention Barriers A barrier is defined as a means of containing wellbore pressure and fluids. Two effective barriers are required for most intervention operations. Consider when barriers are effective

More information

Special Features. u Blanking plug seats in top of. u Bonded seal allows disconnects. and re-connects. u Right-hand or left-hand release

Special Features. u Blanking plug seats in top of. u Bonded seal allows disconnects. and re-connects. u Right-hand or left-hand release DT-2 On/Off Tool The D&L DT-2 On/Off Tool is a tubing seal receptacle allowing isolation of a lower zone using a wireline blanking plug. The tubing string can then be removed from the well. When re-run,

More information

Service Tools Catalog

Service Tools Catalog Service Tools Catalog www.teamoiltools.com 2012 TEAM Oil Tools. All rights reserved. www.teamoiltools.com 2012 TEAM Oil Tools. All rights reserved. TABLE OF CONTENTS P/N Product Description Page Type P

More information

Product Overview Last date of Revision:

Product Overview Last date of Revision: Product Overview Last date of Revision: 07-07-2018 Gryphon Oilfield Solutions is a worldwide provider of quality, value driven, oilfield products and services. We specialize in aggressive well completions

More information

Casing Scraper. Service Equipment. Features

Casing Scraper. Service Equipment. Features Casing Scraper The Casing Scraper is a spring type, mechanical casing scraper, featuring a large by-pass area between the blades to allow circulation of debris. The body is constructed of the highest quality

More information

Full Flow Reverse Circulation Junk Baskets. Manual B320

Full Flow Reverse Circulation Junk Baskets. Manual B320 Full Flow Reverse Circulation Junk Baskets Manual B320 CONTENTS Logan Full Flow Reverse Circulation Junk Basket Overview... 2 Uses... 2 Construction... 2 Tool Illustration... 3 Operation... 4 Recovering

More information

8/28/13: Luchini and Mertz Land Surveying Company staked location. DC: $3,250 TDC: $3,250

8/28/13: Luchini and Mertz Land Surveying Company staked location. DC: $3,250 TDC: $3,250 DAKOTA RESOURCES, INC. UNIVERSITY KATELYN #3 467 FWL & 800 FNL SEC. 6, BLK. 30 CRANE CO., TX API #: 42-103-36244 Proposed TD: 9400 AFE: $1,704,475.00 PROP: 346-3 PERMIT #: 769425 8/28/13: Luchini and Mertz

More information

Pipe Recovery Equipment

Pipe Recovery Equipment Pipe Recovery Equipment Jet Research Center offers a variety of field-proven, reliable pipe recovery equipment to satisfy the high demands in the oilfield industry. The equipment supplied by JRC undergoes

More information

MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES

MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES MOTION DECOUPLED HYDRAULIC DELIVERY SYSTEM (MDHDS) ASSEMBLY AND DEPLOYMENT PROCEDURES Prepared for the University of Texas by Pettigrew Engineering, PLLC Tom Pettigrew, PE President Revision: 5 15 October

More information

Thru-Tubing. Motors and standard tools

Thru-Tubing. Motors and standard tools Thru-Tubing Motors and standard tools Thru-Tubing Reliable. Innovative. Premium. We are proud of our products and their contribution to the downhole drilling and thru-tubing industries. Research Innovate

More information

Coiled Tubing Tool EXTERNAL SLIP CONNECTOR. Feature. Specification Tool O.D. inch. Coiled Tubing O.D. inch. Tool I.D. inch. Conn.

Coiled Tubing Tool EXTERNAL SLIP CONNECTOR. Feature. Specification Tool O.D. inch. Coiled Tubing O.D. inch. Tool I.D. inch. Conn. Coiled Tubing Tool EXTERNAL SLIP CONNECTOR The External Slip Connector is designed through a unique non-rotational slip, the upper end is connected with the coiled tubing, and the lower end is connected

More information

COILED TUBING TOOLS SALE RENTAL - LEASE

COILED TUBING TOOLS SALE RENTAL - LEASE COILED TUBING TOOLS SALE RENTAL - LEASE GTECH Energy Services LLC 67 Pinepath Pl. Spring, Texas 77381 PH: 713-703-2959 Fax: 713-510-1802 sales@gtechenergyservices.com SALES@GTECHENERGYSERVICES.COM 1 PRODUCT

More information

The Well Commander Mitigate drilling hazards with the industry s most versatile drilling valve. Todd Gooding Business Development Manager

The Well Commander Mitigate drilling hazards with the industry s most versatile drilling valve. Todd Gooding Business Development Manager The Well Commander Mitigate drilling hazards with the industry s most versatile drilling valve Todd Gooding Business Development Manager WELL COMMANDER A COMPLETE redesign of the ball-activated Centurion

More information

Short Fast Strong.

Short Fast Strong. Short Fast Strong www.downholetechnology.com Designed and Manufactured for Speed and Reliability During Frac Operations Boss Hog frac plugs are short, fast and strong. More than 35,000 Boss Hog plugs have

More information

Dynamic MDT Service Packer V-III Un-Loader Valve ANC Storm Valve

Dynamic MDT Service Packer V-III Un-Loader Valve ANC Storm Valve Dynamic MDT Service Packer V-III Un-Loader Valve ANC Storm Valve Dynamic MDT Service Packer Dynamic MDT Retrievable Packer consists of a compression set packer with hydraulic hold down that is designed

More information

WLTC Retrievable Bridge Plug

WLTC Retrievable Bridge Plug service Tools WLTC Retrievable Bridge Plug The WLTC Retrievable Bridge Plug is designed to perform all tasks normally required of a tubing run packer-type bridge plug and can be quickly converted to run

More information

Casing Cementation Equipment

Casing Cementation Equipment Casing Cementation Equipment Float Equipment Cementing Plugs Casing Centralizers Stage Tools Inflatable Casing Packers Extended Reach Casing Equipment Swellable Casing Packers Liner Equipment Quality Control/Assurance

More information

Tryton. Tool Services. People. Products. Performance. Canadian Locations

Tryton. Tool Services. People. Products. Performance. Canadian Locations Tool Services Canadian Locations Lloydminster - Corporate Office 6702-56 Street Lloydminster, AB T9V 3A7 Ph: 780 875-0800 (24hr) Brooks - Field Office 329-9th St. E Brooks, AB T1R OK2 Ph: 403 362-8600

More information

2013 Latin America Perforating Symposium. SLAP-23 Perforating Options Available Today in Horizontal Shale Oil and Gas Wells. Kerry Daly, Weatherford

2013 Latin America Perforating Symposium. SLAP-23 Perforating Options Available Today in Horizontal Shale Oil and Gas Wells. Kerry Daly, Weatherford 2013 Latin America Perforating Symposium Perforating Options Available Today in Horizontal Shale Oil and Gas Wells Kerry Daly, Weatherford Typical Eagle Ford Well Costs Total well cost approximately $10

More information

SERVICE TOOLS. Magnus MDT Service Packer V-III Un-Loader Valve MANC Storm Valve

SERVICE TOOLS. Magnus MDT Service Packer V-III Un-Loader Valve MANC Storm Valve s ervice packers Magnus MDT Service Packer V-III Un-Loader Valve MANC Storm Valve Magnus MDT Service Packer Magnus MDT Retrievable Packer consists is a compression set packer with hydraulic hold down that

More information

#10 Setting Tool Assembly Product Family No (10)

#10 Setting Tool Assembly Product Family No (10) BRICO Oil Tools provides a dependable line of Wireline Pressure Setting Tools for the Wireline industry worldwide. Our engineering, high quality and service provides a cost effective alternative. BT#10

More information

T-2 On-Off Tool. Available with all common wireline profiles, the stinger works with industrystandard blanking plugs, standing valves and regulators.

T-2 On-Off Tool. Available with all common wireline profiles, the stinger works with industrystandard blanking plugs, standing valves and regulators. T-2 On-Off Tool Classic Oilfield s T-2 On-Off Tool enables the tubing string to be disconnected above a packer for zonal isolation, tubing retrieval, and temporary zone abandonment. The tool contains an

More information

Health, Safety and Environment: Product Performance: Proven Quality: Presence: Client Focus: Tried and Tested:

Health, Safety and Environment: Product Performance: Proven Quality: Presence: Client Focus: Tried and Tested: Wenzel Downhole Tools is the leading motor and drilling tool supplier, with worldwide operations supporting the oilfield and construction industries. Wenzel s capability to engineer, manufacture and service

More information

Oiltools main product lines

Oiltools main product lines Archer Oiltools What we will cover The road from Seadrill to Archer The Well Company Services that Archer provide Archer s Global Footprint Archer Oiltools Global Footprint Archer Oiltools - What we do

More information

DRILLING MOTOR HANDBOOK

DRILLING MOTOR HANDBOOK DRILLING MOTOR HANDBOOK GORILLA Drilling Motors TM rev213.6.19 DRILLING MOTOR HANDBOOK www.axonep.com The information contained in this handbook is for reference only. AXON Downhole Products Inc. does

More information

Downhole Tools Worldwide.

Downhole Tools Worldwide. Downhole s Worldwide. INFLATABLES PRODUCTION PACKER SEV-SET PACKER THRU TUBING PACKER CASING PACKER STRADDLE PACKER HYDRAULIC DISCONNECT ON-OFF SEAL Table of Contents 1-1 1-2 1-3 1-4 1-5 1-6 1-7 TechWest

More information

HYDRAULIC WORKOVER SERVICES

HYDRAULIC WORKOVER SERVICES HYDRAULIC WORKOVER SERVICES Technology at work for you. Cudd Energy Services (CES) offers a diversified portfolio of solutions for today s well challenges. From a simple completion job to a complex well

More information

Delivering innovation through engineering

Delivering innovation through engineering Delivering innovation through engineering +44 1224 727480 Completions & Work-over Operations Bore Selector gives access to either the main production bore or annulus in a traditional vertical xmas tree,

More information

ISOLATION/UNIVERSAL TOOLS

ISOLATION/UNIVERSAL TOOLS ISOLATION/UNIVERSAL TOOLS stingercanada.com Grande Prairie 11303 96 Avenue Grande Prairie, AB T8V 5M3 780-513-3696 Calgary 420-510 5th Street SW Calgary, AB T2P 3S2 403-340-0716 Red Deer 334-28042 Hwy

More information

Atlas Copco Oil and Gas Rigs. The Predator Advantage

Atlas Copco Oil and Gas Rigs. The Predator Advantage Atlas Copco Oil and Gas Rigs The Predator Advantage Atlas Copco Drilling Solutions Leading supplier globally of rotary drilling equipment Three manufacturing locations Garland, Texas, USA Nasik, India

More information

02/01/2013: Surveying, Luchinni & Mertz, University Emilie #3R well to be drilled. DWC: $1, CTD: $1,500.00

02/01/2013: Surveying, Luchinni & Mertz, University Emilie #3R well to be drilled. DWC: $1, CTD: $1,500.00 DAKOTA RESOURCES UNIVERSITY EMILIE #3R 560 FEL & 1680 FSL, SEC. 35, BLK. 4 ANDREWS CO., TX API 42-003-45115 TD: 11,200 AFE: 377 PROP: 000307 PERMIT: 756090 02/01/2013: Surveying, Luchinni & Mertz, University

More information

Set, seal, and retrieve with confidence. Packers Catalog

Set, seal, and retrieve with confidence. Packers Catalog Set, seal, and retrieve with confidence Packers Catalog 1 2 Table of Contents Conventional Packers...05 ESP/Dual Completion Packers...35 High-Rate-Gas Packers...43 HPHT Packers...47 Intelligent Completion

More information

PRODUCTION HYDRAULIC PACKER FIELD TEST

PRODUCTION HYDRAULIC PACKER FIELD TEST DOE/RMOTC/020120 PRODUCTION HYDRAULIC PACKER FIELD TEST Field Report for the period of October 21, 1999 November 01, 1999 Date Published: June 30, 2000 Tricia Schneller, Halliburton Energy Services Jose

More information

PRODUCT LINE. CPS Oil & Gas Equipments Private Limited. Liner Hanger System. Gas Lift Equipment. Cementing and Casing Accessories

PRODUCT LINE. CPS Oil & Gas Equipments Private Limited. Liner Hanger System. Gas Lift Equipment. Cementing and Casing Accessories PRODUCT LINE CPS Oil & Gas Equipments Private Limited Liner Hanger System Cementing and Casing Accessories Completion and Downhole Equipment Gas Lift Equipment COMPANY PROFILE CPS, a company based on Indian

More information

Tryton. Tool Services. People. Products. Performance. Canadian Locations

Tryton. Tool Services. People. Products. Performance. Canadian Locations Tool Services Canadian Locations Lloydminster - Corporate Office 6702-56 Street Lloydminster, AB T9V 3A7 Ph: 780 875-0800 (24hr) Brooks - Field Office 329-9th St. E Brooks, AB T1R OK2 Ph: 403 362-8600

More information

44. Bit record form Rig site daily drilling report form Office drilling report Computerized drilling information network

44. Bit record form Rig site daily drilling report form Office drilling report Computerized drilling information network Figures v Tables vii Foreword ix Acknowledgments xi Units of Measurement xii Introduction 1 Well Planning 5 Bits 9 Bit Selection 9 Bit Design 11 How Bits Drill 12 Roller Cone Bits 13 Natural Diamond Bits

More information

3/25/15 University DC 1H Devonian Completion

3/25/15 University DC 1H Devonian Completion 3/25/15 DAILY: $ 292,266.34 ACC: $ 292,266.34 Toe Prep. (12:22-13:24) SPRAYBERRY FORMATION Casing Tested @ 6076 psi and chart for 5 minutes (RRCT), Open Toe Tool @ 6557 psi, Injection Rate @ 1 bpm, Pumped

More information

Special Features. u By-pass below upper slips to wash. debris when valve is opened. u By-pass is opened before upper slips.

Special Features. u By-pass below upper slips to wash. debris when valve is opened. u By-pass is opened before upper slips. Quality We Know Downhole. ASI-X Packer The D&L ASI-X Packer is the most versatile of the mechanically set retrievable packers and may be used in any production application. The ASI-X Packer is suited for

More information

RENTAL TOOL SERVICES. Megaton Impact Tools

RENTAL TOOL SERVICES. Megaton Impact Tools Megaton Impact Tools Upper Connector Megaton Impact Tools optimize your drilling operations. Drive Mandrel Female Spline Bearing Female Spline New-Generation Drilling Tools Megaton Drilling Jar Frees the

More information

POWR Series. Performance and Steerable Drilling Motors

POWR Series. Performance and Steerable Drilling Motors POWR Series Performance and Steerable Drilling Motors Drilling Reliable. Innovative. Premium. We are proud of our products and their contribution to the downhole drilling and thru-tubing industries. Research

More information

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,

More information

GT GAS-TIGHT SERIES ELIMINATOR. Addressing your wellbore isolation and cement needs through an ISO V0-rated stage-cementing package

GT GAS-TIGHT SERIES ELIMINATOR. Addressing your wellbore isolation and cement needs through an ISO V0-rated stage-cementing package WELL CONSTRUCTION ELIMINATOR GT GAS-TIGHT SERIES Addressing your wellbore isolation and cement needs through an ISO 14998 V0-rated stage-cementing package DRILLING & FORMATION EVALUATION WELL CONSTRUCTION

More information

RODEC "C" Low Profile Rotator / RODEC "C" Integral Rotator (3 in 1)

RODEC C Low Profile Rotator / RODEC C Integral Rotator (3 in 1) We have been providing effective tubing wear solutions for over 70 years. Whether using rod pumping units or progressing cavity downhole pumps, we offer the most complete package of wear prevention solutions

More information

Cloppenburg Germany Germany Tel.: +49 (0) Hohe Tannen 14

Cloppenburg Germany Germany Tel.: +49 (0) Hohe Tannen 14 Downhole Tools Fangmann Energy Services GmbH & Co. KG Hohe Brietzer Tannen Weg 14 10 49661 29410 Cloppenburg Salzwedel Tel.: Tel.: +49 +49 (0)4471 (0)3901 98008-0 8363-0 Fax: Fax: +49 +49 (0)4471 (0)3901

More information

Tryton. Tool Services. People. Products. Performance. Calgary - Sales/Marketing Office 1100, 250 2nd St. SW Calgary, AB T2P 0C1 Ph:

Tryton. Tool Services. People. Products. Performance. Calgary - Sales/Marketing Office 1100, 250 2nd St. SW Calgary, AB T2P 0C1 Ph: Tool Services Lloydminster Field Office Corporate/Accounting Office 6702-56 Street Lloydminster, AB T9V 3A7 Ph: 780 875-0800 (24hr) Brooks Field Office 329-9th St. E Brooks, AB T1R OK2 Ph: 403 362-8600

More information

Jet Research Center Segmented Explosive Jet Cutters

Jet Research Center Segmented Explosive Jet Cutters Jet Research Center Segmented Explosive Jet Cutters Field Loading Procedures WARNING Refer to and apply the procedures listed in the Recommended Practices for Oilfield Explosives Safety; API Recommended

More information

SLIDING SLEEVE. BSS-S Profile BSS-H Profile

SLIDING SLEEVE. BSS-S Profile BSS-H Profile SLIDING SLEEVE BSS-S Profile BSS-H Profile BSS SLIDING SLEEVE INNER SLEEVE CLOSED POSITION TOP SUB UPPER SUB BODY SUB LOWER SUB BOTTOM SUB The Benoit Sliding Sleeve TM (BSS) is a premium Chrome Alloy flow

More information

MagnusSeal Retrievable Seal Bore Packer Product No.: MSP 7500

MagnusSeal Retrievable Seal Bore Packer Product No.: MSP 7500 Product No.: MSP 7500 Packer Retrieving Tool www.maximuscompletions.com is a reliable high pressure packer used for production, gravel packing, or injection applications. seal bore packer is set on wireline

More information

Coiled Tubing Tools Table of Contents Primary Tools Slim Line Dimple / Slip Connector...Page 6 Full Size Dimple / Slip Connector...Page 6 Slimconnect External Slip Connector...Page 7 External Slip Connector...Page

More information

Subsurface Flow Controls

Subsurface Flow Controls Subsurface Flow Controls Subsurface Flow Controls Landing Nipples X, R, RPT, FBN Lock Mandrels and accessories Nippleless Tubing Plugs - Mirage plug, Monolock DuraSleeve Sliding Side-Door circulating device

More information

Generation IV Single- Trip Multizone FracPac System. Overview

Generation IV Single- Trip Multizone FracPac System. Overview Generation IV Single- Trip Multizone FracPac System Overview Ricki Jannise Principal Product Champion Multizone Sand Control 281 988 2282 or 713 702 6716 Ricki.jannise@halliburton.com What is it? Single-Trip

More information

TABLE OF CONTENT. Description

TABLE OF CONTENT. Description TABLE OF CONTENT Description Page OQLH Liner Hanger Packer Combo 1 Set Liner Packer Hydraulic or Mechanical Set 2 Quartus QLG Liner Extension Assembly 3 Quartus Liberty Liner Hangers Single & Dual Cone

More information

CONTINUOUS FLIGHT AUGERS AND BITS

CONTINUOUS FLIGHT AUGERS AND BITS Mobile Standard Construction and HEX-COR augers have been tested in the field and independently tested in the laboratory and are proven to be equal to or stronger than any other auger in the industry.

More information

W I L D W E L L C O N T R O L COILED TUBING

W I L D W E L L C O N T R O L COILED TUBING COILED TUBING Coiled Tubing Learning Objectives You will learn about types of coiled tubing rigs. You will learn best practices and techniques for conducting coiled tubing operations. You will learn the

More information

Sentinel 250 Fire Hydrant

Sentinel 250 Fire Hydrant Maintenance Instructions manual table of contents PAGE Sentinel 250 Fire Hydrant Inspection and Lubrication 2 Rotating Hydrant to Face Desired Direction 3 Installing Extension Section 3-6 Restoring Service

More information

SPE MS. Abstract

SPE MS. Abstract SPE-179088-MS Optimizing Bridge Plug Milling Efficiency Utilizing Weight-On-Bit to Control Debris Size: A Comparative Study of the Debris Size vs Weight-On-Bit Utilizing Five Bladed Carbide Mill, Tri-Cone

More information

Vibratory Downhole Tool Technologies with Application to Horizontal Drilling and Casing Installation

Vibratory Downhole Tool Technologies with Application to Horizontal Drilling and Casing Installation Vibratory Downhole Tool Technologies with Application to Horizontal Drilling and Casing Installation 2/5/2013 Roger L. Schultz TTS Drilling Solutions Presentation Overview Frictional Forces, Vibratory

More information

APPROACH OPERATING LLC. RIG: Latshaw rig # 22 KB: 28

APPROACH OPERATING LLC. RIG: Latshaw rig # 22 KB: 28 MORNING DRILLING REPORT Date: 6/5/2013 Day: 1 Present Operation: Drilling 12 1/4" hole with bit # 1 Depth: 609 Footage: 569 Rot. Hrs.: 6 Cum Rot Hrs: 6 Daily ROP: 94.83 Brief Description Of Operations:

More information

RENTAL TOOL SERVICES. Megaton Impact Tools

RENTAL TOOL SERVICES. Megaton Impact Tools Megaton Impact Tools Megaton Impact Tools optimize your drilling operations. Megaton Impact Tools Ulti-Torq high-torque, double shoulder connections Involute spline design High-strength steel developed

More information

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.

Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore

More information

Using Drilling Dynamics To Reduce Drilling costs

Using Drilling Dynamics To Reduce Drilling costs 1 Welcome Using Drilling Dynamics To Reduce Drilling costs 2 Using Drilling Dynamics The cost of the drill bit, mud motor, and other BHA components depends the downhole conditions in which they operate.

More information

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM. QAD#IM6055.REVA

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM.  QAD#IM6055.REVA LSSN Butterfly Valve Installation Operation Maintenance Licence Number: 5326 www.challengervalves.com.au 1 Index 1. INTRODUCTION 1.1 Design Features 3 1.2 Flange and Pipe Compatibility 4 1.3 Operating

More information

TOP TOOLS GmbH Alter Flugplatz Vechta

TOP TOOLS GmbH Alter Flugplatz Vechta Unit No. CTC 001-006 Page 3 of 50 Internal Coiled Tubing Connector Coiled Tubing Connectors provide a means of attaching a tool string to the end of the coiled tubing. The connectors, when installed correctly,

More information

JFEBEAR RUNNING MANUAL

JFEBEAR RUNNING MANUAL JFEBEAR-TP-M-001 (REV.2) JFEBEAR RUNNING MANUAL JANUARY 2007 JFE STEEL CORPORATION Legal Notice The use of the information is at the reader's risk and no warranty is implied or expressed by JFE Steel Corporation

More information

JFETIGER RUNNING MANUAL. Downloaded From JFETC.COM Thu, 20 Sep :15: JFETIGER. * valid at time of download * JANUARY 2015

JFETIGER RUNNING MANUAL. Downloaded From JFETC.COM Thu, 20 Sep :15: JFETIGER. * valid at time of download * JANUARY 2015 JFETIGER-TP-M-001 (REV.3) JFETIGER RUNNING MANUAL JFETIGER JANUARY 2015 JFE STEEL CORPORATION CONTENTS JFETIGER... 1 PREFACE...1 1 PREPARATIONS BEFORE RUNNING...1 1.1 Handle Pipes Carefully...1 1.2 Racking

More information

DRILLING MOTOR HANDBOOK

DRILLING MOTOR HANDBOOK DRILLING MOTOR HANDBOOK April 218 About Tartan About Tartan Tartan Energy Group (Tartan) is a multifaceted energy services company that engineers and manufactures innovative, customized multistage stimulation

More information

Valveworks USA Operation and Maintenance Booklet Model FC

Valveworks USA Operation and Maintenance Booklet Model FC Operation and Maintenance Booklet Model FC MODEL FC 3000, 5000, 10000, & 15000 W.P. FLOATING SLAB GATE VALVES 1 13/16-2 1/16-2 9/16-3 1/16-4 1/16 BOOKLET APPROVED BY: INTRODUCTION In appreciation to you

More information

View Details... Event. In Progress. Dev Completion - Cased. Hole 09/30/2013

View Details... Event. In Progress. Dev Completion - Cased. Hole 09/30/2013 Event In Progress CAMERON-7 Hole 09/30/2013 Dev Completion - Cased Daily Summary CAMERON 7 WOC-Chuck Pannell Daily Cost=$9700 Cum Cost=$9700 9-30-13 -MIRU Halliburton wireline. RIH and log CNL, CCL, GR,

More information

DRUM BRAKE RIMS Periodic inspection of drum brake rims is necessary to determine indications of uneven or excessive wear. In general, brake rim failures other that regular wear are caused by brake linings

More information

Completion Data. License # Rig Release Date 5/31/ :00 5/9/ :30. End Date 6/9/ :00

Completion Data. License # Rig Release Date 5/31/ :00 5/9/ :30. End Date 6/9/ :00 Job Category COMPLETION AFE Number E14178 Job Contacts Roger Web Primary Job Type Initial Completion Start Date Secondary Job Type Status 1 End Date 6/9/2015 06:00 870-314-2454 Buddy Haney 580-799-0217

More information

MANUFACTURING. PD Impact Tools

MANUFACTURING. PD Impact Tools PD Impact Tools Upper Connector MANUFACTURING Drive Mandrel Female Spline Bearing Female Spline PD Impact Tools optimize your drilling operations. Knocker Housing Knocker Pressure Piston Hydraulic Mandrel

More information

Overshots. Drill Rods. Casing. Tools 08/05-MKT1565 P/N L

Overshots. Drill Rods. Casing. Tools 08/05-MKT1565 P/N L REV 0-NOV-05 Diamond Products Core Barrels Overshots Drill Rods Water Swivels Hoisting Plugs Casing Recovery Tools Adapter Subs Conversion Kits Tools Technical Data Safety Poster Diamond Products Impregnated

More information

Insta-Valve 250 Patriot TM

Insta-Valve 250 Patriot TM Insta-Valve 250 Patriot TM 4-12 Nominal Size Installation Instructions for use with the Hydra-Core Pipewall Sampling Kit IV250MAN 4-12 IV 250 PWSK v1.93 Revised 07/11/2018 Covered by United States Patent

More information

COMPREHENSIVE OVERVIEW

COMPREHENSIVE OVERVIEW COMPREHENSIVE OVERVIEW stingercanada.com 3 About Stinger 5 Ball Launchers 10 Frac Stacks 17 Buffalo Heads 18 Isolation Tools Grande Prairie 11303 96 Avenue Grande Prairie, AB T8V 5M3 780-513-3696 Calgary

More information

FRAC STACKS stingercanada.com

FRAC STACKS stingercanada.com FRAC STACKS stingercanada.com Grande Prairie 11303 96 Avenue Grande Prairie, AB T8V 5M3 780-513-3696 Calgary 420-510 5th Street SW Calgary, AB T2P 3S2 403-340-0716 Red Deer 334-28042 Hwy 11 Red Deer County,

More information

Internal Pressure Pipe Cutters. Manual E540

Internal Pressure Pipe Cutters. Manual E540 Internal Pressure Pipe Cutters Manual E540 Contents Logan Internal Pressure Pipe Cutters Overview...2 Uses...2 Construction...2 Tool Illustration...3 Operation...2 Single Cut from a Fixed Platform... 2

More information

ExL Petroleum, LP DAILY WELL COMPLETION REPORT DATE: DAY #

ExL Petroleum, LP DAILY WELL COMPLETION REPORT DATE: DAY # 6/7/2010 1 API #: 42-003-41652 Cased Hole Log PB SUPERVISOR: RAY DAVIS MIRU Wood Group WL on a crane truck. RIH w/gr/cnl/rcbl tool string. Found TD @ 11,113' WL depth. Logged a 300' repeat section. Main

More information

6200 Series. Specifications. Fluid End Power End Models 6211, 6212, 6221, & 6222 Models 6241 & 6242 Part Material Part Material Part Material

6200 Series. Specifications. Fluid End Power End Models 6211, 6212, 6221, & 6222 Models 6241 & 6242 Part Material Part Material Part Material 5.2018.12.i 6200 Series Specifications The Flomore 6200 Series Pump line consists of a series of basic pump options all developed from a modular power unit. All units are pneumatically driven positive

More information

DAILY DRILLING REPORT

DAILY DRILLING REPORT UNIVERSITY LANDS 11-7 NO. 1 PAGE 1 12-14-11: BEGIN MIRU TRINIDAD 204. 12-15-11: CONTINUE MIRU TRINIDAD 204. DRILLED WATER WELL W/LATZEL WATER WELL TO 620. RU ROTARY TOOLS. APPROX. 40% THIS AM. ESTIMATED

More information

TCI DUAL QUARTER ANCHOR CATCHER (TDQAC)

TCI DUAL QUARTER ANCHOR CATCHER (TDQAC) TCI DUAL QUARTER ANCHOR CATCHER (TDQAC) The TQDA is a rugged anchor-catcher that operates with minimum (less than a 1/4 turn) tubing string rotation to set or release. The no torque option resists right

More information

APPROACH OPERATING LLC. RIG: Latshaw rig #22 KB: 28

APPROACH OPERATING LLC. RIG: Latshaw rig #22 KB: 28 MORNING DRILLING REPORT Date: 8/18/2013 Day: 1 Present Operation: waiting on daylight to finish rig move Depth: Footage: Rot. Hrs.: Cum Rot Hrs: 0 Daily ROP: ##### Brief Description Of Operations: move

More information

Floating & Guiding Equipment

Floating & Guiding Equipment Last Revision: FEBRUARY 3, 2015 Floating & Guiding Equipment Floating equipment is commonly used on the lower sections of the casing to reduce derrick stress by allowing the casing to be floated into place.

More information

Smith Meter PD Meters Meter, PD Series, M16-S3, S5, S6 (1993-Present) Parts List

Smith Meter PD Meters Meter, PD Series, M16-S3, S5, S6 (1993-Present) Parts List Issue/Rev. 0.0 (1/14) Smith Meter PD Meters Meter, PD Series, M16-S3, S5, S6 (1993-Present) Parts List Bulletin PO01023 *For meters which began shipping in 1993 to current. For meters shipped prior to

More information

DATE: 01/03/ DAILY COMPLETION REPORT

DATE: 01/03/ DAILY COMPLETION REPORT DATE: 01/03/2012 045797 OPERATOR. LONE STAR, LLC 01/01/2012 01/02/2012 12/30/11 thru 01/01/12 No activity. DAILY COST.... 0 COMPLETION DAYS. 97 CUMULATIVE COST. 3,400,985 DROVE TO LOCATION / HELD A SAFETY

More information

Partner - Drilling. Well Name: Fcu State/Province Texas Ground/Corrected Ground Elevation (ft) Rig

Partner - Drilling. Well Name: Fcu State/Province Texas Ground/Corrected Ground Elevation (ft) Rig : 4/8/2016 Release Wait on daylight to complete rig move. 95,193.70 95,193.70 24hr MIRU from FCU 7220 to FCU 7442. Change out gen #2 motor. Clean and service rig. Wait on daylight to complete rig move.

More information

RODEC TUBING ROTATOR SOLUTIONS

RODEC TUBING ROTATOR SOLUTIONS RODEC TUBING ROTATOR SOLUTIONS RODEC TUBING ROTATOR SOLUTIONS One Company, Unlimited Solutions Since 1841, National Oilwell Varco has been dedicated to ensuring customers receive the highest quality oilfield

More information

VALVEWORKS USA OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC PSI W.P FLOATING SLAB GATE VALVES

VALVEWORKS USA OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC PSI W.P FLOATING SLAB GATE VALVES OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC 3000-15000 PSI W.P FLOATING SLAB GATE VALVES INTRODUCTION In appreciation to our customer for purchasing our product, we have prepared this

More information

CT Plus. Coiled tubing bits for plug milling

CT Plus. Coiled tubing bits for plug milling CT Plus Coiled tubing bits for plug milling Designed specifically to optimize performance in plug milling including coiled tubing and workover operations, small-diameter CT Plus* coiled tubing bit from

More information

RECOMMENDED PRACTICE TKC FJ-150

RECOMMENDED PRACTICE TKC FJ-150 1.0 SCOPE 1.1 This document sets forth Hunting s recommended practice for the field running and handling procedures that should be used in conjunction with all Hunting tubing and casing product line connections.

More information

AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER

AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL, AIR ANGLE GRINDER and AIR DIE GRINDER AIR DRILL KW0800256 3/8 Chuck, Reverse Equipped with precision chucks for excellent accuracy Precision bearing provides longer tool durability KW0800258

More information

Internal Cutters. Manual E535

Internal Cutters. Manual E535 Internal Cutters Manual E535 CONTENTs Logan Internal Cutters Overview...2 Uses...2 Construction...2 Operation...2 Operating Precautions... 2 Cutting Procedure...2 Determining Free Length of Pipe... 6 Maintenance...2

More information

ADDRESSABLE DISCONNECT TOOL MODEL DE MANUAL

ADDRESSABLE DISCONNECT TOOL MODEL DE MANUAL Pg. 1 of 77 ADDRESSABLE DISCONNECT TOOL MODEL DE MANUAL REVISION HISTORY AUTHOR REVISED SECTION/PARAGRAPH REV RELEASED Gary Floyd Final Draft 0 03/31/17 Draft and Archived/Obsolete revisions are not to

More information

CHOKES API 6A & 16C Extreme Service/Drilling Chokes

CHOKES API 6A & 16C Extreme Service/Drilling Chokes CHOKES API 6A & 16C Extreme Service/Drilling Chokes Robust Reliable Proven The Standard in Non-Standard Valve Production www.uscortec.com CORTEC Models CX3 and CXE-II Drilling/Extreme Service Chokes CORTEC

More information

RECOMMENDED PROCEDURE FOR INSTALLATION OF DRILLCO MAXI-BOLT ANCHORS

RECOMMENDED PROCEDURE FOR INSTALLATION OF DRILLCO MAXI-BOLT ANCHORS RECOMMENDED PROCEDURE FOR INSTALLATION OF DRILLCO MAXI-BOLT ANCHORS Revision 0588VO By Drillco National Group P. O. Box 2182 Long Island City, NY 11102 Telephone: (800) 391-0052 www.drillcogroup.com techsupport@drillcogroup.com

More information