OT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
|
|
|
- Cora Hill
- 5 years ago
- Views:
Transcription
1 POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
2 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE SWITCH BASE (See page IP-21) 3. REMOVE POWER OUTLET SOCKET (a) Rotate the socket to disengage the notch. E (b) (c) Pull out the socket halfway and rotate the socket until its protrusion is aligned with the groove of the cover. Remove the socket from the cover. B B INSTALLATION 1. INSTALL POWER OUTLET SOCKET (a) Align the protrusion on the backside of the socket with the groove of the cover. Then push the socket into the cover. 2. INSTALL SWITCH BASE (See page IP-24) 3. CONNECT CABLE TO NEGATIVE BATTERY
3 HER SYSTEM CENTER POWER OUTLET SOCKET CENTER POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS 3 NO. 2 CONSOLE UPPER PANEL GARNISH SHIFT LEVER KNOB SUB- UPPER CONSOLE PANEL SUB- NO. 1 CONSOLE UPPER PANEL GARNISH POWER OUTLET SOCKET COVER CENTER POWER OUTLET SOCKET UPPER REAR CONSOLE PANEL SUB- B130930E03
4 4 HER SYSTEM CENTER POWER OUTLET SOCKET REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH (See page IP-17) 3. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH (See page IP-18) 4. REMOVE SHIFT LEVER KNOB SUB- 5. REMOVE UPPER CONSOLE PANEL SUB- (See page IP-18) 6. REMOVE UPPER REAR CONSOLE PANEL SUB- (See page IP-19) 7. REMOVE CENTER POWER OUTLET SOCKET (a) Rotate the socket to disengage the notch. E (b) (c) Pull out the socket halfway and rotate the socket until its protrusion is aligned with the groove of the cover. Remove the socket from the cover. B108949
5 HER SYSTEM CENTER POWER OUTLET SOCKET 5 B INSTALLATION 1. INSTALL CENTER POWER OUTLET SOCKET (a) Align the protrusion on the backside of the socket with the groove of the cover. Then push the socket into the cover. 2. INSTALL UPPER REAR CONSOLE PANEL SUB- (See page IP-27) 3. INSTALL UPPER CONSOLE PANEL SUB- (See page IP-27) 4. INSTALL SHIFT LEVER KNOB SUB- 5. INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH (See page IP-28) 6. INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH (See page IP-28) 7. CONNECT CABLE TO NEGATIVE BATTERY
6 6 HER SYSTEM CENTER POWER OUTLET SOCKET (for AC Power Supply) CENTER POWER OUTLET SOCKET (for AC Power Supply) BODY HER ELECTRICAL SYSTEM COMPONENTS CENTER POWER OUTLET SOCKET CONSOLE REAR END PANEL B130927E01
7 HER SYSTEM CENTER POWER OUTLET SOCKET (for AC Power Supply) 7 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE CONSOLE REAR END PANEL (See page IP- 19) 3. REMOVE CENTER POWER OUTLET SOCKET (a) Disconnect the connector. (b) Detach the 2 claws and remove the power outlet. B B INSTALLATION 1. INSTALL CENTER POWER OUTLET SOCKET (a) Attach the 2 claws to install the voltage inverter. (b) Connect the connector. 2. INSTALL CONSOLE REAR END PANEL (See page IP- 27) 3. CONNECT CABLE TO NEGATIVE BATTERY
8 8 HER SYSTEM REAR POWER OUTLET SOCKET REAR POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS REAR DOOR OPENING TRIM WEATHERSTRIP LH RECLINING REME CONTROL LEVER BEZEL LH SIDE WINDOW GARNISH HOOK DECK TRIM SIDE SERVICE HOLE COVER REAR SEAT SHOULDER BELT HANGER TETHER ANCHOR BRACKET SUB- 12 (125, 10) REAR NO. 1 SEAT BELT OUTER LH DECK TRIM SIDE PANEL LH REAR POWER OUTLET SOCKET REAR DOOR SCUFF PLATE LH N*m (kgf*cm, ft.*lbf) : Specified torque ROPE HOOK B135697E03
9 HER SYSTEM REAR POWER OUTLET SOCKET 9 PACKAGE TRAY TRIM POCKET SUB- TONNEAU COVER BACK DOOR WEATHERSTRIP REAR FLOOR FINISH PLATE DECK BOARD REAR FLOOR NO. 2 BOARD REAR FLOOR NO. 1 BOARD REAR FLOOR NO. 3 BOARD REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE B130111E21
10 10 HER SYSTEM REAR POWER OUTLET SOCKET REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. 2. REMOVE REAR DOOR SCUFF PLATE LH (See page IR-26) 3. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 4. REMOVE PACKAGE TRAY TRIM POCKET SUB- 5. REMOVE TONNEAU COVER 6. REMOVE REAR FLOOR NO. 1 BOARD 7. REMOVE DECK BOARD 8. REMOVE REAR FLOOR NO. 3 BOARD 9. REMOVE REAR FLOOR NO. 2 BOARD 10. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (See page IR-31) 11. REMOVE BACK DOOR WEATHERSTRIP 12. REMOVE REAR FLOOR FINISH PLATE (See page IR- 31) 13. REMOVE RECLINING REME CONTROL LEVER BEZEL LH 14. REMOVE TETHER ANCHOR BRACKET SUB- 15. REMOVE DECK TRIM SIDE PANEL LH (w/ Rear No. 2 Seat) (See page IR-32) 16. REMOVE DECK TRIM SIDE PANEL LH (w/o Rear No. 2 Seat) (See page IR-32) 17. REMOVE REAR POWER OUTLET SOCKET (a) Detach the 2 claws fittings and remove the socket. B133576
11 HER SYSTEM REAR POWER OUTLET SOCKET 11 B INSTALLATION 1. INSTALL REAR POWER OUTLET SOCKET (a) Attach the 2 claw fittings to install the socket. 2. INSTALL DECK TRIM SIDE PANEL LH (w/ o Rear No. 2 Seat) (See page IR-52) 3. INSTALL DECK TRIM SIDE PANEL LH (w/ Rear No. 2 Seat) (See page IR-53) 4. INSTALL TETHER ANCHOR BRACKET SUB- 5. INSTALL RECLINING REME CONTROL LEVER BEZEL LH 6. INSTALL REAR FLOOR FINISH PLATE (See page IR- 55) 7. INSTALL BACK DOOR WEATHERSTRIP 8. INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (See page IR-55) 9. INSTALL REAR FLOOR NO. 2 BOARD 10. INSTALL REAR FLOOR NO. 3 BOARD 11. INSTALL DECK BOARD 12. INSTALL REAR FLOOR NO. 1 BOARD 13. INSTALL TONNEAU COVER 14. INSTALL PACKAGE TRAY TRIM POCKET SUB- 15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 16. INSTALL REAR DOOR SCUFF PLATE LH (See page IR-59) 17. CONNECT CABLE TO NEGATIVE BATTERY
LI 84 LIGHTING REAR COMBINATION LIGHT ASSEMBLY REMOVAL
84 GHTING REAR COMBINATION GHT ASSEMBLY REMOVAL HINT: Use the same procedure for both the RH and LH sides, unless otherwise specified. The procedure described below is for the LH side. 1. DISCONNECT CABLE
REASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
IR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
SEAT BELT WARNING SYSTEM
SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the
ON-VEHICLE INSPECTION
51 Connector Front Side: A5 ON-VEHICLE INSPECTION 1. INSPECT TOWING CONVERTER RELAY (a) Measure the voltage and check the result in accordance with the value(s) in the table below. Standard E064833E01
REMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
Model Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
REPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
DISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
Headlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
POWER MIRROR CONTROL SYSTEM
RROR POWER RROR CONTROL SYSTEM POWER RROR CONTROL SYSTEM BODY RROR PARTS LOCATION 1 DRIVER SIDE JUNCTION BLOCK - ACC FUSE - AM2 FUSE - ACC-B FUSE OUTER REAR VIEW RROR RH OUTER REAR VIEW RROR LH ACC RELAY
Telescopic Lever Detent Clip Replacement
T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained
ROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
SEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
STEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
REASSEMBLY SE INSTALL REAR SEATBACK LOCK ASSEMBLY (a) Install the rear seatback lock with the 2 bolts. Torque: 18 N*m (185 kgf*cm, 13 ft.
AT REAR AT ASMBLY (for RH Side) 49 REASMBLY CAUTION: Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands. 1. INSTALL REAR
ED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
ED 13. ENGINE HOOD / DOOR FRONT DOOR (w/ Power Window) DISASSEMBLY
13 B088092E01 DISASSEMBLY Use the same procedures for both the LH and RH sides. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Disengage the
FLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
SRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA
INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA PARA AIRBAG DE CORTINA I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check the VIN range. 2. Check the TIS Vehicle Inquiry System. Not Covered No further
Page 1 of 33 SPECIFICATIONS 2013 Ford Edge 3.5L Eng Limited Print Date: TORQUE SPECIFICATIONS Description Nm lb-ft lb-in Assist handle bolts 9-80 B-pillar upper trim panel screw 9-80 C-pillar trim panel
OVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
Convertible Top Component Rattle
L-SB-0149-10 November 16, 2010 Service Category Vehicle Exterior Section Sliding Roof/Convertible Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2010 IS250C, IS350C Introduction Some
COMPONENTS Toyota RAV ACCESSORIES & EQUIPMENT Front Seat - RAV4
2005 ACCESSORIES & EQUIPMENT Front Seat - RAV4 COMPONENTS Fig. 1: Identifying Front Seat Components & Torque Specifications FRONT SEAT ASSEMBLY REMOVAL CAUTION: Wear safety gloves, because the cutting
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Last Modified: 4-26-2007 Service Category: Drivetrain 1.6 A Section: Automatic Transmission/Transaxle Model Year: 2007 Model:
1. General Description
EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,
Code Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
Rubbing Noise from Steering Shaft/Column Area
L-SB-0084-13 October 25, 2013 Service Category Steering Section Steering Gear/Linkage Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2011 2013 LS460 Drive Type(s): 4WD VDS(s): CL1EF,
RAV4 Hybrid. Gasoline-Electric Hybrid Synergy Drive
RAV4 Hybrid Gasoline-Electric Hybrid Synergy Drive AVA42/AVA44 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Toyota RAV4 Hybrid gasoline-electric hybrid
FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
ALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Page 1 of 9 Service and Repair FRONT WIPER MOTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM HEAD CAP a. Using a screwdriver wrapped with protective tape, remove
DISASSEMBLY REASSEMBLY
4 EXTERIOR FRONT BUMPER DISASSEMBLY 1. REMOVE HOOD TO FRONT END PANEL SEAL (a) Using a clip remover, detach the 8 clips and remove the panel seal. 2. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a clip
Plastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire Cutter. (FOR VEHICLES w/o A SHIFT BOOT)
INSTALLATION INSTRUCTIONS C10FL0 DESCRIPTION: STI CVT SHIFT KNOB STI CVT SHIFT KNOB TOOLS REQUIRED: PARTS IDENTIFICATION: Plastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire
EC 44 1NZ-FXE EMISSION CONTROL AIR FUEL RATIO SENSOR AIR FUEL RATIO SENSOR CONNECTOR WIRE HARNESS CLAMP. AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)
44 1NZ-FXE EMISSION CONTROL AIR FUEL RATIO SENSOR AIR FUEL RATIO SENSOR CONNTOR WIRE HARNESS CLAMP N*m (kgf*cm, ft.*lbf) : Specified torque 44 (449, 32)*1 40 (408, 30)*2 AIR FUEL RATIO SENSOR (for Bank
TOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
SECTION 9G INTERIOR TRIM
SECTION 9G INTERIOR TRIM CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
INSTRUMENT PANEL ASSEMBLY
2003 Dodge or Ram Truck RAM 1500 Truck 2WD V8-4.7L VIN N Vehicle > Body and Frame > Interior Moulding / Trim > Dashboard / Instrument Panel > Service and Repair > Removal and Replacement INSTRUMENT PANEL
FRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page 718 1. TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the
WIPER AND WASHER SYSTEM
WIPER AND WASHER WIPER AND WASHER SYSTEM WIPER AND WASHER SYSTEM PRECAUTION 1 NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable
BR 43. BRAKE HYDRAULIC BRAKE BOOSTER (w/ VSC) REMOVAL
AKE HYDRAULIC AKE BOOSTER (w/ VSC) 43 REMOVAL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 20 times. As high pressure is applied to the brake
LC500h. Gasoline-Electric Lexus Hybrid Drive. GWZ100 Series
LC500h Gasoline-Electric Lexus Hybrid Drive GWZ100 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Lexus LC500h gasoline-electric hybrid vehicles. LC500h
Side Window Glass Noise During Operation
T-SB-0077-12 May 21, 2012 Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2012 Camry, Camry HV Introduction Some 2012 Camry and Camry
TOYOTA RAV TRAILER WIRE HARNESS Section I Installation Preparation
Section I Installation Preparation Part Number: 08921-42900 Kit Contents Item # Quantity Reqd. Description 1 1 Converter 2 1 Wire harness 3 1 Sub wire harness No.1 4 2 Plastic Tie (300mm) 5 21 Plastic
SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The
13.Curtain Airbag Sensor
urtain Airbag Sensor AIRAG SYSTEM 13.urtain Airbag Sensor A: REMOVAL 1. 4 DOOR MODEL 1) Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. AUTION: Airbag system
REAR BUMPER COMPONENTS. Luggage Compartment. Trim Cover Assy RH. Rope Hook Assy. Deck Trim Side Board LH. Deck Trim Side Board RH.
767 COMPONENTS 7615701 Deck Trim Side Board LH Deck Trim Side Board RH Luggage Compartment Trim Cover Assy RH Luggage Compartment Floor Mat Luggage Compartment Trim Cover Assy LH Rear Floor Finish Plate
Rear Door: Service and Repair REAR DOOR
2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY
SCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
04 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER Installation Instruction PART No. H6710AL010 EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 1 2 3 TOOLS NEEDED PRECAUTIONS
ARTICLE BEGINNING COMPONENTS FRONT DOOR Toyota Tacoma
Page 1 of 17 ARTICLE BEGINNING COMPONENTS Page 2 of 17 Fig. 1: Front Door Components (w/o Power Door Lock & Power Window Regulator) Page 3 of 17 Fig. 2: Front Door Components (W/ Power Door Lock & Power
OVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
AUDIO AND VISUAL SYSTEM
AUDIO / VISUAL AUDIO AND VISUAL SYSTEM 1 AUDIO AND VISUAL SYSTEM BODY ELECTRICAL / VISUAL PARTS LOCATION HATCHBACK (5-Door Models): AMPLIFIER ANTENNA ASSEMBLY ANTENNA CORD SUB-ASSEMBLY RADIO ANTENNA POLE
Whine Noise From Rear of Vehicle
T-SB-003-8 February 6, 208 Service Category Drivetrain Section Axle/Differential Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMION 206-207 Tacoma Body Type(s): D CAB Introduction Some 206
(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector.
REMOVAL 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. 3. DISCHARGE FUEL SYSTEM PRESSURE
2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6
2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6 Vehicle» Body and Frame» Interior Moulding / Trim» Dashboard / Instrument Panel» Service and Repair» Instrument Panel Assembly REMOVAL
SCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
DVD REAR SEAT VIDEO SYSTEM
Read entire instructions thoroughly before starting. TOOLS REQUIRED: DVD REAR SEAT VIDEO SYSTEM MINIVANS WITH ROOF RAILS INSTALLATION INSTRUCTIONS Non-metal trim stick Phillips screwdriver T15, T20, T25
Cargo Socket Kit. Securely connect connectors and terminals. Failure to do so can result in poor connections.
00 Cargo Socket Kit Fitting Model OUTBACK October 2014 and later Installation Instructions PART No. H6710AL100 J: To those installing this product Important 1. We recommend that you ask the SUBARU dealer
Conflicts TOYOTA HIGHLANDER DUAL USB POWER DOCK. Part Number: Accessory Code:CP1000. Service Part Numbers.
Part Number: 00016-00222 Accessory Code:CP1000 Conflicts Note: Service Part Numbers Kit Contents Item # Quantity Req d Description 1 1 Dual USB Power Dock 2 General Applicability Hardware Bag Contents
Front Door Non-Functional - Latch Replacement
Page 1 of 6 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Ford Truck Escape 2WD L4-122 2.0L DOHC VIN
Removal & Installation
Page 1 of 11 2011 Nissan Rogue : Body > Interior > Instrument Panel > Removal & Installation Removal & Installation 1. Before servicing the vehicle, refer to the Precautions Section. CAUTION Always work
2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems
DESCRIPTION & OPERATION 2004 ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems WARNING: Accidental air bag deployment is possible. Personal injury may result. Read and follow all WARNINGS
DISPOSAL. CAUTION: Never dispose of front seat outer belt which has an inactivated. activated pretensioner.
DISPOSAL When scrapping vehicles epuipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner) always first active the seat belt pretensioner in accordance
PRIUS PRIME PRIUS PHV
PRIUS PRIME PRIUS PHV Plug-in Hybrid Gasoline-Electric Hybrid Synergy Drive ZVW52 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Toyota PRIUS PRIME,
GENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1
AXLE AXLE SYSTEM 1 AXLE SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of probability of each of the possible causes.
FRONT DOOR COMPONENTS
BO4 FRONT DOOR COMPONENTS BO5 ADJUSTMENT OF FRONT DOOR 1. ADJUST DOOR IN FORWARD /REARWARD AND VERTICAL DIRECTIONS Using SST, adjust the door by loosening the body side hinge bolts. SST 0981200010 2. ADJUST
TECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS DOOR SIDE AIRBAG SENSOR REPLACEMENT RX450h / RX350 / RX200t RX450h/RX350/RX200t Fr ドアエアバッグセンサ交換 一般 _v2.0 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION...
REASSEMBLY MT INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket.
30 RA61F MANUAL TRANSMISSION MANUAL TRANSMISSION UNIT REASSEMBLY 1. INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket. D033725 (b) Install a new
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
Toyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52070 to complete the installation
1 of 13 2/10/ :41 AM
1 of 13 2/10/2017 10:41 AM Trim Removal/Installation - Pillar Areas Special Tools Required KTC trim tool set SOJATP2014 * *Available through the American Honda Tool and Equipment Program A-pillar Trim
LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
TOYOTA COROLLA/MATRIX LOWERING SPRINGS Preparation
Preparation Part Number: PTR40-02080 Kit Contents: Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Vehicle Service Parts (may be required for reassembly) Item
Installation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog #
Installation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog # 3916034 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface
INSTRUMENT PANEL ASSEMBLY. INSTRUMENT PANEL ASSEMBLY Component Parts Drawing IP-10 PFP:68200 AIS005BC PIIB0009E
INSTRUMENT PANEL ASSEMBLY Component Parts Drawing PFP:68200 AIS005BC PIIB0009E IP-10 1. Passenger air bag module 2. Front defroster grille (LH) 3. Front defroster grille (RH) 4. Cluster Lid A 5. Instrument
INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE
Page 1 of 18 2016 Dodge Grand Caravan 3.6L Eng VIN G SE Service Manual: BODY - INTERIOR & EXTERIOR Print Date: INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE Fig 1: Base Floor Console
Conflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware
MY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo
2013-2014MY F150 CrewCab 1 Tools Required A B C D E F G 4X H I J K 3X L 3X 2X 10X 2X Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 2 Vehicles with selector lever in floor
Prius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
THREE WAY CATALYTIC CONVERTER (TWC) SYSTEM
EC26 THREEWAY CATALYTIC CONVERTER (TWC) SYSTEM To reduce C0, HC and NOx emissions, they are oxidized, reduced and converted to carbon dioxide (C02), water 1H20Y and nitrogen (NO by the threeway catalytic
SUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 SUENSION SYSTEM Suspension system Vehicle is unstable Bottoming Sways/pitches Wheels shimmy Abnormal tire wear Vehice pull PROBLEM SYMPTOMS TABLE Use the table below to help
Installation Instructions PISTOL GRIP HANDLE Fits: Dodge Challenger and Charger w/ Automatic Transmission Catalog #
Installation Instructions PISTOL GRIP HANDLE Fits: 2015-2018 Dodge Challenger and Charger w/ Automatic Transmission Catalog # 5380437 WORK SAFELY! For maximum safety, perform this installation on a clean,
Water Leak At Back Door Hatch
T-SB-0008-12 January 6, 2012 Service Category Vehicle Exterior Section Door/Hatch Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2006 2007 Highlander HV 2001 2007 Highlander Introduction
OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
TOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
Toyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52120 to complete the installation
1 of 12 8/18/ :52 AM
1 of 12 8/18/2016 11:52 AM REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE a. Discharge fuel system pressure. 2. REMOVE DECK BOARD SUB-ASSEMBLY a. Disengage the 5 clips and turn up the front side of the deck
GENUINE PARKING SENSORS (Rear)
GENUINE PARKING SENSORS (Rear) INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read
GENUINE Interior Lighting Kit
GENUINE Interior Lighting Kit INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
02 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA PART No. EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 Installation Instruction H6710AL010 1 2 3 TOOLS NEEDED PRECAUTIONS Please refer to
CRUISE CONTROL SYSTEM
Negative (-) Battery Terminal CRUISE CONTROL CRUISE CONTROL SYSTEM Cable System name METER / GAUGE SYSTEM D033496E01 CRUISE CONTROL SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY
2017 Outlander Sport FEATURES AND OPTIONS
2017 Outlander Sport FEATURES AND OPTIONS Mechanical Features Engine 2.0L MIVEC DOHC 16-valve 4-cylinder engine STD STD - - - - - 2.4L MIVEC DOHC 16-valve 4 cylinder engine - - STD STD STD STD STD Transmission/Drive
TOYOTA Matrix XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part