Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
|
|
- Shanon Walton
- 5 years ago
- Views:
Transcription
1 2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with workmore Info. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system. NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnectedmore Info. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration. 1/39
2 REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH Disengage the 3 clips and remove the front door lower frame bracket garnish. 2/39
3 REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration. 3/39
4 Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration. 4/39
5 Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel. REMOVE FRONT ARMREST ASSEMBLY Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly. 5/39
6 REMOVE COURTESY LIGHT ASSEMBLYMore Info REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY Put protective tape around the front door panel. 6/39
7 Text in Illustration *1 Protective Tape Remove the 3 screws. 7/39
8 Using a clip remover, disengage the 10 clips. Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration. 8/39
9 Text in Illustration *1 Reference Boss 9/39
10 *2 Front Door Inner Glass Weatherstrip Disengage the reference boss from the front door panel. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly. 10/39
11 REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration. 11/39
12 Text in Illustration *1 Screwdriver REMOVE DOOR SIDE AIRBAG SENSORMore Info REMOVE FRONT NO. 1 SPEAKER ASSEMBLYMore Info REMOVE OUTER REAR VIEW MIRROR ASSEMBLYMore Info REMOVE FRONT DOOR SERVICE HOLE COVER Remove the bolt. 12/39
13 Disconnect each connector. Disengage the 5 clamps. Remove the front door service hole cover. Hint: Remove any remaining butyl tape from the door. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY Remove the grommet. 13/39
14 Connect the cable to the negative (-) battery terminal. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen. Disconnect the cable from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system. NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnectedmore Info. Disconnect the power window regulator master switch assembly. Remove the 2 bolts. 14/39
15 NOTICE: After the bolts are removed, do not allow the door glass to fall. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration. 15/39
16 NOTICE: Do not damage the door glass. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY Loosen the temporary bolt. Text in Illustration *1 Temporary Bolt NOTICE: Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage. Remove the 5 bolts. Remove the front door window regulator assembly. Remove the temporary bolt from the front door window regulator assembly. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly. 16/39
17 REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION Remove the 2 bolts. 17/39
18 Text in Illustration *1 Double-sided Tape Disengage the 2 guides and remove the No. 2 front door stiffener cushion. REMOVE FRONT DOOR GLASS RUN Remove the front door glass run. 18/39
19 REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY Remove the 2 bolts. Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration. 19/39
20 REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY Remove the 2 bolts. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) Remove the hole plug. 20/39
21 Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly. Hint: The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly. 21/39
22 REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side) w/ Front Door Lock Cylinder: Hint: Use the same procedure for front passenger side and driver side. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) w/ Front Door Lock Cylinder: Hint: Use the same procedure for the front passenger side and the driver side. w/o Front Door Lock Cylinder: Remove the hole plug. 22/39
23 Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover. Hint: The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly. 23/39
24 REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY w/ Smart Key System: Disengage the 2 claws. Using a screwdriver, disconnect the connector. Remove the front door outside handle assembly as shown in the illustration. 24/39
25 REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD Disengage the 3 claws and remove the front door front outside handle pad. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD 25/39
26 Disengage the 2 claws and remove the front door rear outside handle pad. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY Using a T30 "TORX" socket wrench, remove the 3 screws. 26/39
27 Text in Illustration *1 Front Door Lock Open Rod Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit. When reusing the front door lock with motor assembly: Remove the door lock wiring harness seal from the front door lock with motor assembly. 27/39
28 REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY Remove the front door lock remote control cable assembly. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY 28/39
29 Using a screwdriver, disengage the 3 claws. Remove the front door inside locking cable assembly. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY 29/39
30 w/ Smart Key System: Disconnect the connector. Disengage the 3 clamps. Using a T30 "TORX" socket wrench, remove the screw and door handle nut. 30/39
31 Text in Illustration *1 Door Handle Nut 31/39
32 *a Outside *b Inside Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it. REMOVE FRONT DOOR WIRE (w/ Smart Key System) Disengage the 3 clamps and remove the front door wire. REMOVE FRONT DOOR LOCK OPEN ROD Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration. 32/39
33 REMOVE FRONT DOOR CHECK ASSEMBLY Remove the 3 bolts and front door check assembly. 33/39
34 REMOVE FRONT DOOR WEATHERSTRIP Using a clip remover, disengage the 19 clips and remove the front door weatherstrip. 34/39
35 REMOVE DOOR FRAME GARNISH Disengage the clip and remove the door frame garnish. 35/39
36 Hint: This garnish needs to be replaced with a new one because the clip will break when removing it. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip. 36/39
37 REMOVE FRONT DOOR PANEL CUSHION Disengage the 2 claws and remove the 2 front door panel cushions. 37/39
38 REMOVE DOOR DUST PROOF SEAL Remove the door dust proof seal. 38/39
39 REMOVE FRONT DOOR BELT MOULDING ASSEMBLYMore Info REMOVE FRONT DOOR REAR WINDOW FRAME MOULDINGMore Info REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDINGMore Info REMOVE FRONT DOOR STRIPEMore Info REMOVE FRONT DOOR LOWER OUTSIDE STRIPEMore Info Portions of materials contained herein have been reprinted under license from Toyota Motor Sales, U.S.A., Inc., License Agreement TMS /39
DISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
More informationED 13. ENGINE HOOD / DOOR FRONT DOOR (w/ Power Window) DISASSEMBLY
13 B088092E01 DISASSEMBLY Use the same procedures for both the LH and RH sides. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Disengage the
More informationOVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
More informationED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
More information75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
More informationAll bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
More informationModel Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
More informationSide Window Glass Noise During Operation
T-SB-0077-12 May 21, 2012 Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2012 Camry, Camry HV Introduction Some 2012 Camry and Camry
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More informationTape the screwdriver tip before use. Using a screwdriver, remove the inside handle bezel.
Page 1 of 16 DISASSEMBLY 1. REMOVE DOOR INSIDE HANDLE BEZEL a. Using a screwdriver, open the cap. Tape the screwdriver tip before use. b. c. Remove the screw. Using a screwdriver, remove the inside handle
More informationRear Door: Service and Repair REAR DOOR
2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY
More informationPOWER MIRROR CONTROL SYSTEM
RROR POWER RROR CONTROL SYSTEM POWER RROR CONTROL SYSTEM BODY RROR PARTS LOCATION 1 DRIVER SIDE JUNCTION BLOCK - ACC FUSE - AM2 FUSE - ACC-B FUSE OUTER REAR VIEW RROR RH OUTER REAR VIEW RROR LH ACC RELAY
More informationREPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
More informationIR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
More informationROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
More informationTECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS DOOR SIDE AIRBAG SENSOR REPLACEMENT RX450h / RX350 / RX200t RX450h/RX350/RX200t Fr ドアエアバッグセンサ交換 一般 _v2.0 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION...
More information2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
More informationREASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
More informationA750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X
A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Last Modified: 4-26-2007 Service Category: Drivetrain 1.6 A Section: Automatic Transmission/Transaxle Model Year: 2007 Model:
More informationHeadlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
More informationOT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL
More informationSEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
More informationConflicts TOYOTA HIGHLANDER DUAL USB POWER DOCK. Part Number: Accessory Code:CP1000. Service Part Numbers.
Part Number: 00016-00222 Accessory Code:CP1000 Conflicts Note: Service Part Numbers Kit Contents Item # Quantity Req d Description 1 1 Dual USB Power Dock 2 General Applicability Hardware Bag Contents
More informationTelescopic Lever Detent Clip Replacement
T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained
More informationFRONT DOOR COMPONENTS
BO4 FRONT DOOR COMPONENTS BO5 ADJUSTMENT OF FRONT DOOR 1. ADJUST DOOR IN FORWARD /REARWARD AND VERTICAL DIRECTIONS Using SST, adjust the door by loosening the body side hinge bolts. SST 0981200010 2. ADJUST
More informationToyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52120 to complete the installation
More informationToyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52070 to complete the installation
More informationCode Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
More informationCOMPONENTS Toyota RAV ACCESSORIES & EQUIPMENT Front Seat - RAV4
2005 ACCESSORIES & EQUIPMENT Front Seat - RAV4 COMPONENTS Fig. 1: Identifying Front Seat Components & Torque Specifications FRONT SEAT ASSEMBLY REMOVAL CAUTION: Wear safety gloves, because the cutting
More information6/6/2018 2ZR-FXE Engine Mechanical: Camshaft: Removal 2012 Toyota Prius V MotoLogic
2012 Prius V REMOVAL REMOVE ENGINE ASSEMBLY WITH TRANSAXLE Report a problem with this article More Info INSTALL ENGINE STANDMore Info REMOVE ENGINE HANGERMore Info REMOVE THROTTLE BODY ASSEMBLYMore Info
More informationOVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE
7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor
More informationFRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
More informationARTICLE BEGINNING COMPONENTS FRONT DOOR Toyota Tacoma
Page 1 of 17 ARTICLE BEGINNING COMPONENTS Page 2 of 17 Fig. 1: Front Door Components (w/o Power Door Lock & Power Window Regulator) Page 3 of 17 Fig. 2: Front Door Components (W/ Power Door Lock & Power
More informationDISASSEMBLY REASSEMBLY
4 EXTERIOR FRONT BUMPER DISASSEMBLY 1. REMOVE HOOD TO FRONT END PANEL SEAL (a) Using a clip remover, detach the 8 clips and remove the panel seal. 2. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a clip
More information2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page 718 1. TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the
More informationBO 40 MOON ROOF COMPONENTS
BO40 BODY MOON ROOF COMPONENTS BODY BO41 ONVEHICLE INSPECTION INSPECT SLIDING ROOF GLASS ALIGNMENT (a) Start the engine and check the operation time of the sun roof. Operation time: Approx. 8 secs. (b)
More information(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector.
REMOVAL 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. 3. DISCHARGE FUEL SYSTEM PRESSURE
More informationSRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
More informationFRONT DOOR COMPONENTS
BO4 FRONT DOOR COMPONENTS BO5 COMPONENTS (Cont d) BO6 ADJUSTMENT OF FRONT DOOR 1. ADJUST DOOR IN FORWARD/REARWARD AND VERTICAL DIRECTIONS Using SST, adjust the door by loosening the body side hinge bolts.
More information10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationSCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)
Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel
More informationALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Page 1 of 9 Service and Repair FRONT WIPER MOTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM HEAD CAP a. Using a screwdriver wrapped with protective tape, remove
More informationPage 1 of 15 2011 Glass, Frames and Mechanisms - Rear Quarter Window Regulator Motor Removal and Installation Removal 1. Remove the rear quarter trim panels. For additional information, refer to: Rear
More informationLI 84 LIGHTING REAR COMBINATION LIGHT ASSEMBLY REMOVAL
84 GHTING REAR COMBINATION GHT ASSEMBLY REMOVAL HINT: Use the same procedure for both the RH and LH sides, unless otherwise specified. The procedure described below is for the LH side. 1. DISCONNECT CABLE
More informationSTEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
More informationTECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
More informationILLUSTRATION ILLUSTRATION
ILLUSTRATION ILLUSTRATION REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. When the brake pedal is depressed or the door courtesy switch is turned on even if the
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationKia Sedona. Installation Manual: Kia Sedona. Power Lift Gate System. Page 1 of 13
Kia Sedona Installation Manual: Kia Sedona Power Lift Gate System Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused
More informationThe driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
Page 1 of 19 DTC B1800/51 SHORT IN DRIVER SIDE SQUIB CIRCUIT; DTC B1801/51 OPEN IN DRIVER SIDE SQUIB CIRCUIT; DTC B1802/51 SHORT TO GND IN DRIVER SIDE SQUIB CIRCUIT; DTC B1803/51 SHORT TO B+ IN DRIVER
More information2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems
DESCRIPTION & OPERATION 2004 ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems WARNING: Accidental air bag deployment is possible. Personal injury may result. Read and follow all WARNINGS
More informationOVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
More informationConflicts. TOYOTA Prius XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA Prius 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4
More informationConflicts. Toyota Tacoma 2016 Frameless EC Mirror w/ Compass and HomeLink. Part Number: Accessory Code: ME4000
Toyota Tacoma 2016 Frameless EC Mirror w/ Compass and HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Conflicts Note: NONE Item # Quantity Reqd. Description 1 1 Frameless Mirror w/compass 2 1
More informationALLDATA Online Toyota Camry L4-2.4L (2AZ-FE) - Rear Strut Assembly. Rear Strut Assembly
Page 1 of 11 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Toyota Camry L4-2.4L (2AZ-FE) Conversion Calculator Vehicle
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationToyota Sienna. Installation Manual: Toyota Sienna. Power Lift Gate System. Page 1 of 12
Toyota Sienna Installation Manual: Toyota Sienna Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More information1 of 12 8/18/ :52 AM
1 of 12 8/18/2016 11:52 AM REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE a. Discharge fuel system pressure. 2. REMOVE DECK BOARD SUB-ASSEMBLY a. Disengage the 5 clips and turn up the front side of the deck
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationSEAT BELT WARNING SYSTEM
SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the
More informationConflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS
TOYOTA 4Runner 2010 - REARSIGHT Part Number: 00016-00085 Code: MC90 Conflicts KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA SIENNA LED DRL Black-Out
TOYOTA SIENNA 2013 - LED DRL Black-Out Part Number: 00016-08021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver
More informationINSTRUMENT PANEL ASSEMBLY. INSTRUMENT PANEL ASSEMBLY Component Parts Drawing IP-10 PFP:68200 AIS005BC PIIB0009E
INSTRUMENT PANEL ASSEMBLY Component Parts Drawing PFP:68200 AIS005BC PIIB0009E IP-10 1. Passenger air bag module 2. Front defroster grille (LH) 3. Front defroster grille (RH) 4. Cluster Lid A 5. Instrument
More informationGENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
More informationPart Number: TAV-713. Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL. Hardware Bag Contents.
Date: 09.04.2013 TOYOTA AVALON 2013 - LED DRL Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad
More informationPart Number: TCA-712SE
Date: 09.04.2013 TOYOTA CAMRY SE 2012-14 LED DRL Part Number: TCA-712SE Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2009 ACCORD 4-DOOR Publications No. AII 40008 Issue Date JULY 2008 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationRECOMMENDED SEQUENCE OF APPLICATION
TOYOTA CAMRY 2012- PART NUMBER: 250-8402 REARSIGHT KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE ADAPTER HARNESS 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS COLOR APPLICABILITY/TRIM
More informationConflicts NOTE: XLE, LE, AND SE MODELS
TOYOTA SIENNA 2011- REARSIGHT Part Number: 00016-00085 Accessory Code: MC9 Conflicts NOTE: XLE, LE, AND SE MODELS KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationInstallation Manual: Honda CRV Power Lift Gate System
Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Chassis Harness with RCA (Note: In some cases a RCA
More informationPS 53. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) REMOVAL
53 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 3. REMOVE FRONT WHEELS 4. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO. 1 5. REMOVE EXHAUST PIPE ASSEMBLY
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationGENERAL INFORMATION HANDLING PRECAUTIONS
BO1 BO2 GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS BO01M01 Taping When it is possible that the body or parts may be scratched during the operation, apply protection tape before starting
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationWater Leak in 3rd Row Seat Stow Area
T-SB-0214-12 November 1, 2012 Service Category Vehicle Exterior Section Exterior Panels/Trim Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2011 2012 Sienna Introduction Some 2011 2012
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More information2010 Toyota Prius Repair Manual
REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,
More informationBR 25 BRAKE HYDRAULIC BRAKE BOOSTER REMOVAL
AKE HYDRAULIC AKE BOOSTER 25 REMOVAL When installing, coat the parts indicated by arrows with lithium soap base glycol grease (See page - 13). As high pressure is applied to the brake actuator tube No.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory LED FOGLIGHT ATTACHMENT KIT P/N 08V70-MKC-A00 Application GL1800/B/BD/D/DA Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII
More informationXM Adapter Cable (P/N: ) MUST be used for this vehicle.
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description
More informationSCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA)
Preparation Part Number: PT296-12160 Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt (M5x8) 6 5 Wire tie (10 ) Hardware
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More information1. General Description
General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module
More informationRemoving and installing trim panel
Removing and installing trim panel vw-wi://rl/a.en-gb.a03.5106.29.wi::31914802.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing trim panel Removing Carefully prise out trim panel -1- in direction
More informationGROUP CONTENTS FRONT BUMPER ASSEMBLY WINDSHIELD WIPER AND WASHER REAR BUMPER ASSEMBLY REAR WIPER AND WASHER...
5- GROUP 5 CONTENTS FRONT BUMPER ASSEMBLY 5- REMOVAL AND INSTALLATION 5- DISASSEMBLY AND ASSEMBLY 5- REAR BUMPER ASSEMBLY 5-4 REMOVAL AND INSTALLATION 5-4 DISASSEMBLY AND ASSEMBLY 5-4 UNDER FLOOR SPARE
More informationPRIUS PRIME PRIUS PHV
PRIUS PRIME PRIUS PHV Plug-in Hybrid Gasoline-Electric Hybrid Synergy Drive ZVW52 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Toyota PRIUS PRIME,
More informationTOYOTA TACOMA INTERFACE KIT FOR IPOD Preparation
Preparation Part Number: PT545-00082 Kit Contents Item # Quantity Reqd. Description 1 1 Unit Assembly Kit 2 1 Mounting Kit 3 1 Hardware Bags 4 1 Unit and Fit Kit List 5 1 Owner s Manual Unit Assembly Kit
More informationConflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware
More informationPOWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
More information