10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic

Size: px
Start display at page:

Download "10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic"

Transcription

1 2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf) 2. DRAIN AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE) Torque: 25 N m (255 kgf cm, 18 ft lbf) 3. REMOVE FRONT WHEEL 4. REMOVE ENGINE UNDER COVER LH 300JO-03 Report a problem with this article 5. REMOVE FRONT AXLE HUB LH NUT (a) Using and a hammer, pry up the retaining tab of the hub LH nut Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged. (b) While applying the brakes, remove the hub LH nut. C57565 LH: 6. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and the clip, and separate the speed sensor front LH and the flexible hose from the shock absorber assy front LH. The positions of the bolt and clip on the right side differ from those on the left side. RH: F45379 F45378 F /12

2 (b) Remove the bolt, and separate the speed sensor front LH from the steering knuckle. Be careful not to damage the speed sensor. Prevent foreign matter from adhering to the speed sensor. C SEPARATE STABILIZER BAR FRONT (a) Hold the bolt with the spanner (10 mm) and remove the nut. (b) Remove the 2 cushion retainers No.1, the 2 cushions and separate the stabilizer bar front. C58069 D SEPARATE FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH (a) Remove the clip and the nut. (b) Using, separate the front suspension arm sub-assy lower No.1 LH from the steering knuckle F SEPARATE TIE ROD END SUB-ASSY LH (a) Remove the cotter pin and the nut. (b) Using, separate the tie rod end sub-assy LH from the steering knuckle D SEPARATE FRONT AXLE ASSY LH (a) Using a plastic hammer, separate the front drive shaft assy LH from the front axle assy LH. Be careful not to damage the boot. Be careful not to damage the speed sensor rotor. 2/12

3 11. REMOVE FRONT DRIVE SHAFT ASSY LH (a) Using, remove the front drive shaft assy LH. Be careful not to damage the oil seal and the boot. Be careful not to drop the drive shaft assy. C63075 D REMOVE FRONT DRIVE SHAFT ASSY RH (RH DRIVE SHAFT) (a) Using a brass bar and a hammer, remove the front drive shaft assy RH. Be careful not to damage the oil seal and the boot. Be careful not to drop the drive shaft assy. C FIX FRONT AXLE ASSY LH The hub bearing could be damaged if it is subjected to the vehicle s weight, such as when moving the vehicle with the drive shaft removed. Therefore, if it is necessary to place the vehicle s weight on the hub bearing, first support it with. C66796 D28938 N INSPECT FRONT DRIVE SHAFT ASSY LH Keep the drive shaft assy level during inspection. (a) Check that there is no remarkable play in the radial direction of the outboard joint. (b) Check if the inboard joint slides smoothly in the thrust direction. (c) Check that there is no remarkable play in the radial direction of the inboard joint. (d) Check the boots for damage. 3/12

4 One Touch Clamp Type: 15. REMOVE FRONT AXLE INBOARD JOINT BOOT LH NO.2 CLAMP (a) One Touch Clamp Type: Using a screwdriver, unclamp the inboard joint boot LH No.2 clamp as shown in the illustration. (b) Claw Engagement Type: Using needle nose pliers, remove the inboard joint boot LH No.2 clamp as shown in the illustration. Claw Engagement Type: C62539 C63307 D30655 One Touch Clamp Type: 16. REMOVE FRONT AXLE INBOARD JOINT BOOT LH CLAMP (a) One Touch Clamp Type: Using a screwdriver, unclamp the inboard joint boot LH clamp as shown in the illustration. (b) Claw Engagement Type: Using needle nose pliers, remove the inboard joint boot LH clamp as shown in the illustration. Claw Engagement Type: C63290 C63306 D SEPARATE FR AXLE INBOARD JOINT BOOT (a) Separate the inboard joint boot from the inboard joint assy LH. 4/12

5 18. REMOVE FRONT DRIVE INBOARD JOINT ASSY LH Matchmarks (a) Remove the old grease from the inboard joint assy LH. (b) Put matchmarks on the inboard joint assy LH and outboard joint shaft assy. Do not use a punch for marking. (c) Remove the inboard joint assy LH from the outboard joint shaft assy. F40222 (d) Using a snap ring expander, remove the inner LH shaft snap ring. C63291 D28939 Matchmarks One Touch Clamp Type: Claw Engagement Type: Brass Bar (e) Put matchmarks on the outboard joint shaft assy and the tripod joint assy. Do not use a punch for marking. (f) Using a brass bar and a hammer, remove the tripod joint assy from the outboard joint shaft assy. Do not tap the roller. F40224 (g) Remove the inboard joint boot LH No.2 clamp, the inboard joint boot and the inboard joint boot LH clamp. 19. REMOVE DRIVE SHAFT DAMPER SETTING CLAMP (RH DRIVE SHAFT) Use the following procedure for RH disassembly only. (a) One Touch Clamp Type: Using a screwdriver, unclamp the damper setting clamp as shown in the illustration. (b) Claw Engagement Type: Using needle nose pliers, remove the damper setting clamp as shown in the illustration. D /12

6 20. REMOVE DRIVE SHAFT DAMPER (RH DRIVE SHAFT) Use the following procedure for RH disassembly only. (a) Remove the drive shaft damper RH. 21. REMOVE FRONT AXLE OUTBOARD JOINT BOOT LH NO.2 CLAMP (a) Using a screwdriver, unclamp the outboard joint boot LH No.2 clamp. C REMOVE FRONT AXLE OUTBOARD JOINT BOOT LH CLAMP (a) Using a screwdriver, unclamp the outboard joint boot LH clamp. C REMOVE FRONT AXLE OUTBOARD JOINT BOOT (a) Remove the outboard joint boot from the outboard joint shaft assy. (b) Remove the old grease from the outboard joint. 24. REMOVE FRONT DRIVE SHAFT LH HOLE SNAP RING (a) Using a screwdriver, remove the LH hole snap ring. C REMOVE FRONT DRIVE SHAFT DUST COVER LH (a) Using and a press, remove the dust cover LH Be careful not to drop the inboard joint assy. G /12

7 26. INSTALL FRONT DRIVE SHAFT DUST COVER LH (a) Using and a press, install the dust cover LH. Be careful not to damage the dust cover. Dust cover should be installed completely. G INSTALL FRONT DRIVE SHAFT LH HOLE SNAP RING (a) Install a new LH hole snap ring. 28. INSTALL FRONT AXLE OUTBOARD JOINT BOOT (a) Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boot from being damaged. (b) Install the new parts on the inboard joint shaft assy in the following order. (1) Outboard joint boot LH No.2 clamp (2) Outboard joint boot (3) Outboard joint boot LH clamp (c) Pack the outboard joint assy LH with grease. Grease capacity: 155 to 170 g (5.5 to 6.1 oz.) (d) Install the outboard joint boot on the outboard joint shaft assy. Hold 29. INSTALL FRONT AXLE OUTBOARD JOINT BOOT LH Turn NO.2 CLAMP (a) Secure the outboard joint boot LH No.2 clamp onto the outboard joint boot. (b) Place onto the outboard joint boot LH No.2 clamp (c) Tighten the so that the outboard joint boot LH No.2 clamp is pinched. F40235 Do not overtighten the. (d) Using measure the clearance of the outboard joint boot LH No.2 clamp ( ) Clearance: 0.8 mm (0.031 in.) or less When the measured value exceeds the specified value, retighten the clamp. F /12

8 Hold 30. INSTALL FRONT AXLE OUTBOARD JOINT BOOT LH CLAMP (a) Mount drive shaft in a soft vise. (b) Secure the outboard joint boot LH clamp onto the outboard joint boot. (c) Place onto the outboard joint boot LH clamp Turn (d) Tighten the so that the outboard joint boot LH clamp F40237 is pinched. Do not overtighten the. (e) Using measure the clearance of the outboard joint boot LH clamp ( ) Clearance: 0.8 mm (0.031 in.) or less When the measured value exceeds the specified value, retighten the clamp. F INSTALL DRIVE SHAFT DAMPER (RH DRIVE SHAFT) Use the following procedure for RH disassembly only. (a) Install the drive shaft damper RH on the outboard joint shaft assy. 32. INSTALL DRIVE SHAFT DAMPER SETTING CLAMP (RH DRIVE SHAFT) Use the following procedure for RH disassembly only. (a) Install the damper setting clamp to the shaft. Be sure to install the clamp in the correct position. 8/12

9 One Touch Clamp Type: Claw Engagement Type: (b) One Touch Clamp Type: Using a screwdriver, install the damper setting clamp as shown in the illustration. (c) Claw Engagement Type: Using needle nose pliers, install the damper setting clamp as shown in the illustration. 33. INSTALL FRONT DRIVE INBOARD JOINT ASSY LH Before installing the boot, wrap the spline of the drive shaft with vinyl tape to prevent the boot from damaged. (a) Install the new parts on the outboard joint shaft assy in the following order. (1) Inboard joint boot LH clamp (2) Inboard joint boot (3) Inboard joint boot LH No.2 clamp D30599 Matchmarks F40227 (b) Align the matchmarks, install the tripod joint assy to the outboard joint assy. (c) Using a brass bar and a hammer, install the tripod joint assy. Do not tap the roller. Be sure to install the tripod joint in the correct direc- tion. (d) (e) Using a snap ring expander, install a new inner LH shaft snap ring. Apply grease to the inboard joint assy LH. Grease capacity: 125 to 135 g (4.5 to 4.8 oz.) C63291 D28939 Matchmarks (f) Align the matchmarks, install the inboard joint assy LH on the outboard joint shaft assy. F /12

10 34. INSTALL FR AXLE INBOARD JOINT BOOT (a) Install the inboard joint boot on the inboard joint assy and the outboard joint shaft assy. One Touch Clamp Type: 35. INSTALL FRONT AXLE INBOARD JOINT BOOT LH NO.2 CLAMP (a) One Touch Clamp Type: Using screwdriver, install the inboard joint boot LH No.2 clamp as shown in the illustration. (b) Claw Engagement Type: Using needle nose pliers, install the inboard joint boot LH No.2 clamp as shown in the illustration. Claw Engagement Type: D30658 One Touch Clamp Type: 36. INSTALL FRONT AXLE INBOARD JOINT BOOT LH CLAMP (a) One Touch Clamp Type: Using screwdriver, install the inboard joint boot LH clamp as shown in the illustration. (b) Claw Engagement Type: Using needle nose pliers, install the inboard joint boot LH clamp as shown in the illustration. Claw Engagement Type: D /12

11 N INSPECT FRONT DRIVE SHAFT Keep the drive shaft assy level during inspection. (a) Check that there is no remarkable play in the outboard joint. (b) Check if the inboard joint slides smoothly in the thrust direction. (c) Check that there is no remarkable play in the radial direction of the inboard joint. (d) Check the boots for damage. 38. INSTALL FRONT DRIVE SHAFT ASSY LH (a) M/T: Coat the spline of the inboard joint shaft assy with gear oil. (b) A/T:Coat the spline of the inboard joint shaft assy with ATF. (c) Align the shaft splines, install the drive shaft assy LH with a brass bar and a hammer. C63067 Set the hole snap ring with the opening side facing down. Be careful not to damage the boot and the oil seal. Whether the inboard joint shaft is in contact with the pinion shaft or not can be known from the sound or feeling when driving it in. 39. INSTALL FRONT DRIVE SHAFT ASSY RH (RH DRIVE SHAFT) Apply the same procedure to the RH. Set the hole snap ring with the opening side facing down. Be careful not to damage the boot and the oil seal. 40. INSTALL FRONT AXLE ASSY LH (a) Install the drive shaft assy LH to the front axle assy LH. Be careful not to damage the outboard joint boot. Be careful not to damage the speed sensor rotor. Do not excessively push the front axle assy LH. 41. INSTALL TIE ROD END SUB-ASSY LH (a) Install the tie rod end sub-assy LH to the steering knuckle with the nut. Torque: 49 N m (500 kgf cm, 36 ft lbf) (b) Install a new cotter pin. If the holes for the cotter pin are not aligned, tighten the nut up to INSTALL FRONT SUSPENSION ARM SUB-ASSY LOWER NO.1 LH (a) Install the tie front suspension arm sub-assy lower No.1 LH to the steering knuckle with the nut. Torque: 98 N m (1,000 kgf cm, 72 ft lbf) (b) Install a new clip. If the holes for the clip are not aligned, tighten the nut up to /12

12 D INSTALL STABILIZER BAR FRONT (a) Install the stabilizer bar front with 2 cushion retainers No.1, 2 cushions and the nut, as shown in the illustration. Be sure to install the cushion and retainer in the correct direction. (b) Torque the nut with the spanner (10mm). Torque: 18 N m (184 kgf cm, 13 ft lbf) LH: 44. INSTALL SPEED SENSOR FRONT LH (a) Install the speed sensor front LH and the flexible hose on the shock absorber assy front LH with the bolt and clip. Torque: 29 N m (300 kgf cm, 22 ft lbf) The positions of the bolt and clip on the right side differ from those of the left side. RH: F45379 F45378 F45754 (b) Install the speed sensor front LH on the steering knuckle with the bolt. Torque: 8.0 N m (82 kgf cm, 71 in. lbf) Be careful not to damage the speed sensor. Keep the speed sensor clean. Do not twist the sensor wire when installing the speed sensor. C INSTALL FRONT AXLE HUB LH NUT (a) Install a new hub LH nut. Torque: 216 N m (2,200 kgf cm, 159 ft lbf) (b) Using a chisel and a hammer, stake the hub LH nut. C INSTALL ENGINE UNDER COVER LH 47. INSTALL FRONT WHEEL Torque: 103 N m (1,050 kgf cm, 76 ft lbf) 48. ADD MANUAL TRANSAXLE OIL (M/T TRANSAXLE) 49. INSPECT AND ADJUST MANUAL TRANSAXLE OIL (M/T TRANSAXLE) (See page 41-2 ) 50. ADD AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE) 51. INSPECT AND ADJUST AUTOMATIC TRANSAXLE FLUID (A/T TRANSAXLE) (See page 40-2 ) 52. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See page 26-7 ) 53. CHECK ABS SPEED SENSOR SIGNAL (See page ) Portions of materials contained herein have been reprinted under license from Toyota Motor Sales, U.S.A., Inc., License Agreement TMS /12

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy. OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,

More information

FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR

FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH

More information

FRONT AXLE HUB SUB-ASSY LH

FRONT AXLE HUB SUB-ASSY LH 3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)

More information

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 6 REMOVAL & INSTALLATION AXLE SHAFTS Removal Raise and support vehicle. Remove front wheels. Remove engine undercovers. Remove cotter pin and lock nut cap. See Fig. 2. Apply brakes and remove

More information

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS AXLE SHAFTS - 2.2L 1994 Toyota Celica 1994 DRIVE AXLES Toyota FWD Axle Shafts Celica 2.2L 4 Cyl DESCRIPTION Axle shafts transfer power from transaxle to the front wheels. Axle shaft consists of axle shaft

More information

REAR DRIVE SHAFT (3S GTE ENGINE)

REAR DRIVE SHAFT (3S GTE ENGINE) SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,

More information

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension

More information

FRONT AXLE AND SUSPENSION FA 1

FRONT AXLE AND SUSPENSION FA 1 FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated

More information

REPLACEMENT 1. REMOVE FRONT WHEEL

REPLACEMENT 1. REMOVE FRONT WHEEL 3028 REPLACEMENT 1. REMOVE FRONT WHEEL 300HC03 2. REMOVE FRONT DISC BRAKE CALIPER ASSY LH (a) Remove the bolt and separate the brake tube bracket from the steering knuckle. (b) Using, disconnect the brake

More information

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1 AXLE AXLE SYSTEM 1 AXLE SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of probability of each of the possible causes.

More information

5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.

5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover. 5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:

More information

SA 8 FRONT AXLE HUB COMPONENTS

SA 8 FRONT AXLE HUB COMPONENTS SA8 FRONT AXLE HUB COMPONENTS SA9 REMOVAL OF FRONT AXLE HUB 1. REMOVE COTTER PIN, LOCK NUT CAP AND BEARING LOCK NUT (a) Remove the cotter pin and lock nut cap. (b) Loosen the bearing lock nut while depressing

More information

SUSPENSION AND AXLE SA 1

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the

More information

DRIVE SHAFT LOCATION INDEX

DRIVE SHAFT LOCATION INDEX DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,

More information

DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL

DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) 15 REMOVAL 1. REMOVE FRONT WHEELS 2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY (a) Remove the 6 bolts and engine under cover assembly. 3.

More information

REAR AXLE AND SUSPENSION RA 1

REAR AXLE AND SUSPENSION RA 1 REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to

More information

). 1. REMOVE FR WIPER ARM RH

). 1. REMOVE FR WIPER ARM RH 5120 OVERHAUL When installing, apply power steering fluid or molybdenum disulfide lithium base grease to the parts indicated by arrows (See page 5117). 1. REMOVE FR WIPER ARM RH (See page 666) 2. REMOVE

More information

2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE)

2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) 2004 Toyota Truck Tundra 4WD V8 4.7L (2UZ FE) Vehicle» Steering and Suspension» Steering» Steering Gear» Service and Repair» Disassembly and Assembly Part 1 Of 3 Part 2 Of 3 http://alldatapro.com/alldata/pro~v432223842~c41100~r0~od~n/0/101825161/103142888/105946035/110859872/34853741/34864218/34864219/34864308/

More information

PS 53. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) REMOVAL

PS 53. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) REMOVAL 53 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 3. REMOVE FRONT WHEELS 4. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO. 1 5. REMOVE EXHAUST PIPE ASSEMBLY

More information

POWER STEERING SYSTEM

POWER STEERING SYSTEM SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system

More information

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS 2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When

More information

Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out)

Symptom Suspect Area See page. 3. Shock absorber (Worn out) 3. Shock absorber (Worn out) TROUBLESHOOTING PROBLEM SYMPTOMS TABLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part

More information

PROPELLER SHAFT PR 1

PROPELLER SHAFT PR 1 PR1 PR2 PREPARATION PREPARATION SST (SPECIAL SERVICE TOOLS) 0932520010 Transmission Oil Plug 2JZGE M/T 0932540010 Transmission Oil Plug 2JZGE A/T 0933000021 Companion Flange Holding Tool 0933050010 Propeller

More information

1. General Description

1. General Description General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Propeller shaft type 3UJ Front propeller shaft Joint-to-joint length: L 1 mm (in) 633 (24.92) Rear propeller shaft Joint-to-Joint

More information

1. General Description

1. General Description General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Model All models Propeller shaft type EDJ Front propeller shaft Joint-to-joint length: L 1 mm (in) AT 735.5 (28.96) MT 675.5

More information

2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX

2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX 2001 FORESTER SERVICE MANUAL QUICK REFERENCE INDEX CHASSIS SECTION This service manual has been prepared to provide SUBARU service personnel with the necessary information and data for the correct maintenance

More information

Technical Service BULLETIN

Technical Service BULLETIN Technical Service BULLETIN September 12, 2002 Title: Models: 00 05 Tundra BR004-02 BRAKES TSB REVISION NOTICE: April 4, 2005: Applicable Vehicles has been updated to include 2003 2005 model years. The

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

4. Front and Rear Drive Shafts

4. Front and Rear Drive Shafts 4-2 SERVICE PROCEDURE 3. Rear Axle (FWD) - Tightening torque: 186±20 N m (19±2 kg-m, 137±14 ft-lb) Use a new axle nut. Always tighten axle nut before installing wheel on vehicle. If wheel is installed

More information

5. Front Drive Shaft FRONT DRIVE SHAFT. B: INSTALLATION 1) Insert the BJ into hub splines.

5. Front Drive Shaft FRONT DRIVE SHAFT. B: INSTALLATION 1) Insert the BJ into hub splines. 5. Front Drive Shaft A: REMOVAL 1) Jack-up the vehicle, support it with rigid racks, and then remove the front wheel cap and wheels. 2) Raise the caulking portion of axle nut. 3) Depress the brake pedal

More information

PS 37. POWER STEERING POWER STEERING LINK (for 4WD) REMOVAL

PS 37. POWER STEERING POWER STEERING LINK (for 4WD) REMOVAL POWER STEERING POWER STEERING LINK (for 4WD) 37 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 3. REMOVE FRONT WHEELS 4. REMOVE NO. 1 ENGINE UNDER

More information

REPLACEMENT. 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FAN AND GENERATOR V BELT (See page 14 4)

REPLACEMENT. 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FAN AND GENERATOR V BELT (See page 14 4) 5540 550JH01 REPLACEMENT HINT: COMPONENTS: See page 5539 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page 5511) SST 0711058060 (0711758080, 0711758090, 0711778050, 0711788060, 0711788070, 0711788080)

More information

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS...

POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS... TO INDEX STEERING POWER STEERING POWER STEERING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................

More information

Power Steering Rack Leak from Right Side: Overhaul Procedure

Power Steering Rack Leak from Right Side: Overhaul Procedure T-SB-0030-14 April 17, 2014 Power Steering Rack Leak from Right Side: Overhaul Procedure Service Category Steering Section Steering Gear/Linkage Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION

More information

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS

More information

DRIVE SHAFT SYSTEM DS

DRIVE SHAFT SYSTEM DS DS Page 1. General Description...2 2. Propeller Shaft...14 3. Front Axle...17 4. Rear Axle...23 5. Front Drive Shaft...31 6. Rear Drive Shaft...37 7. General Diagnostic Table...43 1. General Description

More information

Title: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides)

Title: FRONT BRAKE VIBRATION Models: Tundra. Front Brake Caliper & Rotor Replacement (2WD, Both Sides) Technical Service BULLETIN September 16, 2002 Title: FRONT BRAKE VIBRATION Models: 00-03 Tundra BR004-02 BRAKES TSB REVISION NOTICE: S March 5, 2004: A torque speification on page 10, step 24, was changed.

More information

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( ) Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls

More information

JOINT SHAFT REMOVAL/INSTALLATION

JOINT SHAFT REMOVAL/INSTALLATION 2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed

More information

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica

More information

COMPONENTS (KOYO Type)

COMPONENTS (KOYO Type) STEERING SR55 COMPONENTS (KOYO Type) DISASSEMBLY OF STEERING GEAR HOUSING 1. CLAMP GEAR HOUSING IN VISE Using SST, secure the steering gear in a vise. SST 0961200012 2. REMOVE RIGHT AND LEFT TURN PRESSURE

More information

6. Rear Drive Shaft REAR DRIVE SHAFT

6. Rear Drive Shaft REAR DRIVE SHAFT DRIVE SHAFT SYSTEM 6. Rear Drive Shaft A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 7) Remove the bolts which secure

More information

PS 60. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) INSPECTION

PS 60. POWER STEERING POWER STEERING LINK (for 4WD and Pre-Runner) INSPECTION 60 ZK08184E01 INSPECTION 1. INSPECT TIE ROD END SUB-ASSEMBLY (a) Flip the ball joint stud back and forth 5 times as shown in the illustration before installing the nut. (b) Using a torque wrench, turn

More information

Steering Gear: Service and Repair POWER STEERING GEAR BOX

Steering Gear: Service and Repair POWER STEERING GEAR BOX 2003 Kia Truck Sorento V6-3.5L Copyright 2013, ALLDATA 10.52 Page 1 Steering Gear: Service and Repair POWER STEERING GEAR BOX COMPONENTS REMOVAL 1. Drain the power steering fluid. 2. Disconnect the pressure

More information

STEERING SYSTEM - MANUAL RACK & PINION

STEERING SYSTEM - MANUAL RACK & PINION STEERING SYSTEM - MANUAL RACK & PINION 1993 Nissan Sentra 1993 STEERING Nissan Manual Rack & Pinion NX, Sentra DESCRIPTION & OPERATION Steering gear assembly is a manual rack and pinion type. Unit is mounted

More information

OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE

OVERHAUL. NOTICE: Do not apply grease to each sliding part of the link. HINT: COMPONENTS: See page REMOVE REAR FLOOR FINISH PLATE 7528 ENGINE HOOD/DOOR OVERHAUL NOTICE: Do not apply grease to each sliding part of the link. COMPONENTS: See page 7526 7506701 1. REMOVE REAR FLOOR FINISH PLATE Using a screwdriver, remove the rear floor

More information

FRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2

FRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2 FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3

More information

Steering Knuckle (See page SA 35)

Steering Knuckle (See page SA 35) SA40 SUSPENSION AND AXLE Steering Knuckle (See page SA35) REMOVAL OF STEERING KNUCKLE 1. REMOVE DISC BRAKE CYLINDER AND FRONT AXLE HUB (See page SA36) 2. REMOVE DUST COVER AND OIL SEAL 3. DISCONNECT KNUCKLE

More information

DRIVE SHAFT & FRONT AXLE

DRIVE SHAFT & FRONT AXLE DRIVE SHAFT & FRONT AXLE Return To Main Table of Contents GENERAL... 2 DRIVE SHAFT... 6 HUB AND KNUCKLE... 13 FRONT AXLE... 15 GENERAL GENERAL SPECIFICATIONS Drive shaft Joint type Outer Inner Length (Joint

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front

ALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle

More information

Page 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).

More information

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder.

OVERHAUL NOTICE: 7. REMOVE BRAKE MASTER CYLINDER (a) Disconnect the 5 connectors from brake master cylinder. OVERHAUL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 40 times. HINT: When a pressure in power supply system is released, reaction force become

More information

7 Drive Shaft and Axle

7 Drive Shaft and Axle 7 Drive Shaft and Axle 7.1 General SPECIFICATIONS EITC0100 Drive-shaft Joint type M/T AT Outer B.J. B.J. Inner T.J. T.J. Length (Joint to joint) mm (in.) Left 380 (14.96) 349 (13.74) Right 593 (23.35)

More information

FRONT AXLE GROUP CONTENTS GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS DRIVE SHAFT ASSEMBLY SPECIAL TOOLS...

FRONT AXLE GROUP CONTENTS GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS DRIVE SHAFT ASSEMBLY SPECIAL TOOLS... 26-1 GROUP 26 CONTENTS GENERAL DESCRIPTION 26-2 DIAGNOSIS 26-2 TROUBLESHOOTING STRATEGY 26-2 SYMPTOM CHART 26-3 SYMPTOM PROCEDURES 26-3 SPECIAL TOOLS 26-4 ON-VEHICLE SERVICE 26-6 WHEEL BEARING END PLAY

More information

FRONT AXLE GROUP CONTENTS DRIVE SHAFT ASSEMBLY GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS SPECIAL TOOLS...

FRONT AXLE GROUP CONTENTS DRIVE SHAFT ASSEMBLY GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS SPECIAL TOOLS... 26-1 GROUP 26 CONTENTS GENERAL DESCRIPTION 26-2 DIAGNOSIS 26-3 TROUBLESHOOTING STRATEGY 26-3 SYMPTOM CHART 26-3 SYMPTOM PROCEDURES 26-4 SPECIAL TOOLS 26-5 ON-VEHICLE SERVICE 26-8 WHEEL BEARING END PLAY

More information

DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION

DF 78. HINT: Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 78 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) Face the rough side of the thrust washer marked by # to the differential case. INSPECTION 1. DIFFERENTIAL SIDE GEAR (w/ LSD Differential)

More information

4. Rear Axle REAR AXLE

4. Rear Axle REAR AXLE REAR AXLE DRIVE SHAFT SYSTEM 4. Rear Axle A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 4) Remove the axle nut using

More information

TO INDEX DIFFERENTIAL FRONT DIFFERENTIAL CARRIER OIL SEAL (4WD) FRONT DIFFERENTIAL CARRIER ASSEMBLY (4WD) REAR DIFFERENTIAL CARRIER OIL SEAL

TO INDEX DIFFERENTIAL FRONT DIFFERENTIAL CARRIER OIL SEAL (4WD) FRONT DIFFERENTIAL CARRIER ASSEMBLY (4WD) REAR DIFFERENTIAL CARRIER OIL SEAL TO INDEX DRIVE LINE / AXLE DIFFERENTIAL DIFFERENTIAL SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................

More information

Overhaul Special Tools Required

Overhaul Special Tools Required 1 of 31 Overhaul - Special Tools Required - Cylinder end seal remover attachment, 07NAD-SR3020A - Pilot collar, 07GAF-PH70100 - Valve seal ring sizing tool, 07NAG-SR3090A - Ball joint boot clip guide,

More information

PRECAUTION TROUBLESHOOTING

PRECAUTION TROUBLESHOOTING STEERING SR1 SR2 PRECAUTION Care must be taken to replace parts properly because they could affect the performance of the steering system and result in a driving hazard. The steering wheel pad has an SRS

More information

If it exceeds the maximum specification, replace the propeller shaft.

If it exceeds the maximum specification, replace the propeller shaft. If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown

More information

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch: 20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag

More information

FRONT AXLE 26-1 CONTENTS ON-VEHICLE SERVICE... 5 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 HUB AND KNUCKLE ASSEMBLY...

FRONT AXLE 26-1 CONTENTS ON-VEHICLE SERVICE... 5 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 HUB AND KNUCKLE ASSEMBLY... 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 3 LUBRICANTS... 3 SPECIAL TOOLS... 3 ON-VEHICLE SERVICE... 5 Wheel Bearing Axial Play Check... 5 Hub bolt replacement... 5 HUB

More information

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement 2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,

More information

FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3

FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3 TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SYMPTOM DIAGNOSIS... 2 NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart...2 PRECAUTION... 3 PRECAUTIONS...

More information

SA 66 Front Differential (Disassembly and Assembly of Differential w/o A D D ) Disassembly and Assembly of Differential (with out A.D.D.

SA 66 Front Differential (Disassembly and Assembly of Differential w/o A D D ) Disassembly and Assembly of Differential (with out A.D.D. SA66 SUSPENSION AND AXLE Differential w/o A D D ) Disassembly and Assembly of Differential (with out A.D.D.) SUSPENSION AND AXLE Differential w/o A D D ) DISASSEMBLY OF DIFFERENTIAL 1. REMOVE DIFFERENTIAL

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final

More information

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX FRONT AXLE D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools (SST)... 3 Commercial Service Tools... 5 NOISE, VIBRATION AND

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)

More information

DF 43 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

DF 43 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY 43 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID 4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (See page

More information

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1. 2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page

More information

2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE)

2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) ALLDATA Repair - 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) - Service and R... Page 1 of 12 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Vehicle» Powertrain Management» Fuel Delivery and Air Induction»

More information

Page 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following

More information

DF 47 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

DF 47 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL 47 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID Immediately wash off any brake fluid that comes into contact with any painted surfaces. 4. DRAIN

More information

2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.

2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1. 4-2 [W2A1] SERVICE PROCEDURE 9) Install tie-rod end ball joint on housing knuckle arm. 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.8 (1) Cotter pin (2) Castle nut (3) Tie-rod B4M2214B 10) While depressing brake

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

FRONT AXLE SECTION FAX CONTENTS DRIVELINE/AXLE FAX-1 SERVICE INFORMATION... 2

FRONT AXLE SECTION FAX CONTENTS DRIVELINE/AXLE FAX-1 SERVICE INFORMATION... 2 DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Caution...2 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3 NOISE, VIBRATION AND

More information

STEERING SYSTEM - MANUAL

STEERING SYSTEM - MANUAL Article Text ARTICLE BEGINNING 1991-92 STEERING Chrysler Motors/Mitsubishi - Manual Steering - Rack & Pinion Dodge; Colt, Colt Vista, Colt 200, Eagle; Summit Mitsubishi; Eclipse, Mirage, Precis DESCRIPTION

More information

1984 Dodge W250 PICKUP

1984 Dodge W250 PICKUP 1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as

More information

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.

OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 4168 OVERHAUL 410F701 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 to 0.40 mm (0.0039 to 0.0157 in.) 0.40 mm (0.0157 in.) C80538 2. INSPECT

More information

PROPELLER SHAFT ASSEMBLY

PROPELLER SHAFT ASSEMBLY PR2 PROPELLER SHAFT COMPONENTS PR03I02 Front propeller shaft 80 (820, 59) 80 (820, 59) Front Propeller Shaft Transfer Front Differential 80 (820, 59) 80 (820, 59) No.2 Engine Under Cover Rear propeller

More information

DRAIN BRAKE FLUID NOTICE:

DRAIN BRAKE FLUID NOTICE: REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.

More information

3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17

3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17 FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within

More information

NewtonNet. Driveshaft and Axle

NewtonNet. Driveshaft and Axle GENERAL SPECIFICATIONS... DS-2 LUBRICANTS... DS-3 SPECIAL TOOLS...DS-3 TROUBLESHOOTING...DS-5 DRIVESHAFT FRONT DRIVESHAFT ASSEMBLY COMPONENTS...DS-6 REMOVAL...DS-6 INSPECTION... DS-8 INSTALLATION...DS-8

More information

SR 55 POWER STEERING GEAR. POWER STEERING GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown.

SR 55 POWER STEERING GEAR. POWER STEERING GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown. STEERING SR55 GEAR GEAR REMOVAL AND INSTALLATION Remove and install the parts, as shown. SR56 STEERING MAIN POINT OF REMOVAL AND INSTALLATION 1. REMOVE OIL RESERVOIR 2. REMOVE AIR CLEANER ASSEMBLY 3. DISCONNECT

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions... 2 PREPARATION...

More information

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system. 2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the

More information

23.Front Differential Assembly

23.Front Differential Assembly 23.Front Differential Assembly A: REMOVAL 1) Remove the manual transmission assembly. 2) Prepare the transmission for overhaul.

More information

DRAIN BRAKE FLUID NOTICE:

DRAIN BRAKE FLUID NOTICE: OVERHAUL Overhaul procedure of the RH side is the same as that of with LH side. 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID Wash off the brake fluid immediately if it comes into contact with a painted surface.

More information

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.

More information

FRONT SUSPENSION SYSTEM

FRONT SUSPENSION SYSTEM SYSTEM PROBLEM SYMPTOMS TABLE SYSTEM Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the problem. Check each part in order. If necessary,

More information

SR 75. Power Steering (Gear Housing) Gear Housing (4WD) REMOVAL AND INSTALLATION OF GEAR HOUSING Remove and install the parts as shown.

SR 75. Power Steering (Gear Housing) Gear Housing (4WD) REMOVAL AND INSTALLATION OF GEAR HOUSING Remove and install the parts as shown. STEERING SR75 Gear Housing (4WD) REMOVAL AND INSTALLATION OF GEAR HOUSING Remove and install the parts as shown. SR76 STEERING (MAIN POINT OF REMOVAL AND INSTALLATION) 1. REMOVE RESERVOIR TANK 2. REMOVE

More information

EM-81 EM0Z7-01 DISASSEMBLY

EM-81 EM0Z7-01 DISASSEMBLY EM81 EM0Z701 DISASSEMBLY 1. M/T: REMOVE FLYWHEEL 2. A/T: REMOVE DRIVE PLATE 3. REMOVE REAR END PLATE 4. INSTALL ENGINE TO ENGINE STAND FOR DIS ASSEMBLY 5. REMOVE TIMING BELT AND PULLEYS (See page EM13

More information

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS (NVH)

More information

SA 82 Front Differential (Disassembly and Assembly of Differential w/ ADD) Disassembly and Assembly of Differential (with A.D.D.)

SA 82 Front Differential (Disassembly and Assembly of Differential w/ ADD) Disassembly and Assembly of Differential (with A.D.D.) SA82 SUSPENSION AND AXLE Disassembly and Assembly of Differential (with A.D.D.) DISASSEMBLY OF DIFFERENTIAL 1. REMOVE ACTUATOR (a) Remove the four bolts. (b) Using a hammer, remove the actuator. SA83 2.

More information