A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X
|
|
- Cornelius Bell
- 5 years ago
- Views:
Transcription
1 A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) Last Modified: Service Category: Drivetrain 1.6 A Section: Automatic Transmission/Transaxle Model Year: 2007 Model: 4Runner Doc ID: RM000002BHN007X Title: A750F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY: REMOVAL (2007 4Runner) REMOVAL 1. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY 2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY 3. REMOVE NO.1 CONSOLE UPPER PANEL GARNISH 4. REMOVE NO.2 CONSOLE UPPER PANEL GARNISH 5. REMOVE REAR CONSOLE BOX ASSEMBLY 6. REMOVE FLOOR SHIFT ASSEMBLY (a) Disconnect the 2 connectors and 2 clamps. (b) Remove the lock plate and disconnect the transmission control cable. (c) Remove the 4 bolts and floor shift assembly.
2 Last Modified: Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2007 Model: 4Runner Doc ID: RM000002AUE005X Title: REMOVAL 1. BOLT, SCREW AND NUT TABLE HINT: The bolts, screws and nuts, which are necessary for installation and removal of the instrument panel are shown in the illustration below and the text with alphabets. 2. DISCONNECT BATTERY NEGATIVE TERMINAL HINT: 3. REMOVE INSTRUMENT PANEL FINISH PLATE
3 (a) Remove the instrument panel finish plate. 4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (a) Remove the 2 bolts <B>. (b) Disconnect the hood lock control cable assembly and fuel lid lock control cable sub-assembly. (c) Disengage the 4 clips. (d) Disconnect the connectors and remove the lower instrument panel finish panel sub-assembly. 5. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (a) Disengage the 5 clips and 2 claws, and remove the console upper rear panel, and then disconnect the connectors. 6. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (a) Disengage the 6 clips and 2 claws, and then remove the upper console panel sub-assembly.
4 NOTICE: Be careful not to snap the claws during the operation. 7. REMOVE NO. 1 CONSOLE UPPER PANEL GARNISH (a) Disengage the clip. (b) Pull the No. 1 console upper panel garnish rearward to be removed. 8. REMOVE NO. 2 CONSOLE UPPER PANEL GARNISH 9. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (a) Remove the screw. (b) Disengage the 4 clips and remove the air conditioner, and then disconnect the connectors.
5 10. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (a) Remove the 3 bolts <C>. (b) Disengage the 8 clips and remove the center instrument cluster finish panel sub-assembly. 11. REMOVE RADIO RECEIVER ASSEMBLY (w/ Bracket) 12. REMOVE NO. 2 LOWER STEERING WHEEL COVER 13. REMOVE NO. 3 LOWER STEERING WHEEL COVER 14. REMOVE STEERING PAD 15. REMOVE STEERING WHEEL ASSEMBLY 16. REMOVE UPR STEERING COLUMN COVER 17. REMOVE TURN SIGNAL SWITCH ASSEMBLY (w/ Bracket) 18. REMOVE INSTRUMENT PANEL LOWER LH (a) Remove the 2 bolts <B>.
6 (b) Disengage the 2 claws and remove the instrument panel lower LH. 19. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (a) Disengage the 7 clips. (b) Disconnect the connectors and remove the instrument cluster finish panel sub-assembly. 20. REMOVE COMBINATION METER ASSEMBLY 21. REMOVE REAR CONSOLE BOX ASSEMBLY (a) Disconnect the connectors. (b) Remove the 6 bolts <B> and rear console box assembly. 22. REMOVE FRONT DOOR SCUFF PLATE RH 23. REMOVE COWL SIDE TRIM BOARD RH
7 (a) Remove the clip. (b) Disengage the 2 claws and remove the cowl side trim board RH. 24. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (a) Remove the screw <E>. (b) Disengage the 3 clips and remove the No. 2 instrument panel under cover sub-assembly. 25. REMOVE GLOVE COMPARTMENT DOOR SUB-ASSEMBLY (a) Remove the screw <F> and glove compartment door. (b) Deform the upper part of the glove compartment door to release the stoppers. (c) Pull the glove compartment door upward to remove it. 26. DISCONNECT PASSENGER AIRBAG CONNECTOR 27. REMOVE NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL
8 (a) Remove the 4 screws <E>. (b) Disengage the 2 claws and remove the instrument panel finish panel. 28. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (a) Remove the screw <G>. (b) Disengage the 2 clips and 2 claws, and then remove the No. 2 instrument panel register assembly. 29. REMOVE ASSIST GRIP SUB-ASSEMBLY 30. REMOVE FRONT PILLAR GARNISH LH (a) Using a screwdriver, remove the 2 assist grip plugs. HINT: Tape the screwdriver tip before use. (b) Remove the 2 bolts. (c) Using a screwdriver, disengage the claw. Remove the clip labeled A, clip labeled B and pillar garnish. 31. REMOVE FRONT PILLAR GARNISH RH
9 HINT: Use the same procedure described for the LH side. 32. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY (a) Remove the 9 bolts <A> <B> <C> and nut <H>. (b) Disconnect the connectors. (c) Remove the instrument panel safety pad sub-assembly. 33. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (a) Using a moulding remover, disengage the 4 clips and remove the No. 1 instrument panel speaker panel sub-assembly. 34. REMOVE FRONT STEREO COMPONENT SPEAKER ASSEMBLY
10 (a) Remove the 2 screws <D> and the front stereo component speaker assembly. 35. REMOVE NO. 1 INSTRUMENT PANEL PIN (a) Remove the screw <D> and the No. 1 instrument panel pin. 36. REMOVE DEFROSTER NOZZLE ASSEMBLY (a) Remove the 2 screws <D> and the defroster nozzle assembly. 37. REMOVE NO. 2 HEATER TO REGISTER DUCT (a) Remove the 5 screws <D> and the No. 2 heater to register duct. 38. REMOVE NO. 1 METER HOOD RETAINER (a) Remove the screw <D> and the No. 1 meter hood retainer. 39. REMOVE CENTER INSTRUMENT PANEL BRACKET SUB-ASSEMBLY (a) Remove the screw <D> and the center instrument panel bracket sub-assembly. 40. REMOVE AUTOMATIC LIGHT CONTROL SENSOR (a) Disconnect the connector. (b) Remove the automatic light control sensor. 41. REMOVE COOLER (SOLAR SENSOR) THERMISTOR (a) Disconnect the connector. (b) Remove the cooler (solar sensor) thermistor. 42. REMOVE NO. 2 INSTRUMENT PANEL WIRE 43. REMOVE ANTENNA CORD SUB-ASSEMBLY 44. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System) 45. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH (a) Remove the 3 screws <D> and the instrument cluster finish panel garnish. 46. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY 47. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
More information2. DISCONNECT BATTERY NEGATIVE TERMINAL (See page 60 1) 3. REMOVE SHIFT LEVER KNOB SUB ASSY 4. REMOVE SHIFT LEVER KNOB SUB ASSY
7112 INSTRUMENT PANEL/METER 710DV02 REPLACEMENT HINT: COMPONENTS: See page 718 1. TABLE OF BOLT, SCREW AND NUT HINT: The bolts, screws and nuts, which are necessary for installation and removal of the
More informationModel Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
More informationCode Shape Code Shape. φ = 6 (0.31) (0.24) (A) (B) (C) L = 18 L = 20 (0.71) φ = 5 (0.24) (0.20) (D) (E) (F) L = 16 L = 14 (0.63)
7110 INSTRUMENT PANEL/METER 7108S01 REPLACEMENT HINT: COMPONENTS: See page 717 1. TABLE OF BOLT, SCREW AND NUT HINT: Indicate the bolts, screws and nuts, which are necessary for installation and removal
More informationDISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More informationRemoval and Installation
Page 1 of 14 Removal and Installation Work item table PARTS INSTRUMENT PANEL ASSEMBLY COMBINATION METER DISPLAY UNIT AV control unit CENTER CONSOLE ASSEMBLY Rear console assembly [1] [1] Instrument garnish
More informationON-VEHICLE INSPECTION
51 Connector Front Side: A5 ON-VEHICLE INSPECTION 1. INSPECT TOWING CONVERTER RELAY (a) Measure the voltage and check the result in accordance with the value(s) in the table below. Standard E064833E01
More informationREMOVAL. 6. REMOVE LOWER FINISH PANEL Using a screwdriver, remove the lower finish panel. HINT: Tape the screwdriver tip before use.
BO90 REMOVAL 1. REMOVE FRONT SEATS (See page BO105 or BO1 12) 2. REMOVE FRONT DOOR WEATHERSTRIPS 3. REMOVE FRONT PILLAR GARNISHES 4. REMOVE STEERING WHEEL PAD (See page SR14 ) 5. REMOVE COLUMN COVERS BO2PV02
More informationREMOVAL AND INSTALLATION
501-01-1 Body System Interior 501-01-1 REMOVAL AND INSTALLATION Instrument Panel CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
More informationROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
More informationIR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
More informationREPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
More informationRemoval & Installation
Page 1 of 11 2011 Nissan Rogue : Body > Interior > Instrument Panel > Removal & Installation Removal & Installation 1. Before servicing the vehicle, refer to the Precautions Section. CAUTION Always work
More informationED 13. ENGINE HOOD / DOOR FRONT DOOR (w/ Power Window) DISASSEMBLY
13 B088092E01 DISASSEMBLY Use the same procedures for both the LH and RH sides. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Disengage the
More informationSymptom Suspect Area See page 1. Wire Harness or Connector 2. ECM 2. ECM. 1. Wire Harness or Connector 2. Skid control ECU 3. Combination Meter Assy
COMBINATION METER 711 COMBINATION METER PROBLEM SYMPTOMS TABLE Warning Lights and Buzzer: 7105L01 Symptom Suspect Area See page Check Engine warning light does not light up. 2. ECM 051, 05173 Discharge
More informationReplacement Cluster Fascia Replacement
1 of 12 11/1/2013 9:13 AM SOUL(AM) >2010 > G 2.0 DOHC > Body (Interior and Exterior) Replacement Cluster Fascia Replacement When prying with a flat-tip screwdriver, wrap it with protective tape, and apply
More informationREASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
More informationWait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
More information1. General Description
EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,
More informationINSTRUMENT PANEL ASSEMBLY. INSTRUMENT PANEL ASSEMBLY Component Parts Drawing IP-10 PFP:68200 AIS005BC PIIB0009E
INSTRUMENT PANEL ASSEMBLY Component Parts Drawing PFP:68200 AIS005BC PIIB0009E IP-10 1. Passenger air bag module 2. Front defroster grille (LH) 3. Front defroster grille (RH) 4. Cluster Lid A 5. Instrument
More information2. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal.
Page 1 of 28 Section 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Instrument Panel Removal 1. WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY,
More informationSTEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
More informationTOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
More informationSCION tc Navigation System Preparation. Part Number: PT
Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationModel Year: 2008 Model: xb Doc ID: RM000000SUR00OX. (a) Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: INSTALLATION (2008 x... Page 1 of 10 Last Modified: 2-12-2007 Service Category: Vehicle Exterior 1.6 A Section: Window/Glass Model Year: 2008 Model: xb Doc ID:
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More information1 of 13 5/11/17, 2:59 PM
1 of 13 5/11/17, 2:59 PM REMOVAL WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS, DISABLE THE AIRBAG SYSTEM BEFORE ATTEMPTING ANY STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL COMPONENT DIAGNOSIS OR
More informationINSTRUMENT PANEL ASSEMBLY
2003 Dodge or Ram Truck RAM 1500 Truck 2WD V8-4.7L VIN N Vehicle > Body and Frame > Interior Moulding / Trim > Dashboard / Instrument Panel > Service and Repair > Removal and Replacement INSTRUMENT PANEL
More informationGENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
More informationREMOVAL JS - CHRYSLER L V6 V.V.T Body / Instrument Panel / PANEL, Instrument/Removal
2011 - JS - CHRYSLER 200-3.6L V6 V.V.T. 23 - Body / Instrument Panel / PANEL, Instrument/Removal REMOVAL NOTE: Avenger shown, 200 typical, except where noted. 1. Disconnect and isolate the negative battery
More informationED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal 1. If equipped with power seats, move the seat fully rearward. 2. If equipped with adjustable pedal system,
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
More informationInstrument Panel Assembly Replacement. Fig. 14 Battery Negative Cable Removal/Installation
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Chrysler Truck PT Cruiser L4-2.4L VIN B Conversion
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationPOWER MIRROR CONTROL SYSTEM
RROR POWER RROR CONTROL SYSTEM POWER RROR CONTROL SYSTEM BODY RROR PARTS LOCATION 1 DRIVER SIDE JUNCTION BLOCK - ACC FUSE - AM2 FUSE - ACC-B FUSE OUTER REAR VIEW RROR RH OUTER REAR VIEW RROR LH ACC RELAY
More informationConflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware
More information1 of 6 10/31/2017, 1:57 PM. Fig. 19 Automatic Transmission Shift Knob Removal
1 of 6 10/31/2017, 1:57 PM Fig. 19 Automatic Transmission Shift Knob Removal 2 of 6 10/31/2017, 1:57 PM Fig. 20 Manual Transmission Shift Knob Removal 3 of 6 10/31/2017, 1:57 PM Fig. 21 Removing Accessory
More informationSensor A/C Ambient Temperature 1951
SECTION 412-04: Control Components REMOVAL AND INSTALLATION Sensor A/C Ambient Temperature Removal 1. Remove the radiator upper sight shield. 2. Disconnect the wire harness connector. 3. Remove the A/C
More informationDVD REAR SEAT VIDEO SYSTEM
Read entire instructions thoroughly before starting. TOOLS REQUIRED: DVD REAR SEAT VIDEO SYSTEM MINIVANS WITH ROOF RAILS INSTALLATION INSTRUCTIONS Non-metal trim stick Phillips screwdriver T15, T20, T25
More informationXM Adapter Cable (P/N: ) MUST be used for this vehicle.
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description
More informationTelescopic Lever Detent Clip Replacement
T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained
More informationDISASSEMBLY REASSEMBLY
4 EXTERIOR FRONT BUMPER DISASSEMBLY 1. REMOVE HOOD TO FRONT END PANEL SEAL (a) Using a clip remover, detach the 8 clips and remove the panel seal. 2. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a clip
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationFLOOR SHIFT ASSEMBLY
FLOOR SHIFT ASSEMBLY Components Removal 1. REMOVE THESE PARTS: a. Front door scuff plates b. Cowl side trim c. Lower finish panels d. Lower LH insert e. Lower instrument panel f. Lower RH panel g. Ash
More informationALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Page 1 of 9 Service and Repair FRONT WIPER MOTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM HEAD CAP a. Using a screwdriver wrapped with protective tape, remove
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More information2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6
2003 Dodge or Ram Truck RAM 2500 Truck 4WD L6 5.9L DSL Turbo VIN 6 Vehicle» Body and Frame» Interior Moulding / Trim» Dashboard / Instrument Panel» Service and Repair» Instrument Panel Assembly REMOVAL
More informationSCION xb SIRIUS SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,
More informationOVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
More information2002 Explorer Sport/Sport-Trac Workshop Manual
Page 1 of 18 SECTION 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 2002 Explorer Sport/Sport-Trac Workshop Manual Instrument Panel Removal All vehicles CAUTION: Electronic modules are sensitive
More informationBO 40 MOON ROOF COMPONENTS
BO40 BODY MOON ROOF COMPONENTS BODY BO41 ONVEHICLE INSPECTION INSPECT SLIDING ROOF GLASS ALIGNMENT (a) Start the engine and check the operation time of the sun roof. Operation time: Approx. 8 secs. (b)
More information1. General Description
EXERIOR/INERIOR RIM GENERAL DESCRIPION 1. General Description A: COMPONEN 1. FRON GRILLE EI-00413 Front grille Front grille emblem Clip 2. UNDER COVER EI-00414 Under cover Clip (side) ightening torque:
More informationPRIUS PRIME PRIUS PHV
PRIUS PRIME PRIUS PHV Plug-in Hybrid Gasoline-Electric Hybrid Synergy Drive ZVW52 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Toyota PRIUS PRIME,
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More information1 of 12 8/18/ :52 AM
1 of 12 8/18/2016 11:52 AM REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE a. Discharge fuel system pressure. 2. REMOVE DECK BOARD SUB-ASSEMBLY a. Disengage the 5 clips and turn up the front side of the deck
More informationINTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52A-1 INTERIOR AN SUPPLEMENTAL RESTRAINT SYSTEM (SRS) CONTENTS INTERIOR... 52A SUPPLEMENTAL RESTRAINT SYSTEM (SRS)... 52B 52A-2 INTERIOR CONTENTS SPECIAL TOOL... 3 INSTRUMENT PANEL*... 3 FRONT FLOOR CONSOLE...
More informationSECTION 1A3 - INSTRUMENT PANEL AND CONSOLE
SECTION 1A3 - INSTRUMENT PANEL AND CONSOLE Click on the button for more information. CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). A SRS will consist of either seat
More informationOT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL
More informationINSTRUMENT PANEL WARPAGE REPAIR
PAGE 1 OF 15 AFFECTED VEHICLES: INSTRUMENT PANEL WARPAGE REPAIR ALL 1999-2000 MODEL YEAR CONTOUR AND MYSTIQUE OVERVIEW NOTE! Revisions to the technical instructions are indicated in RED text. This document
More informationMY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo
2013-2014MY F150 CrewCab 1 Tools Required A B C D E F G 4X H I J K 3X L 3X 2X 10X 2X Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 2 Vehicles with selector lever in floor
More informationWhine Noise From Rear of Vehicle
T-SB-003-8 February 6, 208 Service Category Drivetrain Section Axle/Differential Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMION 206-207 Tacoma Body Type(s): D CAB Introduction Some 206
More informationEN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
04 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK, IMPREZA, ASCENT,FORESTER Installation Instruction PART No. H6710AL010 EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 1 2 3 TOOLS NEEDED PRECAUTIONS
More informationPart Number: TAV-713. Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL. Hardware Bag Contents.
Date: 09.04.2013 TOYOTA AVALON 2013 - LED DRL Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad
More informationSide Window Glass Noise During Operation
T-SB-0077-12 May 21, 2012 Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2012 Camry, Camry HV Introduction Some 2012 Camry and Camry
More informationEN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA. Installation Instruction. No. Name Qty Socket ASSY 1 Plug 1 Ring 1 TOOLS NEEDED
02 EN: CIGARETTE LIGHTER KIT LEGACY / OUTBACK IMPREZA PART No. EN: COMPONENTS No. Name Qty Socket ASSY 1 Plug 1 Ring 1 Installation Instruction H6710AL010 1 2 3 TOOLS NEEDED PRECAUTIONS Please refer to
More informationVENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 PRECAUTION... 3 PREPARATION... 5 SYSTEM DESCRIPTION...
VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E PRECAUTION... 3 PRECAUTIONS... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
More informationTOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
More informationVENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 SYSTEM DESCRIPTION... 3 PRECAUTION... 6 PREPARATION...
VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E SYSTEM DESCRIPTION... 3 AUTOMATIC AIR CONDITIONER SYSTEM... 3 WITH COLOR DISPLAY...3 WITH COLOR DISPLAY : Switches
More informationCenter Console Wood Grain Panel Cracked
L-SB-0040- July 3, 20 Service Category Vehicle Interior Section Interior Panels/Trim Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 20 LS460, LS600H Introduction Some 2007-20 model
More informationToyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52070 to complete the installation
More informationFRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
More information2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
More informationTECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
More information75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
More informationSEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
More informationASX / OUTLANDER SPORT / RVR REAR VIEW CAMERA MZ380552EX INSTALLATION AND HANDLING INSTRUCTIONS
ASX / OUTLANDER SPORT / RVR REAR VIEW CAMERA MZ380552EX INSTALLATION AND HANDLING INSTRUCTIONS Navigation (MMCS) unit Camera Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use
More informationfile://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...
Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:
More informationConflicts. TOYOTA 4Runner REARSIGHT. Part Number: Code: MC90 KIT CONTENTS ADDITIONAL ITEMS REQUIRED FOR INSTALL RECOMMENDED TOOLS
TOYOTA 4Runner 2010 - REARSIGHT Part Number: 00016-00085 Code: MC90 Conflicts KIT CONTENTS ITEM QTY DESCRIPTION 1 1 MIRROR/MONITOR 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA EXTENSION HARNESS 4 1 SACK PARTS 5
More informationHeadlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
More information1988 Chrysler LEBARON
1988 Chrysler LEBARON Submodel: Engine Type: L4 Liters: 2.5 Fuel Delivery: FI Fuel: GAS CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze,
More informationELECTRIC VEHICLE DISMANTLING MANUAL
iq EV Electric Vehicle ELECTRIC VEHICLE DISMANTLING MANUAL KPJ10 Series Foreword This guide was developed to educate and assist dismantlers in the safe handling of Scion/Toyota iq EV electric vehicles.
More informationSide Door Sill Trim Plate Package Installation
Page 1 of 5 2014 Chevrolet Equinox Equinox, Terrain VIN L Accessory Installation Manual Accessories Interior Accessories Accessories Document ID: 3619390 Side Door Sill Trim Plate Package Installation
More informationVENTILATION SYSTEM SECTION VTL CONTENTS VENTILATION, HEATER & AIR CONDITIONER VTL-1 FUNCTION DIAGNOSIS... 3 PRECAUTION... 6 PREPARATION...
VENTILATION, HEATER & AIR CONDITIONER SECTION VTL A VENTILATION SYSTEM B C D CONTENTS E FUNCTION DIAGNOSIS... 3 AUTOMATIC AIR CONDITIONER SYSTEM... 3 WITH COLOR DISPLAY...3 WITH COLOR DISPLAY : Switches
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationDash Board / Instrument Panel: Service and Repair
1995 Chevy Truck C 1500 P/U 2WD V8-350 5.7L VIN K TBI Copyright 2008, ALLDATA 9.90 Page 1 Dash Board / Instrument Panel: Service and Repair INSTRUMENT PANEL ASSEMBLY REPLACEMENT Remove or Disconnect 1.
More informationREMOVAL WJ INSTRUMENT PANEL SYSTEM INSTRUMENT PANEL SYSTEM (Continued)
WJ INSTRUMENT PANEL SYSTEM 23-127 entire structural duct unit must be replaced. Most other trim and functional components of the instrument panel are available for service replacement separately from the
More information2002 Jeep Grand Cherokee Limited
Remove the two nuts that secure the instrument panel wire harness ground eyelets to the studs on the floor panel transmission tunnel in front of and behind the ACM. Disengage the retainers that secure
More informationSCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
More informationTechnical Service BULLETIN
Technical Service BULLETIN March 9, 004 Title: Models: 03 04 4Runner BO005-04 BODY TSB REVISION NOTICE: April 8, 004: A note has been added to step 4 on page 3 to clarify the removal of the roof rack.
More informationRear Door: Service and Repair REAR DOOR
2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY
More informationSplicing Procedures 4. 2 Insert the new wire between the parted strands. If more than one wire is being spliced, wrap them in opposite directions. Use
Splicing Procedures 1 Splicing Procedures Refer to applicable wiring diagrams for circuit information. This procedure contains multiple splicing techniques. Review splicing procedures prior to performing
More informationPage 1 of 33 SPECIFICATIONS 2013 Ford Edge 3.5L Eng Limited Print Date: TORQUE SPECIFICATIONS Description Nm lb-ft lb-in Assist handle bolts 9-80 B-pillar upper trim panel screw 9-80 C-pillar trim panel
More information