INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE

Size: px

Start display at page:

Download "INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE"

Doris Harmon
5 years ago
Views:

Page 1 of 18 2016 Dodge Grand Caravan 3.

1 Page 1 of Dodge Grand Caravan 3.6L Eng VIN G SE Service Manual: BODY - INTERIOR & EXTERIOR Print Date: INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE Fig 1: Base Floor Console Components 1. Remove the front plug (2) and clip (3). 2. Slide the console (1) forward while lifting slightly (4) to clear the rear load floor hook. 3. Remove the console (1). INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > PREMIUM FLOOR CONSOLE

2 Page 2 of 18 Fig 1: Premium Floor Console Components 1. Pull up on the bottom release handle (3) in the front (2) of the console (1). 2. Lift the rear of the console (4) up several inches. 3. Pull rearward to disengage from floor and remove console (1). INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > FULL FLOOR CONSOLE

3 Page 3 of 18 Fig 1: Full Floor Console Components 1. Position both the front seats to full forward positions. 2. Remove the fastener (3) securing the floor console to the floor pan bracket (5). Repeat on the opposite side. 3. Position both the front seats to the full rear positions.

4 Page 4 of Remove the fastener (4) securing the floor console to the floorpan bracket (4). Repeat on the opposite side. 5. Disconnect the negative battery cable. Fig 2: Upper Console Bezel 6. Using (special tool #C-4755, Trim Stick), pry around the perimeter of the upper console bezel (1) to disengage the retaining clips. 7. Position the upper console bezel (1) rearward. Do not remove the bezel at this time.

5 Page 5 of 18 Fig 3: Upper Console Bezel & Wiring Harnesses 8. Rotate the upper console bezel (1) and disconnect the wiring harnesses (2). 9. Remove the upper console bezel (1).

6 Page 6 of 18 Fig 4: Full Floor Console Components 10. Remove the two fasteners (2) securing the floor console (1) to the instrument panel. 11. Remove the pushpin fasteners (6) securing the floor console (1) to the instrument panel. Repeat on the opposite side. 12. Pull rearward to disengage and remove the floor console (1).

7 Page 7 of 18 Fig 5: Full Floor Console 13. Lift the rear portion of the floor console upward between the front seats. 14. Lift the entire floor console upward. 15. Remove the floor console from the vehicle through the passenger side door opening. INTERIOR > CONSOLE, FLOOR > INSTALLATION > INSTALLATION > BASE FLOOR CONSOLE

8 Page 8 of 18 Fig 1: Base Floor Console Components 1. Position the console (1) at a slight angle [front (4) slightly higher than the rear]. 2. Slide the console (1) rearward into the underneath the Stow N Go second row seat door assembly frame. 3. Align the console until the anchor plug hole is centered on the winch hole. 4. Reinstall the clip (3) first and then while pushing downward on the console with slight pressure, reinstall the cover plug (2). INTERIOR > CONSOLE, FLOOR > INSTALLATION > INSTALLATION > PREMIUM FLOOR CONSOLE

Page 9 of 18 Fig 1: Premium Floor Console Components 1. Position the console (1) at a slight angle [rear (4) slightly higher than the front]. 2. Slide the console forward into the floor bracket (3).

9 Page 9 of 18 Fig 1: Premium Floor Console Components 1. Position the console (1) at a slight angle [rear (4) slightly higher than the front]. 2. Slide the console forward into the floor bracket (3). 3. Rotate the rear of the console down (4) until it is resting on the floor bracket (3). 4. Push down on the rear of the console (4) until it is seated in the rear floor bracket. INTERIOR > CONSOLE, FLOOR > INSTALLATION > INSTALLATION > FULL FLOOR CONSOLE

10 Page 10 of 18 Fig 1: Full Floor Console NOTE: Front seats are to be in full rearward position as described in the removal procedure.

11 Page 11 of Position the floor console through the passenger side door. 2. Insert the front portion of the floor console downward, between the front seats. 3. Rotate the rear portion of the floor console downward, between the front seats. Fig 2: Full Floor Console Components 4. Route the console bezel wiring harness through the top of the floor console. 5. Align and position the floor console (1) to the floorpan bracket (5) and dash. 6. Install the fastener (4) securing the floor console to the floor pan bracket (5). Tighten the fasteners to 10 N-m (89 in-lbs.). Repeat on the opposite side.

Page 12 of 18 7. Install the two fasteners (2) securing the floor console (1) to the instrument panel. Tighten the fasteners securely. 8.

12 Page 12 of Install the two fasteners (2) securing the floor console (1) to the instrument panel. Tighten the fasteners securely. 8. Install the pushpin fastener (6) securing the floor console (1) to the instrument panel. Repeat on the opposite side. Fig 3: Upper Console Bezel & Wiring Harnesses 9. Rotate the upper console bezel (1) and connect the wiring harnesses (2).

13 Page 13 of 18 Fig 4: Upper Console Bezel 10. Align and position the upper console bezel (1) to the floor console and the instrument panel. 11. Hand tap around the perimeter of the upper console bezel (1) to engage the retaining clips. 12. Connect the negative battery cable.

14 Page 14 of 18 Fig 5: Full Floor Console Components 13. Position both front seats to the full forward position. 14. Install the fastener (3) securing the floor console to the floor pan bracket (5). Tighten the fasteners to 10 N-m (89 in-lbs.). Repeat on the opposite side. INTERIOR > CONSOLE, FLOOR, BASE > REMOVAL > REMOVAL > FLOOR CONSOLE BRACKET

15 Page 15 of 18 Fig 1: Floor Console Bracket, Screws & Electrical Connector 1. Remove the floor console. Refer to CONSOLE, FLOOR, REMOVAL. 2. Remove the floor console tray on premium consoles (if equipped). 3. Remove the four screws (2) to the floor console bracket (3). 4. Lift the base bracket out of the carpet opening. 5. Disconnect the electrical connector (1) from the bracket (if equipped with premium console). INTERIOR > CONSOLE, FLOOR, BASE > REMOVAL > REMOVAL > FLOOR CONSOLE TRAY

16 Page 16 of 18 Fig 1: Floor Console Tray, Bracket & Screws 1. Remove the floor console. Refer to CONSOLE, FLOOR, REMOVAL. 2. Remove the four screws (2) holding the console tray ()1 to the console bracket (3). INTERIOR > CONSOLE, FLOOR, BASE > INSTALLATION > INSTALLATION > FLOOR CONSOLE BRACKET

Page 17 of 18 Fig 1: Floor Console Bracket, Screws & Electrical Connector 1. Connect the electrical connector (1) to the bracket (if equipped with premium console). 2.

17 Page 17 of 18 Fig 1: Floor Console Bracket, Screws & Electrical Connector 1. Connect the electrical connector (1) to the bracket (if equipped with premium console). 2. Place the base bracket into position in the carpet opening. 3. Install the four screws (2) to the floor console bracket (3). 4. Install the floor console tray on premium consoles (if equipped). 5. Install the floor console. Refer to CONSOLE, FLOOR, INSTALLATION. INTERIOR > CONSOLE, FLOOR, BASE > INSTALLATION > INSTALLATION > FLOOR CONSOLE TRAY

18 Page 18 of 18 Fig 1: Floor Console Tray, Bracket & Screws 1. Install the four screws (2) holding the console tray ()1 to the console bracket (3). 2. Remove the floor console. Refer to CONSOLE, FLOOR, INSTALLATION.

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION HEATED SEAT MODULE (HSM), MEMORY SEAT MODULE (MSM) OR MEMORY HEATED SEAT MODULE (MHSM) NOTE: After installation, initialize memory seat module. Move each power seat adjuster motor,