LDXRTB Series Random Top and Bottom Drive Semi Automatic Case Sealer

Transcription

1 Little David Case Sealer LDXRTB Series Random Top and Bottom Drive Semi Automatic Case Sealer Revision E Operator s Manual

2 LITTLE DAVID CASE SEALER LDXRTB Operation Copyright Loveshaw Loveshaw, Inc. 0 Easton Turnpike, PO. Box South Canaan, PA Tel: 00 0 Fax: 00 ITW PADLOCKER, LTD. Unit Brunel Gate West Portway Industrial Estate Andover, Hampshire SP0 SL ENGLAND Tel: Fax: Friday, February, 00 i

3 Table of Contents Chapter : Introduction Chapter : Operating Safety Chapter : Overview Chapter : Installation Chapter : Theory of Operation 0 Chapter : Machine Components Chapter : Maintenance

4 Chapter : Troubleshooting Chapter : Warranty 0 Chapter 0: Assembly Drawings and Schematic ii

5 Chapter Introduction T hank you for purchasing the Little David case sealer, the LDXRTB. The LDXRTB is semiautomatic top and bottom drive case sealer. The LDXRTB is a robust built / case sealer constructed of quality materials, linear bearing, pneumatic and electrical components.. All employees who will be required to operate and maintain the case sealer must read this manual to ensure safe operation as well as proper setup and maintenance throughout the life of the machine. After reading this manual, you will know how to perform the following functions, How to operate the machine safely. How to set the conveyor height of the machine How to set the head height limiter. How to set the machine to operate in uniform mode. How to adjust the head balance regulator. How to adjust the side rail trigger sensor Troubleshooting and replacing of worn or defective parts. Throughout this manual there are several illustrations designed to help you perform the variety of tasks described.

6 Chapter Operating Safety Observe the warnings and cautions below when using the Little David LDXRTB case sealer. Within this manual on page, all safety labels are depicted with location and part number. If a safety, label is missing or not legible it must be replaced immediately. Failure to follow safety labels can lead to injury or damage to the machine. Instruction: Requirement to System Operation Instruction: An electrical receptacle must be located near the machine. The line cord connection to the receptacle is the disconnect means for the machine. The receptacle must be located in an area that is easily accessible to all personnel. Warning: Potential Bodily Injury Warning: Always disconnect all sources of energy to the machine before performing maintenance. Sources of energy include electrical and pneumatic. Refer to your company s lock out tag out procedures. Warning: Never bypass or remove safety guards from the machine or tape cartridge. Warning: Never override safety devices such as Emergency Stop switches. Warning: Never adjust the machine or tape cartridges when the machine is operating. Warning: Never place hands or body inside confines of the machine unless top head assembly is locked in place and all power sources are locked out. Warning: Never wear jewelry, loose clothing, such as ties, scarves etc and long hair must be pulled back when operating this machine. Warning: Never pull a jammed box out of the machine while it is in operation. Stop machine and raise head with bypass switch. Warning: When feeding a semi automatic case sealer always hold the top flaps down a rear of box, to avoid accidental entrapment in the machine

7 This manual contains operator information for Little David Application Equipment. It is directed toward the person who operates and maintains the machine. Read through the manual completely before operating the machine. Thereafter, refer to it as necessary. Take special note of all warnings, cautions, and maintenance instructions. Like any other piece of equipment, the Little David Case Sealer functions best when maintained and used correctly. Caution: Potential Machine Damage: Caution: Never push or drag machine across the floor with the top head assembly fully raised. Makes sure it is completely lowered. Caution: Never pull the machine by its pack table or side rails. Caution: Provide and use proper electrical power. Caution: Do not operate, maintain, or otherwise use this machine, except as described in this manual. Special instruction: The top drive assembly incorporates adjustable belt guards. The guards are made adjustable to maintain / gap between the top of the belt and the guard itself. This eliminates a pinch point between the guard and the belt. The guards are located at the rear of the machine where the belt wraps around the drive pulleys. The guards must be adjusted inward as the belts wear. It is mandatory the gap be adjusted to no more than / clearance between the top of the belt and the guard itself. The guard is simply adjusted by loosening two mm panel head machine screws and sliding the guard inward to maintain the / gap. Failure to adjust the guards may cause injury. Mounting screws Gap not to exceed / Drive belt Belt guard

8

9 Chapter Case Sealer Sections Overview This manual covers several parts of the machine. The following diagram identifies the key sections of the machine. Head Lock Mast Assy. Top Drive Head Assy. Estop (head) Bottom Drive Sensing Paddle. Frame Assy. Side Rails Pack Table Air Regulators Side Rail Lock Control Station

10 Machine Specifications Machine dimensions: Height: conveyor height Length including pack table: ¼ overall pack table 0 ¼ overall 0 pack table 0 ¼ overall 0 pack table ¼ overall pack table Width: / Conveyor height: to ¾ Standard Electrical Requirements: Standard Voltage: 0//0 with amp dedicated service. Optional voltages are available consult factory.

11 Operating speed: Standard belt speed: ft/min Optional high belt speed: ft/min Air Requirement: 0 psi maximum throughput based on maximum box range. Machine box capacity: Length: to infinite Width: ½ to ½ Height: ½ to Low box option of ½ tall, tape tab length will be reduced by ½.

12 Chapter Installation A lways check for any signs that the machine may have been damaged before fully removing it from the shipping skid. If machine arrives damaged contact Loveshaw immediately to help in filing a claim with shipping company. Section : Placing the Machine The case sealer is fully assembled and ready for operation. Step One: Carefully remove the machine from the shipping skid. Remove all fasteners and brackets holding the machine to the skid. Remove head assembly shipping brackets. Step Two: Take care removing the machine from the skid as it weighs 0 pounds! Use a forklift or similar device to complete this task Step Three: Move machine to designate location. It may be necessary to adjust the conveyor height of the machine. The legs on the machine are adjustable by loosening the leg clamping hardware and sliding the leg to its proper position. The use of a jack or forklift is required. (Refer to figure on page ) machine. Step Four: Connect compressed air and electricity to the

13 mm wrench Outer leg Inner leg Leg retracted Leg extended

14 Chapter Theory of Operation LDXRTB The LDXRTB will automatically adjust itself for the width and height of the box to be sealed. With the machine started, a box is placed on the infeed pack table. The box is moved forward until photoelectric sensor PE is triggered. The triggering of PE will energize solenoid valve SV which will cause the side rails to travel inward centering the box on the pack table and holding it in place. The operator is able to fill the box with product and fold the top flaps of the box down. While holding the top flaps down the operator pushes the box forward until the leading panel of the box contacts the sensing paddle. When the sensing paddle is depress it contacts an air limit switch which in turns supplies pilot air pressure to solenoid valve V. When valve V is energized, the top head assembly will begin to travel upward until the front sensing paddle is no longer being held in by the front panel of the box. Now the operator can push the box into the machine under the top drive assembly. (Note: always hold the top flaps of the box down at the rear of the box to avoid accidental entrapment with the top drive assembly) The top drive assembly will lower down on top of the box and will propel it through the machine. As the box moves off photoelectric sensor PE the side rail solenoid valve, SV will deenergize and the side rails will open to their home position. The box will travel through the tape cartridges and tape will be applied to the box. The box will exit the machine and the top head assembly will lower down to its home position. 0

15 Key design features: The LDXRTB incorporates an adjustable bracket for photoelectric sensor PE. The bracket allows various positions to trigger the side rails inward. By mounting the bracket closer to the infeed of the machine, the side rails will close on to a greater amount of the side panels of the box. This position is optimal if the operator is loading product into the box before sealing it. By mounting the photoelectric sensor at the beginning of the pack table the side rails will close in sooner as the box is moved toward the infeed of the machine. This position is optimal if the box is already filled and the flaps are folded. The operator can advance the box and the side rails will center it, as the box is moving. The LDXRTB incorporates a box overstuffed switch. This switch is located on the bottom side of the top head assembly. As a box is fed into the machine, the top head drive assembly lowers down on top of it. The overstuff switch is depressed in ward. This action eliminates any chances of the sensing paddle retriggering causing the head to rise while the box is being processed. Typically, an overstuffed box can retrigger the sensing paddle and the head will raise causing poor tape application or a box jam. The overstuff switch nulls out the sensing paddle while it is activated. The LDXRTB incorporates an adjustable top head assembly limiter. The head limiter controls the minimum height of the top head assembly at rest. (The starting point) The head limiter allows for more through put speed by limiting how far the top head assembly travels before it clears the height of the box to be processed. For example if the minimum box height to be processed is 0 inches, the head limiter can be set at.. By setting the limiter, the head only travel downward to the. position after each box. The LDXRTB incorporates a movable control station. The control station can be placed to any metal surface of the machine.

16 This versatility allows the operator to place the controls of the machine at the best position for them The LDXRTB incorporates uniform lock capability on the head and side rails assembly on the machine. The top head and side rail assemblies can be locked at a specific position to process a batch of same size boxes. The assemblies can be locked in either tandem or individually dependant on need. This increases the throughput of the machine since it does not have to wait for the machine to adjust to the box. The LDXRTB incorporates a maintained manual head raising toggle switch. This switch allows the head to be raised without the machine running. With the machine stopped and the emergency stop switches extended, the head can be raised. This is convenient when refilling the bottom tape cartridge or box jam clearing. (Note: never enter under the machines top head assembly, without locking the upper head assembly with the lock knob.) Optional feature: The LDXRTB can be fitted with the high speed option to increase throughput. The option consists of increased belt speed from ft/ min to ft/min. and a head raise dampening circuit. The head raise dampening circuit limits the amount of over travel the top head assembly will experience as it senses the height of the box. The top head assembly travels upward as the sensing paddle is depressed. As it raises it is building up speed. Even when the sensing paddle is released, the head will continue to travel upward until its momentum ends. The dampening circuit is triggered when the sensing paddle is released and the cylinder exhaust blocking valves are closed for a short period to counter act the upward momentum of the top head assembly.

17 Machine Components Chapter Control Station The control station consist of an electrical enclosure, push pull mushroom head emergency stop switch and a momentary start pushbutton. The control station has two magnets on the back side of it which allows the operator to locate the machine controls to best fit their position at the machine. ESTOP START

18 Pneumatic regulators The regulators optimize the machine for the customers specific needs. Regulators R and R control the top head lifting movement while R controls the side rails. Regulator R controls the head lifting pressure and is normally set to 0 psi. Lowering the air pressure will make the top head assembly move upward sluggishly. Increasing the pressure will make the head travel upwards quickly. However; by increasing the pressure the head over travel will increase and actually decrease through put. Regulator R controls the downward force the top head assembly will exert on to the top of the box when it contacts it. By decreasing the pressure, the head will have more downward force on the box, which is desirable for overfilled conditions. Increasing the pressure will lessen the top head assembly downward force, which is desirable for voided boxes. Note: too much pressure may inhibit the top assembly from lowering downward or may cause box staling due to the top belts from not contacting the box with enough drive. Regulator R controls the pressure that the side rails center and hold the box. By increasing the pressure the side rails can center heavier boxes on the pack table. By increasing the pressure the side rails have more clamping force which makes it more difficult to advance a box into the machine. Lowering the pressure is desirable when processing light boxes. Be careful not to lower the pressure too much, this will cause the side rails not to fully travel inward. R R R

19 Top drive assembly The top drive assembly consist of a / hp gear motor, sprockets, chain and endless, guided, rough top belting. The top drive assembly, assist in conveying the box forward through the machine. The top drive assembly insures that tall unstable boxes will not topple over as they process through the machine. The endless rough top belt has an integral guide rib on the back of it. This guide eliminates any sophisticated apparatus to track the belt. The endless belt feature has increased longevity over conventional laced belting. MOTOR ESTOP DRIVE BELT

20 Bottom drive assembly The bottom drive assembly consist of a / hp gear motor, sprockets, chain and endless, guided, rough top belting. The bottom drive assembly is the main driver in conveying the box forward through the machine. The bottom drive assembly insures that boxes will travel through the machine without stalling The endless rough top belt has an integral guide rib on the back of it. This guide eliminates any sophisticated apparatus to track the belt. The endless belt feature has increased longevity over conventional laced belting. DRIVE BELT DRIVE MOTOR

21 Sensing paddle assembly The sensing paddle assembly, consist of two air switches and a single electric limit switch. The sensing paddle primary function is to measure the height of the box as it at the infeed of the machine. When the sensing paddle is depressed inward by the leading panel of the box, air switch AS opens and air flows to valve V. V in turn fills the head lifting cylinders which causes the top head assembly to travel upward. When the top head assembly raises higher than the box to be processed, air switch AS releases and the head will start to travel downward on top of the box to be processed. The second air limit switch AS works in conjunction with AS to eliminate any false head raise triggering. When a box is travelling under the top head assembly into the machine, it is passing under the headsensing paddle. If the top of the box inadvertently contacts the sensing paddle without AS the head would raise up again and cause taping or jamming issues in the machine. Air limit switch AS nulls out air switch AS when it is triggered. AS is located under the top drive assembly at the infeed of the machine just behind the sensing paddle. Air switch AS is the manual head raise switch. The electrical limit switch LS is an optional device, which is part of the highspeed option. The function of LS is to signal when the front panel of the box releases the sensing paddle. The electrical signal is fed to a one shot logic module with time delay. The logic module turns off the head lifting cylinders exhaust blocking valves. This reduces the amount of over shoot that the top head assembly would normally travel. By stopping the top head assembly up momentum abruptly the machines box cycle time is reduced.

22 AS LS AS AS Electrical enclosure assembly The electrical enclosure assembly is located inside the frame of the machine behind side panel. The enclosure is located next to the air pressure regulator. Inside the electrical enclosure are fuses, contactors, overload relays and terminal blocks. The devices selected protect the machine from short circuit and overload conditions.

23 ELECTRICAL ENCLOSURE Pack table assembly The pack table assembly consists of conveyor rollers, photoelectric sensor and works in conjunction with the side rails. The pack table design allows it to be used as a platform to fill a box on and then be able to convey it to the infeed of the machine. The photoelectric sensor PE is mounted under the pack table with is sensing area pointed up through the rollers of the table. The photoelectric sensor is triggered when the box is rolled over the top of it. The side rails will travel inward and center and hold the box in place. With the box being held in position an operator can fill it without the box moving around. When the box is filled the top flaps must be folded down and pushed up against the sensing paddle. Once the box enters the machine the photoelectric sensor will be cleared and the side rails

24 will open completely. The position of the sensor can be changed to allow the side rails to be triggered either earlier or later. SIDE RAILS PE CONVEYOR ROLLERS ADJUSTABLE BRACKET 0

25 Chapter Maintenance Safety: NEVER perform any maintenance on the LDXRTB without first following your company s LOCK OUT / TAG OUT procedures. Replacing Top Drive Gear motor. Disconnect motor cable from the motor conduit box.. Remove top drive guard. (guard with integral manual head raise switch). Loosen two set screws which hold sprocket on motor shaft. (measure distance from face of sprocket to end of motor shaft and record). Loosen four mounting screws which secure motor to mounting bracket.. Slide motor to release drive chain tension.. Slide sprocket off of motor shaft.. Remove motor mounting screws completely and remove motor.. Mount replacement motor on to mounting bracket and replace the four mounting screws.. Slide sprocket on to motor shaft with the drive chain on the sprocket. Position sprocket on the motor shaft as recorded in step. Tighten sprocket set screws when proper position is obtained.

26 0. Slide motors until drive chain is tensioned properly and tighten the four mounting screws. The drive chain should have approximately ½ inch deflection when pressed. Over tightening the chain can cause premature wear.. Replace top drive guard.. Reconnect motor cable in the motor conduit box. MOTOR SPRCKET TOP DRIVE MOTOR BELT COVER MOTOR MOUNTING SCREWS

27 Replacing Bottom Drive Gear motor. Disconnect motor cable from the motor conduit box.. Remove bottom drive top, side and rear guards from the machine.. Remove guard form bottom drive motor drive guard.. Disconnect motor cable from the motor conduit box.. Loosen two set screws which hold sprocket on motor shaft. (measure distance from face of sprocket to end of motor shaft and record). Loosen four mounting screws which secure motor to mounting bracket.. Slide motor to release drive chain tension.. Slide sprocket off of motor shaft.. Remove motor mounting screws completely and remove motor. 0. Mount replacement motor on to mounting bracket and replace the four mounting screws.. Slide sprocket on to motor shaft with the drive chain on the sprocket. Position sprocket on the motor shaft as recorded in step. Tighten sprocket set screws when proper position is obtained.. Slide motors until drive chain is tensioned properly and tighten the four mounting screws. The drive chain should have approximately ½ inch deflection when pressed. Over tightening the chain can cause premature wear.. Replace all guards removed in earlier steps.. Reconnect motor cable in the motor conduit box.

28 MOTOR SPROCKET MOTOR MOUNTING SCREWS

29 BOTTOM DRIVE BELTS BOTTOM DRIVE MOTOR Replacing Top Drive Belt. Remove top drive belt covers.. Relieve belt tensioning spring.. Slide belt over pulleys to get center guide of belt out of the center grooves of the pulleys.. Install new belt by first putting belt over one of the pulleys and then sliding it over the other pulley while pulling the belt.

30 . Retension spring until it is fully compressed.. Replace top drive belt cover. DRIVE BELT TENSIONER TOP DRIVE BELTS

31 Replacing Bottom Drive Belt. Remove bottom drive belt covers.. Relieve belt tensioning spring.. Slide belt over pulleys to get center guide of belt out of the center grooves of the pulleys.. Install new belt by first putting belt over one of the pulleys and then sliding it over the other pulley while pulling the belt.. Retension spring until it is fully compressed.. Replace top drive belt cover. BOTTOM DRIVE BELTS DRIVE BELT TENSIONER

32 Chapter Troubleshooting: PROBLEM CAUSE CORRECTIVE ACTION Machine will not start. Box jamming in machine. Top head assy. won t move. Side rails will not move. Emergency stop switch(s) activated either control box or top head assembly. No incoming power. Defective start pushbutton Box is out of range of machine. Box is voided and head is crushing it. Tape cartridge problems. Drive belting worn. Machine Estopped. Air not present at machine. Air switch AS is not working. Air switch AS is not working. Head lift cylinders blocking valve failure. Machine Estopped. Side rail lock knob engaged. Photo eye PE is not working. Solenoid SV is not working. Check that both Estop switches are not engaged. Check machine fuses and plant receptacle. Replace pushbutton. Do not run out of spec box. Adjust head balance regulator. Check tape cartridge troubleshooting. Replace drive belts. Check that Estops are not engaged. Connect machine airline. Replace air switch. Replace air switch. Replace blocking valves. Check that Estops are not engaged. Release side rail lock knob. Replace photo eye. Replace solenoid valve.

33 Drive belts are slipping. Belts are not tensioned. Belts are worn. Adjust tensioner until spring is collapsed. Replace drive belts.

34 Chapter Warranty: CASE SEALER, CUSTOM & SPECIAL APPLICATIONS Little David Warranty For: All Standard Little David SemiAutomatic Case Sealers. All Standard LD Series Fully Automatic Case Sealers. All Special Application Case Sealers (Fully & Semi Automatic). YEAR WARRANTY ON DRIVE MOTOR YEAR WARRANTY ON GEAR MOTOR YEAR WARRANTY ON GEAR REDUCER YEAR WARRANTY ON TAPE CARTRIDGE (EXCEPT FOR MOVING PARTS THAT ARE SUBJECT TO NORMAL WEAR, TEAR AND REPLACEMENT WHICH ARE WARRANTED ONLY TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP.) YEAR ON PLC YEAR ON SERVO DRIVE YEAR ALL OTHER PARTS Except for wear and moving parts. *LIMITED WARRANTY LOVESHAW, an ITW COMPANY (HEREIN AFTER LOVESHAW ) WARRANTS ONLY THAT THE GOODS SOLD BY IT SHALL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP, UNDER PROPER AND NORMAL USE AND MAINTENANCE, AS FOLLOWS: DRIVE MOTOR YEARS GEAR REDUCER YEARS GEAR MOTOR YEARS (THIS APPLIES TO SIDE BELTS ONLY) TAPE CARTRIDGE YEARS (EXCEPT FOR MOVING PARTS AND PARTS WHICH ARE SUBJECT TO NORMAL WEAR, TEAR AND REPLACEMENT WHICH ARE WARRANTED ONLY TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP); PLC YEAR SERVO DRIVE YEAR ALL OTHER PARTS YEAR (EXCEPT FOR MOVING PARTS AND PARTS, WHICH ARE SUBJECT TO NORMAL WEAR, TEAR AND REPLACEMENT WHICH ARE WARRANTED ONLY TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP). 0

35 THE WARRANTY PERIOD SHALL COMMENCE AS OF THE DATE OF DELIVERY TO THE PURCHASER. THE OBLIGATION OF LOVESHAW UNDER THIS WARRANTY IS STRICTLY LIMITED TO THE COST OF REPAIRING OR REPLACING, AS LOVESHAW MAY ELECT, ANY PART OR PARTS THAT PROVE IN LOVESHAW S JUDGMENT TO HAVE BEEN DEFECTIVE IN MATERIAL OR WORKMANSHIP AT THE TIME THE GOODS WERE SHIPPED FROM LOVESHAW S PLANT. ANY WARRANTY CLAIM NOT MADE IN WRITING TO LOVESHAW AT ITS HOME OFFICE WITHIN THE APPLICABLE WARRANTY PERIOD AND WITHIN 0 DAYS OF FAILURE WILL NOT BE VALID. THIS IS THE SOLE AND EXCLUSIVE REMEDY AVAILABLE UNDER THIS WARRANTY. UNDER NO CIRCUMSTANCES WILL LOVESHAW BE LIABLE FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES. IF REQUESTED BY LOVESHAW, PURCHASER SHALL RETURN ANY DEFECTIVE PART OR PARTS TO LOVESHAW S PLANT, FREIGHT PREPAID. ALL WARRANTY PART REPLACEMENT AND REPAIRS MUST BE MADE BY LOVESHAW OR A LOVESHAW DEALER AUTHORIZED TO HANDLE THE GOODS COVERED BY THIS WARRANTY. ANY OUTSIDE WORK OR ALTERATIONS DONE WITHOUT LOVESHAW S PRIOR WRITTEN APPROVAL WILL RENDER THIS WARRANTY VOID. LOVESHAW an ITW COMPANY WILL NOT ASSUME ANY EXPENSE OR LIABILITY FOR ANY REPAIRS MADE TO ITS GOODS OUTSIDE ITS WORKS WITHOUT ITS PRIOR WRITTEN CONSENT. THIS WARRANTY SHALL NOT APPLY TO ANY ITEM THAT HAS NOT BEEN USED, OPERATED, AND MAINTAINED IN ACCORDANCE WITH LOVESHAW S RECOMMENDED PROCEDURES. LOVESHAW SHALL HAVE NO LIABILITY WHATSOEVER WHERE THE GOODS HAVE BEEN ALTERED, MISUSED, ABUSED OR INVOLVED IN AN ACCIDENT. NO PERSON IS AUTHORIZED TO MAKE ANY WARRANTY OR TO CREATE ANY LIABILITY BINDING UPON LOVESHAW, WHICH IS NOT STATED IN THIS WARRANTY. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, WHICH ARE HEREBY EXCLUDED. IN PARTICULAR, THE IMPLIED WARRANTY OF MERCHANTABILITY, AS WELL AS THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED. LOVESHAW an ITW Company 0 Easton Turnpike, South Canaan,, PA FAX 0..

36 Chapter 0 ASSEMBLY DRAWINGS AND SCHEMATICS

37 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS. /.0 B B. /. TOP DRIVE EXTENSION.0 /.0 BASE MACHINE w/ PACK TABLE A A 0.0 /. 0.0 /..0 /. CONVEYOR OPENING REQUIRED BASE MACHINE w/ OPTIONAL PACK TABLES.00 /.0 to. / 0. Conv. Height MAT'L PART # CAD FILE. / Conv. Height LDXRTB MAIN ASSY.idw NOTE: TOLERANCES UNLESS OTHERWISE NOTED: FRACTIONS + / Belt Speed: ft/min (Standard) ft/min (Optional) Air Reqired: 0 psi Power Required: VAC Box Range: L =.0 /. min to INF. W =. /. min to. /. max H =. /. min to.0 / 0. max *(. /. min height with smaller tape leg) LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. NOTED STD PLOT DATE //00.X = +.00 ST. ST. TITLE N/A DRAWN DATE //00 INCH.XX = +.0 ANGLES + /.XXX = +.00 STAINLESS : NO FINISH DO NOT SCALE PRINT LDXRTB FOOTPRINT THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY.X = +.0mm METRIC.XX = +.mm MACH. FINISH DWG NO LDXRTB MAIN ASSY SCALE N/A INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER.XXX = +.mm MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. DRAWN tonys APPROVED TONYS

38

39 Parts List FINISH REVISION HISTORY ITEM QTY PART NUMBER DESCRIPTION REV DESCRIPTION DATE APPROVED N00 ELBOW, / NPT X / A RELEASED //00 TONYS B ECO 00 //00 TONYS TUBE H0B PLUG, HEX, / NPT N LOCK OUT VALVE, / 0 HEAD LIFTING VALVE NPT 0 V D NMBA MOUNTING BRACKET D PF0 BRASS STREET ELBOW, 0, / NPT 0 AIR DUMP VALVE N REG. PRECISION MOD. SV N0 REGULATOR, GAUGE SEE NOTE HANDLE SIDE RAIL VALVE PF ELBOW, /NPT X / SV PUSHLOC PSR FITTING 0 N000 coupling / npt N000 ELBOW 0 DEG FEM HC NIPPLE PF PF PLUG, HEX SOC PIPE, / NPT N00 MUFFLER, / NPT n fitting / npt / tube N00 QUICK EXAUST C PF0 TEE, / NPT X / PUSHLOC C FFHMG00P0 FHCS Mx0 0 LDX00 PLATE, PNEU. ASSY. FSHMG0P0 SHCS Mx LG. SEE NOTE FLWMGP LOCK WASHER M HEAD LOCKING VALVE N REGULATOR, GAUGE SV HANDLE HEAD LIFTING / MAIN REGULATOR ( Only for high speed opt. ) N00 FITTING M to / R TUBE PF QUICK DISCONNECT PLUG, / MNPT N GAUGE 0 to 0 psi N0 valve, blocking SIDE RAIL REGULATOR N TA THREAD ADAPTER R N AIR FILTER w/ BRKT 0 N0 VALVE / AIR PILOT N0 VALVE SOL / 0vac N0 VALVE SOL / vac B N VALVE CABEL 0 vac B N/ VALVE CABEL vac 0 N00 CONNECTOR, HEAD BALANCE REG. STRAIGHT, / NPT X R / TUBE N00 FITTING / TO / NPT FNLNMFS M NYLON LOCKING NUT S.S. FFWMFP FLAT WASHER M FHHMF00 HHCS M X 0 FPHSB00P0 SCREW x " LG FLWSBP # LOCK WASHER FHFNSBP # HEX NUT NOTE:. PNEU. SCHEMATIC # PNEU0 (G) H ELBOW. CHECK VALVE VOLTAGE BEFORE ORDERING. PF PIPE ADAPTER, / X / LDX0 MUFFLER, FOAM CPJ000 CABEL TIE A MAT'L PNEU LDXRTB rev TOLERANCES B.IDW UNLESS LOVESHAW an ITW Company A PART # CAD FILE PLOT DATE OTHERWISE NOTED: Mar 00 :00AM RT., SOUTH CANAAN, PA. NOTED STD DRAWN DATE N/A //00 DO NOT SCALE PRINT STAINLESS : NO FINISH.PNEU/LDXRTB/M.X = +.00 TITLE ST. ST..XX = +.0 ANGLES / + INCH +.XXX =.00.X + =.0mm MACH. PNEU LDXRTB rev B N/A THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC.XX = +.mm LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY.XXX + =.mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE MATERIAL CHECKED REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER FRACTIONS + / TONYS WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. tonys DRAWN APPROVED

40 Parts List REVISION HISTORY ITEM QTY PART NUMBER DESCRIPTION REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS RL00 STUDDED VEE WHEEL, ECCENTRIC N0 CYLINDER " stroke FNLNMHP NYLOCK NUT M FHJNSMP /0 HEX JAM NUT D FHHMH0P0 HHCS M X D FHHMG0P0 HHCS M X FFWMHP FLAT WASHER M 0 FHHMG0P0 HHCS M X 0 FLWMGP LOCK WASHER M 0 FHHSJ0P0 HEX BOLT / X / FNLNSJP / Std NC Nylock Nut FHFNMGP HEX NUT M FFWMGP FLAT WASHER M LDX00 GUARD, MAST LDX00 CAP, MAST LDX00 GUARD SUPPORT LDX000 NUT PLATE, V TRACK 0 LDX0 MAST WELDMENT LDX00 SPACER, CYL. 0 LDX00 PIN, MAST CYL LDX000 NECK SUPPORT LDX00 NECK PLATE, REAR LDX0 HEAD LOCK PLATE LDX00 BUMPER CRUSH SLEEVE LDX0 BRKT. BUMPER FNLNMGP NYLOCK NUT M LDX0 BUMPER, MAST C C BOTTOM SPH ROD END LDX0 VEE TRACK 0 LDX0 BUMPER, HEAD LDX0 BUMPER STOP FSHMG0P0 SHCS Mx LG. SPH0 HEX HD x / 0 PSR BREATHER FSHMG0P0 SHCS M X.0 X LG. FLWMHP LOCK WASHER M FSHMH00P0 SHCS M X 0 LDX00 MAST CRUSH BLOCK FSHMH0P0 SOC. HD. CAP SCREW M X L 0 PSC0 CLAMP SW. SCREW LDX0 BUMPER, PLATE FHHMG00P0 HHCS M X 0 B B ASSEMBLED VIEW A A MAT'L PART # CAD FILE LDXRTB MAST ASSY.idw TOLERANCES UNLESS LOVESHAW an ITW Company NOTED STD OTHERWISE NOTED: PLOT DATE //00 RT., SOUTH CANAAN, PA..X = +.00 ST. ST. TITLE N/A DRAWN DATE //00 INCH.XX = +.0 ANGLES /.XXX = +.00.MA/LDXRTB STAINLESS : NO FINISH DO NOT SCALE PRINT.X =.0mm MACH. THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF METRIC.XX =.mm DWG NO SCALE LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH LDXRTB MAST ASSY N/A INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX =.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN tonys APPROVED TONYS EXPLODED VEIW 0 NOTE:. PSR to be installed after N0 (cylinder) is placed in to LDX0 (mast).. LDX00is installed inside LDX0 (mast) before bolting to LDX

41 Parts List REVISION HISTORY ITEM QTY PART NUMBER DESCRIPTION REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS LDX0 GUARD MAIN LONG LDX00 GUARD MAIN SHORT LDX00 GUARD, REAR LDX00 LEG EXTENSION FLWMHP LOCK WASHER M D LDX000 EXTENSION LOCK D LDX00 LEG LDX000 FRAME LEG RH LDX00 CROSS, TIE 0 LDX0 MAIN TIE LDX00 TAB, Z LDX00 CROSS BRACE LDX00 GUARD ANGLE LDX00 GUARD, FRT LDX0 BRACE, ANGLE FRAME LDX0 GUARD ELECT BOX LDX0 HOSE GUARD MAST LDX0 GUARD, HOSE GUARD LDX0 GUARD PNEU PANEL 0 LDX0A GUARD PNEU PANEL (BLANK) SPH RUBBER PUSH BUMPER SPH HOLE PLUG 0 0 SPH HOLE PLUG FSHMG0P0 SHCS Mx LG. 0 LDX00A SPACER, ELECT BOX LDX0 TAB, ELECT. BOX MOUNT FSHMH0P0 SOC HD Mmm LG. 0 FFWMHP FLAT WASHER M FNLNMHP NYLOCK NUT M 0 0 FFWMGP FLAT WASHER M C C FSHMH00P0 SHCS M X 0 FSHMG00P0 SOC HD M0mm LG. FHDNMGP HEX DOME NUT M AH0 WIRE / HOSE CRADLE FBHMF00P0 BHCS M X 0. X 0 LG. FHDNMFP HEX DOME NUT M FLWMFP LOCK WASHER M SPH0 TUBE CAP AH0B CABLE TIE,." LONG 0 0 SPH0 CABLE TIE HOLDER (PUSH 0 0 STYLE) FHHMG0P0 HHCS M X FHHMH00P0 HHCS M X B 0 B ASSEMBLED VIEW 0 0 EXPLODED VIEW 0 NOTE. Remove these plugs before installing pack table.. Some # A0B not shown. NOTE: A A MA 'L PART # CAD F LE LDXRTB FRAME ASSY.idw OLERANCES UNLESS LOVESHAW an ITW Company NOTED STD OTHERWISE NOTED: PLOT DA E //00 RT., SOUTH CANAAN, PA..X = 00 ITLE ST. ST. N/A DRAWN DA E //00 INCH.XX =.0 ANGLES /.XXX =.00.FRA/LDXRTB STAINLESS : NO FIN SH DO NO SCALE PRIN.X =.0mm IS DRAWING AND SUB EC MA ER HEREON IS HE EXC U IVE RO ER O MACH. ME RIC.XX =.mm DWG NO SCALE F NISH LDXRTB FRAME ASSY N/A OVESHAWI W AND IS O BE REA ED B OU AS CON IDEN IA R RIE AR IN ORMA ION HIS DRAWING OR SUB EC MA ER HERO SHA NO BE.XXX =.mm RE RODUCED O HER HAN OR OUR OWN USE OR O BE ISC OSED O O HER MA ERIAL NOTED CHECKED WI HOU HE EX RESSED W I EN CONSEN O OVESHAW I W AND WI BE RE URNED O OVESHAW I W U ON REQUES FRACTIONS + / DRAWN tonys APPROVED TONYS

42 A B C D QTY ITEM SPH SPH LDX00A SPH00 LDX00B LDX0 LDX0 ACH LDX00 Parts List PART NUMBER LDX00 LDX00 PSX SPK00 LDX00 LDX00 LDX00A LDU FSHMI0P FNLNMHP FFWMHP LDX00 LDX00 LDX00 LDX00 LDX00 FLWMHP LDX00 BRG00 LDX0 LDX00A FFWMGP FSHMG0P0 FSHMH00P0 FFHMG0P0.TDA/LDXRTB DESCRIPTION FRAME MID GUARD, DRIVE SPLIT COLLAR /" SPROCKET 0P/ T/ /"B BELT SPACER, DRIVE SHAFT KEY, DRIVE ROLLER CARTRIDGE STAND OFF SHCS M0x0 NYLOCK NUT M FLAT WASHER M BELT GUIDE BOX GUIDE FILL (TOP) BOX GUIDE FILL (END) STUD, JACKING STUD, RING LOCK WASHER M LAGGING, DRIVE ROLLER BEARING, MOUNTED DRIVE ROLLER DRIVE SHAFT FLAT WASHER M SHCS Mx LG. SHCS M X 0 FLAT HEAD SCREW M X LDXRTB BELT TENSIONER ASSY Mx0mm LG FLAT HEAD Mx0mm LG CONE POINT STUD, RING WASHER, LARGE OD KEY, DRIVE ROLLER GUARD DRIVE BOTTOM FRT PHOTOEYE BRKT PHOTOEYE GUARD, BOTTOM DRIVE LB NOTE 0 0 EXPLODED VIEW NOTE 0 N/A STD PART # //00 DO NOT SCALE PRINT DRAWN DATE //00 REVISION HISTORY DESCRIPTION DATE RELEASED //00 FRACTIONS + / ANGLES + /.X =+.0mm MACH. METRIC.XX =+.mm FINISH.XXX =+.mm.x = +.00 INCH.XX = +.0.XXX =+.00 OTHERWISE NOTED: DRAWN.BDA/LDXRTB tonys NOTED APPROVED CHECKED TONYS SCALE N/A LDXRTB DRIVE FRAME ASSY MATERIAL DWG NO TITLE APPROVED TONYS an ITW Company RT., SOUTH CANAAN, PA. LOVESHAW NOTE:. LDU is only used in a " wide cartridge assy.. Bolt is inserted thru the inside of frame. REV A LDXRTB DRIVE FRAME ASSY.idw TOLERANCES UNLESS PLOT DATE CAD FILE THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. STAINLESS : NO FINISH ST. ST. NOTED MAT'L ASSEMBLED VIEW A B C D

43 ITEM QTY Parts List PART NUMBER SP0F SPK00 LDX00 LDX00A LDX00 DESCRIPTION SPLIT COLLAR /" SPROCKET 0P/ T/ /"B SPACER, DRIVE SHAFT KEY DRIVE ROLLER BELT GUIDE REVISION HISTORY DESCRIPTION DATE REV APPROVED A RELEASED //00 TONYS.TDA/LDXRTB LDXRTB BELT TENSIONER ASSY D D LDX00 BELT LDX00 STUD, JACKING LDX00 STUD, RING 0 FSHMG0P0 SHCS M X.0 X LG. 0 FLWMGP LOCK WASHER M FNLNMGP NYLOCK NUT M FFWMGP FLAT WASHER M FHHMG0P0 HHCS M X LDX00 GUARD, DRIVE TOP FFWMIP FLAT WASHER M0 0 FSHMI0P SOC. HD. CAP SCREW M0 X LDX00 GUARD, TD FRT LDX00 SPACER, MOTOR BASE 0 LDX00 BRKT., CART MOUNT TD REAR LDX00 GUARD TD REAR TOP LDX00 GUARD TD BOTTOM LDX00 SHAFT PADDLE LDX00 SHAFT, NOSE ROLLER LDX00 NOSE SWITCH BASE WELDMENT LDX0 FRAME, TD WELDMENT SPH BUMPER FFHMF0P0 FHCS M X 0. X LG. 0 BSG0 BUSHING 0 LDX0 SPACER NOSE PADDLE 0 LDX00A ROLLER NOSE C C PSC SPRING, GUIDE PLATE LDX00 LAGGING, DRIVE ROLLER BRG00 BEARING, MOUNTED LDU WIRE GUARD (HEAD) FPHME0P0 M x 0. x mm LG N0 MECH. VALVE LDF SWITCH ELECT LDX0 SUPPORT BLOCK SWITCH 0 FFWMFP FLAT WASHER M LDX0 NOSE PADDLE LDX00 SLIDE SPACER LDX0 PADDLE, OVERSTUFF LDX0 SLIDE SPACER,SUPPORT 0 FFWMHP FLAT WASHER M LDX0 PIN, PADDLE LDX0 WEDGE TRIGGER LDX0 TOP LOAD BLOCK FFHMG0P0 FHCS Mx LG. 0 0 SPH0 GROMMET SPR0 SPRING, NOSE PADDLE FLWMEP LOCK WASHER M FLWMDP Spring Washer LDX0 DRIVE ROLLER LDX00A DRIVE SHAFT LDX0L/R GUARD TD REAR B B LDX0L/R GUARD FRONT TD EX 0 SPH0 screw Mx0mm LG. LDX0R GUARD FRONT TD EX 0 LDX0R GUARD TD REAR ED0 ESTOP ASSY. N0 TOGGLE LEVER VALVE MECH. FSHMG0P0 SHCS Mx LG. EXPLODED VIEW FHHMG00P0 HHCS M X 0 FFHMG0P0 FLAT HEAD SCREW M X FSHMH00P0 SHCS M X 0 FFHMD00P0 M X 0 FHCS SPH SCREW M x 0 LG FHFNMDP M nut 0 SPH SCREW M x LG FNLNMHP NYLOCK NUT M AH0 WIRE / HOSE CRADLE FLWMFP LOCK WASHER M FHDNMFP HEX DOME NUT M FHDNMGP HEX DOME NUT M 0 FLWMHP LOCK WASHER M LDX00A STUD, RING SPH Mx0mm LG FLAT HEAD SPH Mx0mm LG CONE POINT 0 SPH00 WASHER, LARGE OD ASSEMBLED VIEW FFHMG0P0 FHSC Mx LG. A A AH0B CABLE TIE." LONG MA 'L PART # CAD F LE LDXRTB TOP DRIVE TOLERANCES FRAME ASSY UNLESS with NEW LOVESHAW PADDLE rev.idw an ITW Company SPH0 CABLE TIE HOLDER (PUSH STYLE) NOTED STD OTHERWISE NOTED: PLOT DA E //00 RT., SOUTH CANAAN, PA. FBHMF0P0 HEX SOC. BUTT. HD. SCREW.X = 00 ST. ST. DRAWN DA E ITLE N/A //00 INCH.XX =.0 LDX00 NECK, MAST ANGLES / DO NO SCALE PRIN.XXX =.00 LDXRTB TOP DRIVE ASSY. STAINLESS : NO FIN SH LDX0 GUARD, TD TOP.X =.0mm IS DRAWING AND SUB EC MA ER HEREON IS HE EXC U IVE RO ER O MACH. ME RIC.XX =.mm DWG NO SCA E LDX00B KEY, DRIVE ROLLER OVESHAWI W AND IS O BE REA ED B OU AS CON IDEN IA R RIE AR F NISH LDXRTB TOP DRIVE FRAME ASSY N A with NEW PA IN ORMA ION HIS DRAWING OR SUB EC MA ER HERO SHA NO BE.XXX =.mm RE RODUCED O HER HAN OR OUR OWN USE OR O BE ISC OSED O O HER MA ERIAL NOTED CHECKED WI HOU HE EX RESSED W I EN CONSEN O OVESHAW I W AND WI BE RE URNED O OVESHAW I W U ON REQUES FRACTIONS + / DRAWN tonys APPROVED TONYS

44 REVISION HISTORY REV DESCRIPTION DATE APPROVED Parts List A RELEASED //00 TONYS ITEM QTY PART NUMBER DESCRIPTION AHG FITTING, STRAIN PG FFWSDP FLAT WASHER / FLWSDP LOCK WASHER / FHHSG0P0 HH / x /" LG. SEE MOTOR CHART MOTOR B SEE SPROCKET SPROCKET B CHART NOTE: See motor chart for motor part number. A See sprocket chart for sprocket part number. A MAT'L PART # CAD FILE LDXRTB MOTOR ASSY manual.idw NOTED STD PLOT DATE //00 ST. ST. N/A DRAWN DATE //00 INCH.X = +.00 TITLE.XX = +.0 ANGLES + / STAINLESS : NO FINISH DO NOT SCALE PRINT.XXX = +.00.X = +.0mm METRIC.XX = +.mm MACH. FINISH DWG NO SCALE LDXRTB MOTOR ASSY manual n/a THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY.XXX = +.mm MATERIAL NOTED CHECKED INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE DRAWN APPROVED RETURNED TO LOVESHAWITW UPON REQUEST. tonys TOLERANCES UNLESS OTHERWISE NOTED: FRACTIONS + / LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. LDXRTB motor & sprocket information TONYS

45 DRIVE MOTOR SPROCKET OPTIONS Note: Refer to drawing previous page Motor Selection: Part number Description Position 0000 / hp gear motor 0V0V/00Hz Top drive 0000 / hp gear motor 0V0V/00Hz Bottom drive Part number Description Position 0000 / hp gear motor 0V0V/00Hz PH Top drive 0000 / hp gear motor 0V0V/00Hz PH Bottom drive Drive Motor Sprocket Selection: Part number Belt Speed Feet per minute Electrical frequency Hz SPK0 ft/min 0 Hz SPK00 ft/min 0 Hz Part number Belt Speed Feet per minute Electrical frequency Hz SPK0 ft/min 0 Hz SPK0 ft/min 0 Hz Note: When changing sprockets to modify belt speed it is necessary to change the overall length of the drive chain. Belt speed Bottom Drive Top drive ft/min Full links, Master link Full links, Half links Master link ft/min Full links, Master link Full links, Master link Part numbers: #0 Chain HC0 Half link HC0 Master Link HC0

46 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS 0 0 B B EXPLODED VIEW ASSEMBLED VIEW Parts List ITEM QTY PART NUMBER DESCRIPTION FLWMHP LOCK WASHER M FHHMH0P0 HHCS M X A LDX0 BAR, TENSIONER A LDX0 SHAFT, JACKING FFWSFP FLAT WASHER / MAT'L PART # CAD FILE LDXRTB BELT TENSIONER TOLERANCES ASSY.idw LDX0 RING, TENSIONER SPACER UNLESS LOVESHAW an ITW Company NOTED STD PLOT DATE //00 OTHERWISE NOTED: SPH00 WASHER, LARGE OD RT., SOUTH CANAAN, PA..X = +.00 ST. ST. DRAWN DATE TITLE PSC0 SPRING N/A //00 INCH.XX = +.0 ANGLES + /.XXX = + DO NOT SCALE PRINT.00 LDX0 IDLER, ROLLER STAINLESS : NO FINISH.BTA/LDXRTB 0 BRG00 BEARING THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY.X = +.0mm METRIC.XX = +.mm MACH. FINISH DWG NO.TDA/LDXRTB SCALE N/A FHFNMHP HEX NUT, M INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER.XXX = +.mm MATERIAL NOTED CHECKED FRACTIONS + / DRAWN APPROVED TONYS WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. tonys

47 REVISION HISTORY REV DESCRIPTION DATE APPROVED Parts List A RELEASED //00 TONYS ITEM QTY PART NUMBER DESCRIPTION PSC SPHERICAL ALIGN BEARING FHJNSIP HEX JAM NUT, / N0 CYLINDER FHJNSMP /0 HEX JAM NUT D FFWSEP FW / D FFWMHP FLAT WASHER M FNLNMHP NYLOCK NUT M FFHMG0P0 FHCS M X.0 X LG. N00 SPEED CONTROL, 0 DEG 0 LDX000 SIDERAIL SUPPORT BRKT. LDX00 SIDERAIL TUBE BLOCK LDX00 LINK BAR LDX00 SIDE RAIL WELDMENT (LH) LDX00 SIDERAIL WELDMENT (RH) LDX00 SIDERAIL TUBE TEE LDX00 SIDE RAIL TUBE LDX00 ROD EXT. SR LDX00 NUT PLATE, SR FFHMH00P0 FLAT HEAD CAP SCREW M X 0 LG. 0 LDX0 CLAMP LINK BAR SPH Mx0mm LG CONE POINT SPH0 PLUG, BALL HEAD FFWMGP FLAT WASHER M FSHMG0P0 SHCS Mx LG. LDX0 SHIM, SIDERAIL LDX00 BLOCK, LOCK PSU HAND KNOB FHJNMIP HEX JAM NUT, M0, PLATED C LDX0 LOCK ROD SIDERAIL C 0 FBHMF0P0 HEX SOC. BUTT. HD. SCREW FNLNMIP NYLOCK NUT M0 ASSEMBLED VIEW FSSMH00B SS M x 0mm LG. SPC00 COLLAR FULL SPLIT " BORE B B 0 A A MAT'L PART # CAD FILE LDXRTB SIDE RAIL TOLERANCES ASSY.idw UNLESS LOVESHAW an ITW Company NOTED STD OTHERWISE NOTED: PLOT DATE //00 RT., SOUTH CANAAN, PA..X = +.00 TITLE EXPLODED VIEW ST. ST. N/A DRAWN DATE //00 INCH.XX = +.0 ANGLES /.XXX = +.00.SRA/LDXRTB STAINLESS : NO FINISH DO NOT SCALE PRINT.X =.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX =.mm DWG NO SCALE LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH LDXRTB SIDE RAIL ASSY N/A INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX =.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN tonys APPROVED TONYS

48 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS D D 0 C C ASSEMBLED VIEW TOP VIEW EXPLODED B B Parts List FINISH ITEM QTY PART NUMBER DESCRIPTION LDX00 NUT PLATE PT CR00 ROLLER 0 LDX00 PACK TABLE SHORT 0 FLWMGP LOCK WASHER M FSHMG0P0 SHCS Mx LG. LDX00 BASE PLATE FLWMHP LOCK WASHER M FNLNMHP NYLOCK NUT M FHHMH0P0 HHCS M X 0 FSHMH0P0 SHCS Mx FMB RUBBER BUMPER BOTTOM VIEW EXPLODED LDX0 BUMPER ANGLE LDX00 CAP, ROLLER SMALL NOTE:. LDX00 is mounted inside of the frame leg as LDX00 ANGLE, ROLLER nut plate for mounting of table. SUPPORT SHORT ACH PHOTOEYE A LDX00 BRACKET, PE ANGLE MAT'L LDXRTB PACK TABLE TOLERANCES ASSY SHORT.idw UNLESS LOVESHAW an ITW Company A PART # CAD FILE FNLNMGP NYLOCK NUT M //00 OTHERWISE NOTED: RT., SOUTH CANAAN, PA. NOTED STD PLOT DATE N/A //00 LDXRTB PACK TABLE ASSY.X = +.00 TITLE ST. ST. DRAWN DATE.XX = +.0 ANGLES / + INCH DO NOT SCALE PRINT SHORT +.XXX =.00 STAINLESS : NO FINISH.X + =.0mm MACH..ITA/LDXRTB/SH N/A THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF DWG NO SCALE METRIC.XX = +.mm LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY.XXX + =.mm INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE NOTED MATERIAL CHECKED REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER FRACTIONS + / TONYS WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. tonys DRAWN APPROVED

49 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS Parts List ITEM QTY PART NUMBER DESCRIPTION D CR00 ROLLER FLWMGP LOCK WASHER M D FSHMG0P0 SHCS Mx LG. FNLNMHP NYLOCK NUT M LDX0 PACK TABLE EXT. LDX0 CAP, ROLLER SHORT LDX0 ANGLE, ROLLER SUPPORT SHORT FHHMH0P0 HHCS M X LDX0 SUPPORT PLATE, PACK TABLE C C B B EXPLODED VIEW ASSEMBLED VIEW A MAT'L PART # CAD FILE LDXRTB PACK TABLE TOLERANCES ASSY UNLESS INCH.IDW A NOTED STD OTHERWISE NOTED: PLOT DATE //00.X = +.00 ST. ST. TITLE N/A DRAWN DATE //00 INCH.XX = +.0 ANGLES + /.XXX = +.00.ITA/LDXRTB/ STAINLESS : NO FINISH DO NOT SCALE PRINT.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO SCALE LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH LDXRTB PACK TABLE ASSY INCH N/A INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. DRAWN tonys APPROVED TONYS FRACTIONS + / LOVESHAW an ITW Company RT., SOUTH CANAAN, PA.

50 A B C D QTY LDX0 Parts List PART NUMBER CR00 FLWMGP FSHMG0P0 FNLNMHP LDX0 LDX0 FHHMH0P0 LDX0 EXPLODED VIEW ITEM DESCRIPTION ROLLER LOCK WASHER M SHCS Mx LG. NYLOCK NUT M PACK TABLE EXT. " CAP, ROLLER " HHCS M X SUPPORT PLATE, PACK TABLE ANGLE, ROLLER SUPPORT " STD DO NOT SCALE PRINT //00 //00 DRAWN DATE REVISION HISTORY DESCRIPTION DATE RELEASED //00 ANGLES + / FRACTIONS + /.X =+.0mm MACH. METRIC.XX =+.mm FINISH.XXX =+.mm.x = +.00 INCH.XX = +.0.XXX =+.00 OTHERWISE NOTED: DRAWN.ITA/LDXRTB/ tonys NOTED APPROVED CHECKED TONYS SCALE.x LDXRTB PACK TABLE ASSY INCH MATERIAL DWG NO TITLE APPROVED TONYS an ITW Company RT., SOUTH CANAAN, PA. LOVESHAW ASSEMBLED VIEW REV A LDXRTB PACK TABLE ASSY INCH.idw TOLERANCES UNLESS PLOT DATE CAD FILE THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. STAINLESS : NO FINISH ST. ST. PART # MAT'L NOTED N/A A B C D

51 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED //00 TONYS D D C C EXPLODED VIEW B B Parts List ITEM QTY PART NUMBER DESCRIPTION CR00 ROLLER FLWMGP LOCK WASHER M FSHMG0P0 SHCS Mx LG. FNLNMHP NYLOCK NUT M LDX0 PACK TABLE EXT. " LDX0 CAP, ROLLER " FHHMH0P0 HHCS M X LDX0 SUPPORT PLATE, PACK TABLE A MAT'L PART # CAD FILE LDXRTB PACK TABLE TOLERANCES ASSY UNLESS INCH.idw LOVESHAW an ITW Company A LDX0 ANGLE, ROLLER NOTED STD OTHERWISE NOTED: PLOT DATE //00 RT., SOUTH CANAAN, PA. SUPPORT ".X = +.00 ST. ST. DRAWN DATE TITLE N/A //00 INCH.XX = +.0 ANGLES + /.XXX = + DO NOT SCALE PRINT.00.ITA/LDXRTB/ STAINLESS : NO FINISH.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO SCALE LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH LDXRTB PACK TABLE ASSY.x INCH INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN tonys APPROVED TONYS ASSEMBLED VIEW

52 REVISION HISTORY REV DESCRIPTION DATE APPROVED A RELEASED /0/00 TONYS D D C C B B EXPLODED VIEW ASSEMBLED VIEW Parts List ITEM QTY PART NUMBER DESCRIPTION CR00 ROLLER FLWMGP LOCK WASHER M FSHMG0P0 SHCS Mx LG. FNLNMHP NYLOCK NUT M LDX0 PACK TABLE EXT.." LDX00 CAP, ROLLER." LDX0 ANGLE, ROLLER SUPPORT." A FHHMH0P0 HHCS M X MAT'L PART # CAD FILE LDXRTB PACK TABLE TOLERANCES ASSY UNLESS INCH.IDW LOVESHAW an ITW Company A LDX0 SUPPORT PLATE, NOTED STD OTHERWISE NOTED: PLOT DATE /0/00 RT., SOUTH CANAAN, PA. PACK TABLE.X = +.00 ST. ST. DRAWN DATE TITLE N/A /0/00 INCH.XX = +.0 ANGLES + /.XXX = + DO NOT SCALE PRINT.00.ITA/LDXRTB/. STAINLESS : NO FINISH.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO SCALE LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH LDXRTB PACK TABLE ASSY INCH N/A INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL NOTED CHECKED WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN tonys APPROVED TONYS

53

54

55

56 LITTLE DAVID OWNERS MANUAL CAC0XCACX THE LOVESHAW CORPORATION LOVESHAW EUROPE 0 EASTON TURNPIKE, BOX UNIT, BRUNEL GATE SOUTH CANAAN, PA W. PORTWAY INDUSTRIAL ESTATE ANDOVER, HAMPSHIRE SP0SL TEL: (0) ENGLAND FAX: (0) 0

57 Part and Instruction Manual Loveshaw Pressure Sensitive Tape Cartridge CAC0 wide tape CAC wide tape This is a combined manual for the CAC0 wide tape and the CAC wide tape. Take care when ordering parts. Make sure it is for the correct width cartridge. For stainless steel cartridge parts add the suffix SS to the part numbers depicted in the assembly drawings.

58 Theory of Operation: Pressure sensitive tape is applied to the corrugated box as it passes by the cartridge. The box will contact the front arm roller which has pressure sensitive tape adhesive side facing outward towards the oncoming box. The front leading side of the box will contact the front roller arm and the tape will adhere to the box. As the box continues to move forward the front roller arm and knife arm will be rotated into the frame of the cartridge. The amount of force exerted on the box as tape is being applied is adjustable by changing the position of the main spring. The front arm initial application force can be set to accommodate the strength of the box as well as the sturdiness of the contents in the box. As the front arm application roller transitions from the leading panel of the box to the top major flaps a separate wipe down spring is engaged. The sole purpose of this spring is to add speed to the rear wipe roller actuation to insure the rear tape tab is completely wiped to the rear trailing panel of the box. At this time the knife arm is retracted into the cartridge and the knife blade guard is fully retracted uncovering the blade. As the knife arm rotated into the cartridge the knife activation spring extends, generating cut force. As the box proceeds pass the cartridge the front arm roller will no longer contact the major flaps of the box, but the rear wipe roller will still contact the major flaps. Eventually as the box travels the knife arm will completely stop contacting the major flaps of the box. This will allow the knife arm to travel back towards its home position allowing the knife blade to puncture and cut through the tape. As the box continues move the rear wipe arm roller will no longer contact the major flaps of the box. This will allow the wipe arm roller to spring out of the cartridge and contact the rear tab length of tape and press against the trailing panel of the box. The rear wipe arm roller booster spring starts the wipe and the main cartridge spring finishes the wipe sequence. The box travelling pass the cartridge is the vehicle which pulls the tape through the cartridge. The cartridge is design to run most pressure sensitive tapes with no required adjustments. However in some cases it may be necessary to adjust tape tensions. The cartridge will operate at speeds up to 0 feet/minute.

59 Important Safety Notices: Before installing operating or servicing the tape cartridges read carefully and understand the following precautions: Never service the tape cartridges when installed in an operating machine. Use lock out / tag out protocols before installing or removing cartridges from machinery. Do not bypass or remove safety guard on knife blade. Observe caution when near tape cartridge knife. The knife blade is protected by a locking cover which is held closed by the link bar. Never make any adjustments to the tape cartridges when installed in an operating machine.

60 Tape Threading: The first step is to place the tape roll, on the cartridge exspandable tape core. Rotate the tape tension arm clockwise until it locks in place in its fully open position. (refer to figure ) The tape core diameter is adjustable by turning the adjustor nut. Turning the adjustor nut c.w. the core diameter increases and turning it c.c.w. the tape core diameter decreases. Decrease the tape core enough in order to place the tape roll on the core. Now turn the adjustor nut clockwise until the tape roll is snuggly held. (refer to figure) Tape roll must be placed on tape core with adhesive side of tape facing to the right. Refer to figure and for proper orientation. Figure Figure Adhesive side Adjustor nut Continue threading the tape over the upper and lower white tension arm rollers. Threading arrows are installed throughout the tape path of the cartridge to aid in threading. The back of the tape, the non adhesive side rides against the front of the rollers. It is important to insure that the tape tension arm is not bent; since this will cause the tape not to track properly through the cartridge. Refer to figure.

61 Figure Tension arm upper roller Tension arm Tension arm lower roller Arm lock release The tape is then threaded around the knurled tape tension roller. The adhesive side of the tape contacts the knurled roller. Refer to figure. Figure Knurled tension roller

62 The tape is then threaded between black knurled roll and the tape guide plate. The adhesive side of the tape will contact the two tape guide rollers as it is pulled through the guide plate assembly until it is at rest on the front arm roller. The adhesive side of the tape will be facing away from the front arm roller. Refer to figure. Figure Black knurled roller Tape guide plate Tape guide rollers Front arm roller

63 Adjustments: Aligning tape : Aligning tape side to side with in the cartridge frame is done by changing the position of the tape core. This is done by first loosening the tape core locking screw with a mm hex key. Turn the tape core locking screw counter clockwise allowing for the desired amount of adjustment to be made. Now turn the tape core height adjusting nut until the desired result is obtained. By turning the tape core height adjusting nut clockwise the tape core height position will decrease moving the tape closer to the mill stand side of the cartridge. By turning the tape core height adjusting nut counter clockwise the tape core height position will increase. This will make the tape track further away from the mill stand. After each adjustment always tighten the tape core locking screw. Failure to do so will allow the tape core position to change as tape is being pulled of f the tape roll. Refer to figure Tape core height adjusting nut Figure Tape core height locking screw Tape core friction drag adjustor ring

64 Setting tape core drag: The tape core drag setting is factory set to not allow a full roll of tape to free wheel as tape is being pulled off it. The tape tension arm assembly automatically adjusts for the proper amount of tape tension to be applied as the tape roll diminishes in diameter as tape is applied. The drag setting may need to be adjusted if the tape cartridge is being operated at high speed or if the tape adhesive is causing the roll to over rotate as the tape it is being pulled of the roll. Refer to figure. Setting the knurled tension roller: The knurled tension roller is factory set to its minimum resistance setting. This setting works for all standard tape applications. The tension roller setting may need to be adjusted if a thick mill tape is being used. By increasing the tension it aids in cutting the tape. Refer to figure. Figure Tension roller adjustor nut Setting main spring tension: Setting the main spring tension is done by moving the end of the spring to a different preset position. The main spring tension is factory set to a mid position. The spring is set from lightest to stoutest dependant on the strength of the corrugated box and the fill of the contents. Void filled,

65 weak corrugated boxes would be set to the lightest setting while strong corrugated box with overfill would process better with the main spring set stronger. The main spring only effects the application and wipe rollers. Refer to figure. Strongest setting Figure Weakest setting Booster adjustment Main spring tension adjustment Main spring Booster spring Setting booster spring compression The booster spring aids in rear tab wipe. The booster spring preloads the wipe roller arm so when the trailing edge of the box releases the wipe roller the arm can travel out a higher rate of speed and contact the rear tab and secure it to the back panel of the box. The booster adjuster is

66 factory set to lightly engage when the front roller arm is completely retracted. The booster setting is adjusted stronger when the cartridge is operated at higher application speeds. Refer to figure. Setting the rear tab cut adjustor: The rear tab cut adjustor is factory set to operate at 0 to 0ft/min belt speed. If the cartridge is operating at higher speeds the adjustor would need to move in order to shorten the rear tab length. The adjustor only alters the rear tab length. The front tab length is fixed and cannot be adjusted. Refer to figure. Figure Decrease Increase Tab adjustor Front arm stopper adjustment: The front arm stop adjustment is factory set to insure that the front arm roller stays in contact with major flaps of the box. This allows for a tight tape seal across the horizontal length of the box. The adjustor does not 0

67 need to be adjusted for normal applications. In some cases it may be necessary to adjust the stop depending on the type of machine that the cartridge is being used in. If the cartridge is placed in a machine and the tape is not being applied to the major flaps with enough pressure an adjustment will be necessary. This will be evident by inspecting the box as it exits the machine. Normal symptoms include the tape bridging across the major flaps, or the tape bunching up on the major flaps after the tape was cut. Refer to figure 0. Figure 0 Front arm stopper Jam nut

68 Maintenance: Application / Wipe roller replacement: Roller replacement is a tool less procedure. Simply push down on retaining pin and slide roller off the shaft. Install new roller in opposite fashion. Take caution to install replacement roller with undercut facing toward arm away from retaining pin. Refer to figure. Figure Retaining pin Knife blade replacement: Knife blade replacement is a tool less procedure. Simply push down on release bar and pull knife blade out. Fold back the knife guard by first

69 rotating the front roller arm inward towards the rear wipe arm. Then rotate the knife guard back until the knife blade is fully exposed. While holding the knife guard open slowly release the front roller arm and allow it to extend outward. This will allow the knife guard locking mechanism to hold the knife guard open for easy blade replacement. The knife blades have open slots to allow for easy slide on / off replacements. The knife blade is notch for proper orientation of the blade. Refer to figure A and B. Oil Pad: Regularly lubricate oil pad with SAE #0 nondetergent oil. Never use penetrating type oil; this will dissolve the adhesive which secures the pad to the knife guard. Refer to figure A. Warning: Use extreme care when working near the knife blade. The blade is extremely sharp. If care is not taken severe personal injury can occur. Figure A Locating notch OIL PAD

70 Figure B Blade release bar Knife guard is shown open in both figures.

71 Troubleshooting: Problem Cause Corrective Action The tape is not cut, or the cut Knife blade is damaged or Replace knife blade. is not clean. needs to be cleaned.. Front tab length too long. Rear tab not fully wiped down Rear tab too long. Tape core does not fit into machine cartridge opening. (bottom) Tape tension needs to be increased. Tape is not centered on rollers. Knife spring missing or worn. Blade is not lubricated. Cartridge threaded incorrectly. Tape tension needs to be increased. Tape is not centered on rollers. Rear tab length too long. Main spring tension to weak. Booster spring not engaged. Tab adjustor not set properly. Knife spring worn. Not enough tape tension Tape tension arm either misaligned or bent. Increase drag on knurled tension roller. Adjust tape core height. Replace spring. Oil felt pad on knife guard. Check threading arrows on cartridge. Increase drag on knurled tension roller. Adjust tape core height. Adjust rear tab adjustor. Adjust main spring tension. Adjust booster spring compression. Adjust rear tab adjustor. Replace knife spring. Increase drag on knurled tension roller. Straighten arm so that is parallel with mill stand.

72 REVISION HISTORY REV DESCRIPTION DATE BY A RELEASED //00 AMYR B M.C.R. #000 //00 AMYR D D PARTS FOR.CAC0 " CARTRIDGE C ITEM QTY N/S Parts List PART NUMBER DESCRIPTION.FRACAC0 FRONT ROLLER ARM ASSEMBLY.RRACAC0 REAR ROLLER ARM ASSEMBLY.KAACAC0 KNIFE ASSEMBLY.TCA TAPE CORE ASSEMBLY ".TAACAC0 TENSION ARM ASSEMBLY.CAC0 SERIES " BASE ASSEMBLY.TRA0 TENSION ROLLER ASSEMBLY SPR0 MAIN SPRING CARTRIDGE CAC000 TIE BLOCK,TOP LOAD BRKT C PARTS FOR.CAC " CARTRIDGE B ITEM QTY N/S Parts List PART NUMBER DESCRIPTION.FRACAC FRONT ROLLER ARM ASSEMBLY.RRACAC REAR ROLLER ARM ASSEMBLY.KAACAC KNIFE ASSEMBLY.TCA TAPE CORE ASSEMBLY ".TAACAC TENSION ARM ASSEMBLY.CAC SERIES " BASE ASSEMBLY.TRA TENSION ROLLER ASSEMBLY CAC000/ TIE BLOCK, TOPLOAD BRKT B A MAT'L PART # CAD FILE OVERVIEWCAC0XX TOLERANCES UNLESS C.R.S. STD OTHERWISE NOTED: PLOT DATE //00.X = +.00 ST. ST. DRAWN DATE TITLE //00 INCH.XX = +.0 ANGLES + /~.XXX = +.00 STAINLESS : NO FINISH DO NOT SCALE PRINT.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY FINISH INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN LOVESHAW an ITW Company RT., SOUTH CANAAN, PA..CAC0 /.CAC SERIES OVERVIEW.CAC0 /.CAC SERIES SCALE AMYR CHECKED APPROVED A

73 REVISION HISTORY REV DESCRIPTION DATE BY D UPDATED //00 BJF D C 0 PARTS FOR.CAC0 " CARTRIDGE D Parts List ITEM QTY PART NUMBER DESCRIPTION CAC00000 MAIN FRAME CAC000 SIDE FRAME MEDIUM CAC0000 TIE SHAFT CAC000 MILLSTAND CAC000 SHAFT MILLSTAND CAC0000A SPRING SHAFT SPH RUBBER BUMPER CAC000 STOP MOUNT FFHMF0P0 FHCS M X 0. X LG. 0 FFHMG0P0 FHCS M X.0 X LG. FHJNMFP M HEX JAM NUT 0 FFHMF0P0 FHCS M X LG. FLWMFP LOCK WASHER M FHFNMFP HEX NUT M CAC000 STOPPER FRONT ARM CAC000A STOPPER FRONT ARM C SPR0 MAIN SPRING CARTRIDGE CAC000 SIDE FRAME, SMALL CAC000/ SHAFT 0 CAC0000A TIE SHAFT CAC000 SECONDARY FRAME CAC000 SPRING STUD CAC000A NYLON SPACER B PARTS FOR.CAC " CARTRIDGE Parts List ITEM QTY PART NUMBER DESCRIPTION CAC00000 MAIN FRAME CAC000 SIDE FRAME MEDIUM CAC0000/ TIE SHAFT, " CAC000 MILLSTAND CAC000/ SHAFT MILLSTAND CAC0000/A SPRING SHAFT " B SPH RUBBER BUMPER CAC000 STOP MOUNT FFHMF0P0 FHCS M X 0. X LG. 0 FFHMG0P0 FHCS M X.0 X LG. FHJNMFP M HEX JAM NUT 0 FFHMF0P0 FHCS M X 0. X LG. FLWMFP LOCK WASHER M FHFNMFP HEX NUT M CAC000 STOPPER FRONT ARM CAC000A STOPPER FRONT ARM PSC00 MAIN SPRING CARTRIDGE CAC000 SIDE FRAME, SMALL CAC000 SHAFT 0 CAC0000A/ TIE SHAFT, " CAC000 SECONDARY FRAME CAC000 SPRING STUD CAC000/A NYLON SPACER A LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. MAT'L PART # CAD FILE MAIN ASSY EXP.idw TOLERANCES UNLESS STD OTHERWISE NOTED: PLOT DATE //00.X = +.00 ST. ST. DRAWN DATE TITLE //00 INCH.XX = +.0 ANGLES + /.XXX = +.00 STAINLESS : NO FINISH DO NOT SCALE PRINT.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO FINISH.CAC0 /.CAC SERIES LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN brycef BASE ASSEMBLY " / " SCALE CHECKED APPROVED /: A

74 REVISION HISTORY REV DESCRIPTION DATE BY C UPDATED //00 BJF PARTS FOR.CAC0 " CARTRIDGE Parts List D ITEM QTY PART NUMBER DESCRIPTION CAC0000 FRONT ROLLER ARM SPH WAVE WASHER CAC0000 TAPE GUIDE PLATE CAC0000 LINK BAR CAC000 BUSHING, OILITE SPH / BRONZE WASHER SPH SNAP RING, mm BSG00 mm FLANGE BUSHING SPR0 SPRING, COMPRESSION 0 CAC0000 SLIDING BLOCK CAC0000 BUSHING SPH EXT. SNAP RING, mm CAC0000 ROLLER SPH M WASHER CAC000 KNIFE GUARD LOCK BSG0 BUSHING CAC000 SMALL ROLLER C FBHME0P0 M x BUTTON HEAD FFHMG0P0 FHCS M X.0 X LG. 0 BSG0 BUSHING mm FBHME00P0 M x 0 PAN HEAD SCREW FHFNMEP M HEX NUT SPR0 EXTENSION SPRING.FPACAC0 FINGER PLATE ASSEMBLY FFWMFP FLAT WASHER M FHJNMDP M x 0. Hex Nut FSHMD0P0 CAP SCREW M x LG..SA0 SHAFT ASSEMBLY 0 D C PARTS FOR.CAC " CARTRIDGE Parts List ITEM QTY PART NUMBER DESCRIPTION CAC0000/ FRONT ROLLER ARM SPH WAVE WASHER CAC0000/ TAPE GUIDE PLATE " B CAC0000 LINK BAR CAC000 BUSHING, OILITE SPH / BRONZE WASHER SPH SNAP RING, mm BSG00 mm FLANGE BUSHING SPR0 SPRING, COMPRESSION 0 CAC0000 SLIDING BLOCK CAC0000 BUSHING SPH EXT. SNAP RING, mm CAC0000/ ROLLER SPH M WASHER CAC000 KNIFE GUARD LOCK BSG0 BUSHING CAC000/ SMALL ROLLER FBHME0P0 M x BUTTON HEAD FFHMG0P0 FHCS M X.0 X LG. 0 BSG0 BUSHING mm FBHME00P0 M x 0 PAN HEAD SCREW FHFNMEP M HEX NUT A SPR0 EXTENSION SPRING.FPACAC FINGER PLATE ASSEMBLY FFWMFP FLAT WASHER M FHJNMDP M x 0. Hex Nut FSHMD0P0 CAP SCREW M x LG..SA SHAFT ASSEMBLY 0 LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. MAT'L PART # CAD FILE FRACAC0/ TOLERANCES UNLESS STD OTHERWISE NOTED: PLOT DATE //00.X = +.00 ST. ST. DRAWN DATE TITLE //00 INCH.XX = +.0 ANGLES + /.XXX = +.00 STAINLESS : NO FINISH DO NOT SCALE PRINT.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO FINISH.FRACAC0/ LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN brycef FRONT ROLLER ARM SCALE CHECKED APPROVED /: B A

75 REVISION HISTORY REV DESCRIPTION DATE BY D UPDATED //00 BJF D D PARTS FOR.CAC0 " CARTRIDGE C 0 ITEM 0 QTY Parts List PART NUMBER DESCRIPTION CAC0000 REAR ROLLER ARM CAC0000 ROLLER SPH WAVE WASHER BSG0 BUSHING mm CAC000 STANDOFF SPH ROD END, M CAC0000 SLIDING ROD SPR0 COMPRESSION SPRING SPH RETAINING RING mm CAC000 SPACER SPH SHAFT COLLAR FFHMG0P0 FL. HD. CAP SCREW M X.0 X LG. FBHMF0P0 BUTT. HD. CAP SCREW M X LG. FHFNMGP HEX NUT M.SA0 SHAFT ASSEMBLY C B ITEM 0 QTY PARTS FOR.CAC " CARTRIDGE Parts List PART NUMBER DESCRIPTION CAC0000 REAR ROLLER ARM CAC0000/ ROLLER SPH WAVE WASHER BSG0 BUSHING mm CAC000 STANDOFF SPH ROD END, M CAC0000 SLIDING ROD SPR0 COMPRRESSION SPRING SPH RETAINING RING mm CAC000 SPACER SPH SHAFT COLLAR FFHMG0P0 FL. HD. CAP SCREW M X.0 X LG. FBHMF0P0 BUTT. HD. CAP SCREW M X LG. FHFNMGP HEX NUT M.SA SHAFT ASSEMBLY B A LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. MAT'L PART # CAD FILE RRACAC0.idw TOLERANCES UNLESS STD OTHERWISE NOTED: PLOT DATE /0/00.X = +.00 ST. ST. DRAWN DATE TITLE //00 INCH.XX = +.0 ANGLES + /.XXX = +.00 STAINLESS : NO FINISH DO NOT SCALE PRINT.X = +.0mm THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF MACH. METRIC.XX = +.mm DWG NO FINISH.RRACAC0/ LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE.XXX = +.mm REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER MATERIAL WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. FRACTIONS + / DRAWN AMYR REAR ROLLER ARM ASSEMBLY SCALE CHECKED APPROVED A

76 REVISION HISTORY REV DESCRIPTION DATE BY A RELEASED //00 BJF D D C ITEM QTY PARTS FOR.CAC0 " CARTRIDGE Parts List PART NUMBER DESCRIPTION CAC000/A SHAFT, KNURLED ROLLER CAC000 LOCKING WASHER PSC0A WASHER, SPRING BRG0 BEARING BRG0 BEARING CAC000 BRAKE WASHER FNLNMIP NYLOCK NUT M0 CAC000 KNURLED ROLLER C B ITEM QTY PARTS FOR.CAC " CARTRIDGE Parts List PART NUMBER DESCRIPTION CAC000/A SHAFT, KNURLED ROLLER CAC000 LOCKING WASHER PSC0A WASHER, SPRING BRG0 BEARING BRG0 BEARING CAC000 BRAKE WASHER FNLNMIP NYLOCK NUT M0 CAC000/ KNURLED ROLLER B A MAT'L PART # CAD FILE.TRA0A.TRAA C.R.S. STD PLOT DATE //00 ST. ST. DRAWN DATE //00 STAINLESS : NO FINISH DO NOT SCALE PRINT THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. TOLERANCES UNLESS OTHERWISE NOTED:.X = +.00 TITLE INCH.XX = +.0 ANGLES + /.XXX = +.00.X = +.0mm MACH. METRIC.XX = +.mm DWG NO FINISH.XXX = +.mm MATERIAL FRACTIONS + / DRAWN LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. TENSION ROLLER ASSEMBLY CAC0/.TRA0A/.TRAA AMYR SCALE CHECKED APPROVED A

77 REVISION HISTORY REV DESCRIPTION DATE BY C UPDATED //00 BJF D D 0 C ITEM 0 PARTS FOR.CAC0 " CARTRIDGE Parts List QTY PART NUMBER DESCRIPTION SPH RETAINING RING 0mm CAC000 SPRING STUD CAC000 TAPE TENSION ARM SHAFT STEPPED CAC000 TAPE TENSION ARM CAC000 TAPE TENSION ARM SHAFT SPR0 CATCH SPRING SPH BRONZE WASHER, / SPR0 EXTENSION SPRING CAC000 CATCH FFHMG0P0 FL. HD. CAP SCREW M X.0 X LG. FFHMF0P0 FL. HD. CAP SCREW M X LG. SPH CIRCLIP 0mm CAC000 TAPERED ROLLER CAC000 TAPE TENSION ARM ROLLER FFWMHP FLAT WASHER M C B ITEM 0 PARTS FOR.CAC " CARTRIDGE Parts List QTY PART NUMBER DESCRIPTION SPH RETAINING RING 0mm CAC000 SPRING STUD CAC000/ TAPE TENSION ARM SHAFT STEPPED CAC000 TAPE TENSION ARM CAC000/ TAPE TENSION ARM SHAFT SPR0 CATCH SPRING SPH BRONZE WASHER, / SPR0 EXTENSION SPRING CAC000 CATCH FFHMG0P0 FL. HD. CAP SCREW M X.0 X LG. FFHMF0P0 FL. HD. CAP SCREW M X LG. SPH CIRCLIP 0mm CAC000/ TAPERED ROLLER CAC000/ TAPE TENSION ARM ROLLER FFWMHP FLAT WASHER M B A MAT'L C.R.S. PART # STD CAD FILE.TAACAC0 PLOT DATE /0/00 ST. ST. DRAWN DATE //00 STAINLESS : NO FINISH DO NOT SCALE PRINT THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. TOLERANCES UNLESS OTHERWISE NOTED:.X = +.00 TITLE INCH.XX = +.0 ANGLES + /.XXX = +.00.X = +.0mm MACH. METRIC.XX = +.mm DWG NO FINISH.XXX = +.mm MATERIAL FRACTIONS + / DRAWN LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. TAPE TENSION ARM ASSEMBLY.TAACAC0/ AMYR SCALE CHECKED APPROVED A

78 REVISION HISTORY REV DESCRIPTION DATE BY B UPDATED //00 BJF D D C OPTION, SEE NOTE # ITEM 0 PARTS FOR.CAC0 " CARTRIDGE Parts List QTY PART NUMBER DESCRIPTION CAC000 KNIFE ARM CAC000 KNIFE GUARD PIVOT PIN CAC000 KNIFE GUARD BSG0 BUSHING, mm CAC0000 BUSHING CAC000 TAB ADJUSTER CAC000 PIN SPR0 SPRING CAC000 PIN PLATE PSCB0 KNIFE BLADE " SPR0 EXTENSION SPRING FBHMD00P0 BUTT. HD. M X FFHME00P0 FL. HD. CAP SCREW M X FSSME00P0 CUP POINT SET SCREW M X CAC000 KNIFE GUARD CUSHION CAC000 BRONZE BUSHING SPR0 TORSION SPRING C 0 PARTS FOR.CAC " CARTRIDGE B PRELOAD, SEE NOTE # ITEM 0 QTY Parts List PART NUMBER DESCRIPTION CAC000/ KNIFE ARM CAC000/ KNIFE GUARD PIVOT PIN CAC000/ KNIFE GUARD BSG0 BUSHING, mm CAC0000 BUSHING CAC000 TAB ADJUSTER CAC000 PIN SPR0 SPRING CAC000/ PIN PLATE PSA0 KNIFE BLADE " SPR0 EXTENSION SPRING FBHMD00P0 BUTT. HD. M X FFHME00P0 FL. HD. CAP SCREW M X FSSME00P0 CUP POINT SET SCREW M X CAC000/ KNIFE GUARD CUSHION CAC000 BRONZE BUSHING SPR0 TORSION SPRING B SPECIAL NOTES: A ) ITEM #, TORSION SPRING, MUST BE PRELOADED ONE FULL TURN TO GET THE APPROPIATE TENSION. IT MUST BE WOUND IN THE DIRECITION IT'S WRAPPED IN TO FUNCTION CORRECTLY. ) OPTIONAL SPRING FOR PROCESSING VOID BOXES: LOVESHAW # SPR0LD. (LIGHT DUTY SPRING IS RED IN COLOR FOR EASY VISUAL IDENTIFICATION). MAT'L C.R.S. PART # STD CAD FILE KAACAC0 PLOT DATE //00 ST. ST. DRAWN DATE //00 STAINLESS : NO FINISH DO NOT SCALE PRINT THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. TOLERANCES UNLESS OTHERWISE NOTED:.X = +.00 TITLE INCH.XX = +.0 ANGLES + /.XXX = +.00.X = +.0mm MACH. METRIC.XX = +.mm DWG NO FINISH.XXX = +.mm MATERIAL FRACTIONS + / DRAWN LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. KNIFE ASSEMBLY.CAC0/.KAACAC0/ AMYR SCALE CHECKED APPROVED A

79 REVISION HISTORY REV DESCRIPTION DATE BY A RELEASED //00 AMYR D D PARTS FOR.CAC0 " CARTRIDGE C ITEM 0 QTY Parts List PART NUMBER DESCRIPTION PSC BRAKE WASHER CAC00A SHAFT, TAPE CORE THREADED PSC TAPE CORE NUT CAC00 HEX LOCK NUT CAC000 TAPE CORE " PSCB SPRING COMPRESSION PSC SPRING DISC SPH PAN HD. SCREW M X CAC000 COLLAR, TAPE CORE CAC000 TAPE CORE NUT FSHMF00B0 SOC. HD. CAP SCREW M X 0 CAC0000 RETAINING CLIP W/ LOCK CAC000 KEY STOP CAC000 SPRING SLEEVE FBHMD00P0 BUTT. HD. M X C B 0 ITEM 0 PARTS FOR.CAC " CARTRIDGE Parts List QTY PART NUMBER DESCRIPTION PSC BRAKE WASHER CAC00A SHAFT, TAPE CORE THREADED LP0B0 TAPE CORE NUT CAC00 HEX LOCK NUT CAC000/ TAPE CORE " PSCB SPRING COMPRESSION PSC SPRING DISC SPH0 PAN HD. SCREW M X 0 CAC000 COLLAR, TAPE CORE CAC000 TAPE CORE NUT FSHMF00B0 SOC. HD. CAP SCREW M X 0 CAC0000 RETAINING CLIP W/ LOCK CAC000 KEY STOP CAC000 SPRING SLEEVE FBHMD00P0 BUTT. HD. M X B A MAT'L C.R.S. PART # STD CAD FILE.TCAAMY PLOT DATE //00 ST. ST. DRAWN DATE //00 STAINLESS : NO FINISH DO NOT SCALE PRINT THIS DRAWING AND SUBJECT MATTER THEREON IS THE EXCLUSIVE PROPERTY OF LOVESHAWITW AND IS TO BE TREATED BY YOU AS CONFIDENTIAL PRPRIETARY INFORMATION. THIS DRAWING OR SUBJECT MATTER THEROF SHALL NOT BE REPRODUCED OTHER THAN FOR YOUR OWN USE OR TO BE DISCLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN CONSENT OF LOVESHAWITW AND WILL BE RETURNED TO LOVESHAWITW UPON REQUEST. TOLERANCES UNLESS OTHERWISE NOTED:.X = +.00 TITLE INCH.XX = +.0 ANGLES + /~.XXX = +.00.X = +.0mm MACH. METRIC.XX = +.mm DWG NO FINISH.XXX = +.mm MATERIAL FRACTIONS + / DRAWN LOVESHAW an ITW Company RT., SOUTH CANAAN, PA. TAPE CORE ASSEMBLY.TCA/ AMYR SCALE CHECKED APPROVED A

80 CAC0 INCH RECOMMENDED SPARE PARTS KIT FOR CAC0 SIDE THREAD CARTRIDGE KIT PART #.REPKITCAC0 PART # QTY DESCRIPTION CAC0000 ROLLER PSCB0 KNIFE BLADE " SPR0 SPRING EXTRUSION SPR0 COMPRESSION SPRING SPR0 EXTENSION SPRING X0RPS/R SPRING, TORSION REWORKED PSC0 MAIN SPRING CARTRIDGE.TRA0 TENSION ROLLER ASSEMBLY PSC BRAKE WASHER CAC000 STOP, KNIFE ARM BSG00 PLASTIC FLANGE BUSHING CAC0000 BUSHING BSG0 BUSHING SPH SNAP RING, EXTERNAL SPH RETAINING RING, EXTERNAL SPR0 EXTENSION SPRING SPH BUMPER CAC000 SHAFT CAP CAC000 KNIFE GUARD CUSHION SPR0 COMPRESSION SPRING CAC000 PIN CAC000 PIN PLATE BSG0 FLANGE BUSHING SPR0 EXTENSION SPRING

81 CAC INCH RECOMMENDED SPARE PARTS KIT FOR CAC SIDE THREAD CARTRIDGE KIT PART #.REPKITCAC PART # QTY DESCRIPTION CAC0000/ ROLLER PSCA0 KNIFE BLADE " SPR0 SPRING EXTRUSION SPR0 COMPRESSION SPRING SPR0 EXTENSION SPRING X0RPS/R SPRING, TORSION REWORKED PSC0 MAIN SPRING CARTRIDGE.TRA TENSION ROLLER ASSEMBLY PSC BRAKE WASHER CAC000 STOP, KNIFE ARM BSG00 PLASTIC FLANGE BUSHING CAC0000 BUSHING BSG0 BUSHING SPH SNAP RING, EXTERNAL SPH RETAINING RING, EXTERNAL SPR0 EXTENSION SPRING SPH BUMPER CAC000 SHAFT CAP CAC000/ KNIFE GUARD CUSHION SPR0 COMPRESSION SPRING CAC000 PIN CAC000/ PIN PLATE BSG0 FLANGE BUSHING SPR0 EXTENSION SPRING