FaceClipper Model # Serial #

Size: px
Start display at page:

Download "FaceClipper Model # Serial #"

Transcription

1 FaceClipper 000 Model # Serial # Vertex Fasteners A Subsidiary of Leggett & Platt, Inc. 798 Sherwin Avenue Des Plaines, Illinois 6008 U.S.A. (87) REV. O

2 Table of Contents OF EQUIPMENT... OPERATION INSTRUCTIONS... Loading a Coil of FaceClips... Removing FaceClips from Tool Assembly... Adjusting Clip Trigger Assembly... Adjusting End Stop... SAFETY INSTRUCTIONS... 5 MAINTENANCE... 5 Recommended Spare Parts List... 6 TROUBLESHOOTING INFORMATION... 7 FIGURE... 8 FIGURE... 8 Specifications... 9 DRAWINGS TOOL ASSEMBLY (VC0)... 0 FACECLIPPER 000 (VC6)... REV. O

3 OF EQUIPMENT The FaceClipper 000 is a specially designed machine used by upholstered furniture manufacturers to quickly and accurately install patented FaceClips into wooden frame rails. This all pneumatic machine accommodates rails from 5/8 to / thick and up to 9 long. In addition, curved rails and one-piece front panels are easily handled with the FaceClipper 000. The straightforward, innovative design elements have resulted in a productive and versatile machine for all manufacturers. The FaceClipper 000 is made up of five main components:. Turntable Assembly a. Each turntable holds a coil of FaceClips each containing 65 pieces.. Tool Assembly (Clipping Head) a. The Tool Assembly installs FaceClips into wooden furniture rails.. Clip Trigger Assembly a. The Clip Trigger Assembly is adjustable giving the operator a center-to-center clip range of to 8.. End Stop a. The End Stop, used to install the first clip, is operator adjustable and can accommodate rails from 0 to 9 long. 5. Pneumatic Control Circuit OPERATION INSTRUCTIONS Loading a Coil of FaceClips. Place coil on hub of Turntable Assembly (VC09).. Place Disk Cap Assembly (VC07) on top of coil. Run clips off coil, onto Platform (VC060) and down rail toward tool.. Lift Feed Cylinder (VC006), swing flag forward to support cylinder. 5. Feed clips into Tool. 6. From the front of tool, slide the Loading Tool Hook (VC096); hook down, through slot in Front Plate (VC0), pull clips forward. 7. Verify that Feed Cylinder is down. REV O

4 Removing FaceClips from Tool Assembly. Lift Feed Cylinder (VC006) up, swing flag forward to support cylinder.. Spread Pawl (VC0) away from side plates while removing clips from rear. Caution: Do not overspread pawl. Adjusting Clip Trigger Assembly. Loosen hand knob.. Slide assembly to desired location. (Align pointer with scale.). Tighten knob to lock Clip Trigger in place. Adjusting End Stop. Loosen hand knob.. Slide assembly to desired location. (Align pointer with tape measure.). Tighten knob to lock End Stop in place. Set air pressure between psi for proper operation of the FaceClipper 000. Hardness of wood will determine setting. After required adjustments have been made and the clips have been loaded you may begin production. To install the first clip:. Lay rail on FaceClipper.. Push rail back against entry guide.. Slide rail against End Stop, press knee switch for placement of first clip. Once the first clip has been placed, slide the rail away from the End Stop toward the Clip Trigger. The FaceClipper will then install clips the length of the rail according to the spacing that you have set. To insure accuracy, use a consistent speed while running the rail through the machine. REV O

5 SAFETY INSTRUCTIONS. Operators should ALWAYS wear safety glasses while operating, maintaining or repairing the equipment.. NEVER place hands or fingers near clip exit area when operating tool or when connecting air supply to machine.. Always shut off air supply when servicing tool. MAINTENANCE Recommended Daily Maintenance. Using supplied air gun; blow off woodchips and debris from Tool and Trigger assembly.. Add - drops of 0-weight oil to opening between front plate and top of blade of Tool assembly. The Trigger assembly should be checked for ease of movement. Lightly lubricate if necessary. Recommended Weekly Maintenance Drain Reservoir Tank for condensation. Recommended Monthly Maintenance Remove front plate from tool and lubricate driver blade and front plate. REV O 5

6 FACECLIPPER 000 RECOMMENDED SPARE PARTS LIST Y VC00 AIR LUBE OIL VC0 PAWL VC0 PAWL SPRING VC06 PISTON FEED SPRING VC57 TORSION SPRING VC5 PIN, FEED CYLINDER VH000 O RING, # VH0069 PUSH-IN FTG 90 DEG VH05 O RING, #0 VH08 SWITCH, KNEE VH05 HAIR PIN

7 TROUBLESHOOTING INFORMATION PROBLEM CAUSE SOLUTION Blade does not return. Obstruction in tool. Cylinder Spring damaged. Remove obstruction. Replace Spring (VC06). Clips not feeding. Dispenser obstruction. Feed cylinder not engaged. Remove obstruction. Engage by lifting up cylinder allowing flag to Clip not seated against rail (Fig. ). Clip s hook is overhanging edge of rail (Fig ). Incorrect clip spacing. Clip driven too far into rail. Missed clip. Low air pressure. Incorrect Flow Control Valve setting. Incorrect tool height. The board is warped. Rail is not against entry guides. Clip Trigger is set inaccurately. Air pressure too high. Incorrect Flow Control Valve setting. Clips ran out. Valve (VH087) is closed. drop. Increase pressure. (Never exceed 90 psi) Turn Flow Control Valve Clockwise. Lower tool. Operator must run rail against entry guides. Reset Clip Trigger to correct location. Reduce air pressure. Turn Flow Control Valve Counterclockwise. Reload with new coil. Line up rail for correct clip placement. Press button on valve to fire matching tool. Turn lever to vertical position. REV O 7

8

9 Specifications Air: psi, 6 cfm Machine Size: Depth: Footprint = 58.5, Overall 58.5 Width: Footprint = 8, Overall 6.5 Height: 65 Weight: 50 lbs Rail Dimensions: Thickness: 5/8 Length: Consult factory Clip Coil Capacity: 65 FaceClips REV O 9

10 VH06 VC00 VC0 VC085 VC07 VC0 VH05 VH079 INSTALL WITH LOCTITE 7 VC0 VC05 VC06 VH06 VC5 VH06 VC0 VH07 VC00 VC085 VH0 VC099 VC0 VC0 VH00 VH06 VC0 VH060 VH0050 VC57 VH08 VC078 VH05 VC00 VC00 VC006 VC0 VC0 VC0 VC0 VC0 VC0 VC0 VC05 VC06 VC07 VC08 VC09 VC078 VC085 VC087 VC099 VC0 VC5 VC57 VC5 VH00 VH0050 VH08 VH0 VH06 VH07 VH05 VH079 VH06 VH05 VH05 VH060 VH06 VH06 VH06 VH065 VH0776 VH0779 WARNING LABEL CLIP FEEDER STOP CLIP FEEDER ASSEMBLY PAWL BALL BEARINGS SPRING PAWL SPRING LEFT-HAND SIDE PLATE RIGHT-HAND SIDE PLATE CYLINDER MOUNT FRONT PLATE BLADE BLADE GUIDE GUARD FEEDER BRACKET COVER RAIL 000 SPRING RESTRICTOR SPACER, / x /8, / FACECLIPPER LABEL TOOL MOUNT K/K TOOL RAIL SHIM - K, K & K TORSION SPRING PIN, FEED CYLINDER SHCS, 8 - x / FLOW CONTROL SHCS, 0 - x 5/8 SHCS, 8 - x /8 SHCS, 5/6 - x / NUT, NYLOCK, 5/6 - SET SCREW, 5/6-8 x /8 CYLINDER HOSE BARB, / x /8 NPT /8 CHROME BALL HAIR PIN SHCS, /8 - x / HHCS, 5/6-8 x / NUT, JAM, 5/6-8, GR5 BHCS, 8 - x / SHCS, / - 0 x / PIN, ROLL, /8 x / NUT, NYLOCK, /8 - A VH0 VH06 VC08 VC0 VC006 VC00 VC09 VC0 VC5 VH05 VH0776 VC087 VH06 VC00 VH0779 VH065 VC00 VH005 VC505 VC06 VH05 THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED, OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VERTEX FASTENERS. VH000 VC006 VC006 - FEED CYLINDER ASSEMBLY VC00 CYLINDER BODY (CLIP FEEDER) VC00 PISTON (CLIP FEEDER) VC06 CLIP FEEDER SPRING VC505 CYLINDER END CAP (CLIP FEEDER) VH000 O-RING, # VH005 SHCS, 0 - x / VH05 O-RING, #0 REV ECN BY APPD DATE MATERIAL: A 96 - VH069 & VH0779 WAS HEX JMW MR HEAT TREATMENT: FINISH: TOL. UNLESS SPECIFIED INCHES.X =.00.XX =.05.XXX =.005 ANGLES / INVENTOR C 009 DWN BY JMW APPD MR DATE --09 SCALE : DWG. NO. VC0 VERTEX FASTENERS 7 JARVIS AVENUE SKOKIE, IL U.S.A. FACECLIPPER K/K TOOL ASSEMBLY C

11 R058 VC09 VC060 VC06 VC07 VC07 VC08 VC0 VC0 VC05 VC06 VC09 VC0 VC50 VC505 VC508 VC50 VC5 VC5 VC59 VC5 VC50 VC56 VC56 VC568 VC577 VH00 VH0060 VH006 VH0067 VH008 VH00 VH0 VH0 VH0 VH080 VH08 VH088 VH09 VH09 VH06 VH0 VH0 VH08 VH06 x VH06 x 6 VH050 x VH050 x 50 VH060 VH0 VH0 VH050 VH086 VH000 VH08 VH05 x 6 VH05 x 0 VH0 VH050 VH06 VH06 VH065 VH065 TANK TURNTABLE ASSEMBLY PLATFORM PLATFORM RAIL BASE ANGLE IRON COVER DISK CAP ASSEMBLY CLIP DISK GUARD FACECLIP CLIP TRIGGER ASSY FACECLIP K/K TOOL ASSEMBLY FC K/K CLIP DISPENSER FRAME CLIPPING HEAD FIXED HEIGHT DETAIL LEG ASSY W/ TANK MNTG BRKT CONTROL VALVE DETAIL - ASSYS FRONT RAIL LEG ASSEMBLY STRUT CENTER RAIL REAR RAIL ENTRY GUIDE RAIL ENTRY GUIDE RAIL STUD VC NAMEPLATE EXIT CONVEYOR DETAIL KNEE KNOCKER ASSEMBLY UNI-STRUT RAIL TAPE MEASURE END STOP - SIMPLE BHCS, 0 - x / SHCS, 5/6-8 x / NUT, 5/6-8 CAP WASHER, LOCK, 0 WASHER, LOCK, 5/6 SHCS, 0 - x / SHCS, 0 - x / SHCS, 0 - x SKATE WHEEL ROLLER FHCS, /8-6 x 7/8 SHCS, / - 0 x / SPACER / OD / ID LONG NUT, NYLOCK, 0 - WASHER, SAE, / WASHER, FENDER #8 DRIVE SCREW TUBING, / OD POLYETHYLENE, BLK TUBING, / OD POLYETHYLENE, BLK DUAL TUBING, / OD, BLK & CLR DUAL TUBING, / OD, BLK & CLR WASHER, LOCK, / NUT, HEX, / - 0 SHCS, 5/6-8 x BUSHING, HEX REDUCER, / x / SAFETY VALVE SHCS, / - 0 x / PLUG, / NPT HOSE, / ID, BLUE HOSE, / ID, BLUE BUSHING, HEX REDUCER, / x / SHCS, / - 0 x SHCS, /8-6 x / DRILL BUSHING SPACER, / OD x /8, #0 SPACER, / OD x /, # VH0060 VH006 VH00 VH08 VC50 VC5 VH006 VH00 VH05 x 0 VH05 x 6 VC0 VH06 x VC50 VH050 x VH0 VC06 VC09 VC56 VH06 x 6 R058 VC0 VH09 VH09 VC5 VC59 VC5 VH08 VH088 VC5 VH050 x 50 VC50 VH08 VC0 VH050 VH060 VH008 VC060 VH0 VC06 VH0 VH008 VC07 VH0 VH06 VH08 VH06 VH065 VH0 VH065 VH050 VH086 VC577 VH080 VH006 VH00 VH0060 VC505 VC07 VC09 VC08 VH06 VH0067 VH0 VC05 VH000 VH0 VH00 VH0 VC568 VC56 VH06 VH0060 VC50 VH0060 VH00 VC508 THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED, OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VERTEX FASTENERS. VC505 VC50 - EXIT CONVEYOR DETAIL VC505 LEG ASSEMBLY VC50 EXIT CONVEYOR VC5 BRACKET VH0060 SHCS, 5/6-8 x / VH006 NUT, 5/6-8 VH00 WASHER, LOCK, 5/6 VH08 ROLLER REV ECN BY APPD DATE MATERIAL: HEAT TREATMENT: FINISH: TOL. UNLESS SPECIFIED INCHES.X = `.00.XX = `.05.XXX = `.005 ANGLES `/~ INVENTOR C 009 DWN BY JMW APPD MR DATE --09 SCALE :8 DWG. NO. VC6 VERTEX FASTENERS 7 JARVIS AVENUE SKOKIE, IL U.S.A. FACECLIPPER FIXED HEIGHT PAGE OF D

12 VH050 VC5 VH05 VC55 VC507 VH05 VH066 VC5 VC TOP VC07 VH0 VH00 VH0069 VC55 RAIL # VC EACH SIDE SHCS TOP BOTTOM 5/8 0 VH059 (" LENGTH) / VH059 7/8 0 VH059 VH087 ( /" LENGTH) VC06 - CLIPPING HEAD FIXED HEIGHT DETAIL SCHS SHCS, 5/8 - x? VC07 BASE HEIGHT SPACER VC08 FIXED HEIGHT WASHER VC SPACER SHIM X VC50 SUB-PLATE VC507 FIXED PLATE VC5 BASE PLATE VC55 SPACER VC5 SCALE VH00 BHCS, 0 - x / VH066 NUT, ACORN, 5/8 - VH097 FHCS, 5/6-8 x.5 VC577 - END STOP - SIMPLE VH0 KNOB VH05 Z-BRACKET VH05 NUT, STUD, / - VH08 VH00 THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED, OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VERTEX FASTENERS. VC5 VH05 VC5 VC56 - KNEE KNOCKER ASSEMBLY VC5 KNEE KNOCKER VC5 HINGE BRKT W/ SWITCH VC5 HINGE BRACKET VC55 MOUNT BLOCK VH00 SHCS, 0 - x VH0069 PUSH-IN FTG, VH00 WASHER, LOCK, 5/6 VH0 SHCS, 5/6-8 x VH08 SWITCH VH05 SPRING, DIE, / x VH05 SHCS, /8-6 x / VH050 SHCS, / - 0 x VC5 VH097 VH00 VC50 VC BOTTOM VC08 SCHS VH0 VH05 VH0079 VH0079 VH0 VH00 VH005 VH06 VH005 VH005 VH09 VC05 VC07 VH0 VH09 VC050 PRESS FIT VC07 - DISK CAP ASSEMBLY DISK CAP DISK CAP HUB MAGNET BHCS, 0 - x / VC07 VC09 - TURNTABLE ASSEMBLY VC07 HUB VC08 SPOKE VC050 SPINDLE VH00 VH0 VH000 VH07 VH0069 VH07 VH06 VH0079 VH07 VH006 VC05 VH0 VC07 VC08 ALUMINUM 606 WELD - SIDES ONLY - VH06 VC075 VH050 VH07 6 VH0 VH005 VH086 VH0 VH09 VH06 VH0050 VH069 VH000 VH00 VC006 - FEED CYLINDER ASSEMBLY VC00 CYLINDER BODY VC00 PISTON VC06 CLIP FEEDER SPRING VC505 CYLINDER END CAP VH000 O-RING, # VH005 SHCS, 0 - x / VH05 O-RING, #0 VC505 VC085 VH06 VC00 VC0 VC00 VC06 VH05 VC00 VH05 VC07 VH000 VH0779 VH05 INSTALL WITH LOCTITE 7 VC0 - CONTROL VALVE DETAIL VC075 Y FITTING VH0050 FLOW CONTROL VH0069 PUSH-IN FTG, 90 / OD x /8 NPT VH06 HEX REDUCER BUSHING, / x /8 VH09 BRASS FTG, 90, / x /8 NPT VH005 NIPPLE, / NPT x VH06 TEE, REDUCER, / x / x / VH06 HOSE BARB, / x /8 NPT VH0 BUSHING, HEX REDUCER, / x / VH069 VALVE VH07 SHUTTLE VALVE VH07 NIPPLE /8 VH050 MUFFLER, / NPT VC0 - CONTROL VALVE DETAIL VH000 RETRACTABLE HOSE VH00 ELBOW, BRASS STREET, / NPT VH006 PLUG, MALE, / - / VH0079 BUSHING, HEX REDUCER, /8 x / VH000 BUSHING, HEX REDUCER, / x /8 VH06 FILTER/REGULATOR W/ GAUGE VH07 VALVE, VENTED SHUT-OFF BALL VH07 AIR GUN VH00 PUSH-IN FTG, 90 / OD x / NPT VH00 NIPPLE, /8 NPT VH0 TEE, /8 VH086 NIPPLE, /8 NPT x VH069 VH079 VC0 VC0 VC0 VC05 VC06 VC58 VH06 VH06 VC55 VH005 VC505 VC5 VH06 VH0 VC5 VH007 VH009 VC57 VH06 VC0 VC0 VH000 VH07 VC00 VC50 VH08 VC5 VC5 VC50 VC5 VC50 VC099 VC006 VH005 VC50 VC VC VC56 VC078 VC00 VH0 VC5 VH05 VH0069 VC085 VH0 VH0050 VH06 VH0776 VC087 VC0 VH060 VH07 VC500 VC57 REV ECN BY APPD DATE MATERIAL: HEAT TREATMENT: FINISH: VH0 VC0 VH06 VH06 VC0 VH00 VH05 VH065 VC08 VC09 VC VC VC500 VC50 VC50 VC50 VC505 VC5 VC5 VC5 VC55 VC56 VC57 VC50 VC5 VC58 VH009 VH007 VH000 VH005 VH0069 VH0 VH05 VH06 VH07 VH06 VH0 VH0 TOL. UNLESS SPECIFIED INCHES.X = `.00.XX = `.05.XXX = `.005 ANGLES `/~ INVENTOR VC0 - FACECLIP K/K TOOL ASSY VC00 WARNING LABEL VC00 CLIP FEEDER STOP VC006 CLIP FEEDER ASSEMBLY VC0 PAWL VC0 BALL BEARINGS SPRING VC0 PAWL SPRING VC0 LEFT-HAND SIDE PLATE VC0 RIGHT-HAND SIDE PLATE VC0 CYLINDER MOUNT VC0 FRONT PLATE VC05 BLADE VC06 BLADE GUIDE VC07 GUARD VC08 FEEDER BRACKET VC09 COVER VC078 RAIL 000 VC085 SPRING RESTRICTOR VC087 SPACER, / x /8, / VC099 FACECLIPPER LABEL VC0 TOOL MOUNT K/K VC5 TOOL RAIL SHIM - K, K & K VC57 TORSION SPRING VC5 PIN, FEED CYLINDER VH00 SHCS, 8 - x / VH0050 FLOW CONTROL VH08 SHCS, 0 - x 5/8 VH0 SHCS, 8 - x /8 VH06 SHCS, 5/6 - x / VH07 NUT, NYLOCK, 5/6 - VH05 SET SCREW, 5/6-8 x /8 VH079 CYLINDER VH06 HOSE BARB, / x /8 NPT VH05 /8 CHROME BALL VH05 HAIR PIN VH060 SHCS, /8 - x / VH06 HHCS, 5/6-8 x / VH06 NUT, JAM, 5/6-8 VH06 BHCS, 8 - x / VH065 SHCS, / - 0 x / VH069 WASHER, /8 VH0776 PIN, ROLL, /8 x / VH0779 NUT, HEX, /8 - RAIL # VC SHCS 5/8 0 VH06 ( /" LENGTH) / VH06 7/8 VH088 (" LENGTH) VH088 VC0 - FACECLIP CLIP TRIGGER ASSY RISER - BASE HEIGHT RISER SHIM - CYLINDER END CAP TRIGGER PISTON MOUNTING PLATE SPRING SPRING CYLINDER BODY SPACER BUSHING MANIFOLD SPACER POINTER AIR VALVE, CARTRIDGE CYLINDER SPACER RAIL GUIDE O-RING, # - PUSH-IN FTG, / x /8 NPT / - x T-BOLT SHCS, 0 - x / PUSH-IN FTG, 90, / x /8 NPT KNOB O-RING, #0 - SHCS, 0 - x / SHCS, 5/6 - x / SHCS, / - 0 x / SET SCREW, 0 - x / SHCS, 5/6 - x / C 009 VERTEX FASTENERS 7 JARVIS AVENUE DWN BY JMW SKOKIE, IL U.S.A. APPD MR FACECLIPPER FIXED DATE --09 HEIGHT SCALE DWG. NO. VC6 PAGE OF D

FaceClipper Model # Serial #

FaceClipper Model # Serial # FaceClipper 000 Model # Serial # Vertex Fasteners A Subsidiary of Leggett & Platt, Inc. 798 Sherwin Avenue Des Plaines, Illinois 6008 U.S.A. (87) 768-639 REV. O -7-5 Table of Contents DESCRIPTION OF EQUIPMENT...

More information

FaceClipper Model # Serial #

FaceClipper Model # Serial # FaceClipper 000 Model # Serial # Vertex Fasteners A Subsidiary of Leggett & Platt, Inc. 7 Jarvis Avenue Skokie, Illinois 60076 U.S.A. (87) 9-80 Table of Contents OF EQUIPMENT... OPERATING INSTRUCTIONS...

More information

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES

Eclipser 2500/2800 OPERATING MANUAL. and Continuous Coil (CC) Clipping System. ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Eclipser 2500/2800 and Continuous Coil (CC) Clipping System Encore Eclipser 2500 Series (Green) Hartco Eclipser 2500 (Black) not shown OPERATING MANUAL ENCORE (EA) ECLIPSER 2500 and 2800 SERIES Pneumatic

More information

Opera ons & Parts Manual VersaClipper 3100

Opera ons & Parts Manual VersaClipper 3100 Opera ons & Parts Manual VersaClipper 3100 Heavy Duty Servo Driven & Computer Controlled Fully Automa c and Highly Versa le Clip A aching Machine Model #3100 Serial # 1 Revised 09/21/17 Table of Contents

More information

RC-200EX / RC-150EX Rim Clamp Tire Changer

RC-200EX / RC-150EX Rim Clamp Tire Changer RC-200EX / RC-150EX Rim Clamp Tire Changer For servicing motorcycle and ATV tire/wheel assemblies as well as automotive and most light truck tire/wheel assemblies (holds 6 to 8-inch wheels for manual tire

More information

Page 1 of 19. Part# /10/2006

Page 1 of 19. Part# /10/2006 Part# 1002733-01 10/10/2006 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS

More information

MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO & UP

MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO & UP MODEL NO. -900 & UP MODEL NO. 00-900 & UP MODEL NO. 0-900 & UP MODEL NO. 0-900 & UP SKID SPRAYER FORM NO. 99-055 REV. B SET-UP AND PARTS LIST Refer to the illustrated Parts List for the details of parts

More information

Parts Manual for the Wright Z

Parts Manual for the Wright Z Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 6/2010 Shown with OPTIONAL Grass Collection System 2010 Wright Manufacturing Inc., All Rights

More information

9010 A/E. Rim Clamp Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies

9010 A/E. Rim Clamp Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies 9010 A/E Rim Clamp Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies s Identification READ these instructions before placing unit in service KEEP these and other

More information

Parts Manual Zero Turn Mower / Z 248F

Parts Manual Zero Turn Mower / Z 248F Parts Manual Zero Turn Mower / Z 248F 967262501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support

More information

Parts Manual for the Wright Z

Parts Manual for the Wright Z Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 9/2007 Shown with OPTIONAL Grass Collection System 2006 Wright Manufacturing Inc., All Rights

More information

Parts Manual Rev. A

Parts Manual Rev. A 115 97 79-27 Rev. A Parts Manual Z 248F / 967 844801-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

Parts Manual Rev. A

Parts Manual Rev. A 115 96 28-27 Rev. A Parts Manual Z 242F / 967 271802-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

Magnesium Option, Late Model Front Seal, Viton, P/N 67256V Rear Seal, Viton, P/N 67257V Shifter Installed Heat Treated Yoke, P/N

Magnesium Option, Late Model Front Seal, Viton, P/N 67256V Rear Seal, Viton, P/N 67257V Shifter Installed Heat Treated Yoke, P/N DESCRIPTION OPTION Magnesium Option, Late Model 80100L Front Seal, Viton, P/N 67256V 80109 Rear Seal, Viton, P/N 67257V 80110L Shifter Installed 80112L Heat Treated Yoke, P/N 62946-6 80119-6 Heat Treated

More information

Parts Manual Rev. A

Parts Manual Rev. A 115 97 25-27 Rev. A Parts Manual Z 242F / 967 844702-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

BASELINE. Rim Clamp Tire Changers. Parts Identi cation. For servicing single piece automotive and most light truck tire/wheel assemblies.

BASELINE. Rim Clamp Tire Changers. Parts Identi cation. For servicing single piece automotive and most light truck tire/wheel assemblies. BASELNE Rim Clamp Tire Changers For servicing single piece automotive and most light truck tire/wheel assemblies. Model 300 Shown Model 500 Shown Parts denti cation READ these instructions before placing

More information

Parts Manual Rev. A RZT48 /

Parts Manual Rev. A RZT48 / 115 91 36-2 Rev. A Parts Manual RZT48 / 96 62001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of 10%

More information

GTS50, GTS60, and GTS70 Rim Clamp Tire Changers

GTS50, GTS60, and GTS70 Rim Clamp Tire Changers GTS50, GTS60, and GTS70 Rim Clamp Tire Changers For servicing single piece automotive and most tubeless light truck tire/wheel assemblies. Any other type, including tube type and agricultural, require

More information

PARTS LIST. BRC Racing BRC 250 FE SERIAL NO: BRC Racing

PARTS LIST. BRC Racing BRC 250 FE SERIAL NO: BRC Racing BRC Racing PARTS LIST BRC 20 FE SERIAL NO: BRC Racing A Division of BRC Engineering Ltd. # - 2nd Ave NE Calgary, Alberta Canada T2E S1 Tel: 0-21-00 Fax: 0-21-0 Web: www.brceng.com RELEASE DATE: 01-200

More information

RC-100. Parts Identification

RC-100. Parts Identification RC-100 Rim Clamp Tire Changer For servicing motorcycle and ATV tire/wheel assemblies, also single piece automotive and most light truck tire/wheel assemblies s Identification READ these instructions before

More information

Parts Manual Rev. B RZT48 /

Parts Manual Rev. B RZT48 / 115 91 36-2 Rev. B Parts Manual RZT48 / 96 62001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of 10%

More information

Parts Manual Rev. A Z 246 /

Parts Manual Rev. A Z 246 / 115 97 16-27 Rev. A Parts Manual Z 246 / 967 844501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

304 PARTS MADE IN THE USA natvac.com. Exclusive Manufacturer

304 PARTS MADE IN THE USA natvac.com. Exclusive Manufacturer 304 PARTS M I N I C A T A L O G IN THE USA 800-253-5500 natvac.com 304 Repair Kits FEATURES Comes with or without bearings and includes the seals, gaskets, and vanes. Designed, built, and supported in

More information

Parts List for all Sentar Sport models For Sentar Sport serial #33615 and higher until superseded

Parts List for all Sentar Sport models For Sentar Sport serial #33615 and higher until superseded Parts List for all Sentar Sport models For Sentar Sport serial #33615 and higher until superseded WRIGHT MANUFACTURING, INC. - 4600X WEDGEWOOD BLVD - FREDERICK, MD 21703 Revised 01/2007 36" CUTTER DECK

More information

WSL-Series. WSL- Series

WSL-Series. WSL- Series WSL-Series WSL- Series Click the appropriate link below for the major component of the liftgate for which you are trying to find the correct part. If you are unsure of the name of the part in Waltco terminology,

More information

Hydrostatic Zero-Turn Commercial Riding Mower

Hydrostatic Zero-Turn Commercial Riding Mower Hydrostatic Zero-Turn Commercial Riding Mower Professional Turf Equipment 54" Fabricated Deck ILLUSTRATED PARTS LIST TABLE OF CONTENTS Frame Assembly.................................. 3 54" Fabricated

More information

Parts Manual Zero Turn Mower / Z

Parts Manual Zero Turn Mower / Z Parts Manual Zero Turn Mower / Z 246 967271501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support

More information

INSTRUCTION, GPT HAND PUMP KIT INSTALLATION GPT KIT P/N

INSTRUCTION, GPT HAND PUMP KIT INSTALLATION GPT KIT P/N LIFT CORPORATION Sht. 1 of 28 DSG# M-09-16 Rev. B Date: 4/22/2014 INSTRUCTION, GPT HAND PUMP KIT INSTALLATION GPT KIT P/N 283330-01 NEEDLE VALVE, ADJUSTABLE, SAE #6 P/N 906739-01 QTY. 1 CONNECTOR, SAE

More information

5035 A/E. Rim Clamp Tire Changer. Parts Identification

5035 A/E. Rim Clamp Tire Changer. Parts Identification 5035 A/E Rim Clamp Tire Changer Parts Identification READ these instructions before placing unit in service KEEP these and other materials delivered with the unit in a binder near the machine for ease

More information

MID RISE. INSTALLATION and OPERATION MANUAL MODEL 6000A // 6000E 6,000 LB. CAPACITY. READ and SAVE THIS INSTRUCTION MANUAL

MID RISE. INSTALLATION and OPERATION MANUAL MODEL 6000A // 6000E 6,000 LB. CAPACITY. READ and SAVE THIS INSTRUCTION MANUAL INSTALLATION and OPERATION MANUAL MID RISE MODEL 6000A // 6000E 6,000 LB. CAPACITY READ and SAVE THIS INSTRUCTION MANUAL AUGUST 2005 6-0944 6500 Millcreek Drive Mississauga, Ontario Canada L5N 2W6 1-800-268-7959

More information

This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown.

This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown. 2525 GARDNER ROAD, BROADVIEW, IL 60155 1.800.323.9114 Outside U.S. 1.708.865.1500 www.tksimplex.com G3 SERIES ELECTRIC POWER PUMP PARTS IDENTIFICATION MANUAL Reference # - 54246 Rev. - A Date - 10/08 This

More information

This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown.

This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown. 2525 GARDNER ROAD, BROADVIEW, IL 60155 1.800.323.9114 Outside U.S. 1.708.865.1500 www.tksimplex.com G5 SERIES ELECTRIC POWER PUMP PARTS IDENTIFICATION MANUAL Reference # - 54247 Rev. - A Date - 10/08 This

More information

4050A. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies

4050A. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies 4050A Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these and other materials

More information

Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers and Higher Until Superseded)

Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers and Higher Until Superseded) Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers 33615 and Higher Until Superseded) Replace with newer revisions as they become available 2007 Wright Manufacturing, Inc. All rights reserved

More information

Parts Manual Rev. 3

Parts Manual Rev. 3 114 08 93-27 Rev. 3 Parts Manual Z 254F / 967954001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

Parts List for The 36 & 42 Wright Stander Mower (For Serial Numbers and Higher Until Superseded)

Parts List for The 36 & 42 Wright Stander Mower (For Serial Numbers and Higher Until Superseded) Parts List for The & Wright Stander Mower (For Serial Numbers 00 and Higher Until Superseded) Replace with newer revisions as they become available 00 Wright Manufacturing, Inc. All rights reserved Revised:

More information

Parts Manual Rev. A RZT54 /

Parts Manual Rev. A RZT54 / 115 93 37-27 Rev. A Parts Manual RZT54 / 967 672101-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of

More information

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800)

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) 272-6276 001-321-757-7611 www.cramarotarps.com Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio, and Canada General Information

More information

MK-5000G exploded VieW

MK-5000G exploded VieW Frame accessories 38 cutting head Pump Assembly 39 connecting linkage foot pedal linkage 40 curtain blade guard 41 ENGINE Assembly 42 PARTS LIST A Frames - - A1 Frame, MK-5000 Main 1 155541 B Pivot Bracket

More information

Parts Manual

Parts Manual 0-- JSE 0 0- Parts Manual Z F / 00-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of % ethanol (E) is

More information

Tech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800)

Tech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800) SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Parts List for: Form No. 108184 RSST-20 Internet

More information

ILLUSTRATED PARTS LIST

ILLUSTRATED PARTS LIST 800-643-7332 amsportworks.com 3171 BLACK WIDOW 136CC FUN KART 136CC FUN KART ILLUSTRATED PARTS LIST TABLE OF CONTENTS SECTION 1 FRAME GROUP WARNING LABELS..................................................................

More information

HYDROBURST HB3038, HB5058, HB80, HB125

HYDROBURST HB3038, HB5058, HB80, HB125 TM HYDROBURST HB3038, HB5058, HB80, HB125 Parts Manual HYDROBURST HB3038, HB5058, HB80 & HB125 s/n Part No. PM1251 INTRODUCTION HOW TO USE THE MANUAL This manual contains illustrations and parts list of

More information

Mitre Band Saw. Installation and Operating Instructions Note: Not all saw parts are shown in this booklet. Replaceable Aluminum Saw Table

Mitre Band Saw. Installation and Operating Instructions Note: Not all saw parts are shown in this booklet. Replaceable Aluminum Saw Table P ARTS C ATALOG 2G PARTS CATALOG Drive Wheel End Pulley Box Speed Reducer M FG. COMPANY, INC. Mitre Band Saw Installation and Operating Instructions Note: Not all saw parts are shown in this booklet Motor

More information

STRIP NAILER. Model NR 90AD (E3) LIST NO. E016 38A 16A 37A 18A 41A 19A 40A 38A 46B 47A 76A 96 46A 75A 24A 23A 48A 68A 50A 32B 51A 32A 52A 53B 53A 54A

STRIP NAILER. Model NR 90AD (E3) LIST NO. E016 38A 16A 37A 18A 41A 19A 40A 38A 46B 47A 76A 96 46A 75A 24A 23A 48A 68A 50A 32B 51A 32A 52A 53B 53A 54A 5A 28A 48A 24A 29A 35A 59A 58A 57A 56A 55A 54A 53A 52A 46B 47A 50A 41A 37A 39 73A 79B 85A 81A 20 44 45 38 49 51A 34A 89A 506 501 505 1 2 3 4 6 7 8 9 10 11 12 13A 14 15 16 17 18 19 20 91 22 23 25 1 27 29

More information

5035 A/E. Rim Clamp Tire Changer. Parts Identification

5035 A/E. Rim Clamp Tire Changer. Parts Identification 5035 A/E Rim Clamp Tire Changer Parts Identification READ these instructions before placing unit in service KEEP these and other materials delivered with the unit in a binder near the machine for ease

More information

JARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner

JARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner 30CL--1 Hock Cutter 30CL--1 Pistol Grip 30CL--3 Dehorner EQUIPMENT SELECTION... Ordering No. 30CL--1 Hock Cutter... 4025013 30CL--1 Hock Cutter with Grabber

More information

RC-100. Rim Clamp Tire Changer. Parts Identification

RC-100. Rim Clamp Tire Changer. Parts Identification RC-100 Rim Clamp Tire Changer For servicing motorcycle and ATV tire/wheel assemblies, also single piece automotive and most light truck tire/wheel assemblies s Identification READ these instructions before

More information

Illustrated Parts List for VMAC System V Ford F250-F350 Triton 5.4 L 3-valve (with 3 bolt crank pulley)

Illustrated Parts List for VMAC System V Ford F250-F350 Triton 5.4 L 3-valve (with 3 bolt crank pulley) Illustrated Parts List for VMAC System V900092 2008 Ford F250-F350 Triton 5.4 L 3-valve (with 3 bolt crank pulley) System V900102 2010-2008 Ford F250-F350 Triton 5.4 L 3-valve (with center bolt crank pulley)

More information

Ride Management System

Ride Management System XR 1800 Ride Management System Parts Identification READ these instructions before placing unit in service KEEP these and other materials delivered with the unit in a binder near the machine for ease of

More information

7060 AX/EX. Rim Clamp Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies

7060 AX/EX. Rim Clamp Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies 7060 AX/EX Rim Clamp Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies READ these instructions before placing unit in service KEEP these and other materials

More information

JOYSTICK STEERING CONTROL & RELATED PARTS (continued)

JOYSTICK STEERING CONTROL & RELATED PARTS (continued) COUNTRY CLIPPER "ZETON BRAT" MOWER REPAIR S MANUAL COUNTRY CLIPPER " ZETON BRAT" ZERO TURN RADIUS MOWER TABLE OF CONTENTS PAGE... CONTENTS SECTION MOWER DECKS AND RELATED S.... " DECK ASSEMBLY.... " DECK

More information

Hydrostatic Zero-Turn Commercial Riding Mower

Hydrostatic Zero-Turn Commercial Riding Mower Hydrostatic Zero-Turn Commercial Riding Mower Professional Turf Equipment 0" Fabricated Deck ILLUSTRATED PARTS LIST TABLE OF CONTENTS Frame Assembly.................................. 3 0" Fabricated Cutter

More information

High Pressure Rotating Arch Parts List Jan. 12, 2017 Rev. A

High Pressure Rotating Arch Parts List Jan. 12, 2017 Rev. A 46-804-00-BK Rotating High Pressure Arch with Turbo Nozzles 46-805-00-BK High Pressure Rotating Arch Rotating High Pressure Arch with V-Jet Nozzles 46-806-00-BK Rotating High Pressure Arch with Wheel Blaster

More information

25 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower

25 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower MMZ 2, 260 2 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower ILLUSTRATED PARTS LIST " Float Cutter Deck - Figure 1 3 1 27 32 17 6 1 11 31 36 3 19 7 23 1 33 38 18 37 22 3 20 2 10 2 12 21 30 39

More information

Parts Manual Zero Turn Mower / Z 254i

Parts Manual Zero Turn Mower / Z 254i Parts Manual Zero Turn Mower / Z 254i 967324201-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support

More information

For servicing single piece automotive and most light truck tire/wheel assemblies

For servicing single piece automotive and most light truck tire/wheel assemblies 7065 AX/EX Rim Clamp Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these

More information

For servicing single piece automotive and most light truck tire/wheel assemblies

For servicing single piece automotive and most light truck tire/wheel assemblies 6065 A/E/AX/EX Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies READ these instructions before placing unit in service KEEP these and other materials delivered

More information

Checked by Revised by

Checked by Revised by Illustrated Parts List for VMAC System V900114 2012-2010 25-3500 DODGE 4X4 Pickup & 3500 Cab & Chassis 6.7L Cummins Diesel System V900116 2012-2011 45-5500 Cab & Chassis 6.7L Cummins Diesel 1. Kit Pack

More information

GTS50/60/70 and GTS90 Rim Clamp Tire Changers

GTS50/60/70 and GTS90 Rim Clamp Tire Changers GTS50/60/70 and GTS90 Rim Clamp Tire Changers For servicing single piece automotive and most tubeless light truck tire/wheel assemblies. Any other type, including tube type and agricultural, require special

More information

Parts Manual Zero Turn Mower / Z

Parts Manual Zero Turn Mower / Z Parts Manual Zero Turn Mower / Z 254 967324101-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support

More information

JARVIS. Model 30CL-ABC Beef Aitch Bone Cutter

JARVIS. Model 30CL-ABC Beef Aitch Bone Cutter Model 30CL-ABC Beef Aitch Bone Cutter EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 30CL--ABC Aitch Bone Cutter Front Entry... 4025102 Rear Entry... 4025111 Hydraulic Power Unit... 4027266

More information

JARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter

JARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner 30CL-1 Hock Cutter with Leg Grabber 30CL-1 Hock Cutter 30CL-3 Dehorner Equipment Selection 30CL-1 Sheep Head Dropper Order Number 30CL-1 Hock Cutter 30CL-1

More information

JARVIS. Model Buster V (CE) Beef Splitting Band Saw

JARVIS. Model Buster V (CE) Beef Splitting Band Saw Model Buster V (CE) Beef Splitting Band Saw EQUIPMENT SELECTION............. Ordering No. TABLE OF CONTENTS......................... Page Buster V Band Saw Shower Head.......... 4006049 Shower Head and

More information

Mulching and Finishing Mowers MP and FP

Mulching and Finishing Mowers MP and FP Mulching and Finishing Mowers MP and FP Parts Manual Locke Turf 0 Highway E, Opp, Alabama, () -00 Transport Wheel, Tire & Spindle MP and FP ALPHABETICAL INDEX CONTENTS PAGE 00 Hydraulic Cylinder (Rear)

More information

37A- S/N 350,000 Up. Turbine Drive Water-Reels. Engine Drive Slurry-Reels T37A E37A. Parts Manual. Serial No. 350, ,999

37A- S/N 350,000 Up. Turbine Drive Water-Reels. Engine Drive Slurry-Reels T37A E37A. Parts Manual. Serial No. 350, ,999 37A- S/N 350,000 Up Turbine Drive Water-Reels Engine Drive Slurry-Reels T37A E37A Parts Manual Serial No. 350,000-359,999 700 S. Schrader Ave. Havana, Illinois 62644 Phone: 309-543-4425 Fax: 309-543-4945

More information

Series. This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown. Pendants - pg.

Series. This illustration is for reference purposes only. The appearance of your unit may differ from the unit shown. Pendants - pg. Power Control Center PENDANT FUNCTION In event multiple buttons are depressed for seconds, the power pump will shutdown. TO RESTART PUMP Press the On button to restart. If problem persists, unplug the

More information

Please read all instructions before operation!!

Please read all instructions before operation!! 1 Flow Rate: 8gpm Pressure Range: 0-2000psi RPM: 60 (load free) Torque: 600 ft lb HP: 13 Honda Engine Features: Auxiliary Flat Faced Male and Female Quick Disconnects Ship Weight: 510 lbs Reservoir Capacity:

More information

MODEL 5500 Tire Repair Station

MODEL 5500 Tire Repair Station MODEL 5500 Tire Repair Station Installation, Operation and Repair Parts Information Branick Industries, Inc. 4245 Main Ave P.O. Box 1937 Fargo, North Dakota 58103 P/N: 81-0047C TABLE OF CONTENTS SAFETY

More information

JARVIS. Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners

JARVIS. Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners \ Models USSS -1, USSS -2 and USSS -2A Pneumatic Stunners Rear Handle for Knocker Box USSS--2A Side Handle for Knocker Box USSS--1 U.S. Patent No. 6,135,871 Patents Pending Worldwide Rear Handle for V

More information

Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers and Higher Until Superseded)

Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers and Higher Until Superseded) Parts List Wright Stander Rapid-Hite Mower (For Serial Numbers 28551 and Higher Until Superseded) Replace with newer revisions as they become available 2006 Wright Manufacturing, Inc. All rights reserved

More information

Parts List for Sentar (For Serial Numbers Prior to 19729)

Parts List for Sentar (For Serial Numbers Prior to 19729) Parts List for Sentar (For Serial Numbers Prior to 19729) Replace with newer revisions as they become available 2006 Wright Manufacturing, Inc. All rights reserved Updated 08/2006 52", 61" CUTTER DECKS

More information

Illustrated Parts List for VMAC System V900120

Illustrated Parts List for VMAC System V900120 Illustrated Parts List for VMAC System V900120 Ford 2015-2011 F250-F550 6.7L Power Stroke Diesel 1 Kit Pack List... 2 2 - Fastener Pack, 3800769... 4 3 - Compressor Assembly, P120150... 11 4 - Compressor

More information

Model 4070 Center Post Tire Changer

Model 4070 Center Post Tire Changer Model 4070 Center Post Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies. Parts Identification READ these instructions before placing unit in service. KEEP these

More information

Liftgate Terminology

Liftgate Terminology SL-20 Series SL-20 Series Click the appropriate link below for the major component of the liftgate for which you are trying to find the correct part. If you are unsure of the name of the part in Waltco

More information

JARVIS. Model 50G Hydraulic Dehorner

JARVIS. Model 50G Hydraulic Dehorner Hydraulic Dehorner EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 50G Dehorner Electric Triggers Offset Blades... 4025011 Cup Blades... 4025047 Air Triggers Offset Blades... 4025025 Cup

More information

JARVIS. Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters. TWC--1 TWC--2 and TWC--4 EQUIPMENT... TABLE OF

JARVIS. Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters. TWC--1 TWC--2 and TWC--4 EQUIPMENT... TABLE OF Model TWC -1 Tail, TWC -2 and TWC -4 Hog Toe Web Cutters TWC--1 TWC--2 and TWC--4 Patent Nos. 6,461,232 B1 6,648,746 EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model TWC--1 with Control

More information

RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers

RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers For servicing single piece automotive and most light truck tire/wheel assemblies. Model RC-45 Model RC-55 Parts Identification READ these instructions before

More information

Parts Manual DX272 / Please read the operator s manual carefully and make sure you understand the instructions before using the machine.

Parts Manual DX272 / Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Parts Manual DX22 / 966651501 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable

More information

365L (2001) Page 1 of 36 54" Deck Assembly

365L (2001) Page 1 of 36 54 Deck Assembly 365L (2001) Page 1 of 36 54" Deck Assembly 365L (2001) Page 2 of 36 54" Deck Assembly 1 720-0241 1 S Wing Nut Knob 2 703-2817 1 Belt Cover LH 3 703-2816 1 Belt Cover RH 4 747-3306 1 Idler Spring Mounting

More information

ITEM PART # EST. WT. FINAL WT. ALL DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED : ALL XX DIM. --- ALL XX.XX DIM.

ITEM PART # EST. WT. FINAL WT. ALL DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 UNLESS OTHERWISE SPECIFIED : ALL XX DIM. --- ALL XX.XX DIM. 39 38 33 36 35 34 34 24 62 27, 28, 29 63 3, 33, 34, 35, 36, 40, 62 64 2, 5, 19, 20, 32, 39, 40, 44, 47, 101, 148, 165, 167 65 8, 11, 12, 13 66 4, 5, 6, 55 67 16A, 16B, 17, 18 68 7, 22, 32, 44, 47, 48,

More information

INSTRUCTION, GPT HAND PUMP KIT (BUCHER PUMP) INSTALLATION

INSTRUCTION, GPT HAND PUMP KIT (BUCHER PUMP) INSTALLATION LIFT CORPORATION Sht. 1 of 27 DSG# M-15-13 Rev. A Date: 11/04/15 INSTRUCTION, GPT HAND PUMP KIT (BUCHER PUMP) INSTALLATION KIT P/N 296075-01 NEEDLE VALVE, ADJUSTABLE, SAE #6 P/N 906739-01 QTY. 1 CONNECTOR,

More information

Illustrated Parts List for VMAC System V90G120

Illustrated Parts List for VMAC System V90G120 Illustrated Parts List for VMAC System V90G120 Ford 2015-2011 F250-F550 6.7L Power Stroke Diesel 1 - Kit Pack List... 2 2 - Fastener Pack, V90G120, 3800843... 5 3 Compressor, Assembly, AUS, P120140...

More information

Illustrated Parts List for VMAC System H E

Illustrated Parts List for VMAC System H E Illustrated Parts List for VMAC System H00001-E 1 Main Assembly... 2 2 Inlet Valve and Compressor System, (90006 & P1002)... 3 Cooler Assembly 900069... 6 Manifold Assembly, 9000... 5 Tank Assembly, 900050...

More information

72K850ZP PARTS MANUAL

72K850ZP PARTS MANUAL 7 2 K 8 5 0 Z P PARTS MANUAL 72 MID-CUT GAS ENGINE OPTION SECTION 72 MID-CUT DECK ASSEMBLY 72" Mid-Cut Deck Assembly # PART NO. QTY DESCRIPTION 1 582096 1 72" MC DECK WELDMENT 2 582098 1 72" DECK CHANNEL

More information

WALK-BEHIND TROWEL B436 B436E B436SD. Effective Serial Numbers: , , , and higher.

WALK-BEHIND TROWEL B436 B436E B436SD. Effective Serial Numbers: , , , and higher. WALK-BEHIND TROWEL B436 B436E B436SD Effective Serial Numbers: 127458, 127543, 127782, 127834 and higher. Doc. # PB-B09001 Orig. Rel. - 05-2010 Curr. Rev. - 10 Rev. Date - 06-2014 Bartell Morrison (USA)

More information

Parts Manual PZ Please read the operator manual carefully and make sure you understand the instructions before using the machine.

Parts Manual PZ Please read the operator manual carefully and make sure you understand the instructions before using the machine. Parts Manual PZ 60 967 045601-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service questions,

More information

Spare Parts List ( ) Clipper V

Spare Parts List ( ) Clipper V Spare Parts List (1.008-026.0) Clipper 12-230V From Serial Number (Ref No1*) *See Serial Number Page or call manufacturer 86403900-C 02/23/ How to Use this Spare Parts List The PARTS LIST section contains

More information

PB18-G Series Portable Pump Service Parts List

PB18-G Series Portable Pump Service Parts List Document Number Issue Date 01/24/07 Rev. Date 7/28/16 PB18-G Series Portable Pump Service Parts List Component Pump Pump Model (Located on Serial Plate) PB18-G2015B PB18-G2015F Exploded View See Page Cross

More information

AIR INNOVATEDTM. Illustrated Parts List for VMAC System V Ford F250 F L Power Stroke Diesel

AIR INNOVATEDTM. Illustrated Parts List for VMAC System V Ford F250 F L Power Stroke Diesel AIR INNOVATEDTM Illustrated Parts List for VMAC System V910010 2011 2016 Ford F250 F550 6.7 L Power Stroke Diesel www.vmacair.com Illustrated Parts List for VMAC System V910010 Ford 2011-2016 F250-F550

More information

PARTS MANUAL. SERIAL NO: to BAND SAWING MACHINE

PARTS MANUAL. SERIAL NO: to BAND SAWING MACHINE PARTS MANUAL MODEL: TF-2025M SERIAL NO: 543-99101 to BAND SAWING MACHINE MACHINE SPECIFICATIONS MODEL VOLTAGE CYCLE PHASE SERIAL NO. For your information and future reference, insert pertinent data concerning

More information

PARTS BOOK CATALOG IMPLEMENT ASSEMBLIES STANDARD BOOM 3PT HITCH MOUNT

PARTS BOOK CATALOG IMPLEMENT ASSEMBLIES STANDARD BOOM 3PT HITCH MOUNT PARTS BOOK CATALOG IMPLEMENT ASSEMBLIES STANDARD BOOM 3PT HITCH MOUNT DIAMOND MOWERS, Inc. 350 E 60 th St. North Sioux Falls, SD 57104 FOR WARRANTY CALL DIAMOND MOWERS DIRECT: 888-960-0364 OUR TECHNICIANS

More information

Parts Manual SPEEDZTR 30 /

Parts Manual SPEEDZTR 30 / Parts Manual SPEEDZTR 30 / 966676201 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable

More information

RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers

RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers RC-45 A/E, RC-55 A/E Rim Clamp Tire Changers For servicing single piece automotive and most light truck tire/wheel assemblies. Model RC-45 Model RC-55 Parts Identification READ these instructions before

More information

Please read the operator manual carefully and make sure you understand the instructions before using the machine.

Please read the operator manual carefully and make sure you understand the instructions before using the machine. 967327901-00 Parts Zero Manual Turn Mower Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service

More information

Belt Conveyor Systems

Belt Conveyor Systems Belt Conveyor Systems Product & Installation Manual 24-in, 36-in, and 48-in Widths Manual #: IM-704-01 i 11/14 ii Table of Contents SECTION 1 OVERVIEW 1-1 System Length 1-1 Component Dimensions 1-2 Drive

More information

ALL AIR RC-15A2 RC-15A2 SPECIAL INSTRUCTIONS

ALL AIR RC-15A2 RC-15A2 SPECIAL INSTRUCTIONS ALL AIR RC-15A2 RC-15A2 SPECIAL INSTRUCTIONS The RC-15A2 uses only one power source. Compressed air at 110 to 175 PSI should be supplied to the air inlet hose at the rear of the machine. (Recommended compressor

More information

For servicing single piece automotive and most light truck tire/wheel assemblies

For servicing single piece automotive and most light truck tire/wheel assemblies 5065 A/E/AX/EX Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these and other

More information

5050 A/E. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies

5050 A/E. Tire Changer. Parts Identification. For servicing single piece automotive and most light truck tire/wheel assemblies 5050 A/E Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies Parts Identification READ these instructions before placing unit in service KEEP these and other materials

More information

Service Parts. John Deere 3029DF 3029TF 3029TF270. Engine. Engine Models: Generator Models: 20ROZJB REOZJB 20DSJB DSEJB.

Service Parts. John Deere 3029DF 3029TF 3029TF270. Engine. Engine Models: Generator Models: 20ROZJB REOZJB 20DSJB DSEJB. Service Parts Engine Engine Models: John Deere 3029DF 3029TF 3029TF270 Generator Models: 20ROZJB 20--40REOZJB 20DSJB 20--40DSEJB TP- 12/03b Table of Contents Description Page Description Page Introduction...

More information