Order online at

Transcription

1 54 Order online at 0C(S)-HMC,,, 4, 5 & -U and 0C(S)-SP- HM,,, 4, 5 Silicon Carbide Seal Kit No NOTE - Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers. Repair Parts Kit No Adapter Kit No (HM and HM4 Modes Only) Contains SP Chamber Kit No SP one drain vent plug (Ref. ) and one vent plug (Ref. A). Parts Kit No (Ref. ), motor shaft seal (Ref. washer (Ref ); two each motor housing o-rings (Ref. ), and port adapter o-rings (Ref. 0 & ). Hydraulic Motor Part Nos. Ref. No. Qty. Req d. Part No. Description Ref. No. Qty. Req d. Part No. Description 4 Drain/Vent Plug (0C) Dowel Pin (HMC / HM4C) Drain/Vent Plug (0S) A 4 Drain/Vent Plug Dowel Pin (HMC) Vent Plug Dowel Pin (HMC / HM4C) Pump Casing (Model 0C) 4 Pump Casing (Model 0S) Dowel Pin (HMC) A Pump Casing (Universal Flange Model C-U) Gerotor (HMC) A Pump Casing (Universal Flange Model S-U) Gerotor (HMC) Pump Casing Gerotor (HMC) Impeller Nut (0C) Gerotor (HM4C) Impeller Nut (0S) P Impeller (Nylon Std. 0C) Gerotor Housing (HMC Models) /4 wide P Impeller (Polypropylene Optional) (Std 0S) Gerotor Housing (HMC Models) / wide O-ring Gerotor Housing (HMC Models) wide Mechanical Seal (Viton/Ceramic) (Std 0C) Mechanical Seal (Silicon Carbide) (Std 0S) Motor End Plate (includes needle bearing) 8 Mounting Flange (0C) 8 4 Washer 8 Mounting Flange (0S) 4 Cap Screw (HMC / HM4C Models) Hex Head Cap Screw (0C) Cap Screw (HMC Models) 4 Hex Head Cap Screw (0S) Cap Screw (HMC Models) 0 Slinger Ring Snap Ring 0 O-ring Retaining Ring 0-00A Pressure Port Adapter (includes o-ring) O-ring Cartridge, Front O-ring Lip Seal Seal Spacer Washer Shaft (HMC/HM4C) Roll Pin (HMC / HM4C) Shaft (HMC) 8 Roll Pin (HMC) Snap Ring 4 Hex Head Cap Screw Woodruff Key (0C) O-ring Woodruff Key (0S) Jensen Equipment Co. (8)-7-744

2 Order online at C-HMC, 05C-HMC-SP, 05C-HMC-BSP 8 Silicon Carbide Seal Kit No Mechanical seal (Ref. 7) and o-ring (Ref. 8). Repair Parts Kit No One o-ring (Ref. 8), one rubber seal (Ref. 7). NOTE give QUANTITY, PART and COMPLETE MODEL are used ONLY to identify part in the drawing and are NOT to be used as order numbers. Hydraulic Motor Part No. Parts Kit No bearing (Ref. 4), motor shaft seal (Ref. 7), thread seal o-rings (Ref.), and washer (Ref 40); two each motor housing o-rings (Ref. ), and port adapter o-rings (Ref. 4 & 7). Ref. No. Qty. Req d. Part No. Description Drain/Vent Plug A / NPT Drain Plug (SP Model Only) NPT Prime Port Plug (SP Model Only) Pump Casing A SP Self-Priming Chamber (SP Model Only) Includes Stainless Wear Ring, Plugs & O-Ring A 40- Includes Stainless Wear Ring, Plugs & O-Ring Impeller Nut Washer P Impeller Mechanical Seal (Silicon Carbide) (Optional) O-Ring Mounting Flange Hex Head Cap Screw Slinger Ring Snap Ring Retaining Ring Cartridge, Front O-Ring Lip Seal Seal Spacer Ref. No. Qty. Req d. Part No. Description Square Key Shaft Snap Ring Roll Pin 4 4 Hex Head Cap Screw O-Ring 7 Dowel Pin Dowel Pin Gerotor 0 Gerotor Housing wide Motor End Plate (includes needle bearing) Washer Cap Screw O-Ring 0-00A Pressure Port Adapter (includes o-ring) O-ring Washer Jensen Equipment Co. (8)-7-744

3 5 Order online at 0C(S)-HM,, 5C and 0C(S)-HM,, 5C-U Silicon Carbide Seal Kit No Mechanical seal (Ref.7) and o-ring (Ref. 5). Repair Parts Kit No One mechanical seal (Ref. 7), one o-ring NOTE give QUANTITY, PART Reference number are used ONLY to identify part in the drawing and are NOT to be used as order numbers. Parts Kit No bearing (Ref. ), motor shaft seal (Ref. ), thread cartridge o-rings (Ref.5), and washer (Ref ); two each motor housing o-rings (Ref. ), and port adapter o-rings (Ref. 0 & ). Hydraulic Motor Part Nos C (HMC Models) C (HMC Models) C (HM5C Models) Ref. Qty. Part No. Description No. Req d Drain/Vent Plug (0C) Drain/Vent Plug (0S) C Pump Casing (0C) S Pump Casing (0S) A C Pump Casing (Universal Flange 0x00) C Pump Casing (Universal Flange 00x0 Cast) S Pump Casing (Universal Flange 00x0 S.S.) Impeller Nut (0C) Impeller Nut (0S) P Impeller (Nylon Std. 0C) P Impeller (Polypropylene Optional) (Std. 0S) P Impeller (GTX Optional) O-ring Mechanical Seal (Viton/Cermaic) (Std. 0C) Mechanical Seal (Silicon Carbide) (Std. 0S) C Mounting Flange (0C) S Mounting Flange (0S) Hex Head Cap Screw (0C) Hex Head Cap Screw (0S) Slinger Ring Snap Ring Retaining Ring Cartridge, Front O-ring Lip Seal Seal Spacer Shaft (HMC/HM5C) Shaft (HMC) Ref. Qty. Part No. Description No. Req d C Hex Head Cap Screw O-ring Dowel Pin (HMC/HM5C) Dowel Pin (HMC) Dowel Pin (HMC/HM5C) Dowel Pin (HMC) Gerotor (HMC) Gerotor (HMC) Gerotor (HM5C) C Gerotor Housing (HMC Models) / wide C Gerotor Housing (HMC Models) wide C Gerotor Housing (HM5C Models) 5/8 wide C Motor End Plate (includes needle bearing) Washer Cap Screw (HMC Models) Cap Screw (HMC Models) Cap Screw (HM5C Models) O-ring 0-00A Pressure Port Adapter (includes o-ring) 70-0 O-ring 0-005A Washer Roll Pin (HMC/HM5C) Roll Pin (HMC) Snap Ring Woodruff Key (0C) Woodruff Key (0S) Jensen Equipment Co. (8)-7-744

4 Order online at C-O, 0C-O, 008C-O, 08C-O, 08C-O, 00, 00C-O-SP, 0C-O-SP, 08C-O-SP Ref. No. Qty. Req d. Part No. Description Drain Plug Drain Plug Pump Casing (w/ SS wear ring) A SP Pump Casing (Self-Priming Units) Impeller Nut P Impeller (Nylon) Mechanical Seal (Standard Viton) O-Ring 8 Mounting Flange Adapter Hex Head Capscrew O-Ring Retaining Ring Capscrew NOTE give QUANTITY, PART and COMPLETE MODEL number are used ONLY to identify part in the drawing and are NOT to be used as order numbers. Seal, O-Ring Repair Kit No Mechanical Seal and () Ref. 7 O-Ring. Gear Lube Requirement: 8oz. Phillube SAE 80W0 Oil Life Guard Seal Kit No Ref. and Ref. 7. Ref. No. Qty. Req d. Part No. Description Impeller Shaft (000rpm) Sun Gear (000 rpm) Retaining Ring (000 rpm) Hex Head Capscrew Washer Thrust Washer Driver Hub (Model 008C-O) Driver Hub (Model 08C-O) 7 Key 8 Driver Hub (Model 0C-O) 0 Driver Hub (Model 00C-O) () req d for 000 rpm models. 4 Capscrew (Model 08C) Driver Hub (Model 08C) Retaining Ring Retaining Ring Ring Gear Gear Casing Hex Head Capscrew Oil Seal O-Ring Oil Plug 4 Mounting Clip Capscrew Jensen Equipment Co. (8)-7-744

5 58 Model 40C, 40C, 40S and 40C-SP Order online at Model 40C, 40C, 40S and 40C-SP Model 40C, 40C, 40S and 40C-SP C 4 5 8A 8B 8C A 8B A Series 40C, 40C, 40S and 40C-SP A L-00C (/0) Ref. Qty. Part No. Req'd No. Description Drain Plug C Pump Casing (Model 40C) S Pump Casing (Model 40S) C Pump Casing (Model 40C) A SP Pump Casing (Model 40C-SP) (The above casings include a 0 stainless steel wear ring.) Impeller Nut Impeller Nut (Model 40S) P Impeller (Nylon) (standard) P Impeller (Polypropylene) (40S std.) O-Ring Mechanical Seal (optional Buna-N) Mechanical Seal (standard Viton) L-00C (/0) Mechanical Seal (opt. Silicon Carbide) Slinger Ring C Mounting Flange S Mounting Flange (Model 40S) Nameplate (Specify Model Number) Bolt Bolt (Model 40S) Ball Bearing Key Pump Shaft Key Bearing Retainer Gasket D Pedestal Bracket Driver Shaft Bearings Driver Shaft Bearing Retainer Ring Bearing Spacer End Cap (label) Bearing Bore Retaining Ring Driver Pulley (540 rpm) Driver Pulley (000 rpm) Driver Pulley (000 rpm, -/4" shaft) Key (Driver Pulley) Key (Driver Pulley, -/4" shaft) Retaining Ring (Driver Pulley) Retain. Ring (Dr. Pulley, -/4" shaft) F Shaft (540 rpm)( kit used on F and F shafts) F Shaft (000 rpm) ( kit used on F and F shafts) F Shaft (-/4" 000 rpm) (40-00 kit used on F shaft) F Shaft (540 Quick Coupler) Ref. Qty. Part No. Req'd. No. Description 8A Locking Ball 8B Collar Spring 8C Collar Shaft (" solid) Driven Pulley (5/8" dia. bore) Set Screw for Driven Pulley C Idler Bracket (Cast Iron Pumps) Grease Zerk Fitting Retaining Ring (Idler Bracket, Cast Iron) Idler Pulley Spacer (Idler Pulley) Retaining Ring (Idler Pulley) Torsion Spring (Idler for Cast Iron) 0-0 Idler Bolt/Shaft Belt Shield Belt Shield Bracket for Belt Shield Attachment Bolt for Shield Assembly Bolts for Shield Assembly Nuts for Shield Poly V-Belt (540 rpm) Poly V-Belt (000 rpm) Bolts for Pump to Bracket Lock Washers for Bracket Bolts Roll Pin NOTE: When ordering parts, give QUANTITY, PART NUMBER, DESCRIPTION, and COMPLETE MODEL NUMBER. Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers. Repair Kit No (for 540 rpm drives) consists of () Ref. 4 Poly V-Belt, () Ref. 5 O-ring, () Ref. Mechanical Seal (Viton) and () Ref. 7 Gasket. Repair Kit No (for 000 rpm drives) consists of () Ref. 4 Poly V-Belt, () Ref. 5 O-ring, () Ref. Mechanical Seal (Viton) and () Ref. 7 Gasket. Seal Repair Kit No consists of () Ref. Mechanical Seal (Viton- Std.), () Ref. 5 O-ring and () Ref. 7 Gasket. Life Guard Seal Repair Kit No consists of () Ref. Mechanical Seal (Silicon Carbideoptional) and () Ref. 5 O-ring. Jensen Equipment Co. (8)-7-744

6 Order online at 5 D 5 0C, 0S & 0C-R & 0S-R, 0C-SP, 0C-R-SP & 0S-SP C A B 4A () Ref. O-Ring A Standard Seal Kit No () Ref. O-Ring NOTE DESCRIPTION, and COMPLETE are used ONLY to identify part in the drawing and are NOT to be used as order numbers. Ref. Qty. Part No. Description No. Req d Drain Plug (Cast Series) A Drain Plug (Stainless Steel) Drain Plug Pump Casting (Cast Series) Pump Casting (Stainless Series) A Pump Casting (Reverse)(Cast Series) A Pump Casting (Reverse)(Stainless) Pump Casting (Flanged)(Stainless) Pump Casting (Flanged)(Stainless) C Self Priming Chamber C Self Priming Chamber (Stainless) D Self Priming Chamber A P Impeller (Cast Series) P Impeller (Stainless Series) P Impeller (GTX) Ref. Qty. Part No. Description No. Req d. 4A P Impeller (Reverse)(Cast Series) 4A P Impeller (Reverse)(Stainless) 40-0 Mechanical Seal Mechanical Seal (Stainless Steel) O-Ring 7 Mounting Flange (Cast Series) 7 Mounting Flange (Stainless Series) Key (Cast Series) Key (Stainless Series) Shaft Slinger Ring Protective Cover Pipe Plug Jensen Equipment Co. (8)-7-744

7 0 Order online at 7 X-FMC.EPS A REF. # PART NUMBER EDP # DESCRIPTION REQ. BAC-5 40 Pipe plug Pipe plug, stainless steel (optional) BAC Volute, /4 x BAC--VALOX 4040 Impeller, Valox, left hand thread BAC--CI 404 Impeller, cast iron, left hand thread (optional) 4 jk BAC-4A O-ring, body seal 4 BAC Gasket, 4 hole, (obsolete ) 5j BAC-7V 405 Seal, mechanical, Viton, includes 400 O Ring 5k BAC-7SC 405 Seal, mechanical, silicon carbide, includes 400 (optional) 5Ajk O Ring for BAC- shaft BAC-4-F 400 Mounting frame Cap screw, /8 NC x /4 hex head Cap screw, /8 NC x /4 hex head, stainless steel (optional) 4 8 BAC Slinger BAC Snap ring, internal, BAC-4 mounting frame 0 BAC Ball bearing, sealed, BAC- shaft BAC Snap ring, external, BAC- shaft BAC--S 4075 Spacer for BAC- shaft BAC--SS Shaft, 5/8 diameter, left hand thread, stainless steel 4 BAC Key, / x / x -/4 j RK-FMC 5700 Repair kit for FMC series - k RK-FMCSC 570 Repair kit for FMC series with silicon cardide seal - Jensen Equipment Co. (8)-7-744

8 Order online at 8 FMC A 0 REF. # PART # EDP # DESCRIPTION REQ. BAC-5 40 Pipe plug,/8 NPT Pipe plug,/8 NPT, stainless steel (optional) 4 BAC Volute, -/ x -/4, cast iron BAC--A 40 Nut, /8 NF Hex, cad plated locknut BAC--B-SS 40 Nut, /8 NF, stainless steel (standard on -SS models) 4 jk BAC-4-HYD-SS Washer, /8, stainless steel 4 BAC-4-B-SS 470 Washer, /8, stainless steel, vibration proof (standard on -SS models) 5 BAC--50-P Impeller, Valox with keyway 5 BAC--50-CI 4044 Impeller, cast iron with keyway (optional) 5 BAC--50-PI Impeller, polypropylene, keyway (optional) jk BAC O-ring for BAC--50 volute seal 7 j BAC-7V 405 Seal, Viton mechanical seal (includes 400 O-ring) 7 jk BAC-7SC 405 Seal, Silicon carbide mechanical seal (includes 400 O-ring)(optional) 7A jk O-ring for BAC- shaft 8 BAC-4-50-F 400 Mounting frame Cap screw, /8 NC x /4 Hex head, stainless steel (optional) Cap screw, /8 NC x /4 Hex head 4 0 BAC Slinger BAC Snap ring, internal, BAC-4 mounting frame BAC Bearing, BAC- driven shaft BAC Snap ring, external, BAC- driven shaft 4 BAC--S 4075 Spacer for BAC- shaft 5 BACH Key, /8 x /8 x / BAC--50/00-SS 4005 Shaft, 5/8 Driven shaft with keyway, stainless steel 7 BAC Key, / x / x -/4 j RK-FMC Repair kit for FMC-50 series - k RK-FMCSC Repair kit for FMC-50 series with silicon carbide shaft seal - Ace Pump Corporation 50 Channel Avenue Memphis, TN 8 Jensen Equipment Co. (8)-7-744

9 Order online at FMC-50-HYD Jensen Equipment Co. (8) A 0 REF. # PART NUMBER EDP # DESCRIPTION REQ. BAC-5 40 Pipe plug Pipe plug, stainless steel (optional) 4 BAC Volute, -/ x -/4 BAC--A 40 Nut, /8 NF, cad plated BAC--A-SS 40 Nut, /8 NF, stainless steel (optional) 4 BAC-4-HYD-SS Washer, /8 star, stainless steel 5 BAC--50-P 4044 Impeller, Valox, keyway 5 BAC--50-CI Impeller, cast iron, keyway (optional) BAC-7V 405 Seal, carbon/ceramic/viton (includes 400 O-Ring) BAC-7SC 405 Seal, silicon carbide/viton (includes 400 O-Ring) (optional) A O-ring, shaft seal 7 BAC O-ring, body seal 8 BAC-4-50-HYD 4005 Mounting frame (for 00 Series hydraulic motor) Cap screw, /8 NC x /4 hex head Cap screw, /8 NC x /4 hex head, stainless steel (optional) 4 0 BAC Slinger BAC Snap ring, internal, BAC-4 mounting frame BAC Ball Bearing, sealed, BAC- shaft BAC Snap ring, external, BAC- shaft 4 BAC--S 4075 Spacer for BAC- shaft 5 BACH Key, /8 x /8 x / BAC--HYD-SS 400 Shaft, 5/8 diameter, keyway and tang slot, stainless steel 7 BAC-75-HYD-0 47 Hydraulic motor, 7 GPM (includes parts 8-5) 8 S00 40 Seal support spacer for 00 Series HYD motor BAC-75-HYD-0N 47 Hydraulic motor, 7 GPM (motor only - no external fittings) Cap screw, 5/ N. C. x -/4 socket head (for 0N motor) O-ring, #8 SAE fitting BAC-78-8SAE 444 Reverse check valve, #8 SAE male x / NPT female BAC-80-8SAE 4455 Adapter, restrictor body, #8 SAE male x / NPT female O-ring, orifice insert 5 BAC Orifice, restrictor insert,.0 (0N) LS-0N 448 Flow limiting valve (0N), #8 SAE male x / NPT female RK-FMC Repair kit for FMC-50 series pump - RK-FMCSC Repair kit for FMC-50 series with silicon carbide shaft seal - # RK-BAC-75-HYD-L 474 Repair kit for 00 Series motor with high pressure lip seal - Ace Pump Corporation 50 Channel Avenue Memphis, TN 8 Phone: Fax: Ace Form # FMC-50-HYD Revised 08/08

10 Order online at FMC-00-HYD A REF # PART NUMBER EDP # DESCRIPTION REQ. BAC-5 40 Pipe plug Pipe plug, stainless steel (optional) 4 7AC-4-CCW 45 Volute, x -/ BAC--A 40 Nut, /8 NF, cad plated 4 BAC-4-HYD-SS Washer, /8 star, stainless steel 5 BAC--00-CI 404 Impeller, with extended keyway, cast iron (optional) 5 BAC--00-P 4044 Impeller, with extended keyway, thermoplastic BAC-4A O-ring, body seal 7 BAC-7V 405 Seal, carbon/ceramic/viton (includes 400 O Ring) 7 BAC-7SC 405 Seal, silicon carbide (includes 400 O Ring) (optional) 7A O-ring, shaft seal 8 BAC-4-HYD-00A 404 Mounting frame (for -00A series hydraulic motor) Cap screw, /8 NC x /4 hex head Cap screw, /8 NC x /4 hex head, stainless steel (optional) Cap screw, 5/ N. C. x /4 hex head, motor to pump 4 BAC Slinger BAC Snap ring, internal, BAC-4 mounting frame BAC Ball Bearing, sealed, BAC- shaft 4 BAC Snap ring, external, BAC- shaft 5 BAC--S 4075 Spacer for BAC- shaft BAC Key, /8 x /8 x /, extended keyway 7 BAC--HYD-00-SS 400 Shaft, extended keyway, tang, stainless steel 8 S00 40 Seal support spacer for 00 Series HYD motor, effective /00 BAC-75-HYD-04A 488 Hydraulic motor, GPM, /" NPT ports BAC-75-HYD-04A-SAE 44 Hydraulic motor, GPM, # SAE end ports (optional) RK-FMC 5700 Repair kit for FMC series pump - RK-FMCSC 570 Repair kit for FMC series pump with silicon carbide shaft seal - # RK-BAC-75-HYD-00-L 4 Repair kit for 00 Series -L motor - Jensen Equipment Co. (8)-7-744

11 4 Technical information Useful Formulas GPM GPA x MPH x W = (Per Nozzle) 5,40 GPM GAL/000FT x MPH x W = (Per Nozzle) GPA = 5,40 x GPM (Per Nozzle) MPH x W x GPM (Per Nozzle) GAL/000FT = MPH x W GPM Gallons Per Minute GPA Gallons Per Acre GAL/000FT Gallons Per 000 Square Feet MPH Miles Per Hour W Nozzle spacing (in inches) for broadcast spraying Spray width (in inches) for single nozzle, band spraying or boomless spraying Row spacing (in inches) divided by the number of nozzles per row for directed spraying Useful Formulas for Roadway Applications Nozzle Spacing If the nozzle spacing on your boom is different than those tabulated, multiply the tabulated GPA coverages by one of the following factors. GPLM = 0 x GPM GPM = GPLM x MPH MPH 0 GPLM = Gallons Per Lane Mile Note: GPLM is not a normal volume per unit area measurement. It is a volume per distance measurement. Increases or decreases in lane width (swath width) are not accommodated by these formulas. Measuring Travel Speed Measure a test course in the area to be sprayed or in an area with similar surface conditions. Minimum lengths of 00 and 00 feet are recommended for measuring speeds up to 5 and 0 MPH, respectively. Determine the time required to travel the test course. To help ensure accuracy, conduct the speed check with a partially loaded (about half full) sprayer and select the engine throttle setting and gear that will be used when spraying. Repeat the above process and average the times that were measured. Use the following equation or the table at right to determine ground speed. Distance (FT) x 0 Speed (MPH) = Time (seconds) x 88 Speeds Speed in MpH TiMe ReqUiRed in SeCONdS TO TRAvel A distance OF: 00 Feet 00 Feet 00 Feet OTHeR SpACiNg (inches) CONveRSiON FACTOR OTHeR SpACiNg (inches) CONveRSiON FACTOR OTHeR SpACiNg (inches) CONveRSiON FACTOR Miscellaneous Conversion Factors One Acre = 4,50 Square Feet = FT Blocks = Hectare One Hectare =.47 Acres One Gallon Per Acre =. Fluid Ounces per 000FT =.5 Liters Per Hectare One Gallon Per 000FT = 4.5 GPA One Mile = 5,80 Feet =,0 Meters =. Kilometers One Gallon = 8 Fluid Ounces = 8 Pints = 4 Quarts =.7 Liters = 0.8 Imperial Gallon One Pound Per Square Inch = 0.0 bar =.8 Kilopascals One Mile Per Hour =.0 Kilometers Per Hour Suggested Minimum Spray Heights The nozzle height suggestions in the table below are based on the minimum overlap required to obtain uniform distribution. However, in many cases, typical height adjustments are based on a to nozzle spacing to height ratio. For example, 0 flat spray tips spaced 0 inches apart are commonly set 0 inches above the target. (inches) TP, TJ TP, XR, TX, DG, TJ, AI, XRC TP, XR, DG, TT, TTI, TJ, DGTJ, AI, AIXR, AIC, XRC, TTJ, AITTJ FullJet FloodJet TK, TF, K, QCK, QCTF, /4TTJ ** 4 *** ** 5 7*** NR* NR* NR* 4 8** 8 0*** * Not recommended. ** Nozzle height based on 0 to 45 angle of orientation (see page 4 of catalog). *** Wide angle spray tip height is influenced by nozzle orientation. The critical factor is to achieve a double spray pattern overlap

12 5 Note: TeeJet Technologies recommends the use of sealed connectors to improve reliability and prolong component life. PACKARD IDŐJÁRÁSI AMP MALE CSOMAG FASTON CONNECTOR TORONYCSATLAKOZÓ (SZIGETELT) Note: No pin-out code needed with these connectors. Electrical Connectors CHART : CONNECTOR CODES AMP FEMALE FASTON CONNECTOR Note: No pin-out code needed with these connectors. -PIN = CODE A -PIN = CODE J AMP FEMALE MATE-N-LOK CONNECTOR (SEALED) -PIN = CODE B -PIN = CODE K AMP MALE MATE-N-LOK CONNECTOR (SEALED) Pin Pin Pin Pin -PIN OR -PIN -PIN = CODE C -PIN = CODE L PACKARD WEATHER PACK SHROUD CONNECTOR (SEALED) Pin -PIN = CODE E -PIN = CODE O -PIN = CODE D -PIN = CODE M PACKARD WEATHER PACK TOWER CONNECTOR (SEALED) Pin -PIN = CODE F -PIN = CODE P DEUTSCH DT FEMALE CONNECTOR (SEALED) DEUTSCH DT MALE CONNECTOR (SEALED) Pin B A Pin A B -PIN = CODE G -PIN = CODE Q PACKARD METRIPACK FEMALE CONNECTOR (SEALED) C -PIN = CODE H JST VH FEMALE CONNECTOR (SEALED) -PIN = CODE R C -PIN = CODE S PACKARD WEATHER PACK SHROUD CONNECTOR (SEALED) PACKARD WEATHER PACK TOWER CONNECTOR (SEALED) -PIN = CODE I -PIN = CODE T 4-PIN = CODE U 4-PIN = CODE V 4-PIN CODE LETTER DEUTSCH DT FEMALE CONNECTOR 4-PIN = CODE W CHART : PIN-OUT CODES CONNECTOR POSITION CONNECTOR POSITION CODE LETTER A OR B OR C OR D OR 4 A OR B OR C OR D OR 4 A R W P B M P R W B B R W B P N P R B W C R B W P O P W R B D R B P W P P W B R E R P W B Q P B R W F R P B W R P B W R G W R B P S B R W P H W R P B T B R P W I W P R B U B W R P J W P B R V B W P R K W B R P W B P R W L W B P R X B P W R 4 How to order: This system is to be used for 44B and 5B ball valves and 440B, 450B, 40B and 40B ball valve manifolds equipped with electrical connectors. Connector and pin-outs are to be specified in valve or manifold part number when ordering. Note: On -pin connectors, only pin-out code C or S is used. First: Specify code for connector desired (See Chart ). Second: Specify appropriate wire pin-out arrangement (See Chart ). Example: 5BEC-CLB Pin-out Code Connector Code Wire Codes: R = Red (+V) W = White (Switched) P = Plugged B = Black (Ground)

13 JENSEN EQUIPMENT CO SPRAY PARTS WAREHOUSE 55 N. 400TH STREET NEWTON, IL 448 TEMP RETURN SERVICE REQUESTED BOUND PRINTED MATTER OR CURRENT RESIDENT BPM US POSTAGE PAID NEWTON, IL. PERMIT #0