PARTS MANUAL T-TANK SPRAYER 1100 GALLON

Transcription

1 PARTS MANUAL T-TANK SPRAYER 1100 GALLON Part No. TA

2 TABLE OF CONTENTS Description...Page Product Identifi cation... 3 Tank Frame Assembly... 5 Tank Baffl e Breakdown... 6 Sprayer Tongue Mounting... 7 Sprayer Tongue Accessories... 8 Pump Mounting... 9 PTO & Q-Shaft Breakdown Shield Mountings Platform, Door & Step Mounting Clean Water Tank Mounting Plumbing Door & Sump Valve Handle Command Center Mounting Command Center T-Tank Plumbing Strainer Control System Adjustable Axle Mounting & 120 Rigid Axle Mountings Hub Assemby Hub Assembly Sight Glass Mounting Speed Sensor Kit (Option) Tank Fittings / Functions Decals Revised WARNING! THIS PRODUCT MAY CONTAIN A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, OR BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. 2

3 3 Introduction

4 INTRODUCTION Foreword This symbol identifies important safety messages. When you see it, read the message that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them carefully and follow them closely when working around or using this machine. Read and study this manual completely before attempting to operate this implement. Take this manual to the fi eld for handy reference when operating, adjusting or servicing your machine. When referenced, "Right-Hand" (RH) and "Left-Hand" (LH) side of the machine are determined by standing behind the machine and facing in the direction of travel. Product Identification When ordering parts or when requesting further information or assistance, always give the following information: - Machine name - Model number - Serial number All products manufactured by Alliance Product Group are warranted to be free from material and workmanship defects for one full year from time of consumer delivery. Your local dealer will gladly assist you with any warranty questions. Please fi ll out and retain this portion for your records. The serial number decals for the base frame and wing frame are located on the front surface of each frame. Purchase Date Model Serial No.'s Dealer City Dealer Contact Phone NOTE: The information, specifications, and illustrations in the manual are on the basis of information available at the time it was written. Due to continuing improvements in the design and manufacture of Alliance/ Top Air products, all specifi cations and information contained herein are subject to change without notice. Revised

5 TANK FRAME ASSEMBLY ITEM DESCRIPTION PART NO. QTY. NOTES 1000 Gallon T-Tank TA T-Tank Lid 16" Hinged (Not Shown) TA Lid O-Ring (Not Shown) TA For Lids With 1/4 1 Turn Locking Style Optional Lid O-Ring (Not Shown) TA For Lids With Hinge Vent Lid (Not Shown) TA Main Frame & Fence TA680005* 1 2a Left Fence - Beginning w/ SN B TA * 1 2b Right Fence - Beginning w/ SN B TA * 1 3 Tank Stop Strap TA620004B 2 4 Capscrew 1/2-13UNC x Grade 5 Flat Washer 1/ Lock Washer 1/ Hex Nut 1/2-13UNC Tank Strap TA A/R Specify in Feet 8 Tank Strap Clip TA Capscrew 3/8-16UNC x 4 1/2 TA Flat Washer 3/8" Hex Nut 3/8-16UNC Handle Assembly TA640040B 2 13 Carriage Bolt 5/16-18UNC x Grade 5 14 Lock Washer 5/ Hex Nut 5/16-18UNC *Specify Color as R for Red or G for Green (December 2012) 5

6 TANK BAFFLE BREAKDOWN VIEW OF INSIDE OF TANK ITEM DESCRIPTION PART NO. QTY. NOTES 1 Baffl e Top Section TA Baffl e Bottom Section TA Capscrew 5/16-18UNC x 3/4 TA Stainless Steel 4 Lock Washer 5/16 TA Stainless Steel 5 Hex Nut 5/16-18UNC TA Stainless Steel 6 T-Tank Baffl e TA

7 SPRAYER TONGUE MOUNTING ITEM DESCRIPTION PART NO. QTY & 1100 Tongue Frame TA640010* 1 2 Capscrew 1-8UNC x 5 1/ /2" Tongue Spacer TA620201B 4 4 Lock Washer 1" Hex Nut 1-8UNC Tongue Adjuster Plate TA640011B 2 7 Capscrew 1-8UNC x Adjuster Bolt, 1-8UNC x 7 TA Hex Jam Nut 1-8UNC Flat Washer 1" Adjuster Bushing TA620203B 1 12 Capscrew 3/4-10UNC x 6 1/ Spacer Holder TA620267B 2 14 Lock Washer 3/4" Hex Nut 3/4-10UNC /4" Tongue Spacer TA620257B " Tongue Spacer TA620258B " Tongue Spacer TA620259B 2 *Specify Color as R for Red or G for Green NOTE: THERE ARE DIFFERENT ARRANGEMENTS FOR THE SPACERS ON SPRAYERS WITH DIFFERENT TIRE SIZES. STANDARD 3 1/4 TONGUE SPACERS (PER SIDE) 1 1 TONGUE SPACER (PER SIDE) 1 2 TONGUE SPACER (PER SIDE) TIRE 4 1/4 TONGUE SPACERS (PER SIDE) 1 1 TONGUE SPACER (PER SIDE) 1 2 TONGUE SPACER (PER SIDE) TIRE 5 1/4 TONGUE SPACERS (PER SIDE) 1 1 TONGUE SPACER (PER SIDE) 1 2 TONGUE SPACER (PER SIDE) 7

8 SPRAYER TONGUE ACCESSORIES NOTE: WHEN USING PTO DRIVEN BELT DRIVE, ITEM #12 GOES ON THE OUTSIDE OF THE PILLOW BLOCK PLATE. ITEM DESCRIPTION PART NO. QTY. 1 Pintle Hitch w/clevis TA a Pintle Hitch TA b Clevis Hitch TA c Capscrew 3/4-10UNC x 6 (Grade 8) d Lock Washer 3/ e Hex Nut 3/4-10UNC Pintle Hitch w/pintle HDW (237VOA) 2a Pintle Hitch TA b Pintle Hitch Top Plate (PPI-302V) TA c Pintle Hitch V-Plate (PPI-203VR) TA d Pintle Hitch Cushion (PPI-205H) TA e Capscrew 3/4-10UNC x 3 (Grade 5) Capscrew 3/4-10UNC x 6 1/2 (Grade 5) Lock Washer 3/4" Hex Nut 3/4-10UNC Utility Jack, 5000 Lbs. TA Hose Holder TA Capscrew 1/2-13UNC x 1 1/2 (Grade 5) Flat Washer 1/ Lock Washer 1/ Hex Nut 1/2-13UNC Hose Holder Mounting Bracket TA521932B 1 13 Capscrew 3/8-16UNC x 1 1/2 (Grade 5) Lock Washer 3/ Hex Nut 3/8-16UNC Pump Mounting Support TA620036B 1 17 Transport Chain Capscrew 1-8UNC x 3 (Grade 5) Locknut 1-8UNC TA PINTLE HITCH WITH CLEVIS (STANDARD) PINTLE HARDWARE (OPTIONAL) 8

9 HYDRAULIC DRIVEN PUMP MOUNTING ITEM DESCRIPTION PART NO. QTY. 1 Ace Hydraulic Drive Pump TA825195* 1 2 Velocity Fuse (Not Shown) TA Capscrew 3/8-16UNC x 1 1/2 (Grade 5) Flat Washer 3/ Lock Washer 3/ Hex Nut 3/8-16UNC Straight Hose Barb (1 1/2-11 1/2 MPT x 2 Hose Barb) TA Elbow (2 Flange x 1 1/2 Hose Barb) TA Elbow (2 Flange x 2 Hose Barb) TA Gasket 2 3/16" OD x 1 5/8" ID TA Adapter (2 Flange x 1 1/4-11 1/2 NPTF) TA Flange Clamp 2" Worm Screw TA Decal, IMPORTANT TA Hyd. Hose Kit (Not Shown) TA Hose Wrap, 3" (Not Shown) *SEE PUMP OPERATOR MANUALS FOR PART NUMBERS ON YOUR PARTICULAR PUMP PTO DRIVEN PUMP MOUNTING ITEM DESCRIPTION PART NO. QTY 1 Ace Belt Drive Pump ** 1 2 Belt Drive Bracket TA540287B 1 3 Capscrew 3/8-16UNC x Flat Washer 3/ Lock Washer 3/ Hex Nut 3/8-16UNC Capscrew 3/8-16UNC x 1 1/ Strt Hose Barb (1 1/2-11 1/2 MPT x 2 Hose Barb) TA Elbow (1 1/4-11 1/2NPT Male x 1 1/4-11 1/2NPT Female) TA Adapter (2 Flg x 1 1/4-11 1/2 NPTF) TA Gasket 2 3/16" OD x 1 5/8" ID TA Flange Clamp 2" Worm Screw TA Strt Hose Barb (2 Flg x 1 1/2 HB) TA Elbow (1 1/2-11 1/2NPT Male x 1 1/2-11 1/2NPT Female) TA **SEE PUMP OPERATOR MANUALS FOR PART NUMBERS ON YOUR PARTICULAR PUMP PUMP IS VIEWED FROM REAR OF SPRAYER FOR CLARITY 9

10 SPRAYER PUMP ITEM DESCRIPTION PART NO. QTY. NOTES Pump Complete - Ace TA Pipe Plug TA Pipe Plug (Option) TA Stainless Steel 2 Volute, 1 1/2" x 1 1/4" TA Nut 3/8-24UNF TA Star Washer, 3/8" TA Stainless Steel 5 Impeller, Valox - Keyway TA Impeller, Cast Iron - Key (Option) TA Seal Mechanical w/6a - Viton TA Seal w/6a - Silecon Carbide (Option) TA a O-Ring, Shaft Seal TA O-Ring, Body Seal TA Mounting Frame, 200 Motor TA Capscrew 3/8-16UNC x 3/4 TA Capscrew 3/8-16UNC x 3/4 (Option) TA Stainless Steel 10 Slinger TA Snap Ring, Internal TA Ball Bearing, Sealed TA Snap Ring, External TA Spacer TA Key 1/8 x 1/8 x 1/2 TA Shaft 5/8" Dia. - Keyway TA Shaft 5/8" Dia. - Keyway (Option) TA Stainless Steel 17 Seal Support Spacer TA Coupling, Motor TA Hydraulic Motor, 7 GPM TA

11 PTO SHAFT PARTS BREAKDOWN Introduction ITEM DESCRIPTION PART NO. QTY. NOTES 1 PTO Shaft 1000 RPM (Complete) TA PTO Shaft 540 RPM (Complete) TA Outer Plastic Shield w/bell TA Inner Plastic Shield w/bell TA Snap Hitch Yoke (1000 RPM) TA Snap Hitch Pin Kit (1000 RPM) TA Snap Hitch Yoke (540 RPM) TA Snap Hitch Pin Kit (540 RPM) TA Outer Drive Tube w/yoke TA Inner Drive Tube w/yoke TA Implement Yoke TA Cross Kit (Complete) Bearings, Snap Ring, & Washer TA Not Shown Decal, DANGER - PTO Shaft TA Not Shown Decal, DANGER - Shield TA Not Shown Q-SHAFT ASSEMBLY ITEM DESCRIPTION PART NO. QTY. NOTES 1 Q-Shaft TA510168B 1 TA Kit for Q-Shaft Assembly 2 U-Joint (Complete) TA Pillow Block Bearing TA Keystock 1/4 x Keystock 1/4 x 1 1/ Capscrew 5/16-18UNC x 2 1/ Grade 5 7 Locknut 5/16-18UNC (December 2012) 11

12 PTO & Q-SHAFT SHIELD MOUNTING ITEM DESCRIPTION PART NO. QTY 1 PTO Shield TA521268B 1 2 PTO Shield Extension TA521267B 1 3 Shaft Shield Mount TA620268B 2 PTO Shield Mount Hypro Dr. TA620341B 2 4 Shield Mounting Bracket TA521221B 1 5 Pillow Block Bearing TA Pillow Block MTG Plate TA521223B 1 7 Capscrew 1/4-20UNC x 3/ Flat Washer 1/ Cage Nut 1/4-20UNC TA Capscrew 3/8-16UNC x Flat Washer 3/ Lock Washer 3/ Hex Nut 3/8-16UNC Capscrew 3/8-16UNC x 1/ Carriage Bolt 3/8-16UNC x 1/ Decal, CAUTION PTO Shield TA Decal, WARNING Drawbar TA Decal, WARNING PTO TA

13 PLATFORM, DOOR & STEP MOUNTING ITEM DESCRIPTION PART NO. QTY 1 Platform w/handle TA * 1 2 Step Left TA * 1 Step Right (Not Shown) TA * 1 3 Capscrew 3/8-16UNC x 1 1/2 (Grade 5) Flat Washer 3/ Bushing TA Lock Washer 3/ Hex Nut 3/8-16UNC Step Spring TA Ladder Stop TA Capscrew 1/4-20UNC x 1 (Grade 5) Lock Washer 1/ Plumbing Door Latch TA620107B 1 13 Flat Washer 1/ Pop Rivet, 3/16 TA Plumbing Door Asy TA * 1 16 Capscrew 5/8-11UNC x 1 3/4 (Grade 5) Locknut 5/8-11UNC MOUNTING DETAIL *Specify Color as R for Red or G for Green 13

14 CLEAN WATER TANK MOUNTING ITEM DESCRIPTION PART NO. QTY. NOTES 1 Clean Water Tank TA Spigot TA /4 MPT x 1/2 HB Straight TA Hose Clamp, 1/4" x 3/8" TA Clear Vinal Hose, 1/2 x 24" TA Elbow, 3/4 MPT x 1/2 HB 90 TA Kelch Cap TA Lid For Storage Compartment TA Hinges (Not Shown) TA Stainless Steel 2 TA Cast 10 Decal TA Closure Fastener TA Mounting Bracket TA Capscrew, 5/16NC x 3/ Flat Washer, 5/ TA COMPLETE CLEAN WATER TANK ASSEMBLY w/ MOUNTING BRACKET & HARDWARE. 14 (December 2012)

15 PLUMBING DOOR ACCESSORIES ITEM DESCRIPTION PART NO. QTY. NOTES 1 T-Handle Black TA PSI Gauge, Back Mount TA Decal, PSI TA Ball Valve Manifold Mount TA620352B 1 NOT SHOWN Ball Valve Manifold Mount TA620353B 1 NOT SHOWN SUMP VALVE HANDLE MOUNTING ITEM DESCRIPTION PART NO. QTY Sump Valve Handle Asy TA Handle Kit (Includes Items 1b,1c,1d,1f) a Sump Valve Handle TA640096B 1 1b U-Joint Tube TA620390B 1 1c Vinyl Bushing 3/8 ID x 5/8 OD x 1/4 TA d Bar, 1/2 Dia. x 29 5/8 TA620388B 1 1e Capscrew 1/4-20UNC x f Locknut 1/4-20UNC Rubber Grip (includes Items 1) TA Capscrew 1/4-20UNC x Lock Washer 1/ Hex Nut 1/4-20UNC

16 COMMAND CENTER MOUNTING ITEM DESCRIPTION PART NO. QTY. NOTES 1 Command Center, Shield Weldment TA640055B 1 2 Command Center, Mounting Plate TA640084B 1 3 Capscrew 3/8-16UNC x 1 1/ Grade 5 4 Lock Washer 3/ Hex Nut 3/8-16UNC Capscrew 1/4-20UNC x 3/ Grade 5 7 Locknut 1/4-20UNC Capscrew 3/8-16UNC x Stainless Steel 9 Lock Washer 3/8 TA Flat Washer 3/8 TA Command Center Decals TA Decal, Shield & Power Source TA

17 COMMAND CENTER BREAKDOWN ITEM DESCRIPTION PART NO. QTY 1 Command Center TA640083B 1 2 Finishing Plug TA Capscrew 1/4-20UNCx5/ Flat Washer 1/ Hex Nut 1/4-20UNC " Ball Valve, w/mount TA " Ball Valve, Valve #1 TA " Valve Mounting TA Elbow, 1" Manifold x 1" Hose Barb TA " Gasket TA " Manifold Clamp TA " Ball Valve, w/mount TA " Ball Valve, Valve #2 TA " Valve Mounting TA620369B Elbow, 1" Manifold x 1" Manifold TA Adapter, 1" Manifold x 1" Manifold TA Tee, 1" Manifold x 1" Manifold x 1" Manifold TA Plug, 1" Manifold TA Tee, 2" Manifold x 2" Manifold x 1" Manifold TA Elbow, 2" Manifold x 1.25" Hose Barb TA Elbow, 2" Manifold x 2" Hose Barb TA /2" Ball Valve w/mount TA /2" Ball Valve Valve #4 TA /2" Valve Mounting TA620368B 1 17 ITEM DESCRIPTION PART NO. QTY Elbow, 2" Flange x 1 1/2" Hose Barb TA Elbow, 2" Flange x 2" Hose Barb TA Plug, 2" Manifold (w/out Rinse Opt.) TA " Gasket TA " Gasket TA Clamp, 1" Manifold TA Clamp, 2" Manifold TA " Ball Valve w/mount TA " Ball Valve w/valve #5 TA " Ball Valve Mounting TA620367B Elbow, 2" Male Threaded x 2" Hose Barb TA Elbow, 2" Male Thrd x 2" Female Coupler TA Quick Fill Stop Cap TA #12 Jack Chain, 29# Limit TA A/R

18 LINE STRAINER FITTINGS ITEM DESCRIPTION PART NO. QTY 1 Drain, 1" Standard TA Elbow, 1" Manifold x 1" Hose Barb TA " EPDM Gasket (NOT SHOWN) TA " Worm Screw Clamp (NOT SHOWN) TA AGITATION FITTINGS ITEM DESCRIPTION PART NO. QTY 1 Drain, 1" Standard TA Elbow, 1" Manifold x 1" Manifold TA Ball Valve w/ 1" Flange TA Ball Valve w/bracket TA Adapter, 1" Manifold x 1" Hose Barb TA " EPDM Gasket (NOT SHOWN) TA " Worm Screw Clamp (NOT SHOWN) TA

19 QUICK FILL & TANK DUMP FITTINGS ITEM DESCRIPTION PART NO. QTY 1 Ball Valve 2" Flange x 2" Male Adapter TA " Coupler Cap TA " Total Drain TA " Manifold Tee TA " Manifold x 2" 90 Hose Barb TA " EPDM Gasket (NOT SHOWN) TA " Worm Screw Clamp (NOT SHOWN) TA INTERNAL FITTINGS ITEM DESCRIPTION PART NO. QTY 1 2" Vent Cap TA Poly Reducer Bushing /2 NPTF MALE TA x 3/4-14 NPTF FEMALE 3 Nylon Jet Agitator TA Agitator Tee TA

20 SUMP FITTINGS ITEM DESCRIPTION PART NO. QTY. NOTES 1 2" Total Drain TA Mesh Screen TA " Manifold Coupling x 90 TA " Flange x 2" Flange x 2 " Flange - 3 Way Valve TA " Manifold Plug TA " Manifold Tee TA " Manifold x 2" Barb Connection TA " EPDM Gasket (NOT SHOWN) TA " Worm Screw Clamp (NOT SHOWN) TA (December 2012)

21 STRAINER ITEM DESCRIPTION PART NO. QTY. NOTES Strainer Complete TA Strainer Head TA Screen, 50 Mesh (Red) TA Gasket, EPDM TA Bowl, Polypropylene TA O-Ring, Viton TA Cap, Polypropylene TA

22 CONTROL SYSTEM - 45' THROUGH 80' X-FOLD BOOMS NOTE: FOR 80 & 90 FRONT-FOLD BOOMS REFER TO MANUAL # NOTE: FOR 60 FRONT-FOLD BOOMS REFER TO MANUAL # * * * ITEM DESCRIPTION PART NO. QTY 1 Strainer Complete TA Ball Valve Asy (3 Section-Std) TA Regulating Valve, 1" (440) TA Flowmeter TA Tubing, Gauge - 1/4" TA Ball Valve Harness TA Battery End TA Battery Cable, Special TA Ball Valve Bracket TA620391B " EPDM Gasket TA " Worm Screw Clamp TA Adapter 1" Flange x 1" FPT TA " Worm Screw TA " EPDM Gasket TA Elbow 1" Flange x 1" HB TA ITEM DESCRIPTION PART NO. QTY Remote Control System Includes Items (Not Shown) TA Regulating Valve (K-30) TA Console TA Power Cable TA Extension Cable TA Valve Cable (744-3) TA Valve Cable, Special TA Male Connector, 4-Pin TA Female Pin TA Hex Nut 1/4-20UNC Lock Washer 1/4" U-Bolt 1/4-20UNC TA Elbow 1" Flange x 3/4" HB TA *USED WITH MANUAL CONTROLLER 22

23 WHEELS & TIRES ITEM DESCRIPTION PART NO. QTY. FIG. A Single Wheels - 45 & 60' Booms Only 1 Wheel/Tire Asy - 38 x 12-8 Hole Yellow / 13.6 x Ply R-1 TA FIG. B Single Wheel - All Boom Sizes 2 Wheel & Tire Asy - 16 x Hole Yellow / TL18.4R38A 2-Star R Wheel & Tire Asy - 10 x Hole Yellow / TL320/90R46A R Wheel & Tire Asy - 13 x Hole Yellow / TL14.9R46A 8-Star R Reinforcing Ring 14442Y 2 7 Capscrew 7/8-14UNF x 3 1/2 (Grade 8) FIG. C Dual Wheels - 30" Rows 5 Wheel & Tire Asy - 10 x Hole Yellow \ TL12.4B42A 10 Ply R Capscrew 7/8-14UNF x 3 1/2 (Grade 8) " Hub Extension 16382Y 20 FIG. D Dual Wheels - 22" Rows 5 Wheel & Tire Asy - 10 x Hole Yellow \ TL12.4B42A 10 Ply R " Hub Extension 16383Y 2 10 Capscrew 7/8-14UNF x 5 (Grade 8) ALL TIRES 11 Valve Stem A/R 12 Locator Bolt

24 ADJUSTABLE AXLE MOUNTING WITH HUB & TIRE ITEM DESCRIPTION PART NO. QTY. NOTES & 800 Adjustable Axle TA640008B 1 2 Diamond Axle TA w/80-8 "Heavy" Hub Asy 3 Axle Adjuster TA620139B Bolt Hub - 2 See Page Bolt Hub - 2 See Page 26 6 Wheel & Tire Assembly - 2 See Page 23 7 Hub Bolt, 5/8-18UNF x 1 3/8 TA Grade 5 8 Capscrew 5/8-11UNC x 2 1/ Grade 5 9 Lock Washer 5/8" Hex Nut 5/8-11UNC Capscrew 3/4-10UNC x Grade 8 12 Lock Washer 3/4" Hex Nut 3/4-10UNC Axle, Zero-Offset B 2 15 Capscrew 5/8-1UNC x Grade 5 16 Lock Washer 5/8" Hex Nut 5/8-11UNC

25 60" & 120" RIGID AXLE MOUNTING WITH HUB & TIRE ITEM DESCRIPTION PART NO. QTY. NOTES & " Rigid (High-Low) Axle TA " Rigid (High-Low) Axle TA Rigid (High-Low) Axle Spindle Assembly TA640090B Bolt Hub See Page 27 5 Wheel 38x12 (8 Hole) TA Wheel & Tire Assembly TA Hub Bolt 5/8-18UNF x 1 3/8 TA Grade 5 8 Capscrew 3/4-10UNC x 2 1/ Grade 5 9 Lock Washer 3/ Hex Nut 3/4-10UNC Capscrew 3/4-10UNC x Grade 8 12 Hub & Spindle Assembly TA Includes Items 3 & 4 25

26 10-BOLT HUB ASSEMBLY WITH 3.75" SPINDLE ITEM DESCRIPTION PART NO. QTY NOTES Hub Complete & Spindle Assembly B 1 1 Seal (37605SA) Inner Bearing Cone (HM218248) Inner Bearing Cup (HM218210) Bolt Hub Sub Asy B 1 Includes Items 3 & 5 5 Outer Bearing Cup (HM212011) Outer Bearing Cone (#HM212049) Spindle 3.75" Dia. x 17 1/ Hardened Spindle Washer 4" OD Cotter Pin 3/8" Dia. x Castle Nut 2-12UNF Grade 5 11 Hub Cap =Black= 92465B 1 12 Capscrew 5/16-18UNC x 1/ Grade 5 26

27 8-BOLT HUB ASSEMBLY WITH 3.00" SPINDLE ITEM DESCRIPTION PART NO. QTY NOTES Hub Complete (80-8) TA580418G/R Beginning with the 1st unit to 01/01/ Seal (CR27394) Inner Bearing Cone (JLM506849) Inner Bearing Cup (JLM506810) Bolt Hub Sub Asy TA Includes Items 3 & 5 5 Outer Bearing Cup (LM501310) Outer Bearing Cone (LM501349) Spindle Washer 1" ID (# ) Cotter Pin 1/4" Dia. x 2 1/ Spindle/Slotted Hex Nut 1-14UNS Grade 2 11 Dust Cap 9442G/R 1 12 Lug Bolt 5/8-18UNF x 1 3/8 TA Grade 5 ITEM DESCRIPTION PART NO. QTY NOTES Hub Complete (80-8 HD) TA580479B Beginning with 01/01/1999 to Serial# B & B to Current 1 Seal (CR28700) TA Inner Bearing Cone (JLM508748) Inner Bearing Cup (JLM508710) Bolt Hub Sub Asy TA500744B 1 Includes Items 3 & 5 5 Outer Bearing Cup (LM501310) Outer Bearing Cone (LM501349) Spindle Washer 1" ID (# ) Cotter Pin 5/32" Dia. x 1 3/ Spindle/Slotted Hex Nut 1-14UNS Grade 2 11 Dust Cap 9442B 1 12 Lug Bolt 5/8-18UNF x 1 3/8 TA Grade 5 ITEM DESCRIPTION PART NO. QTY NOTES Hub Complete (75-8B) 91910G/R Beginning with Serial# B to B Seal (CR27394) Inner Bearing Cone (JLM506849) Inner Bearing Cup (JLM506810) Bolt Hub Sub Asy 95439G/R 1 Includes Items 3, 5, & 12 5 Outer Bearing Cup (LM501310) Outer Bearing Cone (LM501349) Spindle Washer 1" ID (# ) Cotter Pin 1/4" Dia. x Spindle/Slotted Hex Nut 1-14UNS Grade 2 11 Dust Cap 9442G/R 1 12 Stud Bolt 5/8-18UNF x 2 1/ Grade 8 27

28 SERIAL NUMBER B & HIGHER SIGHT GLASS MOUNTING ITEM DESCRIPTION PART NO. QTY. NOTES Sight Glass Kit Sight Gauge Weldment B 1 2 Decal, Volume Indicator Sight Gauge Tube Sight Gauge Tube Cap Breather 3/8 NPT Bronze Plastic Tie Coupler 1 1/2 PVC Reducer 1 1/2 PVC x 1/2 FPT Indictor Ball, Rod - 1 1/4" /8" EPDM Hose TA A/R Specify in Feet Elbow 1/2-18 M x 3/8 Hose Barb TA Adapter 3/8-18 M x 3/8 Hose Barb TA Cose Clamp TA Stainless Steel 14 Reducer 3/4 NPT - 3/8 NPT TA Hex Nut 1/4-20UNC Lock Washer 1/ Flat Washer 1/ U-Bolt 1/4-20UNC TA

29 SIGHT GLASS MOUNTING SERIAL NUMBER B & LOWER CHECK HOLE PERIODICALLY TO MAINTAIN UNOBSTRUCTED AIRFLOW NOTE: LEAVE THE CENTER BOLT, WASHER & NUT FASTENED WHILE INSTALLING ITEM #2. (THIS ENSURES THE PLUMBING DOOR REMAINS IN POSITION.) ITEM DESCRIPTION PART NO. QTY. NOTES Sight Glass Assembly TA U-Bolt 1/4" TA Sight Glass Holder TA620385B 1 3 Sight Glass Brace TA620386B 1 4 Level Indicator TA /4" Double Threaded Tank Fitting TA Hose Barb 3/4 x 3/4 TA Poly Pipe Cap, 3/4 TA Straight 3/4 MPT x 3/4 Hose Barb TA Capscrew 1/4-20UNC x 3/ Locknut 1/ /4" Dia. EPDM Hose - 50" TA A/R Specify in Feet 12 3/4" Dia. Clear Vinyl Tubing /2" TA A/R Specify in Feet 13 Hose Clamp, SC12 TA

30 OPTIONAL SPEED SENSOR KIT ITEM DESCRIPTION PART NO. QTY. NOTES Speed Sensor Kit TA Includes Items Speed Sensor w/ 36' Cable TA Magnets (Red) TA Magnets (Black) TA Hose Clamp Magnet TA Hose Clamp, Extra TA Bracket - 10 Bolt Hub Capscrew 3/8-16UNC x Lock Washer 3/ Speed Sensor w/36' Cable TA Cable, Speed Sensor - 10' TA Magnet ' Extension Sensor Cable TA Magnets (For Tandem Axle Assembly ONLY) TA Not Shown Cable Ties TA (December 2012)

31 1. MAGNET INSTALLATION SPEED SENSOR INSTALLATION IF SPRAYER HAS BIG WHEEL SINGLE AXLE: Use the two red hose clamp magnets, the two black hose clamp magnets and the four extra hose clamps to make an assembly as shown in Fig. 1. Mount this assembly to the sprayer wheel as shown in Fig. 2. Tighten all hose clamps securely and evely for system to work properly. Magnets must be equally spaced. Fig. 1 Fig. 2 31

32 SPEED SENSOR INSTALLATION 2. SPEED SENSOR SWITCH INSTALLATION a. Mount the speed sensor switch to the mounting bracket as shown in Fig. 5. Adjust the switch so that clearance between the magnet assembly and the switch is 1/4 to 1/2 b. Route cables out of the way and secure with plastic wire ties. c. Use cuation when adusting axle spacing not to pinch or harm cables. Fig. 5 32

33 TANK FITTINGS/FUNCTIONS 33

34 DECALS 34

35 DECALS 1100 PARTS MANUAL Introduction PART NO. DESCRIPTION QTY Refl ector, AMBER 2 TA Decal, Front 2 TA Decal, Rear Decal, TA Logo (T-Tank Sides) 2 TA Decal, TA Logo (Frame) 2 TA Decal, TA Logo (Foam Marker, Tank) 1 TA Decal, TA Logo (Clean Water, Tank) 1 TA Decal, IMPORTANT (ACE Pump) 1 TA Decal, DANGER (Shield Missing) 1 TA Decal, DANGER (PTO Shaft) 1 TA Decal, CAUTION (PTO Shield) 1 TA Decal, WARNING (Drawbar) 1 TA Decal, WARNING (PTO) 1 TA Decal, TA Logo 1 TA Decal, PSI 1 TA Decal, Command Center 1 TA Decal, Shield & Power Source Decal, Grease Daily 4 80' X-FOLD BOOM PART NO. DESCRIPTION QTY TA Decal, Height Indicator 1 TA Decal, Tail Light Instructions 2 60' X-FOLD BOOM PART NO. DESCRIPTION QTY Decal, Grease Daily 8 TA Decal, CAUTION (Weights) 1 TA Decal, TA Logo 2 TA Decal, Tail Light Instructions 2 60' FRONT-FOLD BOOM PART NO. DESCRIPTION QTY Decal, Grease Daily 8 TA Decal, DANGER (Boom Unfolding) Fluorescent Strip, Red-Orange Refl ector, RED 2 TA Decal, Keep Hands Clear 2 TA Decal, TA Logo 2 TA Decal, Tail Light Instructions Refl ector, AMBER 4 TA Decal, TA Logo 3 35

36 L:\Pagemaker_OM_Files\OMShellRock\Sprayer\\TA \\\DECEMBER