Ice Pro DB1000 Series Automatic Ice Bagging and Dispensing System

Transcription

1 Ice Pro DB000 Series Automatic Ice Bagging and Dispensing System Order parts online Installation, Operation and Service Manual Following installation, please forward this manual to the appropriate operations person. 80 Church Lane Easton, PA 800, USA Toll free (877) (60) R

2 Table of contents Welcome to Follett Corporation Important cautions Specifications Installation Door entry Locating unit Leg extension accessory Leveling Utility connections Foot pedal Bag wicket Sanitize Icemaker Adjustments Cleaning and sanitizing Exterior care Interior care Semi-annual cleaning Operation How the dispenser works System overview Control functions Bag pins installing wickets Adjusting bag stand height Using Totes or other containers Using SmartCART or other mobile ice storage devices Removing bag stand Service Agitator removal Wiring diagram Troubleshooting guide Replacement parts

3 Welcome to Follett Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that you take a moment to review this manual before beginning the installation of the dispenser. Should you have any questions or require technical help at any point, please call our technical service group, (877) or + (60) Before you begin After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing of a claim, if necessary. Check your paperwork to determine which model you have. Follett model numbers are designed to provide information about the type and capacity of Follett ice dispensing equipment. Following is an explanation of the different model numbers in the DB000 series. DB000SA SA = Semi-Automatic ice dispensing and bagging lbs maximum bin capacity DB Dispensing bin - 0/60 Hz EDB Dispensing bin - 0/50 Hz! Important cautions Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If access to this area is required, power to unit must be disconnected first. Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition. Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice. Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord(s) and plug(s) and follow the appropriate wiring diagram. Dispenser can accommodate most cube/cubelet ices up to " square or Chewblet ice (made by Horizon ice machines). Crushed, flake, or nugget ice cannot be used. Use of these ices can jam dispenser and void warranty. For questions about ice compatibility, call Follett s customer service group toll free at (877) or + (60) Always disconnect power before cleaning or servicing the dispenser. Failure to remove all sanitizer may result in health hazard.

4 Specifications Electrical Each icemaker and dispenser requires separate circuit. Equipment ground required. Standard electrical - 0V, 60Hz, phase, Max. fuse 5 amps, 5 amp circuit. Cord and plug provided. Plumbing Drain " PVC FPT for hopper drain Note: Drains should be hard piped and insulated. Maintain at least /" per foot (cm per cm run) slope on drain line run Clearance and access information Door entry Installation sites must have an unobstructed path to installation location with door openings no less than.5" (870mm) Service Clearance A minimum of " (05mm) to left of unit is necessary for service Ice type Dispenser can accommodate most cube/cubelet ices up to " square or Chewblet ice (made by Horizon ice machines). Crushed, flake, or nugget ice cannot be used. Use of these ices can jam dispenser and void warranty. For questions about ice compatibility, call Follett s technical service group toll free at (877) or + (60) Icemaker weight limit Icemaker(s) mounted on thin top may not exceed 800 lbs (6kg) Icemaker(s) mounted on thick top may not exceed 00 lbs (590kg) Container sizes Standard unit accommodates bag sizes up to 0 lbs (9kg) / 7.5" (696mm) Standard dispense chute compatible with carts and containers up to 9.5" (750mm) high Optional 6.5" (66mm) leg extension kit may be purchased to allow for up to 6" (95mm) high carts and bags up to 0 lbs (8kg) and.85" (860mm) high Bag pins Bag pins may be adjusted to accommodate bag hole centers from 5" (7mm) to 0" (5mm)

5 Dimensions and clearances Front view 5.0" (mm) Side view 5.5" (56mm) " (05mm) Service Clearance " (788mm) max. cart 7.5" (695mm) max. bag 7.75" (8mm) 7" (8mm).5" (57mm) " FPT drain " (86mm) 6.75" (88mm) 9.5" (mm) " FPT drain Notes Special top required for icemakers weighing more than 800 lbs (6kg). Adds an additional.5" (5mm) to height. Contact factory. Add " (5mm) to depth and 0 lbs (.5kg) to shipping weight when drain pan accessory used. 5

6 Installation Door Entry Some disassembly may be necessary to gain access through door openings with a width of.5" (850mm) to 5.5" (56mm). Note: Disassembly is NOT necessary for gaining entry through door openings larger than 5.5" (56mm). Remove lower splash panel with four screws (Fig..). Fig.. Detach the following plugs from the left side of control box: a) Window interlock J6 (Fig..) b) Control J (Fig..) c) PCB power J (Fig..) d) Auger motor J (Fig..) (model DB000SA only) Fig. WINDOW INTERLOCK J6 FOOTSWITCH J7 CONTROL J PCB POWER J AGITATION MOTOR J AUGER MOTOR J. Remove control panel cover by lifting and detaching hook and loop tape (Fig..).. Remove lower cover with two thumbscrews, one from each side (Fig..). Fig. 6

7 5. Remove transfer case with two latches (Fig..). 6. Remove ice deflection plate by lifting up (Fig..). 7. Remove auger by lifting up (Fig..). 8. Remove auger tube by lifting up. Note position of locating slot on lower end for reinstallation (Fig..). Fig. 9. Remove blower duct by loosening thumb screw, rotating clip (Fig. 5.) and lifting up (Fig. 5.). Fig Remove control box/fan motor mounting assembly with two screws (Fig. 6). Fig. 6 7

8 . Remove auger motor bracket with 8 screws (Fig 7).. Remove bag pin bracket with two thumbscrews (Fig. 7). Fig. 7. The unit's width may be further reduced by removing the upper ice storage section (Fig. 8). This reduces unit width by.75" (5mm) to an overall width of " (86mm). a) Remove window. b) Pull window interlock switch cable through wire trough in upper right corner of base (Fig. 8.). c) Cut tie wrap. d) Release latch from each side of ice storage section (Fig. 8.). e) Lift upper ice storage section from base. Fig. 8 Note: Reinstallation of auger tube requires locating slot be in the 7 o clock position and upper end of auger be flush to auger motor bracket. 8

9 Locating unit A minimum of " (05mm) to the left of the unit must be unobstructed for service clearance (see dimensions and clearances). Leg extension accessory. Raise unit off feet.. Remove each standard foot channel with four carriage bolts (Fig. 9.).. Remove foot insert and cap insert from standard foot channel.. Align each accessory extension foot channel to the eight holes of leg.. Use the four carriage bolts removed in step and four carriage bolts supplied with leg extension accessory to attach each extension channel to the eight holes of each leg (Fig. 9.). 6. Place foot insert and cap insert into extension foot channel. 5. Verify each leg is in fully retracted position prior to lowering unit on feet. 6. Follow leveling instructions below. Fig. 9 Leveling Leveling the unit is important for the proper operation of any top mounted icemaker. The dispenser is shipped with the legs in the fully retracted position. Each leg may be adjusted independently by turning clockwise to lower the leg or counterclockwise to raise the leg. Fig. 0 Utility connections Drain Drain connection is made to the " FPT PVC fitting (Fig. 0). Leave a minimum of /" per foot (cm per cm run) slope on drain line run. Insulate the entire run length to prevent condensation from forming on outside of drain line " (6mm) Note: Avoid excessive tightening force when connecting to this fitting..875" (58mm) drain Note: Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt threads in plastic drain. Electrical Make electrical connections in accordance with local and NEC codes. Each icemaker and dispenser requires separate circuit. Equipment ground required. Standard electrical 0V, 60Hz, phase. Max. fuse 5 amps, 5 amp circuit. Cord and plug provided. Foot pedal The foot pedal is installed to the dispenser at the factory. Remove packaging and place on floor near bag stand on front of dispenser. 9

10 Bag wicket Note: Bags must be placed behind rear stainless chute.. Move chute lever to down position (Fig..).. Transfer bags from wicket to bag pins by removing cardboard backing and sliding 5 to 0 bags onto pins at a time until posts are full (Fig..).. Return chute lever to up position (Fig. ). Sanitize Follow cleaning and sanitizing instructions. Fig. Icemaker Follow icemaker manufacturer s recommendations for installation. Note: Icemaker(s) mounted on thin top may not exceed 800 lbs (6kg). Icemaker(s) mounted on thick top may not exceed 00 lbs (590kg). Fig. Adjustments The installer should make the following initial adjustments to ensure proper operation of the dispenser. Bagger starter kit (DB000SA models only) The Ice Pro model DB00SA includes 50 bags.. Begin using the bags by locating the bagger starter kit and following the the instructions for bag wicket on page 0.. Follett recommends ordering new replacement bags immediately and confirming delivery date. Fig. Bag stand The bag stand platform may be raised or lowered to accommodate multiple bag sizes (Fig. ). The bottom of bags should touch platform when adjustment is complete.. Lift bag stand platform up and out of receiving slot on bag stand base.. Insert bag stand platform in and down into next receiving slot above bottom of bag. Dispense duration (model DB000SA only) In timed mode, the dispense duration dial of the control panel adjusts the length of time the unit dispenses ice.. Rotate dial clockwise to lengthen dispense duration. Rotate counterclockwise to shorten dispense duration.. Verify timed mode is selected.. Press start button to test length of duration. Adjust as necessary. 0

11 Review operation procedures with appropriate operations person. Give manual to appropriate operations person. Cleaning and sanitizing Solution A Cleaning solution: Fig. Combine oz (0ml) bleach with gal (8L) hot water or use an equivalent sanitizer and mix for 00 ppm. Solution B Sanitizing solution: Combine / oz (7ml) bleach with gal (8L) hot water or use an equivalent sanitizer and mix for 50 ppm. Cleaning brush A cleaning brush is included with the Ice Pro it should be mounted for easy access on either side of the bin in the bracket provided. Exterior care The stainless steel exterior of the bin can be cleaned with a stainless cleaner such as M Stainless Steel Cleaner & Polish or equivalent. Fig. 5 Interior care The polyethylene liner should be cleaned and sanitized periodically with cleaning solution prescribed below. Recommended semi-annual cleaning (every 6 months). Disconnect power from ice machine and dispenser.. Remove all ice from storage area.. Remove ice storage window (Fig..).. Remove control panel cover by lifting and detaching latch and loop tape (Fig..). 5. Remove transfer case with two latches (Fig. 5.). 6. Remove ice deflection plate by lifting up (Fig. 5.). 7. Remove auger by lifting up (Fig. 5.). 8. Remove auger tube by lifting up. Note position of locating slot on lower end for reinstallation (Fig. 5.). 9. Remove blower duct by loosening thumb screw, rotating clip and lifting up (Fig. 5.5). 0. Remove ice chute assembly (Fig. 5.6).. Remove drain pan from bag stand (Fig. 5.7).. Clean all components and bin storage surfaces with supplied brush and Solution A. Rinse thoroughly with clean water. Sanitize all components and bin storage surfaces with Solution B.. Pour a solution of one cup (8oz/7ml) household bleach mixed with one gallon (.8L) hot water into drain to help prevent algae growth in drain lines

12 Operation How the dispenser works Follett s Ice Pro bagging and dispensing system is available in manual or semi-automatic ice dispensing and bagging configurations. The semi-automatic model includes a blower to puff bags open for high volume, handsfree dispensing, bag holder pins for use with wicketed bags and programmable dispense timer. Ice is stored above a dispense auger in the dispenser storage area. An automatic agitation cycle keeps the ice from congealing by periodically activating the agitator. When the start button is pressed, the dispense motor is activated. This causes the auger assembly in the storage area to move ice to the dispense chute where it drops by gravity into a container. System overview Window locks Prevents unintended access to ice storage area Window interlock switches Shuts unit off when window is removed Control panel See detailed description on next page Chute lever Positions chute lever in up position (A) when bagging or down position (B) to load containers or carts Foot pedal Starts dispensing in manual mode. Use for topping off bags and containers in timed mode. Power switch System ON/OFF Stand assembly (DB000SA only) Drain pan may be removed to empty water or to adjust bag height. Stand should support bottom of bag. Stand support may be removed for cart filling. Bag pins (DB000SA only) Bags must be placed behind rear stainless chute. Move chute lever to down position (B). Transfer bags from wicket to bag pins by removing cardboard backing and sliding bags onto pins. Return chute lever to up position (A).

13 Control functions Model DB000SA Semi-automatic ice bagging and dispensing system controls. Open bag Press to turn on blower. Automatically blows open one bag at a time Press again to turn blower off. Blower automatically turns off after 0 minutes.. Adjust time Press +/ to change timed dispense duration in seconds - maximum time: 0 seconds. Dispense ice Press Timed once to dispense automatically. Hold Manual to top off bag or fill other containers Stop Press to stop timed dispense Model DB000 manual ice dispensing system controls Start Hold down to dispense Power switch Note: Do not turn power OFF during normal operation. Turning power OFF disables agitation cycle which may lead to congealed ice and damage to dispenser that may void warranty. DO NOT TURN POWER OFF DURING NORMAL OPERATION

14 Bag pin installing wickets (Model DB000SA only) Note: Bags must be placed behind rear stainless chute.. Move chute lever to down position (Fig. 6.).. Transfer bags from wicket to bag pins by removing cardboard backing and sliding 5 to 0 bags onto pins at a time until posts are full (Fig. 6.).. Return chute lever to up position (Fig. 7). Adjusting bag stand height (Model DB000SA only) The bag stand platform may be raised or lowered to accommodate multiple bag sizes (Fig. 8). The bottom of bags should touch platform when adjustment is complete.. Lift bag stand platform up and out of receiving slot on bag stand base.. Insert bag stand platform in and down into desired receiving slot on bag stand base. Fig. 6 Fig. 7 Using Totes or other containers The bag stand platform can accommodate containers of up to 9.5" (750mm) high.. Adjust bag stand height per instructions above.. Position chute lever in down position (Fig. 6.).. Place container below dispense chute.. Press START. Fig. 8 Using SmartCART or other mobile ice storage devices The bag stand platform must be removed to correctly position SmartCART under chute.. Remove bag stand per instructions below.. Position chute lever in down position.. Roll SmartCART under dispense chute.. Press START. Removing bag stand (Model DB000SA only). Lift bag stand platform up and out of receiving slots on bag stand base (Fig. 9.).. Lift stand up and out of receiving slots on dispenser base (Fig. 9.). Fig. 9

15 Service Agitator removal. Remove all ice from dispenser.. Disconnect power to dispenser and icemaker.. Remove window from upper ice storage section.. Remove connection pin from left side of agitator bar (Fig. 0). 5. Move agitator bar toward left dispenser wall (Fig..) while pulling out the right side from bearing (Fig..). 6. Push right side of agitator bar toward rear right corner of bin (Fig..) while pulling out the left side from the drive shaft (Fig..). 7. Position pin end of agitator in window frame and spiral clockwise out opening (Fig ). Fig. 0 Fig. Fig. Fig. 5

16 G 5 TB-6 K-D 6 9 K INTERLOCK RELAY Wiring diagram Serial Number D5557 and below /9 /8 /7 M /8 /9 /7.5 HP AUGER TB- MG INVERTER MG INVERTER P P P FS R P P P9- P9- R AUGER CW R SPEED AGITATOR.7K SPEED CONTROL TB- TB- MAIN CONTROL / HP AGITATION FS R P P8- P8- L S K-C 7 A B J-5 J- J- J- J- J- J-6 J-7 J-8 J-9 P- P-5 P- P- P- P- P- P-6 P-7 P-8 P-9 U L W V Semi-automatic models only Semi-automatic models only M F 0A F 0A F7 A F8 A L F5 /A TB- TB- PC BOARD REF. D F6 /A J7 RS OPERATOR CONSOLE INPUT 0VAC J6- P6- J6- P6- J7- J7- P7- P7- J5- J5- J5- P5- P5- P5- S9 WINDOW L S0 WINDOW R BLK BLK BLK BLK S DISPENSE FOOT SWITCH J- M BLOWER GRN J5 J9 BRN J6 J8 BLK J J7 WHT BLK WHT BLK BLK WHT J J J J J J5 J6 USER INTERFACE CONTROL WHT J BLU J8 ORG J9 YEL J0 VIO J S5 START S6 STOP Semi-automatic models only J- P- P- P- J- P- J- P- J- P- P- P- J- J- J- J- TB- F 0A F 0A BLK WHT RED BLK WHT RED U W V L L WHT GRN WHT GRN GRN BLK BLK L 6

17 7 6 Wiring diagram Serial Number D5558 and above DB000 - ICE PRO SCHEMATIC DB000SA - ICE PRO SCHEMATIC OPERATOR INTERFACE PB6 BAG OPEN START/STOP LED BLOWER MOTOR ON INDICATOR 6.0 PB5 TIMED MODE INCREASE PB TIMED MODE DECREASE PB TIMED MODE START/STOP PB TIMED MODE STOP PB MANUAL START/STOP DB000SA 6 BLK 7 BLK UPPER OPERATOR CONSOLE BOX DB000 START/STOP 5 GRN/YEL CONTROL BOARD BLOWER MOTOR SA VERSION J J SAFETY AMP PIN J GND M 6 GRN/YEL 6 WHT 6 BLK 66 GRN/YEL 65 WHT 6 BLK 0/0 VAC J J FUSE 8 AMP BLOWER MOTOR J J5 J J BLK WHT AUGER 650 FUSE 7 AMP AUG COM 000 J8 UPPER LOWER AGIT AGIT650 J9 J9 J0 J0 J J FOOT SWITCH J5 J6 BLUE BROWN ENLARGED JUMPER SETTINGS J J J0 -BLK P-6 J0 -RED P-7 J9 9-BLK P-8 J9 0-RED P-9 WINDOW SWITCH LOWER CONTROL BOX 55 RED J6 5 BLK WINDOW SWITCH 60 GRN 58 BLK J 59 WHT 5 WHT 50 BLK 5 BLU 5 BRN J J7 FOOT SWITCH 0 GRN BLK TO J- BLK TO J- 9 WHT J- 8 BLK J- 6 BLK J-5 J7-7 WHT J- J7-50/60HZ A/M X X 7 BLK 8 RED AUGER CONTROL 50/60HZ A/M X X 5 BLK 6 RED AGITATOR CONTROL P P P F S R P P P F S R FUSE BLOCK F-0A F-0A WHT F-5A BLK U V W L L U V W L L 8 WHT 7 BLK F-0A F5-0A F6-5A WHT BLK GRN 7 RED J- P- 6 WHT J- 5 BLK J- P- P- 8 GR J-5 P-5 5 BLK 6WHT AUGER MOTOR GRN 0 WHT J- RED J- P- P- 9 BLK J- P- 7 BLK GRN P- GRN-J- 8WHT AGITATOR MOTOR MAIN POWER SWITCH G WHT BLK 5 BLUE BROWN L L L-T-T7 L-T-T8 L-T-T9 T-T5-T6 M L-T-T7 L-T-T9 L-T-T8 T-T5-T6 M NEMA 6-5 Ø 0VAC INPUT 7

18 Before calling for service. Check that ice is in the dispenser and that congealed cubes are not causing a jam.. Check that circuit breaker and switches are in ON position.. Check that window is on securely. If ajar, dispenser will not operate.. Check that all drains are clear. Troubleshooting guide Symptom Ice does not dispense Bags tear off pins during filling More than one bag opens when blower is on Bags won t open. No ice in bin Possible cause. Dispense switch not closing. Foot pedal not closing. Auger motor not operating 5. Agitator motor not operating 6. Both auger motor & agitator motor not operating. Bag platform not adjusted properly. Poor quality bags. Stainless steel chute is not resting against bags. Blower switch not on. Blower duct missing or out of position. No power to blower motor Solution. Check operation of ice maker. Check for contract closure. Check for contact closure of switch inside foot pedal enclosure A. Check for power to motor B. Check for output from corresponding inverter C. Check fuses and power supply to LI & L of inverter D. Jump terminals F & S on inverter. If motor runs, replace PC board Note: Voltage from inverter and auger motor must be tested with an analog meter 5A. Check for power to motor 5B. Check for output from corresponding inverter 5C. Check fuses and power supply to LI & L of inverter 5D. Jump terminals F & S on inverter. If motor runs replace PC board Note: Voltage from inverter and auger motor must be tested with an analog meter 6A. Check that window is in place 6B. Check that both window interlock switch are fully depressed 6C. Check that interlock relay is energized. Adjust bag platform to on notch above where bottom of bag contacts platform. Try bags from another supplier. Move chute lever to up position to locate stainless steel chute in the rear position. Turn blower switch on. Reinstall/re-position blower duct. Check fuses and output power at operator control panel If problems persist after following this basic troubleshooting guide, call Follett s technical service department at (877) or (60)

19 Replacement parts Serial Number E00005 and below Reference # Description Part # Panel, access, side Latch, hopper Tensioner (includes mounting hardware) Bearing (includes mounting hardware) Sprocket, agitator (includes key) Sprocket, drive Sprocket, idler (includes mounting hardware) Frame, outer bearing support (includes () bearings, mounting hardware) Hardware, mounting, agitator motor Motor, agitator (includes mounting hardware) Leg, extension (one) (includes insert) Hardware, mounting, tensioner (set of ) Hardware, mounting, bearing (set of ) Hardware, mounting, idler wheel Key, coupling, drive Coupling, drive (includes key) Chain Bushing, bronze Shim Insert, leg 0005 Handle, insert Leg, standard (includes insert) 000 Not shown Hardware, leg mounting (set of )

20 Serial Number E00006 and above Reference # Description Part # Panel, access, side Latch, hopper Bearing (includes mounting hardware) Sprocket, agitator (includes key) Sprocket, drive Sprocket, idler (includes mounting hardware) Frame, outer bearing support (includes () bearings, mounting hardware) Hardware, mounting, agitator motor Motor, agitator (includes mounting hardware) Leg, extension (one) (includes insert) Hardware, mounting, bearing (set of ) Hardware, mounting, idler wheel Key, coupling, drive Coupling, drive (includes key) Chain Bushing, bronze Shim Insert, leg Handle, insert Leg, standard (includes insert) 000 Not shown Hardware, leg mounting (set of )

21 Reference # Description Part # Hood, dispense Cover, dispense (includes mounting hardware) Bag stand (includes () 00099) Drain pan Handle, insert Panel, access, front (includes handle) Chute, outer, dispense Bracket, bag hanger (includes () bag support pin, () t-nut, () thumbscrew) Chute, inner, dispense Actuator, chute Duct, blower (includes mounting hardware) Panel, access, side Fitting, drain 0000 Motor, auger (includes mounting hardware) Blower Shaft, pivot, inner chute (includes () cotter pins) Bracket, blower/control box Bracket, auger drive Bag stand, extended (includes () handle) Cotter pin 0889 Mounting hardware, air duct Pin, bag support 0866 Mounting hardware, dispense cover 0009 Thumbscrew T-nut 0890 Not shown Hardware, mounting, auger motor (set of ) Not shown Collar, dispense feed Not shown Screw, Nylok (8 required) Not shown Trim, window cover

22 Reference # Description Part # Tube, auger Auger 0886 Deflector, ice Plate, lower, auger drive Plate, cover, auger drive Chain, auger drive Latch, auger drive Coupling, auger motor Transmission, auger drive (includes lower plate, cover plate, chain, latch, coupling and 0006 tensioner) 0 Tensioner, auger chain 0007 Agitator, lower (includes lock pin) Agitator, upper (includes lock pin) Window, inspection (includes latch) Latch, window Catch, window Switch, safety Bearing, auger (includes mounting hardware) Bearing, agitator (includes mounting hardware) Pin, lock, agitator Cover, switch plate 0005 Hardware, mounting, agitator bearing Plate, access, agitator bearing Hardware, mounting, auger bearing (set of ) Hopper, upper section (includes inspection window and latch) Not shown Bracket, brush, hopper cleaning Not shown Brush, hopper cleaning Not shown Pole, extension, brush 00078

23 Reference # Description Part # Bearing, agitator support 0005 Kit, shaft seal, agitator (includes mounting hardware) 000 Gasket, tube seal, auger Kit, tube seal, auger (includes gasket and base seal) Base, seal Seal, agitator Collar, seal Hardware, mounting, shaft seal (set of ) Hardware, mounting, tube seal (set of 6) 0006

24 Serial Number D5557 and below Reference # Description Part # Inverter, auger 006 Inverter, agitator Terminal strip 0006 Fuse holder Fuse, 0 amp Relay Potentiometer, agitator speed Switch, rocker 08867

25 Serial Number D5558 and above 5 Reference # Description Part # Inverter, auger Inverter, agitator Fuse holder 0005 Fuse, 0 amp Switch, rocker

26 Serial Number D5557 and below DB000-SA 5 6 DB Reference # Description Part # DB000 SA Control board (green display) 0005 Control board (red display) obsolete. Use retrofit kit 0098 below. Terminal strip 000 Control knob Switch, stop Switch, start Label, console (green display) Label, console (red display) Fuse holder Cover, console (green display includes console label) Cover, console (red display includes console label) 0098 Not shown Fuse, / amp 0885 Not shown Fuse, amp 0886 Not shown Retrofit kit, control board, green display (includes console cover, control board, stop and start switches) 0098 Reference # Description Part # DB000 Control board Switch, start 000 Label, console Fuse holder 0895 Not shown Fuse, / amp Terminal strip 000 Not shown Switch, foot

27 Serial Number D5558 and above DB000-SA DB000 5 Reference # Description Part # DB000 SA Control board Control board (red display) obsolete. Use retrofit kit 0098 below. Terminal strip 000 Label, green display Fuse holder Cover, console (green display includes label) Not shown Fuse, amp 0886 Not shown Retrofit kit, control board, green display (includes cover, label, control board, start and stop switches) 0098 Reference # Description Part # DB000 Control board Switch, start 000 Label, console Terminal strip 000 Not shown Switch, foot

28 Ice Pro, SmartCART, and Totes are trademarks of Follett Corporation. Chewblet and Follett are registered trademarks of Follett Corporation, registered in the US. 80 Church Lane Easton, PA 800, USA Toll free (877) (60) R Follett Corporation /