INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Rosemary McKenzie
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. All CR-V Issue Date S P/N 08V31-S9A-115 FEB 2005 PARTS LIST 6 Washer-bolts Left fog light 6 Spring nuts Harness bracket Right fog light 2 Wire ties with clip Left trim Fog light harness Right trim Switch harness Fog light switch EPT sealer Relay Fuse label 25 Wire ties TOOL AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm and 14 mm sockets File Torque wrench Hacksaw blade Duct tape 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 08V31-S9A of 17

2 Illustration of the Fog Lights Installed on the Vehicle Installing the Fog Light RELAY 3. Open the hood. Remove the radiator cover (seven clips and one bolt). CLIPS (7: small) BOLT RIGHT T LEFT INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: These installation instruction show the left fog light begin installed. The same procedure applies to installing the right fog light. RADIATOR COVER 3N05011T 4. Remove the eight clips and four self-tapping screws that fasten the front bumper. With an assistant holding the bumper, remove the front bumper. LARGE CLIP 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. SELF- TAPPING SCREWS (2) CLIPS (6) BUMPER SELF-TAPPING SCREWS (2) T 2 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

3 5. Using duct tape, mask the bumper around the fog light opening. BUMPER 7. Get the left trim. Using the tab (marked " L") on the left trim as a reference, attach the left trim to the bumper with the "L" between the bosses on the front bumper. LEFT TRIM BUMPER Cut out. BUMPER OPENING Cut out. BUMPER DUCT TAPE LEFT TRIM BOSS LEFT TRIM M BUMPER M 6. Using a hacksaw blade, slowly and carefully cut out the fog light opening. Be sure to cut the opening as round as possible, and do not damage the bumper. Remove any burrs from the edges of the fog light opening with a file American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 3 of 17

4 8. Install the three spring nuts on the front bumper rib. BUMPER Routing the Fog Light Harness 11. Behind the left headlight, locate the fog light 1-pin connector blue-taped to the vehicle harness. Remove the blue tape to free the connector. LEFT HEADLIGHT 2-PIN (SHORT ) 2-PIN (LONG ) RIB SPRING NUTS (3) H HOLE 9. Fit the pin from the left fog light into the recess in the front bumper. Position the left fog light over the three holes in the spring nuts, and install the three washer-bolts. GROUND TERMINAL BLUE TAPE RECESS BUMPER PIN 1-PIN H 12. Get the fog light harness. Plug the fog light harness 1-pin connector into the vehicle harness 1-pin connector. Secure the 1-pin connector to the vehicle harness with two wire ties. LEFT BOLTS (3) SPRING NUTS (3) T 13. Route the fog light harness 2-pin connector (short harness), and the ground connector harness through the hole under the left headlight. 14. Route the fog light harness 2-pin connector (the one with a long harness) to the right along the vehicle harness. 10. Repeat steps 5 through 9 to install the fog light on the right side of the vehicle. 4 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

5 15. Locate and remove the vehicle ground bolt. Attach the fog light harness ground terminal to this ground bolt, and tighten the bolt securely. 18. Attach two wire ties with clip to the fog light harness at the green-taped positions, then push the clip into the holes in the harness bracket. GREEN TAPE WITH CLIP GROUND TERMINAL SIDE WIRE TIE GROUND BOLT (Reuse.) BRACKET GREEN TAPE H GROUND TERMINAL GROUND TERMINAL H 19. Remove two bolts that secure the air intake. Insert the harness bracket between the air intake and the bulkhead, then secure it with the two bolts. Secure the fog light harness to the vehicle harness with two wire ties. 16. Secure the fog light harness to the vehicle harness with two wire ties in the areas shown. 17. Route the fog light harness 2-pin connector along the vehicle harness, secure the fog light harness to the vehicle harness with two wire ties in the areas shown. AIR INTAKE BOLT BRACKET H H 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 5 of 17

6 20. Route the fog light harness along the vehicle harness through the hole in the body panel. Secure the fog light harness to the vehicle harness, and to the bulkhead upper frame with the six wire ties in the areas shown. 22. With an assistant holding the bumper, connect the two fog light harness 2-pin connectors to the left and right fog lights, then reinstall the front bumper. Do not fasten the inner fender (four clips and two self-tapping screws) to the front bumper until after the fot light aiming adjustment. BULKHEAD UPPER FRAME LARGE CLIPS Reuse. 2-PIN RIGHT BULKHEAD SIDE STAY BUMPER RIGHT BODY PANEL HOLE T CLIP Reuse. LEFT SELF- TAPPING SCREWS (2) Reuse T 21. Secure the fog light harness to the vehicle ground harness with one wire tie. Do not secure the fog light harness to the SRS harness. SRS Routing the Switch Harness 23. Remove the driver s dashboard under cover by turning the knob clockwise, and releasing one clip. HOLDER WIRE TIE T CLIP DRIVER S DASHBOARD UNDER COVER KNOB Turn clockwise of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

7 24. Remove the driver s dashboard lower cover: Remove the fuse box lid, and open the pocket. Remove the two self-tapping screws. Gently pull out on the driver s dashboard lower cover to release the eight clips. If equipped, unplug the vehicle connector and remove the lower cover. 26. Remove the passenger s dashboard under cover (release the three clips and two pins). CLIPS (3) (If equipped.) (If equipped.) DRIVER S DASHBOARD LOWER COVER HOOKS (2) PINS (2) PASSENGER S DASHBOARD UNDER COVER POCKET CLIPS (8) SELF- TAPPING SCREW FUSE BOX LID RETAINING TABS (2) CLIP H 27. Open the dashboard pocket lid. Remove the lid by releasing the two retaining clips and two retaining tabs, then remove the dashboard pocket (one selftapping screw, then pull out to release the one clip and three retaining tabs). Unplug the vehicle connector. 25. Lower the steering wheel tilt lever. Remove the upper and lower steering column covers. (two selftapping screws, one screw, and six tabs). Gently push on the six retaining tabs, and separate the two steering column covers. CLIP RETAINING TAB DASHBOARD POCKET UPPER STEERING COLUMN COVER LOWER STEERING COLUMN COVER SELF- TAPPING SCREW LID RETAINING CLIPS (2) RETAINING TABS (2) DASHBOARD POCKET LID RETAINING TABS (2) H SELF- TAPPING SCREW Push TABS (6) SCREW M 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 7 of 17

8 28. Remove two self-tapping screws that fasten the heater A/C control panel to the dashboard. Pull the heater A/C control panel out toward you to release the four clips. Unplug the vehicle connector, and remove the heater A/C control panel. SELF- TAPPING SCREW 30. On M/T vehicles only, remove the four seat track end covers from the driver s seat, then remove the four bolts that secure the seat. DRIVER S SIDE SEAT SEAT TRACK END COVERS (4) HEATER A/C CONTROL PANEL BOLTS (4) CLIPS (4) H 31. On M/T vehicle only, pull the shift boot down while holding the plastic clip. Remove the shift knob from the shift lever by turning it counterclockwise. 29. On A/T vehicles only, remove the two clips and six self-tapping screws, and pull the dashboard center lower cover out toward you to release the six clips. Unplug the vehicle 2-pin connector from the accessory socket, and remove the cover. PLASTIC CLIP SELF- TAPPING SCREWS (6) 2-PIN SHIFT KNOB Turn counterclockwise to remove. SHIFT BOOT Pull down Pull DASHBOARD CENTER LOWER COVER CLIPS (2) CLIPS (4) T CLIP 8 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

9 32. On M/T vehicle only, remove the two side covers (four tabs) from the center console. 34. Route the switch harness 5-pin connector into the instrument panel opening. 2-PIN 5-PIN CLIP ILLUMINATION BULB Pull SIDE COVER TABS (4) INSTRUMENT PANEL OPENING T CONSOLE SIDE TABS (4) COVER SELF-TAPPING SCREWS (7) CLIPS (2) CLIPS (2) T 35. Plug the relay into the switch harness relay block. Connect the relay to the relay block socket with harness. RELAY 33. On M/T vehicle only, remove the two clips and seven self-tapping screws, and pull the front console out toward you to release four clips. Unplug the 2-pin connector from the accessory socket, and remove the front console. RELAY BLOCK T 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 9 of 17

10 36. Slide the switch harness relay block onto the appropriate bracket, as shown. With Vehicle Bracket: 37. Route the switch harness along the body panel through the fuse box area, and secure it to the vehicle harness and body panel with three wire ties. BRACKET RELAY BLOCK WIRE TIE BODY PANEL T T With Vehicle Relay Block: RELAY BLOCK 38. Attach the fuse label (20A) to the switch harness fuse case. FUSE BOX 1-PIN (WHT/RED WIRE) FUSE BOX RELAY BLOCK T FUSE LABEL (20A) FUSE CASE Front View T 1-PIN LOCATION 39. Connect the switch harness 1-pin connector (WHT/RED wire) to the fuse box. 10 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

11 NOTE: If the 1-pin connector is already being used by another accessory, plug the switch harness connector into the 1-pin connector taped to the accessory harness. 41. On vehicles with a vehicle 1-pin connector on the rear of the fuse box lid: Locate the 1-pin connector blue-taped to the vehicle harness, and connect the switch harness 1-pin connector into the vehicle 1- pin connector. OTHER ACCESSORY S TAPED 1-PIN 1-PIN S 40. On A/T model vehicle, unplug the vehicle 6-pin connector from the fuse box, and connect the switch harness 6-pin connector in between. On M/T model vehicle, plug the switch harness 6-pin connector into the fuse box. FUSE BOX 1-PIN H FUSE BOX 6-PIN 6-PIN (If equipped.) 42. On vehicles with a vehicle 1-pin connector on the rear of the vehicle frame: Locate the 1-pin connector blue-taped to the vehicle harness, remove the blue tape, and free the connector. Connect the switch harness 1-pin connector to the vehicle 1-pin connector. 1-PIN 1-PIN 6-PIN 6-PIN LOCATION FUSE BOX Front View FUSE BOX T BLUE TAPE FRAME T 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 11 of 17

12 43. Route the switch harness terminal along the vehicle harness above the steering column. 47. Route the switch harness 10-pin connector toward the right between the instrument panel and vehicle frame in the area shown. TERMINAL COMBINATION INSTRUMENT PANEL HEATER CONTROL PANEL OPENING FRAME 16-PIN 44. Unplug the vehicle 16-pin connector from the combination switch T 45. Release the retainer from the vehicle 16-pin connector. Push the switch harness terminal into the appropriate slot of the 16-pin connector. 10-PIN 10-PIN AND 8-PIN S 8-PIN 10-PIN RETAINING TAB RETAINER INSERT SLOT 16-PIN TERMINAL 16-PIN Viewed from harness side TERMINAL T 10-PIN 10-PIN T 48. Unplug the vehicle harness 10-pin connector and 8-pin connector. Separate the 8-pin connector from the 10-pin connector by sliding them apart. 49. Slide the vehicle 8-pin connector onto the switch harness 10-pin connector. 46. Lock the retainer, and plug the vehicle connector back into the combination switch. 12 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

13 50. Plug the switch harness 10-pin connector and vehicle harness 8-pin connector into the vehicle 10-pin connector and vehicle 8-pin connector. Plug the other switch harness 10-pin connector into the vehicle harness 10-pin connector. Wrap one EPT sealer around the switch harness 10-pin connector. 52. On vehicles with the vehicle 1-pin connector on the rear of the fuse box lid: Continue to secure the switch harness to the vehicle harness with three wire ties. Secure the switch harness fuse case so the cap is clear of the wire ties and can be accessed. 10-PIN WIRE TIE 10-PIN AND 8-PIN S EPT SEALER FUSE CASE T 10-PIN 10-PIN 8-PIN T 53. On vehicles with the vehicle 1-pin connector on the rear of the vehicle frame: Secure the switch harness to the vehicle harness with four wire ties. Secure the switch harness fuse case on the upper side, so the fuses in the fuse box can be accessed, and so that the vehicle bracket edge does not cut into the switch harness. 51. Secure the switch harness to the vehicle harness with one wire tie in the area shown. WIRE FUSE CASE BRACKET EDGE WIRE TIE T 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 13 of 17

14 54. Along the steering column, secure the switch harness to the vehicle harness with two wire ties. 57. Connect the switch harness 5-pin connector (blue) into the fog light switch, and reinstall the driver s dashboard lower cover. (If equipped.) 5-PIN (BLUE) (If equipped.) WIRE TIE T T DRIVER S DASHBOARD LOWER COVER Installing the Switch 55. Remove the two retaining tabs, and remove the right switch lid from the driver s dashboard lower cover. LID (Discard.) 58. Check that all wire harnesses are routed properly and all connectors are plugged in. 59. Reinstall all removed parts. Check that all clips and fasteners are installed securely. Torque the driver s seat bolts to 34 N m (25 lb-ft). 60. Reconnect the negative cable to the battery. USE AND CARE DRIVER S DASHBOARD LOWER COVER RETAINING TABS (2) T How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. 56. Install the fog light switch in the driver s dashboard lower cover. 14 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

15 Fog Light Aiming Adjustment 61. Adjust the fog light: Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment gear in or out until the light is aimed correctly. BULB REPLACEMENT 1. Remove the two clips and one self-tapping screw, then pull the inner fender out as shown. AIMING ADJUSTMENT GEAR PHILLlPS SCREWDRIVER To raise To lower INNER FENDER (Pull.) 62. Install the inner fenders to the front bumper (four clips and two self-tapping screws). 63. Reset the clock, and reset the radio station presets. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 64. Start the engine. Push down on the driver s window switch until the window is fully open. 65. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds. 66. Test the driver s window AUTO function T 2. Unplug the connector and remove the bulb from the fog light. CLIP SELF- TAPPING SCREW BULB T T 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 15 of 17

16 3. Install the new bulb into the fog light and connect the connector to the new bulb. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W HB4 Halogen Light Bulb P/N SL5-A02-M2 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it with a clean, soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. NEW BULB T 4. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 5. Check the operation of the fog light; adjust the aiming if necessary. 16 of 17 AII (0502) 2005 American Honda Motor Co., Inc. - All Rights Reserved.

17 CIRCUIT DIAGRAM HOT AT ALL TIMES WHT/RED 20A WHT HOT WITH HEADLIGHT IN HEAD RED/YEL Fog Light Fuse HOT WITH HEADLIGHT IN PARK OR HEAD RED/BLK Switch 1 = Switch Illumination 2 = Indicator 1 2 RED RED/BLU Illumination Control Fog Light Relay RED/WHT BLU/RED 1 2 Dimmer Switch 1 = Low 2 = Hi Front Fog Light BLK K OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE BLU BLUE PUR PURPLE LIGHT GRN GREEN PNK PINK OFF Low Hi RED WHT RED WHITE GRY LT GRN GRAY LIGHT GREEN OFF ON ON - LT BLU LIGHT BLUE 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII (0502) 17 of 17

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176 2005 CR-V Issue Date P/N 08V31-S9A-114 SEP 2004 PARTS LIST 25 Wire ties Left fog light 6 Washer-bolts Right fog light 6 Spring