Bachmann Digital Sound Decoder Installation Notes
|
|
- Alexandra Henderson
- 6 years ago
- Views:
Transcription
1 New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital Sound Decoder into a Bachmann Locomotive. All of the components are installed inside the tender. No major mechanical modifications are needed and the entire installation should only take a few hours. A 1 speaker is installed under the coal load. The sound decoder is wired to a standard 8-pin NMRA connector and plugs into the DCC ready connector in the tender. Bill of Materials Stock No. Description DSD-090LC Digital Sound Decoder Speaker Speaker Gasket (Pack of 4) Two-pin Microconnector Heat-Shrink Tubing NMRA-type 8-Pin Header (pack of 4) Tools You Will Need Miniature Screwdriver Set X-acto Knife with #11 Blade 1-1/2 x 3 x Styrene Sheet Flat Black Paint RTV or Silicone Sealant 1/4 Drill 7/8 Forstner Bit or Spade Bit Miniature Files Wire Cutters Wire Strippers 25W Solder Iron Rosin Core Solder Heat gun Tweezers Double-sided Foam Tape Pin Vise or Electric Drill #65 Drill Bit Photo 1 Installation 1. Remove the tender shell by unscrewing the small phillips head screw on the bottom frame center, near the back of the front truck (Photo 1). Set this screw aside. Slide the front of the tender shell forward until you can slide the two tabs at the back of the tender out of their slots. 2. The coal load is a separate piece that can be removed by sliding a knife blade under the back of the load and then gently prying the plastic part loose (Photo 2). 3. With your X-acto knife, cut out a piece of 0.040" sheet styrene that measures 0.60" x 0.25". Paint this a flat black and glue over the Photo 2
2 opening at the bottom of the coal bunker using RTV. Photo 3 shows test-fitting the piece of styrene before painting. Gluing the template to the sheet styrene first makes the measuring and cutting easier. Use the spade bit to drill the large 7/8 hole (Photo 5). If you do not have access to a Forstner or spade bit, you can drill several smaller holes and trim the excess away with a hobby knife. Photo 3 4. Drill a 1/4" hole in the back of the coal bunker for the speaker wires and connector. (Photo4) Since this piece of plastic is simply glued in place, it is a good idea to make a small pilot hole first so as not to 'snag' the plastic. Drill from the bottom of the tender shell to avoid the screw boss. Photo 5 Cut and trim the outer edges. Test fit the plate in the tender. File the rear edge at a slight angle to match the back of the bunker for a perfect fit. 6. Cut approximately 2.75" from each of the purple wires on the DSD-090LC. This should leave roughly an inch of wire still attached to the decoder. Strip 1/8" of insulation from both ends of the two 2.75" lengths of wire. Tin the ends and set aside. 7. Trim the leads of the 33 uf, 16V bipolar capacitor to 1/2 (Photo 6). Photo 4 5. Create a speaker mounting plate from styrene using the template provided. Photo " Speaker Plate " Styrene 1.46" 0.66" 8. Solder one of the 2.75 purple wires you cut in Step 6 to one lead of the capacitor. Solder the other capacitor lead to one of the speaker terminals, putting a small piece of tape under the connection to insulate it from the back of the speaker. 0.60" 1.32" 0.36" 0.88" Dia. 0.68" 0.11" Photo 7
3 9. Solder the other length of purple wire to the other speaker terminal. Slide a piece of shrink tubing over your connections and shrink with a heat gun, being careful not to point directly at the capacitor. 10. Solder one speaker wire to the solder terminal of the male Microconnector (Photo 9). Solder the other speaker wire to the remaining male Microconnector terminal. Slide heat shrink tubing over both connections and shrink with the heat gun. Photo Strip and tin the remaining length of purple wire still attached to the DSD-090LC. Slide a piece of shrink tubing over each piece. Photo Peel the backing off of one side of the selfadhesive speaker gasket with a pair of tweezers. Line up the gasket with the rim of the speaker and press into place. Peel off the remaining backing from the gasket. Line the speaker up with the hole cut in the center of the speaker plate and press into place with the speaker terminals oriented toward the tab as shown in Photo Solder of these purple wires to the solder terminal of the female Microconnector. Solder the purple speaker wire to the remaining female Microconnector terminal. Slide the heat shrink tubing over both connections and shrink with the heat gun, being careful not the heat the decoder itself. 16. Following the diagram below, solder the remaining decoder wires to the 8-pin connector. Since you will not be using either the brown or yellow wires for this installation, trim these wires back to about an inch and tape the ends to the side of the DSD so they will not short to anything. Solder wires to cup side of 8-pin connector Motor Right (Orange) Rear Light (Yellow) Not Used Left Rail (Black) Photo Slide the two-pin speaker connector through the hole in the coal bunker that you drilled in Step Mount the speaker assembly in the coal bunker as shown in Photo 10. Run a bead of RTV around the edges of the mounting plate being careful not to get any on the face of the speaker. Set aside to let the RTV dry. Right Rail (Red) Function Common (Blue) Headlight (White) Motor Left Gray NOTE: If you wish to use a cam to synchronize the exhaust or use the DSD-090's lighting effects, do not cut the yellow or brown wires! The yellow wire can be used to hook up a tender backup light if you wish; connect one buld lead to the yellow wire and other to the Blue, or Funtion Common wire. The brown wire connects to your cam.) Insulate your connections. 17. Remove the dummy plug on the Bachmann PCB and plug the 8-pin connector into the
4 exposed socket. The red wire should line up with the 8 marked on the Bachmann PCB. 18. Mate the two-pin female connector on the DSD-090 to the two-pin male connector coming through the hole in the coal bunker. 15. Attach the DSD-090LC to the tender roof, on the opposite side of the tender from the 8-pin connector, with Velcro or foam tape (Photo11). Photo Before you reassemble the locomotive, inspect your work for mis-wires, shorts, broken or nicked wires. 17. Before replacing the coal load insert in the top of the tender shell, drill some small holes in the 'coal' with a #65 drill. Space your holes approximately 1/4" apart and drill holes at random angles so they will not be visible. Replace the coal load in the tender shell. 17. Replace the tender shell. Be careful that the wires are not caught between the tender shell and the frame. Replace the screw you removed in step one. Complete the connection between the locomotive and the tender by plugging in the two small orange connectors. 18. Put the locomotive and tender on the programming track and check for shorts. 17. CV Programming Most of the sounds from the DSD-090LC will not need to be changed. The default address is 3. You may wish to change the address of the decoder by changing CV1 (see your command station manual for instructions). You may wish to make adjustments to the Auto Exhaust Chuff Rate (if you have not installed a cam). Auto-Exhaust automatically generates an exhaust chuff rate proportional to the throttle setting. Since every locomotive is different, CV 116 is used to match up the Auto Exhaust rate to the locomotive speed and may be loaded with any value between 0 and 127. Higher values will yield higher chuff rates for a given throttle setting. A typical synchronization rate may be computed as: SPD CV Value = X DIA where SPD is the locomotive s top speed in scale miles-per-hour at full throttle and DIA is the locomotive s driver wheel diameter in scale inches. If you don t know your locomotive s top speed, you can also estimate it and still get pretty good results. A good rule of thumb is to use 45 MPH for freight locomotives and 70 MPH for passenger engines. Here are some suggestions for CV settings to get you on track. CV 2 Start Voltage 20 CV 112 Articulated Exhaust 129 CV 116 Chuff Rate 34 CV 115 Whistle Selection 1, 2 or 3 The LC Series Owner s Manual Software Release 2.00 is available for download at our web site ( html). This manual will give you additional information regarding CV set up and customizing the decoder for your operations.
5
Athearn Pacific Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Overview This application note describes how to install a DSD-100LC Digital Sound Decoder into the Athearn Pacific Locomotive. All of the
More informationApplication Note. Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an HO Atlas RS-3. Skill Level
More informationAtlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes
Atlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an Atlas Silver
More informationKato P42 Tsunami Digital Sound Decoder Installation Notes
Kato P42 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes the procedure for installing a TSU-KT1000 Digital Sound Decoder into a Kato HO P42 locomotive. Skill Level
More informationAthearn Genesis GP38-2 Tsunami Digital Sound Decoder Installation Notes
Athearn Genesis GP38-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 digital sound decoder into an Athearn Genesis HO GP38-2. Skill
More informationApplication Note. KATO SD40-2 Mid Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a Tsunami TSU-KT1000 Digital Sound Decoder into the HO Kato SD40-2 (Mid-production). Skill Level 2: The entire installation can
More informationApplication Note. Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes
Application Note Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into a Bachmann HO F40PH. Skill
More informationApplication Note. Walthers/Proto 2000 E7A Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-1000 digital sound decoder into a Walthers/ Proto 2000 E7A. Skill Level 2: The entire installation can be completed in one
More informationBroadway Limited (and Blueline) SD40-2 Tsunami Digital Sound Decoder Installation Notes
Broadway Limited (and Blueline) SD40-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into a HO Broadway Limited
More informationAthearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40T-2. Skill Level 2: The entire
More informationAtlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes
Atlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an Atlas HO MP-15. Skill Level 2: The entire
More informationAthearn SD40 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40. Skill Level 2: The entire installation
More informationAthearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD CF7. Skill Level 2: The entire
More informationAthearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD GP35. Skill Level 2: The
More informationAthearn RTR F59PHI Tsunami Digital Sound Decoder Installation Notes
Athearn RTR F59PHI Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 Digital Sound Decoder into an Athearn HO Ready to Roll EMD F59PHI
More informationApplication Note. Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes
Application Note Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 digital sound decoder into an Athearn Genesis
More informationApplication Note. Athearn RTR SW-1000/SW-1500 Tsunami Digital Sound Decoder Installation Notes
Application Note Athearn RTR SW-1000/SW-1500 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into the HO Athearn
More informationWalthers/Life-Like USRA Steam Locomotive
North Raleigh Model Railroad Club Installing Decoders in N Scale Locomotives Detailed Instructions Walthers/Life-Like USRA 2-8-8-2 Steam Locomotive by David Derway May 17, 2010 Table of Contents Introduction...
More informationBachmann. Climax. Phoenix Sound Systems, Inc West Liberty Road Ann Arbor MI
Bachmann Climax Phoenix Sound Systems, Inc. 3514 West Liberty Road Ann Arbor MI 48103 www.phoenixsound.com phone: 800-651-2444 fax: 734-662-0809 e-mail: phoenixsound@phoenixsound.com 2004-2007 Phoenix
More informationBachmann 38 Ton Shay
Bachmann 38 Ton Shay Phoenix Sound Systems, Inc. 3514 West Liberty Road Ann Arbor MI 48103 www.phoenixsound.com phone: 800-651-2444 fax: 734-662-0809 e-mail: phoenixsound@phoenixsound.com 2005-2008 Phoenix
More informationTip: LED Lighting Improvements for Rheingold Set Date:
Hi All, Recently I came into possession of the 41928 Rheingold set and was excited to see that I could add a function decoder to switch the light functions on and off. The first problem is Märklin don
More informationThank you for purchasing the Blackstone Models K-27!
Operations Manual Thank you for purchasing the Blackstone Models K-27! Before your Mudhen whistles off, we want to tell you about a few things that will enhance your operating experience and ensure that
More informationThese instructions show how to build the Remote Controlled Fart machine Sound Kit.
Remote Controlled Fart Machine Assembly Instructions These instructions show how to build the Remote Controlled Fart machine Sound Kit. Tools Required Drill with 7/64, 3/16, and ¼ drill bits. Holt melt
More informationBy Mark Schutzer PCR Regional Convention, San Luis Obispo May 2014 Copies of this presentation can be found at
A Beginners Guide to Installing DCC Decoders By Mark Schutzer PCR Regional Convention, San Luis Obispo May 2014 Copies of this presentation can be found at http://www.markschutzer.com Clinic Overview Installing
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationSOC-Meter Kit Building R9b
Installation The SOC-Meter fits nicely on the shelf behind the cup holders. You can also place it above the Nav, or on the dash, secured with Velcro. Before driving, carefully route the OBD cable so that
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationTip: LED Lighting for the 4367 SBB Euro City Set, 4366 and 4368 Cars Date: , Corrections Modified , Photos
Hi All, I have had the 4367 SBB Euro City set with extra cars 4366 and 4368 since 1998, apart from a test run on the layout they have stayed in storage ever since. I decided to change some rolling stock
More informationDoor panel insert trim replacement Volvo V70
Door panel insert trim replacement 1998-2000 Volvo V70 Tools needed: Torx Driver T25, Putty Knife, Bone Tool (optional), Heat gun or Dremel cutting tool, wire brush (or use a plastic tile and grout brush),
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationModeling Ideas and techniques, by Bob Rohwer What is the right DCC Decoder for my Locomotive?
Modeling Ideas and techniques, by Bob Rohwer What is the right DCC Decoder for my Locomotive? I hear this question a lot. Fortunately there are a lot of resources to answer the question. The best I have
More informationTHE MOTOR. Page 1 of 9
Page 1 of 9 The Bachmann HO Old Time 4-4-0 has been around a long time and suffers from two problems: the latest motor will burnout with a frying of the added DCC decoder and the pickup system is very
More informationCabin Light. Hi All, 1
Hi All, My friend Rudolf set me a challenge for his 36331 electric locomotive, wanting Telex couplers fitted. When I opened up the locomotive I discovered there is very little room to add extra components
More informationTsunami Digital Sound Decoder Installation Guide
Tsunami Digital Sound Decoder Installation Guide for the New User Software Release 1.00 Rev. A 11/18/05 Notice The information in this document is subject to change without notice. SoundTraxx (Throttle
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More information1. Invert the tender, and hold in a suitable device. We use a foam cradle the Peco loco service cradle being ideal.
Bachmann J11 EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationTip: LED Lighting for the 3098 Locomotive and 4392 Coach Set Date: , ,
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationInstructions for installing Extendable Replacement Mirrors for Ford HD vehicle.
Instructions for installing Extendable Replacement Mirrors for Ford HD vehicle. Manual CIPA # 82100 Right Hand #82110 Left Hand #82111 Electric CIPA # 72100 #72110 #72111 Heated / Electric CIPA # 72500
More information5 Amp Dual Mode Sound Decoder by Frank T.Verrico
5 Amp Dual Mode Sound Decoder by Frank T.Verrico Model Rectifier Corp. s latest venture into O scale is a 5 amp. dual mode, [DC/DCC], sound decoder. This full featured N.M.R.A. compatible sound decoder
More informationSound Install Steam. Presented by Tim s Trains
Presented by Tim s Trains This presentation will show you the basic steps required to install a sound decoder and speaker in a steam locomotive. This particular locomotive is a Bachmann 4-8-4 with a Vanderbilt
More informationInstalling a TCS FL4 into the Eureka CTH Ben O Malley
Please note, this modification requires soldering skill at board level and involves removing surface mount components. This modification will also void your warranty and all responsibility resides with
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationPN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide
Four panel Sequential LED Taillight kit installation guide Kit Contents: 2 tail light LED panels 2 tail light turn signal LED panels 1 rubber boot/sleeve kit 1 power wire with t-tap 1 driver side LED harness,
More informationDCC Decoders for Brass Steam Locomotives
DCC Decoders for Brass Steam Locomotives By Mark Schutzer PCR Regional Convention, Concord, CA May 2005 Copies of this presentation can be found at http://www.markschutzer.com Clinic Overview Part 3 Installing
More informationSTAY ON TRACK WITH THIS LINE FOLLOW BUGGY WITH :MOVE LINE FOLLOW BOARD FOR BBC MICRO:BIT
STAY ON TRACK WITH THIS LINE FOLLOW BUGGY WITH :MOVE LINE FOLLOW BOARD FOR BBC MICRO:BIT BUILD INSTRUCTIONS LIST OF FIXINGS M3 BOLTS M3 NUTS STANDOFFS 6mm x12 x4 x4 10mm x4 x12 12mm x2 30mm x2 20mm M-F
More informationThis year Märklin have released a coach which has included LED lighting with a currentconducting close coupler (single pole)
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationMicro-Trains #1021/#1022 Low short profile coupler
1 Micro-Trains #1021/#1022 Low short profile coupler Low short profile coupler, for locomotives and cars with limited mounting area, makes 2 pair of either (1021) Life-Like E8A Pilot or Bachmann 4-8-4
More informationAmp & Speaker Upgrade Install Instructions for Batwing Fairing
Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 10 mm Socket Phillips Screwdriver 1/2 inch Ratchet Wrench T25 Torx
More informationInstallation Guide for the Extreme Short Shaft Kit
INSTALLATION GUIDE Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz Installation Guide for the Extreme Short Shaft Kit Part #004444400
More informationEMD DD35 Powered & Dummy Units. Assembly Instructions
EMD DD35 Powered & Dummy Units Assembly Instructions Main Shell Side Handrail End Handrails Fuel Tank (Loose Part, Powered Unit Only) Side Handrail End Handrails 2 No. MT N Scale Body Mount Coupler Shorten
More informationTip: and Orient Express LED Light Upgrade Date: Correction
Hi All, I have since inherited my friend Rudolf s 42755 Orient Express with the extra 42760 car set and wanted to complete the LED light upgrade as we had planned. Side view of the Restaurant car with
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationZ8 Engine Start Button Install for the BMW E46 3 Series
Z8 Engine Start Button Install for the BMW E46 3 Series This write up is a specific installation of a Z8 engine start button on the E46, but it can be used as a general guide for an engine start button
More informationBehringerMods.com. Instructions for modification of Behringer DCX analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer DCX analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationMicro-Tsunami Digital Sound Decoder Quick Start Guide
Micro-Tsunami Digital Sound Decoder Quick Start Guide for the Experienced User Software Release 1.04 Notice The information in this document is subject to change without notice. SoundTraxx (Throttle Up!)
More informationFord 7.3L Powerstroke Positive Air Shutoff
24 October 2012 Ford 7.3L 1999.5-2003 Positive Air Shutoff 1 1999.5-2003 Ford 7.3L Powerstroke Positive Air Shutoff P/N# 1036700 P/N# 1036700-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION 24 October
More information2005+ Mustang Trunk Lid Release and Trunk Lights Installation
There is no warranty expressed or implied by this document, you follow these instructions at your own risk. These instructions worked for me, but your experience may vary. The final product of these instructions
More informationOracle Halo Headlight Conversion Kit - White (10-12 All)
Oracle Halo Headlight Conversion Kit - White (10-12 All) Tools needed: Small flathead screwdriver Large flathead screwdriver Ratchet 7 mm, 8mm, and 10mm socket Oven Heat Gun 2 2x4 12 long (other will work,
More informationNorfolk & Western Y6a Mallet
2003 Kohs & Company, Inc - Clarkston, Michigan 48348 Norfolk & Western Y6a Mallet OPERATION AND MAINTENANCE INSTRUCTIONS The Kohs & Company Norfolk & Western Y6a locomotive is an exact scale replica of
More informationNorfolk & Western Y6b Mallet
2002 Kohs & Company, Inc - Clarkston, Michigan 48348 Norfolk & Western Y6b Mallet OPERATION AND MAINTENANCE INSTRUCTIONS The Kohs & Company Norfolk & Western Y6b locomotive is an exact scale replica of
More informationMONGOOSE. Introduction. < blueroomelectronics > Assembly Instructions. Mongoose was designed as an introduction to Mechatronics.
MONGOOSE Assembly Instructions Introduction Mongoose was designed as an introduction to Mechatronics Page 1 of 12 Before you start The Mongoose is a complex kit and skipping instructions is not advised,
More informationInstallation Instructions - D-Series Warming Cabinet Instruction Door for Hinge UseReversal (Glass and Stainless Steel Doors)
Header Cam Lock Reversal... pg 1-4 Glass Door hinge reversal..... pg 5-9 Steel Door hinge reversal..... pg 10-13 Remove Panels Before reversing door hinges, the Header Cam Lock assembly must be reversed.
More informationGM 6.6L (LLY, LZB, LMM) Duramax Positive Air Shutoff 2.5 CAC TUBES
8 April 2013 1036712 GM/Chevy Duramax 2004.5-2010 (LLY,LBZ,LMM) Positive Air Shutoff 1 2005-2010 GM 6.6L (LLY, LZB, LMM) Duramax Positive Air Shutoff 2.5 CAC TUBES P/N# 1036712 P/N# 1036712-M UPLEASE READ
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationTip: - Württemberg Era 1 Open Platform Cars LED Lighting Upgrade Date: , Photos
Hi All, As I continue my LED light conversions of my rolling stock I have just completed all the Württemberg era 1 open platform cars I have which will make up four trains with eight cars per train. These
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL AND IGNITION 2008-2013 Arctic Cat Thundercat 1000 / XT Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips
More informationPower Seat Side Mount Installation & Wiring Instructions
F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Power Seat Side Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping and/or soldering. That
More informationFord 6.7L Powerstroke Positive Air Shutoff
8 April 2013 Ford 6.7L 2011-2012 Positive Air Shutoff 1 2011-2012 Ford 6.7L Powerstroke Positive Air Shutoff P/N# 1036703 P/N# 1036703-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD Engine Brake
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationStep #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good t
How to make a ROV! Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good to have extras. Using the wire cutter,
More informationThe speaker soundbox improves the performance of the speaker in locos which have no purpose designed speaker cradle.
1 1.OVERVIEW 8 pin DCC sound decoder with adjustable back-emf loco control. Fully adjustable sounds to match the chuff and whistle to the prototype loco. Provides a chuff which matches the loco speed and
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display 2004 onwards Ford F-150 and 2008 onwards Ford Super Duty (Kit part numbers 1008-9520 and 1008-9525) Kit Contents: RVS Interior (shorter) Harness RVS Chassis (longer) Harness
More informationBachmann D11 EM/S4 Finescale Conversion
Bachmann D11 EM/S4 Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationInstallation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output)
Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output) PN L300080607 Revision - 1.1 Lingenfelter Performance Engineering
More informationGM 6.6L (LML) Duramax Positive Air Shutoff 2.5 CAC TUBES
8 April 2013 1036713 GM/Chevy Duramax 2011-2013 (LML) Positive Air Shutoff 1 2011-2013 GM 6.6L (LML) Duramax Positive Air Shutoff 2.5 CAC TUBES P/N# 1036713 P/N# 1036713-M UPLEASE READ ALL INSTRUCTIONS
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationDesire Streetcar Installation Guide
Desire Streetcar Installation Guide 2004 Phoenix Sound Systems, Inc. All Rights Reserved. Page 1 1 Mar 04 Overview The LGB Streetcar is one of the more interesting (e.g. difficult, challenging) installations.
More informationWOC & WOC Top & Back Installation Instructions
Shown with optional Sun Roof WOC-900500-2 & WOC-900501-2 Top & Back Installation Instructions Install Order! Heater Door System Wiper on to Windshield Windshield Rear Panel Top Panel Tools needed: 5/16
More information* * Inside Toyota Avalon. Tools Required IMPORTANT
Revision 08/02/16 2013- Toyota Avalon IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationBanks SmartLock. THIS MANUAL IS FOR USE WITH system 55270
owner s manual with installation instructions Banks SmartLock 2003-Early 2004 Dodge 5.9L CUMMINS TURBO DIESEL TRUCKS THIS MANUAL IS FOR USE WITH system 55270 Gale Banks Engineering 546 Duggan Avenue Azusa,
More informationTip: 2856 LED Lighting for the Airport Express Set Date:
Hi All, The 2856 Airport Express set was manufactured in 1983. On 09-11-1989 the locomotive was given a digital upgrade using a 6080 decoder. It has since had a digital upgrade to a high performance motor
More informationBottom Mount Seat Mount Installation & Wiring Instructions
E81/E87/E90/E91/E92/F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Bottom Mount Seat Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping
More informationKodak 750H Carousel Projector Repair
Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL and IGNITION 2016 Yamaha Wolverine Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationRear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number )
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationSide Mount Installation & Wiring Instructions
E81/E87/E90/E91/E92/F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Side Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping and/or soldering.
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL AND IGNITION 2017 Kawasaki Z125 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab 1 Posi-tap
More informationBachmann GWR Earl (Dukedog) EM Finescale Conversion
Bachmann GWR Earl (Dukedog) EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationBLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES
BLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES 2012 AkitikA, LLC All rights reserved Revision 1p3 April 18, 2012 Page 1 of 15 Table of Contents Table of Contents... 2 Table of Figures... 2 Section
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More informationlkm7001 key override module Installation Instructions Converting The LKM7000 to The LKM7003
lkm7001 Instructions Converting The LKM7000 to The LKM7003 key override module In A Single Motion, We ll Change The Way You Think About Security Read Instructions thoroughly prior to installation Base
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More information