Installing a TCS FL4 into the Eureka CTH Ben O Malley
|
|
- Mavis Bryant
- 5 years ago
- Views:
Transcription
1 Please note, this modification requires soldering skill at board level and involves removing surface mount components. This modification will also void your warranty and all responsibility resides with the person making the modification. As the CTH comes fitted with a basic Bachmann decoder, the lighting functions are rather limited. This decoder only has two functions which means that the internal lights are always on and you either have red marker lights when the CTH is trailing or both the headlight and marker lights on when the CTH is leading. This install will allow full control of all four light circuits, namely the internal lights, the headlight and both red and white marker lights. CTH as supplied, while on powered track the internal lights are always on
2 The first step is to remove the body. The body is only secured by clips and is easy to remove by inserting something slim between the body sides and the under frame on both sides and the body should pop off. Removing the body CTH with body removed
3 With the body removed, you can then unplug the supplied Bachmann decoder. Body removed showing the top of the circuit board Remove the four black plastic clips that hold the power pickup wires from the bogies. These are labeled as VCC+ and VCC-. You can either set these aside to be reused later but the recommendation is to throw these and solder the wires. Next you need to unsolder the two wires that go to the switch in the under frame that enables or disables the headlights and marker lights. This is labeled as S3. Also unsolder the wires from the switch as this is no longer required. Once all wires have been disconnected, you can remove the three small black screws that hold the circuit board. It is easier and safer to fully remove the board but it can be left in if you are confident in doing so. Remove all five diodes, these are marked D4 through D8 and have the code M2 on them.
4 The TCS FL4 is a small 4 function, function only decoder. This means it can control up to 4 separate outputs that can be used for lighting or other low power devices but has no motor control which is perfect for this application. The reduced size also means it now fits in the roof cavity of the CTH above the circuit board, unlike the Bachmann decoder which sits in the luggage/guards compartment. Showing the size difference of the TCS FL4 (left) and the supplied Bachman decoder (right)
5 CTH circuit board with TCS FL4 wired in (ignore long blue wire) To install the FL4, you need to install a link bridging S3 where we removed the switch wires. Now solder the following wires to the following locations. RED (right rail) to the solder pad at the pointy side of D8 BLACK (left rail) to the solder pad at the pointy side of D7 BLUE (decoder common / V+) to the either solder pad between D4 and D5 GREEN (headlight) to a machine pin socket to form a socket VIOLET (white marker lights) to the solder pad at the non pointy end of D5 BROWN (red marker lights) to the solder pad at the non pointy end of D6 PINK (internal lights) to the solder pad at the non pointy end of D7 BLACK with WHITE stripe (decoder ground) leave unconnected. You can cut each wire to length for a cleaner install or leave the wires at their full length and just tape them in place. Screw the circuit board back onto the under frame and solder the four wires from the bogies back onto the VCC+ and VCC- locations. A further enhancement can be made by soldering the other end of these wires to the bogies directly, removing the reliance on those plastic caps. If you do this, you will have to file the blackening coat of the bogie tabs to allow the solder to tin them.
6 Close up of connection points FL4 and wires taped into place
7 Next is to modify the wiring in the body of the CTH. This involves removing the two screws that hold the circuit board in place and gently lifting the board loose and then unsoldering the magnet wire from the WHITE solder point next to the COM point. This wire is the negative wire to the LED headlight. On to the end of this wire solder a 1K resistor and a machine pin socket to form a plug and cover with heat shrink tubing. Reinstall the board with the wire poking out the back. modified body wiring for the headlight
8 Plug the headlight pin into the GREEN wire socket and clip the body back onto the under frame and place onto the track for programming. Ready to be put back together How you program your CTH is up to you so I will describe how I have set mine up as a guide only. Program the decoder address to match the address used in the CPH. this removes the need to run the CPH and CTH in consist mode. Function control; F0f not used. F0r Headlight on in reverse, this means the CTH is leading. F1 Headlight dim (known as Rule 17 in the US) This means on NCE ProCab and PowerCab systems, the BELL button is used to dim the headlights. In Australia, we have very few locomotives that have a bell remapping this function is fine. F3 Internal lights (this also means you have to remap functions on the CPH as the default is F11) F4 Marker lights, set up to be directional (also remapping in the CPH to disable the output)
9 When configuring the FL4, things to be aware of, is the instruction manual that is supplied has incorrect control CV s listed. Using JMRI/Decoder Pro to configure the FL4 does make the basic configuration easier but at this stage, the decoder profile doesn t list all the option. The main issue that is common to both the instructions and the JMRI profile is setting up Rule 17 and which function it responds to. JMRI/Decoder Pro screen for setting up the function mapping
10 JMRI/Decoder Pro screen for setting up lighting control After configuring the FL4 in JMRI/Decoder Pro you must then manually change CV 123 to set what function the dimmer (Rule 17) operates on. The value of 4 sets it to F1.
Application Note. Walthers/Proto 2000 E7A Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-1000 digital sound decoder into a Walthers/ Proto 2000 E7A. Skill Level 2: The entire installation can be completed in one
More informationAtlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes
Atlas HO MP-15 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an Atlas HO MP-15. Skill Level 2: The entire
More informationApplication Note. Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes
Application Note Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into a Bachmann HO F40PH. Skill
More informationCabin Light. Hi All, 1
Hi All, My friend Rudolf set me a challenge for his 36331 electric locomotive, wanting Telex couplers fitted. When I opened up the locomotive I discovered there is very little room to add extra components
More informationBachmann Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann 2-6-6-2 Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital
More informationTip: 3652 and 3756 Crocodiles with LP4.0 and LED Lighting Date:
Hi All, My friend Adrian asked me to convert two crocodiles 3652 and 3756 using LokPilot 4.0 decoders. Adrian wanted to run both locomotives as a double headed configuration so this would require that
More informationAthearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40T-2. Skill Level 2: The entire
More informationTip: 3425 Kittle Loco with LP4.0 Micro Conversion and LED Lighting Date: , Corrections Addition Link added
Hi All, This is the last of Rudolf s LokPilot Micro V4.0 decoder conversions. He asked me to convert his Märklin Delta 3425 steam locomotive and wanted to improve the lighting effects for the cabin, change
More informationAthearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD CF7. Skill Level 2: The entire
More informationMustang One-Touch Convertible Top Module (2005+) - Installation Instructions
Mustang One-Touch Convertible Top Module (2005+) - Installation Instructions The below installation instructions work for the following products: Mustang One-Touch Convertible Top Module (2005+) Please
More informationGOMINIGO Third Brake Light Pulsar Kit. Installation Instructions
Page 1 of 8 Mini Cooper Installation Instructions This kit allows the owner of any MINI Cooper or Cooper S to create a blinking effect from the third brake light assembly. The MINI Cooper being hit from
More informationSound Install Steam. Presented by Tim s Trains
Presented by Tim s Trains This presentation will show you the basic steps required to install a sound decoder and speaker in a steam locomotive. This particular locomotive is a Bachmann 4-8-4 with a Vanderbilt
More informationAthearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD GP35. Skill Level 2: The
More informationAthearn Genesis GP38-2 Tsunami Digital Sound Decoder Installation Notes
Athearn Genesis GP38-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 digital sound decoder into an Athearn Genesis HO GP38-2. Skill
More informationAthearn SD40 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40. Skill Level 2: The entire installation
More informationThe Mysteries of DCC Consisting. Presented by Tims Trains and Hobbies
The Mysteries of DCC Consisting Presented by Tims Trains and Hobbies What is CONSISTING?? Consisting or MU ing is the process of running two, or more, locomotives as one unit, on any given throttle, on
More informationHi All, Update
Hi All, With the success of my last Telex conversion on the 3704 locomotive I chose the 3796 tank locomotive to add Telex couplers controlled by a LokPilot 4 decoder. The locomotive does an un-coupling
More informationAtlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes
Atlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an Atlas Silver
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationApplication Note. Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an HO Atlas RS-3. Skill Level
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24075 2003 ACCORD P/N 08V31-SDN-100 2-DOOR Issue Date AUG 2002 NOTE: The outside temperature gauge can not be installed in a vehicle
More informationThis year Märklin have released a coach which has included LED lighting with a currentconducting close coupler (single pole)
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationTip: 2856 LED Lighting for the Airport Express Set Date:
Hi All, The 2856 Airport Express set was manufactured in 1983. On 09-11-1989 the locomotive was given a digital upgrade using a 6080 decoder. It has since had a digital upgrade to a high performance motor
More informationNCE DCC TWIN. In addition to the NCE DCC TWIN, you will need:
NCE DCC TWIN Welcome to the world of DCC! This manual will familiarize you with the set up and operation of two locomotives on your railroad using the NCE DCC TWIN. In addition to the NCE DCC TWIN, you
More informationBachmann Spectrum Peter Witt in HO
Bachmann Spectrum Peter Witt in HO By Bob Dietrich This is my impression of an unpainted Peter Witt from Bachmann Spectrum. The packaging of the car was impressive a large red box with a clear cover showing
More informationCLASSIC UPDATE WIRING KIT
by Randy Irwin 1955-57 CLASSIC UPDATE WIRING KIT Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 25 years. He is a wizard at creating, making and modifying custom
More informationBroadway Limited (and Blueline) SD40-2 Tsunami Digital Sound Decoder Installation Notes
Broadway Limited (and Blueline) SD40-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into a HO Broadway Limited
More informationApplication Note. Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes
Application Note Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 digital sound decoder into an Athearn Genesis
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDN-100 2004 ACCORD 2-DOOR AII 25735 Issue Date SEP 2003 NOTE: The outside temperature gauge can not be installed in a vehicle
More informationDH165IP Fits Many HO Locomotives with DCC 8pin Medium Socket
Digitrax Command Control Run Your Trains, Not Your Track! DH165IP Fits Many HO Locomotives with DCC 8pin Medium Socket HO Scale Mobile Decoder DCC Plug N Play 1.0 Amp/1.5 Amp Peak 6 FX 3 Functions, 0.5
More information5 Amp Dual Mode Sound Decoder by Frank T.Verrico
5 Amp Dual Mode Sound Decoder by Frank T.Verrico Model Rectifier Corp. s latest venture into O scale is a 5 amp. dual mode, [DC/DCC], sound decoder. This full featured N.M.R.A. compatible sound decoder
More informationAthearn RTR F59PHI Tsunami Digital Sound Decoder Installation Notes
Athearn RTR F59PHI Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 Digital Sound Decoder into an Athearn HO Ready to Roll EMD F59PHI
More informationWalthers/Life-Like USRA Steam Locomotive
North Raleigh Model Railroad Club Installing Decoders in N Scale Locomotives Detailed Instructions Walthers/Life-Like USRA 2-8-8-2 Steam Locomotive by David Derway May 17, 2010 Table of Contents Introduction...
More informationATLAS HARNESS. Plug and play wiring harness $12.95
ATLAS HARNESS Plug and play wiring harness $12.95 Converts D408SR decoder to a plug and play decoder for: Weaver 2-8-0 and New Haven I-5 Atlas (new)sw8/9, RS1, C44-9, SD35, C40-8, and other locomotives
More informationLenz Gold Maxi DCC Decoder Install for DCC operation with Sound for Bachmann s K27 Large Scale Steam Locomotive
Lenz Gold Maxi DCC Decoder Install for DCC operation with Sound for Bachmann s K27 Large Scale Steam Locomotive Lenz produces a DCC decoder that easily installs in the Bachmann K-27. The following installation
More informationDavis Pro2 Sensor Interface Module (SIM) Supercap Replacement
1 507 NW 60th Street Suite D Gainesville, FL, 32607 USA Phone: (352) 262-6119 Email: ryanwilhour@gmail.com Davis Pro2 Sensor Interface Module (SIM) Supercap Replacement Table of Contents Introduction...
More informationTip: LED Lighting for the 4367 SBB Euro City Set, 4366 and 4368 Cars Date: , Corrections Modified , Photos
Hi All, I have had the 4367 SBB Euro City set with extra cars 4366 and 4368 since 1998, apart from a test run on the layout they have stayed in storage ever since. I decided to change some rolling stock
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA-102 2007 ACCORD 4-DOOR AII 32672 Issue Date JULY 2006 NOTE: Fog lights can be installed in a vehicle equipped with a factory
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA-102 2007 ACCORD HYBRID AII 32762 Issue Date JULY 2006 NOTE: The outside temperature gauge cannot be installed in a vehicle
More informationTip: - Württemberg Era 1 Open Platform Cars LED Lighting Upgrade Date: , Photos
Hi All, As I continue my LED light conversions of my rolling stock I have just completed all the Württemberg era 1 open platform cars I have which will make up four trains with eight cars per train. These
More informationApplication Note. KATO SD40-2 Mid Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a Tsunami TSU-KT1000 Digital Sound Decoder into the HO Kato SD40-2 (Mid-production). Skill Level 2: The entire installation can
More informationKato P42 Tsunami Digital Sound Decoder Installation Notes
Kato P42 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes the procedure for installing a TSU-KT1000 Digital Sound Decoder into a Kato HO P42 locomotive. Skill Level
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2010 INSIGHT Publications No. AII 40881 Issue Date MARCH 2009 PARTS LIST Right fog light bracket D Fog Lights Kit P/N 08V31-TM8-100 Left fog light Fog
More informationTip: Difficult Conversions for F800 (3026) and 3111 Date: Led lighting added, LED Addition 3111
Hi All, It s good to revisit previous conversions and see if you can improve on what has been done before. I decided to add LED lighting to my F800 (3026) and 3111. This document update shows how it was
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SECURITY SYSTEM P/N 08E49-SDA-100 ACCORD 2- AND 4-DOOR AII 30666 Issue Date AUG 2005 PARTS LIST Hood switch harness Illustration of the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD AII 24050 4-DOOR P/N 08V31-SDA-100 Issue Date AUG 2002 NOTE: The outside temperature gauge cannot be installed in a vehicle with
More informationUSER MANUAL FOR ATLAS HO DUAL-MODE 4-FUNCTION DCC DECODER (ITEM #342)
HO Dual-Mode 4-Function Decoder 1 USER MANUAL FOR ATLAS HO DUAL-MODE 4-FUNCTION DCC DECODER (ITEM #342) By Dual Mode, we mean that the Atlas #342 HO 4-function decoder has a jumper plug that allows the
More informationTip: and Orient Express LED Light Upgrade Date: Correction
Hi All, I have since inherited my friend Rudolf s 42755 Orient Express with the extra 42760 car set and wanted to complete the LED light upgrade as we had planned. Side view of the Restaurant car with
More informationTesla Model S Rear Lighted T
Tesla Model S Rear Lighted T Installation Instructions The rear lighted T makes your Tesla Model S distinctive if not unique from other cars on the road and other Model S s. This LED powered device is
More informationBOM505 Black Out Module Ford F-150 Contact InterMotive for additional applications
An ISO 9001:2008 Registered Company BOM505 Black Out Module 2015-2016 Ford F-150 Contact InterMotive for additional applications Introduction The BOM505 module has the ability to eliminate all exterior
More informationDH163PS Fits Many DCC-Ready HO Locomotives
Digitrax Command Control Run Your Trains, Not Your Track! DH163PS Fits Many DCC-Ready HO Locomotives HO Scale Mobile Decoder DCC Plug N Play with 1.25 Harness 1.5 Amp/2 Amp Peak 6 FX3 Functions, 0.5 Amp
More informationAthearn Pacific Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Overview This application note describes how to install a DSD-100LC Digital Sound Decoder into the Athearn Pacific Locomotive. All of the
More informationGIVE ME A BRAKE Light Kit 2005 / 2006 MINI Cooper/Cooper S Brake Light Modification
Page 1 of 6 GIVE ME A BRAKE Light Kit 2005 / 2006 MINI Cooper/Cooper S Brake Light Modification ****Pages 1 and 2 apply only to non-convertible MINI s**** ****for convertibles please go to page 5**** This
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2004 CR-V AII 26118 Issue Date SEP 2003 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9A-100
More informationBy Mark Schutzer PCR Regional Convention, San Luis Obispo May 2014 Copies of this presentation can be found at
A Beginners Guide to Installing DCC Decoders By Mark Schutzer PCR Regional Convention, San Luis Obispo May 2014 Copies of this presentation can be found at http://www.markschutzer.com Clinic Overview Installing
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-100B 2008 ELEMENT (SC) AII 36532 Issue Date MAY 2007 PARTS LIST Relay bracket Right fog light Relay Left fog light Fuse
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176-28932 2005 CR-V Issue Date S P/N 08V31-S9A-115 FEB 2005 PARTS LIST 6 Washer-bolts Left fog light 6 Spring nuts Harness bracket
More informationHow to: Install the HomeLink equipped Sun Visor into a 2005 Subaru Legacy (2.5i or 2.5GT) Revised 03/17/2005
How to: Install the HomeLink equipped Sun Visor into a 2005 Subaru Legacy (2.5i or 2.5GT) Revised 03/17/2005 The following should be performed at your own risk; I've created these instructions as a courtesy
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationInstallation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14
Installation Tips Crimestopper/ProStart Remote Start system + PLJX + DLRM + SPDT (for GM vehicles) T0760 v1.1 updated 2/5/14 Thank you for purchasing your remote start from MyPushcart.com - an industry
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26014 ODYSSEY Issue Date AUG 2003 PARTS LIST Hood Switch (sold separately) P/N 08E49-S0X-100G Illustration of the Hood Switch Installed
More informationIdle Timer Controller - A-ITC520-A Ford E Series Ford F250 - F Ford F250 - F550 (*B-ITC520-A) F650/F750
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC520-A 2009-2018 Ford E Series 2008-2016 Ford F250 - F550 2017-2018 Ford F250 - F550 (*B-ITC520-A) 2016-2018 F650/F750 *Uses the Ford 24-Pin
More informationThe speaker soundbox improves the performance of the speaker in locos which have no purpose designed speaker cradle.
1 1.OVERVIEW 8 pin DCC sound decoder with adjustable back-emf loco control. Fully adjustable sounds to match the chuff and whistle to the prototype loco. Provides a chuff which matches the loco speed and
More informationIn this installment we will look at a number of things that you can do with LEDs on your layout. These will include:
Introduction The first article in this series, LEDs 101 - The Basics, served to review the characteristics and use of LED lighting in a garden railway environment. It also generated a host of questions
More informationIdle Timer Controller - ITC515-A Ford Transit Contact InterMotive for additional vehicle applications
An ISO 9001:2008 Registered Company Idle Timer Controller - ITC515-A 2015-2018 Ford Transit Contact InterMotive for additional vehicle applications Overview The ITC515-A system will shut off gas or diesel
More informationTIP SHEET T0491. Installation Tips for your Excalibur RS Passlock-sl2(4) + DLRC + SPDT
TIP SHEET T0491 Installation Tips for your Excalibur RS-360 + Passlock-sl2(4) + DLRC + SPDT For Chevrolet: Astro 1998-2005, Avalanche 2002, Blazer 1998-2005, Cavalier 2000-2003, Express Van 1998-2005,
More informationLocomotive decoder LE1025 1
Locomotive decoder LE1025 1 The DIGITAL plus locomotive decoder LE1025 is suitable for all DC motors in HO scale locomotives with continuous current draw of 1.0 Amp. or less. The characteristics of the
More informationPRELIMINARY INSTALLATION INSTRUCTIONS PARTS LIST. Combination light switch Right fog light. 4 Self-tapping washer-screws.
INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SCV-100D Application 2009 ELEMENT (SC) Publications No. AII 40515 Issue Date OCT 2008 PARTS LIST Combination light switch Right fog light Left fog light
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B. Display bracket.
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2006 PILOT All 30502 Issue Date SEP 2005 PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B Display
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label
More informationSP Switch Programmable Switch Panel Power System. Parts Included
SP8100 8-Switch Programmable Switch Panel Power System Parts Included 1 Switch Panel 1 100 amp Power Module 1 Power Module Harness 1 Power Module Mounting Plate 1 Battery Cable w/100a MIDI fuse (Littlefuse
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (DX, HX, VP) 2005 CIVIC 2- AND 4- DOOR AII 27865-30866 Issue Date SEP 2005 NOTE: Fog Lights cannot be installed if the vehicle is equipped
More informationRFB MK6 Jetta Fog Light Kit Wiles Rd.Coral Springs, FL
What s Included: Tools Required: (2) Fog Lights (2) Front Grills Wire Harness Headlight Switch Hardware Kit T25 Torx Wire Cutters 10mm Socket and Rachet Headlight Switch Composite Wedge Tool 01 1. Remove
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TP6-100 Application 2010 ACCORD CROSSTOUR Publications No. AII 41935 Issue Date NOV 2009 PARTS LIST TOOLS AND SUPPLIES REQUIRED Ambient Light Kit Ambient
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176 2005 CR-V Issue Date P/N 08V31-S9A-114 SEP 2004 PARTS LIST 25 Wire ties Left fog light 6 Washer-bolts Right fog light 6 Spring
More informationBachmann. Climax. Phoenix Sound Systems, Inc West Liberty Road Ann Arbor MI
Bachmann Climax Phoenix Sound Systems, Inc. 3514 West Liberty Road Ann Arbor MI 48103 www.phoenixsound.com phone: 800-651-2444 fax: 734-662-0809 e-mail: phoenixsound@phoenixsound.com 2004-2007 Phoenix
More informationSCA-80(Q) C11 REPLACEMENT ASSEMBLY MANUAL
SCA-80(Q) C11 REPLACEMENT ASSEMBLY MANUAL 2014-2016 AkitikA, LLC All rights reserved Revision 1p05 July 3, 2016 Page 1 of 15 Table of Contents Table of Contents... 2 Table of Figures... 2 Section 1: About
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30528 INTERFACE 2006 CR-V Issue Date SEP 2005 PARTS LIST XM Radio Unit Kit (sold separately): P/N 08A15-EX5-000 2 Wire tie with clips
More informationBOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications
An ISO 9001:2008 Registered Company BOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications Introduction The BOM507-BC module has the ability to eliminate all exterior
More informationInstallation Tips For Crimestopper RS7 + Passlock-sl2(4) + DLRM + SPDT
TIP SHEET T3628 Installation Tips For Crimestopper RS7 + Passlock-sl2(4) + DLRM + SPDT For Chevrolet: Astro 1998-2005, Avalanche 2002, Blazer 1998-2005, Cavalier 2000-2003, Express Van 1998-2005, S10 Pickup
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 26124 CR-V Issue Date SEP 2003 P/N 08V31-S9A-112 PARTS LIST 4 Washer-bolts, 6 x 20 mm Left fog light 2 Small spring nuts Right fog light
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-102 2008 ELEMENT AII 36531 Issue Date MAY 2007 PARTS LIST 15 Wire ties 2 Fog lights 4 Wire ties with clip Switch harness
More informationDash Procedure (Dash Cluster Corvette) for color upgrade
Dash Procedure (Dash Cluster 1984-1989 Corvette) for color upgrade Chapter 1 Please read all instructions before proceeding. 1. Disconnect negative battery cable. 2. Use small flat blade screw driver to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-110A Application 2012 ACCORD 2- AND 4-DOOR Publications No. AII 46501 Issue Date AUG 2011 PARTS LIST Ambient Light Kit Fuse label 2 Ambient lights Washer
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33026 S 2007 ODYSSEY Issue Date JULY 2006 PARTS LIST Short sub harness (LX model) Right fog light Long sub harness (EX model and Touring
More informationWIRING THE HEATER POWER SUPPLY
WIRING THE HEATER POWER SUPPLY Fig. 14 13/14 Take the longer PS board (with the 47R resistors and the fuse) and, using M3x6 screws, fix it to the chassis to the left of the mains transformer. The diodes
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display 2004 onwards Ford F-150 and 2008 onwards Ford Super Duty (Kit part numbers 1008-9520 and 1008-9525) Kit Contents: RVS Interior (shorter) Harness RVS Chassis (longer) Harness
More informationXX, TOYOTA, TACOMA FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY
FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY Know safety, no injury. Know injury, no safety. ~Author Unknown If there are any questions, call 1-855-HHTOUGH
More informationREC-11+ REMOTE RECEIVER UNIT
Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous
More informationINSTALLATION INSTRUCTIONS
Rear Vision System NAV Display 2009-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9501) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness NAV Harness 1
More informationInstallation Manual Volvo C30 T5 Front Mount Intercooler System
Installation Manual Volvo C30 T5 Front Mount System Volvo C30 T5 System / Installation Manual i C Contents Important Information i Parts List i Required Tools and Materials 1 1.0 - Vehicle Preparation
More informationIdle Timer Controller - A-ITC620-A Chevrolet Express/GMC Savana
An ISO 9001:2008 Registered Company Idle Timer Controller - A-ITC620-A1 2009-2018 Chevrolet Express/GMC Savana Contact InterMotive for additional vehicle applications Introduction The A-ITC620-A1 is an
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC All 30175-31616 2 AND 4-DOOR P/N 08E10-SNA-100 Issue Date DEC 2005 NOTE: The interior illumination lights cannot be installed on 2-door
More information