INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Dale Phelps
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII ACCORD P/N 08V31-SDN DOOR Issue Date AUG 2002 NOTE: The outside temperature gauge can not be installed in a vehicle with fog lights. Fog light harness PARTS LIST Right fog light Switch harness Left fog light Switch Right bracket A Relay (black) Left bracket A Relay (gray) Right bracket B Fuse label Left bracket B 4 Self-tapping screws Right trim 4 Step-screws Left trim 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 08V31-SDN of 19

2 2 Ground bolts Washer, 6 mm 4 Washers, 5 mm (gold) 4 Washers, 4 mm TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver 8 mm and 10 mm Combination wrench 10 mm Socket Ratchet File Diagonal cutters Masking tape Utility knife 3 Washer-bolts, 6 x 16 mm Illustration of the Fog Lights Installed on the Car 4 Washer-bolts, 5 x 12 mm 4 Washer-screws, 4 x 12 mm (black with big washer) FOG LIGHT 4 Washer-screws, 4 x 10 mm (black with small washer) 2 Washer-screws, 4 x 8 mm (gold) 25 Wire ties RIGHT FOG LIGHT LEFT (2) Relay bracket 4 Spring nuts Fuse (20A) 2 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

3 INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. Routing the Fog Light Harness 3. Open the hood. Remove the radiator cover (ten clips and four retaining tabs). 5. Remove the air duct cover (two clips and pull it out toward you). Remove the air duct by pulling it out toward you. L4 Model: CLIPS (2) AIR DUCT CLIPS (10) AIR DUCT V6 Model: RADIATOR CLIP AIR DUCT RETAINING TAB 4. Remove the hood latch cover (one clip). CLIP HOOD LATCH AIR DUCT 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 3 of 19

4 6. Route the fog light harness 2-pin connector through the front bulkhead and alongside the vehicle harness. 2-PIN 9. On the left side of the vehicle, secure the fog light harness to the vehicle harness with the five wire ties in the areas shown. Push the fog light harness clip into the hole in the body panel. HOLE 7. Route the 2-pin connector end of the fog light harness to the front bulkhead alongside the vehicle harness. GROUND TERMINAL 6 mm WASHER HOOD LATCH BRACKET GROUND BOLT 10. On the right side of the vehicle, secure the fog light harness to the vehicle harness with four wire ties. WIRE TIE CLIP WIRE TIE BOLT (Discard) GREEN TAPE 8. Remove and discard the lower bolt that secure the hood latch bracket. Using one ground bolt and the 6 mm washer supplied, attach the fog light harness ground terminal to the hood latch bracket. ( Do not allow the harness to contact the air conditioner pipe.) AIR CONDITIONER PIPE 4 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

5 11. Remove the two bolts that fasten the relay box. BOX BOLT 14. Lift the air cleaner housing cover up, and route the other end of the fog light harness toward the engine alongside the vehicle harness. BOLT Lift AIR CLEANER HOUSING BOLT (Remove.) AIR CLEANER HOUSING 12. Remove the one bolt that fastens the air cleaner housing cover. 13. Release the six retaining tabs and remove the relay box under cover. BOX RETAINING TABS (6) BOX UNDER 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 5 of 19

6 15. Unplug the vehicle 14-pin and 20-pin connectors from the relay box. Release the lock on the vehicle 14-pin connector, and push the fog light harness white/green and red/green wire terminals into the vehicle 14-pin connector. Reattach the lock on the 14-pin connector. 18. Secure the fog light harness to the vehicle harness with one wire tie in the area shown. BOX BOX UNDER 14-PIN BOX 20-PIN As viewed from back side 14-PIN LOCK BOX RED/GREEN TERMINAL Harness WHITE/ side GREEN view TERMINAL BLUE/RED TERMINAL LOCK Harness side view 20-PIN 19. Reinstall the relay box under cover. Be careful not to pinch the wires. 20. Under the relay box, locate the vehicle 3-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Connect the fog light harness 3-pin connector into the 3-pin connector you just freed. Secure the fog light harness to the vehicle harness with one wire tie in the area shown. A/T Model: BOX BLUE- TAPE (Remove.) 3-PIN 14-PIN 20-PIN TERMINALS (3) WIRE TIE 16. Release the lock on the vehicle 20-pin connector, and push the fog light harness blue/red wire terminal into the vehicle 20-pin connector. Reattach the lock on the 20-pin connector. 17. Plug the vehicle 14-pin and 20-pin connectors back into the relay box. 3-PIN 6 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

7 M/T Model: 21. Install the relays (black and gray) to the relay bracket with two 6 x 12 mm washer-bolts. 3-PIN BOX BLUE- TAPE (Remove.) 6 x 12 mm WASHER- BOLT BRACKET (Fold back) 3-PIN NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to that other accessory's harness. Remove the tape and dummy connector from that other accessory's harness. Plug the fog light harness 3-pin connector into that other accessory's harness. 22. Plug the fog light harness two 4-pin connectors into the relays. L4 Model: BRACKET (If equipped.) (Black) MOUNTING BOLT (Reuse.) (Gray) OTHER ACCESSORY 3-PIN 3-PIN 3-PIN BRACKET (Black) WIRE TIE 4-PIN (Brown) (Gray) 4-PIN (Blue) OTHER ACCESSORY 3-PIN 23. If equipped, remove the mounting bolt that secures the vehicle bracket, and attach the relay bracket with this bolt American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 7 of 19

8 On the V6 model, attach the relay bracket to the vehicle frame with the 6 x 12 mm washer-bolt supplied. 25. Secure the fog light harness to the vehicle harness with three wire ties in the areas shown. V6 Model: 6 x 12 mm WASHER-BOLT FRAME BRACKET (Black) 4-PIN (Brown) (Gray) 4-PIN (Blue) 24. If the fog light harness is routed near a vehicle 4- pin harness connector, secure the fog light harness to the vehicle harness with one wire tie. 26. Remove the relay box cover (four retaining tabs), and install the 20A fuse (provided) into the No.10 slot of the relay box. BOX RETAINING TABS (4) FUSE (20A) FUSE (20A) BOX ( No. 10 Slot) BOX 8 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

9 27. Attach the 20A fuse label over the No.10 slot of the relay box cover. Reinstall the relay box cover. 29. Remove the two self-tapping screws and remove the bumper duct and duct bracket. FUSE LABEL (20A) BUMPER DUCT No.10 Installing the Fog Lights BUMPER BOX LID If the vehicle you're working on is a V6 M/T model, continue with step 28, if not go to step Remove the front bumper (four bolts, six clips and two self-tapping screws). SELF- TAPPING SCREW MASKING TAPE CUT AREA DUCT BRACKET BUMPER OPENING 30. Attach the masking tape around the front bumper opening, and cut out the rib of the front bumper opening areas shown. Remove the burrs. BUMPER OPENING Do not cut the rib. CLIPS (6) BOLTS (4) SELF- TAPPING SCREWS (2) UTILITY KNIFE Do not cut the rib CUT AREA 31. Repeat steps 29 and 30 on the other side of the bumper. Reinstall the front bumper, then go to step American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 9 of 19

10 32. To prevent damage to the front bumper, apply masking tape to the front bumper on the left side of the vehicle in the area shown. 36. Slide the left bracket B onto the outside rib of the front bumper opening, then tighten the two 5 x 12 mm washer-bolts with the left bracket B pulled toward the front. CUT LINE INBOARD RIB ( Do not cut.) LEFT BRACKET B CUT LINE BUMPER OPENING BUMPER OPENING LEFT BRACKET B (Pull toward front.) RIB CUT AREA MASKING TAPE UTILITY KNIFE 5 x 12 mm WASHER- BOLTS (2) RIB 33. Being careful not to cut the inboard rib, use a utility knife to cut out the fog light opening. 34. Repeat steps 32 and 33 to cut out the right fog light opening. 37. Attach two spring nuts onto the ribs of the front bumper opening. LEFT BRACKET B 4 x 10 mm WASHER- SCREWS (2) ( Loosely install.) SPRING NUTS (2) 5 x 12 mm WASHER- BOLTS (2) (Loosen.) RIB RIB 35. Loosely install the two 5 x 12 mm washer-bolts and 4 x 10 mm washer-screws to the left bracket B. 10 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

11 38. With the left bracket A pulled out toward the front, attach it to the front bumper opening with two selftapping screws. 40. Install two 4 x 12 mm washer-screws and two 4 mm washers to the left trim. LEFT BRACKET A Inside view of bumper LEFT BRACKET A LEFT TRIM 4 X 12 mm WASHER- SCREWS (2) LEFT BRACKET A (Pull toward front.) SELF-TAPPING SCREWS 4 mm WASHERS (2) 41. Install the fog light harness clip into the hole in left bracket A. 39. Install the left fog light into the left trim with two step-screws and one 4 x 8 mm washer-screw. LEFT BRACKET A LEFT HOLE STEP- SCREW LEFT TRIM 4 x 8 mm WASHER- SCREW STEP- SCREW CLIP 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 11 of 19

12 42. Connect the fog light harness 2-pin connecter to the left fog light. Position the fog light on the front bumper, and tighten the two 4 x 12 mm washerscrews and two 4 x 10 mm washer-screws. 2-PIN LEFT FOG LIGHT 4 x 10 mm WASHER- SCREWS ( with big washer) 43. Repeat steps 35 thru 42 to install the right fog light. Routing the Switch Harness 44. Remove the driver s dashboard lower cover: Remove the one self-tapping screw. Release the four clips on the left side first by pulling out on the driver's dashboard lower cover. After releasing the four clips, insert the flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. Release the two clips on the right side last. Unplug the vehicle connector, and remove the lower cover. BUMPER 4 x 12 mm LEFT WASHER- FOG SCREWS LIGHT ( With small washer) CLIP (Release these clips first.) CLIP (Release these clips last.) CLIPS (7) SELF-TAPPING DRIVER'S SCREW DASHBOARD LOWER FRAME FLAT-TIP SCREWDRIVER CLIP (Release the clip by inserting the flat-tip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) 12 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

13 45. If equipped, remove the driver s dashboard under cover (three clips, one pin, and one holder). NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug its 6-pin connector from the fuse box. Locate the 6-pin connector taped to the switch harness. Remove the dummy connector from switch harness. Plug the other accessory's harness 6-pin connector into the switch harness, and plug the switch harness 6-pin connector into the fuse box. HOLDER 6-PIN DUMMY OTHER ACCESSORY 6-PIN CLIPS (3) DRIVER S DASHBOARD UNDER PIN 46. Plug the switch harness 6-pin connector into the 6- pin connector of the fuse box. 6-PIN FUSE BOX 47. Route the switch harness 5-pin connector (blue) through the body panel opening alongside the vehicle harness. Secure the switch harness to the vehicle harness with one wire tie in the area shown. BODY PANEL OPENING 6-PIN FUSE BOX 5-PIN (Blue) 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 13 of 19

14 48. Behind the steering hanger pipe, locate the 2-pin connector blue-taped to the vehicle harness. Connect the switch harness 2-pin connector to the vehicle 2-pin connector. 49. Attach the switch harness ground terminal to the steering hanger pipe stay with one of the ground bolt supplied. Without a Cruise Control Unit: 2-PIN STEERING HANGER PIPE STAY 2-PIN NOTE: If the 2-pin connector is already being used by another accessory, locate the 2-pin connector taped to that other accessory's harness. Plug the switch harness 2-pin connector into the other accessory's harness. With a Cruise Control Unit: GROUND BOLT GROUND TERMINAL OF Remove and discard the bolt that fastens the control unit, then attach the switch harness ground terminal to the steering hanger pipe with one ground bolt supplied. OTHER ACCESSORY 2-PIN 2-PIN CRUISE CONTROL UNIT STAY 2-PIN BOLT (Discard) GROUND BOLT GROUND TERMINAL 14 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

15 50. On the left of the steering shaft, locate the 3-pin connector black-taped to the vehicle harness, and plug the switch harness 3-pin connector into the vehicle 3-pin connector. 3-PIN STEERING SHAFT 51. Secure the switch harness to the vehicle harness with six wire ties in the areas shown. 3-PIN NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to that other accessory's harness. Remove the dummy connector from that other accessory's harness. Plug the switch harness 3-pin connector into the other accessory's harness. 3-PIN 52. Remove the switch cover from the driver s side dashboard lower cover, and install the switch in the driver's dashboard lower cover. HOLE LID DRIVER'S DASHBOARD LOWER DUMMY OTHER ACCESSORY 3-PIN 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 15 of 19

16 53. If equipped, reinstall the driver's dashboard under cover. HOLDER 55. Check that all wire harnesses are routed properly and all connectors are plugged in. 56. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 57. Reconnect the negative cable to the battery. USE AND CARE How to Operate Fog Lights Turn the headlight switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Fog Light Aiming Adjustment CLIPS (3) DRIVER S DASHBOARD UNDER PIN 54. Plug the switch harness 5-pin connector (blue) into the switch, then reinstall the dashboard lower cover. 58. Adjust the fog light: Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained. AIMING ADJUSTMENT GEAR PHILLlPS SCREWDRIVER 5-PIN OF (Blue) To lower To raise DROVER'S DASHBOARD LOWER 16 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

17 59. Reset the clock, and reset the radio station presets. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 60. Start the engine. Push down on the driver s window switch until the window is fully open. 61. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds. 62. Test the driver's window AUTO function. BULB REPLACEMENT 1. Remove the two 4 x 12 mm washer-screws, and loosen the two 4 x 10 mm washer-screws that fasten the fog light. Pull the fog light out toward you, unplug the connector from the fog light, and remove the fog light assembly. 4 x 10 mm SELF-TAPPING SCREW 4 x 12 mm SELF-TAPPING SCREWS (2) 2. Remove the bulb. BULB 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 17 of 19

18 3. Install the new bulb into the socket. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mind detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. NEW BULB SOCKET 4. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw. 5. Check the operation of the fog light; adjust the aiming if necessary. 18 of 19 AII (0209) 2002 American Honda Motor Co., Inc - All Rights Reserved.

19 CIRCUIT DIAGRAM Under-hood Relay Box HOT WITH HEADLIGHT IN HAED,AND HEAD, AND DIMMER IN IN HIGH HIGH WHT/GRN FR HOT WITH HEADLIGHT IN IN HAED HEAD HOT AT ALL TIMES Fog Light Fuse 20A RED/GRN BLU/RED HOT WITH HEADLIGHT IN PARK OR HEAD Relay RED/BLK BLU 2 1 Switch 1=Indicato 2=Switch Illumination RED Illumination Control GRN BLK Relay BLU/YEL Front Fog Light BLK BLK BLK BLK OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE OFF LIGHT Low Hi BLU BLUE PUR PURPLE GRN GREEN NAT NATURAL RED RED PNK PINK WHT WHITE GRY GRAY OFF ON ON - LT BLU LIGHT BLUE LT GRN LIGHT GREEN 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0209) 19 of T

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDN-100 2004 ACCORD 2-DOOR AII 25735 Issue Date SEP 2003 NOTE: The outside temperature gauge can not be installed in a vehicle