INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Madeleine Austin
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SNA-100D Application 2010 CIVIC 4-DOOR Publications No. AII Issue Date SEP 2009 PARTS LIST Right fog light 6 Wire ties Left fog light Clip Switch harness 2 Self-tapping screws 20A Fuse (Some may not be used.) Fog light harness Relay Subharness Ground bolt Combination light switch 2 Spring nuts 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 08V31-SNA-1D of 12

2 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm and 12 mm Sockets Blanket Diagonal cutters 5 mm Hex wrench Illustration of the Fog Lights Installed on the Vehicle SUB RELAY COMBINATION LIGHT INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft codes for the audio system and navigation system (if equipped), then write down the radio presets. 2. Disconnect the negative cable from the battery. 3. Remove the front bulkhead cover (two expansion clips, three clips, and move the right and left fender trims inward). 3 CLIPS (Pull Straight up.) EXPANSION CLIPS RIGHT FOG LIGHT LEFT 20A FUSE AK PANEL RIGHT FENDER TRIM FRONT BULKHEAD COVER LEFT FENDER TRIM T 2 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

3 4. With the help of an assistant, remove the front bumper (four long clips, four center clips, two socket bolts, and two self-tapping screws). To prevent damage, set the front bumper on a blanket. 6. Install the spring nut onto the front bumper. FRONT BUMPER SPRING NUT SOCKET BOLTS COVER OPENING LONG CLIPS CENTER CLIPS LONG CLIPS FRONT BUMPER 5. Remove the left fog light cover (four tabs). 2 SELF- TAPPING SCREWS AK SELF- TAPPING SCREW LEFT FRONT BUMPER AK 7. Install the left fog light to the fog light cover opening, and secure it with the self-tapping screw. 8. Repeat steps 5 through 7 on the other side. 9. Route the fog light harness 2-pin connector between the lower grille and the front bumper from the right side through the left side. FRONT BUMPER FRONT BUMPER 2-PIN LEFT COVER 4 S AK 2-PIN/4-PIN S FRONT BUMPER LOWER GRILLE AK 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 3 of 12

4 10. Attach the clip on the fog light harness to each hole of the lower grille. 13. Plug the fog light harness 2-pin connector into the right fog light bulb. LOWER GRILLE CLIP RIGHT BULB 2-PIN WIRE TIE LOWER GRILLE LOWER GRILLE RIB AK 14. Install the fog light harness clip onto the lower grille rib. 15. Remove three bolts from the washer reservoir tank. CLIPS (Attach them to the hole on the lower grille.) AK 11. Secure the fog light harness to the lower grille with one wire tie. 12. Plug the fog light harness 2-pin connector into the left fog light bulb. LEFT BULB WASHER RESERVOIR TANK 3 BOLTS AK 2-PIN AK 4 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

5 16. Locate the 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the 1-pin connector. Plug the vehicle 1-pin connector you just freed into the subharness 1-pin connector. 17. Route the subharness between the washer reservoir tank and vehicle panel as shown. PIPE VEHICLE SUB 1-PIN SUB BLUE TAPE (Remove.) VEHICLE PANEL VEHICLE 1-PIN SUB AK WASHER RESERVOIR TANK SUB- GROUND TERMINAL GROUND BOLT VEHICLE FRAME BK 18. Secure the subharness ground terminal to the vehicle frame using the ground bolt supplied. 19. Reinstall the washer reservoir tank. Check that the pipe is installed securely American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 5 of 12

6 20. Secure the subharness clip to the vehicle frame, and secure the subharness to the vehicle harness using two wire ties. WIRE TIES SUB- VEHICLE FRAME 23. If equipped, remove the driver s dashboard under cover by turning the knob counterclockwise, and releasing two clips and pin. Take care not to damage the clips. PIN CLIP SUB 4-PIN SUB- CLIP BK 21. Slide the clip onto the subharness 4-pin connector, and secure it to the vehicle frame. 22. Plug the fog light harness 4-pin connector to the subharness 4-pin connector, then reinstall the front bumper. 2 CLIPS DRIVER S DASHBOARD UNDER COVER KNOB T 24. Remove the driver s dashboard lower cover (eight clips). Take care not to damage the clips. SUB 4-PIN DRIVER S DASHBOARD LOWER COVER 8 CLIPS T FRONT BUMPER 4-PIN AK 6 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

7 25. Lower the tilt lever, and pull the steering wheel toward you. Insert a flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover. 27. Remove the column lower cover (two self-tapping screws and one screw). COLUMN UPPER COVER STEERING WHEEL (Pull toward you.) 2 RETAINING S Push. COLUMN LOWER COVER HOOKS RETAINING COLUMN LOWER COVER RETAINING SCREW SELF-TAPPING SCREWS T TILT LEVER FLAT-TIP SCREWDRIVER GUIDE 28. Push the retaining tab from the vehicle white 34-pin connector, and raise the lock lever from connector. Remove the connector from the fuse box. Close the lock lever on the vehicle white 34-pin connector and remove the cover by sliding it from the connector T 26. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (three retaining tabs). Pull up to remove the column upper cover (two hooks). WHITE 34-PIN Push. Slide. FUSE BOX Push. COVER RETAINING Push. VEHICLE WHITE 34-PIN LOCK LEVER AK 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 7 of 12

8 29. Insert the two switch harness terminals into the white/red terminal and blue terminal of the vehicle white 34-pin connector. 32. Plug the relay into the switch harness relay block, then slide the relay block onto the vehicle bracket stay. WHITE/RED TERMINAL LOCK LEVER RELAY BLUE TERMINAL Harness Side View VEHICLE WHITE 34-PIN VEHICLE BRACKET STAY RELAY BLOCK TERMINALS T 30. Reinstall the vehicle white 34-pin connector. 31. Route the switch harness above the vehicle knee bolster T 33. Locate the 1-pin connector blue-taped to the vehicle harness. Plug the switch harness 1-pin connector into the vehicle 1-pin connector. VEHICLE KNEE BOLSTER 1-PIN VEHICLE 1-PIN T T 8 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

9 34. Secure the switch harness to the vehicle harness and vehicle knee bolster with three wire ties in the areas shown. WIRE TIES VEHICLE KNEE BOLSTER VEHICLE 38. Install the new combination light switch on the steering column using the two screws. Hold the case by hand, then install the new combination light switch to the steering column. Do not push on the lever when installing the case. Push in on the case and securely set the retaining tab into the tab hole. COMBINATION LIGHT STEERING COLUMN VEHICLE 12-PIN WIRE TIE HOLE T 35. Lower the tilt lever and pull the steering wheel toward you. VEHICLE 12-PIN COMBINATION LIGHT STEERING COLUMN COMBINATION LIGHT CASE RETAINING LEVER SCREWS (Reuse.) AK 39. Plug the vehicle 12-pin connector to the new switch. Replace the vehicle harness. HOLE CASE SCREWS RETAINING COMBINATION LIGHT LEVER STEERING WHEEL AK 36. Turn the steering wheel 90 counterclockwise. 37. Unplug the vehicle 12-pin connector from the combination light switch. Remove the two screws from the combination light switch. While pushing the retaining tab, slide the combination light switch out, and remove it from the steering column. Do not pull on the lever when removing the case. Do not damage the tab hole of the steering column American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 9 of 12

10 40. Install the 20A fuse into the fuse box in the location shown. If the fuse is already installed, it is not necessary to install the 20A fuse. USE AND CARE How to Operate Fog Lights Turn the light switch to the position (headlights on low beam). Turn the fog light switch (indicator is on). FUSE BOX FUSE BOX HEADLIGHT OFF Low High 20A FUSE FUSE LOCATION T 41. Check that all wire harnesses are routed properly and all connectors are plugged in. 42. Reinstall all removed parts. 43. Connect the negative cable to the battery and check operation of all lights and other electrical accessories. 44. Enter the anti-theft codes for the audio system and the navigation system (if equipped), and reset the radio station presets. 45. Reset the clock on vehicles without navigation. 46. If the IMA battery level gauge (BAT) displays zero segments, start the engine, and hold it between 3,500 and 4,000 rpm (in Park or Neutral) until the gauge displays at least three segments. OFF ON BK NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Adjusting the Aim 1. Adjust the vertical aiming according to local laws and regulations. To adjust, turn the adjusting screw in or out until the correct angle is obtained ADJUSTING SCREW - - ON - To lower. To raise AK 2. Repeat on the right side. 10 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

11 BULB REPLACEMENT 1. Remove the self-tapping screw, and pull the fog light out toward you. 3. Remove the bulb from the fog light by turning it. SELF- TAPPING SCREW BULB AK AK 2. Push in the retaining tab, and unplug the connector from the fog light. RETAINING (Push.) LEFT AK 2009 American Honda Motor Co., Inc. All Rights Reserved. AII (0909) 11 of 12

12 4. Install a new bulb on the fog light by turning it clockwise until it stops. Take extreme care when replacing the fog light bulb to avoid damaging the lenses or finished surfaces of the body. Use only a Honda Genuine halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers. Turn the bulb until it stops. NEW BULB AK 5. Plug the connector to the bulb. 6. Install the fog light in the reverse order of removal. 7. Check that the bulb comes on properly. Adjust the aim as necessary. 12 of 12 AII (0909) 2009 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory S Application 2010 CIVIC 2-DOOR EX-L Publications No. AII 42488 Issue Date AUG 2009 PARTS LIST P/N 08V31-SVA-110G Right fog light Clip 4 Spring nuts Left fog light 4