Tesla Model S Rear Lighted T
|
|
- Hubert Pitts
- 5 years ago
- Views:
Transcription
1 Tesla Model S Rear Lighted T Installation Instructions The rear lighted T makes your Tesla Model S distinctive if not unique from other cars on the road and other Model S s. This LED powered device is mounted under Tesla s standard chrome T and arch on the rear of the car. When the car s running lights are on the T will light red in with a color and intensity that almost perfectly matches the running lights. When the brakes are applied the T brightens to an intensity equal to the brake lights, reminding cars behind you that you are driving a very special vehicle. TESLA MODEL S REAR LIGHTED T INSTALLATION 1
2 Parts Provided Rear"Lighted"T"and"Arch"with"dual"brightness"drive" 5 feet each of blue, yellow, and black 20 gauge stranded wire Three gauge Posi-taps 5 Posi-Lok Connectors, gauge 2 feet Spectra nylon parachute thread 5 spare blue/green plastic retainer clips Small tube of clear silicone sealant" TESLA MODEL S REAR LIGHTED T INSTALLATION 2
3 A. Remove liftgate trim pieces There are four black plastic trim pieces on the interior side of the lift gate: top, right and left sides, and a large piece covering the lower side of the liftgate. Each is clipped into place with plastic retainers that snap into a hole on the lift gate metal frame. These must be removed to proceed with the installation. 1. Begin with the top horizontal piece. Using a plastic pry tool or your hands, snap the right or left side loose and remove the piece. Some of the clips may break or remain stuck in the mounting hole. In the latter case use a u-shaped pry tool to remove them. Save all the clips that have not been damaged you ll need them for the re-installation. Replace any broken clips with those in the parts list. 2. Do the same with the right and left pieces. 3. Removal of the large bottom trim piece requires several additional steps. First, the two indented handle openings at the bottom of the piece have to be removed using a pry tool. The passenger side piece has a wire connection for the lift gate release. Unplug it. The upper ends of the trim piece are attached to the lift gate frame with small black screws. Remove these screws. 4. At this stage there are two alternatives. You can prop up the large lower trim piece while you install the rear T or you can disconnect the trim piece s electrical connections and set the piece aside. The former option is a bit easier but requires an assistant and material to hold the trim piece up while you install the rear T and make its electrical connections. Point 5 below describes the steps for the latter option. This piece also had two T-15 screws holding it in place a the top ends be sure to remove them. 5. The lower trim piece has several electric connections on the back side: one each for the two rear speakers, and one TESLA MODEL S REAR LIGHTED T INSTALLATION 3
4 for the trunk light. Accessing these connectors is much easier if the speaker mount piece at the top is removed, which is clipped in place. Starting with the bottom edge work the trim piece loose but hold it loosely in place once all of the retaining clips have been released, taking care not to stress or break these electrical connectors. Reach up over the inside of the trim pieces to disconnect these. The top piece can be problematic as it has a small retaining tab on the upper side of the connector connections. 6. Once all of the trim pieces have been removed set them aside in a safe place and keep all of the retainers and screws in a place where they will be easy to find for reuse. 7. When the pieces have been removed you ll see two black vinyl sheets on the back of the lift gate. These are glued on with a tar-like material and need to be removed to provide access to the electrical connections. Remove them and set aside B. Mount the rear lighted T 1. Raise the lift gate to a convenient working level for working on the T. 2. Using the painters tape outline the existing chrome T and arch to mark their exact placement. This is a very important step for correct placement of the lighted T and arch. 3. Using your fingers push the chrome T and arch from side to side to loosen them a bit from the double sided tape with which they are attached to the lift gate. 4. Take a 12 piece of parachute thread and use it to saw back and forth under the chrome T until it s loose and you can remove it. Do the same for the chrome arch. Set them aside in a safe place. The residue of TESLA MODEL S REAR LIGHTED T INSTALLATION 4
5 the black double sided tape that attached the T and arch to the lift gate will remain when the chrome pieces have been removed. Leave this on the car as is and do not attempt to clean it off. It serves as a guide for drilling the holes for the electrical connections and mounting the lighted T and arch. 5. With a marker, place a spot on the residue double- sided black tape about 1/8 from the extreme right edge of the top of the T, centered in the space from top to bottom. Do the same on right edge of double-sided black residue tape for the arch. These are the guide marks for drilling the hole. Take the light T and arch pieces and match the wire placement on the backs to be sure the marks are accurate. 6. With the drill and bit and using light pressure on the drill very carefully drill a hole in these spots. The residue double-sided tape will keep the drill bit from drifting. As soon as the drill penetrates the sheet metal stop drilling and back out the drill. 7. Take the T and thread the red and black wire lead through the hole you just drilled. Find the lead on the underside of the lift gate and temporarily tape it to the lift gate back. Do the same with the arch. 8. Remove the protective covering from the 3M double side tape on the back of the T and carefully but lightly align it in place over the black residue double sided tape. painters tape also helps) then press it firmly into place. Do the same with the arch, being sure to maintain good, even spacing between the top edge of the T and the bottom edge of the arch. 9. Once you re happy with the alignment of the T and arch remove the protective tape from the top of the lighted T and apply the original Tesla chrome T on top of it, taking care to align it perfectly. Once aligned press it firmly into place. Do the same with the arch. TESLA MODEL S REAR LIGHTED T INSTALLATION 5
6 C. Connect the running and brake light 12v power 1. Locate the black and red leads for the T and arch on the underside of the lift gate, Using the tube of silicone place a dab (for water proofing) on the back of each hole then separate the red and black wires.. Strip about 1/2 inch of the insulation off the ends. Twist together the 2 red wires and do the same with black wires. Then attach a Posi- Lock Connector on the ends of both the red and black wires. Then take the red and black leads on one end of the dual brightness driver and attach them to the open ends of the Posi-Lock Connector attached to the red and black leads from the T &. Arch. Leave the yellow, blue, and white wires from the dual brightness driver alone they will be connected in the steps below. If additional lengths of wire are needed to make these connections, use the wire provided in the kit and the Posi-Lock Connectors. 2. Look at the very top of the underside of the lift gate. You ll see a black cable with a reddish pink connector. This cable contains both the LED brake light and ground connections 3. Trace this cable down the underside of the lift gate. You want to access it in the passenger side opening that was revealed when you removed the black vinyl pieces in step A5. Find the cable in this opening then pull out so that it s accessible. Then remove some of the electrical tape and open it up so you can access the individual wires in the cable. The blue wire is for the brake light connection and the black wire for ground. 4. Place a Positap connector on the blue wire and slip the yellow lead from the dual brightness driver into other side of the connector and screw both ends down as tight as possible. TESLA MODEL S REAR LIGHTED T INSTALLATION 6
7 5. Place another Posi-tap connector on the black wire and slip the white lead from the dual brightness drive into the other side of the connector. Then screw down both ends as tight as possible. 6. Just behind the license plate lights on the interior side of liftgate you ll find purple wires that provide power for each license plate light. Attach a Positap to one of the purple wires and connect the blue wire from dual brightness driver to the other end of the Positap. 7. You re now ready for testing. D. Test Operation You will need an assistant for these steps. 1. Using the touchscreen turn all of the lights on. The rear lighted T should light match the intensity of the rear running lights. If it doesn t light check all of your connections. 2. Have an assistant sit in the car and press the brake light. The rear lighted T should brighten to match the intensity of the brake lights. The video to the right shows proper operation TESLA MODEL S REAR LIGHTED T INSTALLATION 7
8 3. Turn on the hazard warning lights. The rear lighted T should flash in sync with the other lights. E. Reinstall liftgate trim pieces This is the most difficult step of the install and unless you have extensive experience and skill with mounting large trim pieces with plastic clip retainers we recommend you leave this work to an installation professional such as an auto aftermarket sound-system shop. If you want to attempt this yourself will need an assistant. Help is essential for reinstallation the large trim piece, as it has to be held up in place while the cable connections are remade. If you ve disconnected the electrical connectors on the large trim piece, below is a guide for the reconnections: Warning note: The wiring for the rear two speakers has the same connector as the trunk light. You could accidentally plug in the 12 volt supply to the speaker so be careful to follow these connections: Drivers side speaker: Light blue with black stripe Passenger side speaker: Light Green with Black stripe Trunk light -Black with white stripe TESLA MODEL S REAR LIGHTED T INSTALLATION 8
EVANNEX Rear Lighted T for Tesla Model X
EVANNEX Rear Lighted T for Tesla Model X Installation Instructions The Evannex Rear Lighted T gives your Tesla Model X a distinctive look. This LED lighted device is mounted under Tesla s OEM chrome T
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 30250 UNDER SPOILER 2006 RSX Issue Date JULY 2005 PARTS LIST Rear under spoiler 5 Stepped bolts 2 Bolts 7 Flange nuts, 6 mm 3 Square
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2009 Toyota RAV-4 Stainless Steel Mesh Grilles L 30 G8P Fine Mesh Part #30-002-09 Quantity Description Part No. Upper Mesh Grille (includes):
More informationGen II Tesla Model S Lighted Rear Applique. Installation Instructions
Gen II Tesla Model S Lighted Rear Applique Installation Instructions Parts Needed Gen II aluminum lighted Rear Appliqué with Bluetooth controller (purchase on evappliques.com) Parts provided with the Appliqué
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More informationINSTALLATION GUIDE Front Bumper. KL Cherokee (Trailhawk)
INSTALLATION GUIDE Front Bumper KL Cherokee (Trailhawk) Included Hardware: Sample Sample Sample Skill Level: 5/5 stars (Professional install recommended) Disclaimer Expedition One is not responsible for
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationInstallation of a Tekonsha Prodigy P2 Trailer Brake Controller in a 2016 Tesla Model X
If you received a copy of this document from any source other than http:// www.adelman.com/model-x-brake-controller.pdf, please go to this URL and download the latest version of this document. Want to
More informationMustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC #
1990-1993 Mustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC # 101000 Kit Components: 1 Light Bar 4 Bolts ( 5 / 16-18 x 2.5 ) #182010 4 Washer #182005 4 Shims #182009 2 Dark Blue Connectors #182004
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationPowerstroke 6.4L EGR Block Kit
Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** You will need the following tools for this installation: 10mm wrench 13mm wrench
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 31129 REARVIEW CAMERA 2006 RL Issue Date OCT 2005 PARTS LIST Attachment Kit P/N: 08B21-SJA-B00 Template Rear camera trim 6-Pin connector
More informationInstallation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationRaxiom Mustang Headlights (94-98) - Installation Instructions
Raxiom Mustang Headlights (94-98) - Installation Instructions The below installation instructions work for the following products: Dark Smoked Mustang Headlights (94-98) Raxiom Chrome Mustang Headlights
More informationPump Gas Instructions for Polaris And 800 Models. Important Information before Installing This System:
Pump Gas Instructions for Polaris 600 700 And 800 Models Important Information before Installing This System: Before you begin your turbo install, read through these instructions to determine if you are
More informationInstructions for Front Midrange Installation in BMW 3 Series/M3 Coupe, Cabrio without Harman Kardon Audio System (E46)
Disclaimer: Bavarian Soundwerks highly recommends professional installation of the products we sell. We provide these installation instructions free of charge as a guide to assist those customers who choose
More information= Experienced
I N S T A L L A T I O N G U I D E APPLICATION LENGTH MODEL YR PART # Ford F-250 / F-350 / F-450 Regular Cab * (48 ) 2002-2003, 2008-2012 75134-01A Ford F-250 / F-350 / F-450 Super Cab * (60 ) 2002-2003,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 27035-29095 2005 RL Issue Date MAY 2005 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 33590 2007 RL Issue Date AUG 2006 PARTS LIST Trunk spoiler Right support strut Left support strut 4 Washer-bolts 4 Adhesive seals TOOLS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 40454 XM SATELLITE RADIO 2009 S2000 Issue Date AUG 2008 PARTS LIST Template XM Radio Unit Kit (sold separately): P/N 08A53-S2A-101 XM
More informationMustang One-Touch Convertible Top Module (2005+) - Installation Instructions
Mustang One-Touch Convertible Top Module (2005+) - Installation Instructions The below installation instructions work for the following products: Mustang One-Touch Convertible Top Module (2005+) Please
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More information1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and f
STRUT 2015 GMC Denali Collection Installation Manual " 1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationInstructions for Front Midrange / Tweeter Installation in BMW 3 Series/M3 (E36)
Disclaimer: Bavarian Soundwerks highly recommends professional installation of the products we sell. We provide these installation instructions free of charge as a guide to assist those customers who choose
More information80703 & Backside License Plate Mount for Jeep JK Wrangler (80707) & 10+ (80703)
80703 Backside Mount 80707 Backside Mount REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH
More informationInstructions for installing Extendable Replacement Mirrors for Ford HD vehicle.
Instructions for installing Extendable Replacement Mirrors for Ford HD vehicle. Manual CIPA # 82100 Right Hand #82110 Left Hand #82111 Electric CIPA # 72100 #72110 #72111 Heated / Electric CIPA # 72500
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera
More informationRetrofit Steering Column
Retrofit Steering Column INSTALLATION INSTRUCTIONS for 1970-75 Camaro FOR PART NUMBER S: 1620860010, 1620860020, 1620860051, 1626860010, 1626860020, 1626860051 S INCE 1986 www.ididitinc.com 610 S. Maumee
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More information2010 to 2013 Toyota 4runner Rear bumper installation instructions:
2010 to 2013 Toyota 4runner Rear bumper installation instructions: Note: This is one of the most difficult bumpers we product to install. The installation of this bumper requires cutting of the current
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (740-754) Ford F-Series Pickup & Bronco 1980 96 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationTESLA MODEL S REFRESH FRONT FASCIA INSTALLATION MANUAL FIGURE 1. Unplugged Performance 3523 Jack Northrop Ave, Hawthorne, CA 90250
INSTALLATION MANUAL TESLA MODEL S PARTS QUANTITY INCLUDES FRONT FASCIA 1 PIECE V-STRIPE PANEL 1 PIECE HARDWARE KIT 1 SET PDC SENSOR HOLDERS 4 / 6 PIECES HOOD RELEASE KIT 1 KIT REFRESH FRONT FASCIA PLEASE
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationR-1125 C HARNESS MOUNT BAR INSTALLATION INSTRUCTIONS Fits C7 Corvette Coupes, including Z06
R-1125 C HARNESS MOUNT BAR INSTALLATION INSTRUCTIONS Fits C7 Corvette Coupes, including Z06 The R-1125 Harness Mount Bar has been designed and tested to provide a mounting point for the shoulder harness
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More information- MK7 Mirror Integration Kit - Installation Instructions
- MK7 Mirror Integration Kit - Thank you for choosing the Double Apex Gentex Mirror Integration kit for your Volkswagen MK7. If you have any questions about the installation please email us at support@dblapex.com.
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationTools Needed: 7mm Socket socket wrench socket extension interior removal tool wire cutter electical tape Wrangler Raxiom Navigation
2007-2010 Wrangler Raxiom Navigation Contents: (1) - Raxiom Head Unit (1) - Headphone Jack With Wire (A) (1) - GPS Antennae With Wire (B) (1) - Amplifier Pre-Outs Wire Harness (C) (1) - External Microphone
More information1) Remove side panels. Remove clutch cover. Remove windshield by pulling up on the three posts secured into
UNDER HOOD HEAT ELIMINATOR A.K.A. THE BLOW HOLE by Mountain Tek Application 2013 Model Year SKIDOO XM Kit Contents 1) (1) Fan Tube Assembly 2) (1) Accessory Connect Harness 3) (1) Fan Vent Cover Plate
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (665-2542) Ford F-Series Pickup & Bronco 1980 96 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM S2000 AII 26324 Issue Date OCT 2004 PARTS LIST Headrest Speaker System P/N 08A54-S2A-100 3 Small wire ties 2 Headrest speakers 9
More informationBackside License Plate Mount for Jeep JK Wrangler
REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH LEDS PLASTIC PASS-THROUGH GROMMET STAINLESS
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC
More informationHUMMER H A. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL. 4= Experienced TOOLS REQUIRED APPLICATION MODEL YR PART #
INSTALLATION GUIDE APPLICATION MODEL YR PART # HUMMER H2 2003-2009 75107-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED Safety goggles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28593 2006 RIDGELINE P/N 08F23-SJC-100 Issue Date FEB 2005 PARTS LIST Center front bumper trim (Not used if the vehicle is equipped
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal: Release these clips
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationAir Conditioner for M915 A0/A1 Truck
RD-2-4530-0 Air Conditioner for M915 A0/A1 Truck INSTALLATION INSTRUCTIONS Install refrigerant compressor per instructions provided with compressor mount kit. CAUTION: Edges of sheet metal can be sharp!
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM ACCORD 2-DOOR (LX/EX L4, LX V6) AII 25749 Issue Date FEB 2004 PARTS LIST Double-sided adhesive tape XM Radio Attachment Kit : P/N
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 37371 SPOILER 2008 TL Issue Date JUN 2007 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Template A TOOLS AND SUPPLIES REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-110 2007 CIVIC 2-DOOR All33536-34848 Issue Date FEB 2007 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra
More informationFRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS
FRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS TOOLS NEEDED 13mm socket 5/32 Allen head 5/16 wrench or socket 7/16 wrench or socket 7/32 Allen head 5/8 wrench
More informationTIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT
Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT TIP SHEET T0937 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself installers
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationFRONT BUMPER REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. Disconnect Battery.
Parts included (1) - Main Full Opening - Polished - Part #6202130 Full Opening - Black - Part #6202131 OR GRILLE REMOVAL & Grille Installation Guide Hardware included (5) - Trim Retainer (4) - 1/2 x 1/2-3/16
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK (WITH MOON) Application 2009 PILOT Publications No. AII 39492 Issue Date MAY 2008 PARTS LIST HFL Attachment Kit 2 Washer screws, 4 x 12 mm HFL
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26042-26353 XM INTERFACE ODYSSEY EXCEPT EX-L WITH NAVI/RES Issue Date FEB 2004 PARTS LIST 8 Wire ties XM Radio Attachment P/N 08B15-S0X-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REAR VIEW CAMERA ATTACHMENT PILOT AII 23620 Issue Date MAY 2002 PARTS LIST Attachment Kit : P/N 08B21-S9V-100 Control unit harness Rear
More information(1) License Plate Light (2) License Plate Plugs
PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure
More informationConflicts None. TOYOTA TUNDRA 2017 Black Laser Cut Grille. Part Number: Accessory Code: BG3000. General Applicability
TOYOTA TUNDRA 2017 Black Laser Cut Grille Part Number: 00016-34173 Accessory Code: BG3000 Conflicts None Kit Contents Item # Quantity Reqd. Description 1 1 Laser Cut Grille 2 1 Complete hardware kit General
More informationPRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver
Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationINSTALLATION INSTRUCTIONS
Rear Vision System NAV Display 2009-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9501) Kit Contents: Camera/Module/Bezel Assembly Chassis Harness NAV Harness 1
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More information2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions
2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationSTART HERE FRONT BUMPER REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. Disconnect Battery.
Parts included (1) - Main Full Opening - Polished - Part #54213 OR Full Opening - Black - Part #51213 Hardware included (10) - #10 Screws (10) - #10 Flat Nuts (2) - Thread Cutting Nuts OR START HERE PLEASE
More informationGo-ped ESR750 / ESR750EX Rear Brake Installation Instructions
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2011 PILOT Publications No. AII 43298 Issue Date MARCH 2010 PARTS LIST Back-up Sensor Attachment Kit P/N 08V67-SZA-100A Back-up sensor harness Fuse label
More informationRear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number )
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2004 CR-V AII 26118 Issue Date SEP 2003 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9A-100
More informationInstallation Instructions StarShifter
Installation Instructions StarShifter Part Number 80675 2000 by B&M Racing & Performance Products LLC The B&M StarShifter can be used in vehicles equipped with most popular three speed automatic transmissions.
More information2002 Convertible Cloth Sleeve Convertible Cloth Attachment
2002 Glass Convertible Top on 2000-2001 Frame Submitted by Clovis, North Texas S2000 Owners Club So what s the difference? Honestly, not much. The 2000 soft top cloth has attachment points for each of
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2012 CROSSTOUR Publications No. AII 46198 Issue Date JULY 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TP6-101 Upper spacer A (5 mm) (Some are not used.)
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More information