Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good t
|
|
- Evelyn Carroll
- 6 years ago
- Views:
Transcription
1 How to make a ROV!
2 Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good to have extras. Using the wire cutter, strip about ¼ inch of insulation off of each end of the wires. Apply an electrical fork terminal (16-14 AWG) to each end of the wires. With the crimping tool, secure the fork to the wire. For additional security, solder each connection between the electrical forks and the wires. Follow the instructions included with the soldering tool. Set the wires aside for now.
3 Step#2 Drill three ½ inch holes in the lid of your conduit box in a triangular pattern as shown. Now drill one 5/8 inch hole and two additional holes in the front of the conduit box as shown. The size of the two smaller holes will depend on the thickness of your tether cable and power cord.
4 Step #3 Open your three (ON) OFF (ON) toggle switches and remove the rings and nuts. Insert the toggle switches through the lid of the conduit box so that they align as shown. Secure the toggle switches to the conduit box by placing the rings and nuts on the top of the switches and tightening with the wrench and pliers. If it looks like there are any gaps in the lid, apply a bit of hot glue around the base of the toggle switched to ensure that the lid is waterproof.
5 Step #4 Loosen the screws on the end of each toggle switch. Now, using six of the wires you prepared earlier, attach them to the toggle switches in a cross ways manner as shown and re-tighten the screws. You may have to reposition the wires at a later time if they prevent you from closing the conduit box. If so, just loosen the screws and bend the wires out of the way.
6 Step #5 Gather three more of the prepared wires, three fork terminals, and one female push on terminal. Attach an electrical fork terminal to the end of one of the wires Now, twist the other end of that wire together with the end of another wire. Attach another electrical fork to this junction. Twist the free end of this wire together with a third wire and attach another electrical fork at this junction. Finally, attach the female push on terminal to the free end of the third wire. Each of these connections should be reinforced with the soldering iron. The finished product should look like this.
7 Step #6 Take two more of the prepared wires and three electrical fork terminals. Attach an electrical fork terminal to the end of the first wire. Twist the other end together with the other wire and attach an electrical fork to the junction. Finally, attach another electrical fork terminal to the free end to the second wire. Again, each of these connections should be reinforced with the soldering iron.
8 Step #7 Using the longer set of wires and starting with the end nearest the female terminal, attach the first electrical fork to the left side of the first toggle switch (the one at the top of the triangle) as shown. The female terminal should be left dangling Attach the next fork terminal to the left side of the second toggle switch as shown. Finally, attach the third electrical fork terminal to the right side of the third toggle switch as shown
9 Step #8 Now, grab the other set of wires. Begin by attaching the first electrical fork to the right side of the first toggle (at the top of the triangle) as shown. Next apply the second electrical fork to the left side of the second switch as shown Attach the final electrical fork terminal to the right side of the third toggle switch.
10 Step #9 Insert one end of your six wire cable tether into one of the smaller holes on the end of the lower half of the conduit box. Strip off about three inches of the outer shell of this cable. You may need to use scissors or a razor blade to do this if your crimping tool does not work. If so, slowly cut around the cable and try to avoid cutting any of the inner wires. Strip each of the six interior wires about ¼ - ½ inch. Apply an electrical fork terminal to each. Solder these connections.
11 Step #10 Loosen the bottom two screws on each of the toggle switches to allow a second electrical fork. Now, separate the six wires into three different pairs of two. It does not matter which two colors you pair, but write down the pairings as it will be important later. Attach the first pair of wires to the bottom of the first switch as shown. Attach the second pair of wires to the bottom of the second switch as shown. Lastly, attach the third pair of wires to the bottom of the third switch
12 Step #11 Take the heavy duty speaker cable and cut off about ten inches to use later. Insert the long piece into the second hole in the bottom of the conduit box. Separate the two wires by tearing them apart about 3-4 inches. Strip the end of each wire about ¼ inch. Attach a AWG ring terminal to one of the wires and a female push on terminal to the other wire. Solder each of these connections. Remove the screw from the right side of the toggle switch at the top of the triangle. This terminal will already have a wire connected to it, but add the ring terminal and then re-attach the fork terminal and tighten the screw
13 Step #12 Unscrew the fuse holder and insert the fuse by pushing it into the bottom as shown. Re-screw the fuse holder. Remove the nut and washer from the fuse Insert the fuse through the 5/8 inch hole, replace the nut and washer and tighten into place. There are two metal connections on the fuse, make sure the one on the side of the fuse is facing up, towards you.
14 Step #13 Find the end of the power cord with the female push on terminal and attach it to the connection on the end of the fuse as shown. Now, attach the other female push on terminal from the first series of wires to the connection on the top of the fuse. Solder both of these connections and once cool, wrap the connections in electrical tape to prevent them from touching anything else. You may now close your conduit box. Be sure to screw the top on very tightly as to ensure that the box is waterproof. Remember that you may need to bend some wires out of the way or readjust some of the connections If there are any gaps between the wires and the holes, apply a bit of hot glue to ensure that the juncture is waterproof.
15 Step #14 Locate the free end of the two strand power cord. Again, separate the two wires by pulling them apart about three inches. Now strip each wire about ¼ inch. Attach the solder-less banana connectors following the instructions on the package. These will be left alone for now.
16 Step #15 Now it is time to assemble the propellers and attach them to the motors. Line up all of the necessary parts. You should have a prop shaft, drive dog, electric flex hex, and a propeller. If you look at the prop shaft, you will notice that there is a part of the shaft that is threaded. You will need to remove this portion of the shaft. There are two ways to do this: first, you could use a hack saw to cut off this portion, secondly you could use the bolt cutter part of the crimping tool to remove this. If you opt to use the bolt cutters, be very careful not to pinch your hands and watch for flying parts. Next, take the flex hex and unscrew the two pieces and loosen the screw at the bottom with an Allen wrench Insert the prop shaft into the larger portion. Slip the second piece of the flex hex onto the prop shaft and tighten. You will need to use two pairs of pliers to really tighten this connection. Now, slide the propeller onto the prop shaft with the slotted side pointed up. Finally, slide the drive dog onto the prop shaft so that the notches are pointing down and fit into the slots on the propeller. Place the screw into the appropriate hole and tighten with the Allen wrench. In order to attach the completed propeller ensemble to the motor, you will first need to remove the plastic disk at the end of the motors. Slip the end of a screw driver or other flat object under the disk and ease it off. Place the propeller on the motor as shown and tighten the small screw with the Allen wrench. Set the prepared motors aside for a moment.
17 Step #16 Grab the other end of your 6-wire tether. Strip off about three inches of the outer shell as you did before. Strip each of the six inner wires about ½ - ¾ inch as before and put them in groups of two, remembering to pair the same colors together as you did in step 10. Take the three motors and twist the two attached wires together as shown. Now, strip the ends of attached wires about ½ ¾ inch, if not already stripped. Twist together each pair of wires from the motor with a pair of wires from the tether. A pair of needle nose pliers is very helpful in this process. Once each set of wires are twisted, solder the connection so that they do not come apart. When all three sets of paired wires are connected, wrap the connections in electrical tape to prevent the wires from touching one another.
18 Step #17 Wrap the entire collection of cords in several layers of electrical tape to ensure that the area is waterproof. Using the hot glue gun, apply a bit of glue to the end of the tether where the motor wires enter the electrical tape tube. This will waterproof the entrance of these wires. Secure a zip tie to the tube just below the entrance
19 Step #18 Cut six 3 inch pieces of PVC pipe and drill a small hole in one end of each pipe. To help prevent slipping, wrap each motor with a few layers of electrical tape as shown. Attach one 3 in. PVC pipe to the opposite side of each motor using the zip ties. Loop the zip tie through the drilled holes, around the motor, and tighten
20 Step #19 Find the 10 inch piece of power cord you cut off and set aside earlier. Split each end about 3 inches. Strip each wire about 1/4 inch To one end of the power cord, attach two extra large ring terminals as shown. Solder these connections. To the other end, attach the female ends of the banana connectors. This piece of cord will be used to attach the ROV to the battery source when you are ready.
21 Step #20 At this point, you are almost ready to start building your ROV frame. But first, it would be helpful to make a note of which switch controls which motor. Attach the ring terminals to the battery; red is positive and black is negative. Plug the banana connectors into their appropriate female terminals. Turn on the first switch and make a note of which motor it controls. Place a piece of colored electrical tape on the switch and its corresponding motor. Do the same for the other two switches and motors.
22 Step #21 This step is up to you. Now that your three motors have a piece of PVC attached to them they can fit into your frame anywhere. Build yourself a custom frame from your PVC pipe and position the motors to best improve mobility. There are many different designs that will all have ups and downs, it is your job to find the perfect shape. It is easiest to use the two rear switches/motors for forward thrust, reverse and turning and use the third motor for lateral control.
The Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationFigure 1. A CheapBot Robot
A CheapBot controller needs a robot body to function. An ideal robot body for the beginner consists of two sheets of Syntra plastic, separated by four bolts. The bottom deck contains the robot controller
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationROV S IN A BUCKET. ROVs In a Bucket
ROV S IN A BUCKET This document has been prepared for those interested in building ROV s (Remote Operated Vehicles Underwater Robots). Contacts for purchasing the pieces to create the ROV are provided
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationInstallation Instructions
Instructions Created by an: DIY Underhood LED Lighting Kit (SKU# DIY-E-UHLK) Installation Instructions NOTICE: This Under Hood Light Kit was installed on a 2002 Toyota Tacoma. However, these instructions
More informationLED Driving Light Set For 2014 & Newer Can-Am Spyder RT # CA006-RT
LED Driving Light Set For 2014 & Newer Can-Am Spyder RT # CA006-RT 1. Lay-out and familiarize yourself with the components supplied with this set. 2. Remove the left mirror by pulling firmly outward on
More informationBuild Manual. for Studying Electrical Conductivity using a 3D Printed 4-Point Probe Station
Build Manual for Studying Electrical Conductivity using a 3D Printed 4-Point Probe Station 1 Materials 1. 3D printed parts Head support Trigger Front Probe head panel Right panel Middle panel Left panel
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationInstallation of Raxiom Switchback Turn Signal Conversion Kit w/resistors
Installation of Raxiom Switchback Turn Signal Conversion Kit w/resistors Overview: Below are the steps involved in the installation of the Raxiom Switchback Turn Signal LED lights in the 1987 1993 Ford
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationOpenROV. Tether Reel from Cheap Extension Cord Reel
OpenROV Tether Reel from Cheap Extension Cord Reel In this guide I will show you the steps I took to modify a cheap extension cord reel into a tether reel. Written By: Brett Forsyth 2017 openrov.dozuki.com
More informationMustang Headlight w/ CCFL Halo (05-09) - Installation Instructions
Mustang Headlight w/ CCFL Halo (05-09) - Installation Instructions The below installation instructions work for the following products: Chrome Mustang Headlight w/ CCFL Halo (05-09) Smoked Mustang Headlight
More informationBruce s Science workbench
Baby Vandegraff Generator by Bruce Yeany 2001 https://www.youtube.com/watch?v=parq01q DKe4 http://www.instructables.com/id/van-de- Graaff-Electrostatic-High-Voltage- Generator/ https://www.youtube.com/watch?v=esz
More informationZ8 Engine Start Button Install for the BMW E46 3 Series
Z8 Engine Start Button Install for the BMW E46 3 Series This write up is a specific installation of a Z8 engine start button on the E46, but it can be used as a general guide for an engine start button
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationJob Sheet 6 Installing the Combiner Box
Job Sheet 6 Installing the Combiner Box The Combiner Box The combiner box used in this course can combine photovoltaic (PV) solar sub-array strings that are up to 150 V DC each and up to 120 A total. Using
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationBLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES
BLUE LIGHT FOR DYNACO STEREO 120 OR PAT-4 ROCKER SWITCHES 2012 AkitikA, LLC All rights reserved Revision 1p3 April 18, 2012 Page 1 of 15 Table of Contents Table of Contents... 2 Table of Figures... 2 Section
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationBLUE LIGHT FOR DYNACO STEREO 120, SCA-80, OR PAT-4 ROCKER SWITCHES
BLUE LIGHT FOR DYNACO STEREO 120, SCA-80, OR PAT-4 ROCKER SWITCHES 2014 AkitikA, LLC All rights reserved Revision 1p5 April 8, 2014 Page 1 of 16 Table of Contents Table of Contents... 2 Table of Figures...
More informationSpectra C3 Light Bar Installation Instructions
Light Bar Hardware Tools Required Universal Clamp Inserts 1.9, 2 3/8 - OD 5 Amp Fuse 1.25 Hole Saw Philips Screw Driver 7/64 Drill Bit Fish Tape Countersink Pencil Pigtail Wiring Harness Clamp Washer Wire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FST KIT FOR PORT INJECTION 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed
More informationHow to Repair an Apple AC Adapter Broken
How to Repair an Apple AC Adapter Broken Cable Learn how to repair a damaged AC Adapter cable. Written By: Angela Penaherrera ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION Sometimes the cable
More informationUpgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki.
SeeMeCNC Guides Upgrade v3 to v3.2 Rostock Max v3 Uprgade to v3.2 Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 34 INTRODUCTION This guide is intended to Upgrade a Rostock Max v3 to a Rostock
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part# 69-0717 AIR IT UP 4 Tire On Board Installed Air Delivery System with Rear Mounted Controller (Requires External Air Source) For the most up-to-date instructions please visit
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationSection 5: Parts Replacement
Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major
More informationINSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document#
d INSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document# 19-0077 Brie Tech Support: info@radiumauto.com CAUTION: Exercise extreme caution when working with the fuel
More informationNMNGMC MODULE LIGHTS
Material required for one 4 foot module: NMNGMC MODULE LIGHTS 2 each - Hampton Bay, R20 Black Step Cylinder Track Lighting Model #EC735BK, Home Depot Store SKU # 680-247. 1 package - EcoSmart 60W Equivalent
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More information(31 ) ZEON CONTROL PACK RELOCATION KIT
ORIGINAL INSTRUCTIONS SYMBOL INDEX (31 ) ZEON CONTROL PACK RELOCATION KIT SYMBOL EXPLANATION Read All Product Literature SYMBOL EXPLANATION Always Wear Leather Gloves INSTALLATION GUIDE Always Wear Hearing
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationThis LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506.
L.E.D. INSTRUCTIONS I D T S O T U B I R M O C R Y N A P Kit contains: This LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506. For the power supply: 1-LED power supply circuit board, 2
More informationZip Tie Domes - 3V 3/8 Assembly Manual
Zip Tie Domes - 3V 3/8 Assembly Manual Instructions for Assembling the 25 Foot 3V 3/8 Frequency Geodesic Dome Tools Needed: 8 foot Step Ladder, Wire Cutters SAFETY RULES: Do Not Climb On the Dome. It is
More information#GL18006-L2 Honda Gold Wing 1800 & F6B models - All Years Lower Cowl LED Driving Lights INSTALLATION INSTRUCTIONS
#GL18006-L2 Honda Gold Wing 1800 & F6B models - All Years Lower Cowl LED Driving Lights INSTALLATION INSTRUCTIONS 1. Lay out and familiarize yourself with the parts included in the set. Remove the left
More informationDYNACO STEREO 120 C7 REPLACEMENT MANUAL
DYNACO STEREO 120 C7 REPLACEMENT MANUAL 2013 AkitikA, LLC All rights reserved Revision 1p03 April 29, 2013 Page 1 of 15 Table of Contents Section 1: About This Manual... 3 Who Should Attempt this Project?...
More information60-90 EXTRA 260/300 DLE 20 INSTALLATION GUIDE
60-90 EXTRA 260/300 DLE 20 INSTALLATION GUIDE This engine installation addendum will outline the installation of the new DLE 20cc in the 60-90 Extra 260 and Extra 300. The Extra 300 is shown however the
More informationInstructions for MB832 Manual Barrier Ver0614
Instructions for MB832 Manual Barrier Ver0614 Read all the instructions before starting It is recommended that Locktite Blue brand thread sealant be used for all arm and pivot bolts as added protection
More informationFord 6.7L Installation of the Guardian Safety System
Ford 6.7L Installation of the Guardian Safety System Diesel Tech Industries Ltd. 14215-120 Avenue Edmonton, Alberta, Canada T5L 2R8 Phone: (780) 455-9876 info@dtiguardian.com www.dtiguardian.com DTI05-02.01/13
More information8. Electronics assembly (B3/R2 design)
8. Electronics assembly (B3/R2 design) Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 31 Step 1 Tools necessary for this chapter Needle-nose pliers for zip tie trimming. 2.5mm Allen key for
More information5830 Skylight, Solar Smart Retrofit Installation
Introduction The Solar Smart has a mounting bracket that allows the operator to rotate slightly to reduce wear and tear on the chain drive system for greater performance and reliability. Because of this
More informationInstructions on installing the R/R to the front battery cover.
April, 2008 Instructions on installing the R/R to the front battery cover. Please read all of the steps so you will be familiar with the complete relocation installation first. The purpose of this relocation
More informationTurn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles
Turn Signal Kit Installation Instructions for Model A Fords & Other Antique Vehicles Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0005N Thank you for purchasing
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More information* Caution : Brushes are brittle. Do not brake them. 3UE
The IVOPROP operates on a COMPLETELY UNIQUE adjustable pitch system that allows for substantially less hardware and rotating mass than any other ground pitch adjustable prop. The unique pitch adjustment
More informationYour Legal Fuel Tank Source.
February 23, 2015 IS# 808 Page 1 of 13 THANK YOU FOR PURCHASING A TRANSFER FLOW 40 GALLON TOOLBOX REFUELING SYSTEM. PLEASE READ THE FOLLOWING PROCEDURES CAREFULLY BEFORE STARTING THE INSTALLATION. CAUTION:
More information2016 Wand Handle Repair Instructions & Parts List
2016 Wand Handle Repair Instructions & Parts List Updated 9/11/18 2018 by Crafco, Inc. All Rights Reserved 2016 New Style Wand Assembly - Part Number 52200 This style wand assembly is field serviceable.
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT 2013+ FORD FOCUS ECOBOOST Document: 19-0168 Support: info@radiumauto.com Working under the vehicle is required. This installation is best performed with the
More informationINSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT
INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT BMW E46 3-Series, Excl Convertible Document: 19-0056 Support: info@radiumauto.com Relieve fuel pressure in vehicle before beginingthe installation. Disconnect
More informationInstallation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output)
Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output) PN L300080607 Revision - 1.1 Lingenfelter Performance Engineering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationA. Preparing the charge harness. Start by removing the plastic covers by the battery terminal.
twist battery relocate kit and harness. Step 1 A. Remove battery. Start by removing the negative battery cable and then the positive. After removing the battery cables remove the battery hold down bracket.
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More informationInstallation or Inspection Checklist
Sequencing Batch Reactor Installation or Inspection Checklist Only modules bearing the NSF logo and designated PS1-XX are certified to NSF/ANSI Standards 40 and 245 2018 Anua 1-2018 Pre-installation and
More informationOPT7 LED AURA UNDERBODY KIT GENERAL INSTALLATION GUIDE
1 x LED Control Box 2 x 48 OPT7 LED Bars with Smart-Color LEDs 2 x 36 OPT7 LED Bars with Smart-Color LEDs 1 x E-Z Remote (Batteries Included) 1 x E-Z Keychain Remote (Batteries Included) 4 x 10ft LED Strip
More informationInstallation of Halo CCFL Rings edited by
Installation of Halo CCFL Rings edited by www.motorcyclehidlights.com Please use the below installation as an example for your project. Installation is done on a CBR600 however the same procedure will
More informationToyota Prius Hybrid Aftermarket Double DIN Stereo Installation Manual
2004-2009 Toyota Prius Hybrid Aftermarket Double DIN Stereo Installation Manual CRUZ INC P a g e 1 2004-2009 Toyota Prius Hybrid with JBL Amplified Sound System and Navigation Installation Manual For this
More informationZip Tie Domes. 2 Frequency Geodesic Silo Dome Assembly Manual. Silo Dome Version
Zip Tie Domes 2 Frequency Geodesic Silo Dome Assembly Manual Silo Dome Version (c) 2015 Zip Tie Domes 1857 Brindley Hollow Rd Buffalo Valley, TN 38548 (931) 858-6892 Zip Tie Domes - 2V Silo Dome Manual
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring
More informationSection 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A
RotorWay International Page A Tail Rotor Drive Procedures covered in this section: Install driveshafts and gearboxes; install drive belt and tensioner; fabricate and install tail rotor pitch actuator arms;
More informationPrusa i3 Printer Assembly Guide
Prusa i3 Printer Assembly Guide Special thanks to Carlos Sanchez and Miguel Sanchez for the graphics. All graphics captured from their great animation: http://www.carlos-sanchez.com/ Prusa3/ For copyright
More informationCross Hare Installation Guide
Cross Hare Installation Guide Introduction: The Cross Hare is designed to provide all of the functions you need to control a one or two track grade crossing in a prototypical manner. The Cross Hare uses
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationPart# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)
Part# 18-1819 JL AIR IT UP 4 Tire On Board Air Delivery System (Requires External Air Source) The most up-to-date instructions always visit www.updownair.com www.updownair.com 833-226-4863 I M P O R T
More informationModel A Turn Signal Kit Installation Guide
Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.
More informationJBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions
JBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions Description The JBS-100-STB is a NEMA 4X rated power connection kit. It is designed for use with Raychem BTV-CR, BTV-CT,
More informationThese instructions show how to build the Remote Controlled Fart machine Sound Kit.
Remote Controlled Fart Machine Assembly Instructions These instructions show how to build the Remote Controlled Fart machine Sound Kit. Tools Required Drill with 7/64, 3/16, and ¼ drill bits. Holt melt
More informationELECTRICAL SYSTEM UPGRADE
NEW CONTROLLER & ELECTRICAL SYSTEM UPGRADE FOR DAIRY TECH, INCORPORATED 10, 30 & 60G PASTEURIZERS Parts to Include 2 Wire ties (Nuts) 2 sticky wire mount pads Large Rubber Grommet (for bottom of electric
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More informationRace Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE
Race Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE PARTS LIST (INCLUDED IN THE KIT) 1 x LED Control Center Box 2 x 48 RGB Aluminum Channel LED Bars 2 x 36 RGB Aluminum Channel LED Bars 1 x
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More informationToyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52120 to complete the installation
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationSafe-T-element Installation Instructions
Safe-T-element Installation Instructions For: PTI STEZA (2x2 Burner Configuration) & PTI STEZB (3x1 Burner Configuration) Revision K (May. 3 2012) TABLE OF CONTENTS 1. PREPARATION... 3 1.1 General Safety
More informationLionel ElectroCoupler Upgrade Kit Instruction Manual /04
Lionel ElectroCoupler Upgrade Kit Instruction Manual 72-4141-250 1/04 Congratulations! Congratulations on your purchase of the Lionel ElectroCoupler Upgrade Kit! These couplers are activated by commands
More informationAssault Air Bike Assembly Instructions
Assault Air Bike Assembly Instructions Tools Needed: Box Cutter 6mm Hex Wrench Phillips Screw Driver 13mm Wrench 22mm Wrench 15mm Wrench Step 1: Lay the Assault Airbike Bike box on the ground. Step 3:
More informationRevision Date: Building a dual pump system for an open boat. Description:
Disclaimer: The information is provided as-is. The author(s) accepts no liability for the accuracy, availability, suitability, reliability and usability. The following information is in the public domain
More informationYOU MUST WEAR SAFETY GLASSES DURING EACH STEP OF THESE INSTRUCTIONS
Machine Racer: Rally Preparation 1. Print the Working Drawing of the design you created and simulated in the Mousetrap Car 2.0 STEM Application. You can find your Working Drawing in the "Outputs" tab of
More informationG&G GR14 Airsoft Reassembly
G&G GR14 Airsoft Reassembly This Guide will show you the right technique for proper and fast assembly. Written By: 101 Tech USA ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION The G&G m-14
More informationWinch Operation Check
Winch Operation Check Description Winch Operation should be checked as part of the A Service. Winch Operation should also be checked before using the Winch. Tools and Supplies Winch Controller Wood Block
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationCabling Instructions NOνA Project Written By: Dale Mudd September 21 st, 2010
Cabling Instructions NOνA Project Written By: Dale Mudd September 21 st, 2010 P#= Part Number NOTE: Specific crimp tools located at end FEB/TEC Lower Voltage Cables Bottom of SB120 to Bottom of 60A Breaker:
More informationMARCH TECH TIP Common Repairs for the ZW Transformer Part 1 By Jim Weatherford
MARCH TECH TIP Common Repairs for the ZW Transformer Part 1 By Jim Weatherford The most popular transformer built by Lionel, by far, is the 275 watt ZW. It provides a combination of power, flexibility,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationIMPORTANT. Tools Needed: (depending upon vehicle) Phillips Screwdriver. Drill & Bit Set. Wire Stripper/ Crimp Tool
Revision 3/14/05 Amplifier Installation Guide IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call:
More informationBachmann Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann 2-6-6-2 Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital
More information20 Rigid Industries LED Light Bar Installation into a 2002 Ford Super Duty
20 Rigid Industries LED Light Bar Installation into a 2002 Ford Super Duty This write-up is how I installed the Rigid Industries 20" E-Series LED Light Bar into the grill area behind the license plate
More information(31 ) ZEON CONTROL PACK RELOCATION KIT
Warn Industries, Inc. 12900 S.E. Capps Road Clackamas, OR USA 97015-8903 1-503-722-1200 FAX: 1-503-722-3000 www.warn.com Customer Service / Service Clients: 1-800-543-9276 International Sales Support /
More informationDL650 Odyssey Luggage Installation Guide
DL650 Odyssey Luggage Installation Guide Thank you for purchasing Jesse Luggage for your Motorcycle. Our Luggage, handcrafted in the USA, is designed for those with an interest in finding the most durable
More informationPRODUCT SAFETY NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationP4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION
P4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION TOOLS REQUIRED 2, 2.5, 3, 5 mm allen keys 8, 9 mm open faced cone wrench Pliers Cable cutters Torque wrench MATERIALS REQUIRED: 1 x P4 chainstay
More information