YOU MUST WEAR SAFETY GLASSES DURING EACH STEP OF THESE INSTRUCTIONS
|
|
- Letitia Hubbard
- 6 years ago
- Views:
Transcription
1 Machine Racer: Rally Preparation 1. Print the Working Drawing of the design you created and simulated in the Mousetrap Car 2.0 STEM Application. You can find your Working Drawing in the "Outputs" tab of the Mousetrap Car 2.0 STEM Application. 2. Gather materials and tools for fabricating your Machine Car design. Materials Balsa Blanks: 2 side rails (plus 1 extra) 1-Mousetrap 1-1/8" Aluminum Rod (Axle Material) 1-3/16" X 8" Aluminum Tube (Lever Arm) 1-30" String 2-Rear Wheels 2-Front Wheels 2-Rubber Bands (Rear Wheel Traction) 4-Brass Washers 1-Plastic Bushing (Straw) 1-Wire for Axle Hook 3-Spools Nylon Screw/Washer/Bolt for Steering Arm Wood Glue Hot Glue (Low Temp. Preferred) Tools Safety Glasses Hobby Saw Hobby Knife Cutting Board Drill Press Tube Cutter Diagonal Cutter Pliers Needle Nose Pliers Wood Clamps Spring Clamp Ruler Materials and Tools YOU MUST WEAR SAFETY GLASSES DURING EACH STEP OF THESE INSTRUCTIONS
2 Frame Fabrication (without Pre-Drilled Rails) 1. Carefully review your Working Drawing. It contains all the measurements you will need to layout your parts for fabrication. 2. Working from your drawing, layout the length of the side rails and hole location. Hole Location 3. Using a hobby saw, place the parts on a cutting surface and cut to the specified length. Cut to Length 4. Drill the axle holes on a drill press (or you can use a hand drill) using a 11/64" bit. A 11/64" bit will work with the straw bearing provided in the WhiteBox Learning kit. If you plan to use another type of bearing, check for the correct size hole for bearing fit before drilling. Drill Axle Holes 5. Unless you are using the steering arm option, you should now have two frame rails with an equal wheelbase for axles. Frame Rails
3 Steering Arm (Optional) 1. Cut the front end of one Rail 35mm shorter than the designed dimension to accommodate the length of the Steering Arm. 2. Measure the center 10mm from the front of the Rail and drill a 11/64" hole for the machine screw. 3. Cut a steering arm to a length of 55mm and a spacer to a length of 25mm, both from either the excess wood from your rails, or from the extra rail piece included in your kit. Glue the spacer to the end of the steering arm. 4. Measure the distance from the front of the other Rail (the one not being used for steering) to the center of its axle hole. Use this measurement to layout the axle hole on the Steering Arm. Drill a 11/64" hole in the Steering Arm for the axle and bearing. 5. Measure the center 15mm from the back of the Steering Arm and drill a 11/64" hole and cut the slot with a hobby knife. Use a straight edge (ruler) for an accurate cut. Steering Arm Preparation 6. Assemble the steering arm to the side rail using the machine screw, nut and washer (included in your kit). Hand tighten for now. Steering Arm Assembly
4 Mouse Trap Preparation 1. The stock mousetrap that provides the propulsion force needs to be modified. Look over the image at the right. There are several parts that need to be cut and discarded. The procedure to follow is to start at step #1 and work clockwise through #2, #3 and #4. (See picture for more detail). Modify Mouse Trap 2. Use diagonal cutters to snip the parts in the areas specified in #1 above. Be sure you are wearing your safety glasses. Snip Mousetrap Arm 3. Follow through with steps #2, #3 and #4 to prepare the spring mechanism. Hold on to the part removed in step #4. It can be used for the lever arm hook. Prepare Spring Mechanism Modification Option 1. After following the steps in "Mouse Trap Preparation", the mouse trap hammer arm is now ready for the lever arm. However, after you cut your axles, you might have additional material to work with. If so, as a modification option, cut a section of the 1/8" aluminum rod (also axle material) to approximately 100mm. Measure 50mm, clamp with pliers and bend to just over 90 degrees. The lever arm needs to align with the axle hook so the angle may need to be adjusted during final assembly. Bend Hammer
5 2. Using diagonal cutter pliers, cut the trap's hammer to prepare for removal. Cut Hammer 3. Carefully apply pressure to the spring to hold it in place. Remove the stock hammer and replace it with your fabricated aluminum hammer. Insert Custom Hammer 4. Your modified mouse trap is now the power plant for your vehicle. Replacing the original hammer with your aluminum hammer has several advantages. Lower friction coefficient. The friction coefficient for steel to steel is 0.8. For aluminum and steel it is Reduced mass for aluminum hammer and lever arm assembly. The mousetrap is the engine. If you improve the power plant, you improve performance. And... Completed Hammer 5. If you want, you can be creative and experiment with innovative engineering design solutions that can improve your design. In this case, the hammer is designed to align the lever arm with the center of the axle. Customize Hammer
6 Frame Assembly 1. Precisely measure the points where the rail will be attached to the bottom of the mousetrap. The axle holes must be aligned so that they are across from each other. Precision is important. The axle, when assembled, must be perpendicular to the rail or your car will not run straight. Rail Alignment 2. Glue and clamp the rails in position with wood glue. Attach Rails 3. Cut the bearings to a length so they cover the wood surface. Assemble the bearings (straw) in the holes of the rails. If the bearings fit too loosely in the hole, tack them in place with hot glue. Bearing Assembly
7 Lever Arm Mechanism 1. Using a tube cutter, cut the lever arm to your specified length. Your working drawing will have the exact dimensions. Note: Tube cutters work by tightening the cutter against the tube and rotating it until it turns freely. Tighten again and rotate. Repeat until the tube is cut. Cut Lever Arm 2. Cut off the bend of the hammer latch so the remaining shaft is straight. Cut Off Bend 3. Insert the hammer latch piece (the "string hook") that you cut in step #2 above (or alternatively use a screw eye) into the tube. Using pliers, crimp the end of the tube around the string hook to secure it in place. Crimp String Hook to Tube 4. Follow the same procedure to form the tube around the string hook along the length of the threads. Aluminum is a pliable material that is easy to form. Form Tube to String Hook 5. Cut the string about 3" longer than your specified length. Tie a loop on one end of the string. 6. Measure the designed length of the string from the loop's end to the lever arm tying point, and tie the other end to the string hook. The total length after assembly should be the designed length specified in your working drawing. Tie String to Lever Arm Hook
8 7. Assemble the lever arm to the hammer. Assemble Lever Arm 8. Using needle nose pliers, set the spring tension arm on top of the hammer and lever arm assembly. Note: If the spring arm does not seat properly, crimp the lever arm to provide a flat surface to seat the spring arm. Assemble Lever Arm 9. Your power plant is now ready. Potential energy will now be converted to kinetic energy. Power Assembly
9 Wheel and Axle 1. Inspect your wheels for excess material or tabs. Remove any imperfections with a hobby knife and/or sand paper. Inspect Wheels 2. Place the rubber bands around the rear wheels. The rubber "tire" provides the friction (traction) needed to prevent wheel slippage. Attach Rubber Bands 3. Refer to your working drawing and layout the length of the axle on the aluminum axle rod. Cut the aluminum axles to length using diagonal cutters. Cut Aluminium Axles 4. Thread the axle through the bushings. If a spool was used in your design, seat the spool on the axle during assembly. Position the spool so it aligns with the lever arm when in power position. 5. For the axle "hook", start by wrapping the wire around the axle three (3) turns. Spool Placement 6. Twist the wire to form the axle hook. Cut the wire tie leaving approximately 1/8" for the hook. If a spool is used, slide the hook so it rests against the spool's surface.
10 Twist Wire 7. Tack all the components (spool and axle hook) in place with hot glue to prevent power loss from spinning. (You also may want to add glue to the axle before placing the spool, in order to secure it in place). Tack Components 8. Slide the brass washers on the axles, then add your wheels to the axles. The brass thrust washer provides a bearing surface if/when the axle moves side to side Attach Wheels 9. Assemble the wheels on the axles. The axles are supposed to fit snugly in the axle holes. So you may want to bore out the axle holes with a 1/8" drill bit, before inserting the axles into the wheels. And/or, it may also be necessary to tap them into place. Secure Wheels 10. When assembled, there should be approximately 2mm clearance between the axle assembly and the frame. The thrust washers will provide a bearing surface when the wheels move side to side. Verify Axle Clearance 11. You now have a completed Machine Racer ready for testing!
11 Completed Machine Racer
12 Roll Test (Steering Arm Option) 1. Roll test the vehicle to determine if adjustments need to be made. In this case, the masking tape on the floor indicates straight travel. Align the vehicle parallel to the line and give it a push. If it deviates from the line, adjustments need to be made. 2. If the steering arm is adjusted forward, the vehicle will turn left; adjust backward, the vehicle will turn right. Given the results of your roll test, make the necessary adjustments and test again. Repeat until your vehicle travels straight. Now you're ready to race... Good Luck! Steering Adjustment
Magnetic MTV Kit. User Guide. Components
Magnetic MTV Kit User Guide Components The Magnetic MTV Kit should contain the following items. If anything is missing, call Customer Service at 800-358-4983. Two 3" x 18" sheets of 1/4" balsa wood Mousetrap
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More information1:6 BLACK BRANT II. c o s m o d r o m e r o c k e t r y
c o s m o d r o m e r o c k e t r y 1:6 BLACK BRANT II This kit is capable of use with high thrust motors. It is therefore strongly recommended that epoxy be used throughout the construction of this kit.
More informationP4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION
P4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION TOOLS REQUIRED 2, 2.5, 3, 5 mm allen keys 8, 9 mm open faced cone wrench Pliers Cable cutters Torque wrench MATERIALS REQUIRED: 1 x P4 chainstay
More informationEXTRA 330LX. Specifications: Code: SEA274. Graphics and specifications may change without notice. ASSEMBLY MANUAL
ASSEMBLY MANUAL EXTRA 330LX Code: SEA274 Graphics and specifications may change without notice. Specifications: Wingspan---------------82.0 in (208.2 cm). Wing area---------------1349.4 sq.in ( 87.1 sq.dm).
More informationJ & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034
J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The Hyperdrive Assault has gone through months
More informationTrainer Assembly Manual
Trainer Assembly Manual www.pilot-rc.com -Pilot Trainer- 1 -Pilot Trainer- 2 -Pilot Trainer- 3 -Preliminary i wing & stab assembly- 1-) Locate both Plywood wing joiners (Large and small one) 2-) Insert
More informationInstruction Manual. Wingspan : 1400 mm (55.12 inch) : 1480 mm (58.27 inch) : 5500gr gr. : 6-9 channel/ 8 servo high torque,1 standard
Wingspan : 1400 mm (55.12 inch) g Length : 1480 mm (58.27 inch) Weight : 5500gr - 6000gr Radio : 6-9 channel/ 8 servo high torque,1 standard Engine : GT 22 OS KIT CONTENTS: We have organized the parts
More information: 6 channel - 9 servo
g Wingspan : 2005mm (78.94 inches) Length : 1640mm (64.57 inches) Weight : 6400g - 6600g Engine : 25cc - 35cc Radio : 6 channel - 9 servo KIT CONTENTS: We have organized the parts as they come out of
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum
More informationShown with optional GFR-1017R Body Posts. J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN
Shown with optional GFR-1017R Body Posts J & D Machine / Hyperdrive / MSA 3711 Moon Bend Rd. Chapel Hill, TN 37034 www.hyperdriveracing.com 1 You now own a state of the art 1/10 scale oval race car. The
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2190mm (86.2 in) - Length: 1907mm (75 in) - Flying weight: 9000-12000 gr - Wing area: 92 dm2 - Wing loading: 98g/dm2 - Wing type: Naca airfoils - Retract gear type: Air-retract
More informationInstruction Manual. Wingspan : 2270mm (89.37 inches) : 1870mm (73.62 inches) : 7400gr gr. : 4 channel - 6 standard servo.
Wingspan : 2270mm (89.37 inches) g Length : 1870mm (73.62 inches) Weight : 7400gr - 7600gr Radio : 4 channel - 6 standard servo Engine : 25cc-35cc KIT CONTENTS: We have organized the parts as they come
More informationThis LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506.
L.E.D. INSTRUCTIONS I D T S O T U B I R M O C R Y N A P Kit contains: This LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506. For the power supply: 1-LED power supply circuit board, 2
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationThe Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationSkyline 4 Fascia Fabrication & Installation Instructions
Components Needed Page 2 Tools Needed Page 2 System Diagram Page 3 Instructions Step 1: Install Brackets Page 4 Step 2: Install Pre-assembled Shade Page 4 Step 3: Install Fascia Clip Page 4 Step 4: Cut
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationNational Science Bowl Teacher Workshop 2013
National Science Bowl Teacher Workshop 2013 2 2013 National Science Bowl Middle School Car Competition Introduction One of the Department of Energy s (DOE) national clean energy goals is to put one million
More informationLuminator Low-Rise Headlight. Designed and built by Radioflyer Innovations
Luminator Low-Rise Headlight system for C5 Corvette Designed and built by Radioflyer Innovations 1 Tools Required Phillips head screwdriver Flathead screwdriver Torx 15 screwdriver Torx 20 screwdriver
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More information: 7 channel - 9 servo, Hi-Torque ( Minimum 6 kg ).
g Wingspan : 1820mm (71.65 inches) Length : 1625mm (63.98 inches) Weight : 6900gr Engine : 25cc - 35cc Radio : 7 channel - 9 servo, Hi-Torque ( Minimum 6 kg ). KIT CONTENTS: We have organized the parts
More informationSunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais
SunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais Contents of Kit: A. 3 1/16 x1 x11 basswood rotors B. 3 1/16 x2 x2 basswood fins C. 3 1/16 x5/16 x1/2 basswood hold spacer D. 3
More informationTop Down Rollstar Shade Installation Instructions
Top Down Rollstar Shade Installation Instructions Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the dimensions you specified. With proper
More informationRevised 10/23/2015 Page 2 of 10
1.Remove the gauge, side panels, hood and headlight. Remove the air box from the throttle bodies then remove the seat and gas tank. 2.Carefully remove temp sensor from air box using a small pick or screw
More informationNext, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.
Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More informationFigure 1. A CheapBot Robot
A CheapBot controller needs a robot body to function. An ideal robot body for the beginner consists of two sheets of Syntra plastic, separated by four bolts. The bottom deck contains the robot controller
More informationCommander SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 - FRONT UPPER A-ARMS 2 - FRONT LOWER A-ARMS 4 - COTTER PINS 2-12MM JAM NUTS 2 - TIE ROD EXTENDERS 8- FLANGED DELRON BUSHINGS 4- DELRON CASTER SPACERS 6 - GREASE FITTINGS 3 - BEARING REMOVAL
More informationBruce s Science workbench
Baby Vandegraff Generator by Bruce Yeany 2001 https://www.youtube.com/watch?v=parq01q DKe4 http://www.instructables.com/id/van-de- Graaff-Electrostatic-High-Voltage- Generator/ https://www.youtube.com/watch?v=esz
More informationSBACH SCALE 1:4 ½ ARF
SPECIFICATION - Wingspan: 1663mm (65.5 in) - Length: 1638mm (64.5 in) - Flying weight: 4700-5200 gr - Wing area: 56 dm2 - Wing loading: 85g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationSection 5: Parts Replacement
Section 5: Parts Replacement Should the STAR TRAC 4500 Treadmill experience a problem requiring replacement of a specific part, the following procedures will help and instruct in the replacement of major
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationI n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION
I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2
More informationMODEL 300 FLIP KIT - PARTS LIST
MODEL 300 FLIP KIT - PARTS LIST SHIFTER PLATE 1 EA REAR SHIFT RAIL 1 EA FRONT SHIFT RAIL 1 EA SHIFT RAIL COVER 1 EA SHIFTER ASSEMBLY 1 EA BRASS PIPE PLUGS 5 EA REAR OUTPUT SHIFT FORK 1 EA SHIFT FORK PADS
More informationRJS WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS
RJS2006 30 WB ELECTRIC T/F DRAGSTER KIT LESS ELECTRICS THANKS FOR BUYING THIS RJ SPEED DRAGSTER KIT. IT IS MADE FOR STRAIGHT LINE DRAG RACING AND MAY BE BROKEN IF RUN INTO SOLID OBJECTS REPEATEDLY AT HIGH
More informationRJS2017 SPORTSMAN RACER KIT LESS ELECTRICS
RJS2017 SPORTSMAN RACER KIT LESS ELECTRICS THANKS FOR BUYING THE RJ SPEED 1/10 SPORTSMAN RACER KIT FOR OVAL RACING, DRAG RACING OR JUST FUN STREET BASHING. THE ASSEMBLY WILL NOT BE DIFFICULT IF YOU READ
More informationKre 8. Solar Powered Racer V4d
Solar Powered Racer V4d (OR Battery Powered Car) 1 Solar (sun powered) Racer OR battery powered racer This electric powered racer can be powered using direct sunlight (using the solar panel) * OR a battery
More informationLIGHT DUTY ROLL UP DOOR
1-800-225-6729 LIGHT DUTY ROLL UP DOOR CAUTION Use proper lifting equipment and correct lifting procedures to avoid damage or injury. MODEL 150C installation guide A rolling door is a large heavy object
More informationTable of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03
Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator
More informationRS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.
RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch
More information1660mm (65.4 in) 1200mm (47.2 in) 2700gr gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke
Instruction Manual CESSNA-46 1660mm (65.4 in) 1200mm (47.2 in) 2700gr - 3000gr 6 channel - 7 servo standard 46/ 2 stroke or 52/ 4 stroke KIT CONTENTS: We have organized the parts as they come out of the
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE
TITAN pt. no.: 03 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE 30 Gallon* Spare Tire Auxiliary Fuel
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1410mm (55.5 in) - Length: 1278mm (50.3 in) - Flying weight: 3.2-3.4 kg - Wing area: 41.3 dm2 - Wing loading: 75g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationTSS Fit Kit Installation Instructions Timbersled Snow Bike System
TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2015 CR-Z Publications No. VERSION 1 Issue Date SEP 2014 PARTS LIST Armrest console Armrest bracket 2 Collars 4 Washer-bolts 2 Caps TOOLS AND SUPPLIES REQUIRED
More informationMS:183 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
MS:183 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------79.9in (203cm). Wing area -----------------1165.6sq.in (75.2sq dm).
More informationSIZE.120 OR 30CC SCALE 1:5 ARF
PC21 PILATUS MK2 SIZE.120 OR 30CC SCALE 1:5 ARF SPECIFICATION - Wingspan: 1772mm (69.72in) - Length: 2019mm (79.5 in) - Flying weight: 6.4-7.2 kg - Wing area: 57.6 dm2 - Wing loading: 113g/dm2 - Wing type:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TK6-100 Application 2013 FIT Publications No. AII 13198 Issue Date JULY 2012 PARTS LIST Ambient light kit 2 Ambient lights 6 Wire ties Fuse label 2 Grommets
More informationFabric Studio Custom Roll Shades Installation Instructions
Fabric Studio Custom Roll Shades Installation Instructions Cassette System Battery Motor Lifting System Inside or Outside Mount Thank you for purchasing your new roll shade. It has been custom-made from
More informationPARTS LIST: 8581 DODGE LONG ARM BRACKETS 03-13
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8580 03-12 DODGE 2500/3500 4X4, 06-08 1500 MEGACAB 4X4 LONG ARM SUSPENSION KIT V3.0 GENERAL NOTES: These instructions are also available
More informationMOUSETRAP VEHICLE 2012 CONSTRUCTION TIPS
MOUSETRAP VEHICLE 2012 CONSTRUCTION TIPS Bro. Nigel Pratt bronigel@kellenberg.org 1 Dennis Papesh dpapesh@holyangels.cc Many Thanks Thank you to Bobby B. of Magsig Middle School and Patrick B. of Holy
More informationInstruction Manual. Specification:
Instruction Manual L O W Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1790gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo W I N G KIT CONTENTS: We have
More informationthe leading edge of the wing, at the fuselage - Length: 1540mm (60.6 in) 10% expo; High: 15mm up/down, 10% expo - Wing area: 40dm2
SPECIFICATION - Gravity CG: 165-170 mm (6.5-6.7 in) Back from - Wingspan: 1400mm (55.1 in) the leading edge of the wing, at the fuselage - Length: 1540mm (60.6 in) - Control throw Ailerons: Low: 12mm up/down,
More informationInstruction Manual. Wingspan : 1400mm (55.12 in) : 1370mm (53.94 in) : 2600gr gr. : 4 channel / 5 servo. : / 2 stroke_52-71 / 4 stroke
Instruction Manual 540 Wingspan : 1400mm (55.12 in) g Length : 1370mm (53.94 in) Weight : 2600gr - 2800gr Radio : 4 channel / 5 servo Engine : 46-52 / 2 stroke_52-71 / 4 stroke KIT CONTENTS: We have organized
More informationI/C FLIGHT GUIDELINES
SPECIFICATION - Wingspan: 3500mm (137.8 in) - Length: 1650mm (64.96 in) - Flying weight: 3700-4000 gr - Wing area: 75 dm2 - Wing loading: 49g/dm2 - Wing type: HQ profile - Covering type: Genuine ORACOVER
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More information60-90 EXTRA 260/300 DLE 20 INSTALLATION GUIDE
60-90 EXTRA 260/300 DLE 20 INSTALLATION GUIDE This engine installation addendum will outline the installation of the new DLE 20cc in the 60-90 Extra 260 and Extra 300. The Extra 300 is shown however the
More informationTOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation
Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear
More informationFRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII 42587 Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170
More informationSECTION 35iS/U: LANDING GEAR & ENGINE MOUNT
WD-1221 ENGINE MOUNT STANDOFF SECTION 35iS/U: LANDING GEAR & ENGINE MOUNT U-01203E-1 INBOARD DOUBLER PLATE U-01203B-1 INBOARD WEAR PLATE U-01203C-1 BEARING PLATE U-01203-2 (U-01203-1 SHOWN) INBOARD MAIN
More informationStep #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good t
How to make a ROV! Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good to have extras. Using the wire cutter,
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 6000mm (236.2 in) - Length: 2873mm (113.1 in) - Flying weight: 14-18 kg - Wing area: 219.4 dm2 - Wing loading: 64g/dm2 - Wing type: HQ airfoils - Covering type: Genuine ORACOVER
More informationINSTALLATION GUIDE Canted Billet 4-Bar, 4x2 Rear Frame
INSTALLATION GUIDE 7154 Canted Billet 4-Bar, 4x2 Rear Frame Description: Non-application specific, weld-in, 4 x 2 rear frame for use with Chassisworks 6241 billet aluminum suspension links. IMPORTANT:
More informationAdult Car Plans. A comprehensive guide to help you build an official Soap Box Derby Adult Car
Adult Car Plans A comprehensive guide to help you build an official Soap Box Derby Adult Car 1 Table Of Contents Introduction...Page 3 Adult Car Floorboard...Page 4 Step One Steering Stop Installation...Page
More informationRIGGING THE FLIGHT CONTROLS
RIGGING THE FLIGHT CONTROLS Rigging refers to the installation and adjustment of the rods that move flight surfaces in response to inputs from the controls of the helicopter. These rods are cut to length,
More informationInstallation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN
More informationService Bulletin. HIITMill (X) Brake Lever Drift
HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This
More information96in Super Decathlon ARF
96in Super Decathlon ARF Instruction Manual Specifications Wingspan: 96in (2438mm) Length: 63.5 in (1614mm) Weight: Approx. 13lbs (6.5kg) 1 Dear Customer, Congratulations on your purchase of Super Decathlon
More information11 - Fairings. Fairings. February XLF Page 11-1
11 - Fairings Fairings February 2003 11-XLF Page 11-1 11 - Fairings This Page Intentionally Left Blank Page 11-2 11-XLF February 2003 11 - Fairings Contents 11.0 - Chapter Preface... 11-4 11.0.1 - Parts
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationChevrolet 3100 IFS Kit
1947-54 Chevrolet 3100 IFS Kit Congratulations on your purchase on what we believe is the finest IFS kit available for 1947-54 Chevrolet pickups with stock frames. We have invested many hours into designing
More informationto fly. Most hardware included and all replacement parts are available.
Instruction Manual The Thunderbolt P47 was perhaps the greatest of world war II in terms of all round performance and capability Phoenix Model has recreated a 2C - 60 class engine (or 4c 91 class) It was
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2008 ACCORD 2 AND 4-DOOR Publications No. AII 38281 Issue Date NOV 2007 PARTS LIST Attachment Kit P/N 08E02-TA0-100 trim retainer
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationInstallation Instructions Sport Shifter
The B&M Sport Shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. It is equipped with neutral safety and backup light switches, transmission brackets
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE
TITAN pt. no.: 02 0000 0180 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE 30 Gallon* Spare Tire Auxiliary Fuel
More informationAIRCRAFT LANDING GEAR CONSTRUCTION MANUAL
APPENDIX AI KITPLANES FOR AFRICA AIRCRAFT LANDING GEAR CONSTRUCTION MANUAL Revision: C September 2008 Page L1 of 20 NOTE: Please read the General Manual before proceeding. Please read through the entire
More informationOVER THE KNUCKLE 1-TON STEERING INSTALLATION INSTRUCTIONS
OVER THE KNUCKLE 1-TON STEERING INSTALLATION INSTRUCTIONS TOOLS NEEDED Grinder with cutoff wheel, sawzall, cutting torches, or a plasma cutter Welder (for optional sway bar mounts) Hand drill with a ½
More informationFLYING MODEL ROCKET KIT INSTRUCTIONS KEEP FOR FUTURE REFERENCE. TEST-FIT ALL PARTS TOGETHER BEFORE APPLYING ANY GLUE!
www.estesrockets.com ESTES INDUSTRIES 1295 H Street Penrose, CO 81240 PRINTED IN CHINA EST 1247/2053 FLYING MODEL ROCKET KIT INSTRUCTIONS KEEP FOR FUTURE REFERENCE. ASSEMBLY TIP: Read all instructions
More information8mm EPP Acrocub. Instruction Manual. Specifications
8mm EPP Acrocub Instruction Manual Specifications Wingspan: 34.6 in (880mm) Length: 31.5 in (800mm) Wing Area: 213.9 sq in (13.8sq dm) Flying Weight: Approx. 9oz (270g) Dear Customer, www.valuehobby.com/8mm-epp-acrocub.html
More informationMS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:159 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------61.8in (157cm). Wing area -----------------1100.5sq.in (71.0sq dm). Weight
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK (WITH MOON) Application 2009 PILOT Publications No. AII 39492 Issue Date MAY 2008 PARTS LIST HFL Attachment Kit 2 Washer screws, 4 x 12 mm HFL
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2567mm (101in) - Length: 2190mm (86.2 in) - Flying weight: 11-13 kg - Wing area: 101 dm2 - Wing loading: 99g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER -
More informationComfort Tri-Rider Assembly Guide
1. Carefully remove all the components and packaged hardware from the shipping boxes. 2. Remove all protective materials from the fork, front frame and rear frame sections. 3. Read this assembly manual
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More informationThis is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the
This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the box and assemble it. If you have not assembled a bicycle
More informationInstallation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:
Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima
More informationInstruction Manual. Wingspan : 1694mm (66.69 in) : 1470mm (57.87 in) : 3200gr gr. : 61 two stroke/ 71 four stroke. : 6 channel / 7 servo
Wingspan : 1694mm (66.69 in) g Length : 1470mm (57.87 in) Weight : 3200gr - 3800gr Engine : 61 two stroke/ 71 four stroke Radio : 6 channel / 7 servo KIT CONTENTS: We have organized the parts as they
More informationInstruction Manual. Wingspan : 1884 mm (74.17 in) Length. Weight. Engine. : 4 channels / 5 servo standard. : 1450 mm (57.
Wingspan : 1884 mm (74.17 in) Length : 1450 mm (57.09 in) Weight : 4000 gr Engine : 60 two strokes Radio : 4 channels / 5 servo standard KIT CONTENTS: We have organized the parts as they come out of the
More informationINTELLIQUILTER INSTALLATION ON GAMMILL MACHINES VERSION
INTELLIQUILTER INSTALLATION ON GAMMILL MACHINES VERSION 11.10.13 1. COMPUTER BRACKET From the left side of the head (viewed from the front) remove the three screws circled on Fig 1. Fig. 1 Remove the tablet
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory USB ADAPTER Application 2014 INSIGHT Publications No. AII 50655 Issue Date OCT 2013 PARTS LIST USB Adapter Attachment Kit P/N 08B28-TM8-100A 6 mm Flange nut Control
More informationINSTALLATION INSTRUCTIONS Accessory P/N 08L96-SZA-100A Application 2015 PILOT Publications No. AII 51544 Issue Date MAY 2014 PARTS LIST Advanced cargo net 2 Anchors A (Large) 4 Anchors B 6 Self-tapping
More informationStirling Engine. What to Learn: A Stirling engine shows us how energy is converted and used to do work for us. Materials
Stirling Engine Overview: The Stirling heat engine is very different from the engine in your car. When Robert Stirling invented the first Stirling engine in 1816, he thought it would be much more efficient
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationInstallation Instructions StarShifter
Installation Instructions StarShifter Part Number 80675 2000 by B&M Racing & Performance Products LLC The B&M StarShifter can be used in vehicles equipped with most popular three speed automatic transmissions.
More informationThe Magazine For Slot Car Enthusiasts
The Magazine For Slot Car Enthusiasts Building the Tomy Super G+ By Milt Surratt Tomy Super G+ slot cars have been around in the current form for about 12 years. Out of the package, the Tomy HO slot car
More information