Kodak 750H Carousel Projector Repair
|
|
- Piers James
- 6 years ago
- Views:
Transcription
1 Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors in this series, is that Kodak used plastics in them that deteriorate with time. It literally becomes brittle and crumbles. This plastic is used on the end of a solenoid plunger that increments and decrements the slide tray. It s also used in a set of gears in the remote focusing system. Kits can be purchased to replace these parts but there is a dearth of how to information, hence this article. All of the screws are either P-2 phillips or 1/4" hex. A magnetic pickup tool comes in very handy. Here are the tools I used:
2 Left to right. Exato knife, magnetic pickup stick, long & short 1/4" nut drivers, tweezers, 1/4" wrench, flat bladed screwdriver, #2 phillips screwdriver, a wire brush on top and an old towel to place the projector on. Place the projector upside down on the towel and open all the covers as shown below. Remove the projection lens from the front and the lens, heat absorber and 300W bulb, shown in yellow and put them in a safe place, though this is not necessary for the. Adjust the forward foot, shown in purple, so that it s all the way down and remove the rubber foot. Remove the four phillips screws in the corners, shown in red.
3 Remove the bottom cover by lifting and pushing slightly forward to clear the front foot height-adjusting knob and set it aside. What you have now should look something the picture below. Be aware that Kodak changed the design slightly over time. The unit shown here is an older design with a power cord that plugs into the back of the machine. I have a newer 750H, which I have also made the same repair to, that has the power cord hard-wired into the unit and uses the motor winding as a transformer. The procedure is pretty much the same for both units and I will point out deviations as we get into it. Here I point out the location of the focus gears and the solenoid, which is hidden under some sheet metal. Start off by removing the twisty tie. Then remove the five 1/4" screws shown below. (All four of the machine screws are of the same length.) And remove the now loose plate and set it aside. EDIT: Well, screw #3 may not need to be removed after all. NOTE: Newer models will have the power cord attached to this plate.
4 You ll notice that my machine has seen better days, lots of oxidation, dirt and peeling paint. When I got it the motor was seized from rust between the spiny and non-spiny parts. I removed it, took it apart, cleaned off the rust, lubricated and reassembled it. It spins again! Next we ll remove the focus drive motor. Aren t you excited! Remove the three screws shown in red below. These are special shoulder screws with a sheet metal thread. Don t confuse them with the two solenoid screws the look almost the same except they have machine screw threads! Remove the motor and set it out of the way with the wires attached. This is a good time to lubricate the shaft at the bearing points with some electric motor oil. In my case I also connected the motor to a power supply and made sure it would run, which it did after a little persuasion.
5 Remove the solenoid screws shown in yellow above and in red below. I recommend removing them in the number order shown below so that the plate remains attached until the solenoid screws have been removed. Remember not to mix up the solenoid and motor mounting screws. NOTE: Newer models will have more wires in this area and sheet metal screw #3 might be a machine screw. Once reassembled, screw #3 can be loosened so the solenoid plate can be slid up and down with the aid of a flat blade screwdriver to adjust for maximum plunger travel when pushing the reverse button. This page will be referenced again later!
6 Next, follow the orange and blue solenoid wires to the wire nuts that secure them. Remove the wire nuts and extract the solenoid wires, being careful to put the wire nut back on the mostly orange bundle of wires so they stay together and don t get lost. NOTE: On the newer models, as shown in the picture below, the blue wire will be soldered to a lug on the motor. Unsolder this wire from the lug. Alternatively you could cut the blue wire and use a wire nut, etc. to reattach it upon reassembly.
7 It will be a little fussy to get it out, but now carefully remove the plate the solenoid was mounted to and the solenoid itself. The solenoid plunger might stay behind but it can be fished out. Notice that the end of the solenoid mounting plate is slightly bent where screw #3 secured it. This bend should be away from the sheet metal it was mounted to upon reassembly. The solenoid plunger will look like the one in the picture below. Remove the rivet and replace the broken actuator with your new one. It may be a tight fit but it ll go in. It s softish plastic to be careful not to damage it with sharp tools.
8 I used a center punch to splay the hollow end of the rivet as shown below. Tada! That bit of broken plastic is why your projector would no longer show slides when pushing the forward and reverse buttons. Now it s time to reassemble what you took apart. The bit of new plastic on the end of the plunger is flexible so it can be squeezed into the slot shown below. Slide the plunger back into the solenoid and position the assembly as shown below. Route the solenoid wires back through the hole they passed through before you took it out. Yeah, refer to the pictures above if you don t remember. Using a dull tool, one with no sharp edges that will cut or nick the plastic, and work the plastic end into the slot until the two cutouts engage with the sides of the slot. Again, do this with a plunger in the solenoid coil. Yes, more fussy work. I found it easier to engage one notch and then work the other in with a long, slender tool. And the fussiness continues! Work the solenoid plate back into its original location, making sure the piece at the end where screw #3 goes in is bent away from the sheet metal as previously mentioned. Secure the coil to the plate with the two shoulder screws with machine screw threads. Yes, not easy.
9 Secure the plate to the sheet metal with the third screw. At this point, replace the focus gears. Remove the old gears and clean the remaining plastic from the shafts and press on the new gears as shown below. I used large channel - lock pliers to gently push the gears on. Note: I used a #9 (0.196 ) drill bit to clean the flashing out of the hole through the larger gear and a #45 (0.082 ) drill bit to clean out the hole in the smaller worm gear before pushing them on. Reversing the disassembly procedure, reinstall the motor. Continue reassembly and reattach the solenoid wires being sure to route them as they were originally. Reinstall the plate and the twisty tie/ties as they were. At this point I suggest flipping the machine right side up and plugging it in to make sure everything works. Be careful not to zap yourself on exposed wiring!! You should now adjust the position of the solenoid, as previously mention, so that when the rearward slide advance button (reverse slide) is pushed that the solenoid doesn t buzz yet has maximum travel, with a satisfying clunk, as mentioned previously.
10 Finally, put the bottom back on, making sure to put the machine screw in the location as shown in the beginning. Clean and reinstall the optics and bulb, if you removed them. Now enjoy your working once again projector! At least my basket case projector works well and I hope yours does too.
DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationwww.odometergears.com Mercedes-Benz Mechanical Odometer Repair This how to can be used for all mechanical repairs as the only difference will be the removal of the instrument cluster. http://www.dieselgiant.com/repairyourodometer.htm
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationNissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
More informationPT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner).
PT 709 firing pin and extractor removal. Disclaimer: My Taurus manual says not to take this apart (just flush it with cleaner). But several list members have done this without ill effect. So here goes:
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationLJ20 Distributor - Disassembly Inspection Repair
LJ20 Distributor - Disassembly Inspection Repair Old Codger New To Old Suzuki Jeeps The odometer on this 1972 LJ20 indicated the distributor had less than 10,000 miles of wear but during that time it had
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationVolvo 850 Radiator Replacement Jason Reed 29 March 2013
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationFord Ranger and Mazda Pickup Odometer Worm Gear Replacement
www.odometergears.com Ford Ranger and Mazda Pickup Odometer Worm Gear Replacement http://www.therangerstation.com/magazine/fall2008/odometer_worm_gear.htm ****************************************************************************************************
More informationLast Revision: 30JN THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 30JN2007 1969 THRU 1979 C3 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationGENESIS KIT for Rowe. INSTALLATION: BC12R, 1400 Special tools needed drill and a 5/32 bit
Page 1 of 5 GENESIS KIT for Rowe INSTALLATION: BC12R, 1400 Special tools needed drill and a 5/32 bit THE COIN DETECTOR LIGHT(S) ON THE COIN DISPENSER FRAME NEED TO BE THE NEWER RED LED TYPE. IF YOU HAVE
More informationLEGO Ferrari F40 (10248) Lighting Kit Installation Instructions
LEGO Ferrari F40 (10248) Lighting Kit Installation Instructions This guide walks you through the steps to install the Brickstuff lighting kit for the LEGO Ferrari F40 (LEGO set #10248). Written By: Rob
More information05/06 Gsxr 1000 Clutch Mod
By: Ali (Jetspeedz) 05/06 Gsxr 1000 Clutch Mod Parts: 21472-41G10 - WASHER, CLUTCH - $10.09 From 06 Gsxr 750 Opt: 11482-40F00 - GASKET, CL COVER - $8.29 Tools: 13/64 Drill bit, 30mm, 12mm, 10mm, 8mm sockets,
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationHOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS
HOW TO REPLACE THE SPOILER ON YOUR GEN 3 PRIUS Yup, it happened. The spoiler on your beloved Prius has departed this earth and now is in the great junkyard in the sky. This is how you make it all better
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationRetro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationMaintenance Information
Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard
More informationInstalling AMP-wiring in a New Beetle
Installing AMP-wiring in a New Beetle Vehicle used: New Beetle 2.0i Type 9C (1999) Used set of cables: Dietz 35mm² power cable, double shielded Dietz chinch cable ( 35mm² Professional Line ) First of all:
More informationMustang Clear Lens Instrument Cover (90-93) - Installation Instructions
Mustang Clear Lens Instrument Cover (90-93) - Installation Instructions The below installation instructions work for the following products: Mustang Clear Lens Instrument Cover (90-93) Please read through
More informationINSTALLATION INSTRUCTIONS
HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws
More informationHO Scale AC-12 Gear Box Replacement Instructions
HO Scale AC-12 Gear Box Replacement Instructions Introduction Thank you for your purchase of the HO Scale AC-12 from InterMountain Railway Company. The enclosed gear box kit will increase the speed of
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationTechnical Support (707)
Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationMustang Radiator Conversion DIY. By GearHeadPeter. January 27, 2011
1964-1966 Mustang Radiator Conversion DIY By GearHeadPeter January 27, 2011 We all know that the radiators in our cars are not the best, especially if you have done any customization to the engine, which
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationITEM QTY CHECK PART NUMBER DESCRIPTION
PART #21128 2010 Camaro Cold Air Induction Stage II PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1.
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationM1A1 Thompson Upgrade
M1A1 Thompson Upgrade If you are mechanically inclined at all. This should be no problem. I'll start off with a list of things you will need. Thompson M1A1 Whisky Cigarettes Tools: Flat screwdriver No.
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationWheel Bearing Replacement Passat TDI
Rear Bearing/hub assembly replacement This is a fairly straight forward process. Pictures are not necessary for most of this procedure for a person with skills to do this repair. Anyone who thinks they
More informationL/6.7L DODGE CUMMINS
10/19/2012 2005-08 5.9/6.7 Dodge Cummins FlowMAX Lift Pump Kit # 1050310B - 1-2005-09 5.9L/6.7L DODGE CUMMINS BD FLOWMax V2 LIFT PUMP KIT Installation Instructions P/N # 1050310B PLEASE READ ALL INSTRUCTIONS
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationCHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS
Chemical Mixing System Operating and Installation Instructions for Focus II Mid-Size Walk-Behind Kit #11363A CHEMICAL MIXING SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Phillips Screwdriver
More informationService Manual. LT-5 Lawn Tractor
Service Manual LT-5 Lawn Tractor NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power equipment of the kind described in this publication,
More informationELECTRICAL SYSTEM UPGRADE
NEW CONTROLLER & ELECTRICAL SYSTEM UPGRADE FOR DAIRY TECH, INCORPORATED 10, 30 & 60G PASTEURIZERS Parts to Include 2 Wire ties (Nuts) 2 sticky wire mount pads Large Rubber Grommet (for bottom of electric
More information4 pieces of silicone hose Unless you have AEM then you have 2 2.5, 1 3, and 1 3.5
The parts in your kit: 3 pieces of Mandrel-Bent Aluminized Tubing: 1 Straight 1 45 degree bend with straight section 1 curved section 4 pieces of silicone hose 1 2.5 1 3.5 2 3 Unless you have AEM then
More informationMSD 6AL Ignition Module w/ Rev Control - Installation Instructions
MSD 6AL Ignition Module w/ Rev Control - Installation Instructions The below installation instructions work for the following products: MSD 6AL Ignition Module w/ Rev Control Please read through the instructions
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More information1980 Suzuki GS850GT Stator Replacement by BassCliff (a.k.a.bikecliff)
1980 Suzuki GS850GT Stator Replacement by BassCliff (a.k.a.bikecliff) Greetings to those of you who ride the classic GS series motorcycles from Suzuki. This documents my first experience replacing my stator.
More information1999 BMW K1200 LT: Plastic Removal
1999 BMW K1200 LT: Plastic Removal Well, it had to happen. While removing the plastic that covers the handle bars to see where to route power for GPS and/or radar detector the tip of the torx driver fell
More informationDIY: Repairing/Replacing the Timing Chain Tensioner
DIY: Repairing/Replacing the Timing Chain Tensioner By Saki GT - February 8, 2012 [youtube=http://www.youtube.com/watch?v=24cil5_9yvq] The above video is an example of how a bad Timing Chain Tensioner
More informationGo-ped ESR750 / ESR750EX Rear Brake Installation Instructions
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped
More informationRAMPAGE POWER LIFT RAMP
RAMPAGE POWER LIFT RAMP INSTALLATION AND OPERATING INSTRUCTIONS (3/10/07) The Rampage Power Lift Ramp is the fast, easy, and safe way to load a motorcycle into a truck. One person can load or unload a
More informationINSTALLATION INSTRUCTIONS FOR MK4 VOLKSWAGEN JETTA (BORA) /GOLF 1.8T, 2.0L, VR6, & R32 MODELS ALSO FITS ALL MODELS OF SEAT LEON & TOLEDO
CI100001 INSTALLATION INSTRUCTIONS FOR 1999.5-2005 MK4 VOLKSWAGEN JETTA (BORA) /GOLF 1.8T, 2.0L, VR6, & R32 MODELS ALSO FITS ALL MODELS OF SEAT LEON & TOLEDO Thank you for choosing to purchase a Carbonio
More informationThe drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful.
Last Revision: 10JA2010 1969 THRU 1976 GM A & F-CAR STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationPypes Polished Shorty Headers (05-10 V6):
Pypes Polished Shorty Headers (05-10 V6): Introduction: The kit comes complete with replacement hardware and gaskets and can be easily done in your driveway. The hardware supplied for install includes
More informationWalthers/Life-Like USRA Steam Locomotive
North Raleigh Model Railroad Club Installing Decoders in N Scale Locomotives Detailed Instructions Walthers/Life-Like USRA 2-8-8-2 Steam Locomotive by David Derway May 17, 2010 Table of Contents Introduction...
More informationPacific Antenna 40m 15m SOTA Tuner
Pacific Antenna 40m 5m SOTA Tuner Parts List Inventory Component Quantity Note SWR Indicator Kit SWR Bridge Kit T50-6 toroid Yellow toroid core Polyvaricon Variable Capacitor Polyvaricon shaft screw.6
More informationBottom Mount Seat Mount Installation & Wiring Instructions
E81/E87/E90/E91/E92/F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Bottom Mount Seat Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping
More informationDYNACO STEREO 120 C7 REPLACEMENT MANUAL
DYNACO STEREO 120 C7 REPLACEMENT MANUAL 2013 AkitikA, LLC All rights reserved Revision 1p03 April 29, 2013 Page 1 of 15 Table of Contents Section 1: About This Manual... 3 Who Should Attempt this Project?...
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationHow to install the Barnett clutch and the stronger Oil Pump Drive Gear
How to install the Barnett clutch and the stronger Oil Pump Drive Gear Written by WildFred I m from Germany so please excuse my English and the spelling. The following procedure is a combination of the
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationTraditional method Oil Change Instructions For VW 1.9 TDI
Traditional method Oil Change Instructions For VW 1.9 TDI Created by DeafBug This document provides instructions on changing the oil and filter on a VW 1.9 TDI engines. All the pictures here are taken
More informationREPLACING A COLEMAN MACH FAN MOTOR
REPLACING A COLEMAN MACH FAN MOTOR Recently the fan motor on our front AC froze up. I ordered a new motor from Amazon https://www.amazon.com/gp/product/b007vjub9s/ref=oh_aui_detailpage_o00_s00?ie=utf8&psc=11
More informationDesktop 5.5 Z Axis Retrofit
Page 1 Kit parts Desktop 5.5 Z Axis Retrofit Carriage plate with stop bolt and Z proximity switch installed Zip ties Spare bolts Spindle mounting plate with stop bolt, spring mount, and rail Z proximity
More informationRS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR JEEP WRANGLER ALL MODELS.
RS-2 SINGLE ACTION REAR BUMPER WITH TIRE CARRIER INSTALL MANUAL FOR 2007-2016 JEEP WRANGLER ALL MODELS. Rear Bumper Installation Instructions 1) Remove factory rear bumper, (this includes all tow hitch
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationGrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Boost Control Solenoid Updated 4/14/15
GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Boost Control Solenoid Updated 4/14/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Boost Control
More informationAccel 300+ Ignition Control System (84-95) - Installation Instructions
Accel 300+ Ignition Control System (84-95) - Installation Instructions The below installation instructions work for the following products: Accel 300+ Ignition Control System (84-95) Please read through
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationMercedes Benz ABC Hydraulic Valve Block Solenoid Oil Seal Repair Fix Rebuild Kit Seals O-Rings Overhaul Install Instructions
instructables Mercedes Benz ABC Hydraulic Valve Block Solenoid Oil Seal Repair Fix Rebuild Kit Seals O-Rings Overhaul Install Instructions by x8rltd The Problem Vehicle sags on one or more corner after
More informationINSTALLING A 1977 THRU 1982 C3 STEERING COLUMN INTO A EARLIER 1969 THRU 1976 MODEL CORVETTE
Last Revised: 23FE2011 INSTALLING A 1977 THRU 1982 C3 STEERING COLUMN INTO A EARLIER 1969 THRU 1976 MODEL CORVETTE Why Make This Installation Starting in 1977 and carrying thru 1982, the C3 Corvette steering
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationThe Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationMaintenance Information
45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.
More informationNORTHSTAR TRAILERS. Assembly Guide for SPORTSTAR II Trailer
NORTHSTAR TRAILERS Assembly Guide for SPORTSTAR II Trailer Congratulations! You are the proud owner of a NORTHSTAR trailer. Please follow the instructions and steps in this manual for proper assembly.
More informationReplacing the Gear Drive Motor Assembly and GFCI Module for Operation with the Chain Drive Motor Assembly
Replacing the Gear Drive Motor Assembly and GFCI Module for Operation with the Chain Drive Motor Assembly Kit Contents B00009035-3 Motor Drive Assembly (Return original to CMI) B00007698-8 GFCI Module
More informationBachmann Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann 2-6-6-2 Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital
More informationShelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools:
Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item #53611 Installation Time: 1 Day Required tools: Phillips Screw driver 10mm Socket + Ratchet/Wrench 8mm Socket + Ratchet/Wrench 5mm Socket + Ratchet/Wrench
More informationWolverine Turn Signal / Horn Kit 2102
All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationInstructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs)
Instructions for repairing the 1986-87 F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Lonsal@adelphia.net CAUTION: Completely read and understand the instructions before proceeding. There are some
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationInstalling the Audiovox CCS-100 Cruise Control.
Installing the Audiovox CCS-100 Cruise Control. This article was written by: Lon Lawrence w650kawasaki@leaco.net Cruise Control : Audiovox CCS-100 ($89) Webpage : www.summitracing.com Message: I've installed
More informationThis is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX
Adjusting the valve clearance on a 2L V6 FTO engine This is a guide to assist you adjust the valve clearance on a 2l V6 MIVEC engine found in a Mitsubishi FTO GPX Disclaimer: This guide is to assist you
More information