Installation guide Audi A6 4F APS+

Transcription

1 Time for installation is about 5 hours. Installation guide Audi A6 4F APS+ Please disconnect the battery before you are going to start the installation! note: This manual is for experienced people in retrofitting. After Installation the system has to be coded by an Audi dealer: MMI 2G: Address 76 (Parkassist) activation of optical display Address 07 (display front) chanal 01, current value +4 Address 19 (Can Gateway) Byte 00 Bit 7 needs to be set to 1 MMI 3G: Address 76 (Parkassist) activation of optical display Address 5F (main unit) Byte 7 Bit 0 needs to be set to 1 Address 19 (Can Gateway) Byte 00 Bit 7 needs to be set to 1 You should check all components you need before installing: wiring control unit - sensors wiring sensors front 4 suitable sensors in the colour of the car control unit PDC for optical display in MMI buzzer front including button PDC For drilling the wholes into the bumper you will need a 23mm driller ( Forstnerbohrer ). For fitting the sensors you will need a hot glue gun as well as sandpaper. Parts as follows have to be removed: Bumper front Cover above the wheel left and right Glove box Entry rail right, front and back Cover B-post right Back seats Cover trunk in the middle Cover trunk right Cover underneath the steering wheel

2 The control unit for PDC is located behind the trunk cover on the right hand side. Remove the middle cover of the trunk. Pull of the metal plate of the trunk. Remove the cover by pulling on the right hand side of the trunk like showing on the image. Remove the back seats. Pull the seats out of the locking. Remove the cover of the B- post. Pull the cover beginning from the ground up to the roof. Pull the lower cover in direction of the roof. It is fixed on the ground. Please remove the glove box. Therefore remove the cover on the right hand side and remove the screws which are located behind. Remove all screws underneath and disconnect all connections behind. Wire the harness starting from back seat in the front direction to the fuse box. Please wire the split to the buzzer and button as well. Please wire the harness up to the trunk in the back and connect it to the control unit. The two loose wires have to be plugged into the brown 16-pole connector which is already part of the harness. The chamber where to plug in the two wires is printed on the wires. Now you can wire the loom for the buzzer and button PDC. Therefore you have to pull the clima control unit (it is quite tough). Remove the cover underneath the steering wheel as well. The button PDC is located above the clima control unit right hand side. The buzzer is located in the footwell area (driver side) on the centerconsole. The wholes for mounting are already there.

3 Connect the wires to the suitable places. The wires are printed so you can not do a mistake by connecting. The Fuse box ST1 (image) has got steady plus. The Fuse box ST2 (image) has got ignition plus. CAN high and low have to be connected to the CAN connector (image). Original colour of CAN high is Orange/Green. Original colour of CAN low is Orange/Brown. The ground point is located in the foot well of the passenger side as well. Connect the brown wire from the PDC button to the ground. The Gray wire is for the lightning. Connect it to the Gray/Blue wire from Connector lightning switch. Remove the front bumper. Remove the cover and loose the screws located underneath.

4 Remove the cover above the wheel complete on the right hand side. Loose the cover on the left side just on the front. Loos the located screws like shown on the image. Pull the bumper gently out of the locking and disconnect all the plugs behind. Lay the bumper on a soft surface in order to safe it for scratches. Drill gently (inside) with a 3mm driller a small whole on the marked places. Drill now from outside with the 23 mm driller the 4 wholes. Put the sensors into the wholes and adjust them properly. The sensors should be even with the surface. Fix with the hot glue gun the sensors (inside).

5 Connect the wiring for the sensors and fix them with stripes on the bumper. Put the wiring coming from vehicle inside through the rubber beak near the A-post right hand side. You will reach the right wheel arch. Please connect the wires with the loose 10-pole connector. The wires are printed. Now you can start with mounting the parts back on the original location. Please code the system by an Audi Dealer. After coding the system you have to do an MMI Reset. In case of successful installation you should see display as follows: The button is for the following using: You can activate the PDC until a pace of 15 km/h for example by parking in a garage. You can deactivate the system by using the rear gear.