Installation instructions
|
|
- Bartholomew Cox
- 6 years ago
- Views:
Transcription
1 Service Installation instructions Audi A4/A5 (B8 series) 2008 Engine sound system For scope of delivery 8T * Audi Genuine Accessories Service Department. Technical Information
2 Service Contents 1 General notes Parts overview Preparations Assembly overview of the electrical connection Mounting the control unit connecting to the on-board supply Assembly overview of the 4-cylinder TDI exhaust system Assembling the exhaust system: 4-cylinder TDI Assembly overview of the 6-cylinder TDI exhaust system Assembling the exhaust system: 6-cylinder TDI Final tasks All rights reserved. No reproduction without prior agreement from publisher. Copyright 2012 Audi AG, Ingolstadt Printed in Germany
3 1 General notes Please read and take note of these WARNING, Caution and Note descriptions before carrying out maintenance or repair work. WARNING Text with this symbol contains information concerning your safety and indicates potential accident and injury risks. Caution Text with this symbol indicates the risk of damage to your vehicle. Note Text with this symbol contains additional information. The pages that follow contain all of the information (subject to technical changes) needed for installation of the sound exhaust system. Installation of the sound exhaust system can only be performed by a qualified workshop. Special tools, test equipment and vehicle-specific literature will be needed to perform the installation. Incorrect installation can result in personal injury, damage to the vehicle or damage to other vehicles. Audi AG shall not accept responsibility in the event of failure to comply with these assembly instructions. 1 General notes 1
4 2 Parts overview The sound exhaust system can be retrofitted on both left and right-hand drive vehicles. Parts required: Assembly set 8T Comprising: Installation instructions - Audi A4/A5 (B8 series) 2008 Units Part number Description 1 8T Actuator, left 1 8T A Actuator, right 2 8T Adjustable trim panel, chrome black 6 Stainless steel pop rivet, 4 x 9.5 mm (V2A) 2 1K M Clamping sleeve 1 8T Wiring harness 1 8T * Control unit 1 8T Control unit holder 1 8T Sound exhaust system dual nozzle 1 Installation instructions Check the parts to ensure they can be installed in the respective vehicle! You will also need the following for vehicles with 4-cylinder TDI engines: Assembly set 8T A Comprising: Units Part number Description 1 8K E Middle silencer, complete 1 8K F Mounting for middle silencer 2 N Hexagon nut with washer 1 8K M Mounting for end silencer, right 1 1K M Clamping sleeve 1 N Securing nut for end silencer, right 1 8F Heat shielding plate for Cabrio and Sportback 1 8K Heat shielding plate for other vehicles 4 N Securing nuts for heat shielding plate 4-cylinder TDI engines require the diffuser for the dual exhaust system Electronic parts catalogue. 2 2 Parts overview
5 3.1 Preparations Disconnect the battery -A-. Remove the right and left luggage compartment trim Rep. gr. 70. Remove the sill panel(s) from the right side of the vehicle Rep. gr. 70. Remove the glove compartment Rep. gr. 68. If installed, remove the control unit for the digital sound package -J525- incl. holder Rep. gr. 91. Right-hand drive vehicles Remove the rear seat bench Rep. gr. 72. Remove the centre console Rep. gr. 68. Remove the dash panel cover on the driver side Rep. gr. 68. Installation instructions - Audi A4/A5 (B8 series)
6 3.2 Assembly overview of the electrical connection 1 - Electrical connection CAN bus 2 - Retrofit wiring harness route for lefthand drive vehicles 3 - Retrofit wiring harness route for right-hand drive vehicles 4 - Electrical connection earth q 9 Nm 5 - Electrical connection power supply 6 - Electrical connection right sound activator 7 - Electrical connection left sound activator 8 - Control unit, sound AGA 9 - Nut q 9 Nm Installation instructions - Audi A4/A5 (B8 series) Mounting the control unit connecting to the on-board supply Centre the control unit holder on the insulation matting and mark the drill points -1-. Punch mark the drill points. Drill the holes using a 3.0 mm drill bit (angle drill, cordless screwdriver). Make sure that the clearance to wires and the vehicle body is sufficient. Caution Do not drill into any wires! For reasons associated with corrosion protection, use a vacuum to continually collect the drilling chips while drilling. Corrosion damage due to drilling chips is not covered by the vehicle's warranty. 4
7 Drill out the holes to 5.0 mm. Deburr the holes thoroughly. Carefully remove all chips from drilling, e.g. using a workshop vacuum cleaner. In order to provide adequate protection against corrosion, apply the following products with a brush. Single-component primer filler/surfacer LGF /A3 Two-component vario filler/surfacer, grey LGF A3 Audi paint to match the vehicle's colour Body cavity preserving agent D.330.KD2.A1 Position and rivet the control unit holder on the insulation matting. Insert the control unit on the retrofit wiring harness, making sure it engages. Screw the control unit to the holder. Lay the retrofit wiring harness along the standard wiring harness to the relay and fuse carrier F -SF-. If the appropriate equipment is in place, use the cable ties with clip provided to secure the retrofit wiring harness to the rear panel. Lay the connector for the actuators to the corresponding wire grommets -arrow-. Note The clearance for the actuators is created by mounting the actuators Assembling the exhaust system: 4-cylinder TDI on page 9 and/or Assembling the exhaust system: 6-cylinder TDI on page 13. 5
8 Loosen the fuse carrier F -SF- and unclip the fuse carrier - E-. Unpin the lilac/white wire and pin it into the connector housing 1J provided. Pin the open wire end lilac/white into the vacated slot in relay carrier -E-. Connect the two free connectors, making sure they engage. Up to and including model year 2011: Unclip fuse carrier ST4. Unpin the wire from the fused outgoing circuit in chamber 3 Pin the purple/white wire from the AGA wiring harness into the vacated chamber Pin the unpinned wire from the vehicle wiring harness into the connector housing provided (1J ). Pin the unpinned wire from the vehicle wiring harness into the connector housing provided (1J ) and connect to the connector (1J ) from the AGA wiring harness. Check for secure engagement. If there is no fuse in slot 3: Pin the purple/white wire from the AGA wiring harness into the empty slot for fuse 3 (fuse carrier ST4). Insert fuse 15A (N ) into slot 3. Screw the earth wire onto the earth point on the right-hand side of the luggage compartment. 6
9 Left-hand drive vehicles Lay the retrofit wiring harness on the standard wiring harness along the right sill and glove compartment to the data bus diagnostic interface -J533- -A-. Right-hand drive vehicles Lay the retrofit wiring harness on the standard wiring harness along the rear bench seat and centre console to the data bus diagnostic interface -J533- -A-. All vehicles Disconnect the connector -A2-. Open the plug. Unpin the orange/brown wire (slot 6) and pin into slot 2 with the connector provided 4B Pin the orange/brown wire of the retrofit wiring harness into the vacated slot. Unpin the orange/black wire (slot 16) and pin into slot 1 with the connector provided 4B Pin the orange/black wire of the retrofit wiring harness into the vacated slot. Connect the two free connectors, making sure they engage. Secure the retrofit wiring harness to protect against noise and abrasion. Note The assembly should be carried out after the assembled exhaust system is sound-tested. The control unit must not be coded. 7
10 3.4 Assembly overview of the 4-cylinder TDI exhaust system 1 - Mounting 2 - Clamping sleeve q Install so that it is free from tension before tightening the exhaust system Rep. gr Nut q 23 Nm 4 - Screw q replace q 20 Nm 5 - Nut q replace q 20 Nm 6 - Mounting 7 - Actuator 8 - Exhaust tip q 2x q position according to the body version concerned 9 - Pop rivet q 6x 10 - Nut 11 - Shield q select according to the body version concerned Parts overview on page 2 q retrofit on the right side of the vehicle 12 - Actuator 13 - Silencer q replace Installation instructions - Audi A4/A5 (B8 series)
11 3.5 Assembling the exhaust system: 4-cylinder TDI Detach the pipe clip -1-, and support the flex pipe -2-; secure if necessary. Caution Risk of damage to the decoupler. Do not bend the decoupler more than 10 Do not place any strain on the decoupler Do not damage the wire mesh on the decoupler Unscrew the exhaust pipe holder and remove the rear part of the exhaust system. Dispose of pipe clip -1-. Removing the Cw trim -3-: Unscrew nuts -1-, remove clip -2- and remove and discard the Cw trim -3-. Installation instructions - Audi A4/A5 (B8 series) 2008 Removing the shield plate -2-: Unscrew nuts -1- and remove shield plate -2- from the left side of the vehicle -2-. Remove and discard the grommets -arrow- on the left and right side of the vehicle. Guide the advanced wires of the retrofit wiring harness from the vehicle interior through the holes and insert wire grommets. 9
12 Select the right shield plate from the assembly set to match the vehicle type Page 2. Assemble the shield plate on the left and right (from the assembly set), paying attention to the position of the wires below and the edge of the shield plates -arrow-. Remove the diffuser and install the dual diffuser Rep. gr. 63. On the Audi A5 Coupé and Audi A5 Cabrio only Special tools and workshop equipment required Chain pipe cutter -VAS Shortening the middle silencer at right angles using the chain pipe cutter -VAS 6254-: X - 60 mm Continue for all vehicles Position the mountings -1- on the middle silencer - 2x Fit the new clamping sleeve such that the screw ends do not protrude over the bottom edge of the clamping sleeve. The screwed connection points to the left, viewed in the direction of travel. Place the middle silencer in the installation position and screw the mountings to the vehicle. Continue to support the middle silencer 10
13 Assembling the exhaust tips Select the punch point to match the body version and drill a 4.0-mm hole. A - Coupé/Cabrio B - Saloon/Avant and Sportback vehicles from model year 2012 C - Sportback vehicles from model years up to and including 2011 Note the installation position of the actuators and insert and rivet the exhaust tips Fig. Aligning the exhaust tips on page 12 Assembling the actuators Position the mountings onto the actuators. Place the actuators in the installation position, attach the connectors, position and tighten the mountings -1-. Position the clamping sleeves -2- central to the separating cut. Installation position: screw fittings forward. Before tightening the clamping sleeves -2-, install the exhaust system so that it is free from tension Rep. gr. 26 and Fig. on page
14 Aligning the exhaust tips Dimension -x- left = dimension -x- right Rotate the clamping sleeves so that the screw ends do not protrude over the bottom edge of the clamping sleeve. Tightening torques Page 8 12
15 3.6 Assembly overview of the 6-cylinder TDI exhaust system 1 - Y-pipe q remains in the vehicle 2 - Nut q 23 Nm 3 - Clamping sleeve q Install so that it is free from tension before tightening the exhaust system Rep. gr Actuator 5 - Exhaust tip q 2x q position according to the body version concerned 6 - Pop rivet q 6 x 7 - Nut q replace q 20 Nm 8 - Mounting 9 - Actuator 10 - Sound exhaust system dual nozzle Installation instructions - Audi A4/A5 (B8 series) Assembling the exhaust system: 6-cylinder TDI Special tools and workshop equipment required Chain pipe cutter -VAS
16 Separate the exhaust pipe at right-angles at the cut-off points at the middle punch point -arrows- using the chain pipe cutter -VAS Loosen the front clamping sleeve -1- and lower the Y pipe -3-. Position the dual nozzle -2- on the Y pipe -3-. Position the plastic or wooden part -1- on the dual nozzle -2-. Hammer the dual nozzle -2- into the Y pipe -3- using the soft-head hammer. The dual nozzle is now in the installation position. Install the Y pipe. Removing shield plates -2-: Unscrew nuts -1- and remove the shield plates -2- from the left and right side of the vehicle
17 Remove and discard the grommets -arrow- on the left and right side of the vehicle. Guide the advanced wires of the retrofit wiring harness from the vehicle interior through the holes and insert wire grommets. Assemble the shield plate, at the same time being aware of the position of the wires below and at the edge of the shield plates -arrow-. Assembling the exhaust tips Select the punch point to match the body version and drill a 4.0-mm hole. A - Coupé/Cabrio B - Saloon/Avant and Sportback vehicles from model year 2012 C - Sportback vehicles from model years up to and including 2011 Note the installation position of the actuators and insert and rivet the exhaust tips Fig. Aligning the exhaust tips on page 16 Assembling the actuators Position the mountings onto the actuators. 15
18 Place the actuators in the installation position, attach the connectors, position and tighten the mountings -1-. Position the clamping sleeves -2- central to the separating cut. Installation position: screw fittings forward. Before tightening the clamping sleeves -2-, set the exhaust system so there is no tension Rep. gr. 26 and Fig. Aligning the exhaust tips on page 16 Aligning the exhaust tips Dimension -x- left = dimension -x- right Rotate the clamping sleeves so that the screw ends do not protrude over the bottom edge of the clamping sleeve. Tightening torques Page Final tasks Connect the battery -A- Rep. gr. 27. Carry out a functional check. 16
19 Secure the retrofit wiring harness using the cable ties provided, to prevent noise and abrasion. Re-install all removed parts. Where necessary, paint the inside of the exhaust tips with matt black paint. Note The genuine AUDI replacement exhaust system holds ECE type approval (E ). It is therefore not necessary to carry any additional documents with the system, or enter information in the vehicle registration certificate. 17
20
Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off.
j a t Front seats 72-1 CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Search Advanced Search Disconnect the battery Ground
More informationOverview of rear lid trim panels
Overview of rear lid trim panels Overview of rear lid trim panels 1 - Rear lid trim (bottom) Exploded view and installing 2 - Rear lid trim (top) Exploded view and installing vw-wi://rl/a.en-gb.a00.5a50.39.wi::46107222.xml?xsl=3
More informationInstallation instructions, accessories. Electric engine block heater, connector outlet, 4-cyl
Installation instructions, accessories Instruction No 31359444 Version 1.2 5 Part. No. 31359438 Electric engine block heater, connector outlet, 4-cyl IMG-247665 Volvo Car Corporation Electric engine block
More information1 Cable harness for trailer hitch 3 Supporting plate, detachable ball neck 4 Bolts 12 Detachable ball neck 12a Mount X52 Trailer hitch connector
an3110p8080aa Page 1 of 3 Retrofit trailer hitch AN31.10- P- 8080AA Retrofit trailer hitch 5.11.99 MODEL 163.113 /136 / 154 /172 #A as of 145273, 163.113 / 136 /154 / 172 #X as of 708319, 163.128 / 175
More informationMAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent
More information900 Installation instructions. SCdefault
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationFitting Instructions
Reverse Park Assist Suitable for: Nissan Navara Kit Part No: 5466XX NP00 Tow-Pro Wiring Kit Fitting Instructions Accessory Kit Estimated Fitting Time: 0 Minutes FI98 Page 0 of 5 General Notes Read through
More informationRepair manual for Exchanging locking mechanism sensor JSK37C
Repair manual for Exchanging locking mechanism sensor JSK37C JSK_12_48 ZDE 199 7 12 7/213 1 Foreword Table of contents Page Sensor-enabled fifth wheel couplings are parts that must comply with very high
More informationRemoving and installing the dash panel
Стр. 1 из 6 Removing and installing the dash panel Removing: WARNING Disconnect battery earth strap Electrical System Rep. Gr.27. Removing the centre console Chapter. Remove the steering wheel Chapter.
More informationParts and Accessories Installation Instructions
Parts and ccessories Installation Instructions Installation Kit Mini dditional Instruments MINI (R 5/R 53) The installation time is approx.. hours, but this may vary depending on the condition of the car
More informationORIGINAL MINI ACCESSORIES. INSTALLATION INSTRUCTIONS.
ORIGINAL MINI ACCESSORIES. INSTALLATION INSTRUCTIONS. Retrofit Kit Additional Headlight MINI 3-door (F56) MINI 5-door (F56) MINI CLUBMAN (F54) MINI CONVERTIBLE (F57) MINI COUNTRYMAN (F60) Installation
More information57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool
57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed
More informationSeat belts. Safety precautions for handling pyrotechnic seat belt tensioners WARNING!
Page 1 of 41 69-1 Seat belts Safety precautions for handling pyrotechnic seat belt tensioners WARNING! Testing, removing, installing and repair work must only be carried out by properly qualified personnel.
More informationTrim panels on model 124 as of 07/
amb def Installation Instructions Trim panels on model 124 as of 07/93 88.07 The trim panels in the ET scope of supply are primed and can be painted before installation to match the vehicle color in accordance
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions R 1 3 5 2 4 F 38 0213 B Basic retrofit kit for hands-free facility for upgrading various mobile phones BMW 7 Series (E38) LHD without telephone preparation
More informationAirbags, servicing. Airbag system, safety precautions WARNING!
Page 1 of 75 69-40 Airbags, servicing Airbag system, safety precautions Checking, removing, installing and servicing may ONLY be performed by qualified personnel. Never perform tests using a test light
More informationVehicle model: VW Golf A5 Variant RHD, 13-pin 05/07 >> VW Jetta A5 Limousine RHD, 13-pin 08/05 >>
Original Zubehör Genuine Accessories Accessoires d Orgine Fitting instructions Electrical installation kit Part number 1K9 055 210 Distributed by Volkswagen Zubehör GmbH The right to modify specifications
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions 5 224 B Installation Kit Headlight Cleaning System Mini (R5/R53) LHD and RHD Installation time approx. 1.5-2 hours, which can vary according to the condition
More informationAudi A4 Current Flow Diagram No. 50 / 1 Edition
Page 1 of 8 Audi A4 Current Flow Diagram No. 50 / 1 Edition 12.2003 5-speed automatic gearbox with Tiptronic From model year 2002 Main fuse On battery Fuse box Dash panel, driver's side Fuse colours 30
More informationAudi A6 Current Flow Diagram No. 35 / 1 Edition
Page 1 of 5 Audi A6 Current Flow Diagram No. 35 / 1 Edition 08.2007 Heated front and rear seats from model year 2005 Notes: For information concerning Position of relays and fuses Multi-pin connections
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions F 46 3 EVA Headlight Cleaning System (SRA) BMW 3 Series (E 46) The installation time is approx. 3.5 hours, but this may vary depending on the condition of
More informationFitting Instructions
Tow-Pro Wiring Kit Fitting Instructions Suitable for: Toyota Hilux / Fortuner Accessory Kit Estimated Fitting Time: 90 Minutes FI807 Page 0 of Issue: Date: /08/08 08 General Notes Safety Notes Suitable
More informationENGINE DISPLACEMENT 2000 NUMBER OF VALVES 16 ENGINE SET NUMBER
MANUFACTURER Subaru TYPE Forester ENGINE DISPLACEMENT 2000 NUMBER OF VALVES 16 ENGINE CODE / NUMBER FA20 DIT VEHICLE CATEGORIES M TRANSMISSION AT VERSION Direct LiquiMax-2.1 PETROL ECU MANUFACTURER / CODE
More informationENGINE DISPLACEMENT NUMBER OF VALVES 16 VEHICLE CATEGORIES
MANUFACTURER Dacia TYPE Duster ENGINE DISPLACEMENT 1200cc NUMBER OF VALVES 16 ENGINE CODE / NUMBER H5F (TCe125) VEHICLE CATEGORIES M TRANSMISSION MT (6-speed) VERSION AFC-2.1 PETROL ECU MANUFACTURER /
More informationSCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :84-35 Sep
SCdefault 900 Installation instructions SITdefault Rear spoiler MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part No.
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions F 53 7 W Retrofit auxiliary heating system BMW X5 (E 53) with M57 engine (diesel) The installation time is approx..5-4.5 hours (see important information),
More informationAssembly instructions Original parking distance control system, Volkswagen
Assembly instructions Original parking distance control system, Volkswagen Set contents: 1 x controller 1 x buzzer 4 x sensor Set contents: 4 x covering rings 4 x protective rings Special tools, test and
More informationOriginal BMW Accessories. Installation Instructions.
Original BMW Accessories. Installation Instructions. Removable trailer tow hitch retrofit BMW 3 Series Saloon (F30) BMW 3 Series Touring (F3) BMW 4 Series Coupé (F32) BMW 4 Series Gran Coupé (F36) These
More informationAccessory Kit Estimated Fitting Time: 120 Minutes
Landcruiser LC00 Tow-Pro Wiring Kit - Landcruiser LC00 Kit Part No: TPWKIT - 005 Accessory Kit Estimated Fitting Time: 0 Minutes FI88 Page 0 of Issue: Date: 7/09/07 07 General Notes Safety Notes Parts
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top Evo Parking Heater e 00 058 Installation documentation Audi A6 / A6- Avant / Audi A7 Sportback.0 and.0 TDI quattro from model year 0 Left-hand drive vehicle Automatic
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationDrive unit. Installing/removing ebike components. Tool: Allen key size 8. ISIS crank-puller. Spider-Tool. Lever (e.g.
Removing the chain wheel Remove the crank arms (Allen key size 8, ISIS crank-puller). Block the rear wheel. Tip: Clamp the brake lever with Velcro. Unscrew the lock ring () with the Spider-Tool (). Caution:
More informationAudi A6. Automatic gearbox multitronic 01J from model year 2005 Notes: Current Flow Diagram No. 22 / 1. Edition For information concerning
Current Flow Diagram No. 22 / 1 Edition 08.2007 Automatic gearbox multitronic 01J from model year 2005 Notes: For information concerning Position of relays and fuses Multi-pin connections Control units
More informationBMW Parts and Accessories Installation Instructions
1 4 BMW Parts and Accessories Installation Instructions INFO 2 5 3 6 TONE SELET FM AM MODE MENU F 38 0393 B Retrofit Kit Onboard Monitor and Navigation System BMW 7 Series (E38) The installation instructions
More informationENGINE DISPLACEMENT NUMBER OF VALVES ENGINE SET NUMBER VEHICLE CATEGORIES. Direct LiquiMax-2.0 PETROL ECU MANUFACTURER / CODE Bosch MED 17.
MANUFACTURER VOLVO TYPE V60 / V70 T4F ENGINE DISPLACEMENT 1600cc NUMBER OF VALVES 16v ENGINE CODE / NUMBER B4164T2 VEHICLE CATEGORIES M TRANSMISSION MT/AT VERSION Direct LiquiMax-2.0 PETROL ECU MANUFACTURER
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS IMPORTANT
For use in cleaning painted metal, glass and other vehicle surfaces. For external use only. Dispose of properly after use. IMPREGNATED WITH 70% ISOPROPLY ALCOHOL TC0d PC TONNEAU COVER INSTALLATION INSTRUCTIONS
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions Park Distance Control (PDC) Rear Retrofit BMW Z4 (E 85) The installation time is approx. 4 hours, but this may vary depending on the condition of the car
More informationInstallation instructions
Service Installation instructions Audi A3 (8V3) 2012 Roof bars 8V3.071.126 for vehicles with bright moulding package (PR no. 4ZB) and roof bars 8V3.071.126.L for vehicles with black moulding package (PR
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationhttps://webista.bmw.com/webista/show?id= &lang=enus&print=1
Page 1 of 12 REP-REP-RAE70M57T2-1112800 Cleaning cylinder heat intake channels and intake plenum (E70US, M57T2) VIN: Vehicle: X' / E70 / off-road vehicle / X5 35d x / M57 / USA / left-hand drive / AUT
More informationCANOPY WIRING PATCH KIT INSTALLATION INSTRUCTIONS Holden Colorado RG
CANOPY WIRING PATCH KIT INSTALLATION INSTRUCTIONS Holden Colorado RG IMPORTANT! Read instructions carefully before installation. It is strongly recommended that installation is conducted by an authorized
More information3.6.1 Brake Lamp Switch
2002 TT/TTS Coupe/Roadster Report a problem with this article The ESP road test ascertains the plausibility of the signals transmitted from sender 1 for brake booster -1- -G201-, sensor -2- for brake pressure
More informationORIGINAL MINI ACCESSORIES. INSTALLATION INSTRUCTIONS.
ORIGINL MINI SSORIS. INSTLLTION INSTRUTIONS. dditional Headlight Retrofit MINI (F56) Retrofit kit number 63 0 40 9 63 0 47 669 63 355 766 63 84 9 dditional headlight retrofit kit, black dditional headlight
More informationTeile und Zubehör - Einbauanleitung
Teile und Zubehör - Einbauanleitung F 38 0027 EVA BMW Parts and Accessories Installation Instruction Park Distance Control (PDC), rear BMW 7 Series (E38) Best.-Nr. 01 29 0 000 791 XII/98 Printed in Germany
More informationFitting Instructions
Tow-Pro Wiring Kit Fitting Instructions Holder Colorado / Colorado 7 Accessory Kit Estimated Fitting Time: 0 Minutes FI7 Page 0 of General Notes Read through the fitting instructions before installation
More informationLUXURY TOPS FITTING INSTRUCTIONS
FIT 1027 LUXURY TOPS T O Y O TA H I L U X M K 8 DOUBLE CAB 1 ST E D I T I O N FITTING INSTRUCTIONS LUXURY TOPS Please read these instructions carefully. If you have any questions regarding the fitting
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationFitting Instructions
Reverse Park Assist Suitable for: Isuzu MU-X Kit Part No: / 5466XX D-Max Tow-Pro Wiring Kit Fitting Instructions Suitable for: Isuzu MU-X / D-Max Accessory Kit Estimated Fitting Time: 0 Minutes FI967 Page
More informationFront bumper (Audi RS6)
63-1 Front bumper (Audi RS6) Assembly overview 1 - Air inlet grille To remove pull grille forward 2 - Air inlet grille To remove pull grille forward 3 - Screw 2.5 Nm 3x 4 - Bumper cover Together with impact
More informationBMW Parts and Accessories Installation Instructions
BMW Parts and Accessories Installation Instructions 46 77 B BMW subwoofer module retrofit kit BMW 3 Series compact (E 46/5) LHD Technical and electrical knowledge required Installation time approx. 1.5-2.5
More information900 Installation instructions. SCdefault
12 788 439 1 SCdefault 900 Installation instructions SITdefault Timer kit MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More information1995 Mercury Grand Marquis GS
AIR BAG SYSTEM CAUTION: Read the following safety precautions BEFORE servicing steering columns on vehicles equipped with air bag restraint system. ALWAYS wear safety glasses when servicing vehicle with
More informationFitting Instructions
Kit Part No: TPWKIT-00 Tow-Pro Wiring Kit Fitting Instructions Suitable for: Mitsubishi Triton Kit Part No: TPWKIT-00 Accessory Kit Estimated Fitting Time: 90 Minutes FI705 Page 0 of Issue: Date: /08/08
More informationHood. Hood, removing, installing and adjusting. Page 1 of 11
Page 1 of 11 55-1 Hood Hood, removing, installing and adjusting 1 - Hood Removing: - Disconnect hose to windshield washer system and unclip. Second person is needed to support and lift hood during removal
More informationEngine, removing and installing
Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers
More informationAir Filter Element, Replacing and Cleaning Housing
Air Filter Element, Replacing and Cleaning Housing Note Only use silicone-free lubricant for assembling the intake hoses. Secure all hose connections with hose clamps that match current standard production.
More informationOriginal BMW Accessories. Installation Instructions.
Original BMW ccessories. Installation Instructions. Trailer tow hitch retrofit (removable version) BMW X5 (E70) BMW X6 (E7) Retrofit kit No. 7 60 2 55 44 Electrical components retrofit kit (for E70 only)
More informationCentral locking system
Page 1 of 11 57-39 Central locking system Assembly overview 1 - Vacuum line 2 - Right-front door lock actuator Removing and installing page 57-12 3 - Vacuum line connectors Disengage harness connectors
More informationVolkswagen New Beetle Body - Exterior 64 Glass, Window regulators (Page GR-64)
64 Glass, Window regulators (Page GR-64) Flush bonded windows Body flange, preparing for glass installation Broken rear window, removing Cleaning off excess adhesive material Curing time Installation instructions
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 004 Installation Instructions Dodge Nitro Diesel from Model Year 007 Left-hand drive vehicle
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationMANUFACTURER Explorer Sport ENGINE DISPLACEMENT NUMBER OF VALVES FIRING ORDER VEHICLE CATEGORIES TRANSMISSION
MANUFACTURER Ford TYPE Explorer Sport ENGINE DISPLACEMENT 3500cc NUMBER OF VALVES 24v ENGINE CODE / NUMBER 3.5L GTDi Ecoboost FIRING ORDER 1 4 2 5-3 - 6 VEHICLE CATEGORIES M TRANSMISSION AT VERSION AFC-2.1
More informationMAKE OF AUTOMOBILE: TYPE: V 70 PISTON DISPLACEMENT: 2521 NUMBER OF VALVES:
MAKE OF AUTOMOBILE: TYPE: V 70 PISTON DISPLACEMENT: 2521 NUMBER OF VALVES: 20V ENGINE NUMBER: B5254T TRANSMISSION TYPE ( MT / AT ) AT VEHICLE CATEGORIES M or N PASSENGER CAR ( M ) TYPE VSI INJECTOR (COLOUR
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationMegane Estate ENGINE DISPLACEMENT NUMBER OF VALVES VEHICLE CATEGORIES
MANUFACTURER Renault TYPE Megane Estate ENGINE DISPLACEMENT 1200cc NUMBER OF VALVES 16v ENGINE CODE / NUMBER H5F (TCe115) VEHICLE CATEGORIES M TRANSMISSION MT(6) VERSION AFC-2.1 PETROL ECU MANUFACTURER
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationOutside Rear View Mirror, Remove and Install
102989Outside Rear View Mirror, and file://c:\program Files\cosids\DATA\TMP\00102989.rtf.html Page 1 of 2 Outside Rear View Mirror, and 1. Move sash window downwards 2. Detach panel for front door inside
More informationFACTORY AIR CONVERSION HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle FACTORY AIR CONVERSION HEAT/ COOL/ DEFROST 1970-72 CHEVROLET CHEVELLE CONTROL & OPERATING INSTRUCTIONS The controls on your
More informationInstallation instructions, accessories - Fuel driven heater 912-D
XC90 Section Group Weight(Kg/Pounds) Year Month 8 87 2002 10 XC90 2003 D5244T, XC90 2004 D5244T, XC90 2005 D5244T AW50/51 AWD, XC90 2006 D5244T, XC90 2006 D5244T AW50/51 AWD D5244T R8703687 Page 1 of 20
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More informationFuel pump unit, changing
1(11) Fuel pump unit, changing Special tools: 981 2270, 981 2273, 981 2282, 998 5972, 999 5484, 999 5485, 999 5561, 999 5666, 999 5673 Safety See first Safety regulations for handling fuel. Preparation
More informationEnglish. Fitting Instructions: Trophy and Trophy SE A and A of 10 A Parts Supplied:
English Fitting Instructions: Trophy and Trophy SE A95086and A950856 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of proven engineering,
More information5. Refer to GTR Workshop Manual, section: and disconnect battery ground cable.
HYDRAULIC HOSE REPAIR REMOVAL PROCEDURE 1. Open door. 2. Turn ignition 'ON'. 3. Power the convertible top to the fully lowered position. 4. Turn ignition 'OFF'. 5. Refer to GTR Workshop Manual, section:
More informationInstallation Instructions Complete set active Sound incl. Soundbooster Audi A8 4H
Installation Instructions Complete set active Sound incl. Soundbooster Audi A8 4H v.2 (04.0.207) Kufatec GmbH & Co. KG - Dahlienstr. 5-23795 Bad Segeberg - e-mail: info@kufatec.de Contents Liability Exclusion
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions Active cruise control retrofit (ACC) BMW 7 Series (E 65, E 66) LHD Important information The retrofit kit is for use within the BMW dealership organisation
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More information1 of 27 7/21/2015 3:33 PM
1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work
More informationRemoving and installing trim panel
Removing and installing trim panel vw-wi://rl/a.en-gb.a03.5106.29.wi::31914802.xml?xsl=3 1. oldal, összesen: 1 oldal Removing and installing trim panel Removing Carefully prise out trim panel -1- in direction
More informationInstallation instructions BasicRelay CR / / 2012
Installation instructions BasicRelay CR0421 7390825 / 00 07 / 2012 Contents 1 Preliminary note................................................. 4 1.1 Symbols used...............................................
More informationSCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :40-05 Sep
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationBrabus SoundXtra for Mercedes-Benz GL350 BT X SX
Brabus SoundXtra for Mercedes-Benz GL350 BT X166-670-SX The product described in the instructions was developed, produced and checked considering the necessary safety requirements. In order to ensure a
More informationBMW-Motorrad Installing LED auxiliary headlights Preparatory work. Core activity
77 51 001 Installing LED auxiliary headlights + 77 51 502 Equipment trim-level variant: LED auxiliary headlights Note Not all the components contained in the installation kit are necessary for installing
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (LX, EX) CIVIC 2- AND 4- DOOR AII 25449 Issue Date SEP 2003 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationReplacing the fuel tank
Page 1 of 11 Replacing the fuel tank Special tools: 999 5720 Preparation Note! On cars up to chassis number 104221 the fuel filler pipe must be replaced when the fuel tank is replaced. Drain the fuel from
More informationVOLKSWAGEN AMAROK MY17> 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK MY7> & PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or
More informationINSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT
INSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT REMOVAL 1. Remove the covers over the heating/air-conditioning system, battery and fluid tank. Disconnect and remove the battery. 2. Remove the
More informationParts and Accessories. Installation Instructions.
Parts and Accessories. Installation Instructions. Park Distance Control (PDC) retrofit kit BMW X5 (E 5) Retrofit kit No. 66 0 0 007 0 66 0 0 4 68 66 0 0 09 685 66 0 0 9 509 Installation time The installation
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More informationContents Copyright...2 General advice...2 Safety instructions...3 References of legal regulations for operation...3 Space of delivery for 37998, 37998
Version 1.05 (22.02.2013) Installation instruction Parking assist Front + Rear Article no.37998, 37998-1, 37998-2 39745 VW Touareg 7P www.kufatec.de Kufatec GmbH & Co. KG Dahlienstr. 15 23795 Bad Segeberg
More informationFOG LAMPS INSTALL KIT
FOG LAMPS INSTALL KIT PT CRUISER INSTALLATION INSTRUCTIONS Read entire instructions thoroughly before starting. For proper aiming of fog lamps, follow procedures in the service manual. NOTES: Left and
More informationPage 1 of 15 1Search ANTENNA 2010 MINI Cooper 1.6L Eng Base 6520 AERIAL ANTENNA 6520090 Removing And Installing/Replacing Aerial Amplifier (FM) Necessary Preliminary Tasks Remove RIGHT REAR LIGHT Unlock
More informationSoumatrix speakers installation guide
Soumatrix speakers installation guide Preface Soumatrix coaxial speakers combine bass and treble loudspeaker in one unit. Just replace the car original bass loudspeaker in each of the front and rear doors.
More informationTurbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.
Page 1 of 50 21-1 Turbocharger system Note: Observe rules of cleanliness Page 21-22. Charge air pressure control connection diagram Page 21-2. All hose connections are secured with hose clamps: parts catalog.
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions Installation kit, sound module MINI (R5) Cooper S (R53) Left-hand drive (LHD) Not suitable for vehicles with option SA 69 (navigation system with on-board
More informationInstallation manual Complete set active Sound incl. Soundbooster Audi A4 8E
Version 1.01 (18.02.2015) Installation manual Complete set active Sound incl. Soundbooster Audi A4 8E Article no. 40566 www.kufatec.de Kufatec GmbH & Co. KG Dahlienstr. 15 23795 Bad Segeberg e-mail: info@kufatec.de
More informationInstallation instructions, accessories. Parking assistance, rear
Installation instructions, accessories Instruction No 31330676 Version 1.4 Part. No. 30758088, 9487266, 30786087, 31359215 Parking assistance, rear Volvo Car Corporation Parking assistance, rear- 31330676
More information