Automatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com
|
|
- James Baldwin
- 5 years ago
- Views:
Transcription
1 Automatic trunk lid retrofit BMW F10 Bj.2011 by laser21 bimmerfest.com This is a short guide to help you retrofit the option SA316 - automatic trunk lid mechanism into your F10. That refers to a motor opening and closing of the lid. The powered version opens and closes the lid slowly with a motor, without option SA316 the lid springs up without motor assistance and has to be closed manually. Parts details You can find details of parts on these two sites Parts needed (5 series F10) There are five main parts needed under the rear bumper. Part numbers can vary by model. Use the resources above to check the exact part numbers. The part numbers also change over time. You will also need different diameter cables with preferably different colors. (1m 2mm 2 red; 1m 2mm 2 brown; 5m 1,25mm 2 yellow; 10m 0,85mm 2 black, 4m 0,85mm 2 orange, 4m 0,85mm 2 green) Part number Part Cost new in Euros or HKFM MODULE Trunk servo lock drive Trunk lock upper module spindle drive left spindle drive right HKFM Module holder 8, trunklid inner switch 26,45 Other parts and their quantity (with some excess, so that you can mess up ) pin connector pin connector 3,3 3x contact pin with cable 1,73 8x contact pin small 0,3 8x contact pin large 0,5 The pictures below show the parts. 3x leaf spring contact small 1,86 2x leaf spring contact large 2,5 3x contact for ground 0, support left cca support right cca 5 HKFM
2 First, start to make your cable-tree which is shown in the above picture connected into the HKFM s A43*1B connector. It s the pin connector. PIN Cable color Where to Length Diamet 1 Red/blue Rear Fuse Box F183(40A) in Z23B 30cm 2mm 2 2 Brown Ground in Z108B 50cm 2mm 2 3 Red/yellow Rear Fuse Box F153(5A) in Z26B 30cm1,25mm 2 4 brown Ground 50cm 2mm 2 5 CAN_H 4m 0,85mm 2 6 CAN_L 4m 0,85mm 2 7 Free 8 Free 9 Free 10 free When you prepare this connector before you start, you save yourself time during the disassembly. Now onto the disassembly.
3 Get some good plastic pry tools, you will need them a lot. After removing all the plugs, carefully remove the whole carpet and the bumper cover which goes off pretty hard. Unplug the pole of the battery and start to remove the old springs by pure force. Be careful, when you remove them, the lid can fall on your head, so secure it in the open position.
4 Its recommended to put in and 170 as reinforcement not shown in pictures. The old spring uses a different fixture point for their joint, so dont worry, the new spring will fit just fine. Put a flat screwdriver under the metal clip on the end of the new springs it makes it easier to clip them onto the joints.
5 Here you can see the HKFM module in its housing and the fusebox released you need access to the back of the fusebox. to make 3 connections 2 coming from the HKFM (fuse 183 and 153) and 1 which will supply the soft close mechanism in the lid. Fuse 183 should be empty, 153 should be occupied, so just make a cable-cable connection, dont try to pull out the pin (its too damn hard ). Prepare a 4m long 1,25mm 2 diameter wire which you have to connect to the fuse 155 in the Z26B block in the fusebox. After you have all three wires connected, you can put the fusebox back in place. Connect the cables coming from both springs into the HKFM. Attach the 2 ground cables coming from the HKFM into Z108B picture shows just one. Now onto the lid itself. Pry all out, push on the sides where the arrows are, remove gently, dont forget to disconnect the small light
6 Mount the soft close mechanism, guiding the bowden like in the picture, also guide the wire coming from the soft close to the lock. Mount it with the help of the rubber plugs. Now attach the bowden and the cable to the lock, and fix it into its position with the big torx screws.
7 The old lock has a 4 pin connector, but you need a 6 pin connector for the new one. Follow the scheme to create the new connector using pin connector.
8 Pull the cable which you connected to the fuse 155 together with a long (10m, 0,85mm 2 ) wire through the tube with help of a hard cable. Connect the Fuse wire to PIN 1 and the thinner long cable to PIN 6. Now we have to take care of the switch which activates the automatic trunk. We slightly have to alter its connector as well. Unused PIN 2 with a new wire (around 20cm long) Attach the new wire to a grey-yellow wire found in this bundle
9 Ok, so the trunk is wired, we now need to connect the last 3 wires which let the car communicate with the trunk the CAN bus wires coming from the HKFM and the long cable coming from the lock mechanism PIN 6. ISTA says the following find the CAN cables in X1551V. I havent found them there. They should be 2 twisted wires, easy to find. So I found them on the other side in the trunk connecting into the Camera module. I followed them from the rear drivers side door into the trunk.
10 they look like this Make the connections, either by splitting the cables, or just remove the isolation and attach it to their side. Now comes the funny part Lead the only cable left to the front around the passenger side into the junction box behind the glove box. The pictures come from a right side drive car, nonetheless, they are the same in the left side drive car. You DO NOT have to remove the plastic entrance step covers. Just push the cable between the carpet and the covers, pry them up a little bit to easy the cable underneath them. When you have the cable at the front passenger footwell area start to remove the glovebox.
11 Gently pry out the wood trim with the middle vents to acces the torx screws of the glovebox.
12 There are some hidden screws, you should not forget. If you have a DVD changer, you have to remove it first. It has 5 torx screws holding it to the glovebox and one cable that unplugs on the back. Be careful with the USB port! Also there is a connector on the middle side of the glovebox which you have to disconnect. After that you either fully remove the glovebox or just let it hang on the USB cable.
13 You will see the junction box and the big blue connector. The black connector slides out from the side of the blue housing. After that, find the PIN 13 and plug in the cable. Now you can try to assemble everything back The trunk should work after you attach the battery, but it might still have some issues that need to be taken care of by coding and initializing by ISTA. Please post any suggestions to this guide to my . Also, when it helped you, let me know! Paypal if you would like to give out a beer for me
2015 Copyright Maxspeed-Motorsports.com
1 Porsche PCM 3.1 Backup Camera Installation Instructions. Thank you for purchasing your product at www.maxspeedmotorsports.com Before you start please understand that these installation instructions are
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationSmart Opener Retrofit by Richard Bevan (bimmerfest riku2)
Smart Opener Retrofit by Richard Bevan (bimmerfest riku2) Document history V 1.0 02.04.2015 Document created. Introduction This document tells how to retrofit the smart opener to a 2011 BMW 5 series (F10).
More informationAudi A8 ( ) MMI swivelling unit repair manual
Audi A8 (2003-2007) MMI swivelling unit repair manual Tools which you will need: two pcs screwdriver (any kind, for vent removing ) (you can cover the metal part with any tape to prevent making scratches
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More information2010 Toyota Prius model II Head Unit Upgrade
2010 Toyota Prius model II Head Unit Upgrade Monday, December 21, 2009 Disclaimer: Use this document and its contents at your own risk. Forward: Huge thanks to those members on Priuschat.com that forged
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationFULL SIZE RANGE ROVER REMOTE STARTER INSTALLATION INSTRUCTIONS
2010-2012 FULL SIZE RANGE ROVER REMOTE STARTER INSTALLATION INSTRUCTIONS During your first installation of this product, you will benefit from these complete instructions. After performing two or three,
More informationI want to try my hand here at doing a TacoBill write up so here it goes.
Here is part 3 of my tutorial for the conversion of my Shaker 1000 to the Kenwood DNX7100 Navigation / Head Unit. With the 7100, my new system will include the Kenwood I-pod Adapter (P.I.E. KNW/USB-AV),
More informationInstallation Directions for FINGER STICK and Blocker Plate
Installation Directions for FINGER STICK and Blocker Plate What is a Finger Stick? A Finger Stick is a simple circuit that modifies the MAF signal on LLY and LBZ engines (not LB7 engines) to expected levels
More informationYOU MAY WANT TO FIRST TRY TO LOOSEN THE FILTER HOUSING
2005 XC90 Tune-up (5-cyl) Including: Oil Change - Spark Plugs - Fuel Filter - Cabin Filter First off - let me say that I am an amateur (at best) mechanic, and I claim no responsibility for whatever you
More informationPeugeot 406 Coupe: Delocking your boot V.1 April 2005
This is a first stab at a DIY guide to de-locking your 406 Coupe. It isn t a hard modification to do yourself, but you do need to be confident working on your cars electrics and removing and refitting
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationInstalling AMP-wiring in a New Beetle
Installing AMP-wiring in a New Beetle Vehicle used: New Beetle 2.0i Type 9C (1999) Used set of cables: Dietz 35mm² power cable, double shielded Dietz chinch cable ( 35mm² Professional Line ) First of all:
More informationHeater Core Replacement
Heater Core Replacement Ok, I just finished replacing the heater core in my dad's '94 840Ci. While this is fresh in my mid I thought I would outline the procedure, I'm going from memory here, so I will
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More information2005 and 09 Mustang install instructions Sequential / Chase Unit Partial Plug-N-Play Kit Meter4it Eng. Updated: 3/28/09
Updated: 3/28/09 Verify content of kit: 1- Unit with wiring harness 1- Red power wire with 15 amp fuse 1- Color instruction 2- Velcro for mounting 1-Driver taillight harness 1- Passenger taillight harness
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationVTCM Installation Manual Table of Contents
VTCM Installation Manual Table of Contents 1. Introduction:... 2 2. Disclaimer:... 2 3. Software / Drivers:... 2 a. Plugging in the controller:... 2 b. Install 4.0.NET Frame work:... 3 c. Install COM port
More informationBODY-24, Late Model 944 ( and Newer) Dash Replacement
BODY-24, Late Model 944 (1985.5 and Newer) Dash Replacement Introduction Replacing the dash in a late model 944 is not overly difficult. However, it is very tedious and a lot of patience is required. It's
More informationBMW 3 SeriesE90 - E93 Factory Alarm Install
Instructions on a BMW 3 Series Factory Alarm Install. Written By: Danielle 2017 guides.drivediy.com Page 1 of 9 INTRODUCTION Tips on how to install a BMW 3 Series Factory alarm. Credit: CC 330i[E90Post.com
More informationMounting a Garmin to an R1150R Motorcycle
Mountain a Garmin GPS on your BMW Motorcycle Introduction The following document will describe how I mounted my Garmin 1490T GPS unit to my motorcycle. Garmin makes a specific GPS unit (the Zumo) for motorcycles
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationHow to change Swirl Flaps, on Diesel BMW
How to change Swirl Flaps, on Diesel BMW I am now going to show you how i did it on my car. May'sedition of Total BMW (still in WHSmiths) did a cover on how to change and modify Swirl flaps on a 330d engine,
More information2010 Toyota Prius Fog Light Retrofit
2010 Toyota Prius Fog Light Retrofit A DIY prospective Last updated: Friday, December 25, 2009 *** Disclaimer Use this document and its contents at your own risk! *** Forward: This document was compiled
More informationHow to Replace the B2 Piston Bore Seal
Page 1 Home Cars for sale Trucks for sale Where we are Links to other diesel sites About us Why diesel? Diesel Videos How they work How they sound FAQ Dodge Diesel Maintenance tips, parts and DIY DVD's
More informationHow To: Thermostat change - D8 V6 194bhp
How To: Thermostat change - D8 V6 194bhp Firstly, take off the Air Filter hoses and connectors and lift off. This leaves you with this workable space... I started with taking the two bolts out of the cable
More informationFitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE
Fitting the Bell Auto Services (B-A-S) TDV6 EGR Blanking Kit to a 2006 model Discovery 3 TDV6 HSE Before I describe how I did this, I must first thank other members of the Disco3.co.uk forum (namely J,moore
More informationBMW E61 Hydraulic Pump replacement instructions
BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part
More informationBEN-HUR Bentley head unit replacement kit (INSTALLATION MANUAL)
JH (rev 1.4) 31-03-17 BEN-HUR Bentley head unit replacement kit (INSTALLATION MANUAL) DO NOT ATTEMPT TO FIT THE BEN-HUR UNTIL YOU HAVE READ THE INSTALL MANUAL Overview The BEN-HUR allows you to install
More informationDoor panel removal F07 5 GT
Things needed Decent plastic trim removal tools Torx 30 Spare door clips 07147145753 I got away with a set of 5 but if I did it again I d be cautious and get 10. From prior experience if they are damaged
More informationM.O.S.T HUR MB OPTI-1 NTV-KIT421 Mercedes Benz Head Unit Replacment Interface
M.O.S.T HUR MB OPTI-1 NTV-KIT421 Mercedes Benz Head Unit Replacment Interface Brendon Martell January 15,2013 Included Parts: OPTI-1 INTERFACE Needed Tools: Power, RCA input and remote turn on harness
More informationO ring installation guide
AtomicRice.com O ring installation guide Tools and materials needed: 1) Phillips Screwdriver ( one medium and one large head) 2) Small or Medium sized flathead screwdriver or thin rigid shim 3) Vaseline
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationPage 1 of 14 This install requires work on your supplemental restraint system and could cause injury or damage to your car. If you are not comfortable performing the steps detailed here then do not attempt
More informationBMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li)
Page 1 of 11 BMW 745Li E65/E66 Rear Brake Pad Replacement By Jerry Incollingo (Jerry 745Li) This guide will detail how to change the rear brakes on late model BMW E65 / E66 s. It was performed on a 2003
More informationABS/DSC/ASC REPAIR. Although it may look like the 'black box' is pretty simple with just a bunch of solonoids...
ABS/DSC/ASC REPAIR The E38's produced after 1997 can suffer from ABS failure that bungs up fault lights for ABS, ASC and Brake Warning, the lights are all orange (warning) rather than red (failure). This
More informationMY-CUE VIM Video in Motion for MyLink/CUE NTV-KIT495
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 MY-CUE VIM Video in Motion for MyLink/CUE NTV-KIT495 BHM Overview The MY-CUE VIM enables video in motion in select 2013+ GM
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationPorsche 911 Gear and Pod Odometer Repair
www.odometergears.com Porsche 911 Gear and Pod Odometer Repair http://efinnegan.com/porsche/repair%20maintenance%20and%20miscellaneous%20info/odometer-rebuild.htm http://p-car.com/diy/odometer/ *************************************************************************************************
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationInstallation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-
Installation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-1. This instruction shows how to replace the OEM intercoolers with do88 performance intercoolers. At this type of installation
More informationInstallation guide Audi A6 4F APS+
Time for installation is about 5 hours. Installation guide Audi A6 4F APS+ Please disconnect the battery before you are going to start the installation! note: This manual is for experienced people in retrofitting.
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013
ALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013 Level of difficulty: If you follow these directions, moderate, hardest part is aligning the alternator back for repositioning. Length
More informationBMS JB Stage1 n63/n63tu/s63/s63tu Install Guide
BMS JB Stage1 n63/n63tu/s63/s63tu Install Guide Last updated 1/30/2013 Use subject to terms and conditions posted at burgertuning.com/terms Please note there are 4 variations of BMW's twin turbo V8 motor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC AII 24171 S 2- AND 4-DOOR Issue Date (DX, HX) AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationRedlineGoods Tacoma Installation Manual
RedlineGoods 2016+ Tacoma Installation Manual AUTOMATIC SHIFT BOOT AND EBRAKE BOOT Press down on the factory shift boot collar to disconnect it from the shift knob. Unscrew shift knob Pull up on the rear
More informationSTEP #1: Remove the wheels from the truck. There are (6) 21mm lug nuts holding each wheel on... Remember Lefty Loosy, Righty Tighty.
- CustomTacos.com Page 1 of 36 How-To: Toytec Lift Install Read all of these install instructions prior to installing Toytec's suspension lift. I cannot be held responsible for any damages or personal
More informationBMW 3Series (E46) Installation Guide StealthOne Version 1.6
BMW 3Series (E46) Installation Guide StealthOne Version 1.6 Copyright Fontana Enterprises, 2008 All rights reserved. Product Information Copyright Copyright Fontana Enterprises, 2008 All rights reserved.
More informationE46 FUEL FILTER CHANGE Pics from CI
1 of 10 5/3/2010 1:48 PM E46 FUEL FILTER CHANGE Pics from 2001 330CI Bellows Expansion Joints Metal Bellows Expansion Joints in Every Style from Flexicraft www.flexicraft.com/metal_bellows Ask a BMW Mechanic
More informationHasse Mods for the Ampeg J20 Guitar Amp
Hasse Mods for the Ampeg J20 Guitar Amp The following is adapted from a post I put up on The Gear Page, in the Amp Techincal forum. It shows the mods I did to my Ampeg J20. Okay, here s my mods for this
More informationRevision Date: Building a dual pump system for an open boat. Description:
Disclaimer: The information is provided as-is. The author(s) accepts no liability for the accuracy, availability, suitability, reliability and usability. The following information is in the public domain
More informationUse subject to terms and conditions posted at
Use subject to terms and conditions posted at http://www.burgertuning.com/terms THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS NOT LEGAL FOR USE
More informationBMS JB Stage1 n63/n63tu/s63/s63tu Install Guide
BMS JB Stage1 n63/n63tu/s63/s63tu Install Guide Last updated 6/25/2014 Use subject to terms and conditions posted at http://www.burgertuning.com/terms.htm THIS PART IS LEGAL FOR USE ONLY IN COMPETITION
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationInstallation Manual Lock-Switch KIA Sorento V3 Installation Manual Lock-Switch V3 for KIA Sorento (02-06) and KIA Sorento (07-09)
Installation Manual Lock-Switch V3 for KIA Sorento (02-06) and KIA Sorento (07-09) Note: A any work on the electrical system of a car before should the battery be disconnected at the negative terminal
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationAnother CJ picture guide to
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationBMW E61 fixing tailgate wiring problems
Questo file è stato scaricato da www.bmwretrofit.it @: info@bmwretrofit.it Page: 1 from 10 Postmontaggi - codifiche - ricambi - a Cesena BMW E61 fixing tailgate wiring problems >> DISCLAIMER: this manual
More informationNissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
More informationInstallation Guide. Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands.
Installation Guide Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands. This product is for race use only by experienced engine tuners.
More information2. With the rear door open remove pull-style clip from the passenger side just below the door latch.
LoD Offroad FJ Cruiser Rear Bumper with Tire Carrier Installation Instructions 1. Begin with removing factory spare from the rear door. 2. With the rear door open remove pull-style clip from the passenger
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More informationMY-CUE VIM. Video in Motion for MyLink/CUE NTV-KIT495 BHM 06/28/17 NTV-DOC181
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 MY-CUE VIM Video in Motion for MyLink/CUE NTV-KIT495 BHM Overview The MY-CUE VIM enables video in motion, navigation destination
More informationHow to Install a 997, Boxster, & Cayman Radio
How to Install a 997, Boxster, & Cayman Radio Step-by-step instructions for a 997.1, Boxster, & Cayman Radio Installation. *Credit to CAI- Store.com for this Guide* Written By: Danielle 2017 guides.drivediy.com
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationHeadlight Removal & Installation: VW Jetta Mk.4 / Bora
Headlight Removal & Installation: 99-04 VW Jetta Mk.4 / Bora Disclaimer: Buyer assumes any and all risk and liability from the installation and use of this product. Seller, author, or any of their affiliates
More informationIlluminated Cup Holders Hyundai Elantra (GLS, Limited, Coupe)
Illuminated Cup Holders 2011-2015 Hyundai Elantra (GLS, Limited, Coupe) Thanks for purchasing this Cup Holder Illumination Install Kit! If you have any questions or feedback please email me direct at info@accentglowled.com
More informationSoft Top Rear Locking Cylinders
Soft Top Rear Locking Cylinders Level of difficulty: Fairly easy very rewarding! Tools needed: - M10 socket and ratchet - Flat screwdriver or needle nose pliers or small hooked tool for removal of hydraulic
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012
Installation Tips for your Crimestopper/ProStart Remote Start system (for GM vehicles) v1.01 updated 2/27/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing
More information1 of 2 9/4/ :27 AM
Ford Mustang IAC IAB - Solving your idle problems http://www.muscularmustangs.com/iac.php 1 of 2 9/4/2010 10:27 AM Solving idle problems part 1 - Cleaning your IAC Does your idle rise and fall over and
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationMaserati GranSport Drive by Wire installation
Maserati GranSport Drive by Wire installation Phil Vincenzes MaseratiLife member Vincenzo Email: Phil.Vincenzes@hotmail.com This write-up is not intended in any way to replace the detailed instructions
More informationThis is what we are trying to create in the steps below
You will need: (1) Some 3/4 aluminium or steel flat bar (+/- 1 foot) (2) About 12 of 3 Aluminium or steel tubing. (2) Piece of 3X3 silicone hose and 2 hose clamps (3) 1 K&N (or similar) high flow filter
More informationInstallation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S
Installation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S80 00-09 1. This instruction shows how to replace the OEM radiator with do88 performance radiator. At this type of installation
More informationFree Software with this issue!
The Official Publication of the NATIONAL LOCKSMITH AUTOMOBILE ASSOCIATION 1989 Mercedes Benz 500SEL Free Software with this issue! Part Two by Michael Hyde 12.01 1. This is the second part of a multi-part
More informationSpark Plug replacement on VW 2.0L engine with AEG code
Spark Plug replacement on VW 2.0L engine with AEG code This is document is an attempt to describe and illustrate to some extent the process of replacing the spark plugs on a Volkswagen 2.0L engine with
More informationLED Lighting Upgrade Kit for Tesla Model X Review and Installation Guide [As seen in Teslarati]
LED Lighting Upgrade Kit for Tesla Model X Review and Installation Guide [As seen in Teslarati] Tesla s [factory] Premium Upgrade Package for the Model X and Model S includes what the company describes
More informationRear Speaker replacement.
Rear Speaker replacement. First off you need the right rear speakers. The easy bit is 6x9 and better than a 15W paper cone, the difficult bit is getting a mounting depth under 74mm. Or to be more precise,
More informationSubaru SVX 1/43 Scale Model Assembly Instructions
Subaru SVX 1/43 Scale Model Assembly Instructions Congratulations on your purchase of an unassembled 1/43 scale Subaru SVX! You now own a model that is even more rare than the car it represents. Currently
More informationWritten By: Markus. Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Rollei 6000/6008 Battery LiFePO4 Replacement
Rollei 6000/6008 Battery LiFePO4 Replacement Step-by-Step guide how to replace a dead NICD-Battery with LiFePO-Batteries. Written By: Markus ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION
More informationTIP SHEET T0491. Installation Tips for your Excalibur RS Passlock-sl2(4) + DLRC + SPDT
TIP SHEET T0491 Installation Tips for your Excalibur RS-360 + Passlock-sl2(4) + DLRC + SPDT For Chevrolet: Astro 1998-2005, Avalanche 2002, Blazer 1998-2005, Cavalier 2000-2003, Express Van 1998-2005,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S CIVIC 2 AND 4-DOOR (EX, LX) AII 24188 Issue Date AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationINSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0390C APPLICATION: 1999-2003 E39 M5 PARTS LIST 1 Left Aluminum Intake Tube 1 Air Pump Bracket (A) 1 Right Aluminum Intake Tube 1 Air Pump Bracket
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationDisco 3 Clock Spring / Rotary Coupler replacement
Disco 3 Clock Spring / Rotary Coupler replacement I recently had to change my Clock spring and thought some folks may find it helpful to see what it entailed. I did lots of reading around but couldn t
More informationCurt Mfg. Trailer Hitch and Hoppy Wiring Kit Installation Instructions
Curt Mfg. Trailer Hitch and Hoppy Wiring Kit Installation Instructions The Curt trailer hitch replaces the stock rear cross member in the Touareg. It attaches with 8 bolts just like the factory VW hitch.
More informationBMW 3 Series Oxygen Sensor
1984-1991 BMW 3 Series Oxygen Sensor Replacement Replace an old oxygen sensor on your E30 for better gas mileage. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationZ8 Engine Start Button Install for the BMW E46 3 Series
Z8 Engine Start Button Install for the BMW E46 3 Series This write up is a specific installation of a Z8 engine start button on the E46, but it can be used as a general guide for an engine start button
More informationINSTALLATION INSTRUCTIONS
HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws
More informationSERVICE MANUAL ULTIMATE 200
SERVICE MANUAL ULTIMATE 200 This manual is for: 20 200-120 Ultimate 200 std. 120V 60 Hz 20 200-240 Ultimate 200 std. 240V 50 Hz 20 201-120 Ultimate 200 DMX 120V 60 Hz 20 201-240 Ultimate 200 DMX 240V 50
More information