SPECIFICATION FOR APPROVAL

Size: px

Start display at page:

Download "SPECIFICATION FOR APPROVAL"

Quentin Sullivan
5 years ago
Views:

1 SPECIFICTION FOR PPROVL CUSTOMER NME: DESCRIPTION :. : DESIGNED NO. CUSTOMER PRT NO. ISION. 096 C DPTOR GQ I/P:120VC 60Hz O/P:12VDC 1500m PPROVED BY(PLESE SIGN) Kysan Electronics

2 ENGINEERING CHNGE REQUEST ORIGINL ISION DTE DESCRIPTION ISION OF CUSES DRWER CHECKED PPROVED CUSTOMER DTE PGES 1/10

3 1.ELECTRICL PERFORMNCE 1-1.Primary rated voltage and frequency:120vc 60Hz. 1-2.ELECTRICL CHRCTERISTICS 2 3 IN5401*4 2200uF/25V 5 I/P:120VC 60Hz 1 4 L O D O/P:12VDC 1500m Secondary rated voltage and current TEST POINT Fuse V M33 FULL LOD RTED VOLTGE RTED CURRENT VOLTGE REGULTION NO LOD VOLTGE 5~6 12VDC±5% 1500m 18VDC±5% 1-4.Primary exciting current(lo):60m rms max, at input 120VC 60Hz. Loading(IL):310m rms max. 1-5.D.C.Resistance:Primary:29.36 Ω±15%,measured at Empty loss max:2.5 watts max, at input 120VC 60Hz. 1-7.Temperature rise:75 max on primary coil by the resistance method, and 55 max on the surface of the case by the thermometer method at 25 ambient, rated load condition. 1-8.Insulation resistance:500vdc supplied,100m ohms minimum between winding & core. 1-9.HI-pot test:1250vc 50Hz for 60seconds (leakage current 1m) primary to secondary & core. Potential 20% higher may be applied for one second 500VC 50Hz for 60seconds (leakage current 1m) secondary to ore. Potential 20% higher may be applied for one second DRWER CHECKED PPROVED CUSTOMER DTE PGE 2/10

4 1-10.Induce voltage:ll secondary opened, primary should withstand 240V 360Hz for 60second without breakdown Life test:in an ambient temperature of 25,90-95% R.H., applying a power source of 120VC 60Hz to primary, with full load 1500m for 24hours continuously, unit output normally and meet the requirements of item Humidity test:in an ambient temperature of 25±2 and 90-95% R.H.. for 48 hours after 10 minutes out of the oven, the unit should meet item 1-9 requirements, and insulation Resistance shall be 10M ohms minimum. 2.MECHNICL CHRCTERISTICS 2-1.Drop test:dropped freely from 3 feet height onto a concrete floor covered with 1/8 inch vinyl tile 3 times from 3 different surface, the unit should meet the item Strain relief test:t normal position, 20 lbs to output cord for 60 seconds each, there shall be no breakage displacement. 2-3.Bending test:the plug and S/R should withstand weight of 200 gram, swinging from left to right at an angle of 120 degree for 1000 cycles, and 15-20cycles per minute. The cord shall be conductible. 3.SFETY STNDRD Meet pproved UL/CUL CS TUV/CE BSI/CE T-MRK CQC CCC 4.INSULTION SYSTEM CLSS (105 ) CLSS E(120 ) CLSS B(130 ) CLSS F(155 ) DRWER CHECKED PPROVED CUSTOMER DTE PGES 3/10

5 5.MECHNICL REQUIRMENTS: 5-1.ppearance:Damage and rusting are not permitted. 6.ENVIROMENTL CONDITION: 6-1.Operating temperature range: Storage temperature range: Operation humidity range: % R.H 7.INSPECTION ON LINE: 7-1.The test items for each produce Primary exciting current Core loss Output voltage Input current and power at rated load Foreign mass by shock Polarity of output plug Hi-pot test ppearance 7-2.The test item for part of products: Hum operating at rated load D.C. Resistance Insulation test 8.NET WEIGHT:527g DRWER CHECKED PPROVED CUSTOMER DTE PGES 4/10

6 9.PPERNCE DIMENSION:(UNIT:mm) 17± ± 1 CUTION RISK OF ELECTRIC SHOCK DRY LOCTION USE ONLY 6.3± ± 1 83± / /-0 8.6± ± ± ± ± ± ± 0.3 OUTPUT CORD:UL2464#20WG :1.83m PLUG/DC:5.5 ±0.1mm *2.5 ±0.1mm *9.5 ±0.5mm CENTER: + DRWER CHECKED PPROVED CUSTOMER DTE PGES 5/10

7 10.MTERIL LIST : S P ITEM PRTS NME MTERIL&SPEC MNUFTURER 1. BOBBIN P66 THICK0.71mm MIN E I DUPONT DE NEMOURS&CO INC.E Primary Crossover Insulation CETTE CLOTH TPE CLSS B SUZHOU JINGYI SPECIL DHESIVE TPE CO LTD E PRI.WINDING SEC.WINDING 2UEW MGNET WIRE CLSS B 2UEW 2UEW MGNET WIRE CLSS B 2UEW PCIFIC ELECTRIC WIRE & CBLE CO., LTD E JUNG SHING WIRE CO., LTD.E PRI.OUTER INSULTION SEC.OUTER INSULTION MYLR TPE 0.025mm 0.025mm CLSS B MYLR TPE 0.025mm 0.025mm CLSS B JING JING PRESSURE SENSITIVE GLUE FTY. E SUZHOU JINGYI SPECIL DHESIVE TPE CO.,LTD.E PROTECTION THERML CUTOFF V M33 Jingjiang Xingcheng Electronics Co.,Ltd. TUV LED WIRE UL1015# WG22 SHENZHENDONGJUWIRE&CBLE CO.,LTD.E CORE E-I LMINTED SILICON STEEL BEST LEGEND HUI DINGS LTD RECTIFIER BORD DIODE CPCITOR P.C.BORD(94-V0) CLSS B 94-V0 1.60mm THICK SILICON RECTIFIERS IN5401 ELECTROLYTI 2200uF 25V 13. OUTPUT CORD 2464#20WG 14. NMEPLTE PET(UL/CS)OR LUMINUM KINGBORD LMINTES(MCO COMMERCIL OFFSHORE) LTD.E DONGGUN DE HUI ELECTRONIC CO.,LTD. DONGGUN DE HUI ELECTRONIC CO.,LTD. YUH YIN ELECTRONIC(SHEN ZHEN)CO.,LTD. XIN LONG ENTERPRISE CO.E207567/E DESY WIRE CO.,LTD.E252840/E JING XING PRINTING FCTORY MH45133 SNLI PRINTING FCTORY.MH20917 GUNG NING YOU TONG.MH ENCLOSURE 48UL SBIC INNOVTIVE PLSTICS JPN LLC.E BLDE NICKEL PLTING COPPER2PIN EVERPROUD.LTD NOTE Varnish V821 QULIPOLY CHEMICL CORP.E DRWER CHECKED PPROVED CUSTOMER DTE PGES 6/10

8 11.SMPLE TEST DT: ITEM SPEC SMPLE #1 #2 #3 #4 #5 PRIMRY EXCITING CURRENT I/P:120VC 60Hz 60m MX PRIMRY FULL LOD CURRENT I/P:120VC 60Hz 310m MX SECONDRY VOLTGE NO LOD 18VDC±5% SECONDRY VOLTGE FULL LOD:DC 1500m 12VDC±5% PRI.TO SEC-CORE C 1250V/1m/50Hz/60Seconds OK OK Hi-pot test SEC.TO CORE C 500V/1m/50Hz/60Seconds 交流 500V/1m/50Hz/60 秒 OK OK DRWER CHECKED PPROVED CUSTOMER DTE PGES 7/10

9 12.DC CORD DRWING/DC: Unit:mm / 剥镀 /-0 NOTE: 1.Lead wire:2464wg20#φ0.16/26c 2.Pull force:20lb/1minute of S/R 3.Bending test:weight 200g, ngle 120 Speed 15~20Bends/min 1000Time 4.RoHS Product 9.5± ± ± ± ± 0.1 DRWER CHECKED PPROVED CUSTOMER DTE PGES 8/10

10 13.NMEPLTE DRWING: Unit:mm NOTE: PET 0.27mm THICK MIN DRWER CHECKED PPROVED CUSTOMER DTE PGES 9/10

11 14.PCKING 14-1: OUT BOX SIZE: L:430mm W:315mm H: 175mm *5PCS 100*4PCS SO: PO DES 120VC 60Hz 12VDC 1.5 NUM 40 PCS WEIGHT GROSS SIZE 21 KG 22 KG 420*310*190mm 14-2: WHITE BOX SIZE: L:100mm W:57mm H:70mm DRWER CHECKED PPROVED CUSTOMER DTE PGES 9/10

REV DESCRIPTION DATE

REV DESCRIPTION DATE Specification Page 1 of 9 MODEL NO:EFU120200 CUSTOMER P/N:143722 DESCRIPTION:AC ADAPTOR ISSUED DATE:2012.11.13 REVISION:1-1 TABLE OF CONTENTS 1.0 ELECTRICAL CHARACTERISTIC 2.0 MECHANICAL PERFORMANCE 3.0