2013 Kia Optima L4-2.0L Turbo

Size: px
Start display at page:

Download "2013 Kia Optima L4-2.0L Turbo"

Transcription

1 1 of 13 5/29/ :34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted surfaces. To avoid damage, unplug the wiring connectors carefully while holding the connector portion. NOTE: Mark all wiring and hoses to avoid misconnection. To release the fuel system pressure before removing the engine assembly, start the engine with the fuel pump relay removed. And then turn off the ignition switch after engine stops. 1. Remove the engine cover. 2. Disconnect the battery terminals (A). Tightening torque : (+) terminal : N.m ( kgf.m, lb-ft) (-) terminal : N.m ( kgf.m, lb-ft) 3. Remove the air duct (B). 4. Remove the battery (A) after removing the mounting bracket (B) N.m ( kgf.m, lb-ft)

2 2 of 13 5/29/ :34 AM 5. Remove the air cleaner assembly. (1) Disconnect the breather hose (A), the recirculation hose (B) and the brake booster vacuum hose (C). (2) Disconnect the air intake hose (D) and then remove the air cleaner assembly (E). Tightening torque Hose clamp bolt: N.m ( kgf.m, lb-ft) Air cleaner assembly bolts: N.m ( kgf.m, lb-ft) 6. Remove the battery tray (A) N.m ( kgf.m, lb-ft)

3 3 of 13 5/29/ :34 AM 7. Remove the intercooler inlet hose (A) N.m ( kgf.m, lb-ft) 8. Disconnect the recirculation valve connector (A) and the vacuum hose (B), and then remove the intercooler inlet pipe & hose assembly (C) Tightening torque Pipe mounting bolt: N.m ( kgf.m, lb-ft)

4 4 of 13 5/29/ :34 AM 9. Disconnect the boost pressure sensor connector (A) and then remove the intercooler outlet pipe & hose assembly (B). Tightening torque N.m ( kgf.m, lb-ft) 10. Remove the under covers (A,B) N.m ( kgf.m, lb-ft)

5 5 of 13 5/29/ :34 AM NOTE: When removing the under cover (B), unfasten the mounting bracket bolts and then remove the under cover and mounting bracket assembly. 11. Loosen the drain plug, and drain the engine coolant. Remove the radiator cap to drain with speed. 12. Disconnect the radiator upper hose (A) and lower hose (B). 13. Recover the refrigerant and then remove the high pressure pipe and low pressure pipe (A).

6 6 of 13 5/29/ :34 AM 14. Disconnect the (+) cable (A) from the fuse/relay box and the front connector (B). Then remove the wiring protector (C). 15. Disconnect the ECM connectors (A) from the ECM, the fuse box connector (B) from the fuse/relay box and the engine ground line (C). Then remove the wiring protector (D). 16. Remove the transaxle wire harness connectors (A) and control cable (B) from the transaxle..

7 7 of 13 5/29/ :34 AM 17. Disconnect the ATF cooler hoses (A). 18. Disconnect the intensifier hose (A) and the vacuum hose (B). 19. Disconnect the fuel hose (A) and PCSV (Purge control solenoid valve) hose (B).

8 8 of 13 5/29/ :34 AM 20. Disconnect the heater hoses (A). 21. Remove the front muffler (B) after disconnecting the front oxygen sensor connector (A) N.m ( kgf.m, lb-ft)

9 9 of 13 5/29/ :34 AM 22. Remove the steering u-joint mounting bolt (A). 23. Remove the front wheels. 24. Remove the lower arms (A). 25. Remove the stabilizer bar links (A).

10 10 of 13 5/29/ :34 AM 26. Remove the tie rod ends (A). 27. Disconnect the drive shafts from the axle hubs. 28. Remove the roll rod bracket (A). Nut (B): N.m ( kgf.m, lb-ft) Bolt (C): N.m ( kgf.m, lb-ft)

11 11 of 13 5/29/ :34 AM 29. Support the sub frame (A) with a floor jack, and then remove the sub frame mounting bolts and nuts. Sub frame mounting bolts & nuts : N.m ( kgf.m, lb-ft) Stay mounting bolts : N.m ( kgf.m, lb-ft) NOTE: After removing the sub frame mounting bolt, the engine and transaxle assembly may fall downward, and so support them securely with floor jack. Verify that the hoses and connectors are disconnected before removing the engine and transaxle assembly. 30. Disconnect the ground line (A), and then remove the engine mounting support bracket (B) N.m ( kgf.m, lb-ft) 31. Disconnect the ground line (A), and then remove the transaxle mounting support bracket (B).

12 12 of 13 5/29/ :34 AM N.m ( kgf.m, lb-ft) 32. Remove the engine and transaxle assembly by lifting vehicle. CAUTION: When remove the engine and transaxle assembly, be careful not to damage any surrounding parts or body components. Installation Installation is in the reverse order of removal. Perform the following : Adjust a shift cable. Refill engine with engine oil. Refill a transaxle with fluid. Refill a radiator and a reservoir tank with engine coolant. Clean battery posts and cable terminals and assemble. Inspect for fuel leakage. After assemble the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.

13 13 of 13 5/29/ :34 AM Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line. Bleed air from the cooling system. Start engine and let it run until it warms up. (until the radiator fan operates 3 or 4 times.) Turn Off the engine. Check the level in the radiator, add coolant if needed. This will allow trapped air to be removed from the cooling system. Put radiator cap on tightly, then run the engine again and check for leaks.

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

Cylinder Head Assembly: Removal and Replacement Repair Procedures

Cylinder Head Assembly: Removal and Replacement Repair Procedures 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Cylinder Head Assembly: Removal and Replacement Repair Procedures COMPONENT 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 2 REMOVAL Engine

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

Power Steering Pump. GM Century/Lumina/Grand Prix/Intrigue REMOVAL & INSTALLATION BLEEDING

Power Steering Pump. GM Century/Lumina/Grand Prix/Intrigue REMOVAL & INSTALLATION BLEEDING 1 of 9 GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Power Steering Pump REMOVAL & INSTALLATION BLEEDING When servicing the power steering pump, inspect the power steering fluid. Look for foaming, milky

More information

2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required

2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required 2004 Honda ELEMENT Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS Engine Installation Special Tools Required Engine hanger/adapter VSB02C000015 Engine support hanger, A & Reds AAR-T-12566

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

Cylinder Head Removal

Cylinder Head Removal 2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors

More information

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation. 1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

Engine Removal/lnstaIlation

Engine Removal/lnstaIlation Engine Removal/lnstaIlation Removal Make sure jacks and safety stands are placed properly and hoist brackets are attached to the correct positions on the engine. Make sure the vehicle will not roll off

More information

9. Engine Assembly ENGINE ASSEMBLY

9. Engine Assembly ENGINE ASSEMBLY 9. Engine Assembly A: REMOVAL 1) Set the vehicle on a lift. 2) Open the front hood fully, and then support with the hood stay. 3) Collect the refrigerant from A/C system. 4) Release the fuel pressure.

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate

More information

INTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS...

INTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS... 15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL DESCRIPTION 15-2 SERVICE SPECIFICATIONS 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3

More information

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

INTAKE AND EXHAUST GROUP CONTENTS INTERCOOLER GENERAL INFORMATION SERVICE SPECIFICATIONS

INTAKE AND EXHAUST GROUP CONTENTS INTERCOOLER GENERAL INFORMATION SERVICE SPECIFICATIONS 15-1 GROUP 15 ITAKE AD EXHAUST COTETS GEERAL IFORMATIO........ 15-2 SERVICE SPECIFICATIOS....... 15-2 SPECIAL TOOL................. 15-2 O-VEHICLE SERVICE........... 15-3 ITERCOOLER WATER SPRAY RELAY CHECK............................

More information

16A. STARTING - CHARGING Starter: Removal - Refitting REFITTING 16A-11 K4M II - REMOVAL OPERATION III - FINAL OPERATION

16A. STARTING - CHARGING Starter: Removal - Refitting REFITTING 16A-11 K4M II - REMOVAL OPERATION III - FINAL OPERATION STARTING - CHARGING Starter: Removal - Refitting 16A K4M II - REMOVAL OPERATION III - FINAL OPERATION JR5 a Clip: -the gearbox control cable sleeve stops on the gearbox, - the control cables onto the gearbox.

More information

INTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER

INTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER 15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL INFORMATION 15-2 SERVICE SPECIFICATION 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3 SPECIAL

More information

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove 1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B 5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal

More information

ENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT

ENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT 14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE

More information

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release

More information

BUZZERS, RELAYS & TIMERS

BUZZERS, RELAYS & TIMERS BUZZERS, RELAYS & TIMERS 1997 MAZDA MX-5 Miata BUZZERS, RELAYS & TIMERS Location A/C Relay In right front of engine compartment, near radiator. See Fig. 1. Condenser Fan Relay In right front of engine

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

1. Remove the battery tray. For additional information, refer to Battery Tray ( )

1. Remove the battery tray. For additional information, refer to Battery Tray ( ) Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

FUEL SUPPLY Click on the applicable bookmark to selected the required model year

FUEL SUPPLY Click on the applicable bookmark to selected the required model year FUEL SUPPLY F- FUEL SUPPLY CONTENTS 0000 GENERAL INFORMATION................ FUEL TANK............................. FUEL FILTER ......................................... 6 F- FUEL

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace. EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER

More information

5. Engine Control Module (ECM) I/O Signal S008526

5. Engine Control Module (ECM) I/O Signal S008526 5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen

More information

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing

More information

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane Engine Remove and Install ( 34 0) Special Tools 068 A 068A Engine lifting tackle 4 003 Coolant hose clamp removal and fitting tool Workshop Equipment Transmission jack Trolley jack Workshop crane Materials

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. Engine Control Module (ECM) I/O Signal A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9

More information

ELECTRICAL COMPONENT LOCATOR

ELECTRICAL COMPONENT LOCATOR ELECTRICAL COMPONENT LOCATOR 1988 Toyota Celica 1988 TOYOTA Celica Electrical Components ---------------------------------------------------------------------- BUZZERS, RELAYS & TIMERS ----------------------------------------------------------------------

More information

EVAP system, servicing

EVAP system, servicing Page 1 of 65 20-130 EVAP system, servicing EVAP system components 1 - Cap nut 10 Nm 2 - Cover 3 - Stud For EVAP canister 15 Nm 4 - Sealing piece 5 - Bleed line To EVAP canister purge regulator valve -

More information

Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

RADIATOR CLEANING OF RADIATOR

RADIATOR CLEANING OF RADIATOR CO20 COOLING SYSTEM RADIATOR CLEANING OF RADIATOR Using water or a steam cleaner, remove any mud and dirt from the radiator core. CAUTION: If using a high pressure type cleaner, be careful not to deform

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

BUZZERS, RELAYS & TIMERS

BUZZERS, RELAYS & TIMERS ELECTRICAL COMPONENT LOCATOR 1994 ELECTRICAL COMPONENT LOCATION Mazda Electrical s BUZZERS, RELAYS & TIMERS BUZZERS, RELAYS & TIMERS LOCATION ABS s Motor Relay On top of ABS pump, on right rear corner

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31

More information

ENGINE REMOVAL Honda Accord EX. Special Tools Required

ENGINE REMOVAL Honda Accord EX. Special Tools Required ENGINE REMOVAL Special Tools Required 2008 V6 Attachment Arm SIL02C000033* Engine Support Hanger, A and Reds AAR-T1256* Engine Hanger Balance Bar VSB02C000019* Subframe Adapter VSB02C000016* *Available

More information

Body, front. Lock carrier with attachments, removing and installing

Body, front. Lock carrier with attachments, removing and installing Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)

More information

2002 Jeep Grand Cherokee Laredo

2002 Jeep Grand Cherokee Laredo Removal WARNING: DO NOT REMOVE THE CYLINDER BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR. REFER TO COOLING SYSTEM DRAINING.

More information

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage

More information

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD)

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY

More information

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl...

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl... Page 1 of 7 VELOSTER(FS) >2013 > G 1.6 T-GDI > Engine Mechanical System > General Information > Specifications Specifications General Type Description Specifications Except Europe In-line, DOHC Number

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)

More information

ARTICLE BEGINNING SAFETY PRECAUTION BUZZERS, RELAYS & TIMERS ELECTRICAL COMPONENT LOCATION Volkswagen Electrical Components - 2.0L 4-Cyl.

ARTICLE BEGINNING SAFETY PRECAUTION BUZZERS, RELAYS & TIMERS ELECTRICAL COMPONENT LOCATION Volkswagen Electrical Components - 2.0L 4-Cyl. Article Text ARTICLE BEGINNING 1996 ELECTRICAL COMPONENT LOCATION Volkswagen Electrical Components - 2.0L 4-Cyl. Cabrio, Golf III, Jetta III SAFETY PRECAUTION WARNING: When working on vehicles equipped

More information

1 of 13 10/12/2013 2:20 PM

1 of 13 10/12/2013 2:20 PM 1 of 13 10/12/2013 2:20 PM Coolant Pump, 4-cyl. Warning: Take care if the car is warm. The coolant is hot and there is also a risk of burning yourself on the manifold. To Remove 1. Open the cap on the

More information

2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing

2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing 1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement

More information

Technical Service Bulletin

Technical Service Bulletin Technical Service Bulletin SUBJECT: GROUP DATE NUMBER CAMPAIGN 17-01-045 JUNE, 2017 MODEL SONATA HYBRID (LF HEV) HYBRID STARTER GENERATOR (HSG) INSPECTION / REPLACEMENT (Service Campaign T2E) IMPORTANT

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

ENGINE COOLING FAN Toyota Celica ELECTRIC COOLING FAN RADIATOR COOLING FAN SYSTEM TEST ENGINE COOLING Toyota Engine Cooling Fans

ENGINE COOLING FAN Toyota Celica ELECTRIC COOLING FAN RADIATOR COOLING FAN SYSTEM TEST ENGINE COOLING Toyota Engine Cooling Fans ENGINE COOLING FAN 1994 Toyota Celica 1994 ENGINE COOLING Toyota Engine Cooling Fans Celica 1.8L 4-Cyl ELECTRIC COOLING FAN NOTE: Electric cooling fan may be used for radiator or condenser. To verify electric

More information

INTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...

INTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER... I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

Engine Removal and Installation

Engine Removal and Installation Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle

More information

ENGINE COOLING Click on the applicable bookmark to selected the required model year

ENGINE COOLING Click on the applicable bookmark to selected the required model year ENGINE COOLING - ENGINE COOLING General Information/ Service Specifications/Lubricant/Sealants GENERAL INFORMATION 0000 The cooling system is designed to keep every part of the engine at appropriate temperature

More information

INTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose

INTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose INTAKE MANIFOLD COLLECTOR Removal and Installation PFP:14003 ABS0095V 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose 4. EVAP canister purge volume control solenoid valve 5. Bracket 6. Intake

More information

2003 RSX - Intake Manifold Removal and Installation

2003 RSX - Intake Manifold Removal and Installation 2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» LH Valve Cover LH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner

More information

Cylinder head/gasket, replacing

Cylinder head/gasket, replacing 1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations

More information

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of

More information

PART - RETAIL SHOP C900 DAVID'S [78-94] 9000 PRICE [84-98] LIST NG900 [94-98] OG9-3 [99-03] 9-3SS [03-11] A/C Compressor

PART - RETAIL SHOP C900 DAVID'S [78-94] 9000 PRICE [84-98] LIST NG900 [94-98] OG9-3 [99-03] 9-3SS [03-11] A/C Compressor PART - RETAIL SHOP C900 DAVID'S [78-94] 9000 PRICE [84-98] LIST NG900 [94-98] OG9-3 [99-03] 9-3SS [03-11] A/C Compressor 150-250 150-250 150-250 150-250 150-250 A/C Condensor A/C Miscellaneous Parts A/C

More information

Page 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C

More information

INTAKE AND EXHAUST GROUP 15 CONTENTS GENERAL INFORMATION INTERCOOLER SERVICE SPECIFICATIONS INLET MANIFOLD...

INTAKE AND EXHAUST GROUP 15 CONTENTS GENERAL INFORMATION INTERCOOLER SERVICE SPECIFICATIONS INLET MANIFOLD... GROUP 1 ITAKE AD EXHAUST COTETS GEERAL IFORMATIO........ 1-2 SERVICE SPECIFICATIOS....... 1-2 SPECIAL TOOL................. 1-2 O-VEHICLE SERVICE........... 1-3 TURBOCHARGER SUPERCHARGIG PRESSURE CHECK

More information

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to

More information

2000 Chrysler SEBRING

2000 Chrysler SEBRING 2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a

More information

Service Bulletin MIL Comes On With DTCs P0300 Thru P0306 (Supersedes , dated June 5, 2013; see REVISION SUMMARY) August 23, 2013

Service Bulletin MIL Comes On With DTCs P0300 Thru P0306 (Supersedes , dated June 5, 2013; see REVISION SUMMARY) August 23, 2013 Service Bulletin 13-024 Applies To: 2013 MDX From VIN 2HNYD2...DH500001 thru 2HNYD2...DH525406 2013 TL SH-AWD From VIN 19UUA9...DA000001 thru 19UUA9...DA005530 2013 ZDX From VIN 2YNYB1...DH500001 thru

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

Included parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe

Included parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports

More information

ENGINE AND EMISSION CONTROL

ENGINE AND EMISSION CONTROL 17-1 ENGINE AND EMISSION CONTROL CONTENTS EMISSION CONTROL SYSTEM... 2 GENERAL... 2 Outline of Changes... 2 GENERAL INFORMATION... 2 SERVICE SPECIFICATION... 2 VACUUM HOSE... 3 Vacuum Hose Piping Diagram...

More information

1991 TOYOTA Electrical Components MR2. evaporator. compartment. ARTICLE BEGINNING BUZZERS, RELAYS & TIMERS

1991 TOYOTA Electrical Components MR2. evaporator. compartment. ARTICLE BEGINNING BUZZERS, RELAYS & TIMERS ELECTRICAL COMPONENT LOCATOR Article Text ARTICLE BEGINNING 1991 TOYOTA Electrical Components MR2 BUZZERS, RELAYS & TIMERS A/C Compressor Clutch Relay Under right side of dash, on evaporator. Circuit Opening

More information

1 of 15 C:\Users\sny\Downloads\2019 Used Parts Price List.ods

1 of 15 C:\Users\sny\Downloads\2019 Used Parts Price List.ods PART - RETAIL SHOP C900 DAVID'S [78-94] 9000 PRICE [84-98] LIST NG900 [94-98] OG9-3 [99-03] 9-3SS [03-11] A/C Compressor 150-250 150-250 150-250 150-250 150-250 A/C Condensor A/C Miscellaneous Parts A/C

More information

Installation Instructions

Installation Instructions Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor

More information

Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity

Radiator Service Tool Set Hexagon Wrench Set TOYOTA Electrical Tester Set. Capacity ENGINE EG329 PREPARATION SST (SPECIAL SERVICE TOOLS) 0923001010 Radiator Service Tool Set 0923114010 Punch 2JZGE only (Aluminum type) RECOMMENDED TOOLS 0904000010 Hexagon Wrench Set 0908200050 TOYOTA Electrical

More information

2003 ACCORD - Intake Manifold Removal and Installation

2003 ACCORD - Intake Manifold Removal and Installation 2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose

More information

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter 1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower

More information

TURBOCHARGER ON VEHICLE INSPECTION TC 7

TURBOCHARGER ON VEHICLE INSPECTION TC 7 TC7 ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR SYSTEM Check for leakage or clogging between the air cleaner and turbocharger inlet and between the turbocharger outlet and cylinder head. Clogged air cleaner...

More information

Supercharged MK1 MR2 Part Diagrams

Supercharged MK1 MR2 Part Diagrams Supercharged MK1 MR2 Part Diagrams Created by: Charles K. (ckowalc) 1 Table of Contents PART DIAGRAM PAGE ACCELERATOR LINK 9 AIR CLEANER 10 AIR CLEANER 4AGZE 11 ALTERNATOR 4AGZE 12 ANTENNA 13 ARMREST &

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

Page 1 of 10 43: Transmission, automatic, B5254T2, AW50/51 AWD V70 XC (01-) / XC70 (-07), 2004, B5254T2, AW50/51 AWD, L.H.D, YV1SZ59H241147306, 147306 15/10/2011 PRINT 43: Transmission, automatic, B5254T2,

More information

TURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models

TURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached

More information

Intake Manifold Removal and Installation

Intake Manifold Removal and Installation 2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum

More information

Drawing Page Drawing Page

Drawing Page Drawing Page Contents Drawing Page Drawing Page L4 Engine...1 L4 Engine - Exploded View...2 V6 Engine...3 V6 Engine - Exploded View... 4 Oil Filter...5 VTEC (Variable Timing Electronic Control) System... 6 Fuel and

More information

2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX

2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX 2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE 2 SECTION FU(SOHCw/oOBD) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) EXHAUST EC(SOHCw/oOBD) EX(SOHCw/oOBD) This service manual has been prepared

More information

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove 1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable.

More information

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT

1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT 1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

GROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS...

GROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS... 14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOL 14-2 ENGINE COOLING DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE

More information

Installation Instructions

Installation Instructions Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI

More information