INTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose
|
|
- Joel Norton
- 6 years ago
- Views:
Transcription
1 INTAKE MANIFOLD COLLECTOR Removal and Installation PFP:14003 ABS0095V 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose 4. EVAP canister purge volume control solenoid valve 5. Bracket 6. Intake manifold collector (upper) 7. Intake manifold collector cover 8. Gasket 9. Water hose 10. Bracket 11. Water hose 12. PCV hose 13. Intake manifold collector (lower) REMOVAL WARNING: PBIC2081E To avoid the danger of being scalded, do not drain the engine coolant when the engine is hot. Gasket for intake manifold collector (upper) is secured together with mounting bolt for intake manifold collector (lower). Thus, even when only gasket for upper side is replaced, gasket for lower side must be also replaced. EM-18
2 1. Remove engine cover with power tool. A EM C D E F KBIA0956E 2. Drain engine coolant, or when water hose is disconnected, attach plug to prevent engine coolant leakage. Refer to CO-10, "Changing Engine Coolant". CAUTION: Perform this step when engine is cold. Do not spill engine coolant on drive belts. 3. Remove air cleaner case and air duct. Refer to EM-16, "AIR CLEANER AND AIR DUCT". 4. Remove electric throttle control actuator as follows: a. Disconnect harness connector. b. Loosen bolts in reverse order as shown in the figure. CAUTION: Handle carefully to avoid any shock to electric throttle control actuator. Do not disassemble. G H I J K L M KBIA0957E 5. Remove fuel sub-tube mounting bolt to disconnect from rear of intake manifold collector (lower). Refer to EM-38, "FUEL INJECTOR AND FUEL TUBE". 6. Disconnect vacuum hose and water hose from intake manifold collector (upper). 7. Remove EVAP canister purge volume control solenoid valve bracket mounting bolt from intake manifold collector (upper). EM-19
3 8. Loosen bolts in reverse order as shown in the figure to remove intake manifold collector (upper) with power tool. PBIC0773E 9. Remove PCV hose [between intake manifold collector (lower) and rocker cover (right bank)]. 10. Loosen bolts in reverse order as shown in the figure, and remove the intake manifold collector cover, gasket, intake manifold collector (lower) and gasket with power tool. INSPECTION AFTER REMOVAL Surface Distortion Check the surface distortion of both the intake manifold collector (upper and lower) mating surfaces with straightedge and feeler gauge. Limit : 0.1 mm (0.004 in) If it exceeds the limit, replace intake manifold collector (upper and/or lower). PBIC0774E PBIC0775E EM-20
4 INSTALLATION Note the following, and install in the reverse order of removal. Indication of Part Installation Direction Referring to front marks, install parts shown in the figure. A EM C D E F G Intake Manifold Collector (Lower) Tighten in numerical order as shown in the figure. NOTE: Tighten mounting bolts to secure gasket (lower), intake manifold collector (lower), gasket (upper), and intake manifold collector cover. PBIC0776E H I J K Intake Manifold Collector (Upper) If stud bolts were removed, install them and tighten to the torque specified below. Shank length under bolt head varies with bolt location. Install bolts while referring to numbers shown below and in the figure. (Bolt length does not include pilot portion.) Tighten in numerical order as shown in the figure. Water Hose : N m ( kg-m, in-lb) Bolt M6 25 mm (0.98 in) : 7, 8, 10, 11, 13, 14, 15, 16, 18 M6 45 mm (1.77 in) : 2, 4, 5 M6 60 mm (2.36 in) : 1, 3, 6, 9 M6 Nut : 12, 17 Insert hose by 27 to 32 mm (1.06 to 1.26 in) from connector end. PBIC0774E PBIC0773E L M EM-21
5 Clamp hose at location of 3 to 7 mm (0.12 to 0.28 in) from hose end. Electric Throttle Control Actuator Install gasket with three protrusions for installation check facing any direction other than upward. Tighten in numerical order as shown in the figure. Perform the Throttle Valve Closed Position Learning when harness connector of electric throttle control actuator is disconnected. Refer to EC-42, "Throttle Valve Closed Position Learning". Perform the Idle Air Volume Learning and Throttle Valve Closed Position Learning when electric throttle control actuator is replaced. Refer to EC-42, "Idle Air Volume Learning". KBIA0957E EM-22
ENGINE LUBRICATION SYSTEM
ENGINE LUBRICATION SYSTEM B ENGINE A SECTION ENGINE LUBRICATION SYSTEM LU C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION... 3 Special
More informationSTARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
More informationENGINE MECHANICAL SECTION CONTENTS B ENGINE EM-1
ENGINE MECHANICAL B ENGINE A SECTION ENGINE MECHANICAL EM C D CONTENTS E PRECAUTIONS... 3 Precautions for Draining Engine Coolant... 3 Precautions for Disconnecting Fuel Piping... 3 Precautions for Removal
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More informationENGINE MECHANICAL SECTION EM CONTENTS B ENGINE EM-1
ENGINE MECHANICAL B ENGINE SECTION EM A ENGINE MECHANICAL EM C D CONTENTS E PRECAUTIONS... 3 Precautions for Drain Engine Coolant... 3 Precautions for Disconnecting Fuel Piping... 3 Precautions for Removal
More informationENGINE MECHANICAL SECTION EM CONTENTS B ENGINE EM-1
ENGINE MECHANICAL B ENGINE SECTION EM A ENGINE MECHANICAL EM C D CONTENTS E PRECAUTIONS... 3 Precautions for Battery Service... 3 Precautions for Draining Engine Coolant... 3 Precautions for Disconnecting
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationENGINE MECHANICAL SECTION EM CONTENTS B ENGINE EM-1
ENGINE MECHANICAL B ENGINE SECTION EM A ENGINE MECHANICAL EM C D CONTENTS E PRECAUTIONS... 3 Precautions for Drain Engine Coolant and Engine Oil... 3 Precautions for Disconnecting Fuel Piping... 3 Precautions
More informationENGINE MECHANICAL SECTION EM CONTENTS B ENGINE EM-1
B ENGINE SECTION EM A ENGINE MECHANICAL EM C D CONTENTS E PRECAUTIONS... 3 Precautions for Drain Engine Coolant... 3 Precautions for Disconnecting Fuel Piping... 3 Precautions for Removal and Disassembly...
More information2003 ACCORD - Intake Manifold Removal and Installation
2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose
More informationIntake Manifold Removal and Installation
2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More informationFUEL PRESSURE REGULATOR
EG2214 3VZE ENGINE FUEL PRESSURE REGULATOR ONVEHICLE INSPECTION CHECK FUEL PRESSURE (See step 2 on page EG2206) COMPONENTS FOR REMOVAL AND INSTALLATION FUEL PRESSURE REGULATOR REMOVAL 1. DISCONNECT NEGATIVE
More informationENGINE LUBRICATION SYSTEM
B ENGINE A SECTION ENGINE LUBRICATION SYSTEM LU C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION... 3 Special Service Tools... 3 Commercial
More information2003 RSX - Intake Manifold Removal and Installation
2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationENGINE LUBRICATION SYSTEM
ENGINE LUBRICATION SYSTEM B ENGINE SECTION LU A ENGINE LUBRICATION SYSTEM LU C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION
More informationENGINE LUBRICATION SYSTEM
ENGINE LUBRICATION SYSTEM B ENGINE SECTION LU A ENGINE LUBRICATION SYSTEM LU C D CONTENTS E QR PRECAUTIONS... 3 Precautions for Liquid Gasket... 3 LIQUID GASKET APPLICATION PROCEDURE... 3 PREPARATION...
More informationALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair
ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationENGINE LUBRICATION SYSTEM
ENGINE LUBRICATION SYSTEM B ENGINE A SECTION ENGINE LUBRICATION SYSTEM LU C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION... 3 Special
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationENGINE AND EMISSION CONTROL
17-1 ENGINE AND EMISSION CONTROL CONTENTS EMISSION CONTROL SYSTEM... 2 GENERAL... 2 Outline of Changes... 2 GENERAL INFORMATION... 2 SERVICE SPECIFICATION... 2 VACUUM HOSE... 3 Vacuum Hose Piping Diagram...
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationENGINE LUBRICATION SYSTEM
B ENGINE SECTION LU A ENGINE LUBRICATION SYSTEM LU C D CONTENTS E QR25DE PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE...
More informationENGINE LUBRICATION SYSTEM
B ENGINE SECTION LU A ENGINE LUBRICATION SYSTEM LU C D CONTENTS E QR25DE PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION...
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationREMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More informationINTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS...
15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL DESCRIPTION 15-2 SERVICE SPECIFICATIONS 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3
More information2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section
Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to
More information2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716
More informationDISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)
2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More informationEG1 361 THROTTLE BODY
3SGTE ENGINE EG1361 THROTTLE BODY EG1362 3SGTE ENGINE ONVEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port. Start the engine.
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationSECTION CONTENTS ENGINE EM-1 QG18DE
B ENGINE A SECTION ENGINE MECHANICAL EM C D CONTENTS E QG18DE PRECAUTIONS... 4 Parts Requiring Angular Tightening... 4 Liquid Gasket Application Procedure... 4 PREPARATION... 5 Special Service Tools...
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationAudi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
More informationREMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)
EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop
More information10/6/2017 Engine mechanical > Qr25de > Removal and installation > Timing chain 2012 Nissan Frontier MotoLogic
2012 Frontier Report a problem with this article https://www.motologic.com/car/bcccc3df2606263be9c3e41bf785b881/article/a61013ad842ec2ab361f2c98cf9f0577h24?returnpath=%2fcar%2fbccc 1/10 TIMING CHAIN Exploded
More informationENGINE MECHANICAL SECTION CONTENTS B ENGINE EM-1 KA24DE
ENGINE MECHANICA B ENGINE A SECTION ENGINE MECHANICA EM C D KA24DE PRECAUTIONS... 5 Precautions for Drain Coolant... 5 Precautions for Disconnecting Fuel Piping... 5 Precautions for Removal and Disassembly...
More informationINTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...
I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More information2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE SECTION 1 FU(H4SO) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) INTAKE (INDUCTION) EC(H4SO) IN(H4SO) This service manual has been prepared to
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More information1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationINTAKE AND EXHAUST GROUP 15 CONTENTS GENERAL INFORMATION INTERCOOLER SERVICE SPECIFICATIONS INLET MANIFOLD...
GROUP 1 ITAKE AD EXHAUST COTETS GEERAL IFORMATIO........ 1-2 SERVICE SPECIFICATIOS....... 1-2 SPECIAL TOOL................. 1-2 O-VEHICLE SERVICE........... 1-3 TURBOCHARGER SUPERCHARGIG PRESSURE CHECK
More informationTIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
More information2000 Chrysler SEBRING
2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More information2001 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX
2001 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX SUPPLEMENT FOR 6 CYLINDER ENGINE MODEL This service manual has been prepared to provide SUBARU service personnel with the necessary information and data
More informationINTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER
15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL INFORMATION 15-2 SERVICE SPECIFICATION 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3 SPECIAL
More informationSECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1 SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) WARNING: For vehicles equipped with Supplemental Restraint (Air Bag) System: Service on and
More information7. Evaporative Emission Control System
W1860BE.book Page 10 Tuesday, January 28, 2003 11:01 PM 7. Evaporative Emission Control System A: GENERAL The evaporative emission control system prevents fuel vapors from escaping into atmosphere. This
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More information2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body.
2002 Silverado K 4WD Applies to: 4.8L, 5.3L, and 6.0L Report a problem with this article Removal Procedure 1. Remove the air intake duct. Refer to Air Cleaner Resonator Outlet Duct Replacement. 2. Disconnect
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationSpecial tools required:
11 12 100 Removing and installing/sealing cylinder head (S54) Special tools required: 11 4 400 12 1 120 Remove both exhaust manifolds. Remove intake filter housing with air-mass flow sensor. Remove cylinder
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationENGINE AND EMISSION CONTROL
17-1 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL SYSTEM........ 3 SERVICE SPECIFICATION............... 3 ON-VEHICLE SERVICE.................. 3 Accelerator Cable Check and Adjustment... 3 ACCELERATOR
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationEMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission
More informationENGINE MECHANICAL SECTIONEM CONTENTS IDX QG18DE
ENGINE MECHANICAL SECTIONEM GI MA LC EC CONTENTS FE QG18DE PRECAUTIONS...4 Parts Requiring Angular Tightening...4 Liquid Gasket Application Procedure...4 PREPARATION...5 Special Service Tools...5 Commercial
More information2002 Mustang Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)
More informationEMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission
More informationINTAKE AND EXHAUST GROUP CONTENTS INTERCOOLER GENERAL INFORMATION SERVICE SPECIFICATIONS
15-1 GROUP 15 ITAKE AD EXHAUST COTETS GEERAL IFORMATIO........ 15-2 SERVICE SPECIFICATIOS....... 15-2 SPECIAL TOOL................. 15-2 O-VEHICLE SERVICE........... 15-3 ITERCOOLER WATER SPRAY RELAY CHECK............................
More informationReproduction. Not for. Illustrated Parts List 49E700. Model Series TYPE NUMBERS FORM MS /17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700
FORM MS10562 10/17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700 Illustrated Parts List Model Series 49E700 TYPE NUMBERS 0001. PRINTED IN U.S.A. COPYRIGHT by BRIGGS & STRATTON CORPORATION All rights reserved.
More information2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE 2 SECTION FU(SOHCw/oOBD) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) EXHAUST EC(SOHCw/oOBD) EX(SOHCw/oOBD) This service manual has been prepared
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationINTAKE (INDUCTION) IN(TURBO)
IN(TURBO) Page 1. General Description...2 2. Air Cleaner...7 3. Air Intake Duct...8 4. Intake Duct...9 5. Intercooler...10 6. Turbocharger...12 7. Air By-pass Valve...14 8. Resonator Chamber...15 GENERAL
More informationEG2 173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM
5SFE ENGINE EG2173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM EG2174 5SFE ENGINE EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 9 SECTION 303-04: Fuel Charging and Controls 2002 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/13/2001 Fuel Injection Supply Manifold Material
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More informationENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-1 SECTION 6A1 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) WARNING: For vehicles equipped with Supplement Restraint (Air Bag) System: Service on
More informationVehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair. Service and Repair
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Suzuki Verona L6-2.5L Conversion Calculator Vehicle
More informationREMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
More informationON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
More informationENGINE MECHANICAL SECTIONEM CONTENTS IDX
ENGINE MECHANICAL SECTIONEM GI MA LC EC CONTENTS FE CL PRECAUTIONS...3 Parts Requiring Angular Tightening...3 Liquid Gasket Application Procedure...3 PREPARATION...4 Special Service Tools...4 Commercial
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationENGINE MECHANICAL SECTIONEM CONTENTS IDX
ENGINE MECHANICAL SECTIONEM GI MA LC CONTENTS EC FE PRECAUTIONS...3 Parts Requiring Angular Tightening...3 Liquid Gasket Application Procedure...3 PREPARATION...4 Special Service Tools...4 Commercial Service
More informationOn Board Diagnostics II A PCED
Page 1 of 5 1998 PCED On Board Diagnostics II A SECTION 5A: Pinpoint Tests KE: Idle Air Control (IAC) Valve KE: Introduction KE1 IDLE CONCERNS OR STALLS: RUN KOER SELF-TEST AND OUTPUT CONTINUOUS MEMORY
More information1.6L 4-CYL - VIN [E]
1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
More information