Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Spark Plug Wire Remover T74P-6666-A EFI/CFI Fuel Pressure Gauge T80L-9974-B 1. Disconnect the negative battery cable. For additional information, refer to Section Drain the cooling system. For additional information, refer to Section Drain and evacuate the A/C system. For additional information, refer to Section Remove the air inlet tubes. Disconnect the air by-pass hose and remove the crankcase vent hose. 5. Loosen the fan-to-water pump bolts. Loosen the alternator adjusting bolts and remove the alternator belt. Rotate the drive belt tensioner counterclockwise and remove the A/C drive belt. For additional information, refer to Section Remove the fan and pulley from the water pump. Remove the fan shroud. 7. Remove the upper radiator hose. Remove the heater hoses from the radiator fill neck, water pump, and intake manifold. Loosen the clamps from the water pump by-pass hose. 8. Remove the alternator adjusting support bracket from the water pump. Disconnect the alternator harness and position aside. Remove the alternator. For additional information, refer to Section 14-02A. 9. Disconnect the diverter valve hose from the air management muffler. Disconnect the downstream hoses from the air management tubes. Remove the nuts retaining the air management tube brackets to the right exhaust manifold, and remove the brackets from the manifold. Remove the ground wire from tube brackets and position aside. 10. Disconnect the vacuum hoses from the EGR vacuum reservoir tank, air by-pass valve, and from the air management silencer on the right inner fender. 11. Remove the alternator bracket from the right cylinder head with the air pump, hoses and tubes attached. 12. Remove the engine-lifting eye from the front of the right cylinder head. 13. Disconnect the A/C compressor clutch, A/C high pressure cut-off, and the distributor connector and locator. 14. Remove the A/C manifold bolt from the rear of the compressor. Remove the A/C manifold lines and two locators. Install protective caps. 15. Remove the power steering pressure line and return hose. Install protective caps. 16. Remove the belt tensioner. Remove the A/C compressor and power steering pump bracket with the pump and compressor attached. 17. Disconnect the tube at the valve cover, and position the valve and tube out of the way. Disconnect the wiring connector from the canister purge solenoid. 18. Disconnect the spark plug wire boots, the locators, and the coil wire from the left and right side of the engine. Remove the distributor cap with wires attached. 19. Mark the relation of the rotor to the distributor housing and the distributor housing to the engine block for reassembly. Remove the distributor. For additional information, refer to Section 03-07A. 20. Remove the engine vacuum harness from the engine. Disconnect the air by-pass valve, TPS, EVP, EGR, IAC, locator, coil connector, radio noise suppressor, EVR, TAD solenoid, brake vacuum hose, and 42-pin electrical connector from left inner fender. 21. Remove the coil bracket assembly from the left exhaust manifold and intake. Remove the nut that retains the oil level indicator tube to the exhaust manifold and position the tube aside. 22. Disconnect the EGR tube flange nut from the EGR valve. 23. Remove the accelerator cable bracket and cable from the throttle body and position aside. Disconnect the MAP sensor vacuum hose. 24. Remove the upper intake manifold and tape the lower intake ports. 25. Remove the thermostat housing and discard the gasket. Disconnect the oil pressure-sending unit. 26. Depressurize the fuel system using EFI/CFI Fuel Pressure Gauge T80L-9974-B. For additional information, refer to Section 03-04B. 27. Remove the locking clips from the pressure and return fuel line spring lock couplings. Using spring lock coupling disconnect tools (D87L-9280-A, or equivalent, for 3/8-inch line, D87L-9280-B, or equivalent, for 1/2-inch line) disconnect the couplings. Install protective caps. 28. Remove the lower intake manifold with harness and injectors attached. Discard the gasket and tape the ports of cylinder heads. 29. Raise the vehicle. For additional information, refer to Section Remove the hose from the downstream air management tube to converter and remove the retaining bolt from the rear of the right cylinder head. 31. Remove the exhaust crossover pipe retaining nuts at the manifolds. 32. Remove the EGR valve tube from the left exhaust manifold. Remove the air management tube from the left exhaust manifold. 33. Lower the vehicle.

2 Page 2 of Remove the bolt from the rear of right cylinder head that retains the left air management tube. Remove the bolt retaining the fuel line bracket and transmission filler tube. Remove the filler tube and indicator. 35. NOTE: Identify the location of each rocker arm. Each rocker arm is to be installed in the original location to prevent premature wear. Identify the location of each push rod. Each push rod is to be installed in the original location to prevent premature wear. Remove the left valve cover, rocker arms, and push rods. 36. NOTE: The two lower rear head bolts will stay in the head until the head is removed. Remove the left cylinder head and gasket. Discard the gasket. 37. NOTE: Identify the location of each rocker arm. Each rocker arm is to be installed in the original location to prevent premature wear. Identify the location of each push rod. Each push rod is to be installed in the original location to prevent premature wear. Remove the right valve cover, rocker arms, and push rods. 38. NOTE: The lower rear head bolt will stay in the head until the head is removed. Remove the right cylinder head and gasket. Discard the gasket. 39. Remove the gaskets and clean both rocker covers. 40. Clean the upper intake manifold. 41. Clean the lower intake manifold. 42. Clean both cylinder heads and mating surfaces. Installation 1. NOTE: If the cylinder head was removed for head gasket replacement, check cylinder head and cylinder block gasket surfaces for flatness. If left or right exhaust manifold was removed, coat cylinder head and exhaust manifold port areas with film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B and install left or right exhaust manifold to cylinder head. Position the two long cylinder head attaching bolts in two rear lower bolt holes of the left and right cylinder heads. Place a long cylinder head attaching bolt in rear lower bolt hole of right cylinder head. Use rubber bands to retain bolts in position, above the head-to-block mating surface, until cylinder heads are installed. 2. Position new head gaskets on cylinder block, position over block dowels. Do not apply sealer to head gasket surfaces. Position the cylinder heads on the engine block and install remaining attaching bolts (longer bolts in lower row of bolt holes). Tighten all cylinder head attaching bolts in sequence shown in three steps: first to 95 Nm (70 lb-ft), then to 136 Nm (100 lb-ft), and finally to 176 Nm (130 lb-ft). When this procedure is used, it is not necessary to tighten bolts after extended operation. 3. Install push rods in original positions. Apply Engine Assembly Lube D9AZ D or equivalent meeting Ford specifications ESB-M1C93-B to valve stem tips and push rod ends. Make sure the lower ends of push rods remain seated in the valve tappets. 4. NOTE: Make sure the rocker arm seat base is inserted into its slot on the cylinder head before tightening the rocker arm seat bolts. Lubricate and install the rocker arms in original positions. Tighten the rocker arm seat bolts to 30 Nm (22 lb-ft). 5. Install new valve cover gaskets. Install the valve covers and tighten the bolts to 12 Nm (9 lb-ft). 6. Position the secondary air injection tube between the head and the air management tube and install the mounting bolt. Install the fuel bracket and the transmission filler tube. Tighten the transmission filler tube bolt to 19 Nm (14 lb-ft). 7. Raise the vehicle. 8. Tighten the bolt to the rear of the right cylinder head that retains the left air management tube to 16 Nm (12 lb-ft). 9. Loosely install the EGR valve tube to the left exhaust manifold. Install the air management tube to the left exhaust manifold. Tighten tube to 40 Nm (30 lb-ft). 10. Install the hose to the downstream air management tube on the converter. Tighten the bolt on the rear of the right cylinder head to 20 Nm (15 lb-ft). 11. Tighten the fuel line bracket bolt to 52 Nm (38 lb-ft). 12. Install the exhaust crossover pipe retaining nuts. Tighten the nuts to 34 Nm (25 lb-ft). 13. Lower the vehicle. 14. NOTE: Apply a bead of Silicone Gasket and Sealant F6AZ AA or equivalent meeting Ford specification WSE-M4G323-A6 in four places where the cylinder head and cylinder block meet. Remove the protective tape covering the ports of the cylinder heads. Install the intake manifold gaskets and seals. 15. NOTE: Connect the by-pass hose from the water pump to the intake manifold as you install the intake manifold. Install the lower intake manifold with harness and injectors attached. Tighten the retainers down in a three-step run-down procedure. Install the nuts onto studs in each corner of the intake. Tighten the bolts in sequence shown to 16 Nm (11 lb-ft). Then tighten the nuts to 16 Nm (11 lb-ft). Tighten the nuts and bolts down to 30 Nm (22 lb-ft) in sequence shown. Tighten nuts and bolts down to 47 Nm (35 lb-ft) in sequence shown. Repeat last step to make sure intake has seated.

3 Page 3 of NOTE: Lube, inspect, and replace the O-rings if necessary. Remove the protective caps. Connect the pressure and return fuel line spring lock couplings. Install the locking clips. Connect the oil pressure-sending unit. 17. Install the thermostat housing and a new gasket. Tighten the bolts to 30 Nm (22 lb-ft). Tighten the intake-to-water by-pass hose clamp. 18. NOTE: Start the EGR exhaust tube to the EGR valve as the upper intake manifold is installed. Remove the tape from the lower intake ports. Install the upper intake manifold and tighten to 14 Nm (10 lb-ft). Tighten EGR tube nut to 40 Nm (30 lb-ft). 19. Install the accelerator cable bracket and cable to the throttle body. Tighten the retainers to 17 Nm (13 lb-ft). Connect the canister purge valve tube to the valve cover and the MAP sensor vacuum line. Connect the wiring connector to the canister purge valve. 20. Install the distributor into engine using the alignment marks on the rotor, distributor housing, and engine block. Tighten the hold-down bolt to 17 Nm (13 lb-ft). 21. Install the coil bracket assembly to the left exhaust and intake manifolds. Tighten the nuts to 15 Nm (11 lb-ft). Install the nut that retains the oil level indicator tube to the exhaust manifold. Tighten the nut to 15 Nm (11 lb-ft). 22. Install the brake vacuum hose and engine vacuum harness. Connect the air by-pass valve, TPS, EVP, EGR, EVR, TAD solenoid, ignition coil, radio noise suppressor, and 42-pin electrical connectors to the left inner fender. Tighten the 42-pin electrical connector to 5 Nm (45 lb-in). 23. Install the distributor cap. Connect spark plug boots, locators, and coil wire. 24. Position the A/C and P/S mounting bracket over the water pump stud and secure to cylinder head with four bolts tightened to 54 Nm (40 lb-ft). Tighten bracket-to-water pump nut to 41 Nm (30 lb-ft). 25. Remove protective caps and install the power steering return line. Remove caps and replace power steering pressure line Teflon seal using tool D90P-3517-A. Install the pressure line. Tighten the line fitting to 35 Nm (25 lb-ft). 26. NOTE: Lube the O-rings with A/C refrigerant oil. Inspect and install new O-rings as necessary. Install the two locators at the bulkhead. Remove the protective caps. Inspect and lube the O-rings with A/C refrigerant oil. Install the A/C manifold lines to the A/C compressor. Tighten the bolt to 18 Nm (13 lb-ft). Position the vacuum hose for the heater control. 27. Connect the discharge line at the condenser. Tighten the fitting to 24 Nm (17 lb-ft). 28. Connect the line at the suction accumulator drier. Tighten the fitting to 44 Nm (32 lb-ft). 29. Connect the A/C coil connector, A/C high pressure cut-off, and the distributor connector and locator. 30. Install the engine-lifting eye to the front of the right head. Tighten the bolts to 34 Nm (25 lb-ft). Install the belt tensioner and tighten the bolt to 68 Nm (50 lb-ft). 31. Install the alternator mounting bracket to the right cylinder head. Tighten bolts to 54 Nm (40 lb-ft). 32. Install the alternator adjusting arm bracket to the water pump. Tighten the bolts to 41 Nm (30 lb-ft). Loosely install the alternator. Connect the alternator harness and tighten the nut to 9 Nm (80 lb-in). 33. Connect the vacuum hose to the diverter and valve hose to the air management muffler. Connect the hose to the air pump silencer. Install the nuts to the right exhaust manifold retaining the air management tube brackets. Tighten the nuts to 17 Nm (13 lb-ft). Install the ground wire on the tube bracket. Tighten the nut to 10 Nm (89 lb-in). 34. Connect the downstream hose from tube, and hose from the emission tubes from the rear of each cylinder head. Connect the vacuum connectors to the EGR vacuum reservoir tank. 35. Raise the vehicle. 36. Position a drain pan and drain the engine oil. 37. Remove the drain pan. 38. Tighten the EGR valve tube to exhaust manifold to 40 Nm (30 lb-ft). 39. Lower the vehicle. 40. Install the heater hoses to the water pump and to the intake manifold.

4 Page 4 of Install the fan shroud. Install the water pump pulley and fan to water pump hub with four bolts. Tighten the water pump pulley and fan bolts to 16 Nm (12 lb-ft). Tighten the shroud bolts to 6 Nm (53 lb-in). 42. Install all drive belts and adjust. Tighten the alternator bolts to 24 Nm (18 lb-ft). For additional information, refer to Section Install the upper radiator hose. Install the heater hose to the radiator fill neck. Install the bolts retaining the tube to the radiator. Tighten the bolts to 5 Nm (44 lb-in). 44. Install the air inlet tubes and connect the air by-pass hose. Install the crankcase breather hose. 45. Fill the cooling system. 46. Fill the crankcase with the correct viscosity and amount of engine oil. 47. Evacuate and recharge the A/C system. For additional information, refer to Section 12-03A. 48. Connect the negative battery cable. For additional information, refer to Section Start the engine and check for oil leaks. A/C Compressor Mounting Bracket Item Part Number Description 1 19B890 Air Conditioning Hose Assy 2 N S2 Bolt, M x Oil Level Indicator Tube 4 3A674 Power Steering Pump Stud A/C Compressor Mounting Bracket 7 N S8M Screw, M x A733 Power Steering Pump Pulley S2 Nut, 3/ S2 Bolt, 7/16-14 x S2 Bolt, 1/2-13 x B209 Drive Belt Tensioner Belt Idler Pulley 14 N S2 Bolt, M x A/C Compressor A Tighten to Nm (18-23 Lb-Ft) B Tighten to Nm

5 Page 5 of 6 (30-40 Lb-Ft) C Press Flush ± mm (0.010 Inch) D Tighten to Nm (40-53 Lb-Ft) E Tighten to Nm (50-68 Lb-Ft) Accessory Bracket, Right Item Part Number Description Generator Generator Adjusting Arm S36 Screw, 3/8-16 x 1.25 Used with Small Frame Generator S36 Bolt, 3/8-16 x S2 Bolt, 3/8-16 x S2 Bolt, 7/16-14 x S2 Bolt, 7/16-14 x S2 Bolt, 3/8-16 x S36 Bolt, 3/8-16 x Generator Mounting Bracket 11 N S2 Screw and Washer, M6-1.0 x B447 Secondary Air Injection Pump Pulley 13 9A486 Secondary Air Injection Pump 14 19A216 Idler Assy (California, Only) 15 8A620 Idler Support Bracket (California Only) S36 Bolt, 3/8-16 x Water Pump Pulley Drive Belt, 6k x 67.5 w/o A/C and 6k x 68.6 with A/C S36 Bolt, 3/8-16 x Crankshaft Pulley Drive Belt, 6k x 49.5 Small and Medium Frame Generator 6k x 50.5 Large Frame Alternator A Tighten to Nm (30-40 Lb-Ft) B Tighten to Nm (40-53 Lb-Ft) C Tighten to Nm (9-11 Lb-Ft)

6 Page 6 of 6

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages. 2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

Page 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

INTAKE MANIFOLD INSPECTION/REPLACEMENT

INTAKE MANIFOLD INSPECTION/REPLACEMENT ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

1988 Ford F-350 PICKUP

1988 Ford F-350 PICKUP 1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are

More information

SECTION C Engine 5.4L (3V)

SECTION C Engine 5.4L (3V) 303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front

More information

Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft

More information

2006 Expedition/Navigator Workshop Manual

2006 Expedition/Navigator Workshop Manual 7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

IN-VEHICLE REPAIR. Upper Intake Manifold

IN-VEHICLE REPAIR. Upper Intake Manifold 303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric

More information

IN-VEHICLE SERVICING > VALVE COVER - RH

IN-VEHICLE SERVICING > VALVE COVER - RH Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG

More information

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How 1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

IN-VEHICLE REPAIR. Engine Front Cover

IN-VEHICLE REPAIR. Engine Front Cover 303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP

More information

2011 Mercury Grand Marquis LS

2011 Mercury Grand Marquis LS Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.

More information

Engine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)

Engine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A) SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

DISASSEMBLY Procedure revision date: 11/22/2001

DISASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS 5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

ASSEMBLY Procedure revision date: 11/22/2001

ASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

Engine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070

Engine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070 SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)

More information

Page 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301).

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top

More information

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH) Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,

More information

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref... Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch

More information

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)

Engine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D) SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576

More information

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent 303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

Page 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C

More information

1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove...

1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove... Page 1 of 6 1994 Ford Mustang : Engine Mechanical > Engine Mechanical Components > Timing Chain Cover & Seal > Removal & Installation > 5.0L Engine 5.0L Engine 1. Disconnect the negative battery cable

More information

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07 26770_U07.qxd 8/30/05 3:01 PM Page 8 7-8 06025-S10P-C07 06025-S10P-C08 26770_U07.qxd 8/30/05 3:01 PM Page 9 7-9 06025-S10P-C09 26770_U07.qxd 8/30/05 3:01 PM Page 10 7-10 06025-S10P-C10 26770_U07.qxd 8/30/05

More information

Page 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

2001 Lincoln LS Workshop Manual

2001 Lincoln LS Workshop Manual Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional

More information

2000 Nissan Altima SE

2000 Nissan Altima SE Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

Page 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

1999 Nissan Altima GLE

1999 Nissan Altima GLE TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure

More information

Intake Manifold Replacement

Intake Manifold Replacement Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

2006 Freestar/Monterey Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 12/01/2005

2006 Freestar/Monterey Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 12/01/2005 SECTION 303-01: Engine 3.9L and 4.2L IN-VEHICLE REPAIR Procedure revision date: 12/01/2005 Valve Cover LH Item Part Number Description 1 W708650 Oil level indicator tube bolt 2 6754 Oil level indicator

More information

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine

More information

SECTION C Engine 5.4L (4V)

SECTION C Engine 5.4L (4V) 303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep

More information

1998 F-150/250 Workshop Manual

1998 F-150/250 Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation. 1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

05-08 GT. Hellion Power Systems Mustang Kit Instructions

05-08 GT. Hellion Power Systems Mustang Kit Instructions Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

SECTION A Engine 3.7L

SECTION A Engine 3.7L 303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone

More information

Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,

More information

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper) ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

SECTION C Engine 6.4L Diesel

SECTION C Engine 6.4L Diesel 303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft

More information

Steering Pump. NOTE: Always use these tags when requesting service assemblies as there may be slight differences in internal components.

Steering Pump. NOTE: Always use these tags when requesting service assemblies as there may be slight differences in internal components. file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb2a01.htm~gen~ref.htm Page 1 of 3 Section 11-02A: Steering Pump, Power, C-II DESCRIPTION AND OPERATION 1997 Aerostar, Ranger Workshop Manual Steering

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX) 2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

11A-1 ENGINE CONTENTS

11A-1 ENGINE CONTENTS 11A-1 ENGINE CONTENTS ENGINE ENGINE ... 11A... 11B 11A-2 ENGINE CONTENTS GENERAL... 3 Outline of Changes... 3 GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL

More information

Intake Manifold Replacement

Intake Manifold Replacement Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

2004 F-150 Workshop Manual

2004 F-150 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047

More information

Installation Instructions

Installation Instructions Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI

More information

2003 Explorer Sport/Sport-Trac Workshop Manual. 7. Disconnect the vacuum harness connector. Remove the nut.

2003 Explorer Sport/Sport-Trac Workshop Manual. 7. Disconnect the vacuum harness connector. Remove the nut. 7. Disconnect the vacuum harness connector. Remove the nut. 8. Remove two nuts, one bolt, and the A/C evaporator housing (19850). Remove the nut located at the bottom of the A/C evaporator housing first.

More information

Intake Manifold Removal (Upper)

Intake Manifold Removal (Upper) Intake Manifold Removal (Upper) Disconnect the vacuum lines from the upper intake manifold. Disconnect the MAP sensor electrical connector. Remove the MAP sensor screws. Remove the MAP sensor. Remove the

More information

TSI Date Group No. Supp. Page

TSI Date Group No. Supp. Page Volvo Trucks North America, Inc. Greensboro, NC USA Timing Gear Cover TSI Date Group No. Supp. Page 11.2001 215 006 1(7) Timing Gear Cover D12C Fig. 1: VOLVO D12C Engine W2003244 This information covers

More information

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit # 2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter

More information

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front

More information

Cylinder Head Removal

Cylinder Head Removal 2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors

More information