10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove
|
|
- Lester Glenn
- 5 years ago
- Views:
Transcription
1 1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable. 2. Unplug the radiator fan electric connections.
2 2 of Remove the top engine cover. 4. Remove the charge air pipe and bypass pipe with valve, keep the O-ring from the connection to the turbocharger intake pipe. 5. Remove the heat shield over the exhaust manifold. 6. Remove the power steering system's fluid reservoir.
3 3 of Undo the oil pipe for the power steering servo pump, the clip for the A/C expansion tank and the clip for the radiator vent hose from the radiator crossmember and bend the oil pipe to one side. 8. Remove the bracket from the battery tray and bend it aside. 9. Remove the radiator fan cowling, 2 bolts. Tilt the radiator fan cowling, twist up and lift out.
4 4 of Place a receptacle under the car and remove the gearbox oil pipe on the oil cooler. Remove the screw securing the pipe to the cooler and plug the connections (auto).
5 5 of Remove the front grille. 12. Remove headlamps and light clusters. 13. Remove the 2 air shields. 14. Remove the horn. 15. Open the expansion tank pressure cap to release system pressure. 16. Raise the car. 17. Remove the lower air shields. 18. Drain the coolant by connecting a hose and opening the drain plug. Collect the coolant in a suitable receptacle. 19. Tighten the drain plug.
6 6 of Unbolt the bottom of the charge air cooler, 2 bolts. 21. Unbolt the bottom of the oil cooler, 3 bolts. Bend the oil cooler aside and secure with a cable tie or similar. 22. Unbolt the bottom of the condenser, 2 bolts.
7 7 of Detach the outlet hose from the turbocharger. 24. Detach the outlet hose from the charge air cooler. 25. Lower the car to the floor. 26. Detach the upper hose from the radiator. 27. Detach the lower hose from the radiator. 28. Remove the clips securing the radiator to the radiator crossmember and pull the radiator up out of the rubber mountings. 29. Unhook the condenser from the mountings on the radiator. 30. Tilt the radiator away from the radiator crossmember and disconnect the vent from the expansion tank. 31. Cut off the clip securing the A/C compressor cable to the radiator. 32. Lift out the radiator. To fit 1. Lubricate the radiator upper rubber bushes with non-acidic Vaseline, part no , or the equivalent. 2. Lift the radiator into place but do not press it home.
8 8 of Fit the bleed hose to the expansion tank. 4. Hook the condenser onto the mountings on the radiator. 5. Press the radiator home and fasten the 2 clips that secure the radiator to the radiator member.
9 9 of Fasten the A/C compressor's lead to the radiator with a new clip. 7. Attach the radiator's lower hose. 8. Attach the turbocharger's outlet hose and the charge air cooler's outlet hose. 9. Raise the car.
10 10 of Bolt the bottom of the condenser in place, 2 bolts. 11. Remove the cable tie and fit the oil cooler, 3 bolts. 12. Bolt the bottom of the charge air cooler in place, 2 bolts.
11 11 of Fit the two lower air shields. 14. Make sure the cooling system drain plug is tight. Fit the lower air shields and lower the car.
12 12 of Fit both air shields (by the side of the condenser). 16. Fit the light clusters and headlamps. 17. Fit the horn and front grille.
13 13 of Attach the gearbox oil pipes to the oil cooler (auto). Tightening torque 25 Nm (19 ft. lbs.) 19. Fit the screw securing the pipe to the radiator Tightening torques 20. Lift the radiator fan cowling into place and fit the 2 bolts.
14 14 of Attach the radiator's upper hose. 22. Mount the bracket on the battery tray. 23. Fit the power steering system's fluid reservoir. 24. Fit the oil pipe for the power steering servo pump and the clips for the radiator vent hose as well as the clip for the A/C expansion tank. 25. Plug in the radiator fan's plugs.
15 15 of Fit the heat shield over the exhaust manifold. 27. Fit the charge air pipe. 28. Fit the bypass pipe with valve. Use a new O-ring for the connection to the turbocharger intake pipe. 29. Fit the top engine cover. 30. Fit the battery and connect its vent hose. 31. Fill up with coolant. For the correct mixture, refer to Coolant, Specifications. Close the filler cap. 32. Bleed the system as follows: Note: A/C and ACC must be OFF. Fill the cooling system to MAX level. Close the cap on the expansion tank, start the engine and warm it up at various engine speeds until the radiator fan starts. Carefully open the cap and top up to MAX. 33. Raise the car to check for oil or coolant leakage. 34. Lower the car and top up with coolant / transmission fluid (aut) as necessary 35. Set the clock and radio code where applicable ALLDATA, LLC. All Rights Reserved. (Version )
1 of 13 10/12/2013 2:20 PM
1 of 13 10/12/2013 2:20 PM Coolant Pump, 4-cyl. Warning: Take care if the car is warm. The coolant is hot and there is also a risk of burning yourself on the manifold. To Remove 1. Open the cap on the
More informationFan Shroud: Service and Repair Fan cowling To remove 1. Remove the upper engine cover.
Fan Shroud: Service and Repair Fan cowling To remove 1. Remove the upper engine cover. 2. Remove the battery cover and undo the battery cables. 3. Remove the battery cooling pipe by releasing it from the
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Engine block heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationSaab 9-5 B205, B Installation instructions MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE.
SCdefault 9-5 Installation instructions SITdefault Parking heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationEngine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane
Engine Remove and Install ( 34 0) Special Tools 068 A 068A Engine lifting tackle 4 003 Coolant hose clamp removal and fitting tool Workshop Equipment Transmission jack Trolley jack Workshop crane Materials
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More information1 of 8 1/17/2017 8:18 AM
Timing Belt Service and Repair, Removal and Replacement: Replacing... http://repair.alldata.com/alldata/article/display.action?componentid=64&... 1 of 8 1/17/2017 8:18 AM Replacing the timing belt Special
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More information900 Installation instructions. SCdefault
12 788 439 1 SCdefault 900 Installation instructions SITdefault Timer kit MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationRemoving the engine. General. Tools. Work description. Preparatory work
General General Applies to 9 and 13 litre engines with XPI, PDE or GAS and cylinder block generation 2. Tools Examples of suitable tools from Scania: Part number Designation 98 094 Lifting chain 99 318
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationSaab 900 M94-98, Saab 9-3, Saab 9000, Saab 9-5
SCdefault 900 Monteringsanvisning SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTALLATIONS DE MONTAGE Branch cable set LHD Accessories Part No. Group Date Instruction Part
More informationTURBOCHARGER UPGRADE; N20 INSTALLATION INSTRUCTIONS PART NUMBER D
TURBOCHARGER UPGRADE; N20 INSTALLATION INSTRUCTIONS PART NUMBER D310-0120 APPLICATION: 2014-16 F22 228i & xdrive coupe 2015-16 F23 228i & xdrive convertible 2012-16 F30 328i & xdrive sedan 2014-16 F31
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More informationVolkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19)
19 Engine-Cooling system (Page GR-19) Cooling system components, removing and installing Continued coolant circulation pump (V51), checking Coolant hose connection diagram Coolant pump, removing and installing
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More informationEngine and A4LDE Automatic Transmission Remove and Install ( ) Remove
Engine and A4LDE Automatic Transmission Remove and Install ( 3 0) Special Tools 068A -068A Engine lifting bracket -540 Bolt tightening angle gauge Workshop Equipment Transmission jack Workshop crane Assembly
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationMONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTALLATIONS DE MONTAGE
SCdefault 9-5 Monteringsanvisning SITdefault Engine/cabin heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTALLATIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More information2002 Jeep Grand Cherokee Laredo
Removal WARNING: DO NOT REMOVE THE CYLINDER BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR. REFER TO COOLING SYSTEM DRAINING.
More informationCooling system components, removing and installing
Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
More informationCooling system components, removing and installing
19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured
More information2008 Saturn Aura V6-3.6L
1 of 14 7/17/2016 7:26 PM 2008 Saturn Aura V6-3.6L Vehicle» Engine, Cooling and Exhaust» Cooling System» Radiator» Service and Repair» Radiator Replacement Radiator Replacement (LY7 - Gas, 6 Cyl, 3.6L,
More informationRemoving and Installing Battery
ALLDATA Online - 2005 Porsche 911 GT3 (996) F6-3.6L - Removing and Installing Bat... Page 1 of 13 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationEngine Removal and Installation
Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle
More information1999 Villager Workshop Manual
Page 1 of 5 SECTION 303-03: Engine Cooling 1999 Villager Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/27/1998 Cooling System Draining, Filling And Bleeding Draining WARNING: Do not open
More informationInstallation instructions, accessories - Electric engine block heater
S60 / V70 (00-08) / S80 (-06) / V70 XC (01-) / XC70 (-07) / XC90 Section Group Weight Year Month (Kg/Pounds) 8 876 2/4.4 2006 09 S60 2001 D5244T, S60 2002 D5244T, S60 2002 D5244T2, S60 2003 D5244T, S60
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationTiming Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar
Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationM-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationTiming Chain - Renew ( )
«Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140
More informationFULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
More informationTURBOCHARGER UPGRADE; N55 INSTALLATION INSTRUCTIONS. PART NUMBER D or D
TURBOCHARGER UPGRADE; N55 INSTALLATION INSTRUCTIONS PART NUMBER D310-0110 or D310-0115 APPLICATION: 2014-16 F22 M235i & xdrive coupe 2015-16 F23 M235i & xdrive convertible 2012-15 F30 335i & xdrive sedan
More informationSECTION 1D1 M162 ENGINE COOLING
SECTION 1D1 M162 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More information1 of 3 3/1/ :50 AM
Fan Clutch Service and Repair, Removal and Replacement http://repair.alldata.com/alldata/article/display.action?componentid=76&... 1 of 3 3/1/2016 11:50 AM Coupling unit - Viscous Fan Service Repair No
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More information2002 Taurus/Sable Workshop Manual
SECTION 211-02: Power Steering REMOVAL AND INSTALLATION 2002 Taurus/Sable Workshop Manual Power Steering Pump Pulley CII Pump Special Tool(s) Installer, Power Steering Pump Pulley 211-009 (T65P-3A733-C)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SJA-200 2008 FIT AII 37494 Issue Date JUL 2007 PARTS LIST Engine block heater Aluminum washer Heater harness Protective
More informationSaab 900 M94-98, Saab 9-3, Saab 9-5
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Branch cable set LHD Accessories Part No. Group Date Instruction
More informationSECTION 1D2 M161 ENGINE COOLING
SECTION 1D2 M161 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39552 ENGINE BLOCK 2009 RDX Issue Date P/N 08T44-SJA-200 MAY 2008 PARTS LIST NOTE: NOTE: Installation of the engine block heater requires
More information2016+ NISSAN TITAN XD
PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling
More information1 of 27 7/21/2015 3:33 PM
1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work
More informationIncludes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps
Includes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps WARNING: This product is not legal for sale or use on pollution controlled vehicles
More informationPage 1 of 6 Fuel Charging and Controls - Turbocharger - 2.7L V6 - TdV6 - Turbocharger RH Removal and Installation Special Tool(s) Engine support beam 303-021 Engine lifting brackets 303-1129 Removal 1.
More informationInstallation instructions, accessories - Fuel driven heater 912-D
XC90 Section Group Weight(Kg/Pounds) Year Month 8 87 2002 10 XC90 2003 D5244T, XC90 2004 D5244T, XC90 2005 D5244T AW50/51 AWD, XC90 2006 D5244T, XC90 2006 D5244T AW50/51 AWD D5244T R8703687 Page 1 of 20
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK (L4) P/N 08T44-TA0-100 Application 2008 ACCORD 2-AND 4-DOOR Publications No. AII 35355 Issue Date AUG 2007 PARTS LIST Engine block heater Coolant concentration
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationInstallation instructions, accessories. Electric engine block heater, 230V, 5 cyl diesel
Installation instructions, accessories Instruction No 30795311 Version 1.2 Part. No. 31373138 Electric engine block heater, 230V, 5 cyl diesel IMG-256423 Volvo Car Corporation Electric engine block heater,
More informationFMK265SD F L DIESEL WITH DUAL ALTERNATORS
WITH DUAL ALTERNATORS This kit will NOT work on trucks equipped with adaptive steering. INSTALLATION NOTES 1. Disconnect negative batteries cables. Remove the air duct from the passenger side and the black
More information26 - COOLING SYSTEM CONTENTS ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 COOLING SYSTEM FAULTS... 1
26 - COOLING SYSTEM CONTENTS Page LAND ROVER V8 DESCRIPTION AND OPERATION ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 FAULT DIAGNOSIS COOLING SYSTEM FAULTS... 1 REPAIR COOLANT - DRAIN
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More informationThis information covers the proper service procedures for the replacement of the radiator on a chassis with the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces SB 260-32, Cooling System Service, dated (1.2007), publication no. PV776-20177193. Radiator, Replacement DService Bulletin Trucks
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More information2006 Ford Pickup F350 Super Duty
Fig. 100: Identifying Evaporator Core Housing Components Removal All vehicles 1. Remove the suction accumulator. For additional information, refer to SUCTION ACCUMULATOR. 2. Remove the RH battery. For
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationWeistec True Downpipes
Weistec True Downpipes Installation Guide, W212, W218, AWD 2014+ E63 2014+ CLS63 WARNING! IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS, WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationReplacing the timing belt
"VCC116740 EN 20091209" 1(5) Replacing the timing belt Special tools: 999 5433, 999 5456 Removing the timing belt Note! As the illustrations in this service information are used for different model years
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationBody, front. Lock carrier with attachments, removing and installing
Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More informationSaab 9-5 B205, B235, B308
SCdefault 9-5 Installation instructions SITdefault Engine/cabin heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationCOOLING SYSTEM ON-VEHICLE INSPECTION CO 1
Radiator Cap Tester 2AZ-FE OLING OLING SYSTEM A112194E01 A112306 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK OLING SYSTEM FOR LEAKS (a) Remove the radiator reservoir cap. CAUTION: To avoid the danger
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More informationPARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More information2014 RAM C/V Tradesman
Fig. 91: Suction Hose Ball Valve NOTE: View typical 14. Open the suction hose's ball valve to begin refilling the cooling system. 15. When the vacuum gauge reads zero, the system is filled. NOTE: On some
More information1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857
More informationSHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationEngine Cooling. Cooling System Component Layout. https://myvpn.dealerconnection.com/extdealerlrprod/xml/parsexml.jsp,danainfo=gtr.fran...
Page 1 of 5 Published : Apr 28, 2004 Engine Cooling Cooling System Component Layout Item Part Number Description 1 - Heater hose, inlet and outlet 2 - Heater hose, inlet and outlet for vehicles with rear
More informationSR Performance Radiator Installation Instructions
List of Tools: SR Performance Radiator Installation Instructions Phillips Head Screwdriver 3/8 Ratchet 8mm socket 7mm socket Optional Dremel or file Installation Instructions: Step 1 Drain radiator by
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationValve Cover - RH Material
1 of 5 5/15/2015 8:06 AM Valve Cover - RH Material 2 of 5 5/15/2015 8:06 AM 3 of 5 5/15/2015 8:06 AM Removal CAUTION: During engine repair procedures, cleanliness is extremely important. Any foreign material,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK P/N 08T44-SWA-1A0 Application 2012 CIVIC 4-DOOR Si Publications No. AII 45627 Issue Date APRIL 2011 PARTS LIST Engine block heater Aluminum washer Heater
More informationInstallation manual. Cooling system. Industrial engines DC09, DC13, DC16 OC16. 01:05 Issue 12 en-gb. Scania CV AB 2018, Sweden
Installation manual Cooling system Industrial engines DC0, DC13, DC OC 333 3 01:05 Issue en-gb Changes from the previous issue...3 Design and dimensioning...3 Expansion tank...4 and earlier emission levels...
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationInstallation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S
Installation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S80 00-09 1. This instruction shows how to replace the OEM radiator with do88 performance radiator. At this type of installation
More informationTiming Chain Renew ( )
Timing Chain Renew (1 314 0) Special Tools 1 137 Oil seal installer/aligner, crankshaft front 1168 1 168 Crankshaft immobilising tool 1137 1 140 Engine support bar 4 003 Remover/installer, radiator hose
More informationCylinder Head Assembly: Service and Repair Replacing the Cylinder Head and Gasket
2002 Volvo V40 L4-1.9L Turbo VIN 29 B4204T3 Copyright 2009, ALLDATA 10.10 Page 1 Cylinder Head Assembly: Service and Repair Replacing the Cylinder Head and Gasket Cylinder Head/Gasket, Replacing Special
More information