2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
|
|
- Claud Bennett
- 5 years ago
- Views:
Transcription
1 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove the right splash shield. 4. Remove accessory drive belts. 5. Remove crankshaft damper. 6. Remove the lower torque strut. 7. Disconnect exhaust system from manifold. 8. Disconnect A/C pressure switch at rear of compressor housing. 9. Lower vehicle and support engine with a jack. 10. Discharge A/C system and disconnect A/C lines at coupling block. 11. Remove upper torque strut. 12. Remove screw attaching ground to strut bracket. 13. Remove torque strut bracket. 14. Remove upper radiator support crossmember. 15. Remove power steering pump and bracket. Set pump aside. Do not disconnect lines from pump. 16. With engine properly supported, remove right engine mount through bolt. 17. Raise engine with jack until engine support bracket bolts are accessible. 18. Remove support bracket bolts (Fig. 81). 19. Remove support bracket (Fig. 81).
2 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page Remove upper timing belt cover fasteners and remove cover (Fig. 80). 21. Remove lower timing belt cover fasteners and remove cover (Fig. 80). CAUTION: When aligning crankshaft and camshaft timing marks always rotate engine from crankshaft. Camshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before removing timing belt. 22. Before the removal of the timing belt, rotate crankshaft until the TDC mark on oil pump housing aligns with the TDC mark on crankshaft sprocket (trailing edge of sprocket tooth) (Fig. 82). NOTE: The crankshaft sprocket TDC mark is located on the trailing edge of the sprocket tooth. Failure to align trailing edge of sprocket tooth to
3 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 3 TDC mark on oil pump housing will cause the camshaft timing marks to be misaligned. 23. Install 6 mm Allen wrench into belt tensioner. Before rotating the tensioner, insert the long end of a 1/8" or 3 mm Allen wrench into the pin hole on the front of the tensioner (Fig. 83). While rotating the tensioner counterclockwise, push in lightly on the 1/8" or 3 mm Allen wrench, until it slides into the locking hole. 24. Remove timing belt. CAUTION: If timing belt was damaged due to incorrect tracking (alignment), the belt tensioner assembly must be replaced. NSTALLATION 1. Set crankshaft sprocket to TDC by aligning the sprocket with the arrow on the oil pump housing. 2. Set camshafts timing marks so that the exhaust camshaft sprocket is a 1/2 notch below the intake camshaft sprocket (Fig. 84). CAUTION: Ensure that the arrows on both camshaft sprockets are facing up.
4 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 4 3. Install timing belt. Starting at the crankshaft, go around the water pump sprocket, idler pulley, camshaft sprockets and then around the tensioner (Fig. 85). 4. Move the exhaust camshaft sprocket counterclockwise (Fig. 85) to align marks and take up belt slack. NOTE: A new tensioner is held in the wound position by a pull pin. 5. Remove the pull pin or Allen wrench from the belt tensioner.
5 2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 5 6. Once the timing belt has been installed and tensioner released, rotate the crankshaft two (2) complete revolutions. Verify that the TDC marks on crankshaft and timing marks on the camshafts are aligned as shown in (Fig. 86). 7. Install lower timing belt cover and tighten fasteners to 4.5 Nm (40 in. lbs.) (Fig. 80). 8. Install upper timing belt cover and tighten fasteners to 4.5 Nm (40 in. lbs.) (Fig. 80). 9. Install right engine support bracket. Ensure the power steering pump is properly located in mounting location on bracket. Tighten mount bracket bolts to 61 Nm (45 ft. lbs.) (Fig. 81). 10. Lower engine into mounting position and install right engine mount through bolt. Tighten bolt to 118 Nm (87 ft. lbs.). 11. Install power steering pump and bracket. 12. Install upper radiator support crossmember. 13. Install torque strut bracket to strut tower. 14. Connect ground strap to bracket. 15. Install upper torque strut. 16. Connect A/C lines and charge A/C system. 17. Raise vehicle. 18. Connect exhaust system to manifold. 19. Connect A/C pressure switch connector. 20. Install crankshaft damper. 21. Install accessory drive belts. 22. Install lower torque strut. 23. Perform torque strut adjustment procedure. 24. Install right splash shield. 25. Install right front wheel. 26. Connect negative cable to battery. 27. Perform camshaft/crankshaft synchronization procedure. Refer to: Engine : Service and Repair : Engine Overhaul : See: Service and Repair/Procedures/Engine Overhaul/Camshaft/Crankshaft Synchronization
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationChrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationVALVE TIMING CHECK-TIMING BELT COVER INSTALLED
TIMING BELT SERVICE VALVE TIMING CHECK-TIMING BELT COVER INSTALLED 1. Remove number one spark plug. 2. Using a dial indicator; set number one cylinder to TDC on the compression stroke. 3. Remove the access
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More information1992 Mitsubishi 3000GT VR-4
TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner
More informationTiming Belt: Service and Repair Removal and Installation Removal
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Removal and Installation Removal 1. Turn the crankshaft so its white mark (A) lines up with the
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationTIMING BELT REMOVAL - TIMING BELT
2004 Chrysler Concorde V6-3.5L VIN M Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Procedures TIMING BELT REMOVAL - TIMING BELT CAUTION: The following
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationRecommended Installation Procedure (31 MARCH 2010) ATech Timing Belt Tensioner (979004) EA T 20 Valve Longitudinal Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More information3/6/2017 Timing Chain Service and Repair, Removal and Replacement: Valve Timing, Installing and Adjusting
Valve timing, adjusting Special tools and equipment - T10068 Camshaft bar - T10069 Counter support - VAG 1331 Torque wrench (5-50 Nm) - VAG 1332 Torque wrench (40-200 Nm) - AMV 174 004 01 Sealing compound
More informationFig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover
Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More information2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More information2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page
More informationTiming Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
More information1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
More informationIntake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT
More information1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE).
1Search TIMING BELT 2005 Chrysler Pacifica 3.5L Eng Base FRONT TIMING BELT COVER REMOVAL 1. Perform fuel pressure release procedure. (Refer to FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE). 2. Disconnect
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationPage 1 of 5 Service Manual: TIMING BELT REPLACEMENT - 3.2L & 3.5L REMOVAL & INSTALLATION 1999 Chrysler 300M 3.5L Eng Question: Is a 3.5 a valve bender? - My Autodata book says every car is bender REMOVAL
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationTiming Belt: Service and Repair
1996 Honda Accord Sedan L4-2.2L SOHC (16 Valve) Copyright 2009, ALLDATA 9.90 Page 1 Timing Belt: Service and Repair TIMING BELT AND TIMING BALANCER BELT REMOVAL Timing Components NOTE: - Turn the crankshaft
More informationTOOTHED DRIVE BELT, REMOVING, INSTALLING AND TENSIONING
2005 Audi A4 Sedan (8E2) L4-1.8L Turbo (AMB) Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Removal and Replacement TOOTHED DRIVE BELT, REMOVING,
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
MAZDA 1.6L & 1.8L 4-Cylinder - 1986-95 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1992 and earlier model years, the manufacturer recommends the belt be replaced every 60,000 miles. For 1993-95
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More information10 +/- 2 degrees before top dead center (BTDC)
1996 Ford Contour L4-122 2.0L DOHC VIN 3 SFI Ignition Timing Adjustments Base ignition timing is referenced to the position of the crankshaft position sensor. It is set at 10 +/- 2 degrees before top dead
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationTiming Belt: Service and Repair Removal
2001 Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Removal Special Tools Required ^ Holder handle 07JAB-001020A ^ Holder attachment,
More information2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum
1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to
More information2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
More informationService and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
More informationRecommended Installation Procedure ATech Timing Belt Tensioner and AUDI 2.0L 4V FSI & TFSI Engine (19 January 2015)
The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must be installed
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More information2003 Land Rover Freelander S. CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed.
FRONT TIMING BELT CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed. Removal CAUTION: Camshaft timing belt must be replaced if cylinder head is to be
More informationIN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More informationService and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationCAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More information1998 Volkswagen Golf GL
Removal (Thermo Tensioner Roller - 1997 & Up) CAUTION: To prevent valves from contacting piston, DO NOT rotate camshaft or crankshaft with timing belt removed. Valve damage may result. 1. Remove air cleaner
More informationEngine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
More informationRecommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationService and Repair. Material. Timing chain
ALLDATA Online - 1999 Mercury Cougar V6-153 2.5L DOHC VIN L SFI - Service and... Page 1 of 16 Service and Repair Notes Material Timing chain 1. Remove and discard the camshaft seal. 2. Remove the engine
More informationTIMING BELT/CHAIN AND SPROCKETS
9-82 ENGINE 4.7L DN TIMING BELT / CHAIN COVER(S) (Continued) Fig. 130 Accessory Drive Belt Tensioner 1 - TENSIONER ASSEMBLY 2 - FASTENER TENSIONER TO FRONT COVER Fig. 132 Timing Chain Cover Fasteners (4)
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More informationRecommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
More informationATech Timing Belt Tensioner (979572) VM MOTORI 2.5L Diesel, Common Rail Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More information1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
More informationTIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
More information1990 Buick Electra Limited
4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner
More information1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
More informationTIMING BELT TENSIONER FOR AFTERMARKET RENAULT G8T 2.2L DIESEL ENGINE (Revision date: 06/24/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationRecommended Installation Procedure ATech Timing Belt Tensioner DaimlerChrysler PL, PT, JR 2.0L 4-Cyl. Engine (10/27/2003)
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to DAIMLERCHRYSLER PL s guidelines. The mounting of the TBT
More information2/25/2018 Engine, 4.0l Cylinder Head Removal 2008 Chrysler Town and Country (4.0L) - RT MotoLogic
2008 Town and Country (4.0L) - RT REMOVAL - CYLINDER HEAD(S) Labor Operations: Click to display a list of Labor Operations associated with this procedure Special Tools: Click to display a list of tools
More informationREMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
More informationInstallation Instructions
Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationTECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
More informationDistributor: Service and Repair Distributor Replacement REMOVAL PROCEDURE
2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W Copyright 2007, ALLDATA 9.50 Page 1 Distributor: Service and Repair Distributor Replacement REMOVAL PROCEDURE NOTE: There are two procedures available
More informationService and Repair SERVICE POINTS OF REMOVAL. Select Vehicle New TSBs Technician's Reference Mitsubishi 3000GT V6-2972cc 3.
1 of 12 5/4/2008 10:31 PM Home Account Contact ALLDATA Log Out Help METRO TOYOTA Select Vehicle New TSBs Technician's Reference 1992 Mitsubishi 3000GT V6-2972cc 3.0L DOHC Vehicle Level Engine, Cooling
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More information2002 Dodge Pickup R1500
CAUTION: Overtightening the tensioner arm torx bolt can cause severe damage to the cylinder head. Tighten torx bolt to specified torque only. Install left side chain tensioner arm. Apply Mopar Lock N,
More informationLEFT CYLINDER HEAD Engine, 3.5L/Cylinder Head/Removal
Page 1 of 9 09 - Engine, 3.5L/Cylinder Head/Removal LEFT CYLINDER HEAD Labor Operations: Click to display a list of Labor Operations associated with this procedure 1. Remove the engine cover. 2. Perform
More information2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)
Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with
More informationTiming Chain: Service and Repair
1996 Nissan-Datsun Truck D21 Hardbody 2WD L4-2389cc 2.4L SOHC MFI (KA24E) Copyright 2013, ALLDATA 10.52 Page 1 Timing Chain: Service and Repair *** THIS ARTICLE INCLUDES UPDATES MADE BY TSB 95027, DATED
More information1 of 15 1/26/2017 8:57 AM
1 of 15 1/26/2017 8:57 AM Timing Belt and Balancer Belt Removal Special Tools Required ^ Holder Handle 07JAB-001020A ^ Holder Attachment, 50 mm, Offset 07MAB-PY3010A ^ Socket, 19 mm 07JAA-001020A or a
More informationREMOVAL & INSTALLATION
Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip
More informationTORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43
More informationRecommended Installation Procedure (25 MAY 07) ATech Timing Belt Tensioner (979778) FIAT FIRE 8-valve 1.2/1.4L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower
More informationPage 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T-12270-A Removal NOTE: It is
More informationRECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More information& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.
Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More information