Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Size: px
Start display at page:

Download "Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly."

Transcription

1 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. To install, reverse removal procedure. Verify that the vehicle meets the following conditions: The vehicle is not in a Reduced Engine Power mode. The ignition is ON. The engine is OFF. Operate the accelerator pedal and observe the APP angles with a scan tool. The accelerator pedal should operate freely, without binding, between closed throttle and Wide Open Throttle (WOT). Inspect the carpet fit under the accelerator pedal.

2 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 2 of 41 Fig. 4: Locating APP Sensor BARO SENSOR Removal & Installation Turn OFF the ignition. Disconnect the BARO sensor electrical connector. See Fig. 5. Bend the locking tab, located on the bracket, away from the sensor, just enough so that the sensor will pass.

3 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 3 of 41 Pull the BARO sensor downward to remove it from the bracket. To install, reverse removal procedure. Fig. 5: Locating BARO Sensor BOOST SENSOR Removal & Installation (Calif.) 1. Turn OFF the ignition. Loosen the outlet duct clamp at the upper intake manifold cover. Remove he upper intake manifold cover from the outlet duct. Remove the upper intake manifold cover. Disconnect the electrical connector from the boost pressure sensor. See Fig. 6. Remove the bolt retaining the boost pressure sensor bracket. Disconnect the vacuum line from

4 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 4 of the sensor. Remove the boost pressure sensor and the bracket. Remove the bracket from the sensor. To install, reverse removal procedure. Inspect the boost pressure sensor seal for damage and replace as necessary. Fig. 6: Locating Boost Sensor (Calif.) Removal & Installation (Federal) Turn OFF the ignition. Remove the air cleaner outlet duct. Disconnect the electrical connector from the boost pressure sensor. See Fig. 7. Remove the nut retaining the boost pressure sensor bracket and the coolant tube. Lift the coolant tube off of the stud and move it out of the way. Remove the boost pressure sensor and the bracket from the intake manifold. Remove the bracket from the sensor. To install, reverse removal procedure. Inspect the boost pressure sensor seal for damage and replace as necessary.

5 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 5 of 41 Fig. 7: Locating Boost Sensor (Federal) CAMSHAFT POSITION SENSOR Removal & Installation

6 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 6 of 41 Remove the cooling fan. Disconnect the camshaft position sensor connector. See Fig. 8. Remove the cooling fan pulley. Remove the CMP sensor retaining bolt. Remove the CMP sensor. To install, reverse removal procedure. Fig. 8: Locating CMP Sensor (6.6L) CRANKSHAFT POSITION SENSOR NOTE: Some models require CRANKSHAFT POSITION (CKP) SENSOR VARIATION LEARN PROCEDURE to be performed when CKP sensor is

7 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 7 of 41 removed or replaced. See COMPUTER RELEARN PROCEDURES - DOMESTIC article in GENERAL INFORMATION. Removal & Installation Disconnect the batteries. Remove the CKP sensor connector. Remove the CKP sensor mounting bolt. Remove the CKP sensor. See Fig. 9. To install, reverse removal procedure. Fig. 9: Locating CKP Sensor (6.6L)

8 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 8 of 41 ECT SENSOR Removal & Installation Turn OFF the engine. Drain the coolant below the level of the ECT sensor. Disconnect the ECT sensor electrical connect. See Fig. 10. Remove the ECT sensor. To install, reverse removal procedure. Fig. 10: Locating ECT Sensor EGR VALVE Removal & Installation

9 ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 9 of Drain cooling system. Remove air intake duct. See Fig. 6. Remove the turbocharger boost sensor bracket bolt. Remove the turbocharger boost sensor with bracket. Remove the intake heater and gasket. Remove the upper intake manifold tube nuts and upper tube. Disconnect Exhaust Gas Recirculation (EGR) valve vacuum hose. Remove EGR inlet cooling hose from cooling tube. Remove EGR outlet cooling hose from cooling tube. Remove nuts retaining EGR assembly to intake manifold. Remove nuts retaining EGR assembly to exhaust pipe. Remove bolts retaining EGR assembly to EGR bracket. Remove EGR assembly from engine. Remove bolts retaining EGR to EGR cooling tube. Separate EGR from EGR cooling tube. To install, reverse removal procedure. EGR VALVE THROTTLE SOLENOID Removal & Installation Disconnect the negative battery cable. Remove the right turbo charged air hose. Disconnect the Exhaust Gas Recirculation (EGR) throttle valve solenoid electrical connector. See Fig. 11. Disconnect the EGR throttle valve solenoid vacuum lines. Remove the solenoid bolt and the solenoid. To install, reverse removal procedure.

10 Page 10 of 41 Fig. 11: Locating EGR Valve Throttle Solenoid EGR VALVE VACUUM PUMP Removal & Installation Remove the lower fan shroud. Remove vacuum line from Exhaust Gas Recirculation (EGR) valve vacuum pump. Remove the drive belt tensioner. Remove the drive belt idler pulley. Remove EGR vacuum pump mounting nuts. Remove the EGR vacuum pump. To install, reverse removal procedure. EGR VALVE VACUUM SENSOR Removal & Installation

11 Page 11 of 41 Disconnect the negative battery cable. Disconnect the Exhaust Gas Recirculation (EGR) valve vacuum sensor electrical connector. See Fig. 12. Disconnect the EGR valve vacuum sensor vacuum line. Remove the EGR valve vacuum sensor from the bracket. To install, reverse removal procedure. Fig. 12: Locating EGR Valve Vacuum Sensor EGR VALVE VENT SOLENOID Removal & Installation Disconnect the negative battery cable. Disconnect the Exhaust Gas Recirculation (EGR) valve vent solenoid electrical connector. See Fig. 13. Disconnect the EGR vent solenoid vacuum lines. Remove the EGR valve vent solenoid bolt and the solenoid. To install, reverse removal procedure.

12 Page 12 of 41 Fig. 13: Locating EGR Vent Valve Solenoid EGR VALVE SOLENOID Removal & Installation Disconnect the negative battery cable. Disconnect the Exhaust Gas Recirculation (EGR) valve solenoid. See Fig. 14. Disconnect the EGR valve solenoid vacuum lines. Remove the EGR valve solenoid bolt and the solenoid. To install, reverse removal procedure.

13 Page 13 of 41 Fig. 14: Locating EGR Valve Solenoid FUEL FILTER Removal Tips Click a link to view tip Tip: Duramax Diesel Fuel Filter Replacement Problems Tip: FUEL FILTER LIFE indicator reset Disconnect the negative battery cables. Install a hose to the water drain on the water-in-fuel sensor. See Fig. 15. Place the other end of the hose into an approved container. Drain as much fuel as

14 Page 14 of 41 possible from the fuel filter housing. Tighten the water drain on the water-in-fuel sensor. Disconnect the water-in-fuel sensor harness connector. Remove the fuel filter from the fuel filter/heater element housing. Remove the water-in-fuel sensor from the fuel filter. Installation Tips Click a link to view tip Tip: WIF Sensor Installation Tip: FUEL FILTER LIFE indicator reset NOTE: Inspect the fuel filter/heater element housing and the fuel filter for a dislocated filter seal or contamination. Contamination on the fuel filter/heater element housing may cause leakage at the fuel filter. Coat the seal with clean engine oil. Install the water-in-fuel sensor in the fuel filter. Install the fuel filter on the fuel filter/heater element housing. Connect the water-in-fuel harness connector. Pump Primer located on top of the fuel filter 30 times or until stiff. Connect the negative battery cables. Start the engine and inspect for fuel leaks.

15 Page 15 of 41

16 Page 16 of 41

17 Page 17 of 41 Fig. 15: Identifying Fuel Filter Components (6.6L) FUEL INJECTION CONTROL MODULE Removal & Installation Disconnect the batteries. Remove the duct between the air cleaner and the turbocharger inlet housing. Remove the clamp from the PCV hose to pipe and move the hose aside. Remove the fuel filler cap to relieve pressure. Remove the large tie wraps from the fuel injector control module and harness. Loosen the fuel lines at the fuel injection control module. Remove the 3 mounting bolts. Remove the insulators between the fuel injection control module and bracket by lifting up the module and reaching underneath. Disconnect the wiring harness connectors from the fuel injection control module. Disconnect the fuel lines at the fuel injection control module and discard washers. Remove the fuel injection control module from the bracket. See Fig. 16. Use NEW washers on fuel lines. Do not knock off the insulators when installing the fuel injector control module to the bracket. To install, reverse removal procedure.

18 Page 18 of 41 Fig. 16: Locating FICM FUEL INJECTION PUMP Removal & Installation NOTE: Cover the air intake pipe end with duct tape to prevent the infiltration of dirt.

19 Page 19 of Disconnect negative battery cables from both batteries. Remove the air intake duct between the air cleaner and the turbocharger inlet housing. Drain the coolant. Remove the upper fan shroud. Remove the fan blade assembly. Remove the serpentine belt. Remove the bolt holding the positive battery cable junction box and bracket and move out of the way. NOTE: Remove only the air conditioning/power steering bracket. Do not discharge the A/C or remove the A/C and power steering lines Remove the A/C compressor. See appropriate article in AIR CONDITIONING & HEATING. Remove the power steering pump. Position the A/C compressor and power steering pump aside. Remove the oil filler tube. Remove the air conditioning/power steering bracket. Remove the alternator. Remove the thermostat housing bracket, wiring and fuel test port, and two nuts. Remove the Positive Crankcase Ventilation (PCV) catch tank from the PCV bracket and bolt below holding lower line, and reposition. Remove the alternator bracket. Remove the turbo cooling hose return line clamp and hose. Remove the upper radiator hose at the outlet pipe. Remove the bracket and support the bracket at the valve cover, and swing out of the way. Remove bolt holding wiring support bracket at thermostat housing. Move the main wiring harness by disconnecting the fuel pressure regulator connector on the fuel injection pump and the fuel injection control module connectors. Flip the wire harness and harness tray towards the back and set aside. Disconnect the heater pipe bolt and temperature sensor wire from the thermostat housing. NOTE: Cap all of the open fuel connections with suitable plastic plugs in order to prevent infiltration of dirt Remove the air intake pipe. Remove the thermostat crossover assembly. Remove the hose to the turbo water feed line. Disconnect all high pressure fuel lines and remove supply pipe and hose at the fuel injection pump and function block. Remove the high pressure line from the injection pump to the junction block. Remove the fuel return hose from fuel injection pump. Remove the high pressure line from the injection pump to the junction block. Remove fuel injection pump from the block using two screwdrivers to work the pump from the block towards rear of engine keeping the pump straight. Remove fuel injection pump. See Fig. 17. To install, reverse removal procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.

20 Page 20 of 41 Fig. 17: Removing Fuel Injection Pump (6.6L) FUEL INJECTOR Tips Click a link to view tip Tip: Injector Sleeve

21 Page 21 of 41 Removal Remove the lower valve rocker arm cover. Remove the return line from injectors. Remove the retaining bolt from the injector bracket. Install the Fuel Injector Puller (J 44639) on the injector retainer bracket. Confirm which side of the banjo washers have the largest hole. Install a wrench on the J and pry away from the fuel injector. Remove the faulty injectors. See Fig. 18. Remove the copper compression washer from injection hole if the washer did not remove with the injector. Installation NOTE: Always install new copper gaskets on the fuel injector lines If the injector sleeve was pulled from the cylinder head when removing the injector(s), continue with this step. If the injector sleeve was not pulled from cylinder head, go to step 3. Clean the fuel injector sleeve bore with GM P/N or equivalent. Lubricate and install NEW "O" rings onto the fuel injector sleeve. Install the fuel injector sleeve onto the Fuel Injector Sleeve Remover/Installer (J 45910). Apply GM P/N United States or equivalent to the fuel injector sleeve lower sealing area. Install the fuel injector sleeve with J into the cylinder head. Lightly tap on the J with a hammer to install and seat the fuel injector sleeve. Remove the J from the fuel injector sleeve. Install the NEW injectors. Install the retaining bolt on the injector bracket. Install the return line fuel injector. Install the lower left valve rocker arm cover.

22 Page 22 of 41 Fig. 18: Removing Fuel Injector FUEL PRESSURE REGULATOR Removal & Installation 1. Remove the air intake pipe. Disconnect the Air Conditioning (A/C) compressor clutch electrical connector. Disconnect the A/C cut out switch electrical connector. Remove the drive belt. Remove the A/C compressor bolts. Move the A/C compressor with the hoses attached to the right side of the engine compartment.

23 Page 23 of Remove the water outlet tube. Disconnect both main harness electrical connectors. Remove both main harness electrical connector to bracket bolts. Remove the main harnesses from the bracket. Disconnect the Engine Coolant Temperature (ECT) sensor electrical connector. Disconnect the Barometric (BARO) pressure sensor electrical connector. Disconnect the glow plug relay electrical connectors. Disconnect the fuel rail temperature sensor electrical connector. Disconnect the left front fuel injector electrical connector. Disconnect the left rear fuel injector electrical connector. Disconnect the fuel pressure regulator electrical connector. Disconnect the oil level sensor harness electrical connector. Remove the Positive Crankcase Ventilation (PCV) hose from both valve covers. Reposition the injection pump inlet clamp. Remove the injection pump inlet hose from the fuel feed distribution (leak-off) block. Reposition the hose. Clean the fuel pressure regulator and high pressure injection pump thoroughly with solvent, such as GM P/N , or equivalent. Using compressed air, thoroughly blow dry the regulator and pump. Remove the 3 fuel pressure regulator screws using a T25 TORX(R). Remove the fuel pressure regulator. See Fig. 19. NOTE: DO NOT use compressed air to remove debris while the fuel pressure regulator is removed If dirt or debris is found in the bore or seating surfaces of the fuel injection pump, perform the following: Place a clean rag over the pump bore in order to collect the excess fuel. Bump the engine over in order to flush any debris out of the regulator bore. If the pressure regulator is being re-used, check the "O" rings for damage. If the "O" rings are damaged, install NEW "O" rings. Lubricate and install NEW "O" rings onto the regulator. Lubricate the "O" rings with clean, NEW engine oil. If the regulator is installed at an angle the "O" rings may be damaged, resulting in possible fuel leakage. To install, reverse removal procedure.

24 Page 24 of 41 Fig. 19: Locating Fuel Pressure Regulator FUEL PUMP Tips Click a link to view tip Tech1 Question: Won't start, fuel pump??

25 Page 25 of 41 WARNING: Replace the "O" ring seals exposed during component service in order to reduce the risk of fire and personal injury that may result from a fuel leak. Removal & Installation Loosen filler caps to relieve the fuel system pressure. Raise the vehicle. Disconnect the fuel pump harness connector. See Fig. 20. Clean both fuel pipe connections and surrounding areas at the fuel pump before disconnecting to avoid possible contamination of the fuel system. Disconnect both fuel pipes from the pump. Slide the pump out of the bracket. Cap the fuel pipes. To install, remove the caps from the fuel pipes. Install the new fuel pipe "O" rings. To complete installation, reverse removal procedure.

26 Page 26 of 41 Fig. 20: Locating Fuel Pump FUEL RAIL ASSEMBLY Removal & Installation (Right Bank) 1. Remove negative battery cable. Drain cooling system. Remove upper radiator hose and clamps. Remove bolt holding positive battery cable junction block and move out of way. Remove the turbo charged air outlet hose. Remove glow plug relay connectors and remove bracket.

27 Page 27 of Disconnect 24-pin and 40-pin engine connectors. Remove the engine connector bracket and set aside. Remove fuel pressure line, return line and "L" bracket. Remove Positive Crankcase Ventilation (PCV) line and set aside. Remove water pipe outlet at thermostat housing. Remove serpentine belt. Remove A/C compressor and position aside without disconnecting lines. Remove line from junction block to injector pump. Loosen and remove high pressure line at back end of fuel rail. Remove junction block. Loosen lines at injectors first and then loosen lines at fuel rail. Mark high pressure lines before removing for reference during installation. Remove 3 fuel rail bolts and remove fuel rail from vehicle. See Fig. 21. To install, reverse removal procedure. Removal & Installation (Left Bank) Disconnect the negative battery cables from both batteries. Drain the cooling system. Remove the air cleaner outlet duct. Remove the right side charged air outlet hose and clamps. Remove the Positive Crankcase Ventilation (PCV) hose and clamp. Remove the fuel injection control module. See FUEL INJECTION CONTROL MODULE. Remove the fuel filter. Remove the Exhaust Gas Recirculation (EGR) valve. See EGR VALVE. Disconnect the high pressure fuel rail line coming from the junction block. Loosen the high pressure injection lines at the four injectors. Loosen the high pressure lines injection at the four fittings on the fuel rail. Mark the high pressure injection lines in order and remove them. Remove the 3 bolts holding the fuel rail. See Fig. 21. To install, reverse removal procedure.

28 Page 28 of 41 Fig. 21: Locating Fuel Rail (Right Side Shown, Left Side Similar) FUEL RAIL PRESSURE SENSOR Removal Remove the Air Conditioning (A/C) compressor. See FUEL PRESSURE REGULATOR. Disconnect the fuel rail pressure sensor electrical connector. Remove the sensor and metal gasket from the junction block. Discard the gasket. See Fig. 22.

29 Page 29 of 41 Installation Install the sensor and a NEW metal gasket to the junction block. If a crows foot is used to torque the sensor then special attention to the position of the crows foot in relation to the torque wrench is required. If the crows foot is kept perpendicular (90 degrees) to the torque wrench during the entire tightening procedure, then the torque wrench can be set to the listed torque specification. See TORQUE SPECIFICATIONS. To complete installation, reverse removal procedure Fig. 22: Locating Fuel Rail Pressure Sensor FUEL RAIL TEMPERATURE SENSOR Removal & Installation

30 Page 30 of 41 Loosen the outlet duct clamp at the upper intake manifold cover. Remove the upper intake manifold cover from the outlet duct. Remove the upper intake manifold cover. Remove the turbo charged air outlet duct over the left valve cover. Remove the fuel temperature sensor harness connector. Remove the fuel temperature sensor from the fuel rail. See Fig. 23. To install, reverse removal procedure. Fig. 23: Locating Fuel Rail Temperature Sensor FUEL RETURN HOSE Removal & Installation 1. Disconnect the negative battery cable. Drain the cooling system. Remove the air cleaner outlet duct. Remove the right turbo charged air outlet hose. Remove the left turbo charged air outlet hose. Remove the engine wiring harness.

31 Page 31 of Remove the water outlet pipe. Remove the fuel hose from fuel return line. Remove the fuel hose from fuel injection pump and remove from engine. To install, reverse removal procedure. FUEL SYSTEM COOLER Removal & Installation (Cab & Chassis) Raise the vehicle. Disconnect the fuel pipes from the fuel cooler. See QUICK CONNECT FITTINGS (METAL COLLAR). Remove the retaining nuts from the chassis crossmember. Remove the fuel cooler. See Fig. 24. To install, reverse removal procedure. Fig. 24: Locating Fuel System Cooler (Cab & Chassis) Removal & Installation (Pickup)

32 Page 32 of 41 Raise the vehicle. Relieve the fuel pressure. Disconnect the fuel pipes from the fuel cooler. See QUICK CONNECT FITTINGS (METAL COLLAR). Remove the retaining bolts from the chassis and crossover. Remove the fuel cooler. Remove the fuel cooler support bracket from the fuel cooler. See Fig. 25. To install, reverse removal procedure.

33 Page 33 of 41 Fig. 25: Locating Fuel System Cooler (Pickup) FUEL TANK Removal & Installation (Cab & Chassis Auxiliary) Drain the fuel tank. Raise the vehicle. Remove the fuel tank shield. Disconnect the fuel fill and vent pipes from the fuel tank. Support the fuel tank, with the aid of an assistant. Remove the fuel tank strap attaching bolts. Remove the fuel tank straps. Lower the fuel tank slightly. Disconnect the fuel pipes from the fuel sender. See QUICK CONNECT FITTINGS (METAL COLLAR). Disconnect the fuel sender harness connector. Remove the fuel tank. Place the fuel tank in a suitable work area. Cap the fuel pipes in order to prevent possible fuel system contamination. To install, reverse removal procedure. Removal & Installation (Cab & Chassis Primary) Drain the fuel tank. Raise the vehicle. Remove the fuel tank shield. Disconnect the fuel fill and vent pipes from the fuel tank. Support the fuel tank, with the aid of an assistant. Remove the fuel tank strap attaching bolts. Remove the fuel tank straps. Lower the fuel tank slightly. Disconnect the fuel pipes from the fuel sender. See QUICK CONNECT FITTINGS (METAL COLLAR). If equipped with an auxiliary fuel tank disconnect the rear chassis balance pipes. Disconnect the fuel sender harness connector. Remove the fuel tank. Place the fuel tank in a suitable work area. Cap the fuel pipes on the vehicle in order to prevent possible fuel system contamination. To install, reverse removal procedure. Removal & Installation (Pickup) Drain the fuel tank. Raise the vehicle. Disconnect the fuel fill hose from the fuel tank. Remove the fuel system cooler. See FUEL SYSTEM COOLER. Disconnect the rear fuel return pipe and the rear fuel feed pipe at the chassis fuel pipes. See QUICK CONNECT FITTINGS (METAL COLLAR). Cap the fuel pipes in order to prevent possible fuel system contamination. Disconnect the fuel sender electrical connector. Remove the fuel tank shield. With the aid of an assistant, support the fuel tank. Remove the fuel tank strap attaching bolts. Remove the fuel tank straps. Remove the fuel tank. Place the fuel tank in a suitable work area. Remove the fuel feed pipe and the fuel return pipe from the fuel sender and the retaining clips. To install, reverse removal procedure. GLOW PLUG Removal & Installation NOTE: On the Federal Emissions systems there is a buss bar connecting the glow plugs on each bank of the engine.

34 Page 34 of 41 Disconnect the batteries. Remove the appropriate front wheel well. Remove the air cleaner outlet duct. Remove the electrical nuts from the desired glow plugs. Remove the harness from the desired glow plugs. Remove the desired glow plugs. To install, reverse removal procedure. Tighten glow plug to specification. See TORQUE SPECIFICATIONS. GLOW PLUG RELAY Removal & Installation (Calif.) Disconnect the negative battery cables. Loosen the outlet duct clamp at the upper intake manifold cover. Remove he upper intake manifold cover from the outlet duct. Remove the upper intake manifold cover. Remove the battery supply wiring harness nut and harness connector from the glow plug controller battery voltage supply post. Remove the glow plug wiring harness connectors from the glow plug controller. Remove the glow plug controller mounting bolt from the mounting bracket. Remove the glow plug controller from the mounting bracket. See Fig. 26. To install, reverse removal procedure.

35 Page 35 of 41

36 Page 36 of 41

37 Page 37 of 41 Fig. 26: Locating Glow Plug Relay (Calif.) Removal & Installation (Federal) Disconnect the negative battery cables. Loosen the outlet duct clamp at the upper intake manifold cover. Remove he upper intake manifold cover from the outlet duct. Remove the upper intake manifold cover. Remove the battery supply wiring harness nut and harness connector. Remove the glow plug wiring harness nuts and harness connectors. See Fig. 27. Release the wiring harness connectors at the glow plug relay. Remove the two glow plug relay mounting nuts. Remove the glow plug relay from the mounting studs. To install, reverse removal procedure.

38 Page 38 of 41 Fig. 27: Locating Glow Plug Relay (Federal) INTAKE AIR HEATER Removal & Installation

39 Page 39 of 41 Loosen the outlet duct clamp at the upper intake manifold cover. Remove he upper intake manifold cover from the outlet duct. Remove the upper intake manifold cover. Remove the intake air heater harness connector nut. Remove the intake air heater from the inlet pipe. See Fig. 28. To install, reverse removal procedure.

40 Page 40 of 41 Fig. 28: Locating Intake Air Heater MAF/IAT SENSOR Removal & Installation Disconnect the electrical connector of the Mass Air Flow/Intake Air Temperature (MAF/IAT) sensor. See Fig. 29. Remove the mounting bolts of the MAF/IAT sensor from the upper housing of the air cleaner assembly. Remove the MAF/IAT sensor. To install, reverse removal procedure. Fig. 29: Locating MAF/IAT Sensor

41 Page 41 of 41 PURGING FUEL SYSTEM Pump primer located on top of fuel filter 30 times or until stiff. Start engine and let idle. Check for leaks. QUICK CONNECT FITTINGS (METAL COLLAR) Removal Disconnect the negative battery cable. Remove the fuel filler cap. Remove the retainer from the quick -connect fitting. Blow dirt out of the fitting using compressed air. Choose the correct end of the fuel line disconnect tool for the size of the fitting. Insert the tool into the female connector, then push inward in order to release the locking tabs. Pull the connection apart. Use a clean shop towel in order to wipe off the male pipe end. Inspect both ends of the fitting for dirt and burrs. Clean or replace the components as required. Installation Apply a few drops of clean engine oil to the male pipe end. Push both sides of the fitting together in order to snap the retaining tabs into place. Once installed, pull on both sides of the fitting to ensure the connection is secure. Install the retainer to the quick-connect fitting. Install the fuel filler cap. Connect the negative battery cable. QUICK CONNECT FITTINGS (PLASTIC COLLAR) Removal Disconnect the negative battery cable. Remove fuel filler cap. Using compressed air, blow any dirt out of the quick-connect fitting. Squeeze the plastic retainer release tabs. Pull the connection apart. Installation Apply a few drops of clean engine oil to the male fuel pipe end. Push both sides of the quick-connect fitting together in order to cause the retaining tabs to snap into place. Once installed, pull on both sides of the quick-connect fitting to ensure the connection is secure. Install the fuel filler cap. Connect the negative battery cable Mitchell Repair Information Co., LLC.

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

Intake Manifold Replacement

Intake Manifold Replacement Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How 1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

2001 Lincoln LS Workshop Manual

2001 Lincoln LS Workshop Manual Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic 2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.

More information

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation. 1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit

2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit 2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is

More information

1992 Toyota Cressida

1992 Toyota Cressida Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May

More information

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

ARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR

ARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR Article Text Thursday, August 19, 1999 11:40PM ARTICLE BEGINNING 1996 ENGINE PERFORMANCE Volkswagen Removal, Overhaul & Installation - Gasoline Cabrio, Golf III, GTI, Jetta III, Passat CAUTION: When battery

More information

Cylinder head, removing and

Cylinder head, removing and Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder

More information

Engine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation

Engine Replacement Procedures September Removal of the Complete Powertrain Assembly. Replacement Long Block Engine Preparation 9 05-15 1 9 05-15 SUBJECT DATE Engine Replacement Procedures September 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the Complete Powertrain

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions

More information

Copper Sleeve, Unit Injector, Replacement

Copper Sleeve, Unit Injector, Replacement Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks

More information

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top

More information

Intake Manifold Replacement

Intake Manifold Replacement Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing

2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing 1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement

More information

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper) ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

1988 Ford F-350 PICKUP

1988 Ford F-350 PICKUP 1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are

More information

DISASSEMBLY AND REASSEMBLY

DISASSEMBLY AND REASSEMBLY 24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove 1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release

More information

DISASSEMBLY Procedure revision date: 11/22/2001

DISASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

INTAKE MANIFOLD INSPECTION/REPLACEMENT

INTAKE MANIFOLD INSPECTION/REPLACEMENT ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.

More information

Federal and California Emissions Warranties Parts List

Federal and California Emissions Warranties Parts List Emissions warranties are state specific. Refer to the years/miles 1 columns below as follows: A Minimum coverage for all vehicles in all states. B Vehicles registered and normally operated in California,

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

05-08 GT. Hellion Power Systems Mustang Kit Instructions

05-08 GT. Hellion Power Systems Mustang Kit Instructions Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo

More information

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages. 2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE

NUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE NUMBER: 10 01 12 S.M. REF.: Listed in Table ENGINE: EPA07 Series 60 DATE: October 2012 SUBJECT: REFERENCES TO THE TURBOCHARGER PURGE ROUTINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform

More information

Turbocharger Replacement

Turbocharger Replacement Page 1 of 11 2007 Chevrolet Silverado - 4WD Sierra, Silverado VIN C/K Service Manual Engine Engine Mechanical - 6.6L Repair Instructions - On Vehicle Document ID: 1872682 Turbocharger Replacement Removal

More information

ASSEMBLY/INSTALLATION INSTRUCTIONS

ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath

More information

Fuel Transfer Pump. OEM Part Numbers: , EP L. Fuel Transfer Pump. OEM Part Numbers: , EP

Fuel Transfer Pump. OEM Part Numbers: , EP L. Fuel Transfer Pump. OEM Part Numbers: , EP GM 6.5L Fuel System Components AP63440 Fuel Transfer Pump OEM Part Numbers: 25117340, EP309 1994 1999 6.5L AP63441 Fuel Transfer Pump OEM Part Numbers: 15754298, EP1000 1999 2002 6.5L Engine Components

More information

ASSEMBLY Procedure revision date: 11/22/2001

ASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

Page 1 of 6 2008 Ford Pickup 6.4L Eng F250 Super Duty ENGINE CONTROLS - DESCRIPTION AND OPERATION - F250-F550 SUPER DUTY 6.4L (DIESEL ) FUEL SYSTEM The fuel system includes the following: low pressure

More information

LChevrolet Camaro Supercharger Kit

LChevrolet Camaro Supercharger Kit PART #92000A Important Notes: 2010-2013 6.2LChevrolet Camaro Supercharger Kit The use of fuel additives (ie. octane boosters) is not recommended. There is a possibility that these chemicals can damage

More information

Installation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L

Installation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L 12/13/11 ATS Twin CP3 Kit 701-900-2272-INST Installation Manual v2.2: Twin CP3 Fuel Injection Kit 2003-2004 Dodge 5.9L Figure 1 - Full Kit Photo 26 Figure 2 - Hardware Kit 1 Please read all instructions

More information

REMOVAL. Fig Sized for Print

REMOVAL. Fig Sized for Print ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting

More information

The following tools will be required to perform this new service procedure outlined in this bulletin:

The following tools will be required to perform this new service procedure outlined in this bulletin: The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

SECTION C Engine 6.4L Diesel

SECTION C Engine 6.4L Diesel 303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft

More information

This information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.

This information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine. Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773

More information

2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body.

2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body. 2002 Silverado K 4WD Applies to: 4.8L, 5.3L, and 6.0L Report a problem with this article Removal Procedure 1. Remove the air intake duct. Refer to Air Cleaner Resonator Outlet Duct Replacement. 2. Disconnect

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST 1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions

More information

2003 F-Super Duty /Excursion Workshop Manual

2003 F-Super Duty /Excursion Workshop Manual Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

BEFORE BEGINNING INSTALLATION

BEFORE BEGINNING INSTALLATION COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L 04/05/2012 Dodge 2010-2011 6.7L Twin CP3 701-900-2356-INST Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2010-2011 Dodge 6.7L Figure 1 - Full Kit Photo 29 Figure 2 - Hardware Kit (800) 949-60002

More information

2011 Mercury Grand Marquis LS

2011 Mercury Grand Marquis LS Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.

More information

Cylinder head/gasket, replacing

Cylinder head/gasket, replacing 1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations

More information

Engine Dismantle and Assemble ( )

Engine Dismantle and Assemble ( ) Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer

More information

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #

2006 Honda Civic SI Supercharger Kit Installation Instruction Kit # 2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009

More information

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07 26770_U07.qxd 8/30/05 3:01 PM Page 8 7-8 06025-S10P-C07 06025-S10P-C08 26770_U07.qxd 8/30/05 3:01 PM Page 9 7-9 06025-S10P-C09 26770_U07.qxd 8/30/05 3:01 PM Page 10 7-10 06025-S10P-C10 26770_U07.qxd 8/30/05

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

PRECAUTIONS ENGINE REPAIR

PRECAUTIONS ENGINE REPAIR 3234_U01.qxd 9/23/03 3:44 PM Page 13 BLAZER XTREME TRAILBLAZER BRAVADA ENVOY JIMMY 1-13 PRECAUTIONS Before servicing any vehicle, please be sure to read all of the following precautions, which deal with

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information

SLP Camaro ZL1 STAGE 3 (650 HP)

SLP Camaro ZL1 STAGE 3 (650 HP) SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

Solenoid Valve VCB, Replacement, D13F. This information covers the procedures for replacing the VCB solenoid valve on the Volvo D13F engine.

Solenoid Valve VCB, Replacement, D13F. This information covers the procedures for replacing the VCB solenoid valve on the Volvo D13F engine. Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 10.2007 253 67 1(9) Solenoid Valve VCB, Replacement D13F Solenoid Valve VCB, Replacement, D13F This information

More information

Intake Manifold: Service and Repair Removal

Intake Manifold: Service and Repair Removal 1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling

More information

Included parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe

Included parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

Installation Instructions Part Number

Installation Instructions Part Number Installation Instructions Part Number 84152143 Thank you for choosing Chevrolet Performance as your high performance source. Chevrolet is committed to providing proven, innovative performance technology

More information

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace

More information

2014+ Ram 3.0 EcoDiesel EGR Delete

2014+ Ram 3.0 EcoDiesel EGR Delete 2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD

More information

Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft

More information

2000 Chrysler SEBRING

2000 Chrysler SEBRING 2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a

More information