1999 Villager Workshop Manual

Size: px
Start display at page:

Download "1999 Villager Workshop Manual"

Transcription

1 Page 1 of 5 SECTION : Engine Cooling 1999 Villager Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/27/1998 Cooling System Draining, Filling And Bleeding Draining WARNING: Do not open the cooling system while it is hot or engine is running. CAUTION: The coolant must be recovered in a suitable, clean container for reuse. If the coolant is contaminated it must be recycled or disposed of correctly. 1. WARNING: Never remove the radiator cap under any conditions while the engine is operating. Failure to follow these instructions could result in damage to the cooling system or engine and/or personal injury. To avoid having scalding hot coolant or steam blow out of the radiator use extreme care when removing the radiator cap from a hot radiator. Wait until the engine has cooled, then wrap a thick cloth around the radiator cap and turn it slowly to the first stop. Step back while the pressure is released from the cooling system. When it is certain all the pressure has been released, press down on the cap (still with a cloth), turn and remove. Allow the engine to cool and remove the radiator cap. 2. Raise and support the vehicle. 3. Remove the engine splash shield. 4. Place a suitable container below the radiator draincock. If so equipped, disconnect the coolant return hose at the oil cooler. 5. Open the radiator draincock. 6. Remove the LH cylinder block drain plug to drain the coolant from the cylinder block. 7. Remove the RH cylinder block drain plug to drain the coolant from the cylinder block. 8. Remove and clean the coolant expansion tank. 1. Remove the bolts. 2. Remove and clean the coolant expansion tank.

2 Page 2 of 5 9. Install the coolant expansion tank. 1. Position the coolant expansion tank. 2. Install the bolts. 10. Remove the engine air relief plug. 11. When the coolant is drained, install the LH drain plug. 12. Install the RH drain plug. 13. Close the radiator draincock. 14. Lower the vehicle. Filling and Bleeding 1. NOTE: When filler neck is full, gently move upper radiator hose up and down while filling until coolant no longer lowers in the filler neck. Slowly fill the radiator with the correct 50/50 mixture of Premium Cooling System Fluid E2FZ AA or equivalent meeting Ford specification ESE-M97B44-A until coolant fills the radiator filler neck. 2. Insert a wire under the negative pressure valve of the radiator cap.

3 Page 3 of 5 3. Install the radiator cap. 4. Disconnect the coolant expansion tank tube from the radiator. 5. Hang a one gallon modified bottle above the engine air relief hole and connect a suitable tube from it to the coolant expansion tank tube port on the radiator. Clamp the tube to prevent coolant flow though the tube and fill the modified bottle with the correct 50/50 mixture of Premium Cooling System Fluid E2FZ AA or equivalent meeting Ford specification ESE-M97B44-A and water. 6. Unclamp the tube used with the modified bottle and allow coolant to flow until coolant comes out of the engine air relief hole, then reclamp tube. 7. Install the engine air relief plug.

4 Page 4 of 5 8. Raise and support the vehicle using a suitable supporting device. 9. Set the heater controls to full warm and blower to high. 10. Unclamp the tube used with the modified bottle. 11. Start the engine and maintain 1500 RPM until the cooling fan turns on. 12. Turn the engine off and let the engine cool off completely. 13. Remove the supporting device and lower the vehicle. 14. Clamp the tube used with the modified bottle. 15. Remove the modified one gallon bottle and tube. 16. Connect the coolant expansion tank tube to the radiator. 17. WARNING: Never remove the radiator cap under any conditions while the engine is operating. Failure to follow these instructions could result in damage to the cooling system or engine and/or personal injury. To avoid having scalding hot coolant or steam blow out of the radiator use extreme care when removing the radiator cap from a hot radiator. Wait until the engine has cooled, then wrap a thick cloth around the radiator cap and turn it slowly to the first stop. Step back while the pressure is released from the cooling system. When it is certain all the pressure has been released, press down on the cap (still with a cloth), turn and remove.

5 Page 5 of 5 Allow the engine to cool and remove the radiator cap. 18. Remove the wire from the radiator cap. 19. Completely fill the radiator with the correct 50/50 mixture of Premium Cooling System Fluid E2FZ AA or equivalent meeting Ford specification ESE-M97B44-A and water. 20. Fill the coolant expansion tank to the MAX mark. 21. Install the radiator cap.

THERMOSTAT - 3.5L NA V8 - AJV8/V8 4.2L PETROL (G239859)

THERMOSTAT - 3.5L NA V8 - AJV8/V8 4.2L PETROL (G239859) PUBLISHED: 11-MAY-2011 2003.50 XJ RANGE (X350), 303-03 ENGINE COOLING - 3.0L NA V6 - AJ27/3.5L NA V8 - AJV8/V8 4.2L PETROL/V8 S/C 4.2L PETROL - 3.5L NA V8 - AJV8/V8 4.2L PETROL (G239859) REMOVAL AND INSTALLATION

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

2012 Mustang Workshop Manual. 14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator.

2012 Mustang Workshop Manual. 14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator. 14. Position the lower radiator hose assembly into the vehicle. Connect the lower radiator hose to the radiator. 15. Connect the coolant hose to the oil cooler. 16. Rotate the SC drive belt tensioner clockwise

More information

SECTION A Engine Cooling

SECTION A Engine Cooling 303-03A-i Engine Cooling 303-03A-i SECTION 303-03A Engine Cooling CONTENTS PAGE DESCRIPTION AND OPERATION Engine Cooling... 303-03A-2 Coolant Flow Diagram... 303-03A-3 303-03A-2 Engine Cooling 303-03A-2

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 303-03-1 Engine Cooling 303-03-1 REMOVAL AND INSTALLATION Radiator, Cooling Fan and Shroud Special Tool(s) Wrench, Fan Clutch Nut 303-240 (T84T-6312-D) Holding Wrench, Fan Pulley 303-239 (T84T-6312-C)

More information

FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L

FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L 2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST

More information

M-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS

M-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS !!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!

More information

Crown Victoria, Grand Marquis and Lincoln Town Car Engine Oil Cooler Replacement

Crown Victoria, Grand Marquis and Lincoln Town Car Engine Oil Cooler Replacement ATTACHMENT III Owner Notification Program 96B86 Crown Victoria, Grand Marquis and Lincoln Town Car Engine Oil Cooler Replacement Affected Vehicles: 1994 And 1995 Crown Victoria Police Interceptor. 1995

More information

RADIATOR CLEANING OF RADIATOR

RADIATOR CLEANING OF RADIATOR CO20 COOLING SYSTEM RADIATOR CLEANING OF RADIATOR Using water or a steam cleaner, remove any mud and dirt from the radiator core. CAUTION: If using a high pressure type cleaner, be careful not to deform

More information

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.

1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation. TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan

More information

This Field Service Action expired on January 31, 2001.

This Field Service Action expired on January 31, 2001. This Field Service Action expired on January 31, 2001. OWNER NOTIFICATION PROGRAM 99B28 Certain 1999 & 2000 Model Year F-250 Super Duty Through F-550 Super Duty, 1999 F-Super Duty Stripped Chassis & 1999

More information

Drained coolant must be stored in a clean container for disposal or reuse.

Drained coolant must be stored in a clean container for disposal or reuse. Cooling System, Draining and Filling Special tools, testers and auxiliary items required Adapter (V.A.G 1274/8) Adapter V.A.G 1274 tester (V.A.G 1274/10) Hose clamp pliers (V.A.G 1921) Cooling system charge

More information

Applicable vehicles: 2007 Ford Fusion 2007 Ford Milan 2007 Ford MKZ. DIAGNOSIS AND TESTING Procedure revision date: 11/17/2006

Applicable vehicles: 2007 Ford Fusion 2007 Ford Milan 2007 Ford MKZ. DIAGNOSIS AND TESTING Procedure revision date: 11/17/2006 PATH: Diagnostics > Diagnostic Routines > Powertrain > Engine > Engine Cooling Engine Cooling NOTE Applicable vehicles: 2007 Ford Fusion 2007 Ford Milan 2007 Ford MKZ SECTION 303-03: Engine Cooling 2007

More information

CO01 Radiator Assembly

CO01 Radiator Assembly Uniform Procedures For Collision Repair CO01 Radiator Assembly 1. Description This procedure describes methods for the removal and installation of a radiator assembly. Inspection and evaluation requirements

More information

Steps 3 through 9 in this procedure describe making and using a cooling system bleed tool.

Steps 3 through 9 in this procedure describe making and using a cooling system bleed tool. Cooling System Bleed Procedure Steps 3 through 9 in this procedure describe making and using a cooling system bleed tool. However, you can use a commercially available funnel-type coolant refill bleed

More information

ALLDATA Online Buick Truck Rendezvous V6-3.4L VIN E - Draining and Fillin... Draining and Filling Cooling System

ALLDATA Online Buick Truck Rendezvous V6-3.4L VIN E - Draining and Fillin... Draining and Filling Cooling System Page 1 of 8 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Buick Truck Rendezvous V6-3.4L VIN E Conversion Calculator Vehicle

More information

Draining and Filling Cooling System

Draining and Filling Cooling System 2000 GMC Truck Sonoma Pickup - 2WD Draining and Filling Cooling System Engine Coolant Recycling The use of a waterless, GM approved coolant recycling system on the vehicle eliminates the need for evacuation.

More information

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove 1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

Draining and Filling Cooling System

Draining and Filling Cooling System 1996 Chevrolet/Geo Monte Carlo Draining and Filling Cooling System Correct Fill Ratios 1. Ethylene glycol/water fill ratios have been established to ensure a minimum of 50 percent ethylene glycol in the

More information

2014 RAM C/V Tradesman

2014 RAM C/V Tradesman Fig. 91: Suction Hose Ball Valve NOTE: View typical 14. Open the suction hose's ball valve to begin refilling the cooling system. 15. When the vacuum gauge reads zero, the system is filled. NOTE: On some

More information

Engine Oil, Cooling System

Engine Oil, Cooling System Engine Oil, Cooling System OIL FILTER 6. Refill the engine with the recommended oil. Engine oil change capacity (including filter): () 4.4 US qt (4.2 ) () 4.5 US qt (4.3 ) 7. Replace the engine oil fill

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

2002 Jeep Grand Cherokee Laredo

2002 Jeep Grand Cherokee Laredo Removal WARNING: DO NOT REMOVE THE CYLINDER BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR. REFER TO COOLING SYSTEM DRAINING.

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31

More information

Information on Aluminum Heater Core and/or Radiator Replacement # (Feb 24, 2005)

Information on Aluminum Heater Core and/or Radiator Replacement # (Feb 24, 2005) Document ID# 1614922 2004 Cadillac CTS Information on Aluminum Heater Core and/or Radiator Replacement #05-06-02-001 - (Feb 24, 2005) Information On Aluminum Heater Core and/or Radiator Replacement 2005

More information

Antifreeze Type SYC1025 (Long life coolant) Mixing ratio (water:antifreeze) Cooling fan module Type Electric Capacity

Antifreeze Type SYC1025 (Long life coolant) Mixing ratio (water:antifreeze) Cooling fan module Type Electric Capacity 152000 083 1. SPECIFICATION Unit Description Specification Cooling system Type Water cooling, forced circulation Coolant Capacity approx. 8.5 L Radiator Core size 555W x 582.4H x 27T (over 326,250mm2)

More information

2004 F-150 Workshop Manual

2004 F-150 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047

More information

2004 Lincoln LS Workshop Manual

2004 Lincoln LS Workshop Manual SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. Engine Control Module (ECM) I/O Signal A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9

More information

Filling coolant WARNING!

Filling coolant WARNING! Working on the vehicle cooling system Working on the vehicle cooling system WARNING! When making modifications to the cooling system, the cooling system must be emptied, refilled and pressure tested. The

More information

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine 2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,

More information

INSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.

INSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block. 303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.

More information

COMPONENT LOCATION INDEX

COMPONENT LOCATION INDEX COMPONENT LOCATION INDEX 2011-12 ENGINE Cooling System - TSX V6 Fig. 1: Identifying Cooling System Components RADIATOR CAP TEST 2. Wait until the engine is cool, then carefully remove the radiator cap

More information

26 - COOLING SYSTEM CONTENTS ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 COOLING SYSTEM FAULTS... 1

26 - COOLING SYSTEM CONTENTS ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 COOLING SYSTEM FAULTS... 1 26 - COOLING SYSTEM CONTENTS Page LAND ROVER V8 DESCRIPTION AND OPERATION ENGINE COOLING - DESCRIPTION... 3 ENGINE COOLING - OPERATION... 9 FAULT DIAGNOSIS COOLING SYSTEM FAULTS... 1 REPAIR COOLANT - DRAIN

More information

2002 Taurus/Sable Workshop Manual

2002 Taurus/Sable Workshop Manual SECTION 211-02: Power Steering REMOVAL AND INSTALLATION 2002 Taurus/Sable Workshop Manual Power Steering Pump Pulley CII Pump Special Tool(s) Installer, Power Steering Pump Pulley 211-009 (T65P-3A733-C)

More information

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1 Radiator Cap Tester 2AZ-FE OLING OLING SYSTEM A112194E01 A112306 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK OLING SYSTEM FOR LEAKS (a) Remove the radiator reservoir cap. CAUTION: To avoid the danger

More information

BHW Engine Coolant Temperature Replacement

BHW Engine Coolant Temperature Replacement BHW Engine Coolant Temperature Replacement NEVER perform this procedure on a hot engine. Parts: 059 919 501 A dual temperature sensor 032 121 142 retaining spring N 903 168 02 sensor round seal N 905 216

More information

1 of 14 11/19/ :45 AM

1 of 14 11/19/ :45 AM 1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.

More information

Draining and Filling Cooling System

Draining and Filling Cooling System 1998 Chevrolet/Geo Cavalier Draining and Filling Cooling System Glycol Usage Before you drain and refill the cooling system, inspect the system. Perform any service needed to ensure that the system is

More information

Page 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C

More information

ALTIMA; POOR HEATER PERFORMANCE

ALTIMA; POOR HEATER PERFORMANCE Classification: Reference: Date: HA02-002b NTB02-047b September 9, 2003 2002 2003 ALTIMA; POOR HEATER PERFORMANCE This bulletin amends NTB02-047a. This version updates the Service Procedure. Please discard

More information

Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate

More information

SLP Camaro ZL1 STAGE 2 (625 HP)

SLP Camaro ZL1 STAGE 2 (625 HP) SLP - 2012 Camaro ZL1 STAGE 2 (625 HP) PART #26001 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

ENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT

ENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT 14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM ENGINE COOLING SYSTEM B ENGINE SECTION CO A ENGINE COOLING SYSTEM CO C D CONTENTS E QR PRECAUTIONS... 3 Precautions for Liquid Gasket... 3 LIQUID GASKET APPLICATION PROCEDURE... 3 PREPARATION... 4 Special

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION...

More information

INSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.

INSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block. 303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

2003 Escape Workshop Manual

2003 Escape Workshop Manual Page 1 of 6 SECTION 211-02: Power Steering 2003 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/06/2005 Steering Gear Printable View (633 KB) Special Tool(s) Tie-Rod End Remover

More information

Page 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION...

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

DIAGNOSIS MADE EASY PART OF COOLING SYSTEM TROUBLE SHOOTING

DIAGNOSIS MADE EASY PART OF COOLING SYSTEM TROUBLE SHOOTING DIAGNOSIS MADE EASY PART OF COOLING SYSTEM TROUBLE SHOOTING DIAGNOSE CAR PROBLEMS QUICKLY AND RELIABLY USING GATES INTUITIVE QUESTION TREE DIAGNOSTIC PROCESS The purpose of this booklet is to provide

More information

Additions, Revisions, or Updates

Additions, Revisions, or Updates 03 06-18 1 03 06-18 SUBJECT DATE Flushing the Engine Lubrication System March 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change EPA07/ DDC-SVC-MAN-0081 EPA10/

More information

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref... Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight

More information

SECTION : a Engine Cooling

SECTION : a Engine Cooling 303-03a Engine Cooling 303-03a SECTION : 303-03a Engine Cooling VEHICLE APPLICATION : 2006.0 BF Falcon CONTENTS SPECIFICATIONS PAGE Specifications...303-03a-1 DESCRIPTION AND OPERATION Engine Cooling...303-03a-3

More information

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section

1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine

More information

Draining and Filling Cooling System

Draining and Filling Cooling System 1998 Oldsmobile Intrigue Draining and Filling Cooling System Caution As long as there is pressure in the cooling system, the temperature can be considerably higher than the boiling temperature of the solution

More information

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT)

Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets

More information

GROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS...

GROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS... 14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOL 14-2 ENGINE COOLING DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE

More information

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane

Engine Remove and Install ( ) Remove. 2,5l TCI Diesel Engine. Special Tools. Workshop Equipment Transmission jack Trolley jack Workshop crane Engine Remove and Install ( 34 0) Special Tools 068 A 068A Engine lifting tackle 4 003 Coolant hose clamp removal and fitting tool Workshop Equipment Transmission jack Trolley jack Workshop crane Materials

More information

ENGINE COOLING 14-1 CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 LUBRICANT... 2 SEALANT... 2 THERMOSTAT SPECIAL TOOLS...

ENGINE COOLING 14-1 CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 LUBRICANT... 2 SEALANT... 2 THERMOSTAT SPECIAL TOOLS... 14-1 EINE COOLI CONTENTS GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 LUBRICANT... 2 SEALANT... 2 SPECIAL TOOLS... 3 TROUBLESHOOTI... 3 ON-VEHICLE SERVICE... 6 Engine Coolant Leak Checking... 6

More information

CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR

CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR COOLANT COOLANT INSPECTION HINT: Check the coolant level when the engine is cold. 1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR The engine coolant level should be between the LOW and FULL lines at

More information

Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.

More information

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent 303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent

More information

COOLING SYSTEM Return To Main Table of Contents

COOLING SYSTEM Return To Main Table of Contents COOLING SYSTEM Return To Main Table of Contents GENERAL.............................................. 2 COOLING SYSTEM........................................... 7 RADIATOR... 8 RADIATOR FAN MOTOR ASSEMBLY...

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor

More information

AR20.00-P-1142HA Drain/pour in coolant

AR20.00-P-1142HA Drain/pour in coolant R20.00-P-1142H Drain/pour in coolant 20.10.15 Engine 112 in model 129, 202, 208, 210, 211.061/065/080/082/261/265/280/282, 220, Engine 112 in model 163 Engine 113 in model 163 Shown on MODEL 202 1 Coolant

More information

WOC-364 Installation Instructions Ranger XP Heater System

WOC-364 Installation Instructions Ranger XP Heater System WOC-364 Installation Instructions Ranger 2011-12 XP Heater System Order of installation for a Complete Enclosure Always install the Heater System first if possible NOTE: If installing the Heater System

More information

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION

EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be

More information

S T i P E R F O R M A N C E R A D I A T O R H O S E I N S T R U C T I O N S Thank you for your purchase of SPT Performance Parts. The following instructions have been provided to you as a courtesy of Subaru

More information

GENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench

GENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench 206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent

More information

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B 5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal

More information

EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT

EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT External Oil Filter with Coolant Filter Kit PACKING LIST: QTY. 4 4 Description Oil Filter Coolant Filter Small Brass 90 Fitting Large Brass 90 Fitting

More information

IN-VEHICLE SERVICE. Engine Components

IN-VEHICLE SERVICE. Engine Components file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM ENGINE SECTION CO A ENGINE COOLING SYSTEM CO C D CONTENTS E VQ35DE PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precaution

More information

2014+ FORD FIESTA ST DIRECT-FIT OIL COOLER KIT PARTS LIST AND INSTALLATION GUIDE CAUTION PARTS INCLUDED NOTE TOOLS NEEDED INSTALL PROCEDURE

2014+ FORD FIESTA ST DIRECT-FIT OIL COOLER KIT PARTS LIST AND INSTALLATION GUIDE CAUTION PARTS INCLUDED NOTE TOOLS NEEDED INSTALL PROCEDURE PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS & SPACER 1PC 19-ROW OIL COOLER 1PC 4 ', X 1'' BRAIDED HOSE W/90-10AN FITTINGS 1PC 3'' X 2.5 '' BRAIDED HOSE W/45 AND 90-10AN FITTINGS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ENGINE BLOCK P/N 08T44-SJA-200 2008 FIT AII 37494 Issue Date JUL 2007 PARTS LIST Engine block heater Aluminum washer Heater harness Protective

More information

2000 Ranger Workshop Manual

2000 Ranger Workshop Manual SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)

More information

RED ALPHA COOLANT EXPANSION TANK

RED ALPHA COOLANT EXPANSION TANK RED ALPHA COOLANT EXPANSION TANK Our Q60 and Q50 VR30 Red Alpha Expansion Tank increases the Red Alpha Heat Exchanger coolant capacity by an astounding 70% and the radiator coolant capacity by 28%! Our

More information

ENGINE SPECIFICATIONS

ENGINE SPECIFICATIONS ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)

More information

FUEL SUPPLY Click on the applicable bookmark to selected the required model year

FUEL SUPPLY Click on the applicable bookmark to selected the required model year FUEL SUPPLY F- FUEL SUPPLY CONTENTS 0000 GENERAL INFORMATION................ FUEL TANK............................. FUEL FILTER ......................................... 6 F- FUEL

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM ENGINE SECTION CO A ENGINE COOLING SYSTEM CO C D CONTENTS E QR25DE PRECAUTION... 3 PRECAUTIONS... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...3 Necessary

More information

Superduty 6.0L Powerstroke Engine Removal/Installation Service Tips

Superduty 6.0L Powerstroke Engine Removal/Installation Service Tips Superduty 6.0L Powerstroke Engine Removal/Installation Service Tips May 2004 Continue TABLE OF CONTENTS Shop Manual Procedure The procedure steps must be followed in a specific order. Turbo Marmon Clamp

More information

ENGINE LUBRICATION & COOLING SYSTEMS SECTIONLC CONTENTS. ENGINE LUBRICATION SYSTEM...2 Precautions...2

ENGINE LUBRICATION & COOLING SYSTEMS SECTIONLC CONTENTS. ENGINE LUBRICATION SYSTEM...2 Precautions...2 ENGINE LUBRICATION & COOLING SYSTEMS SECTIONLC CONTENTS ENGINE LUBRICATION SYSTEM...2 Precautions...2 LIQUID GASKET APPLICATION PROCEDURE...2 Preparation...2 SPECIAL SERVICE TOOLS...2 Lubrication Circuit...3

More information

DIM Heating and Air Conditioning

DIM Heating and Air Conditioning 2014 NATEF JOB TASKS COMPLETION REQUIREMENT: P1-95% P2-70% P3-25% Student Name: DETAILED COURSE CONTENT VI. HEATING, VENTILATION, & AIR CONDITIONING A. HVAC SYSTEMS -- The student will be able to: P1 P2

More information

Cooling system Type Water cooling, forced circulation Coolant Capacity Approx. 8.0 ~ 8.5 L

Cooling system Type Water cooling, forced circulation Coolant Capacity Approx. 8.0 ~ 8.5 L 211201 083 1. SPECIFICATION Description Specification Cooling system Type Water cooling, forced circulation Coolant Capacity Approx. 8.0 ~ 8.5 L Radiator Core size 740W X 378.9H X 27T Flow type Cross flow

More information

1998 F-150/250 Workshop Manual

1998 F-150/250 Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco

More information

ENGINE COOLING SYSTEM

ENGINE COOLING SYSTEM ENGINE SECTION CO A ENGINE COOLING SYSTEM CO C D CONTENTS E VQ35DE Changing Engine Coolant...11 F PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT

More information

SLP Camaro ZL1 STAGE 3 (650 HP)

SLP Camaro ZL1 STAGE 3 (650 HP) SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

ENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT...

ENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT... 14-1 GROUP 14 CONTENTS GENERAL INFORMATION 14-2 SERVICE SPECIFICATIONS 14-2 COOLANT 14-3 SEALANT 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES

More information

This Service Bulletin replaces SB , Cooling System Service, dated (1.2007), publication no. PV Cooling System, Pressure Test

This Service Bulletin replaces SB , Cooling System Service, dated (1.2007), publication no. PV Cooling System, Pressure Test Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces SB 260-32, Cooling System Service, dated (1.2007), publication no. PV776 20177193. Cooling System, Pressure Test DService Bulletin

More information

ENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT...

ENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT... 14-1 GROUP 14 CONTENTS GENERAL INFORMATION 14-2 SERVICE SPECIFICATIONS 14-2 COOLANT 14-3 SEALANT 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

ENGINE COOLING SYSTEM GENERAL 1. GENERAL SPECIFICATIONS ENGINE COOLING SYSTEM. undefined

ENGINE COOLING SYSTEM GENERAL 1. GENERAL SPECIFICATIONS ENGINE COOLING SYSTEM. undefined 211001 043 GENERAL 1. GENERAL SPECIFICATIONS 211001 044 211001 2. FASTENER TIGHTENING SPECIFICATIONS 211001 045 OVERVIEW AND OPERATION PROCESS 1. COMPONENT LOCATOR 1. Reserver Tank 2. Deaeration Tube 3.

More information

INSTALLATION INSTRUCTIONS COOLANT EXPANSION TANK

INSTALLATION INSTRUCTIONS COOLANT EXPANSION TANK INSTALLATION INSTRUCTIONS COOLANT EXPANSION TANK 2011+ FORD MUSTANG Document: 19-0147 Support: info@radiumauto.com Steps below show installation in a 2015+ Ford Mustang (P/N: 20-0286) The same procedure

More information

5. Engine Control Module (ECM) I/O Signal S008526

5. Engine Control Module (ECM) I/O Signal S008526 5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen

More information