2000 Chrysler SEBRING

Size: px
Start display at page:

Download "2000 Chrysler SEBRING"

Transcription

1 2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a molded plastic composition. It is attached to the cylinder head with 10 fasteners. Please note that all seals are to be replaced with new seals and all fasteners are to be replaced with new fasteners. Obtain the necessary parts before beginning work. The intake manifold for the 2.4L DOHC engine is a long branch design made of cast aluminum. It is attached to the cylinder head with 8 fasteners. 1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding. Fuel injection systems remain under pressure after the engine has been turned OFF. The fuel system pressure MUST be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury. 2. Properly relieve the fuel system pressure using the procedure outlined in Section Remove the air inlet resonator as follows: A. On the 2.4L DOHC engine only, remove the 2 mounting bolts that secure the air inlet resonator to the intake manifold. B. Loosen the screw securing the air inlet resonator to the throttle body. C. Loosen the clamp securing the air inlet resonator to the air inlet tube. Remove the resonator. 4. Disconnect the fuel supply line quick-connect fitting from the fuel rail by squeezing the retainer tabs together and pulling the fuel tube/quick-connect fitting from the fuel tube nipple. The retainer will remain on the fuel tube. Wrap shop towels around the fuel line openings to catch any spilling fuel. 5. Remove the fuel rail attaching screws and remove the fuel rail. Use care when handling the fuel injectors. Do not set them on their tips. Cover the fuel injector openings after fuel rail removal. 6. Remove the accelerator, kickdown and speed control cables from the throttle lever and bracket. 7. Disengage the Throttle Position Sensor (TPS) and the Idle Air Control (IAC) motor electrical connections. 8. Disconnect the vacuum hoses from the throttle body. 9. Disengage the connectors from the Manifold Absolute Pressure (MAP) sensor and the intake air temperature sensors. 10. Disconnect the vapor and brake booster hoses. 11. Disengage the knock sensor electrical connector, starter relay connector (if necessary), and the wiring harness from the tab located on the intake manifold. 12. Remove the transaxle to throttle body support bracket fasteners at the throttle body and loosen the fastener at the transaxle end. 13. Remove the throttle body assembly as outlined in Section Remove the EGR tube bolts at the valve and at the intake manifold. Remove the tube from the engine. 15. Remove the intake manifold-to-inlet water tube support fastener (2.0L) or intake manifold support bracket (2.4L). 16. Remove the intake manifold fasteners and washer assemblies. On the 2.0L engine, discard the fasteners and, during assembly, replace them with new fasteners. 17. Remove the intake manifold from the vehicle. To install: 18. Clean all gasket sealing surfaces. Check the upper and lower manifold gasket surfaces for cracks or distortion. Fig. 1: Make sure that the intake manifold O-ring gaskets are properly seated 2.0L SOHC engine Fig. 2: Intake manifold tightening sequence 2.0L SOHC engine

2 Fig. 3: Intake manifold tightening sequence 2.4L DOHC engine 19. For the 2.0L engine, install the intake manifold with new O-ring seals. For the 2.4L engine, install a new intake manifold gasket and position the manifold on the cylinder head. Tighten the fasteners to 105 inch lbs. (12 Nm) in correct sequence, starting from the center and working outward. 20. Remove the covers from the fuel injector openings and install the fuel injectors into the engine. Seat the injectors in place and tighten the fuel rail bolts to 200 inch lbs. (23 Nm). 21. Connect the PCV and brake booster hoses. 22. Inspect the quick-connect fittings for damage and repair as required. Lubricate the fuel line with clean 30W engine oil. Reconnect the fuel supply line hose to the fuel rail assembly. Check the connection by pulling on the connector to insure it is locked in position. 23. Engage the electrical connectors to the fuel injectors. 24. Install the throttle body and tighten to 200 inch lbs. (23 Nm). Reinstall the transaxle to throttle body support bracket and tighten to 105 inch lbs. (12 Nm) at the throttle body first. Next, tighten the bracket at the transaxle. 25. Engage the MAP sensor and the air temperature sensor wiring connectors. 26. Engage the knock sensor electrical and starter relay connectors. Reconnect the wiring harness to the intake manifold tab. 27. Engage the IAC and TPS wiring connectors. 28. Reconnect the throttle body vacuum hoses. 29. Install the accelerator, kickdown and speed control cables to their bracket, then connect them to the throttle lever. 30. Loosely assemble the EGR tube onto the valve and intake manifold finger-tight. Tighten the tube fasteners at the EGR valve first to 95 inch lbs. (11 Nm), then tighten the intake manifold side fasteners to 95 inch lbs. (11 Nm). 31. Install the air inlet resonator to the throttle body. Connect the air inlet tube to the resonator and tighten the clamps to inch lbs. (2 3 Nm). 32. Connect the negative battery cable. Pressurize the fuel system using the DRB Scan Tool, or equivalent. Perform the ASD Fuel System Test and check for leaks. 2.0L DOHC Engine This engine uses a two-piece aluminum intake manifold. The upper half of the manifold (also called a plenum) mounts the throttle body. The lower half of the manifold contains the fuel rail and injectors. A non-reusable gasket joins the two halves. Use care when working with light alloy parts. Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury. 1. Relieve the fuel system pressure. 2. Disconnect the negative battery cable and drain the cooling system. 3. Disconnect the accelerator cable, breather hose and air intake hose. 4. Disengage the vacuum connection at the power brake booster and the PCV valve. Disconnect all remaining vacuum hoses and pipes, as necessary. Tag for identification, if necessary, to save time at assembly. 5. Disconnect the fuel line(s), then remove the throttle control cable and brackets. Do not use conventional fuel filters, hoses or clamps when servicing fuel injection systems. They are not compatible with the injection system and could fail, causing personal injury or damage to the vehicle. Use only hoses and clamps specifically designed for fuel injection. 6. Unplug the alternator wiring harness connection. 7. Disengage the MAP sensor and the intake air temperature sensor connectors. 8. Disengage the TPS connector and position the engine wiring harness aside. 9. Disengage the EGR pipe connection. 10. Remove the intake manifold stay and the engine hanger. Disengage the fuel injector connectors. 11. Remove the throttle body assembly as outlined in Section Unfasten the mounting bolts and remove the intake manifold plenum and gasket. 13. Remove the complete fuel rail assembly. Use care since the fuel injectors can drop out of the fuel rail as it is being removed. 14. Remove the mounting bolts, then remove the intake manifold and gasket from the engine. Fig. 4: Intake manifold assembly 2.0L DOHC engine

3 To install: 15. Clean all gasket material from the cylinder head and intake manifold assembly. Check both surfaces for cracks or other damage. Check the intake manifold water passages and air passages for clogging. Clean if necessary. Check the gasket surface of the intake manifold for flatness using a straightedge and feeler gauge. It should be inch (0.152mm) or less. The limit is inch (0.203mm). 16. Install a new intake manifold gasket to the cylinder head and install the manifold. Tighten the manifold in a crisscross pattern, starting from the inside and working outwards to 17 ft. lbs. (23 Nm). 17. Apply a thin coat of clean engine oil to the fuel injector O-rings. Install the fuel rail, injector and pressure regulator assembly to the lower intake manifold. 18. Thoroughly clean the mating surfaces and install the intake manifold plenum with a new gasket. 19. Install the throttle body assembly. 20. Install the intake manifold stay and the engine hanger. Plug in the fuel injector connectors. 21. Attach the EGR pipe connection. 22. Engage the engine control electrical connectors. 23. Engage the alternator wiring harness connection. 24. Connect the fuel line(s) and the throttle control cable brackets. 25. Connect the vacuum hose at the power brake booster and the PCV valve. Connect all remaining vacuum hoses and pipes. 26. Connect the accelerator cable, breather hose and air intake hose. 27. Connect the negative battery cable. 28. Start the engine and check for proper operation. 2.5L Engine 1. Disconnect the negative battery cable. On Sebring convertible, Cirrus, Stratus and Breeze models, disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding. 2. Properly relieve the fuel system pressure using the procedure outlined in Section 5. Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure MUST be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury. 3. Disconnect the fuel line(s) from the fuel rail assembly. On quick-connect fittings, squeeze the fitting retainer tabs together and separate the connection. Wrap shop towels around the connection to catch any gasoline spillage. 4. Loosen the throttle body air inlet hose clamp, then release the snaps holding the air cleaner housing cover to the housing. Remove the air cleaner cover and inlet hose from the engine. 5. Unplug the vacuum connection at the power brake booster and the PCV valve. Disconnect all remaining vacuum hoses and pipes, as necessary. Tag for identification, if necessary, to save time at assembly. NOTE: It may be helpful to identify and tag each sensor connector and vacuum connection as it is being removed or disengaged. This may save time at assembly. 6. Disengage the connectors from the Manifold Absolute Pressure (MAP) sensor and the intake air temperature sensors. 7. If necessary, disengage the power steering pressure switch and oxygen sensor connectors. Fig. 5: Remove the right side intake manifold plenum support bracket bolt 8. Remove the plenum support bracket located to the rear of the MAP sensor. 9. On all models except Sebring and Avenger coupes, loosen the attaching bolt, then remove the air inlet resonator. This is located on top of the engine intake manifold plenum. 10. On Sebring and Avenger coupes, remove the control wiring harness mounting fasteners located on top of the upper plenum near the valve cover. 11. Disconnect the Throttle Position Sensor (TPS) and the Idle Air Control (IAC) motor electrical connections. 12. Remove the throttle body assembly as outlined in Section Remove the throttle cable bracket. 14. Remove the EGR tube from the engine intake manifold.

4 15. On Sebring and Avenger coupes, remove the EGR valve and transducer assembly. Fig. 6: Remove the left side intake manifold plenum support bracket bolt Fig. 7: Remove the intake manifold plenum mounting bolts Fig. 8: Remove the intake manifold plenum from the engine Fig. 9: Remove the intake plenum-to-lower intake manifold gasket 16. Remove the plenum support bracket located to the rear of the EGR tube. 17. Remove the 7 bolts attaching the upper intake plenum to the lower manifold, and remove the plenum. Remove the intake plenum-to-lower manifold gasket. 18. Detach the fuel injector electrical connectors. 19. Remove the 4 bolts attaching the fuel rail to the intake manifold.

5 NOTE: There are spacers under each fuel rail bolt. 20. Remove the fuel rail, using care not to lose the spacers. Fig. 10: Loosen the power steering fluid reservoir mounting bracket bolts... Fig. 11:... then remove the reservoir bracket from the engine Fig. 12: There is a "hidden" intake manifold mounting bolt on the timing belt side that must be removed NOTE: It may be necessary to remove the power steering fluid reservoir and mounting bracket to access all of the lower intake manifold fasteners. 21. Remove the lower intake manifold attaching bolts. 22. Remove the intake manifold and discard the old gaskets. Fig. 13: Remove the intake manifold mounting fasteners

6 Fig. 14: Be careful not to lose the mounting fasteners and washers Fig. 15: Disconnect the vacuum hose from the intake manifold Fig. 16: Lift the intake manifold up and off of the engine Fig. 17: Remove the intake manifold gaskets from the engine To install: 23. Clean all gasket sealing surfaces. Check both surfaces for cracks or other damage. Check the intake manifold air passages for clogging. Clean if necessary. 24. Check the upper and lower manifold gasket surfaces for flatness using a straightedge and feeler gauge. 25. Surface must be flat within inch (0.152mm) per 12 inches (30.48cm) of manifold length. The limit is inch (0.203mm).

7 26. Properly position the new gaskets to the heads and install the lower intake manifold. Tighten the manifold in correct sequence, as illustrated following this procedure. A. Tighten the nuts in the front bank to 5 ft. lbs. (7 Nm). B. Tighten the nuts in the rear bank to 14 to 17 ft. lbs. (20 to 23 Nm). C. Tighten the nuts in the front bank to 14 to 17 ft. lbs. (20 to 23 Nm). D. Repeat Steps b and c again. 27. Apply a light coating of engine oil to the fuel injector O-rings. 28. Reinstall the fuel injectors into the engine. 29. Seat the injectors in place and tighten the fuel rail bolts to 8 ft. lbs. (12 Nm). 30. Engage the electrical connectors to the fuel injectors. 31. Reconnect the fuel line(s) to the fuel rail assembly. Exert a slight tug on the fuel line away from the fuel rail to verify positive engagement. 32. Install the upper intake plenum with new gaskets. 33. Tighten the plenum bolts to 13 ft. lbs. (18 Nm). 34. Reinstall the plenum support brackets and tighten to 13 ft. lbs. (18 Nm). 35. On Sebring and Avenger coupes, install the EGR valve and transducer assembly. 36. Install the EGR tube and tighten the screws to 95 inch lbs. (11 Nm). 37. Install the throttle cable bracket. 38. Install the throttle body assembly as outlined in Section Reconnect the TPS and IAC electrical connections. 40. On all models except Sebring and Avenger coupes, install the air inlet resonator and tighten the attaching bolt. 41. On Sebring and Avenger coupes, place the control wiring harness into correct position on the engine and tighten the mounting fasteners. 42. Engage the power steering pressure switch and oxygen sensor connectors, if previously disconnected. 43. Engage the MAP sensor and the intake air temperature sensor connectors. 44. Connect the vacuum hose at the power brake booster and the PCV valve. Connect all remaining vacuum hoses and pipes. 45. Connect the remaining engine control system electrical connectors. 46. Reinstall the air cleaner cover and air inlet hose. Tighten the intake hose-to-throttle body hose clamp. 47. Reconnect the negative battery cable. 48. Start the engine and check for leaks.

REMOVAL. Fig Sized for Print

REMOVAL. Fig Sized for Print ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting

More information

1995 Chrysler Cirrus 2.5L MFI 6cyl Repair Guides Charging System Alternator Auto...

1995 Chrysler Cirrus 2.5L MFI 6cyl Repair Guides Charging System Alternator Auto... Page 1 of 9 SAVE 20% + GET A $10 GIFT CARD ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: 20TUNE10 See Details Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998 TESTING REMOVAL & INSTALLATION

More information

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How

FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How 1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines

More information

EXHAUST SYSTEM AND INTAKE MANIFOLD

EXHAUST SYSTEM AND INTAKE MANIFOLD EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page GENERAL INFORMATION... 1 SERVICE PROCEDURES... 4 page TORQUE SPECIFICATION... 13 EXHAUST SYSTEMS The exhaust systems

More information

M-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS

M-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)

ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper) ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

EXHAUST SYSTEM AND INTAKE MANIFOLD

EXHAUST SYSTEM AND INTAKE MANIFOLD J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

Page 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove

More information

1988 Ford F-350 PICKUP

1988 Ford F-350 PICKUP 1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are

More information

Intake Manifold Replacement

Intake Manifold Replacement Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

Intake Manifold Replacement

Intake Manifold Replacement Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may

More information

INTAKE AIR TEMPERATURE SENSOR (IAT)

INTAKE AIR TEMPERATURE SENSOR (IAT) INTAKE AIR TEMPERATURE SENSOR (IAT) 4.8 Refer to the ELECTRICAL DIAGNOSTIC MANUAL for information on the function and testing of the intake air temperature sensor (IAT sensor). sm054 To prevent accidental

More information

M-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS

M-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS !!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

INTAKE MANIFOLD INSPECTION/REPLACEMENT

INTAKE MANIFOLD INSPECTION/REPLACEMENT ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.

More information

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top

More information

ELECTRONIC FUEL INJECTION (EFI)

ELECTRONIC FUEL INJECTION (EFI) Стр. 1 из 31 ELECTRONIC FUEL INJECTION (EFI) General Description The Electronic Fuel Injection (EFI) system was used on 1991 2.5L, 1986-92 3.0L (except SHO) and 1988-92 3.8L engines. The EFI fuel system

More information

INTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...

INTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER... I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE

More information

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic 2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.

More information

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST

1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST 1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

DESCRIPTION Chevrolet Chevy Van 5.7L Eng G20. Service Manual: FUEL INJECTION SYSTEM - TBI

DESCRIPTION Chevrolet Chevy Van 5.7L Eng G20. Service Manual: FUEL INJECTION SYSTEM - TBI Service Manual: FUEL INJECTION SYSTEM - TBI DESCRIPTION 1989 Chevrolet Chevy Van 5.7L Eng G20 The throttle body fuel injection system consists of 7 major sub-assemblies: fuel supply system, throttle body

More information

LSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body)

LSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) LSX Intake Manifold #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) Thank you for your purchase of the most innovative and powerful Gen III (LS1 and LS6) manifold ever developed. We are

More information

2001 Lincoln LS Workshop Manual

2001 Lincoln LS Workshop Manual Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional

More information

IN-VEHICLE REPAIR. Upper Intake Manifold

IN-VEHICLE REPAIR. Upper Intake Manifold 303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric

More information

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179 For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.

More information

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *

More information

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT

ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.

More information

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours

Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

Page 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301).

More information

BBK Intake Manifold Kit ( L) - Installation Instructions

BBK Intake Manifold Kit ( L) - Installation Instructions BBK Intake Manifold Kit (86-93 5.0L) - Installation Instructions The below installation instructions work for the following products: BBK Intake Manifold Kit (86-93 5.0L) Please read through the instructions

More information

L Intake Manifold Part #

L Intake Manifold Part # 86-93 5.0L Intake Manifold Part #5001-5002 I N S T A L L A T I O N I N S T R U C T I O N S Supplied Materials Bottom cover, Upper manifold, Lower manifold, Plenum cover plate, 1501 Throttle body (comes

More information

1998 F-150/250 Workshop Manual

1998 F-150/250 Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco

More information

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179

Edelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines Part #7179 For Chrysler 5.7L (Eagle), 6.1L and 6.4L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your

More information

2003 ACCORD - Intake Manifold Removal and Installation

2003 ACCORD - Intake Manifold Removal and Installation 2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose

More information

Intake Manifold Removal and Installation

Intake Manifold Removal and Installation 2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum

More information

INTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS...

INTAKE AND EXHAUST GROUP CONTENTS CHARGE AIR COOLER <2.0L ENGINE> GENERAL DESCRIPTION SERVICE SPECIFICATIONS... 15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL DESCRIPTION 15-2 SERVICE SPECIFICATIONS 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3

More information

Intake Manifold Removal

Intake Manifold Removal PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.

More information

Cylinder Head Setting Bolt Tightening Adaptor Injection Measuring Tool Set EFI Fuel Pressure Gauge

Cylinder Head Setting Bolt Tightening Adaptor Injection Measuring Tool Set EFI Fuel Pressure Gauge SFI SYSTEM (2JZGE) EG187 SFI SYSTEM (2JZGE) PREPARATION SST (SPECIAL SERVICE TOOLS) 0920576030 Cylinder Head Setting Bolt Tightening Adaptor ECT sensor 0926841045 Injection Measuring Tool Set (0926841070)

More information

Installation Instructions Part Number

Installation Instructions Part Number Installation Instructions Part Number 84152143 Thank you for choosing Chevrolet Performance as your high performance source. Chevrolet is committed to providing proven, innovative performance technology

More information

EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)

EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE) ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

EXHAUST GAS RECIRCULATION (EGR) SYSTEM

EXHAUST GAS RECIRCULATION (EGR) SYSTEM ENGINE EG169 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (California only) EG170 ENGINE To reduce NOx emissions, part of the exhaust gases are recirculated through the EGR valve to the intake manifold to lower

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

Cylinder head, removing and

Cylinder head, removing and Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder

More information

INTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose

INTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose INTAKE MANIFOLD COLLECTOR Removal and Installation PFP:14003 ABS0095V 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose 4. EVAP canister purge volume control solenoid valve 5. Bracket 6. Intake

More information

Power Steering Pump. GM Century/Lumina/Grand Prix/Intrigue REMOVAL & INSTALLATION BLEEDING

Power Steering Pump. GM Century/Lumina/Grand Prix/Intrigue REMOVAL & INSTALLATION BLEEDING 1 of 9 GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Power Steering Pump REMOVAL & INSTALLATION BLEEDING When servicing the power steering pump, inspect the power steering fluid. Look for foaming, milky

More information

2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body.

2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body. 2002 Silverado K 4WD Applies to: 4.8L, 5.3L, and 6.0L Report a problem with this article Removal Procedure 1. Remove the air intake duct. Refer to Air Cleaner Resonator Outlet Duct Replacement. 2. Disconnect

More information

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS 5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE

More information

ENGINE AND EMISSION CONTROL

ENGINE AND EMISSION CONTROL 17-1 ENGINE AND EMISSION CONTROL CONTENTS EMISSION CONTROL SYSTEM... 2 GENERAL... 2 Outline of Changes... 2 GENERAL INFORMATION... 2 SERVICE SPECIFICATION... 2 VACUUM HOSE... 3 Vacuum Hose Piping Diagram...

More information

FUEL INJECTION SYSTEM - MULTI-POINT

FUEL INJECTION SYSTEM - MULTI-POINT FUEL INJECTION SYSTEM - MULTI-POINT 1988 Jeep Cherokee 1988 Electronic Fuel Injection JEEP MULTI-POINT 4.0L Cherokee, Comanche, Wagoneer DESCRIPTION The Multi-Point Electronic Fuel Injection (EFI) system

More information

Installation Instructions

Installation Instructions Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

ENGINE AND EMISSION CONTROL

ENGINE AND EMISSION CONTROL 17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL........... 17-3 GENERAL INFORMATION....... 17-3 SERVICE SPECIFICATIONS..... 17-3 ON-VEHICLE SERVICE.......... 17-3 ACCELERATOR CABLE CHECK

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

FUEL PRESSURE REGULATOR

FUEL PRESSURE REGULATOR EG2214 3VZE ENGINE FUEL PRESSURE REGULATOR ONVEHICLE INSPECTION CHECK FUEL PRESSURE (See step 2 on page EG2206) COMPONENTS FOR REMOVAL AND INSTALLATION FUEL PRESSURE REGULATOR REMOVAL 1. DISCONNECT NEGATIVE

More information

ENGINE 6G74 3.5L-SOHC-24 VALVE

ENGINE 6G74 3.5L-SOHC-24 VALVE 11A ENGINE General Information/Service Specifications ENGINE 6G74 3.5L-SOHC-24 VALVE GENERAL INFORMATION Items Specifications Type V-type, Over Head Camshaft Number of cylinders 6 Bore mm 93.0 Stroke mm

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

ENGINE AND EMISSION CONTROL

ENGINE AND EMISSION CONTROL 17-1 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL SYSTEM........ 3 SERVICE SPECIFICATION............... 3 ON-VEHICLE SERVICE.................. 3 Accelerator Cable Check and Adjustment... 3 ACCELERATOR

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

ASSEMBLY/INSTALLATION INSTRUCTIONS

ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath

More information

ENGINE MECHANICAL <3.0L ENGINE>

ENGINE MECHANICAL <3.0L ENGINE> 11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-3 SPECIAL TOOLS................ 11C-4 ON-VEHICLE SERVICE........... 11C-6 DRIVE

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

INTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER

INTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER 15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL INFORMATION 15-2 SERVICE SPECIFICATION 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3 SPECIAL

More information

Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.

More information

SLP Camaro ZL1 STAGE 3 (650 HP)

SLP Camaro ZL1 STAGE 3 (650 HP) SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

Pre-Installed. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal

Pre-Installed. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS1/6*, 1997-2004 Corvette, 1998-2002 Camaro/Firebird,

More information

Page 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

2011 Mercury Grand Marquis LS

2011 Mercury Grand Marquis LS Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.

More information

SECTION 4 - FUEL SYSTEMS AND CARBURETION

SECTION 4 - FUEL SYSTEMS AND CARBURETION SECTION - FUEL SYSTEMS AND CARBURETION FUEL SYSTEMS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -62 FUEL PUMP - - - - - - -

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

ENGINE MECHANICAL <3.0L>

ENGINE MECHANICAL <3.0L> 11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-2 SPECIAL TOOLS................ 11C-3 ON VEHICLE SERVICE........... 11C-5 DRIVE BELT

More information

1999 Oldsmobile Truck Bravada V6-4.3L VIN W

1999 Oldsmobile Truck Bravada V6-4.3L VIN W 1 of 6 8/24/2015 9:53 PM 1999 Oldsmobile Truck Bravada V6-4.3L VIN W Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Meter Body» Service and Repair CLEANING AND INSPECTION PROCEDURE

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

THROTTLE BODY. ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. EG1 182

THROTTLE BODY. ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. EG1 182 EG1182 THROTTLE BODY ON VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Check that the throttle linkage moves smoothly. (b) Check the vacuum at each port. Start the engine. Check the vacuum with your finger.

More information

97 00 dodge trucks CKP CPS

97 00 dodge trucks CKP CPS 97 00 dodge trucks CKP CPS Crankshaft Position (CKP) Sensor OPERATION The crankshaft position sensor generates pulses and sends them to the PCM. The PCM interprets this input signal to determine the crankshaft

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

GROUP 11C 11C-1 CONTENTS GENERAL DESCRIPTION... 11C-2 ENGINE DIAGNOSIS... 11C-2 CRANKSHAFT FRONT OIL SEAL... 11C-30 SPECIAL TOOLS...

GROUP 11C 11C-1 CONTENTS GENERAL DESCRIPTION... 11C-2 ENGINE DIAGNOSIS... 11C-2 CRANKSHAFT FRONT OIL SEAL... 11C-30 SPECIAL TOOLS... 11C-1 GROUP 11C CONTENTS GENERAL DESCRIPTION 11C-2 ENGINE DIAGNOSIS 11C-2 SPECIAL TOOLS 11C-3 ON VEHICLE SERVICE 11C-5 DRIVE BELT TENSION CHECK AND ADJUSTMENT 11C-5 IGNITION TIMING CHECK 11C-5 IDLE MIXTURE

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

DOWNLOAD ENHANCED INSTALL MANUALS

DOWNLOAD ENHANCED INSTALL MANUALS U 3 October 2016 1041564 6.7L Performance Intake Plate Manual (I-00371) 1 DOWNLOAD ENHANCED INSTALL MANUALS Cummins 6.7L High Flow Intake Plenum Cover 1041564 2008-2016 6.7L RAM 2500-3500 Pickup PLEASE

More information

1994 ENGINE PERFORMANCE TOYOTA SYSTEM & COMPONENT TESTING

1994 ENGINE PERFORMANCE TOYOTA SYSTEM & COMPONENT TESTING 1 of 65 12/5/2014 1:13 PM 1994 ENGINE PERFORMANCE TOYOTA SYSTEM & COMPONENT TESTING INTRODUCTION Before testing separate components or systems, perform procedures in articles listed below: BASIC TESTING

More information

ENGINE DEVELOPMENT INC.

ENGINE DEVELOPMENT INC. 2003 Ford Expedition 4.6L& 5.4L We encourage you to read this manual thoroughly before you begin work, and perform the following: 1. A quick parts check to make certain your kit is complete. If you discover

More information

2013 Kia Optima L4-2.0L Turbo

2013 Kia Optima L4-2.0L Turbo 1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted

More information

For Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID

For Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX

2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX 2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE SECTION 1 FU(H4SO) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) INTAKE (INDUCTION) EC(H4SO) IN(H4SO) This service manual has been prepared to

More information

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM

More information