Reproduction. Not for. Parts Manual. IS3200Z Series Zero-Turn Riding Mower

Transcription

1 Parts Manual IS3200Z Series Zero-Turn Riding Mower Models: Description: IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZKAV3761) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBV3661) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZKAV3772) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZBV3672) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBV3261) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZBV3272) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZKAV3561) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZKAV3572) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBVE3761 ANSI EXP) IS3200Z Series w/ ROPS (IS3200ZBVE37 ANSI EXP) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZBVE2872 CAL) IS3200Z Series w/ ROPS (IS3200ZBV36 ANSI EXP) " Side Discharge icd Mower Deck (3200Z/72 ANSI EXP) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBV3661 ANSI EXP) IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBVE3761) IS3200Z Series w/ 72" Mower Deck & ROPS (IS3200ZBVE3772) See Inside Front Cover for Additional Models Briggs and Stratton Power Products Group, LLC North Main Street Munnsville, NY USA Revision J Rev. Date: 9/1/16

2 Models: Description: IS3200Z Series w/ 61" Mower Deck & ROPS (IS3200ZBVE2861 CAL)

3 Table Of Contents MODEL COMPONENTS PAGE Main Frame & Front Suspension Group... 4 Rear Bumper & ROPS... 6 Seat Plate & Floor Group... 8 Seat Replacement Parts & Fuel Supply Hose, Tank Replacement Parts, and EVAP Group Fuel Tank & Mount Group Fuel Supply Hose, Tank Replacement Parts & Evap Canister Group - CAL Models Instrument Control Panel - All Other Models Instrument Control Panel - Kawasaki DFI Models Only Engine & PTO Group Engine Service Parts - Briggs & Stratton Vanguard Big Block Engine Service Parts - Kawasaki (FX651V - FX1000V) Transaxle Drive Group Motion Control - Control System Motion Control - Handles & Dampeners Hydraulic Group Parking Brake Group Rear Suspension Group Deck Lift Group Transaxle SERVICE PARTS - ZT Wheel & Tire Group Decal Group - Brand & Model S/N: & Below Decal Group - Brand & Model S/N: & Above Decal Group - Safety & Operation (USA Models) Decal Group - Safety & Operation (Export Models) " Mower Deck Group - Rollers & Casters " & 72" Mower Deck Group - Deck Hangers " Mower Deck Group - Housing, Covers, Spindles & Blades " Mower Deck Group - Pulleys, Belt & Idler Arm " Mower Deck Group - Housing, Covers, Spindles & Blades " Mower Deck Group - Pulleys, Belt, & Idler Arm " & 72" Mower Deck Group - Pusher Bars " Mower Deck Group - Rollers & Casters Spindle Service Parts Electrical Group - Briggs & Stratton & Kawasaki Carbureated Models Electrical Group - Kawasaki DFI Models Electrical Group - Briggs & Stratton EFI Models Electrical Schematics - Kawasaki FX S/N: & Below Electrical Schematics - B&S / S/N: & Below Electrical Schematics - Kawasaki DFI S/N: & Below Electrical Schematics - B&S 61E877 EFI Electrical Schematics - Kawasaki DFI S/N: & Above Electrical Schematics - Kawasaki FX S/N: & Above Electrical Schematics - B&S / S/N: & Above Electrical Schematics - B&S 49E877 EFI S/N: & Above Torque Specification Chart... Inside Back Cover

4 Main Frame & Front Suspension Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

5 Main Frame & Front Suspension Group REF NO PART NO. QTY. DESCRIPTION WASHER, BELLEVILLE X NUT, 3/4-16, HEX JAM NYLON LOCK CAP, LOW PROFILE, STEEL BOLT, 1/4-28 X 1/2, GD5 CZ WASHER, 3/8 SAE X16 2 BOLT, 3/8-16 X 2 GD5 CZ X18 2 BOLT, 3/8-16 X 2-1/4 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE GREASE FITTING, 1/4-28 STRAIGHT BUSHING, 1.00 X 1.13 X 1.38, PLASTIC NUT, 3/4-16 HEX NYLON LOCK NUT, 1/4-20 HEX SERR. FLANGE X28 4 BOLT, 3/4-16 X 3-1/2 GD8 CZ SPACER,.76 X 1.00 X NUT, 3/4-16 HEX JAM WASHER, 3/4 SAE SEAL, GREASE BEARING, TAPERED ROLLER, SHOCK / SPRING ASSEMBLY, OE B 2 WELD, CASTER YOKE - RED BALL JOINT, 3/4-16, MALE BEARING, CUP (SV) BUMPER, RUBBER 1/ SPACER,.75 X 1.50 X 1.00, CZ 25-1 * WELD, MAIN FRAME, IS3200Z - RED * If frame is damaged, call ext B 1 WELD, A-ARM, IS3200Z, LH - RED (61" Models Only) B 1 WELD, A-ARM, IS3200Z, RH - RED B 1 WELD, A-ARM, LH, IS3200Z-72 - RED (72" Models Only) CLAMP, 5/16, DOUBLE, WIRE & TUBE (To hold spanner wrench) X6 1 BOLT, 1/4-20 X 3/4 GD5 YZ WASHER, 1/4 SAE NUT, 1/4-20 HEX NYLOCK FLANGE Footnotes

6 Rear Bumper & ROPS NOTE: Unless noted otherwise, use the standard hardware torque specification chart

7 Rear Bumper & ROPS REF NO PART NO. QTY. DESCRIPTION PLUG, PANEL, BLACK WASHER, 5/16 SAE WASHER, 1/2 SAE WASHER, 3/8 GD.9 FLAT NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE SPACER,.52 X 1.00 X.38, CZ SEAT BELT, RETRACTING - ASSM SCREW, 1/2-13 X 1.00, SHCS ROPS, IS3200 (Call ex.707 for ROPS service) X8 6 BOLT, 5/16-18 X 1 GD5 CZ X8 2 BOLT, 3/8-16 X 1 GD5 CZ X10 7 BOLT, 1/2-13 X 1-1/4 GD5 CZ X12 1 BOLT, 1/2-13 X 1-1/2 GD5 CZ A 2 BAR, MOUNT, SEAT BELT, IS700Z - BLK B 1 PLATE, CARB PROTECTOR - RED A 1 PLATE, HEAT SHIELD, IS BLK B 1 WELD, BUMPER, IS3200Z - RED X24 4 BOLT, 1/2-13 X 3" GD NUT, 1/2-13 HEX SIDE LOCK Footnotes

8 Seat Plate & Floor Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

9 Seat Plate & Floor Group REF NO PART NO. QTY. DESCRIPTION SAFETY WALK, FLOOR REST, 6.00 X SAFETY WALK, FLOOR PLATE, S50X, 10X NUT, 3/8-16 HEX NYLOCK FLANGE KNOB-INT THR ARM 2.12WD 1.06LG WASHER, 5/16 SAE X8 5 BOLT, 5/16-18 X 1 GD5 CZ WASHER, 3/8 USS NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL X10 1 BOLT, 5/16-18 X 1-1/4, CARRIAGE CZ X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE SEAT, IS3100 / IS5100 (S/N: & Below) X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS NUT, #10-24 HEX NYLON LOCK WASHER,.39 X 2.00 X X WASHER, 3/8 SAE X18 2 BOLT, 3/8-16 X 2-1/4 GD5 CZ X48 1 BOLT, 3/8-16 X 6 GD5 CZ SPACER,.38 X.50 X 5.06, CZ SPRING,.688 ID X.130 WIRE DIA SWITCH (SEE ELECTRICAL GROUP) NUT, 5/16-18 HEX NYLOCK FLANGE ASSM, SEAT PLATE W/ DECALS, IS3200Z, DOM ( B)(Export Models Only) ASSM, SEAT PLATE W/ DECALS, IS3200Z, ANSI-EXP ( B)(Export Models Only) A 1 WELD, SEAT SWITCH, IS700 - BLK B 1 PLATE, FLOOR, REMOVABLE, IS3100Z - RED B 1 PLATE, FRONT FLOOR, IS3100Z - RED MNT, VBRTN, RBBR A 1 GUARD, DEBRIS, IS2100Z - BLK X6 3 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE BODY CLIP, 5/ /4 MATERIAL SEAT, HIGH BACK, SEAT INC (S/N: & Above) Footnotes

10 Seat Replacement Parts & NOTE: Unless noted otherwise, use the standard hardware torque specification chart

11 Seat Replacement Parts & REF NO PART NO. QTY. DESCRIPTION X1 1 COVER, SEAT BACK, EVC, SEATS INC X2 1 COVER, CUSHION, EVC, SEATS INC X3 1 ARM REST ASSEMBLY X4 1 ARM REST PAD X1 1 ARM PAD ASSEMBLY X2 1 ARM REST ASSEMBLY (LEFT AND RIGHT) X3 1 BACK COVER X4 1 CUSHION COVER X5 1 TRACK KIT Footnotes

12 Fuel Supply Hose, Tank Replacement Parts, and EVAP Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

13 Fuel Supply Hose, Tank Replacement Parts, and EVAP Group REF NO PART NO. QTY. DESCRIPTION CLAMP, HOSE, EXTERNAL, 1/2 - RED X14P5 1 HOSE, 1/4" FUEL, 14.50" X28P5 1 HOSE, 1/4" FUEL, 28.50" X10P5 1 HOSE, 1/4" FUEL, 10.50" (B&S Engines Only) X12P5 1 HOSE, 1/4" FUEL, 12.50" (Kawasaki Engines Only) VALVE, FUEL SHUT-OFF, FITTING, 3/16" TEE, BARB TYPE, HDPE X18 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki DFI & B&S Engines Only) X28P5 1 HOSE, VAPOR, 5MM ID, LG X12 1 HOSE, VAPOR, 5MM ID, LG (B&S Engines Only) X3 2 HOSE, VAPOR, 5MM ID, 3.00 LG X20 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki DFI Engines Only) A 1 BRACKET, FUEL VALVE, IS BLK X6 2 BOLT, 5/16-18 X 3/4 GD WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE TIE, SELF-LOCKING, 12" REMOTE, VENT ASSEMBLY, NO VALVE (SV) GROMMET (SV) X3 2 FUEL FILTER (SV) FILTER, FUEL BUSHING-FUEL TANK RED RUBBER (SV) HOSE ASSEMBLY (SV) X33 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Carbureated Models Only) X14 1 HOSE, VAPOR, 5MM ID, LG (Kawasaki Carbureated Models Only) Footnotes

14 Fuel Tank & Mount Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

15 Fuel Tank & Mount Group REF NO PART NO. QTY. DESCRIPTION TANK, FUEL, IS2000 & IS LH TANK, FUEL, IS2000 & IS RH FUEL CAP, 3-1/2", MANAGED VENT OUT, 12" B 2 BADGE, IS IS RED SCREW, #10-24 X 3/8 ALLEN BHBZ X6 8 BOLT, 5/16-18 X 3/4 GD WASHER, 5/16 LOCK YZ WASHER, 5/16 F436 FLAT GAUGE, FUEL, 12 (SV) X1 2 GROMMET, FUEL GAUGE (SV) Footnotes

16 Fuel Supply Hose, Tank Replacement Parts & Evap Canister Group - CAL Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

17 Fuel Supply Hose, Tank Replacement Parts & Evap Canister Group - CAL Models REF NO PART NO. QTY. DESCRIPTION CLAMP, HOSE, EXTERNAL, 1/2 - RED X13 1 HOSE, 1/4" FUEL, 13.00" X26P5 1 HOSE, 1/4" FUEL, 26.50" VALVE, FUEL SHUT-OFF, X23 1 HOSE, 1/4" FUEL, 23.00" CNSTR, CARB, 6 GAL CLAMP, 3" ID, CUSHIONED, STAINLESS X6 4 SCREW,1/4-20X3/4, ZINC PHOS & OIL NUT, 1/4-20 HEX NYLOCK FLANGE FITTING, 3/16" TEE, BARB TYPE, HDPE X22 2 HOSE, VAPOR, 5MM ID, LG X5 1 HOSE, VAPOR, 5MM ID, 5.00 LG X19 1 HOSE, VAPOR, 5MM ID, LG X24P5 1 HOSE, VAPOR, 5MM ID, LG A 1 PLATE, MOUNT, CANISTER, IS2100Z - BLK X6 2 BOLT, 5/16-18 X 3/4 GD5 CZ WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE TIE, SELF-LOCKING, 12" GROMMET (SV) BUSHING-FUEL TANK RED RUBBER (SV) HOSE ASSEMBLY (SV) X3 2 FUEL FILTER (SV) DUST FILTER, CANISTER (SV) REMOTE, VENT ASSEMBLY, NO VALVE (SV) Footnotes

18 Instrument Control Panel - All Other Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart

19 Instrument Control Panel - All Other Models REF NO PART NO. QTY. DESCRIPTION X4 3 SCREW,ALLEN HEAD 1/4-20X.500 ZINC PHOS PLUG,.820X1.44 HOLE, BLACK PLASTIC SWITCH, BLADE ENGAGEMENT SWITCH, IGNITION, 6 POST * HOUR METER, ASSEMBLY ( ) CABLE, CHOKE CONTROL, 51 (Z) (Briggs & Stratton Carbureted Models Only) X6 2 SCREW, #10-24 X 3/4 ROUND PHILLIPS A 1 PANEL, CONTROL, IS2100Z - BLK (Briggs & Stratton Carbureted Models Only) RING, SWITCH RETAINER X1 1 KNOB, THROTTLE CONTROL (SV) CABLE, THROTTLE, 47" LEVER, THROTTLE CONTROL, HEAVY-DUTY O-RING, 7/8 ID X 1/16 W NUT, #10-24 HEX NYLON LOCK TIE, SELF-LOCKING, 12" NUT, 3/8-24 HEX KEY, IGNITION MOLDED SET (SV) COVER, PLASTIC, SNAP ON (SV) NUT, PLASTIC (SV) A 1 PANEL, CONTROL, IS2100/ BLK (Briggs & Stratton EFI Models Only) LIGHT, INDICATOR, EFI (Briggs & Stratton EFI Models Only) CABLE, THROTTLE, 52" (Kawasaki Carbureted Models Only) Footnotes * When replacing this hour meter, please call our service department at ext

20 Instrument Control Panel - Kawasaki DFI Models Only NOTE: Unless noted otherwise, use the standard hardware torque specification chart

21 Instrument Control Panel - Kawasaki DFI Models Only REF NO PART NO. QTY. DESCRIPTION A 1 PANEL, CONTROL, IS3100Z - BLK X4 3 SCREW, 1/4-20 X 1/2 ALLEN BH ACTUATOR, ROCKER SWITCH - RED SWITCH, IGNITION, 6 POST KEY, IGNITION, MOLDED SET COVER PLASTIC NUT RING, SWITCH RETAINER SWITCH, BLADE ENGAGEMENT * HOUR METER, ASSEMBLY ( ) PLUG,.820X1.44 HOLE, BLACK PLASTIC LAMP, MALFUNCTION INDICATOR BODY, ROCKER SWITCH O-RING, 7/8 ID X 1/16 W Footnotes * When replacing this hour meter, please call our Service Department at ext

22 Engine & PTO Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

23 Engine & PTO Group REF NO PART NO. QTY. DESCRIPTION 1 FX1000V-AS14-R 1 ENGINE, KAWA, DFI (Kawasaki DFI Models Only) SPACER, 1.13 X 1.75 X 1.35, CZ MUFFLER, 37 HP KAWASAKI (Kawasaki Models Only) CLUTCH, WARNER, 250 ft lbs " BOLT, CRANKSHAFT, 7/16-20 X 3-1/4, GD GROMMET, 7/8"ID, 1/4" THICK STK EXTENSION, TAILPIPE, 3" (Kawasaki Models Only) HOSE, OIL DRAIN PULLEY, 4.75 OD X 1-1/8 BORE, BC X10 1 KEY, 1/4 SQ X 1-1/ A 1 ANCHOR, CLUTCH, IS600-IS700 - BLK CLUTCH ANCHOR PAD WASHER,.34 X 1.25 X 10 GA WASHER, 5/16 SAE (Qty: 3 Kawasaki Models Only) X8 4 BOLT, 5/16-18 X 1 GD5 YZ NUT, 5/16-18 HEX NYLOCK FLANGE X18 1 BOLT, 5/16-18 X 2-1/4 GD5 TFL, ZN NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) BELLEVILLE WASHER X.442 X CLAMP, VINYL INSULATED WASHER, 1/4 SAE X6 1 BOLT, 1/4-20 X 3/4 GD5 YZ NUT, 1/4-20 HEX SERR. FLANGE ADAPTER-OIL DRAIN (Kawasaki Models Only) X14 4 BOLT, 5/16-24 X 1-3/4, GD8 (B&S Models Only) BOLT, 3/8-16 X 1-1/4, SF, PLT W/PATCH (Kawasaki Models Only) SCREW,SELF-TAP,#8-32 X 3/8,WASH HEX, CZ (Kawasaki & B&S 49E877 Models Only) G1 1 ENGINE, B&S, VANGUARD (B&S Carbureted Models) TAIL PIPE EXTENTION, 1.78"ID X 5" LG (B&S Models Only) X1 1 CLAMP, TAILPIPE, 1-7/8" (B&S Models Only) WASHER, 5/16 INT. TOOTH LOCK (Qty: 1 Kawasaki Models Only) X1 1 MUFFLER, ASSY, SERVICE PART (B&S Carbureted Models Only) SET SCREW, 5/16-18 X 3/8, KNURL (SV) METRIC ADAPTER, M14-1.5" TO 3/8 NPTF (B&S Models Only) NUT, HEX, M8-1.25, CZ, GD 8.8 (Kawasaki Models Only) WASHER, 5/16 LOCK CZ (Kawasaki Models Only) BOLT, M X 20MM GD8.8 (Kawasaki Models Only) 38 61E J1 1 ENGINE, 37HP, BRIGGS, VANGUARD, EFI (B&S 61E877 EFI Models Only) NUT, 5/16-24, NYLOCK FLANGE, GD8, CZ (B&S Models Only) J1 1 ENGINE, 32, B&S, J1 (B&S Carbureated Models) 41 FX1000V 1 ENGINE, 35, KAWASAKI (Kawasaki Carbureated Models Only) Footnotes

24 Engine & PTO Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

25 Engine & PTO Group REF NO PART NO. QTY. DESCRIPTION 42 49E G1 1 ENGINE, 28, BRIGGS VANGUARD, EFI (B&S 49E877 EFI Models Only) EXTENSION, TAILPIPE, 3", BLACK (B&S 49E877 EFI Models Only) Footnotes

26 Engine Service Parts - Briggs & Stratton Vanguard Big Block NOTE: Unless noted otherwise, use the standard hardware torque specification chart

27 Engine Service Parts - Briggs & Stratton Vanguard Big Block REF NO PART NO. QTY. DESCRIPTION " AIR CLEANER ASSEMBLY (809670) AIR FILTER - INNER (821136) AIR FILTER - OUTER (841497) CAP - AIR CLEANER (842621) RUBBER DUST CAP (842623) CAP - A/C RAIN (809907) BRACKET - AIR CLEANER (809878) HOSE (Carbureated Models Only) CLAMP - HOSE (807376) OIL FILTER Footnotes

28 Engine Service Parts - Kawasaki (FX651V - FX1000V) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

29 Engine Service Parts - Kawasaki (FX651V - FX1000V) REF NO PART NO. QTY. DESCRIPTION X1 1 AIR FILTER ASSEMBLY,22,24&26HP KAWASAKI ( ) X4 1 AIR FILTER,SECOND,FX651V THRU FX999 ENG ( ) X3 1 AIR FILTER,PRIMARY,FX 651,852, & 999 ENG ( ) X2 1 CASE, AIR FILTER, 22, 24 & 26HP KAWASAKI ( ) X8 1 DUST VALVE,AIR FILTR,22,24&26HP KAWASAKI ( ) CAP, RAIN ( ) X5 1 BRKT,AIR FILTER,22,24&26HP KAV, OUTER ( H) X6 1 BRKT,AIR FILTER,22,24&26HP KAV, INNER ( H) X9 1 BREATHER TUBE, AIR FILTR,22,24&26HP KAWA ( ) X10 1 AIR INLET TUBE,AIR FILTR,22,24&26HP KAWA ( ) CLAMP ( ) X1 1 FILTER,OIL,KAWA FS,FX651,700,FR 603 & 726CC ENG ( ) X1 1 FILTER,OIL,KAWA FX751,801,851,921,100 ( ) FOR KAWASAKI MODELS FX751 & LARGER Footnotes

30 Transaxle Drive Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

31 Transaxle Drive Group REF NO PART NO. QTY. DESCRIPTION PULLEY, FLAT IDLER, 6-3/4" BELT, B-SEC, 129"EL, ARAMID, WRAPED PULLEY-IDLER-V, 5.83OB,.38ID,.94W, STL SPACER,.52 X 1.00 X.56, CZ PULLEY, C-SEC, V-IDLER, 6.25"ODX3/8ID SPACER, IDLER ARM, 1/2, PM SPACER,.52 X.84 X 1.53, PM SPRING-EXT, 1.25OD X 9.3LG X.142WR, BLK SHIELD, PULLEY BEARING, CZ SHIELD, BEARING PULLEY, 3/8ID, CZ A 1 WELD, IDLER ARM, 7.50, BEARINGS - BLK BEARING, BALL, AXLE X40 1 BOLT-1/2-13 X 5 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE EYE BOLT, 3/8-16 X 4, 2.13THRD, 1" EYE, CZ NUT, 3/8-16 HEX SERRATED FLANGE SPACER,.39 X 1.00 X X22 1 BOLT, 3/8-16 X 2-3/4 GD5 YZ WASHER, 3/8 GD.9 FLAT SPACER,.39 X 1.00 X.50, CZ WASHER-3/8 FENDER X18 1 BOLT, 3/8-16 X 2-1/4 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE Footnotes

32 Motion Control - Control System NOTE: Unless noted otherwise, use the standard hardware torque specification chart

33 Motion Control - Control System REF NO PART NO. QTY. DESCRIPTION A 2 PLATE, CONTROL SYSTEM LOCK - BLK PAD,.77 X 3.50 X.25, POLYURETHANE ROD, HYDRO LINKAGE A 2 PLATE, CONTROL MOUNT - BLK BALL JOINT 5/16-24 RH FEMALE BRONZE RACE X10 14 BOLT, 5/16-18 X 1-1/4 GD5 YZ NUT, 3/8-16 HEX SIDE LOCK BALL JOINT 5/16-24 LH FEMALE BRONZE RACE NUT, 5/16-18 HEX NYLOCK FLANGE ROD, HYDRO LINKAGE, SPACER,.33 X.63 X 1.25, CZ X20 2 BOLT, 5/16-18 X 2-1/2 GD5 YZ X20 2 BOLT, 3/8-16 X 2-1/2 GD5 YZ X12 2 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ NUT, 3/8-16 HEX NYLOCK FLANGE SPACER,.39 X 1.00 X.50, CZ PIVOT, CONTROL SYSTEM WASHER-3/8 FENDER SPACER,.39 X.55 X.38, CZ BEARING,.375" ID X.875" OD X.341" THK WAVE WASHER, 1/2"ID X 087"OD X.01 THK PAD, CONTROL SYSTEM PLATE, CONTROL SYSTEM ARM - HT A 2 LINK, CONTROL SYSTEM ARM, IS BLK BOLT, 3/8-16 X 3/8, 1/2 SHOULDER SPACER,.39 X.75 X.69, CZ NUT, 5/16-24 HEX NUT, 5/16-24 HEX, LH X8 2 BOLT, 7/16-14 X 1 GD NUT, 7/16-14 HEX NYLON LOCK WASHER, 5/16 SAE WASHER, 1/2 SAE Footnotes

34 Motion Control - Handles & Dampeners NOTE: Unless noted otherwise, use the standard hardware torque specification chart

35 Motion Control - Handles & Dampeners REF NO PART NO. QTY. DESCRIPTION A 1 PLATE, NEUTRAL LOCK, RH - BLK A 1 PLATE, NEUTRAL LOCK, LH - BLK A 2 BRACKET, SWITCH MOUNT - BLK WASHER, 5/16 SAE GUARD, RUBBER MOTION CONTROL PUSH RIVET (TREE TYPE), BLACK SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC BOLT,1/4-20X.75,GR5,RH SH SQ NK,ZNC/CLR NUT, 1/4-20 HEX NYLOCK FLANGE X6 6 BOLT, 5/16-18 X 3/4 GD X24 4 BOLT, 5/16-18 X 3 GD5 CZ NUT, 3/8-16 HEX NYLON LOCK NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) WASHER, 3/8 SAE X10 4 BOLT, 5/16-18 X 1.25" GD 5 TFL X14 2 BOLT- 5/16-18 X 1-3/4 GD5 TFL NUT, 5/16-18 HEX NYLOCK FLANGE X14 4 BOLT, 3/8-16 X 1-3/4 GD X6 6 BOLT, 3/8-16 X 3/4 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE BUSHING, FLANGE 3/8ID X 7/8 LONG PIN, HAIR,.0915 X 1-7/ SPRING, REVERSE RETURN X8 2 BOLT, 7/16-14 X 1 GD NUT, 7/16-14 HEX NYLON LOCK COLLAR, 3/8 SET ROD, NEUTRAL RETURN, CZ FLANGED BUSHING, 3/8IDX.63ODX.8125FL MM BALL STUD, 5/16-18 X 3/4 THDS GRIP, FOAM, 3/4 ID, 16 LONG (S/N: & Below) A 2 MOUNT, CONTROL ARM - BLK (S/N: & Below)(9.0" Total Length, 4 Adjustment Holes) A 1 WELD, CONTROL HANDLE-LH - BLK (S/N: & Below) A 1 WELD, CONTROL HANDLE-RH - BLK (S/N: & Below) DAMPENER, CONTROL,#(P6709/P3610) BEARING, FLANGE BEARING, BRONZE FLANGE, 3/ A 1 WELD, CONTROL SHAFT, LH - BLK A 1 WELD, CONTROL SHAFT, RH - BLK A 2 MOUNT, CONTROL ARM - BLK (S/N: & Above)(10.95" Total Length, 3 Adjustment Holes) GRIP, FOAM, 1" ID, 16" LONG (S/N: & Above) Footnotes

36 Motion Control - Handles & Dampeners NOTE: Unless noted otherwise, use the standard hardware torque specification chart

37 Motion Control - Handles & Dampeners REF NO PART NO. QTY. DESCRIPTION A 1 WELD, HANDLE MOTION CNTRL, 16.5, 1.0, LH - BLK (S/N: & Above) A 1 WELD, HANDLE MOTION CNTRL, 16.5, 1.0, RH - BLK (S/N: & Above) Footnotes

38 Hydraulic Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

39 Hydraulic Group REF NO PART NO. QTY. DESCRIPTION ZT-5400, LONG AXLE, RH, R ZT-5400, LONG AXLE, LH, L A 1 PLATE, RESERVOIR MOUNT - BLK WASHER, 1/4 SAE HYDRO TANK, HYDRO-GEAR 71938, 1 LITER BOLT, 1/2-13 X 1-1/4, SF, PLT W/PATCH CLAMP, #10 HOSE, STAINLESS NUT, 1/4-20 HEX NYLOCK FLANGE X8 4 BOLT, 5/16-18 X 1 GD5 CZ WASHER, 5/16 SAE NUT, 5/16-18 HEX NYLOCK FLANGE X8 2 BOLT, 1/4-20 X 1 GD5 CZ FITTING, 90 DEG, 5/ PULLEY, ZT5400 (53179) FAN, ZT WASHER, ZT5400, SLOTTED NUT, ZT SPACER, ANTI ROTATE, ZT FITTING, 45, 5/8 TUBE TO 7/8-14 O-RING X23P5 1 HOSE, 5/8, PUSH-LOCK, X20P5 1 HOSE, 5/8, PUSH-LOCK, X3 2 HOSE, 5/8, PUSH-LOCK, 3.00 Footnotes

40 Parking Brake Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

41 Parking Brake Group REF NO PART NO. QTY. DESCRIPTION BEARING, BRONZE FLANGE, 3/ NUT, 5/16-24 HEX NYLON LOCK WASHER, 5/16 SAE NUT, 3/8-16 HEX NYLOCK FLANGE SPACER,.32 X.75 X 1.06, PM SPRING, COMP. 1/2 ID X.140 WIRE X GRIP, FOAM, 3/4 ID X 6 X X14 4 BOLT, 5/16-18 X 1-3/4 GD5 YZ X6 4 BOLT, 3/8-16 X 3/4 GD5 YZ NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X10 3 BOLT, 5/16-18 X 1-1/4 GD5 YZ A 1 WELD, BRAKE SHAFT - BLK A 2 LINK, BRAKE LOCK - BLK WASHER, 5/16 USS NUT, 5/16-18 HEX NYLOCK FLANGE COLLAR, 5/16 SET SPACER,.33 X.50 X.25, CZ 18-1 SWITCH (SEE ELECTRICAL GROUP) X12 2 BOLT, 5/16-18 X 1-1/2 GD5 YZ NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL SPRING, EXTENSION,.521 X 4.12, BLACK CABLE, PARKING BRAKE, 32" NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) Footnotes

42 Rear Suspension Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

43 Rear Suspension Group REF NO PART NO. QTY. DESCRIPTION X16 2 BOLT, 3/8-16 X 2 GD5 YZ X28 2 BOLT, 3/8-16 X 3-1/2 GD5 CZ NUT, 3/8-16 HEX SIDE LOCK NUT, 1/2-13 HEX NYLOCK FLANGE X52 2 BOLT, 1/2-13 X 6-1/2 GD8, YZ WASHER, 1/2 SAE NUT, 5/16-18 HEX NYLOCK FLANGE SPACER,.34 X 1.54 X.25, PL SCREW, 5/16-18X1, PHILLIPS HD. BZ SPACER,.52 X 1.00 X SPACER,.39 X 2.00 X 1.35, PM WASHER-3/8 FENDER GREASE FITTING, 1/4-28 STRAIGHT BUSHING, FLANGE SHOCK / SPRING ASSEMBLY, OE B 1 WELD, TRANSMISSION CARRIAGE, IS3200 -RED NUT, 3/8-16 HEX NYLOCK FLANGE Footnotes

44 Deck Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

45 Deck Lift Group REF NO PART NO. QTY. DESCRIPTION SPACER,.52 X 1.00 X.75, CZ (Qty: 3-72" Models) EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ (72" Models) X6 2 PIN, COTTER, 1/8 X 3/ X24 2 BOLT, 1/2-13 X 3 GD5 CZ NUT, 1/2-13 HEX NYLON LOCK X16 1 BOLT, 1/2-13 X 2 GD5 CZ (Qty: 2-72" Models) X20 2 BOLT, 1/2-13 X 2-1/2 GD5 CZ NUT, 1/2-20 HEX JAM NUT, 3/8-16 HEX SERRATED FLANGE (72" Models) ADJUSTER, DECK HANGER WASHER,.390 X 1.50 X.109, CZ PIVOT BLOCK, PLASTIC ROD, DECK LIFT, EXTERNAL THRD, BAR, DECK LIFT, 17.75" ROD, SUSPENSION LINK, IS700, CZ SPACER,.52 X 1.00 X.22, PM, CZ A 1 PEDAL, FOOT - BLK PEDAL, RUBBER SPACER,.52 X 1.00 X.88, PM, CZ WASHER, 1/2 SAE (Qty: 5-72" Models) X22 2 BOLT, 1/2-13 X 2-3/4 GD5 CZ NUT, 1/2-13 HEX NYLOCK FLANGE (Qty: 4-72" Models) X10 2 BOLT, 3/8-16 X 1-1/4 GD5 CZ NUT, 3/8-16 HEX NYLOCK FLANGE (Qty: 7-72" Models) BOLT, 3/8-16 X 3/4, PLT W/PATCH GREASE FITTING, 1/4-28 STRAIGHT COLLAR, 5/8 SPLIT SPRING-EXT,.740 ODX2.025LGX.072WR, BLK EYE BOLT, 3/8-16 X 8, 3THRD, 1EYE, CZ GRIP, FOAM,.475 X 4.35 X SPRING-EXT, ODX13.25LGX.218WR, BLK (Qty: 3-72" Models) PIN, HITCH, 1/2 X 2.00 OAL, YP WASHER, 1/4 FENDER X5 2 BOLT-1/4-20 X 5/8 GD5 CZ NUT, 1/4-20 HEX NYLOCK FLANGE X4 1 PIN, CLEVIS, 1/4 X 1/2, PLATED WASHER, 3/8 SAE X22 4 BOLT, 3/8-16 X 2-3/4 GD5 CZ JOINT-BALL THD.500ID, CLR ZINC A 1 WELD, ROD DECK LIFT, IS700 - BLK A 1 WELD, DECK HEIGHT LINK, IS700 - BLACK Footnotes

46 Deck Lift Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

47 Deck Lift Group REF NO PART NO. QTY. DESCRIPTION A 2 PLATE, PIVOT BLOCK SUPPORT - BLK B 1 WELD, DECK LIFT SHAFT - RED (61) (61" Models) NUT, 1/2-13 HEX JAM (72" Models) B 2 WELD, DECK LIFT LEVER, LH - RED (S/N: & Below) B 2 WELD, DECK LIFT LEVER, RH - RED (S/N: & Below) A 1 WELD, REAR LIFT - LH - BLK BUSHING, 1.00 X 1.13 X 1.38, PLASTIC SPACER,.52 X 1.00 X 1.00 (61" Models) SPACER,.52 X 1.00 X.44, CZ A 1 WELD, REAR LIFT - RH - BLK NUT, 3/8-16 HEX NUT, 3/8-16 HEX NYLON LOCK B 1 WELD, DECK LIFT SHAFT, 72 (72" Models) B 2 WELD, DECK LIFT, LEVER, LH - RED (S/N: & Above) B 2 WELD, DECK LIFT, LEVER, RH - RED (S/N: & Above) Footnotes

48 Transaxle SERVICE PARTS - ZT5400 NOTE: Unless noted otherwise, use the standard hardware torque specification chart

49 Transaxle SERVICE PARTS - ZT5400 REF NO PART NO. QTY. DESCRIPTION X5 1 AXLE CAP, ZT5400 (Hydro-Gear P/N 53724) X2 1 KIT, FILTER (Hydro-Gear P/N 71943) X4 1 KIT, SEAL, ZT5400 (Hydro-Gear P/N 71945) X6 1 KIT, CONTROL ARM SEAL (Hydro-Gear P/N 52989) X8 1 KIT, INPUT SHAFT (BEARING AND SHAFT ONLY) (Hydro-Gear P/N 71941) X7 1 KIT, INPUT SEAL (Hydro-Gear P/N 51280) X6 1 ASSM, HUB, STANDARD AXLE TRANSMISSIONS (ZT5400) (Hydro-Gear P/N 72039) X1 1 ASSM, HUB, LONG AXLE TRANSMISSIONS (ZT5400) (Hydro-Gear P/N 72102) X5 1 KIT, AXLE SEAL (Hydro-Gear P/N 53008) Footnotes

50 Wheel & Tire Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart

51 Wheel & Tire Group REF NO PART NO. QTY. DESCRIPTION NUT, 1/2-20, FOR WHEEL BOLT SILVER TIRE ASSM, 13 X 6.5-6, PNE / TB X72 2 BOLT, 1/2-13 X 9 GD5 CZ NUT, 1/2-13 HEX NYLOCK FLANGE WASHER, 1/2 SAE DEBRIS, COVER, CASTER WHEELS BEARING ADJUSTER, SPACER, LG NUT, BEARING ADJUSTER, AXLE TIRE/WHEEL ASM, 26X , TURF SMART TIRE, FRONT, 13 X 6.5 X 6 (SV) X1 2 WHEEL ASSEMBLY, FOR 13 X 6.5 X 6 TIRES (INCLUDES BEARING AND SEALS) SX2 4 BEARING, TAPERED ROLLER (SV) (2 per tire) SX3 4 GREASE SEAL (SV) (2 per tire) X1 2 WHEEL, 12 X 9.5, SOLD, 4.063" OFFSET (SV) X2 2 TIRE, TURF SMART, 26X PLY (SV) SX4 2 BEARING, RACE (SV) (Not illustrated) Footnotes

52 Decal Group - Brand & Model S/N: & Below NOTE: Unless noted otherwise, use the standard hardware torque specification chart

53 Decal Group - Brand & Model S/N: & Below REF NO PART NO. QTY. DESCRIPTION DECAL, FERRIS, FRONT BADGE DECAL, BADGE, IS3200Z, LH DECAL, BADGE, IS3200Z, RH DECAL, 61 (61" Models Only) DECAL, 72 (72" Models Only) DECAL, FERRIS, 2.23" X 11.39" DECAL, icd CUTTING SYSTEM Footnotes

54 Decal Group - Brand & Model S/N: & Above NOTE: Unless noted otherwise, use the standard hardware torque specification chart

55 Decal Group - Brand & Model S/N: & Above REF NO PART NO. QTY. DESCRIPTION DECAL, FERRIS LOGO, SMALL DECAL, MODEL, IS3200Z DECAL, TANK, MED, LH, FERRIS DECAL, TANK, MED, RH, FERRIS DECAL, FERRIS, 2.23" X 11.39" DECAL, 61 (61" Models Only) DECAL, 72 (72" Models Only) DECAL, icd CUTTING SYSTEM Footnotes

56 Decal Group - Safety & Operation (USA Models) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

57 Decal Group - Safety & Operation (USA Models) REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY DECAL, PINCH POINT DECAL, DANGER DO NOT OPERATE W/O DEFLECT DECAL, WARNING, HAND IN BELT, ENG ONLY DECAL, MANUAL AVAIL IN SPANISH DECAL, WARNING, ROLL BAR DECAL, TRANSAXLE RELEASE, S200XT DECAL, FUEL VALVE DECAL, THROTTLE CONTROL DECAL, WARNING, FOLDING ROPS DECAL, WARNING, OVERHAND, ROPS DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, SAE 20W50 (Located on cross rail by hydraulic tanks) DECAL, FUSE LOCATION, IS2100 (Located on cross rail above fuse block) DECAL, CUT HEIGHT, IS700/ZTS DECAL, BELT AND BLADE, IS3200Z DECAL, CAUTION, FOLDING ROPS DECAL, FUEL VALVE (CAL Models only) Footnotes

58 Decal Group - Safety & Operation (Export Models) NOTE: Unless noted otherwise, use the standard hardware torque specification chart

59 Decal Group - Safety & Operation (Export Models) REF NO PART NO. QTY. DESCRIPTION DECAL, MAIN SAFETY, ANSI CE DECAL, PINCH POINT, CE DECAL, CE DANGER DECAL, DISCHARGE SAFETY, EXPORT DECAL, PARKING BRAKE SYMBOLS DECAL, WARNING, ROLL BAR, CE DECAL, TRANSAXLE RELEASE, S200XT DECAL, FUEL VALVE DECAL, THROTTLE CONTROL DECAL, SAFETY, CE ROPS (SV) DECAL, SAFETY, CE ROPS, OBS (SV) DECAL, IGNITION SWITCH DECAL, HYDRAULIC OIL, SAE 20W50 (Located on cross rail by hydraulic tanks) DECAL, FUSE LOCATION, IS2100 (Located on cross rail above fuse block) DECAL, CUT HEIGHT, IS700/ZTS DECAL, BELT AND BLADE, IS3200Z DECAL, FIRE ANSI EXPORT Footnotes

60 61" Mower Deck Group - Rollers & Casters NOTE: Unless noted otherwise, use the standard hardware torque specification chart

61 61" Mower Deck Group - Rollers & Casters REF NO PART NO. QTY. DESCRIPTION ROLLER, DECK A 1 WELD, BRACKET, ROLLER PIN - BLK SPACER,.38 X.63 X NUT, 3/8-16 HEX NYLOCK FLANGE B 1 PLATE, BRACKET, ANTI-SCALP - RED X8 7 BOLT, 3/8-16 X 1 GD5 CZ WASHER, 3/8 SAE ROLLER, SMALL B 1 WELD, ANTI-SCALP BRACKET - RED B 1 PLATE, ANTI-SCALP SUPPORT - RED BOLT,3/8-16X1.00,RD SH SQ NK,GR 5,ZC/CL X44 2 BOLT, 3/8-16 X 5-1/2, CARRIAGE, GD5, CZ X10 1 BOLT, 3/8-16 X 1-1/4 GD5 CZ Footnotes

62 61" & 72" Mower Deck Group - Deck Hangers NOTE: Unless noted otherwise, use the standard hardware torque specification chart

63 61" & 72" Mower Deck Group - Deck Hangers REF NO PART NO. QTY. DESCRIPTION B 4 BRACKET, INNER TRUNION MOUNT - RED (S/N: & Below) B 4 BRACKET, OUTER TRUNION MOUNT - RED (S/N: & Below) X20 4 BOLT, 1/2-13 X 2-1/2 GD5 CZ X12 8 BOLT, 5/16-18 X 1-1/2 GD5 CZ (S/N: & Below) PIVOT, DECK LIFT TRUNION, GREASABLE SPACER,.52 X.87 X 1.25, CZ ADJUSTER, DECK LIFT, CZ EYE BOLT, 1/2-20X6", 2.5"THRD, NUT, 1/2-13 HEX NYLOCK FLANGE NUT, 5/16-18 HEX NYLOCK FLANGE (S/N: & Below) WASHER, 1/2 SAE WASHER, 5/16 SAE (S/N: & Below) NUT, 1/2-20 HEX JAM A 4 BRACKET, INNER TRUNION MOUNT - BLK (S/N: & Above) A 4 BRACKET, OUTER TRUNION MOUNT - BLK (S/N: & Above) X12 8 BOLT, 3/8-16 X 1-1/2 GD5 CZ (S/N: & Above) WASHER, 3/8 SAE (S/N: & Above) NUT, 3/8-16 HEX NYLOCK FLANGE (S/N: & Above) Footnotes

64 61" Mower Deck Group - Housing, Covers, Spindles & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart

65 61" Mower Deck Group - Housing, Covers, Spindles & Blades REF NO PART NO. QTY. DESCRIPTION DECK SHELL W/DECALS, 61, 3200-DOM ( B) SPINDLE, ASSM, CAST IRON S 1 BLADE SET, 61 DECK (3) (SV)(Set of 3 blades) B 1 GUARD, IS3200Z, LH 61" - RED B 1 GUARD, IS3200Z, RH 61" - RED A 1 SUPPORT, DISCHARGE CHUTE - BLK A 1 PLATE, SUPPORT - BLK A 1 WELD, MOUNT, DISCHARGE CHUTE - BLK A 1 PLATE, DEFLECTOR - BLK FLAP, STRIPER, 61 DECK, IS3100 S200X CHUTE, RUBBER DISCHARGE ( ) SAFETY WALK, 9.75 X ROD, MOUNT, CHUTE 61, CZ WASHER, BLADE BOLT, 9/16" F436, CZ X14 3 BOLT, 5/8-11 X 1-3/4 GD X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE /16 PUSH-ON NUT RETAINER, STL, CZ X8 6 BOLT, 5/16-18 X 1 GD5 CZ BODY CLIP, 5/ GA MATERIAL WASHER, 5/16 SAE NUT, 5/16-24 HEX NYLON LOCK SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC X6 6 BOLT, 5/16-18 X 3/4 GD5 CZ X12 3 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ NUT, 5/16-18 HEX NYLOCK FLANGE X10 18 BOLT, 3/8-16 X 1-1/4, FLANGE, GD 5, CZ NUT, 3/8-16 HEX NYLOCK FLANGE DECK SHELL W/DECALS, 61, 3200-ANSI-EXP ( B) Footnotes

66 61" Mower Deck Group - Pulleys, Belt & Idler Arm NOTE: Unless noted otherwise, use the standard hardware torque specification chart

67 61" Mower Deck Group - Pulleys, Belt & Idler Arm REF NO PART NO. QTY. DESCRIPTION A 1 WELD, IDLER ARM - BLK X48 1 BOLT, 1/2-13 X 6 GD5 CZ X28 2 BOLT, 1/2-13 X 3-1/2 GD5 CZ X20 1 BOLT, 1/2-13 X 2-1/2 GD5 CZ X12 1 BOLT, 3/8-16 X 1-1/2 GD5 CZ X8 6 BOLT, 1/4-20 X 1 GD5 CZ SPACER,.52 X 1.00 X.50, CZ BEARING, /2", SEALED SPACER,.51 X.75 X 1.22, PM CZ SPACER, IDLER ARM, 1/2 X IDLER MOUNT,.88 HIGH SPRING, EXT, 1.5ODX12.25X.234WIRE BLK PULLEY, FLAT IDLER, 6-3/4" BELT, 5V, "EL, ARAMID, WRAP RC IDLER MOUNT PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID SPACER,.52 X 1.00 X.56, PM, CZ SHIELD, PULLEY BEARING, CZ PULLEY, SPLIT STEEL, 6.432"OB, HQ BORE SPACER,.39 X 1.00 X.25, PM, CZ SPACER,.39 X.75 X.38, PM, CZ NUT, 1/2-13 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE WASHER-3/8 FENDER WASHER, 1/2 SAE NUT, 3/8-16 HEX SERRATED FLANGE EYE BOLT, 3/8-16 X 5, 2.88THRD, 1EYE, CZ KEY 1/4 SQ X 1 1/2 LONG BUSHING, TAPERED HUB Footnotes

68 72" Mower Deck Group - Housing, Covers, Spindles & Blades NOTE: Unless noted otherwise, use the standard hardware torque specification chart

69 72" Mower Deck Group - Housing, Covers, Spindles & Blades REF NO PART NO. QTY. DESCRIPTION * DECK SHELL W/ DECALS, 72, 3200-DOM ( B - Domestic Models) * DECK SHELL W/ DECALS, 72, 3200, ANSI-EXP ( B - Ansi-Exp Models) B 1 GUARD, LH, IS3200Z-72 - RED B 1 GUARD, RH, IS3200Z-72 - RED A 1 SUPPORT, DICHARGE CHUTE, 61/72 - BLK (S/N: & Below) A 1 WELD, FRAME, CHUTE, 72 - BLK (S/N: & Below) A 1 PLATE, DEFLECTOR, 72 - BLK A 1 PLATE, SUPPORT, 72" - BLK SPINDLE, ASSM, CAST IRON ROD, MOUNT, CHUTE, 72, CZ (S/N: & Below) FLAP, STRIPER, 72 DECK S 1 BLADE SET, 72 DECK (SET OF THREE) CHUTE, DISCHARGE, BEND RUBBER (SV) (S/N: & Below)( ) SAFETY WALK, 9.75 X X10 18 BOLT, 3/8-16 X 1-1/4, FLANGE, GD 5, CZ WASHER, BLADE BOLT, 9/16" F436, CZ X14 3 BOLT, 5/8-11 X 1-3/4 GD X6 2 BOLT, 5/16-18 X 3/4, CARRIAGE X12 3 BOLT, 3/8-16 X 1-1/2 GD5 CZ (S/N: & Below) NUT, 3/8-16 HEX NYLOCK FLANGE BODY CLIP, 5/ GA MATERIAL /16 PUSH-ON NUT RETAINER, STL, CZ WASHER, 5/16 SAE NUT, 5/16-24 HEX NYLON LOCK WASHER, 5/16 F436 FLAT X8 6 BOLT, 5/16-18 X 1 GD5 CZ X10 6 BOLT, 5/16-18 X 1-1/4 GD5 CZ SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC NUT, 5/16-18 HEX NYLOCK FLANGE A 1 WELD, MOUNT, DISCHARGE CHUTE - BLK (S/N: & Above) A 1 SUPPORT, DISCHARGE CHUTE - BLK (S/N: & Above) X12 3 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ (S/N: & Above) CHUTE, RUBBER DISCHARGE (S/N: & Above)( ) ROD, MOUNT, CHUTE 61, CZ (S/N: & Above) Footnotes * If you replace the mower deck on a machine in the serial number range & Below you must also order the new discharge chute components

70 72" Mower Deck Group - Pulleys, Belt, & Idler Arm NOTE: Unless noted otherwise, use the standard hardware torque specification chart

71 72" Mower Deck Group - Pulleys, Belt, & Idler Arm REF NO PART NO. QTY. DESCRIPTION A 1 WELD, IDLER ARM, CUTTER DECKS - BLK SPACER,.52 X 1.00 X.50, CZ BEARING, /2", SEALED SPACER,.510 X.750 X 1.749, CZ SPACER, IDLER ARM, 1/2 X IDLER MOUNT,.88 HIGH SPRING, EXT, 1.5ODX12.25X.234WIRE BLK PULLEY, FLAT IDLER, 6-3/4" IDLER MOUNT (S/N: & Below) PULLEY, DEEP V-IDLER, 6.25"OD X 1/2"ID SPACER,.52 X 1.00 X.56, PM, CZ SHIELD, PULLEY BEARING, CZ SPACER,.38 X 1.13 X.781 STEP, CZ EYE BOLT, 3/8-16 X 4, 2.13THRD, 1 EYE,CZ PULLEY, 7.632"OB, HQ BORE, SPLIT STEEL KEY 1/4 SQ X 1 1/2 LONG BUSHING, TAPERED HUB X36 1 BOLT, 1/2-13 X 4-1/2 GD5 CZ X28 2 BOLT, 1/2-13 X 3-1/2 GD5 CZ X20 1 BOLT, 1/2-13 X 2-1/2 GD5 CZ X32 1 BOLT, 3/8-16 X 4 GD5 CZ X8 6 BOLT, 1/4-20 X 1 GD5 CZ WASHER-3/8 FENDER NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX SERRATED FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE BELT, 5V, "EL, LRG ARAMID, WRP, RC IDLER MOUNT,.88 HIGH (S/N: & Above) Footnotes