REAR ENGINE RIDER 42 MOWER SERIES 22

Transcription

1 Parts Manual for REAR ENGINE RIDER MOWER SERIES MODELS 1BVE CONTENTS DESCRIPTION PAGE(S) DESCRIPTION PAGE(S) WHEELS- TIRES... - FRONT END, STEERING MAIN CASE... - DIFFERENTIAL, R. H. FENDER CHAIN CASE, L.H. FENDER SMOOTH CLUTCH ASSEMBLY...-1 RAILS, LIFT ARMS, CAM LIFT CUTTING DECK, DEFLECTOR DECK COVER, BELTS, BLADE BRAKES SPINDLE ASSEMBLY... DRIVE DISC ASSEMBLY... FUEL TANK & OPERATOR S SEAT... EXHAUST MUFFLER, ENGINE... THROTTLE CONTROL... ELECTRICAL SYSTEM...- WIRING SCHEMATIC8 DECALS ACCESSORIES & ATTACHMENTS... COPYRIGHT 00 SNAPPER INC. ALL RIGHTS RESERVED (Rev. 1, 0/0/0) MANUAL No. 0

2 WHEELS - FRONT 9 1 ASSEMBLY ASSEMBLY, Front Tire & Rim (11.0 ) (Includes Items Thru ) - TIRE, Pneumatic 11 x.00- (Kenda) 1-1 RIM (For 11.0 x.0 x Tire) BEARING, Ball 1- VALVE, Air (Snap-In) 1-9 FITTING Lube 1-09 WASHER () 8 1- CAP, Hub 9 1- SEAL, Felt -8 CAP, Dust COTTER-PIN, / x 1" TUBE, Inner (For./.0 x Tire) MANUAL No. 0 MODEL R. E. RIDER SERIES

3 8 WHEELS - REAR 1 ASSEMBLY ASSEMBLY, Rear Tire & Rim (Includes Items,, & ) -8 TIRE, 1 x.0-8 (Kenda) 1-1 RIM, Ext. Wide, (For 1/.0 x 8 Tire) 1- VALVE, Air (Snap-in) 1- CLAMP, Right Hand 9- BOLT, 1/-0 x /" Lug (Grade ) () -1 BOOT, Right Hand SEAL, Oil 9-0 HUB, Rear Wheel (Right Hand) -89 CAP, Hub 11 - CAP, Hub (Left Hand) -0 HUB, Rear Wheel (Left Hand) NUT, /1- Hex Center Lock 1 1- BOLT, /1- x 1-/8" Tapered (Left Hand) BOLT, /1- x " Tapered (Right Hand) MODEL R. E. RIDER SERIES MANUAL No. 0

4 FRONT END, STEERING MANUAL No. 0 MODEL R. E. RIDER SERIES

5 FRONT END, STEERING STEERING WHEEL (for /8 shaft) (includes item ) -81 LOGO, Steering Wheel 1-8 PIN, 1/" x 1-1/" Roll -8 LATCH, Parking Brake -11 CABLE, Clutch ( long) (for & Decks) 9-0 WASHER, /8 Flat () PAD, Clutch/Brake Pedal BUSHING, Nylon PEDAL, Clutch/Brake (weldment) BEARING, Nylon () 11 - SHAFT, Steering (weldment) 1-1 BUSHING, Tie-Rod () TIE-ROD, Left Hand (9.91 long) 1-18 KING-PIN Weldment, Left Hand TIE-ROD, R. H. (9.91 long) KING-PIN, Weldment Right Hand WELDMENT, Front Axle, Wide FOOT PAD, Long () SPRING, Parking Brake WASHER, 1/ I. Dia.() 1-18 BUSHING, Nylon () 1-11 PIN, Hair - FOAM COVER, Steering Shaft 9-09 PIN, /1 x 1" Cotter 9-11 WASHER, /8 Flat () 1-8 PIN, Hair (. Dia. Wire) -881 SPACER, 1/" () RING, 1/ External Retaining (Heavy Duty) RING, / Ext. Retaining () PIN, 1/8 x /" Cotter () WASHER, /8 Flat () -1 COVER, Steering Shaft -89 SPACER, Pivot -8 STUD, Shoulder (/8- Thread) 9-08 NUT, /8- Hex Nyloc -8 CABLE, Brake (9 long) -1 CONNECTOR, Cable () SCREW, 1/-0 x /", Gr NUT, 1/-0 Hex Center Lock PIN, /1" x 1-1/" Cotter PIN, / x 1 Cotter () -0 HOLDER, Wire- Bottle SCREW, #- x 1/ Hex Washer Self-Tap () -1 BOTTLE, Water -99 PLATE, Thrust MANUAL No. 0 MODEL R. E. RIDER SERIES

6 MAIN CASE CONNECTS TO ITEM 1 ON PAGE MANUAL No. 0 MODEL R. E. RIDER SERIES

7 9 SPRING (-9) PART OF ITEM 1 MAIN CASE ITEM PART NO. DESCRIPTION 1-90 CASE, Main (Weldment) -8 BUMPER, Rear (" Models) -8 FENDER, Left Hand (See Page for Related Parts) 9-09 BOLT, /1-18 x / Hex Flange Lock, Grade () COVER, Battery -8 COVER, Solenoid -189 BRACKET, Drive Support NUT, /1-18 Flange Lock () SCREW, /1-18 x /" Hex Washer Self-Tap () - LINK, Shift (Long) ARM, Shift (Weldment) -99 BRACE, Cross LINK, Shift (Short) NUT, /1-18 Hex () ARM, Shift Handle (Weldment) SPRING, Shift Handle 1-8 ASSEMBLY, Shift Detent (Incl. spring, part no. -9) 18-9 HANDLE, Shift (Weldment) BOLT, /1-18 Shoulder 0 - KNOB, Shift Handle 1-89 LEVER, Over-Ride -0 BUSHING, Pivot WASHER, /1 Int. Tooth Lock 9-00 COTTER-PIN, / x /" -91 PIN, 1/ x 1-/" Tapered Clevis 1-9 BUSHING, Nylon - WASHER, Thrust () BUSHING, Nylon () ITEM PART NO. DESCRIPTION SCREW, /1-18 x /8" Hex Washer Self-Tap () 0 1- CLIP, Wire 1-99 WING, Rear Deck () -800 SWIVEL () 9- FASTENER, Ratchet () 9- SCREW, /1-18 x 1-1/" Self- Tapping () 9-08 SCREW, /1- x 1" Hex Head Cap () RETAINER, /1 Bolt () 9-0 SCREW, /8-1x1" Self Tap () WASHER, /1" Split Lock () NUT, /1- Hex, Grade () 0-9 ASSEMBLY, Oil Drain 1-89 GUIDE, Belt (" Models) NUT, /1- Hex Flange Lock -190 PLATE, Engine 9- HAIRPIN, / x 1-1/ () 9-9 WASHER 11/ I.D WASHER, /1 Flat 9-98 NUT, /1-18 Nyloc SCREW, /1-18 x /" Hex Head Cap () SCREW, /1- x 1-/ Hex Head Cap, Grade 0 - BRACKET, Switch SCREW, #- x 1/ Hex Washer Head, Self-Tap MODEL R. E. RIDER SERIES MANUAL No. 0

8 DIFFERENTIAL, R. H. FENDER MANUAL No. 0 MODEL R. E. RIDER SERIES 8

9 DIFFERENTIAL, R.H. FENDER 1* - ASSEMBLY, R.H. Fender Bearing & DX Bearing 9-0 SCREW, 1/-0 x /8" Hex Washer Self-Tap (1) -9 WASHER, Thrust NUT, /1- Hex Flange Lock -80 PLATE, Differential -11 SPACER, Pinion (8) -1 GEARS, Differential Pinion (8) 8 1- WASHER, Thrust 9-18 ASSEMBLY, Drive Hex Tube WASHER, Hex Insert GEAR, 11 Teeth- Pitch CHAIN, Pitch (#) 1-19 SPROCKET RING, 1-1/1 External Retaining 1-18 SPACER 1 1- CLAMP, Boot (for Hose) () BOOT, Oil Seal PLUG, Oil Fill & Check 19-9 CASE, Transmission 0-8 GASKET, Transmission Case 1* -80 FENDER, Right Hand - GEAR, Teeth- Pitch - AXLE, Long (Includes Gear) (Use Only With Short Axle #-98) -1 SPACER -98 AXLE, Short (Includes Gear) (Use Only With Long Axle #-) 1- SCREW, /1- x 1-/8" Hex Cap Special Lock (8) 1-11 O-RING, /1 () WASHER, Belleville () WASHER, /1 External Tooth Lock WASHER, /1 Flat 1 1- BOLT, /1- x -/8" Idler 9-01 SCREW, /1-18 x /8" Hex Washer Self-Tap (11) -1 GREASE, SNAPPER Transmission ( oz. Required) ASSEMBLY, Differential (Includes items,,,,,, & ) KIT, Differential (Incl.1-88, Ball Bearing & -9, Fender) KIT, Differential (Includes 1-9, Powdered Metal Bearing for item 1 and -80, Fender) *NOTE: -90 Cover & Fender Assembly is composed of items 1 & 1. MODEL R. E. RIDER SERIES MANUAL No. 0 9

10 CHAIN CASE, L.H. FENDER 1 ASSEMBLY ASSEMBLY ASSEMBLY MANUAL No. 0 MODEL R. E. RIDER SERIES

11 CHAIN CASE, L. H. FENDER 1-8 ASSEMBLY, Chain Case (Includes Items Thru 1, & 1, 1, 1, 0) -11 CASE, Sprocket (Weldment) -81 GASKET, Case Cover 1-11 WASHER, Belleville 1-0 BEARING, Ball () 1-89 SPROCKET & SHAFT 1-01 KEY, 1/8 x /8" Woodruff 8-98 COVER, Chain Case BEARING, Needle () 1-8 WASHER, Nylon Thrust () 11-0 HUB & SPROCKET (Weldment) CHAIN SCREW, #- x /8" Hex Washer Self-Tap () 1 1- PLUG, Oil Fill & Check 1-8 ROLLER RING, 1/ External Retaining ASSEMBLY, Left Hand Fender (Includes items 18 & 19) 18-8 FENDER, Left Hand 19-8 ASSEMBLY, Axle Bearing (Incl. items 0 thru ) 0-18 BEARING, Left Hand Fender 1 1- FITTING, Lube (for /1 diameter hole) -00 SEAL, Dust/Grease Axle -18 BEARING, / I. D. DX () 1-1 WASHER, Shim (As Required) 1-0 ROD, Cross-Tie 1- CLAMP, Boot () 1-08 BOOT, Oil Seal WASHER, Thrust Nylon 9 1- WASHER, Thrust 0 9- NUT, /8-18 Hex Nyloc NUT, /1- Hex Flange Lock 1-90 O-RING () -981 WASHER, Wave GREASE, SNAPPER Transmission ( oz. Required) ASSEMBLY, Left Hand Fender (Includes Left Hand Fender P.N. -98 & Ball Bearing P.N. 1-) NOTE: See Pages &1 For Illustration Of Brake Lever Assembly And Related Parts. MODEL R. E. RIDER SERIES MANUAL No. 0 11

12 SMOOTH CLUTCH ASSEMBLY See page, Item 18 MANUAL No. 0 MODEL R. E. RIDER SERIES

13 SMOOTH CLUTCH ASSEMBLY NOTE: Brake Return Replacement Kit (-119) is made up of items 11 and 1. ITEM PART NO. DESCRIPTION 1-11 ASSEMBLY, Smooth Clutch (Includes Items thru ) - HUB, Driven Disc (assembly) - DISC, Driven (rubber tire bonded to rim) 1- WASHER, Thrust -1 PLATE, Drive Disc 9-08 NUT, /1-18 Hex Flange Lock () -9 ASSEMBLY, Brake Lever (Includes Brake Lining & Rivet) RING, /8 External Retaining NUT, 1/-8 Hex Top Lock 9-9 WASHER, 1/ Flat 11-9 SPACER 9- SCREW, 1/-8 x 1" Hex Head Cap, Grade (washer face) 1-0 SPRING, Brake Return SPRING, Clutch Brake 1-1 LIFT, Yoke BEARING, Yoke () NUT, /1- Hex Center Lock () SCREW, /1- x 1" Hex Head Cap, Grade () SCREW, /8-1 x /8" Hex Washer Self-Tap 0-91 COLLAR, Yoke WASHER, /1 Flat () - ARM, Yoke 9-09 SCREW, 1/-0 x 1/" Hex Washer Self-Tap () 1- STUD (/8- thread) WASHER, /8 Internal Tooth 9- NUT, /8- Hex, Grade or B -190 BRACKET, Slide PIN, / x / Cotter 9 1- SLIDE HALF () 0 1- BOLT, /1-18 Shoulder WASHER, /1 Split Lock NUT, /1-18 Hex, Grade or B 9-0 WASHER, /8 SAE Flat () -908 ASSEMBLY, Leaf Spring MODEL R. E. RIDER SERIES MANUAL No. 0 1

14 RAILS, LIFT ARMS, CAM LIFT MANUAL No. 0 MODEL R. E. RIDER SERIES 1

15 1 RAILS, LIFT ARMS, CAM LIFT ASSEMBLY, Rear Lift Arm -00 LEVER, Height Adjustment Lift -9 RAIL, Left Half -88 RAIL, Right Half -18 STRUCTURE, Front Lift Arm -00 BRACE, Weldment 1-8 IDLER, -1/8 Flat () 8-9 SPINDLE, Brace (Right) SPINDLE, Brace (Left) - BRACE/IDLER Mtg. Bracket SCREW, /8-1 x 1-1/ Hex -1 PIVOT 1-9 ROD, Leveling NUT, /8- Hex Top Lock () WASHER, /8 Int. Tooth Lock 1-8 GUIDE, Belt (Rod) 1-1 GUIDE, Belt, RER (Weldm t) QUADRANT, Lift Lever KEY, /1 x /8" Woodruff 0-90 RING, / Retaining NUT, #- Hex Nyloc SCREW, /8-1 x /" Tap () 9-0 NUT, /8-1 Hex Center Lock () 9-01 SCREW, /8-1 x /" Hex () 9-99 NUT, /8-1 Hex Nyloc -800 SWIVEL, Adjustable () WASHER, /8 Int. Tooth Lock NUT, /8- Hex Lock PIN, /1 x /" Roll RING, Red () SCREW, /1-18 x 1/" Tap () -1 SUPPORT, Rod 1-8 RING, Retaining () 1-08 RING, Blue () -8 GRIP, Height Adjustment Lever 1- ECCENTRIC, Leveling 1-9 BOLT, /8- x /" Shoulder 8-99 ARM, Front Lift (Left Side) BOLT, /8-1 x 1 Hex Flange Lock, Grade BOLT, /1-18 x /8" Hex () 1-91 SPRING, Extension 1- SPRING, Latch 9-0 COTTER-PIN, /1 x 1-1/" () -181 LATCH Weldment -8 GRIP, Lift Latch 1-1 PIN, 1/ x 1-1/" Clevis 9-00 COTTER-PIN, 1/1 x /" 8 9- HAIRPIN, / x 1-1/ () 9-88 ADJUSTER, Chain () WASHER, /8 Flat WASHER, / Flat () 1- SPACER, / I.D. () 1- PULLEY, O.D. () - NUT, /-1 Hex Jam Lock () -0 DECAL, Blade ON/OFF 9-01 BOLT, /1-18 x /8 Self-Tap -8 GUIDE, Belt ASSEMBLY, Clutch Plate 9-1 CABLE, No-Reverse-In-Mow BOLT, #- x 1 Flat Head Square Neck MODEL R. E. RIDER SERIES MANUAL No. 0 1

16 CUTTING DECK ASSEMBLY (page 1 of ) * * * NOTE: THE HEADS OF THESE FASTENERS ARE LOCATED INSIDE THE DECK. MANUAL No. 0 MODEL R. E. RIDER SERIES 1

17 CUTTING DECK ASSEMBLY (page of ) ITEM PART NO. DESCRIPTION 1 - WELDMENT, Deck -1 ASSEMBLY, Side Chute (Includes Decal, Item 1) -98 ASSEMBLY, Spindle () -91 BLADE, 1 Standard Lift () 1-18 SPRING, Belt 1-0 ROD, Idler -801 MOUNT, Handle 8-8 GRIP, Handle 9-0 ASSEMBLY, Spindle Ring () -9 WHEEL, Gage () 11-8 POST, Anti-Scalp () -9 BOLT, Gage Wheel, /8-1 x -/8 Hex Head Shoulder () DECAL, Caution 1-81 DECAL, Danger NUT, /8-1 Hex Flange Lock () BOLT, /1-18 x / Short Neck Carriage, Grade () 1-90 STAND-OFF, -1/ long, /1-18 top, /8-1 bottom threads () NUT, /8-1 Hex Flange Lock () 19-9 WELDMENT, Blade Engage Lever SCREW, #- x 1 Hex Washer Self-Tap, Grade SWITCH, Deck Interlock (NO) 9-00 WASHER, 1/ Flat 9-00 PIN, / x / Cotter 1-0 WASHER, Cone () 9-08 SCREW, /8- x 1 Hex Head Cap, Grade 1-0 RING, Tolerance () 1- SPACER () RETAINER, /1 Bolt () WING-NUT, /1-18 Lock () WASHER, /1 Flat () NUT, /8-1 Hex Center Lock () 9-9 WING-NUT, /8-1 Nyloc () 9-18 SCREW, /8-1 x 1-1/ Hex Head Cap, Grade () - HANDLE, Blade Engagement 9-19 PIN, /1 x 1 Clevis -8 SPRING, Torsion 9-0 PIN, / x 1/ Cotter SCREW, 1/-0 x /8 Hex Washer Self-Tap () NOTE: DECK ASSEMBLY IS CONTINUED ON THE FOLLOWING TWO PAGES. MODEL R. E. RIDER SERIES MANUAL No. 0 1

18 CUTTING DECK ASSEMBLY (page of ) *NOTE: SOME PREVIOUSLY ASSEMBLED COMPONENTS SUCH AS DECK, IDLERS, BELT GUIDES AND THE HEIGHT ADJUSTMENT ASSEMBLY ARE NOT SHOWN HERE IN ORDER TO CLARIFY PLACEMENT OF COMPONENTS IN THIS ASSEMBLY ** 9 9 ASSEMBLY* See Page 1, Item **NOTE: THIS SHOULDER BOLT, INTERNAL TOOTH LOCK WASHER & LEVELING ECCENTRIC ARE SHOWN ON PAGE 1 AS ITEMS, &. MANUAL No. 0 MODEL R. E. RIDER SERIES 18

19 CUTTING DECK ASSEMBLY (page of ) 9 -- ASSEMBLY, Rail (See Pages 1 & 1 for Parts Breakdown) 0 - PEDAL, Blade Stop Control 1-8 ARM, Idler -800 SWIVEL, Adjustable (with /1-18 internal thread) -1 CLIP, Cable 1-8 SPRING, Pedal 9-00 BOLT, /1-18 x /8 Hex Flange Lock () 1-00 RING, External Retaining () -9 EYE-BOLT, /1-18 x 8 9- HAIRPIN, / x 1-1/ NUT, /1-18 Hex Flange Lock () NUT, /8- Hex Center Lock WASHER, I. D. Nylon () 1- BOLT, /8- x 9/1 Shoulder 9-00 WASHER, 1/ Flat () -1 SPRING, Return -9 SPRING, Latch 9-11 WASHER, /8 Flat - SPRING BRAKE PAD NUT, 1/-0 Hex Flange Lock BOLT, 1/-0 x 1/ Hex Flange Lock () 0-88 BUSHING, /8 Snap Plastic 1-98 NUT, 1/-0 Hex Nyloc -8 LINK, Spindle Brake 9-0 PIN, 1/1 x 1/ Cotter 9-1 BOLT, 1/-0 x / Round Head Square Neck, Grade 9-1 NUT, 1/-0 Hex, Grade or B NOTE: DECK ASSEMBLY IS CONTINUED FROM THE PREVIOUS THREE PAGES. MODEL R. E. RIDER SERIES MANUAL No. 0 19

20 DECK COVER, BELTS, BLADE BRAKE Page 1, item Page 18, item MANUAL No. 0 MODEL R. E. RIDER SERIES 0

21 DECK COVER, BELTS, BLADE BRAKE 1-8 COVER, Spindle -9 PULLEY, Seam Welded Idler 9-09 WINGNUT, /1-18 () 9-9 WASHER, 11/ x 11/1 x 1/1 Flat () 9-1 SCREW, 1/-0 x /8" Hex Washer Head, Self-Tap () -91 COVER, Lift Quadrant -899 DECAL, Brake Operation 8 - NUT, /-1 Hex Jam Lock 9-88 BELT, (1.8, L Section) 9-0 WASHER, /8 Flat () WASHER, 1/ Flat 9-00 COTTER-PIN, / x / () PIN, 1/ x 1-/8 Clevis SPACER 1-8 ASSEMBLY, Brake Band 1-8 DRUM, Brake 1 1- SPACER, / I.D WASHER, / Flat () RING, External Retaining () WASHER, I.D., Nylon () 1 1- SPACER () -8 WELDMENT, Brake Arm NUT, /8- Hex Center Lock -9 LINK 9-0 SCREW, /8- x 1 Hex Head Cap Grade 9-99 NUT, /8-1 Hex Nyloc () 9-11 WASHER, /8 Flat () PULLEY, -1/8 Flat Idler SCREW, /8-1 x 1-1/ Hex Head Cap Grade () MODEL R. E. RIDER SERIES MANUAL No. 0 1

22 SPINDLE ASSEMBLY 1 ASSEMBLY ASSEMBLY, Spindle Housing (Includes items thru 8) 1-91 RING, 1. Internal Retaining () 1-1 BEARING, Spindle () -89 HOUSING, Spindle (weldment) FITTING, Lube -9 HOLDER, Blade 1-0 WASHER, Spindle 8-0 SPINDLE (9. Length) RING, Tolerance MANUAL No. 0 MODEL R. E. RIDER SERIES

23 DRIVE DISC ASSEMBLY WELDMENT,. O. D. Drive Disc 9-01 SCREW, /8-1 x /8" Set () 1-0 KEY, 1/ Square x MODEL R. E. RIDER SERIES MANUAL No. 0

24 FUEL TANK & OPERATOR S SEAT EXHAUST MUFFLER, ENGINE 1 ITEM PART NO. DESCRIPTION 1-89 SEAT, Operator (DeLuxe Back) - ASSEMBLY, Fuel Tank (Incl. item ) 1-9 CAP, Fuel Tank (With Gauge) 1- VALVE, Fuel Shut-Off 1- CLAMP, Fuel Line () -08 HOSE, Fuel (" Long) 1-9 FILTER, Fuel (In-Line) 8-9 BRACKET, Tank (For Briggs 1 HP) SCREW, /1-18 x /8" Self-Tap () - BRACKET, Fuel Tank (Rear) BOLT, /1-18 x 1/" Hex Fl. Lock () -191 KNOB, Seat Adjusting () SPACER, /1 () SCREW, /1-18 x 1/ Hex Self-Tap 1 - HOSE, Fuel (-1/" Long) SWITCH, Seat (Normally Closed) 1 THESE ITEMS FURNISHED WITH ENGINE ITEM PART NO. DESCRIPTION 1-81 MUFFLER (Briggs 1 HP Engine) ENGINE SPECIFICATIONS MODEL: 0 TYPE: 11E1 MANUAL No. 0 MODEL R. E. RIDER SERIES

25 THROTTLE CONTROL CONTROL, Throttle (. long) (Briggs Engines) SCREW, #- x 1/" Hex Washer Head, Self-Tap (Torx) () -0 PLATE, Throttle Control -18 CONTROL, Choke 9-09 SCREW, 1/-0 x /8" Self-Tap () 9-01 NUT, /8- Hex WASHER, /8 Internal Tooth Lock MODEL R. E. RIDER SERIES MANUAL No. 0

26 ELECTRICAL SYSTEM (For 1HP Briggs Engine) TO ITEM 8 1 N 1 O J I * TO ITEM 1 TO ITEM 0 TO ITEM 11 H TO ITEM G TO ITEM (D, E, F) TO ITEM (A) O L H 1 L M K L N 1 L 18 H M G K 1 8 TO ITEM *NOTE: GROUNDING PLUNGER (GROUNDS MAGNETO UNLESS FULLY DEPRESSED) MANUAL No. 0 MODEL R. E. RIDER SERIES

27 ELECTRICAL SYSTEM (For 1HP Briggs Engine) 1-0 KIT, V Dry Charge Battery SOLENOID - HARNESS, Starter Wiring (Briggs) -9 HARNESS, Ignition Wiring (Briggs) 1-18 HOLDER, Fuse (Includes Fuse) FUSE ( AMP) -80 INTERLOCK Module (Briggs) -88 HARNESS, Deck Interlock Wiring SWITCH, Deck Interlock (Normally Open) 9 1- COVER, Battery Cable 1-9 CABLE, Positive (Red) (1 Long) 11-9 SWITCH, Ignition (Indak #GA) WASHER, /8 Internal Tooth Lock NUT, /8- Hex KEY, Switch () SCREW, 1/-0 x 1/"Hex Washer Self-Tap () RETAINER, 1/ Bolt () 1-80 HARNESS WIRE (Operator Presence Control) (Briggs) WASHER, 1/ Internal Tooth Lock () 19-1 SCREW, 1/-0 x /8" Hex Head Cap, Grade () 0-80 CABLE, Negative (1 Long) NUT, 1/-0 Hex Grade or B TIE, " Long Cable () 9-0 NUT, 1/-0 Hex Center Lock, Grade or B () -88 SWITCH, Operator Presence Control (OPC) Traction (NO/NC) -911 SWITCH, Seat (Normally Closed) G. MAGNETO SHORTING BLOCK RIB WHITE WIRE H. BATTERY WIRE GROUNDS TO FRAME 1 I. ALTERNATOR CHARGING WIRE NOTE: Before plugging in be sure that The white wire is aligned with the plastic rib. J. STARTER TERMINAL MODEL R. E. RIDER SERIES MANUAL No. 0

28 WIRING SCHEMATIC WIRING SCHEMATIC FOR 1 HP BRIGGS ENGINE MANUAL No. 0 MODEL R. E. RIDER SERIES 8

29 DECALS DECAL, SNAPPER -0 DECAL, Warning, Safety Instruction -0 DECAL, Chute/Deflector 1-91 DECAL, Caution, Battery -81 DECAL, Danger (Heavy Adhesive) DECALS (Continued On Next Pages) MODEL R. E. RIDER SERIES MANUAL No. 0 9

30 DECALS (continued) DECAL, Brake/Blade Operation -81 DECAL, No Mow in Reverse DECAL, Battery Storage DECAL, Caution, Fuel -0 DECAL, Blade Engagement ( ) DECALS (Continued On Next Page) MANUAL No. 0 MODEL R. E. RIDER SERIES 0

31 11 DECALS (continued) DECAL, B&S Air Index/Emission Label -9 DECAL, Inch 1-0 DECAL, Fuel Routing 1-0 DECAL, Fuel Shut-Off 1 - DECAL, OPEI Ride On 1-90 DECAL, Patent Numbers DECAL, Caution Tag DECALS (Continued From Previous Two Pages) MODEL R. E. RIDER SERIES MANUAL No. 0 1

32 Parts Manual for REAR ENGINE RIDER MOWER SERIES MODELS 1BVE SNAPPER REAR ENGINE RIDER ACCESSORIES PART NO. DESCRIPTION OF KIT MODELS USED ON Ninja Mulching...All Deck Rear Engine Riders Single Bag Collector ( Bu.)...All Deck Rear Engine Riders Thatcherizer 8...All Deck Rear Engine Riders Dozer Blade ( Blade)...All Deck Rear Engine Riders Tire Chains...All Deck Rear Engine Riders Dump Cart ( Cu. Ft.)...All Deck Rear Engine Riders IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. COPYRIGHT 00 SNAPPER INC. ALL RIGHTS RESERVED MANUAL No. 0 (Rev. 1, 0/0/0) Printed in U. S. A.