Mfg. No: IS600Z Series w/ 44" Rear Discharge

Transcription

1 Parts Manual Mfg. No: IS600Z Series w/ 44" Rear Discharge Copyright Briggs and Stratton. All Rights reserved 20-Sep-2017

2

3 Model Components Table Of Contents Page 44" & 48" Mower Deck - Hanger Chains " & 48" Mower Deck - Rollers " (S/N & Below) & 48" (S/N & Below) Mower Deck - Pulleys, Belt & Idler Arm " Mower Deck - Housing, Covers, Spindles & Blades - Rear Discharge " Mower Deck (S/N: & Above) - Pulleys, Belt & Idler Arm CE Guarding - 44" Rear Discharge Mower Deck (S/N: & Above) CE Guarding - Frame, Parking Brake & Engine Compartment S/N: & Above Decal Group - Brand & Model S/N: & Below Decal Group - Brand & Model S/N: & Above Decal Group - Safety & Operation Export Models Deck Lift Group Electrical Group - S/N: & Below Electrical Group - S/N: & Above Electrical Schematic - Charging Circuit - B&S S/N: & Above Electrical Schematic - Charging Circuit - S/N: & Below Electrical Schematic - Cranking Circuit - B&S S/N: & Above Electrical Schematic - Cranking Circuit - S/N: & Below Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - B&S S/N: & Above Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - S/N: & Below Electrical Schematic - PTO Clutch Circuit - B&S S/N: & Above Electrical Schematic - PTO Clutch Circuit - S/N: & Below Engine & PTO Group Evap Canister Group - CAL Models (S/N: All); Other Models (S/N: & Below) EVAP Group - S/N : & Above Fuel Supply Hose & Tank Replacement Parts Group Fuel Tank & Mount Group Hydraulic Group Instrument Control Panel Group Main Frame & Front Suspension Group Motion Control Group - Control System Motion Control Group - Handles & Dampeners Parking Brake Group Rear Bumper & ROPS Group Rear Suspension Group Seat Mount & Floor Group Spindle SERVICE PARTS Transaxle Drive Group Transaxle SERVICE PARTS - ZT3400 ( _ ) Wheel & Tire Group Torque Specification Chart Copyright Briggs and Stratton. All Rights reserved 3 20-Sep-2017

4 44" & 48" Mower Deck - Hanger Chains Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved 4 20-Sep-2017

5 44" & 48" Mower Deck - Hanger Chains REF NO PART NO QTY DESCRIPTION NUT, 3/8-16 HEX NYLOCK FLANGE X14 6 BOLT, 3/8-16 X 1-3/4 GD WASHER, 3/8 SAE NUT, 3/8-16 HEX SERRATED FLANGE NUT, 3/8-16 HEX JAM X3 2 CHAIN, 5/16 GD30, 3 LINKS X2 2 CHAIN, 5/16 GD30, 2 LINKS CLEVIS, 5/16-18, 3/8 PIN HOLE, CLR ZINC PIN, 3/32 X.750, COT, ZINC/CLEAR X9 2 PIN, CLEVIS, 3/8 X 1-1/8, CZ X16 2 BOLT, 5/16-18 X 2 GD5 TFL NUT, 5/16-18 HEX JAM X16 2 BOLT, 3/8-16 X 2 GD5 YZ Copyright Briggs and Stratton. All Rights reserved 5 20-Sep-2017

6 44" & 48" Mower Deck - Rollers Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved 6 20-Sep-2017

7 44" & 48" Mower Deck - Rollers REF NO PART NO QTY DESCRIPTION WHEEL WIDE 3.88 DIA 0.531ID POLY BOLT-WHEEL 3/8-16X THRD WASHER-0500(0.51IDX0.87ODX.06THK) BLK NUT, 3/8-16 HEX SIDE LOCK Copyright Briggs and Stratton. All Rights reserved 7 20-Sep-2017

8 44" (S/N & Below) & 48" (S/N & Below) Mower Deck - Pulleys, Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved 8 20-Sep-2017

9 44" (S/N & Below) & 48" (S/N & Below) Mower Deck - Pulleys, REF NO PART NO QTY DESCRIPTION WASHER,.53 X 1.50 X X20 2 BOLT, 1/2-13 X 2-1/2 GD5 YZ A 1 WELD, IDLER ARM - BLK (12.00) WASHER, 3/4 BELLEVILLE NUT, 3/4-16 HEX WASHER, 1/2 USS WASHER, 1/2 SAE X28 1 BOLT, 1/2-13 X 3-1/2 GD5 YZ NUT, 1/2-13 HEX NYLON LOCK NUT, 1/2-13 HEX SIDE LOCK X40 1 BOLT-1/2-13 X 5 GD5 YZ EYE BOLT, 3/8-16 X 6, 3.0 THREAD NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX JAM BELT, 5V-SEC, " EL, ARAMID, WRPD, RC -(48" Mower Decks) GREASE FITTING, 1/4-28 STRAIGHT X10 3 KEY, 1/4 SQ X 1-1/ SPRING-EXT, 1.04 ODX10.535LGX.148WR, BLK SPACER,.52 X 1.25 X.70, CZ SPACER,.52 X 1.00 X.44, CZ SPACER,.52 X 1.00 X.88, CZ BUSHING, FLANGE SPACER,.52 X 1.00 X SHIELD, PULLEY BEARING PULLEY, 5.540OB X 3985ID, SINGLE B-SEC PULLEY, IDLER, 5" OD, 1"FACE, 5.75 FL 27 1 USE PULLEY SHIELD X22 1 BOLT, 1/2-13 X 2-3/4 GD5 YZ *PULLEY, FLAT IDLER, 6-3/4" -*If not present, order washer and shield BELT, 5V-SEC, " EL, ARAMID, WRPD, RC -(44" Mower Decks) Copyright Briggs and Stratton. All Rights reserved 9 20-Sep-2017

10 44" Mower Deck - Housing, Covers, Spindles & Blades - Rear Discharge Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

11 44" Mower Deck - Housing, Covers, Spindles & Blades - Rear Discharge REF NO PART NO QTY DESCRIPTION DECK SHELL W/ DECALS, 44RDCE, IS600ZCE ( B) -(SV) A 2 BAFFLE, FRONT DISCHARGE, 44RD - BLK B 1 WELD, MULCH BAFFLE, 44RD - RED -(S/N: & Below) A 1 BAR, RETAINING, 44RD - BLK SAFETY WALK, 4.00 X FLAP, RUBBER, 44RD BODY CLIP, 5/ GA MATERIAL ASSM, SPINDLE, LOW PROFILE BOLT, 5/16-18 X 1 1/4 FLANGE S 1 BLADE SET, 15 (SET OF 3) -(SV)(S/N: & Below) WASHER, BLADE BOLT, 9/16" F436, CZ X14 3 BOLT, 5/8-11 X 1-3/4 GD B 1 GUARD, 44" MOWER DECK, LH B 1 GUARD, 44" MOWER DECK, RH /16 PUSH-ON NUT RETAINER, STL, CZ X8 3 BOLT, 5/16-18 X 1, CARRIAGE -(S/N: & Below) NUT, 5/16-18 HEX NYLOCK FLANGE -(Qty: 21 - S/N: & Below) WASHER, 5/16" SAE X6 12 BOLT, 5/16-18 X 3/4 GD X8 6 BOLT, 5/16-18 X 1 GD5 YZ S 1 BLADE SET, MULCH, 44 DECK (SET OF 3) -(S/N: & Above) A 1 WELD, REAR BAFFLE, 44RD, SHRT, IS600-BLK -(S/N: & Above) X6 3 BOLT, 5/16-18 X 3/4, CARRIAGE -(S/N: & Above) NUT, 5/16-18, HEX, CNTR LK,ZINC PHOS/OIL -(S/N: & Above) BUMPER, RUBBER 1/4-20 -(S/N: ) NUT, 1/4-20 HEX SERR. FLANGE -(Qty: 1 - S/N: ) BUMPER, RUBBER, 1/4-20 X 7/8" STUD -S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

12 44" Mower Deck (S/N: & Above) - Pulleys, Belt & Idler Arm Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

13 44" Mower Deck (S/N: & Above) - Pulleys, Belt & Idler Arm REF NO PART NO QTY DESCRIPTION PULLEY, 5.510OB X.985ID, SINGLE B-SEC X10 3 KEY, 1/4 SQ X 1-1/ WASHER, 3/4 BELLEVILLE CL/ZC NUT, 3/4-16 HEX BUSHING, FLANGE SPACER,.52 X 1.00 X A 1 WELD, IDLER ARM - BLK WASHER, 1/2 USS NUT, 1/2-13 HEX NYLOCK FLANGE X40 1 BOLT-1/2-13 X 5 GD5 CZ SPACER,.52 X 1.00 X.44, CZ SHIELD, BEARING, 1/2 ID X 2-7/8 OD, CZ PULLEY,IDLER,BACKSIDE,NOSEAM 6.25ODX.5ID SPACER,.52 X 1.25 X.70, PM, CZ PULLEY, IDLER, 5" OD, 1"FACE, 5.75 FL SHIELD, PULLEY BEARING, CZ WASHER,.53 X 1.50 X PULLEY, FLAT IDLER, 6-3/4" WASHER, 1/2 SAE X20 1 BOLT, 1/2-13 X 2-1/2 GD5 CZ X10 1 BOLT, CARRIAGE 1/2-13 X 1-1/4 GD X22 1 BOLT, 1/2-13 X 2-3/4 GD5 CZ X28 1 BOLT, 1/2-13 X 3-1/2 GD5 CZ SPACER,.52 X 1.00 X.75, CZ A 1 WELD, BELT GUIDE - BLK BELT, 5V, "EL, ARAMID WRPD, RC EYE BOLT, 3/8-16 X 6, 3THRD, 1EYE, CZ NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX SERRATED FLANGE SPRING-EXT, 1.04 ODX10.535LGX.148WR, BLK A 1 WELD, CLUTCH BELT GUIDE - BLK WASHER, 1/4 SAE X8 2 BOLT, 1/4-20 X 1" GD5 CZ NUT, 1/4-20 HEX NYLOCK FLANGE GREASE FITTING, 1/4-28 STRAIGHT NUT, 1/2-13 HEX SIDE LOCK Copyright Briggs and Stratton. All Rights reserved Sep-2017

14 CE Guarding - 44" Rear Discharge Mower Deck (S/N: & Above) Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

15 CE Guarding - 44" Rear Discharge Mower Deck (S/N: & Above) REF NO PART NO QTY DESCRIPTION WASHER, 5/16" SAE NUT, 5/16-18 HEX NYLOCK FLANGE X6 4 BOLT, 5/16-18 X 3/4 GD B 1 PLATE, DECK GUARD, CENTER - RED B 1 PLATE, DECK GUARD, LH - RED B 1 PLATE, DECK GUARD, CENTER - RED B 1 PLATE, DECK GUARD, RH - RED Copyright Briggs and Stratton. All Rights reserved Sep-2017

16 CE Guarding - Frame, Parking Brake & Engine Compartment S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

17 CE Guarding - Frame, Parking Brake & Engine Compartment S/N: & Above REF NO PART NO QTY DESCRIPTION SCREW, TRUSS HD TORX DR5/16-18X0.875 BLK SPRING-EXT,.500 OD X 3.50 LG X.058 WR COVER, VINYL HANDLE WASHER,WAVE,M NUT, 1/4-20 HEX SERR. FLANGE WASHER, 5/16" SAE WASHER, 3/8 SAE WASHER, 1/2 SAE NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 1/2-13 HEX NYLOCK FLANGE SPACER,.39 X 1.00 X.63, CZ GRIP, BLACK FLEXIBLE -(S/N: & Below) RHSSNB,5/16-18 X 3/4 GR5 ZINC/CLEAR X24 1 BOLT, 1/4-20 X 3 GD5 CZ NUT, 1/4-20 HEX NYLOCK FLANGE X6 12 BOLT, 5/16-18 X 3/4 GD X28 1 BOLT, 3/8-16 X 3-1/2 GD5 CZ X8 4 BOLT, 3/8-16 X 1 GD5 CZ X10 2 BOLT, 1/2-13 X 1-1/4 GD5 CZ A 1 PLATE, PULLEY GUARD, FRAME MOUNT - BLK B 2 PLATE, FAN GUARD, FRAME MOUNT - RED B 1 PLATE,DECK SHIELD,FRAME MOUNT - LH - RED B 2 PLATE,DECK SHIELD,FRAME MOUNT,FRNT - RED A 2 BRACKET, DECK SHIELD MOUNT - BRK B 2 PLATE,DECK SHIELD,FRAME MOUNT, REAR -RED B 1 PLATE, DECK SHIELD, FRAME MOUNT,RH - RED A 1 PLATE, HEAT SHIELD EU - BLK A 1 WELD, NEUTRAL LOCK, LH EU - BLK A 1 WELD, NEUTRAL LOCK, RH EU - BLK B 1 PLATE, FLOOR PAN, RIDGID IS600Z EU A 1 LEVER, BRAKE, 2500, EU - BLK A 1 WELD, BRAKE SHAFT, EU - BLK -(S/N: & Below) B 1 PLATE,SUPPORT,PARKING BRAKE,600 EU - RED A 1 WELD, BRAKE SHAFT, CE - BLK -(S/N: & Above) BOLT, 1/4-20 X 1.500, GR5, SQ, ZINC/CLEAR -(S/N: & Above) NUT, 1/4-20 HEX SERR, FLANGE -(S/N: & Above) SPACER,.25 X.38 X.63, CZ -(S/N: & Above) NUT, 1/4-20 HEX NYLON LOCK -(S/N: & Above) GRIM, FOAM, 1/4 X 1 X 4.1 -(S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

18 Decal Group - Brand & Model S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

19 Decal Group - Brand & Model S/N: & Below REF NO PART NO QTY DESCRIPTION DECAL, FERRIS, FRONT, 8.78 X DECAL, BADGE. LH, IS DECAL, BADGE, RH, IS DECAL, FERRIS, 2.23" X 11.39" DECAL, ICD CUTTING SYSTEM -(Models with 48" Mower Decks Only) DECAL, 44 -(Models with 44" Mower Decks Only) DECAL, 48 -(Models with 48" Mower Decks Only) Copyright Briggs and Stratton. All Rights reserved Sep-2017

20 Decal Group - Brand & Model S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

21 Decal Group - Brand & Model S/N: & Above REF NO PART NO QTY DESCRIPTION DECAL, FERRIS LOGO, LARGE DECAL, MODEL, IS600Z DECAL, TANK, SML, LH, FERRIS DECAL, TANK, SML, RH, FERRIS DECAL, FERRIS, 2.23" X 11.39" DECAL, 44 -(Models with 44" Mower Decks Only) DECAL, 48 -(Models with 48" Mower Decks Only) DECAL, icd CUTTING SYSTEM -(Models with 48" Mower Decks Only) Copyright Briggs and Stratton. All Rights reserved Sep-2017

22 Decal Group - Safety & Operation Export Models Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

23 Decal Group - Safety & Operation Export Models REF NO PART NO QTY DESCRIPTION DECAL, MAIN SAFETY, ANSI CE DECAL, DISCHARGE SAFETY, EXPORT DECAL, FIRE ANSI EXPORT DECAL, TRANSAXLE RELEASE, 600/ DECAL, WARNING, ROLL BAR, CE DECAL, IGNITION SWITCH DECAL, THROTTLE CONTROL DECAL, SAFETY, CE ROPS -(SV) DECAL, SAFETY, CE ROPS, OBS -(SV) DECAL, HYDRAULIC OIL, SAE 20W DECAL, CUT HEIGHT, DECAL, BELT & BLADE, IS600Z/ZTS DECAL, CE DANGER -(QTY: 2 - S/N: & Below) DECAL, PARKING BRAKE SYMBOLS Copyright Briggs and Stratton. All Rights reserved Sep-2017

24 Deck Lift Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

25 Deck Lift Group REF NO PART NO QTY DESCRIPTION HHCS, 1/4-20 X 0.625, GR5, ZINC/CLEAR NUT, 1/4-20 HEX SERR. FLANGE PIN, HITCH, 1/2 X 2.00 OAL, YP GREASE FITTING, 1/4-28 STRAIGHT BOLT, 3/8-16 X 3/4, PLT W/PATCH BUSHING, 1.00X1.13X.75, PLA BUSHING, 1.00 X 1.13 X 1.38, PLASTIC WASHER,.390 X 1.50 X.109, YZ COLLAR, 5/8 SPLIT WASHER, 3/8 SAE NUT, 3/8-16 HEX NYLOCK FLANGE X22 4 BOLT, 3/8-16 X 2-3/4 GD5 YZ WASHER, 1/2 GD9 YZ X14 4 BOLT, 1/2-20 X 1-3/4 GD8 YZ NUT, 1/2-20 HEX NYLON LOCK INSERT, BEARING A 1 WELD, PULLER BAR, IS600 - BLK NUT, 1/2-20 HEX JAM PIN, HAIR,.0915 X 1-7/ A 1 WELD, REAR LIFT - RH - IS500Z - BLK ROD, DECK LIFT, SNP CLEVIS, 1/2-20, STEEL, CLEAR ZINC A 2 PLATE, PIVOT BLOCK SUPPORT - BLK GRIP, FOAM,.475 X 4.35 X WASHER, 1/2 SAE NUT, 1/2-13 HEX NYLOCK FLANGE X22 1 BOLT, 1/2-13 X 2-3/4 GD5 YZ SPACER,.52 X 1.00 X.75, CZ RUBBER, FOOT PEDAL A 1 WELD, ROD DECK LIFT, IS700 - BLK A 1 WELD, DECK HEIGHT LINK, IS700 - BLK PIVOT BLOCK, PLASTIC A 1 WELD, HANGER, REAR, RH - BLK A 1 WELD, HANGER, REAR, LH - BLK B 1 WELD, DECK LIFT SHAFT, IS A 1 WELD, REAR LIFT - LH - IS500Z - BLK ROD, SUSPENSION LINK, IS SPACER,.52 X 1.00 X.22, CZ SPRING-EXT,.740 ODX2.025LGX.072WR, BLK CLEVIS PIN, 1/2 X 1.36 SAE STANDARD WASHER, 1/4 FENDER X4 1 CLEVIS PIN, 1/4 X 1/2, CZ A 1 PEDAL, FOOT - BLK X10 2 BOLT, 3/8-16 X 1-1/4 GD5 Copyright Briggs and Stratton. All Rights reserved Sep-2017

26 Electrical Group - S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

27 Electrical Group - S/N: & Below REF NO PART NO QTY DESCRIPTION WIRE HARNESS, C TURF,WARNER, IS600/IS700 -(B&S Engines -S/N: All; Kawasaki Engines - S/N: & Above) 2 1 USE & (Kawasaki Engines S/N: & Below) 3 1 BATTERY, WET (BCIU1, 340 CCA) BATTERY CABLE, NEGATIVE, BATTERY CABLE, POSITIVE, STRAP-BLACK RUBB SOLENOID-4 POLE 12 VOLT DC (TROMBETTA) WASHER, 5/16 LIGHT LOCK NUT, 5/16-24 JAM X6 3 BOLT, 1/4-20 X 3/4 GD5 YZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE BATTERY CABLE, POSITIVE, BREAKER-CIRCUIT 12VOLT 20AMPS W/TAB CLAMP, VINYL INSULATED FUSE, ATO 15 AMP -(SV) GROMMET, 2" ID X18 2 WIRE LOOM, 3/8 ID X 18 IN FIR TREE MOUNT, PACKARD SEAT SWITCH, MILSCO, BOLT-IN -(SV) SEAT SWITCH, MILSCO, TWIST-IN -(SV) TIE, SELF-LOCKING, 6" -(Secures wire harness to wire carrier rod) SWITCH, PLUNGER, N.O./N.C SWITCH, DP NO/NC SNAP-IN WIRE HARNESS, JUMPER, KAWI -(Kawasaki Engines S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

28 Electrical Group - S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

29 Electrical Group - S/N: & Above REF NO PART NO QTY DESCRIPTION WIRE HARNESS, MAIN, SM, ZTR X4 4 SCREW- #10-24 X 1/2 ROUND PHILLIPS 3 1 BATTERY, WET ( BCIU1, 350 CCA) BATTERY CABLE, NEG, 14, 5/16-13/ BATTERY CABLE, POS, 22, 1/4-5/ STRAP-BLACK RUBB SOLENOID, STD-BRACKET, 2-SPADE NUT,1/4-20,KEPS,CONICAL WSHR,ZC/CL NUT, #10-24 HEX NYLON LOCK X6 3 BOLT, 1/4-20 X 3/4 GD5 CZ WASHER, 1/4 SAE NUT, 1/4-20 HEX SERR. FLANGE BATTERY CABLE, POS, 22, 1/4-5/ SWITCH, DP NO/NC SNAP-IN CLAMP, VINYL INSULATED, TIE,SELF-LOCKING, 6" -(Secures wire harness to wire carrier rod) GROMMET, 2" ID X18 2 WIRE LOOM, 3/8 ID X 18 IN WIRE HARNESS, JUMPER, KAWI SEAT SWITCH, MILSCO, BOLT-IN -(SV) SEAT SWITCH, MILSCO, TWIST-IN -(SV) FUSE, ATO-15 (15 AMP) -(SV) FUSE, ATO-20 (20 AMP) -(SV) Copyright Briggs and Stratton. All Rights reserved Sep-2017

30 Electrical Schematic - Charging Circuit - B&S S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

31 Electrical Schematic - Charging Circuit - B&S S/N: & Above REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

32 Electrical Schematic - Charging Circuit - S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

33 Electrical Schematic - Charging Circuit - S/N: & Below REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

34 Electrical Schematic - Cranking Circuit - B&S S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

35 Electrical Schematic - Cranking Circuit - B&S S/N: & Above REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

36 Electrical Schematic - Cranking Circuit - S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

37 Electrical Schematic - Cranking Circuit - S/N: & Below REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

38 Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - B&S S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

39 Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - B&S S/N: & Above REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

40 Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

41 Electrical Schematic - Ign. Grounding Circuit/Op. Pres. - S/N: & Below REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

42 Electrical Schematic - PTO Clutch Circuit - B&S S/N: & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

43 Electrical Schematic - PTO Clutch Circuit - B&S S/N: & Above REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

44 Electrical Schematic - PTO Clutch Circuit - S/N: & Below Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

45 Electrical Schematic - PTO Clutch Circuit - S/N: & Below REF NO PART NO QTY DESCRIPTION Copyright Briggs and Stratton. All Rights reserved Sep-2017

46 Engine & PTO Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

47 Engine & PTO Group REF NO PART NO QTY DESCRIPTION X12 2 BOLT-HEX, 5/16-24 X 1-1/2", GD8, PHOS -(Briggs & Stratton Models) X8 1 KEY, 1/4" SQ. X 1.00" WASHER, 5/16" Internal Tooth Lock -(Briggs & Stratton Models) NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) NUT, 5/16-18 HEX NYLOCK FLANGE NUT X18 1 BOLT, 5/16-18 X 2-1/4 TFL, GD5 YZ WASHER,.34 X 1.25 X 10 GA 8 1 ENGINE, B&S COMM TURF, 1-1/8 X 4.29, 44T977 -(Models with Briggs & Stratton Commercial Turf Engines) X8 4 BOLT, 5/16-18 X 1" GRD5 YZ CLUTCH WARNER 200 FT-LB 1.13 X A KIT, CLUTCH WIRE REPAIR -(SV) BELLEVILLE WASHER, X.442 X BOLT, CRANKSHAFT, 7/16 X 2-3/4, PATCH, CZ X14 2 BOLT, 5/16-24 X 1-3/4, GD8, PHOS -(Briggs & Stratton Models) PULLEY,CRANKSHAFT,1.125ID X 5.5OD A SECT A 1 ANCHOR, CLUTCH, IS600-IS700 - BLK CLUTCH ANCHOR PAD GROMMET, 7/8" HOSE, OIL DRAIN WASHER, 5/16" SAE 20 1 ENGINE, B & S, 1-1/8X4.29 CRANK, 44Q777 -(Models with Briggs & Stratton Professional Series Engines) 21 1 ENGINE, KAWASAKI, ELEC START, FS600V -(Models with Kawasaki Engines) BOLT, HEX FLG, SER, GD5 3/8-16 X 1-1/4" PACH CZ -(Kawasaki Models) MUFFLER, RIGHT OUTLET ASSY MUFFLER, (16-20HP), KAWASAKI S50X LABEL, POWER -(Briggs & Stratton Models) SPACER, 1.13 X 1.75 X 1.03, CZ ADAPTER, Oil Drain -(Kawasaki Models) NUT, 5/16-24, TOP LOCK FLANGE, GD8 PHOS -(Briggs & Stratton Models) Copyright Briggs and Stratton. All Rights reserved Sep-2017

48 Evap Canister Group - CAL Models (S/N: All); Other Models (S/N: & Below) Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

49 Evap Canister Group - CAL Models (S/N: All); Other Models (S/N: & Below) REF NO PART NO QTY DESCRIPTION X23 1 HOSE, VAPOR, 5MM ID, LG X33P5 1 HOSE, VAPOR, 5MM ID, LG -(Briggs & Stratton Models) CNSTR, CARB, 6 GAL CLAMP, 3" ID, CUSHIONED, STAINLESS X6 2 SCREW, 1/4-20 X 3/4 ALLEN BH NUT, 1/4-20 HEX NYLOCK FLANGE A 1 PLATE, MOUNT, CANISTER, IS600 - BLK X8 4 BOLT, 5/16-18 X 1 GD5 CZ WASHER, 5/16" SAE NUT, 5/16-18 HEX NYLOCK FLANGE CLAMP, TUBE & WIRING, ID -(Briggs & Stratton Models) DUST FILTER, CANISTER -(SV) ASSEMBLY, REMOTE VENT - NO VALVE -(SV) GROMMET -(SV) X31 1 HOSE, VAPOR, 5MM ID, LG -(Kawasaki Models) Copyright Briggs and Stratton. All Rights reserved Sep-2017

50 EVAP Group - S/N : & Above Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

51 EVAP Group - S/N : & Above REF NO PART NO QTY DESCRIPTION FITTING, 3/16" TEE, BARB TYPE, HDPE X27 1 HOSE, VAPOR, 5MM ID, LG -(Models equipped with B&S Engines Only) X12 1 HOSE, VAPOR, 5MM ID, LG -(Models equipped with B&S Engines Only) X2 1 HOSE, VAPOR, 5MM ID, 2.00 LG -(Models equipped with B&S Engines Only) TIE,SELF-LOCKING, 6" -(Qty: 4 on models equipped with Kawasaki Engines) FILTER, FUEL X15 2 HOSE, VAPOR, 5MM ID, LG -(Models equipped with Kawasaki Engines Only) X21P5 1 HOSE, VAPOR, 5MM ID, LG -(Models equipped with Kawasaki Engines Only) Copyright Briggs and Stratton. All Rights reserved Sep-2017

52 Fuel Supply Hose & Tank Replacement Parts Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

53 Fuel Supply Hose & Tank Replacement Parts Group REF NO PART NO QTY DESCRIPTION CLAMP, HOSE, EXTERNAL, 1/2 - RED X25 1 Fuel Line, 25" Long (tank to filter) X13 1 WIRE LOOM, 1/2 ID, LONG -(Briggs & Stratton Models Only) X3 1 FUEL FILTER (SV) -(SV) PICKUP TUBE ASM, FUEL TANK, 22" -(SV) X5 1 1/4" Fuel Line, 5" Long -(Kawasaki Models Only) BUSHING-FUEL TANK RED RUBBER (SV) Copyright Briggs and Stratton. All Rights reserved Sep-2017

54 Fuel Tank & Mount Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

55 Fuel Tank & Mount Group REF NO PART NO QTY DESCRIPTION TANK, FUEL - LH, IS500 & IS GAUGE, FUEL, 12 (SV) -(SV) X1 1 GROMMET, FUEL GAUGE (SV) -(SV) TANK, FENDER, CITATION/ZT RH FUEL CAP, 3-1/2", MANAGED VENT OUT, 12" B 2 PLATE, BADGE - IS RED SCREW, Allen Head, #10-24 x 3/8" X8 2 BOLT, 5/16-18 X 1" GRD5 YZ WASHER, 5/16 GRADE 9, FLAT WASHER, 5/16 LOCK YZ WASHER, 3/8" GR. 9 FLAT NUT, 3/8-16 HEX NYLOCK FLANGE X10 4 BOLT, 3/8-16 X 1-1/4" GD5 YZ A 1 WELD, TANK MOUNT, LH, IS600 - BLK A 1 WELD, TANK MOUNT, RH, IS600 - BLK X6 8 BOLT, 5/16-18 X 3/4 GD5 Copyright Briggs and Stratton. All Rights reserved Sep-2017

56 Hydraulic Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

57 Hydraulic Group REF NO PART NO QTY DESCRIPTION HYDRO RES. #71328, 350 ml 1A X1 2 RESERVIOR CAP -(SV) A 1 WELD, MOUNT, TANK, HYD, LH, IS600 - BLK A 1 WELD, MOUNT, TANK, HYD, RH, IS600 - BLK TRANS, LH, ZS-KHEF-8T7C-11RX TRANS, RH, ZS-GHEF-8T7B-11 RX CLAMP, HOSE ROD, DUMP VALVE, IS600 -(Older style rods did not have a hole for the hair pin.) FITTING,#6 O-RING-1/2 HOSE BARB,STRAIGHT X2P5 2 TUBING, TYGON,.50 ID X BRAKE ARM, ZT E-CLIP, BRAKE ARM, ZT3100 & ZT BOLT,1/4-20X0.750,GR5,STD NECK,SQ,ZC/CL NUT, 1/4-20 HEX NYLOCK FLANGE NUT, 1/4-20 HEX SERR. FLANGE WASHER, 1/4 FENDER 16 - See Rear Suspension Group COLLAR, 1/4 SET -(S/N: & Below) PIN, HAIR,.0585 X 1-1/8, 1/4 EYE, YZ -(S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

58 Instrument Control Panel Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

59 Instrument Control Panel Group REF NO PART NO QTY DESCRIPTION X4 3 SCREW, ALLEN HEAD 1/4-20X.500 ZINC PHOS RING, SWITCH RETAINER SWITCH-PTO PUSH PLUG,.820X1.44 HOLE, BLACK PLASTIC O-RING, 7/8" ID X 1/16" W HOUR METER, 2 CHANNEL -(See Footnote) SWITCH, IGNITION, 6 POST KEY, IGNITION MOLDED SET -(SV) COVER, PLASTIC, SNAP ON -(SV) PLASTIC NUT -(SV) CABLE, CHOKE CONTROL, 51" (Z) NUT, 3/8-24 Hex Jam X6 2 SCREW, #10-24 X 3/4" ROUND PHILLIPS NUT, Hex, Nylon Lock, # CABLE, Throttle Control, 42" TIE, SELF-LOCKING, 6" LEVER, THROTTLE CONTROL X1 1 THROTTLE CONTROL HANDLE/KNOB -(SV) A 1 PLATE, CONTROL PANEL, IS600Z - BLK Footnotes: * When replacing this hour meter, please call our service department at ext. 709 Copyright Briggs and Stratton. All Rights reserved Sep-2017

60 Main Frame & Front Suspension Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

61 Main Frame & Front Suspension Group REF NO PART NO QTY DESCRIPTION SCREW, 5/16-18 X 1 PHILLIPS HD, BZ -(Was ) 2 1 * WELD, MAIN FRAME, IS600Z - RED NUT, 5/16-18 HEX NYLON LOCK SEAL, GREASE BEARING, TAPERED ROLLER, PIVOT BEARING-1.00 X ODX PIVOT BEARING, 1.00 X OD X SPACER,.75 X 1.00 X X52 1 BOLT, 3/4-16 X 6-1/2 YZ GD NUT, 3/4-16 HEX NYLON LOCK SHOCK, SPRING ASSEMBLY X14 2 BOLT, 3/8-16 X 1-3/4 GD WASHER, 3/8 SAE WASHER-3/8 FENDER NUT, 3/8-16 HEX NYLOCK FLANGE X32 2 BOLT, 3/8-16 X 4 GD5 YZ PAD, FRICTION X A B 2 WELD, CASTER YOKE, IS500Z - RED -(44" Models Only) 18B B 2 WELD, CASTER YOKE, EVOLUTION - RED -(48" Models Only) B 1 WELD, FRONT PIVOT, IS500Z - RED CAP, LOW PROFILE, STEEL WASHER, BELLEVILLE X NUT, 3/4-16, HEX JAM NYLON LOCK WASHER, 3/4 SAE BEARING, CUP -(SV) BOLT, 1/4-28 X 1/2, GD5 YZ Footnotes: * If frame is damaged, call ext. 709 Copyright Briggs and Stratton. All Rights reserved Sep-2017

62 Motion Control Group - Control System Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

63 Motion Control Group - Control System REF NO PART NO QTY DESCRIPTION PIVOT, CONTROL SYSTEM BEARING,.375" ID X.875" OD X.341" THK SPACER,.39 X.55 X.38, CZ A 2 LINK, CONTROL SYSTEM ARM, IS600 - BLK A 2 PLATE, CONTROL SYSTEM LOCK - BLK PLATE, CONTROL SYSTEM ARM - HT PAD, CONTROL SYSTEM PAD,.77 X 3.50 X.25, POLYURETHANE X12 2 BOLT, 3/8-16 X 1-1/2, CARRIAGE, GD5, CZ SPACER,.39 X.75 X.69, CZ BOLT, 3/8-16 X 3/8, 1/2 SHOULDER ROD, 5/16 X 8.38, LH-RH, CZ ROD, 5/16 X 7.00, LH-RH, CZ BALL JOINT 5/16-24 RH FEMALE STAMPED STL BALL JOINT 5/16-24 LH FEMALE STAMPED STL SPACER,.33 X.50 X.50, CZ WASHER, 1/2 GD9 YZ WASHER, 5/16" SAE NUT, 3/8-16 HEX NYLOCK FLANGE NUT, 3/8-16 HEX SIDE LOCK X16 2 BOLT, 3/8-16 X 2 GD5 YZ X10 6 BOLT, 5/16-18 X 1-1/4 GD5 YZ NUT, 5/16-18 HEX NYLOCK FLANGE WASHER, 3/8 GD.9 FLAT X12 4 BOLT, 5/16-18 X 1-1/2 GD5 YZ WAVE WASHER, 1/2"ID X 087"OD X.01 THK WASHER-3/8 FENDER Copyright Briggs and Stratton. All Rights reserved Sep-2017

64 Motion Control Group - Handles & Dampeners Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

65 Motion Control Group - Handles & Dampeners REF NO PART NO QTY DESCRIPTION PUSH RIVET (TREE TYPE), BLACK GUARD, RUBBER MOT CTRS - IS500Z DAMPENER, CONTROL,#(P6709/P3610) BALL STUD, 5/16 X.50,# PC-477-2) A 1 WELD, NEUTRAL LOCK - LH - IS500Z - BLK -(S/N: & Below) A 1 WELD, NEUTRAL LOCK - RH - IS500Z - BLK -(S/N: & Below) A 2 MOUNT, CONTROL ARM - BLK -(9.0" Total Length, 4 Adjustment Holes) A 1 WELD, HANDLE MOTION CONTROL LH - BLK -(S/N: & Below) A 1 WELD, HANDLE MOTION CONTROL RH - BLK -(S/N: & Below) GRIP, FOAM, 3/4" ID, 16"" LONG -(S/N: & Below) A 1 WELD, SHAFT MOTION CONTROL, LH - BLK -(S/N: & Below) A 1 WELD, SHAFT MOTION CONTROL, RH - BLK -(S/N: & Below) BEARING, FLANGE BEARING, BRONZE FLANGE, 3/4" 15 2 SEE ELECTRICAL GROUP -(S/N: & Below) X4 4 SCREW, #10-24 X 1/2" ROUND PHILLIPS -(S/N: & Below) NUT, HEX, # (S/N: & Below) X20 4 BOLT, 3/8-16 X 2-1/2" GD5 YZ X24 2 BOLT, 3/8-16 X 3" GD5 YZ BOLT, Allen Head, 3/8-16 x 1-1/ WASHER, 3/8 SAE -(Qty: 12 - S/N: & Below) SPACER,.39 X.63 X 1.50, CZ X14 4 BOLT, 5/16-18 X 1-3/4 TFL, GD5 YZ NUT, 5/16-18 HEX SERRATED FLANGE (SMALL) X14 2 BOLT, 3/8-16 X 1-3/4" GD5 YZ -(Qty: 4 - S/N: & Below) X6 4 BOLT, 3/8-16 X 3/4" GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE -(Qty: 12 - S/N: & Below) NUT, 5/16-18 HEX NYLOCK FLANGE NUT SCREW, 5/16-18X0.750, GR5, WHIZ-LOCK, ZC COLLAR, 3/8" Set FLANGED BUSHING, 3/8IDX.63ODX.8125FL ROD, NEUTRAL RETURN, CZ SPRING, REVERSE RETURN BUSHING, FLANGE 3/8ID X 7/8 LONG /32 X 1-5/8 HAIR PIN CLIP NUT, Hex, Nylon Locking, 3/ NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X10 2 BOLT, 5/16-18 X 1-1/4" GD5 YZ GRIP, FOAM, 1" ID, 16" LONG -(S/N: & Above) A 1 WELD, HANDLE MOTION CNTRL, 19.0, 1.0, LH - BLK -(S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

66 Motion Control Group - Handles & Dampeners Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

67 Motion Control Group - Handles & Dampeners REF NO PART NO QTY DESCRIPTION A 1 WELD, HANDLE MOTION CNTRL, 19.0, 1.0, RH - BLK -(S/N: & Above) A 1 WELD, NEUTRAL LOCK - LH - BLK -(S/N: & Above) A 1 WELD, NEUTRAL LOCK - RH - BLK -(S/N: & Above) A 1 WELD, SHAFT MOTION CONTROL, LH - BLK -(S/N: & Above) A 1 WELD, SHAFT MOTION CONTROL, RH - BLK -(S/N: & Above) X14 2 BOLT, 1/4 X 20 X 1-3/4 GD5 YZ -(S/N: & Above) WASHER, 1/4 SAE -(S/N: & Above) NUT, 1/4-20 Hex Nylock Flange -(S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

68 Parking Brake Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

69 Parking Brake Group REF NO PART NO QTY DESCRIPTION WASHER, 5/16" SAE SPRING, COMPRESSION, 5-1/ NUT, 5/16-18 HEX NYLOCK FLANGE NUT, 3/8-16 HEX SERRATED FLANGE NUT, 5/16-18 HEX SERRATED FLANGE (LARGE) X9 1 BOLT, 5/16-18 X 1-1/8 GD X12 2 BOLT, 5/16-18 X 1-1/2 GD5 YZ X12 2 BOLT, 3/8-16 X 1-1/2, FLANGE, GD 5, CZ WASHER, 3/8 SAE NUT, 5/16-24 HEX NYLON LOCK SPACER,.38 X.50 X.27, CZ NUT, 3/8-16 HEX NYLOCK FLANGE HHCS, 1/4-20 X 0.625, GR5, ZINC/CLEAR SPRING-COMP,.496ID X 3.00LG X.112WR GRIP, FOAM,.475 X 4.35 X A 2 LINK, BRAKE LOCK - BLK NUT, 1/4-20 HEX NYLOCK FLANGE SPACER,.32 X.50 X.83, CZ BEARING, 1/2 FLANGED, PLASTIC BALL A 1 WELD, BRAKE SHAFT, IS600 - BLK -(S/N: & Below) CABLE, PARKING BRAKE, 31" (787.9 MM) CLEVIS, 5/16-18, 5/16" PIN HOLE, STEEL X8 2 PIN-CLEVIS, 5/16 X 1 YZ PIN, HAIR,.0585 X 1-1/8, 1/4 EYE, YZ NUT, 5/16-18 HEX WASHER, 5/16 USS 27 1 SEE ELECTRICAL GROUP BOLT, 1/4-20 X 1.500, GR5, SQ, ZINC/CLEAR -(S/N: & Above) NUT, 1/4-20 HEX SERR. FLANGE -(S/N: & Above) SPACER,.52 X.38 X.63, CZ -(S/N: & Above) NUT, 1/4-20 HEX NYLON LOCK -(S/N: & Above) A 1 WELD, BRAKE SHAFT - BLK -(S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

70 Rear Bumper & ROPS Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

71 Rear Bumper & ROPS Group REF NO PART NO QTY DESCRIPTION B 1 PLATE, CARB PROTECTOR - RED PLUG, PANEL, BLACK ROPS, RIDGID, IS600 -(See Footnote) X22 4 BOLT, 1/2-13 X 2-3/4 GD5 YZ WASHER, 1/2 SAE NUT, 1/2-13 HEX NYLOCK FLANGE X1 1 HARDWARE KIT IS600 ROPS SEAT BELT, RETRACTING - ASSM - RED SCREW, 1/2-13 X 1.00 SCHS A 1 EXTENSION, SEAT BELT - BLK X10 5 **BOLT, 1/2-13 X 1-1/4 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE WASHER, 1/2 SAE B 1 WELD, BUMPER - IS600 - RED CAP, VINYL X.50 - BLK A 1 PLATE, HEAT SHIELD - BLK X8 6 BOLT, 5/16-18 X 1" GRD5 YZ WASHER, 5/16 GRADE 9, FLAT NUT, 5/16-18 HEX NYLOCK FLANGE NUT Footnotes: *Call x708 if replacing a ROPS Copyright Briggs and Stratton. All Rights reserved Sep-2017

72 Rear Suspension Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

73 Rear Suspension Group REF NO PART NO QTY DESCRIPTION WASHER,.390 X 1.50 X.109, YZ SPACER,.390 X 1.00 X 1.00, CZ WASHER, 5/16" SAE -(QTY: 8 - S/N: & Below) WASHER, 3/8 SAE -(S/N: & Above) X20 2 BOLT, 5/16-18 X 2-1/2 GD5 YZ -(S/N: & Below) X20 2 BOLT, 3/8-16 X 2-1/2 GD5 -(S/N: & Above) X22 2 BOLT, 5/16-18 X 2-3/4, GD 5, YZ -(S/N: & Below) X22 2 BOLT, 3/8-16 X 2-3/4 GD5 -(S/N: & Above) NUT, 5/16-18 HEX NYLOCK FLANGE -(QTY: 10 - S/N: & Below) X24 4 BOLT, 5/16-18 X 3 GD5 YZ SPACER,.34 X 1.54 X.25 - UHMW X12 2 SCREW, 5/16-18X1.5, FLAT HD SOC, CZ X24 2 BOLT, 3/8-16 X 3 GD5 CZ X16 2 BOLT, 3/8-16 X 2 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE -(QTY: 8 - S/N: & Below) WASHER-3/8 FENDER GREASE FITTING, 45 DEGREE X52 2 BOLT, 1/2-13 X 6-1/2 GD8, YZ NUT, 1/2-13 HEX NYLON LOCK WASHER, 1/2 SAE SPACER,.39 X 1.00 X SHOCK ABSORBER, IS SPACER,.52 X 1.00 X BUSHING, FLANGE B 1 WELD, SUSPENSION CRADLE, IS600 - RED WRENCH, SPANNER, CZ GREASE FITTING, 1/4-28 STRAIGHT Copyright Briggs and Stratton. All Rights reserved Sep-2017

74 Seat Mount & Floor Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

75 Seat Mount & Floor Group REF NO PART NO QTY DESCRIPTION MNT, VBRTN, RBBR B 1 PLATE, FLOOR PAN, RIDGID IS600Z - RED B 1 PLATE, FLOOR PAN, REMOVABLE. IS600 - RED NUT, 5/16-18 HEX NYLOCK FLANGE WASHER, 5/16 F436 FLAT X8 2 BOLT, 5/16-18 X 1 GD5 YZ WASHER, 3/8 SAE X48 2 BOLT, 3/8-16 X 6 GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE SEAT, NO ARM REST 10A ARMREST KIT -(SV) 10B SPRING, EXTENSION, SEAT ADJUSTMENT (BLK OR SLVR) -(SV)(Not an illustrated part.)<br/>(3-1/2" Total unstretched length) 10C X1 1 SEAT RAIL, KIT, RH AND LH -(SV) ASSM, SEAT PLATE W/DECALS - IS600Z ( B) -(USA Models - S/N: & Below) X10 1 BOLT, 5/16-18 X 1-1/4, CARRIAGE YZ NUT, 5/16-18,GR8, HEX, CNTR, LK, ZINC/CL KNOB-INT THR ARM 2.12WD 1.06LG SAFETY WALK, FLOOR REST, 6.00 X SAFETY WALK, FLOOR PLATE, S50X, 10X X8 2 BOLT, 5/16-18 X 1, CARRIAGE ASSM, SEAT PLATE W/DECALS, IS600 ANSI-EXP ( B) -(Export Models - S/N: & Below) SEAT, XB-180, NO LOGO, BLACK -(CE Models Only) B 1 PLATE, SEAT BELT GUARD - IS600 - RED -(CE Models Only) J-BOLT, 1/4-20 X 1-1/2, CZ -(CE Models Only) NUT, 1/4-20 HEX SERR. FLANGE -(CE Models Only) ASSM, SEAT PLATE W/DECALS, IS600Z-DOM ( B) -(USA Models - S/N: & Above) ASSM, SEAT PLATE W/DECALS, IS600Z-EXP ( B) -(Export Models - S/N: & Above) Copyright Briggs and Stratton. All Rights reserved Sep-2017

76 Spindle SERVICE PARTS Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

77 Spindle SERVICE PARTS REF NO PART NO QTY DESCRIPTION SPINDLE, ASSM, ALUMINUM (Nut and Washer Sold Seperately) (Includes items # ) FITTING, 1/8 NPT STR, SHORT TRASH SHIELD BEARING,.98 X 2.44 X FITTING, RELIEF, 1-5 PSI HOUSING, SPINDLE SPACER, 1.00 X 1.25 X SPINDLE SHAFT Copyright Briggs and Stratton. All Rights reserved Sep-2017

78 Transaxle Drive Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

79 Transaxle Drive Group REF NO PART NO QTY DESCRIPTION BELT, A-SEC, "EL, WRAPPED, ARAMID PULLEY, IDLER, SINGLE FLG 4"OD X 1/2"ID SPACER,.52 X 1.00 X.22, PM, CZ SPACER, IDLER ARM, 1/2, PM A 1 WELD, ARM, PUMP DRIVE IDLER - BLK BEARING, BALL, AXLE SPACER,.52 X.84 X 1.53, PM X40 1 BOLT, 1/2-13 X 5" GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE PULLEY-IDLER-V, 4.85OB,.38ID,.94W,STL X20 1 BOLT, 3/8-16 X 2-1/2" GD5 YZ NUT, 3/8-16 HEX NYLOCK FLANGE PULLEY, IDLER-V, 4.0 X.38, STL X24 1 BOLT, 3/8-16 X 3" GD5 YZ SPACER, Shoulder WASHER, 3/8" USS SPRING-EXT, 1.25OD X 9.3LG X.142WR, BLK EYE BOLT, 3/8-16 X 5, 2.88THRD ( ) NUT, 3/8-16 Hex Large Serrated Flange SHIELD, PULLEY BEARING, CZ SHIELD, BEARING PULLEY, 3/8ID, CZ SPACER,.39 X 1.00 X.25, PM, CZ Copyright Briggs and Stratton. All Rights reserved Sep-2017

80 Transaxle SERVICE PARTS - ZT3400 ( _ ) Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

81 Transaxle SERVICE PARTS - ZT3400 ( _ ) REF NO PART NO QTY DESCRIPTION X3 - KIT, FAN & PULLEY - -HG# X5 - FAN, HG# X6 - KIT, PULLEY HG# X4 - KIT, INPUT SHAFT (BEARING AND SHAFT ONLY) -HG# X2 - KIT, SEAL - -HG# X1 - KIT, SEAL, AXLE -HG# X1 - FILTER, OIL, -HG# X5 - BEARING, 6205M, -HG# X12 - KIT, CHARGE PUMP, -HG# X2 - SEAL, CONTROL ARM, 18X32X7, -HG# X3 - OUTPUT SHAFT SEAL, 17X40X7 -HG# X4 - RING, RET 2.06 INT, -HG# X8 - ASSM, HUB -HG# X7 - AXLE CAP, -HG# Footnotes: (All part identified with ref # 5 are included in the Seal Kit.) Copyright Briggs and Stratton. All Rights reserved Sep-2017

82 Wheel & Tire Group Note: Unless noted otherwise, use the standard torque specifications Mfg. No: Copyright Briggs and Stratton. All Rights reserved Sep-2017

83 Wheel & Tire Group REF NO PART NO QTY DESCRIPTION WHEEL, CASTER, 11 X SILVER BEAD LO X1 2 TIRE, FRONT, 11X (SV) X2 2 WHEEL ASSEMBLY, 11 X (SV) WASHER, 1/2 SAE X1 4 BEARING, CASTER WHEEL, 11 X (SV) BEARING, RETAINER -(SV) CASTER AXLE DDSH X56 2 BOLT, 1/2-13 X 7 GD5 YZ NUT, 1/2-13 HEX NYLOCK FLANGE NUT, 1/2-20, FOR WHEEL BOLT SILVER TIRE/WHEEL ASM, 22X11-10, TURF MASTER -(Models with 48" Decks Only) X1 1 WHEEL, 10 X 7 4/4, 0" OFFSET -(SV - Models with 48" Decks Only) X2 1 TIRE, 22 X , 4 PLY -(SV - Models with 48" Decks Only) TIRE ASM, 20X , 4 BOLT -(Models with 44" Decks Only) X1 1 WHEEL, 10 X 7, 4/4 BC, 1.12" POS OFFSET -(SV - Models with 44" Decks Only) X1 1 TIRE, 20 X NHS, 4 PR TURF MASTER -(SV - Models with 44" Decks Only) Copyright Briggs and Stratton. All Rights reserved Sep-2017