Haz. HazMax Intrepid/nm TECHNICAL SPECIFICATIONS

Transcription

1 Haz HazMax Intrepid/nm APPLICATIONS Hazardous locations Marine and watertight requirements Dusttight requirements Oil and gas exploration and production Petrochemical facilities APPROVALS Class I Division 2 - Groups A, B, C, & D Class I Zone 2 - Groups IIA, IIB & IIC Class II Division 2 - Groups F & G Class III, Type 4 Enclosure Type 4X Waste water treatment plants Food & beverage processing facilities IP66 Marine Outside Type Saltwater ABS NSF STANDARDS UL Hazardous Locations CSA - Class UL Emergency Lighting Equipment CSA - Class UL 1598A - Luminaires for Marine Vessels NSF/ANSI Splash Zone EN Ingress Protection Canadian Processed Products Regulations C.R.C. c291 TECHNICAL SPECIFICATIONS HOUSING.080 inch thick minimum, fiberglass reinforced polyester. LENS inch thick, matte polycarbonate. Optional clear polycarbonate. FEATURES Fluorescent system provides energy savings up to 50% when compared to HID. Third party certified for operation in high ambient temperatures, up to 65ºC (149ºF). Multi voltage electronic ballast resistant to brownouts or voltage and frequency fluctuations. Stainless steel latches, mounting feet and lens retainers. Impact resistant UV stabilized polycarbonate lens. Shoc Loc Bi-Pin spring loaded lamp holders for T5, T8 and T12 lamp types, provide superior resistance to shock and vibration. USDA compliant materials. Meets Canadian Processed Products Regulations C.R.C. c291. Neoprene gasket resists petroleum. Three lamp models are provided with (1) single-lamp ballast and (1) two-lamp ballast for independent switching. Optional self contained emergency battery backup ballasts. Optional certified test switch on emergency models. Optional long life T5 lamps available upon request (consult factory). REFLECTOR Type 5052H32 aluminum with an electrostatically applied white polyester powder coat finish. Minimum 90% reflectance. GASKET One piece neoprene. MOUNTING Stainless steel vibration dampening feet for ceiling, wall or chain mount. Optional pendant mount version. Kits available for uni-strut/rod and pole mount. LATCHES Stainless steel over the center cam. LAMP HOLDERS Spring loaded on one end for linear lamp types. ENTRIES Two 3 4 NPT hubs, one end plugged. LAMP TYPES See ORDERING REFERENCES. Lamps not provided. BALLAST 120 to 277 volt 50/60Hz electronic, optional 347v and 480v. EMERGENCY BATTERY BACKUP BALLAST Optional, self contained 90 minute minimum for all lamp types. 120 minutes minimum for F32T8 one lamp. Starting temperature 32ºF/0ºC. 244

2 ORDERING REFERENCES SPP ** 1. Series SPP 2. Length (nominal) 2-2 foot 4-4 foot 3. Number of Lamps 1-1 lamp 2-2 lamps 3-3 lamps, Lamp Types 1, 5 & lamps, 4 ft unit, Lamp Type 2 only 4. Lamp Types 1-17/32-2 ft F17 or 4 ft F32 - T8 Bi-Pin ft FT40 - CF 2G /54-2 ft F24 or 4 ft F54 - T5HO Mini Bi-Pin 6-14/28-2 ft F14 or 4 ft F28 - T5 Mini Bi-Pin ft F48 - T8HO RDC 8-35/60-2 ft F24 or 4 ft F48 - T12HO RDC 5. Voltage / Frequency to 277 Volt 50/60 Hz Volt 60 Hz, consult factory for availability Volt 60 Hz, consult factory for availability 6. Mounting Style 0 - Feed-through, two ¾ hubs 1 - Pendant Mount, two ¾ hubs (Not for marine applications and not available for 2 ft models) 7. Special Options EM1 - Emergency Battery Backup Ballast, 1 lamp, 277v max EMT1 - Emergency Battery Backup Ballast, 1 lamp, 277v max, test switch L* - Lamps LL* - Long Life Lamps (F54T5H0 only) XC - Clear Polycarbonate Lens S - Switch, on/off T - Multi Point Terminal Block P - Access Plate with 4 pole terminal block *Lamps are not included unless option L or LL is specified. Notes: 1. Consult factory for options not listed. COMMONLY ORDERED LUMINAIRES & CROSS REFERENCE Weight Part No. Description Legacy P/N Lbs Kg SPP22170 Fiberglass Reinforced Polyester 2 ft fixture 2 x F v 50/60 Hz FPS217D SPP42170 Fiberglass Reinforced Polyester 4 ft fixture 2 x F v 50/60 Hz FPS232D SPP42870 Fiberglass Reinforced Polyester 4 ft fixture 2 x F v 50/60 Hz FPS260D SPP43170 Fiberglass Reinforced Polyester 4 ft fixture 3 x F v 50/60 Hz FPS332D FX2175 Matte Polycarbonate Lens with Gasket 2 ft FX FX2177 Matte Polycarbonate Lens with Gasket 4 ft FX FX2163 Clear Polycarbonate Lens with Gasket 2 ft FX FX2165 Clear Polycarbonate Lens with Gasket 4 ft FX FX8014A Latches FX8014A.1.05 Non Metallic - Hazardous Area Lighting P A U L U H N H A Z M A X I N T R E P I D / N M 245

3 HazMax Intrepid/nm SPARE PARTS Part No. FX5307 FX5305 FX5174 FX5221 FX5349 FX5334 FX5334 FX5272 FX5307 FX5305 FX5340 FX5340 FX5349 FX5334 FX5334 FX5272 FX5128HDU FX5346HDU FX3573 FX3574 Description BALLAST V AC 50/60HZ, 1 x 14, F14T5 BALLAST V AC 50/60HZ, 1 x 28, F28T5 BALLAST V AC 50/60HZ, 1 x 24, F24T5HO BALLAST V AC 50/60HZ, 1 x 54, F54T5HO BALLAST V AC 50/60HZ, 1 x 17, F17T8 BALLAST V AC 50/60HZ, 1 x 32, F32T8 BALLAST V AC 50/60HZ, 1 x 44, F48T8HO BALLAST V AC 50/60HZ, 1 x 35, F24T12HO BALLAST V AC 50/60HZ, 1 x 60, F48T12HO BALLAST V AC 50/60HZ, 1 x 40 CF, FT40 2G11 BALLAST V AC 50/60HZ, 2 x 14, F14T5 BALLAST V AC 50/60HZ, 2 x 28, F28T5 BALLAST V AC 50/60HZ, 2 x 24, F24T5HO BALLAST V AC 50/60HZ, 2 X 54, F54T5HO BALLAST V AC 50/60HZ, 2 x 17, F17T8 BALLAST V AC 50/60HZ, 2 x 32, F32T8 BALLAST V AC 50/60HZ, 2 x 44, F48T8HO BALLAST V AC 50/60HZ, 2 x 35, F24T12HO BALLAST V AC 50/60HZ, 2 x 60, F48T12HO BALLAST V AC 50/60HZ, 2 x 40 CF, FT40 2G11 EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for CF, T8, T8HO & T12HO EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for T5, T5HO LAMP, 14w, F14T5 LAMP, 28w, F28T5 FX3568 LAMP, 24w, F24T5HO FX3567 LAMP, 54w, F54T5HO FX3577 LAMP, 54w, Long Life F54T5HO FX3528 LAMP, 17w, F17T8 FX3527 LAMP, 32w, F32T8 FX3565 LAMP, 44w, F48T8HO FX3507 LAMP, 35w, F24T12HO FX3505 LAMP, 60w, F48T12HO FX3533 LAMP, 40w, CF, FT40 2G11 FX8014A LATCH GKT LENS GASKET, 2 ft. models GKT LENS GASKET, 4 ft. models FX4008 LAMP HOLDER, 17w, 20w, 24w, 32w, 40w & 54w Stationary FX4009 LAMP HOLDER, 17w, 20w, 24w, 32w, 40w & 54w Spring FX4008SET LAMP HOLDER, (1 ea. FX4008, 4009) FX4004 LAMP HOLDER, 35w & 60w Stationary FX4005 LAMP HOLDER, 35w & 60w Spring FX4004SET LAMP HOLDER, (1ea. FX4004, 4005) FX4043 LAMP HOLDER, 40w CF FX2175 MATTE POLYCARBONATE LENS (with Gasket), 2ft. models FX2177 MATTE POLYCARBONATE LENS (with Gasket), 4ft. models FX2163 CLEAR POLYCARBONATE LENS (with Gasket), 2ft. models FX2165 CLEAR POLYCARBONATE LENS (with Gasket), 4ft. models CX1517 CABLE GLAND, 3 4 NPT non metallic TEMPERATURE CODES & APPROVALS Lamp Wattage Ballast/Socket Type ANSI Lamp Code Class I Class I Class II Class III Class II & III Starting T-Code Division 2 Division 2 T-Code Temp Maximum Ambient* 17 T8 Bi-Pin G13 F17-T8 T5 A,B,C & D T3C 0ºF/-18ºC 55ºC 90ºC 32 T8 Bi-Pin G13 F32-T8 T5 A,B,C & D T3C -20ºF / -29ºC 55ºC 90ºC 40 4 Pin 2G11 FT40-CF T4 A,B,C & D T3C 0ºF/-18ºC 40ºC 90ºC 24/54 T5HO Mini Bi-Pin G5 F24/F54-T5HO T4 A,B,C & D T3C -20ºF/-29ºC 55ºC 90ºC 14/28 T5 Mini Bi-Pin G5 F14/F28-T5 T4 A,B,C & D T3C 0ºF/-18ºC 55ºC 90ºC 44 T8HO RDC R17d F48-T8HO T4 A,B,C & D T3C -20ºF/-29ºC 40ºC 90ºC 35/60 T12HO RDC R17d F24/F48-T12HO T4 A,B,C & D T3C -20ºF/-29ºC 40ºC 90ºC *Consult factory for optional higher ambient models. Supply Wire 246

4 DIMENSIONS C Nominal Length Dimensions in Inches / Centimeters A B C Carton W x D X L Inches Lbs Nominal Weight 29.0 / / / x 6 1 x Foot / / / x 6 x Foot Kg MOUNTING OPTIONS MOUNTING KITS FPSPMKIT Pole Mount FPS-UNI-MNT Rod Mount FPSWMKIT Corner Wall Mount Kit Non Metallic - Hazardous Area Lighting P A U L U H N H A Z M A X I N T R E P I D / N M 247

5 Haz HazMax Versa/nm APPLICATIONS Mid & low bay Hazardous locations Wet environments Food & beverage processing facilities APPROVALS Class I Division 2 Groups A, B, C & D Class I Zone 2 Groups IIA, IIB & IIC Class II Division 2 Groups F & G Class III Petrochemical facilities Waste water treatment plants Storage areas Enclosed & Gasketed Type 3R NSF STANDARDS UL 844 Hazardous Locations CSA - Class UL Luminaires CSA - Class UL Emergency Lighting Equipment NSF/ANSI Splash Zone Canadian Processed Products Regulations C.R.C. c291 TECHNICAL SPECIFICATIONS HOUSING Fiberglass reinforced polyester. LENS Matte acrylic. Optional matte polycarbonate. REFLECTOR Steel with a white gloss finish. FEATURES Fluorescent system provides energy savings up to 50% when compared to HID. Third party certified for operation in high ambient temperatures, up to 65ºC (149ºF). Multi voltage electronic ballast resistant to brownouts or voltage and frequency fluctuations. Continuous form-in-place closed cell gasket and field replaceable lens. Feed-through design or optional pendant hub design. USDA compliant materials. Meets Canadian Processed Products Regulations C.R.C. c291. Full steel interior channel assembly reinforces hub entry and provides continuous ground. Optional self contained, emergency battery backup ballasts. Optional long life T5 lamps available upon request (consult factory). GASKET Permanently mounted closed cell neoprene. MOUNTING Various stainless steel mounting options. LATCHES Non-metallic. Optional stainless steel. LAMP HOLDERS Spring loaded on HO models. Industrial grade high temperature PBT locking sockets on RS models. ENTRIES Feed-through clearance holes with two 1 2 NPT hubs, one on each end. LAMP TYPES See ORDERING REFERENCES. Lamps not provided. BALLAST 120 to 277 volt 50/60Hz electronic. EMERGENCY BATTERY BACKUP BALLAST Optional, self contained 90 minute minimum for all lamp types. 120 minutes minimum for F32T8 one lamp. Starting temperature 32ºF/0ºC. 248

6 ORDERING REFERENCES VPH ** 1. Series VPH 2. Length (nominal) 2-2 foot 4-4 foot 8-8 foot 3. Number of Lamps 2 - For 2 lamps 4 - For 4 lamps (4 ft with four F17 or 8 ft with four F32, F54 or F48 Lamp Types) 4. Lamp Types 1-17/32-2 ft F17 or 4 ft F32 - T8 Bi-Pin ft FT40 - CF 2G /54-2 ft F24 or 4 ft F54 - T5HO Mini Bi-Pin 6-14/28-2 ft F14 or 4 ft F28 - T5 Mini Bi-Pin 7-44/86-4 ft F48 or 8 ft F96 - T8HO RDC 8-35/60/110-2 ft F24, 4 ft F48 or 8 ft F96 - T12HO RDC 5. Voltage / Frequency to 277 Volt 50/60 Hz Volt 60 Hz, consult factory for availability Volt 60 Hz, consult factory for availability 6. Mounting Style 0 - Feed-through with 2- ½ NPT hubs 1 - Feed-through with 2- ¾ NPT hubs 2 - Pendant with 2- ½ NPT hubs 3 - Pendant with 2- ¾ NPT hubs 7. Special Options EM1 - Emergency Battery Backup Ballast, 1 lamp, 277v max EMT1 - Emergency Battery Backup Ballast, 1 lamp, 277v max, test switch L* - Lamps LL* - Long Life Lamps (F54T5H0 only) P - Matte Polycarbonate Lens S - Switch, on/off SSC - Stainless Steel Latches TSSC - Tamper Proof Stainless Steel Latches * Lamps are not included unless option L or LL is specified. Notes: 1. Consult factory for options not listed. SPARE PARTS Part No. FX5307 FX5305 FX5340 FX5340 FX5349 FX5369 FX5334 FX5338 FX5338 FX5272 FX5128HDU FX5346HDU FX3573 FX3574 FX3568 FX3567 FX3577 FX3528 Description BALLAST V 60HZ, 2 x 14, F14T5 BALLAST V 60HZ, 2 x 28, F28T5 BALLAST V 60HZ, 2 x 24, F24T5HO BALLAST V 60HZ, 2 x 54, F54T5HO BALLAST V 60HZ, 2 x 17, F17T8 BALLAST V 60HZ, 2 x 32, F32T8 BALLAST V 60HZ, 2 x 44, F48T8HO BALLAST V 60HZ, 2 x 86, F96T8HO BALLAST V 60HZ, 2 x 35, F24T12HO BALLAST V 60HZ, 2 x 60, F48T12HO BALLAST V 60HZ, 2 x 110 F96T12HO BALLAST V 60HZ, 2 x 40 CF, FT40 2G11 EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for CF, T8, T8HO & T12HO EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for T5 & T5HO LAMP, 14w, F14T5 LAMP, 28w, F28T5 LAMP, 24w, F24T5HO LAMP, 54w, F54T5HO LAMP, 54w, Long Life F54T5HO LAMP, 17w, F17T8 FX3527 FX3565 FX3566 FX3507 FX3505 FX3523 FX3533 LAMP, 32w, F32T8 LAMP, 44w, F48T8HO LAMP, 86w, F96T8HO LAMP, 35w, F24T12HO LAMP, 60w, F48T12HO LAMP, 110w, F96T12HO LAMP, 40w CF, FT40 2G LENS, deep acrylic, 4 ft, HO model LENS, deep acrylic, 8 ft models LENS, shallow acrylic, 4 ft model, except HO LENS, shallow acrylic, 2 ft models LAMP HOLDER, RDC, fixed for HO models LAMP HOLDER, RDC, spring loaded for HO models LAMP HOLDER, Bi-Pin, T8 / T12 models LAMP HOLDER, 2G11 CF models LAMP HOLDER, T5 Fixed & Spring set LAMP SUPPORT, 2G11 CF models LAMP HOLDER, Single Pin, fixed LAMP HOLDER, Single Pin, spring loaded LENS LATCHES, non-metallic HUB, standard ½ NPT PLUG, standard ½ NPT Non Metallic - Professional Hazardous Area Use Lighting P A U L U H N H A Z M A X V E R S A / N M 249

7 HazMax Versa/nm TEMPERATURE CODES & APPROVALS Lamp Wattage Ballast/Socket Type ANSI Lamp Code Class I Class I Class II Class III Class II & III Starting T-Code Division 2 Division 2 T-Code Temp Maximum Ambient* 17 T8 Bi-Pin G13 F17-T8 T5 A,B,C & D T3C 0ºF / -18ºC 55ºC 90ºC 32 T8 Bi-Pin G13 F32-T8 T5 A,B,C & D T3C -20ºF / -29ºC 55ºC 90ºC 40 4 Pin 2G11 FT40-CF T5 A,B,C & D T3C 0ºF / -18ºC 40ºC 90ºC 24/54 T5HO Mini Bi-Pin G5 F24/F54-T5HO T5 A,B,C & D T3C -20ºF / -29ºC 55ºC 90ºC 14/28 T5 Mini Bi-Pin G5 F14/F28-T5 T5 A,B,C & D T3C 0ºF / -18ºC 55ºC 90ºC 44/86 T8HO RDC R17d F48/F96-T8HO T4A A,B,C & D T3C -20ºF / -29ºC 40ºC 90ºC 35/60/ 110 T12HO RDC R17d F24/F48/F96- T12HO *Consult factory for optional higher ambient models. Supply Wire T4A A,B,C & D T3C -20ºF / -29ºC 40ºC 90ºC DIMENSIONS Nominal Length Dimensions in Inches / Centimeters A B C Carton L x W x D Inches Lbs Nominal Weight 25.8 / / / x 6 1 x Foot Models / / / x 6 x Foot T5 & T8 Models / / / x 6 x Foot HO Models Foot Models / / / x 8 x kg 250

8 MOUNTING OPTIONS VP1091MTK Fixed ceiling / wall mounting kit. 2 stainless steel brackets & hardware to mount brackets to fixture. VP1093MTK Fixed corner mounting kit. 2 stainless steel brackets & hardware to mount brackets to fixture. HP1095MTK Pendant mounting kit. 1 saddle strap and 1 universal junction box & pendant cover (¾ NPT). Non Metallic - Hazardous Area Lighting P A U L U H N H A Z M A X V E R S A / N M 251

9 Haz HazMax Resista/nm APPLICATIONS High, mid & low bay Waste water treatment plants Hazardous locations Pulp & paper production High pressure hose down areas Food & beverage processing facilities Grain & sugar milling, processing & storage APPROVALS Class I Division 2 Groups A, B, C, & D Type 4 Class I Zone 2 Groups IIA, IIB & IIC Conforms to IP66 Class II Division 2 Groups F & G NSF Class III Enclosed & Gasketed STANDARDS UL Hazardous Locations c291 UL Emergency Lighting Equipment CSA - Class UL Luminaires CSA - Class CSA - Class NSF/ANSI Food Contact (WPS version) CSA - Class NSF/ANSI Splash Zone Canadian Processed Products Regulations C.R.C. TECHNICAL SPECIFICATIONS HOUSING/LENS End caps polybutylene terephthalate (PBT) or stainless steel, optional polycarbonate center stud. Clear, impact resistant, acrylic lens. FEATURES High output luminaire, up to 30,000 raw lumens. Fluorescent system provides energy savings up to 50% when compared to HID. Third party certified for operation in high ambient temperatures, up to 55ºC (131ºF). Multi voltage electronic ballast resistant to brownouts or voltage and frequency fluctuations. Hose tested at 1500 PSI for 60 minute duration, at 5 feet and 10 feet distance, nozzle dispersion 0 degree. USDA compliant materials. Meets Canadian Processed Products Regulations C.R.C. c291. Polybutylene Terephthalate (PBT) end cap provides the broadest range of chemical resistance. Field replaceable silicone gasket adhered in end cap. Options include: Stainless steel end caps, quick disconnect receptacle, stainless steel quick disconnect straps and center stud mount end caps. Optional self contained emergency battery backup ballasts. Emergency models feature EM markings or red end caps (center stud models only). Optional long life T5 lamps available upon request (consult factory). HARDWARE External hardware stainless steel. REFLECTOR Extruded aluminum assembly, coated gloss white. GASKETS One piece silicone. MOUNTING Cable, fixed, nylon coated suspended cable, wall mount, or stainless steel straps. Other options available see MOUNTINGS OPTIONS. LAMP HOLDERS Locking sockets on Bi-Pin models made of industrial grade high temperature PBT. Spring loaded polycarbonate sockets on all HO models. ENTRIES Single or feed-through 1 2 NPT. LAMP TYPES See ORDERING REFERENCES. Lamps not provided. BALLAST 120 to 277 volt 50/60Hz electronic. EMERGENCY BATTERY BACKUP BALLAST Optional, self contained 90 minute minimum for all lamp types. 120 minutes minimum for F32T8 one lamp. Starting temperature 32ºF/0ºC. 252

10 ORDERING REFERENCES WPH ** 1. Series WPH - Hazardous Area WPSH - Hazardous Area, SS end caps 2. Length (nominal) 2-2 foot 4-4 foot 8-8 foot 3. Number of Lamps 2-2 lamps 3-3 lamps (Lamp Types 1, 5 & 6) 4-4 lamps (4 ft fixture, Lamp Types 5 & 6 only. 8 ft fixtures with four 4 ft lamps, Lamp Types 1, 5, 6 & 8) 6-6 lamps (8 ft fixture with six 4 ft lamps, Lamp Types 1, 5 & 6) 4. Lamp Types 1-17/32/59-2 ft F17, 4 ft F32 - T8 Bi-Pin, 8 ft F96 Single Pin 3-60ES/75-8 ft F96 - T12 Single Pin 5-24/54-2 ft F24 or 4 ft F54 - T5HO Mini Bi-Pin 6-14/28-2 ft F14 or 4 ft F28 - T5 Mini Bi-Pin 7-44/86-4 ft F48 or 8 ft F96 - T8HO RDC 8-35/60/110-2 ft F24, 4 ft F48 or 8 ft F96 - T12HO RDC 6. Mounting / Entries 0 - Standard End Cap, with 1 strain relief connector 1 - Standard End Cap, feed-thru with 2 strain reliefs 2 - Center Stud End Cap, with 1 strain relief connector, with hanger brackets 3 - Center Stud End Cap, feed-thru with 2 strain reliefs, with hanger brackets 4 - Same as #2, with wall mount brackets 5 - Same as #3, with wall mount brackets 6 - Same as #2, with WP1050MTK straps 7 - Same as #3, with WP1050MTK straps 8 - Same as #0, with WP1050MTK straps 9 - Same as #1, with WP1050TMK straps 7. Special Options EM1 - Emergency Battery Backup Ballast, 1 lamp, 277v max EMT1 - Emergency Battery Backup Ballast, 1 lamp, 277v max, test switch L* - Lamps LL* - Long Life Lamps (F54T5HO only) S W3 - Switch, on/off - 3 ft 16/3 Cord, change suffix 3 for longer cord (WP163SR-3) (Not available for WPSH models) *Lamps are not included unless option L or LL is specified. 5. Voltage / Frequency to 277 Volt 50/60 Hz Volt 60 Hz, consult factory for availability Volt 60 Hz, consult factory for availability SPARE PARTS Part No. FX5307 FX5305 FX5340 FX5340 FX5322 FX5349 FX5369 FX5062 FX5062 FX5334 FX5338 Description BALLAST V 60Hz, 2 x 14, F14T5 BALLAST V 60Hz, 2 x 28, F28T5 BALLAST V 60Hz, 2 x 24, F24T5HO BALLAST V 60Hz, 2 x 54, F54T5HO BALLAST V 60Hz, 2 x 17, F17T8 BALLAST V 60Hz, 2 x 32, F32T8 BALLAST V 60Hz, 2 x 59, F96T8 BALLAST V 60Hz, 2 x 44, F48T8HO BALLAST V 60Hz, 2 x 86, F96T8HO BALLAST V 60Hz, 2 x 60ES, F96T12ES BALLAST V 60Hz, 2 x 75, F96T12 BALLAST V 60Hz, 2 x 35, F24T12HO BALLAST V 60Hz, 2 x 60, F48T12HO FX5338 BALLAST V 60Hz, 2 x 110, F96T12HO FX5128HDU EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for T8, T8HO, T12 & T12HO FX5346HDU EMERGENCY BATTERY BACKUP BALLAST, EM1/EMT1, V for T5 & T5HO FX3573 LAMP, 14w, F14T5 FX3568 FX3574 FX3567 FX3528 FX3527 FX3572 FX3565 FX3566 FX3523 FX3576 FX3507 FX3505 FX3550 LAMP, 24w, F24T5HO LAMP, 28w, F28T5 LAMP, 54w, F54T5HO LAMP, 17w, F17T8 LAMP, 32w, F32T8 LAMP, 59w, F96T8 LAMP, 44w, F48T8HO LAMP, 86w, F96T8HO LAMP, 75w, F96T12 LAMP, 60w ES, F96T12ES LAMP, 35w, F24T12HO LAMP, 60w, F48T12HO LAMP, 110w, F96T12HO LAMP HOLDER, RDC, spring loaded, HO models LAMP HOLDER, RDC, fixed, HO models LAMP HOLDER, Bi-Pin, T8/T12 models LAMP HOLDER, fixed, T LAMP HOLDER, Single Pin, fixed LAMP HOLDER, Single Pin, spring loaded NUT, stainless steel closed end Notes: 1. See ACCESSORIES for other items & mounts. 2. Consult factory for options not listed above GASKET, O-ring for stud STUD, SS, secures end cap to inner channel GASKET, for cord connector or optional receptacle CONNECTOR, cord strain relief, 1 2 NPT non-metallic TUBE, acrylic, 4 ft. models TUBE, acrylic, 8 ft. models TUBE, acrylic, 2 ft. models END CAP, electrical end ( 1 2 NPT hub) END CAP, non-electrical end FX6091EN FX6091BN END CAP, center stud, electrical end ( 1 2 NPT hub) END CAP, center stud, non-electrical end FX6841 WPSET END CAPS, stainless steel FX6841 FFSET END CAPS, center stud, stainless steel, FX6091 SETEM END CAPS, center stud red, EM models GASKET, O-ring for either end cap Non Metallic - Hazardous Area Lighting 253

11 HazMax Resista/nm TEMPERATURE CODES & APPROVALS Lamp Wattage Ballast/Socket Type ANSI Lamp Code Class I T Code Class I Division 2 Class II Division 2 Class III Class II & III T Code Starting Temp Max Ambient 17 T8 Bi-Pin G13 F17-T8 T5 A,B,C & D T3C 0ºF/-18ºC 55ºC 90ºC 32 T8 Bi-Pin G13 F32-T8 T5 A,B,C & D T3C -20ºF/-29ºC 55ºC 90ºC 24/54 T5HO Mini Bi-Pin G5 F24/F54 T5HO T5 A,B,C & D No No NA -20ºF/-29ºC 40ºC 90ºC 14/28 T5 Mini Bi-Pin G5 F14/F28 T5 T5 A,B,C & D No No NA 0ºF/-18ºC 40ºC 90ºC 44/86 T8HO RDC R17d F48/F96 T8HO T4A A,B,C & D T3C -20ºF/-29ºC 40ºC 90ºC 35/60/110 T12HO RDC R17d F24/F48/F96 T12HO T4A A,B,C & D T3C -20ºF/-29ºC 40ºC 90ºC *Consult factory for optional higher ambient models. Supply Wire DIMENSIONS Nominal Length Dimensions in Inches / Centimeters Carton W x D x L inches Nominal Weight A B C Lbs Kg 2 Foot 25.0 / / / x 6 1 x Foot 49.0 / / / x 8 x Foot 97.0 / / / x 8 x ACCESSORIES WP163SR-6 Cord assembly - strain relief connector and 6 feet of #16/3 cable. If longer cable required change suffix 6 to length needed. FX Wall Mount Bracket For Center Stud end caps. WP1050MTK 2 Quick Release Stainless steel straps. Included with MOUNTINGS 6, 7, 8 &

12 MOUNTING OPTIONS WP1012MTK Suspended cable kit nylon coated stainless steel cables with crimped on loops & 2 - S hooks. If longer cable required change 12 in part number to required length. Hanger Bracket CENTER STUD END CAP Center Stud end caps include hanger bracket and and stainless steel chain mount. MOUNTINGS 2 & 3. Non Metallic - Hazardous Area Lighting P A U L U H N H A Z M A X R E S I S T A / N M 255

13 Haz HazGuard Exacta/nm APPLICATIONS Ceiling, pendant and wall mount types Hazardous locations Marine and watertight requirements Dusttight requirements Grain & sugar milling, processing & storage Petrochemical facilities Coal processing & storage APPROVALS Class I Division 2 Groups A, B, C & D Class I Zone 2 Groups IIA, IIB & IIC Class II Division 2 Groups F & G Class III Type 4 Conforms to IP66 NSF Surface mining Pharmaceutical & additives formulation & processing Food and beverage processing facilities Pulp & paper production Waste water treatment plants Pipeline compressor/pumping & storage STANDARDS UL Hazardous Locations UL Luminaires CSA - Class CSA - Class NSF/ANSI Splash Zone Canadian Processed Products Regulations C.R.C. c291 TECHNICAL SPECIFICATIONS FEATURES Available in 150w incandescent or 18w, 26w and 32w compact fluorescent. Approved for use in Class II dust areas. High temperature silicone gasket provides a watertight seal. Watertight mounting in any direction. USDA compliant materials. Meets Canadian Processed Products Regulations C.R.C. c291. Optional polymeric or stainless steel guards. A wide variety of globe materials and colors. HOUSING & GLOBE BASE Reinforced polyethylene terephthalate (PET). GUARD Nylon 6/6 or stainless steel wire. HARDWARE Stainless steel. ENTRIES Four 3 4 NPT knockouts on ceiling and wall versions. One 3 4 NPT outlet on pendant version. GASKET One piece silicone. MOUNTING Ceiling, pendant or wall. LAMP HOLDER Incandescent, medium base porcelain. Compact fluorescent, polycarbonate. GLOBE Glass, tempered glass or polycarbonate. LAMP TYPES Incandescent or 4-pin compact fluorescent. Lamps not provided. VOLTAGE Incandescent 240v maximum. Compact fluorescent 120v or 277v. TEMPERATURE CODE At 40ºC ambient. Supply wire 90ºC. 256 Lamp Wattage Globe T-Code Incandescent 150 Glass T3 Incandescent 100 Glass T3C Incandescent 100 Polycarbonate T3C Compact fluorescent 32 Max All T3C

14 ORDERING REFERENCES IPEH 15I 1 GC GP C ** 1. Series IPEH 2. Lamp Types 15I watt max incandescent 18F - 18 watt compact fluorescent 26F - 26 watt compact fluorescent 32F - 32 watt compact fluorescent 3. Voltage / Frequency 1-120v 60 Hz 2-240v 50/60 Hz (incandescent only) 3-277v 60 Hz (compact fluorescent only) 4. Globe Type GC* - Glass, clear PC* - Polycarbonate, clear PP - Polycarbonate, prismatic TG - Tempered Glass, clear * For colored globes replace C with first letter of color required. (ie,: GR for red glass globe.) Colors available: amber, blue, green, red and white. Globe use - mounting warning: Glass globes 150 watt max, any mounting position. Polycarbonate globe 100 watt max, base up only. Polycarbonate globe 60 watt max, any mounting position. 5. Guard GP - Guard, polymeric (for glass globes only) GW - Guard, stainless steel wire 6. Mounting Options C - Ceiling Mount, four ¾" NPT hubs P - Pendant Mount, ¾ NPT hub W - Wall Mount & Outlet Box, four ¾" NPT hubs 7. Special Options L* - Lamp, installed *Lamps not included unless L option is selected. Notes 1. Consult factory for options not listed. COMMONLY ORDERED LUMINAIRES Part No. Mounting Lamp Type Shipping Weight Lamp Wattage Lbs Kg Shipping Volume IPE H15I 1GC GP P PENDANT Incandescent ft 3 IPE H18F 1GC GP P PENDANT Compact Fluorescent ft 3 IPE H26F 1GC GP P PENDANT Compact Fluorescent ft 3 IPE H32F 1GC GP P PENDANT Compact Fluorescent ft 3 IPE H15I 1GC GP C CEILING Incandescent ft 3 IPE H18F 1GC GP C CEILING Compact Fluorescent ft 3 IPE H26F 1GC GP C CEILING Compact Fluorescent ft 3 IPE H32F 1GC GP C CEILING Compact Fluorescent ft 3 IPE H15I 1GC GP W WALL Incandescent ft 3 IPE H18F 1GC GP W WALL Compact Fluorescent ft 3 IPE H26F 1GC GP W WALL Compact Fluorescent ft 3 IPE H32F 1GC GP W WALL Compact Fluorescent ft 3 Non Metallic - Hazardous Area Lighting P A U L U H N H A Z G U A R D E X A C T A / N M 257

15 HazGuard Exacta/nm DIMENSIONS Incandescent Compact Fluorescent Incandescent Compact Fluorescent Incandescent Compact Fluorescent Pendant Mount Ceiling Mount Wall Mount Mount Pendant Mount Ceiling Mount Wall Mount Type Incandescent Compact Fluorescent Incandescent Compact Fluorescent Incandescent Compact Fluorescent A (26.0) (30.5) (25.4) (29.8) (28.6) (33.0) B 9.50 (24.1) (28.6) 9.25 (23.5) (27.9) 10.5 (26.7) (31.1) C 4.50 (11.4) 4.50 (11.4) 4.62 (11.7) 4.62 (11.7) 7.50 (19.1) 7.50 (19.1) D (9.5) 3.75 (9.5)) (13.0) (13.0) Dimensions are in inches (cm). SPARE PARTS Part No. Description FX4030 FX4034 FX4034 INX INX2007CLR INX2007RED INX2007GRN INX2007BLU INX2007YEL INX2007HR P100C FX5206 LAMP HOLDER, 18w CF LAMP HOLDER, 26w CF LAMP HOLDER, 32w CF LAMP HOLDER, Incandescent GLASS GLOBE, Clear GLASS GLOBE, Red GLASS GLOBE, Green GLASS GLOBE, Blue GLASS GLOBE, Amber GLASS GLOBE, Tempered Glass (HR) GLOBE, Clear Polycarbonate BALLAST, 120v, 18w CF FX5206 FX5206 FX3552 FX3553 FX3554 INX3558 INXGP150 INXGW150 GKT BALLAST, 120v, 26w CF BALLAST, 120v, 32w CF LAMP, 18w CF LAMP, 26w CF LAMP, 32w CF LAMP, 150w Incandescent GUARD, Polymeric GUARD, Stainless steel GASKET, Junction Box 258