SERVICE BULLETIN CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION

Transcription

1 TITLE CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION EFFECTIVITY MODEL UNIT NUMBERS NOTE: This Service Bulletin may only be accomplished at a Cessna-owned or an authorized Citation Service Center. REASON To comply with foreign certification requirements. DESCRIPTION This service bulletin provides parts and instructions to install Czechoslovakian placards. COMPLIANCE OPTIONAL. This service bulletin may be accomplished at the discretion of the owner. A service bulletin published by Cessna Aircraft Company may be recorded as completed in an aircraft log only when the following requirements are satisfied: 1) The mechanic must complete all of the instructions in the service bulletin, including the intent therein. 2) The mechanic must correctly use and install all applicable parts supplied with the service bulletin kit. Only with written authorization from Cessna Aircraft Company can substitute parts or rebuilt parts be used to replace new parts. 3) The mechanic or airplane owner must use the technical data in the service bulletin only as approved and published. 4) The mechanic or airplane owner must apply the information in the service bulletin only to aircraft serial numbers identified in the Effectivity section of the bulletin. 5) The mechanic or airplane owner must use maintenance practices that are identified as acceptable standard practices in the aviation industry and governmental regulations. No individual or corporate organization other than Cessna Aircraft Company is authorized to make or apply any changes to a Cessna-issued service bulletin, service letter, or flight manual supplement without prior written consent from Cessna Aircraft Company. Cessna Aircraft Company is not responsible for the quality of maintenance performed to comply with this document, unless the maintenance is accomplished at a Cessna-owned Citation Service Center. FLIGHT CREW OPERATIONS No Change. Page 1 of 4 Cessna Aircraft Company, Citation Marketing Division, P.O. Box 7706, Wichita, KS 67277, U.S.A , Fax COPYRIGHT 2004

2 APPROVAL FAA approval has been obtained on technical data in this publication that affects airplane type design. This information shall be considered an amendment to the Cessna Manufacturer s Maintenance Manual. MANPOWER MATERIAL - Cost and Availability WORK PHASE MAN-HOURS Modification * PART NUMBER AVAILABILITY COST * * * Refer to the attached Service Bulletin Supplemental Data sheet for man-hours, material cost and availability, and warranty information. CONSUMABLE MATERIAL In addition to the above kit(s), the following materials, or equivalent, are required for the accomplishment of this service bulletin. NAME NUMBER MANUFACTURER USE Clear Polyurethane Top Coat Sherwin Williams 630 East 13th Street Andover, KS To edge seal the exterior placards. CHANGE IN WEIGHT AND BALANCE Negligible REFERENCES The engineering drawing that follows must obtained to complete this service bulletin. The latest revision and all applicable DCN s for each document must be used. DOCUMENT NUMBER TITLE Informational Markings Instl. - Czech Rep PUBLICATIONS AFFECTED Cessna Model 550 Citation Bravo Illustrated Parts Catalog ACCOMPLISHMENT INSTRUCTIONS 1. Prepare the airplane for maintenance. A. Make sure that all switches are in the OFF/NORM position. B. Disconnect electrical power from the airplane. (1) Disconnect the airplane battery. (2) Disconnect external electrical power. C. Attach maintenance warning tags to the battery and external power receptacle that have "DO NOT CONNECT ELECTRICAL POWER - MAINTENANCE IN PROGRESS" written on them. Page 2

3 2. Remove the placards, decals and photos as necessary. 3. Install the placards, decals and photos. (Refer to Cessna Engineering Drawing ) 4. Edge seal the exterior placards as necessary with clear polyurethane top coat. 5. Remove the warning tags and connect the battery. 6. Record that this service bulletin has been completed. A. Complete a Maintenance Transaction Report. B. Put a copy of the completed Maintenance Transaction Report in the airplane logbook. C. Send a copy of the completed Maintenance Transaction Report to: CESCOM, PO Box 7706, Wichita, KS MATERIAL INFORMATION NOTE: The parts included in this service bulletin cover installation for one airplane. NEW P/N QUAN- TITY KEY WORD OLD P/N INSTRUCTIONS/ DISPOSITION 1 Kit, consisting of the following parts: MS21069L04 3 Nutplate MS24693S26 5 Screw MS24693S27 6 Screw MS27130-S1K 12 Nut MS27130-S1K Discard MS Screw MS Discard NAS1832A Insert S1021A4-4 4 Screw S1022A4 Discard Plate Assembly Photo - Max Baggage Discard Decal - Cabin Door Discard Decal - Cabin Door Discard Decal - Cabin Door Discard Photo - Tail Max Discard Photo - Tail Max Discard Photo - Tail Max Discard Photo - Ski Tube Discard Decal - Emergency Exit Discard Decal - Emergency Exit Discard Placard - Curtain Discard Placard - Cabinet Instructions Discard Page 3

4 NEW P/N QUAN- TITY KEY WORD OLD P/N INSTRUCTIONS/ DISPOSITION Photo - Door Catch Discard Decal - Cabin Door Discard Decal - Cabin Door Placard - Exit Decal - Escape Hatch Discard Decal - Escape Hatch Discard Placard - Coat Rod Discard Placard - Aft Compartment Discard Mounting Plate Mounting Plate Mounting Plate Placard - Seat Instructions Install over the Placard - Seat Instructions Install over the Placard - Trash Container Install over the Placard - Seat Position Install over the Placard - Life Vest Install over the Placard - Executive Table Install over the Placard - Sliding Door Install over the Placard - Life Vest Only Install over the Placard - No Smoking in Lavatory 1 Instructions Install over the Page 4

5 TITLE SUPPLEMENTAL DATA CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION EFFECTIVITY MODEL UNIT NUMBERS MANPOWER WORK PHASE Modification MAN-HOURS As Required MATERIAL - Cost and Availability PART NUMBER AVAILABILITY COST * * * Please contact Citation Parts Distribution for current cost and availability of parts listed in this service bulletin. Phone at (Domestic) or (International). Send to: citationparts@cessna.textron.com or telefax at Based on availability and lead times, parts may require advanced scheduling. In cases where the required part(s) are available as exchange, order the exchange part and, upon completion, expedite the return of the removed core to avoid return penalties. Contact the Citation Parts Distribution Sales Desk for availability of exchange parts. Page 1 of 1 Cessna Aircraft Company, Citation Marketing Division, P.O. Box 7706, Wichita, KS 67277, U.S.A , Fax COPYRIGHT 2004

6