SERVICE BULLETIN REVISION

Transcription

1 Revision 1 REVISION TRANSMITTAL SHEET This sheet transmits Revision 1 to, which: A. Adds a Note to the EFFECTIVITY section and Step 1 to the ACCOMPLISHMENT INSTRUCTIONS section to include a reference to SB Lights - Bonding Improvement For The Over Wing Emergency Light. NOTE: This revision replaces the original issue of in its entirety. NOTE: Change bars and pointing hands are not used in this publication to denote revised material. This transmittal sheet provides a complete description of the changes made by this revision, except for editorial changes. REVISION COMPLIANCE NO EFFECT. Airplanes previously modified by this service bulletin are not affected by this revision. SUMMARY OF REVISIONS Original Issue Feb, 20/2007 Revision 1 Mar 25/2008

2

3 TITLE LIGHTS - LIGHT EMITTING DIODE (LED) EMERGENCY OVER WING LIGHT INSTALLATION EFFECTIVITY MODEL SERIAL NUMBERS 750 (Citation X) thru The equivalent of this service bulletin has been incorporated on production airplanes and On. NOTE: Airplanes must have SB Lights - Bonding Improvement For The Over Wing Emergency Light installed before or at the same time as this service bulletin. REASON Provides a LED-style replacement light for the emergency over wing light mounted in the right fuselage fairing panel. DESCRIPTION This service bulletin provides the parts and instructions necessary to replace the incandescent emergency over wing light with a LED light assembly. COMPLIANCE OPTIONAL. This service bulletin can be accomplished at the discretion of the owner. A service bulletin published by Cessna Aircraft Company may be recorded as completed in an aircraft log only when the following requirements are satisfied: 1) The mechanic must complete all of the instructions in the service bulletin, including the intent therein. 2) The mechanic must correctly use and install all applicable parts supplied with the service bulletin kit. Only with written authorization from Cessna Aircraft Company can substitute parts or rebuilt parts be used to replace new parts. 3) The mechanic or airplane owner must use the technical data in the service bulletin only as approved and published. 4) The mechanic or airplane owner must apply the information in the service bulletin only to aircraft serial numbers identified in the Effectivity section of the bulletin. 5) The mechanic or airplane owner must use maintenance practices that are identified as acceptable standard practices in the aviation industry and governmental regulations. No individual or corporate organization other than Cessna Aircraft Company is authorized to make or apply any changes to a Cessna-issued service bulletin, service letter, or flight manual supplement without prior written consent from Cessna Aircraft Company. Cessna Aircraft Company is not responsible for the quality of maintenance performed to comply with this document, unless the maintenance is accomplished at a Cessna-owned Citation Service Center. Revision 1 - Mar 25/2008 Page1of8 Cessna Aircraft Company, Citation Marketing Division, P.O. Box 7706, Wichita, KS 67277, U.S.A , Fax COPYRIGHT 2007

4 FLIGHT CREW OPERATIONS No Changes APPROVAL Cessna received FAA approval for the technical data in this publication that changes the airplane type design. This information is an amendment to the applicable maintenance manual. MANPOWER MATERIAL - Cost and Availability WORK PHASE MAN-HOURS Modification * PART NUMBER AVAILABILITY COST -0 * * -1 * * * Refer to the Manpower, Material - Cost and Availability, and Warranty sections in the attached Service Bulletin Supplemental Data sheet. CHANGE IN WEIGHT AND BALANCE Negligible REFERENCES Cessna Model 750 Maintenance Manual PUBLICATIONS AFFECTED Cessna Model 750 Illustrated Parts Catalog Cessna Model 750 Wiring Diagram Manual ACCOMPLISHMENT INSTRUCTIONS 1. Install SB Lights - Bonding Improvement For The Over Wing Emergency Light. NOTE: Airplanes must have SB Lights - Bonding Improvement For The Over Wing Emergency Light installed before or at the same time as this service bulletin. 2. Prepare the airplane for maintenance: A. Make sure that all switches are in the OFF/NORM position. B. Disconnect electrical power from the airplane. (1) Disconnect the airplane batteries. (2) Disconnect external electrical power. C. Attach maintenance warning tags to the batteries and external power receptacle that have "DO NOT CONNECT ELECTRICAL POWER - MAINTENANCE IN PROGRESS" on them. 3. Remove the right fuselage fairing panel 174AT. (Refer to the Model 750 Maintenance Manual, Chapter 6, Access Plates and Panels Identification - Description and Operation.) Revision 1 - Mar 25/2008 Page 2

5 4. (Refer to Figure 1.) Remove the X Light Assembly: A. Remove and discard four MS24693C28 Screws from the X Light Assembly. B. Disconnect the electrical connector. C. Remove and discard the X Light Assembly. 5. (Refer to Figure 2.) Do the wire modifications as follows: A. (Airplanes thru ) Cut the terminals from the wires marked 1FR006-DPR060 and 2FR006-57PR006. (1) Install the two S ID Sleeves marked 2JR100 - DPR060 on the wire marked 1FR006-DPR060. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Wiring - Maintenance Practices.) (2) Install the two S ID Sleeves marked 1JR100-57PR006 on the wire marked 2FR006-57PR006. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Wiring - Maintenance Practices.) (3) Install the two S Sockets on the ends of the wires. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Electrical Connectors - Maintenance Practices.) (4) Install the S Housing. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Electrical Connectors - Maintenance Practices.) B. (Airplanes thru ) Cut the terminals from the wires marked 1FR006-DPR060, 2FR006-WHTDR005 and 2FR006-WHTDR006. (1) Install the two S ID Sleeves marked 2JR100 - DPR060 on the wire marked 1FR006-DPR060. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Wiring - Maintenance Practices.) (2) Install the two S ID Sleeves marked 1JR100-WHTDR005 on the wire marked 2FR006-WHTDR005. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Wiring - Maintenance Practices.) (3) Install the two S ID Sleeves marked 1JR100-WHTDR006 on the wire marked 2FR006-WHTDR006. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Wiring - Maintenance Practices.) (4) Install the M81824/1-1 Splice on the ends of the wires marked 1JR100-WHTDR005 and 1JR100-WHTDR006. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Splices and Terminals - Maintenance Practices.) (5) Install the 3 Inch M81044/ Wire (Unmarked) into the M81824/1-1 Splice. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Splices and Terminals - Maintenance Practices.) (6) Install the two S Sockets on the ends of the wires. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Electrical Connectors - Maintenance Practices.) (7) Install the S Housing. (Refer to the Model 750 Wiring Diagram Manual, Chapter 20, Electrical Connectors - Maintenance Practices.) Revision 1 - Mar 25/2008 Page 3

6 6. (Refer to Figure 1.) Install the OWL LED Light Assembly: NOTE: The exposed surface of the OWL LED Light Assembly may be painted or polished at the discretion of the airplane owner. The light assembly should be painted or polished before the assembly is installed. A. Install the OWL LED Light Assembly in the access panel with four MS24693S27 Screws. NOTE: The OWL LED Light Assembly must be installed with the vent hole in the down position. NOTE: The OWL LED Light Assembly must be installed with the wiring going aft. B. Connect the electrical connector. C. Use the S Tie Straps to secure any excess wire length. 7. Install the right fuselage fairing panel 174AT. (Refer to the Model 750 Maintenance Manual, Chapter 6, Access Plates and Panels Identification - Description and Operation.) 8. Do a test of the emergency exit light: A. Remove the warning tags and connect battery power to the airplane. B. Move the EMER LTS switch to the ON position. C. Make sure that emergency over wing light is on. D. Move the EMER LTS switch to the OFF position. E. Remove battery power from the airplane. 9. Record that this service bulletin has been completed: A. Complete a Maintenance Transaction Report. B. Put a copy of the completed Maintenance Transaction Report in the airplane logbook. C. Send a copy of the completed Maintenance Transaction Report to: CESCOM, P.O. Box 7706, Wichita, KS Revision 1 - Mar 25/2008 Page 4

7 MATERIAL INFORMATION (Airplanes serial numbers thru ) Order the kit below to install this modification. NEW P/N QUAN- TITY KEY WORD OLD P/N INSTRUCTIONS/ DISPOSITION -0 1 Kit, consisting of the following parts: MS24693S27 4 Screw MS24693C28 Discard OWL LED Light Assembly X Discard S Socket None S Housing None S Tie Strap None S ID Sleeve Marked 2JR100 - DPR060 S ID Sleeve Marked 1JR100-57PR006 1 Instructions None None (Airplanes serial numbers thru ) Order the kit below to install this modification. NEW P/N QUAN- TITY KEY WORD OLD P/N INSTRUCTIONS/ DISPOSITION -1 1 Kit, consisting of the following parts: MS24693S27 4 Screw MS24693C28 Discard M81044/ Inches Electrical Wire (Not Marked) None M81824/1-1 1 Splice None OWL LED Light Assembly X Discard S Socket None S Housing None S Tie Strap None S ID Sleeve Marked 2JR100 - DPR060 S ID Sleeve Marked 1JR100-WHTDR006 S ID Sleeve Marked 1JR100-WHTDR005 1 Instructions None None None Revision 1 - Mar 25/2008 Page 5

8 Figure 1. LED Light Installation (Sheet 1) Revision 1 - Mar 25/2008 Page 6

9 Figure 2. Wire Modification (Sheet 1) Revision 1 - Mar 25/2008 Page 7

10 Figure 2. Wire Modification (Sheet 2) Revision 1 - Mar 25/2008 Page 8

11 TITLE SUPPLEMENTAL DATA LIGHTS - LIGHT EMITTING DIODE (LED) EMERGENCY OVER WING LIGHT INSTALLATION EFFECTIVITY MODEL SERIAL NUMBERS 750 (Citation X) thru The equivalent of this service bulletin has been incorporated on production airplanes and On. MANPOWER WORK PHASE Modification MAN-HOURS As Required MATERIAL - Cost and Availability PART NUMBER AVAILABILITY COST -0 * * -1 * * * Please contact Citation Parts Distribution for current cost and availability of parts listed in this service bulletin. Phone at (Domestic) or (International). Send to: citationparts@cessna.textron.com or telefax at Based on availability and lead times, parts may require advanced scheduling. Revision A - Mar 25/2008 Page1of1 Cessna Aircraft Company, Citation Marketing Division, P.O. Box 7706, Wichita, KS 67277, U.S.A , Fax COPYRIGHT 2007

12