Elevation Resources LLC

Transcription

1 FIELD: Emma COUNTY/STATE Andrews/Texas PMD: 16,600 PVD: 11,075 LOCATION: ELEVATION (RKB): 3,158 API #: SERIAL NO: SPUD DATE: Sep OBJECTIVE: Drill 5300' lateral JOB NAME: University 1-20 #4H Elevation Resources LLC DAILY OPERATIONS CONTRACTOR/RIG#: Independent Contract Drilling/ICD 208 Nov MD: 16,467 TVD: 10,995 FOOTAGE: MW: 0.0 LB PTD: 16,600 RIG SUPERVISOR: David Crow PBTD: NU & TEST TBG HEAD & CAP. MOVE IN & SPOT / RIG UP GE, HOLD PJSM WITH SAME, REMOVE 7 INCH BIT GUIDE, NU TBG HEAD & CAP FLANGE, TEST BUSHING & FLANGE TO 5000 PSI FOR 10 MIN, RIG DOWN & RELEASE GE. 'ALL VALVES CLOSED / WELL SECURE AT ON 11/2/15" WELL & PAD READY FOR COMPLETION WellEz Information Management, LLC. All rights reserved

2 FIELD: COUNTY/STATE: PMD: PVD: SURFACE LOCATION: BOTTOM HOLE LOCATION: ELEVATION (RKB): Emma Andrews/Texas API #: PERMIT NUMBER: SPUD DATE & TIME: Sep DAYS FROM SPUD: 106 DAYS ON LOCATION: 42 WELL ENGINEER: OBJECTIVE: JOB NAME: University 1-20 #4H CONTRACTOR/RIG#: / DAILY OPERATIONS Dec RIG SUPERVISOR: Tyler Dupriest MIRU Pulling Unit and dress off liner top MIRU Pulling Unit. Move in pipe racks and catwalk, move in and tally 2 7/8" TBG. Move in 4 1/2" Tie back Liner. NU BOP and PU Weatherford polishing mill and RIH on 2 7/8" TBG.;RIH to 10,507' and PU swivel, and begin to polish and mill liner top until clean. POOH and LD 10 joints of TBG and SDFN POOH and LD TBG Dec RIG SUPERVISOR: Tyler Dupriest POOH and LD TBG POOH and LD TBG, and move out TBG. MOVe in Lay Down machine and pipe racks. Move in 4 1/2" Tie back string and SDFN RIH w/ 4 1/2" Tie back liner Dec RIG SUPERVISOR: Tyler Dupriest RIH w/ Tie Back Liner Clean and drift 4 1/2" CSG and subs. PU and RIH with Wetherford Seal extension and 4 1/2" Tie Back Liner. Land Liner with 28K compression. ND BOP and NU hanger flange. RDMO Pulling Unit Dec RIG SUPERVISOR: Tyler Dupriest MIRU Coil TBG Unit for toe prep Toe Prep RDMO Pulling Unit. NU Frac stack. MIRU Coil TBG Unit. Apply 2500 psi to 7" CSG and shut in. Pressure test BOP stack against bottom master valve to 9000 psi, pressure held 15 min. bled down to pit. Pressure test 4 1/2" CSG to 8500 psi for 30 min, pressure bled off 300 psi. Pressure back up to 8500 psi and held for 30 min. Pressure test Coil TBG BOP to 4000 psi and tested good. MU motor, jar, disconnect and 3 3/4" JZ and RIH to Shoe. Tagged 16,365' CTM. POOH to pick up perf guns. Turn well over to night crew.;pooh;picked up Perf Guns and RIH;RIH to 16,361'.;Dropped ball and pumped 81 bbls where ball hit. Pumped but ball wouldn't seat so increased rate to 1.5 bpm ball still didn't seat. Increased rate to 2.0 bpm and then to 2.5 bpm before trying to shut down then pumping again to get ball to seat.;shut flow back in to pressure test and formation broke over at 5,000 psi meaning both guns had been shot. Contacted Tyler to further instructions. Perforations are at 16,347'-16,351', 16,354'-16,358'. Pumped 36 bbls of 15% HCL into formation, closing flow back to inject acid.;pooh;all service companies RDMO location. Shut down for the night. Toe Prep Dec RIG SUPERVISOR: Rocky Vines Prepping location for frac Stuart's NU frac stack to include 2 master valves, flow cross, goat head, crown valve, and wireline night cap. Finish moving pipe racks, accumulator, and BOPs off location. Nabors repaired the manifold on the frac tanks. Water hauler loaded each acid tank with 100 bbls of fresh water in prep for acid delivery. Stuart's finished RU of flow back line. Reserve pit being pulled down.;miru Universal frac, Basin wireline, and Lift crane. Universal will continue to RU tomorrow as well, along with pre-filling sand kings and acid tanks. Dec RIG SUPERVISOR: Rocky Vines MIRU all service companies MIRU all service companies Standby for personnel;universal still rigging up. Acid and sand being off loaded. C&J/Nabors had to bring out 7, 4'' valves and flanges for the fresh water tanks.;finished rigging up iron and attempted to pressure test pump down trucks to finish perforating first stage. Pumps wouldn't pressure test above 6,000 psi.;bucket tested chemical pumps. Pump down pumps were fixed and pressure tested to 8,000 psi. Handed well over to wireline.;rih but to 1,800' when the lubricator started leaking. POOH;RIH and Perforated 16,200'-16,204' 6 spf, 60 phased, 48 holes, using 222 bbls. POOH logging on the way out.;performed Hydration fill up and Loop test. Titrated acid to 21% and 24% HCL.;Pressure tested lines to 9,500' and pressured up the backside to 2,000 psi.;shift change. Finish RU/QA/QC

3 Dec RIG SUPERVISOR: Rocky Vines Hold safety meeting. Get everybody in place.;stage 1 Frac: SICP: 380 psi, formation 1,090 psi, while pumping 3 bpm. Pumped: Total 15% Acid: 119 bbls. Total Slickwater: 3,744 bbls. Total 15# XL Gel: 2,453 bbls. Load to recover for this stage: 6,490 bbls. Pump Down: 0 bbls. Total Load to recover: 6,490 bbls. Containing: Total 100 Mesh: 27,700 lbs, Total 30/50 Ottawa: 85,800 lbs, Total 30/50 Black Ultra: 25,500 lbs. Proppant pumped this stage: 139,000 lbs. Total proppant pumped: 139,000 lbs. ISIP: 2,769 psi, with a Frac Gradient of 0.68 psi/ft. QAvg: 80 bpm, PAvg: 6,260 psi, QMax: 82 bpm, PMax: 8,051 psi. Notes: Stage was difficult to break down. I ran 2 acid spears and extended the slickwater pad stage for formation to break to obtain designed rate. We were not able to get over.75 ppa on 100 Mesh, 2.00 ppa on 30/50 White, and 2.25 ppa on Black Ultra. Stage pumped with all sand away.;stage 2 Wireline: RIH with plug and perf guns. Set 16,090'. Perforate: 16,000'-16,004', 15,800'-15,804'. 6 spf, 48 holes, all shots fired. Total pump down volume: 299 bbls.;stage 2 Frac: SICP: 1,260 psi, formation 5,689 psi, while pumping 5 bpm. Pumped: Total 15% Acid: 167 bbls. Total Slickwater: 2,025 bbls. Total 15# Linear Gel: 2,240 bbls. Total 15# XL Gel: 2,708 bbls. Load to recover for this stage: 7,291 bbls. Pump Down: 299 bbls. Total Load to recover: 13,781 bbls. Containing: Total 100 Mesh: 28,420 lbs, Total 30/50 Ottawa: 85,700 lbs, Total 30/50 Black Ultra: 26,500 lbs. Proppant pumped this stage: 140,620 lbs. Total proppant pumped: 279,620 lbs. ISIP: 2,923 psi, with a Frac Gradient of 0.69 psi/ft. QAvg: 68 bpm, PAvg: 7,252 psi, QMax: 78 bpm, PMax: 8,307 psi. Notes: Stage was difficult to break down again. Ran 2 acid spears and extended the pads but was not able to get over 45 bpm. I sent 100 mesh down at.25 ppa, but almost pressured out when sand hit formation. I ran a slickwater sweep and brought gel on at a 15# linear system. When gel hit formation, pressure rolled over and we were able to obtain 75 bpm. Stage pumped with all sand away, but did not get above 2.00 ppa.;stage 3 Wireline: RIH with plug and perf guns. Set 15,695'. Perforate: 15,600'-15,604', 15,400'-15,404'. 6 spf, 48 holes, all shots fired. Total pump down volume: 185 bbls.;stage 3 Frac: SICP: 1,535 psi, formation 7,430 psi, while pumping 7 bpm. Pumped: Total 15% Acid: 167 bbls. Total Slickwater: 1,901 bbls. Total 15# Linear Gel: 1,142 bbls. Total 15# XL Gel: 2,339 bbls. Load to recover for this stage: 5,533 bbls. Pump Down: 185 bbls. Total Load to recover: 19,314 bbls. Containing: Total 100 Mesh: 26,200 lbs, Total 30/50 Ottawa: 86,200 lbs, Total 30/50 Black Ultra: 26,360 lbs. Proppant pumped this stage: 138,760 lbs. Total proppant pumped: 418,380 lbs. ISIP: 2,961 psi, with a Frac Gradient of 0.70 psi/ft. QAvg: 76 bpm, PAvg: 7,352 psi, QMax: 80 bpm, PMax: 8,102 psi. Notes: I had to extend the slickwater pad to allow formation to break, but not fast enough to carry sand. I brought on the 15# linear gel system early to run the sand and to roll over pressure. Universal's appears to have some bad totes of FR, and will have new totes brought to location. Rest of the stage was pumped as designed with no issues.;stage 4 Wireline: RIH with plug and perf guns. Set 15,295'. Perforate: 15,200'-15,204', 15,000'-15,004'. 6 spf, 48 holes, all shots fired. Total pump down volume: 218 bbls.;"stage 4 Frac: SCIP: 1,403 psi, Formation 5, bpm, 47 bbls total 15% HCL acid, 430 bbls 15# Linear gel, 2,653 bbls 15# XL gel, 2,591 bbls, Slickwater, 39,231 #s 100 Mesh, 124,974 #s 30/50 Ottawa, 24,036 # s 30/50 Black Ultra. Coil pumped: 218 bbls, LTR this stage: 5,940 bbls, Total LTR: 25,254 bbls. Sand pumped this stage: 188,241 #s, Total sand pumped: 606,621 #s. AIP: 7,540 psi, MIP: 7,834 psi, AIR: 69.7 bpm, MIR: 73.5 bpm, ISIP= 3,207 psi, F.G.: 0.72 psi/ft. Notes: Had to shut down during the pad because one of the inside flow cross valves was leaking. Shut down to repair leak then pressure tested again to 9,500 psi before continuing stage. Lost cross linker during final sand stage so stage was cut short with screws cut early.";stage 5 Wireline: RIH with plug and perf guns. Plug did not set POOH after attempting multiple times to set. Charge started to burn but didn't completely burn so the setting tool didn't stroke.;stage 5 Wireline: RIH with plug and perf guns. Set 14,900'. Perforate: 14,800'-14,804', 14,600'-14,604'. 6 spf, 48 holes, all shots fired. Total pump down volume: 342 bbls.;"stage 5 Frac: SCIP: 1,312 psi, Formation 7, bpm, 49 bbls total 15% HCL acid, 288 bbls 15# Linear gel, 2,666 bbls 15# XL gel, 2,564 bbls Slickwater, 39,834 #s 100 Mesh, 119,266 #s 30/50 Ottawa, 26,960 30/50 Black Ultra. Coil pumped: 342 bbls, LTR this stage: 5,910 bbls, Total LTR: 31,164 bbls. Sand pumped this stage: 186,060 #s, Total sand pumped: 792,681 #s. AIP: 7,708 psi, MIP: 8,060 psi, AIR: 67 bpm, MIR: 69.8 bpm, ISIP= 4,773 psi, F.G.: 0.86 psi/ft. Notes: Held sand at 2.0 ppg because of rising pressures. Cut proppant short and flushed well because of pressure.";stage 6 Wireline RIH at time of report

4 Dec RIG SUPERVISOR: Rocky Vines Stage 6 Wireline: RIH with plug and perf guns. Set 14,500'. Perforate: 14,400'-14,404', 14,202'-14,206'. 6 spf, 48 holes, all shots fired. Total pump down volume: 176 bbls.;stage 6 Frac: SICP: 1,260 psi, formation 7,883 psi, while pumping 3 bpm. Pumped: Total 15% Acid: 119 bbls. Total Slickwater: 2,044 bbls. Total 15# Linear Gel: 1,237 bbls. Total 15# XL Gel: 4,080 bbls. Load to recover for this stage: 7,442 bbls. Pump Down: 176 bbls. Total Load to recover: 38,606 bbls. Containing: Total 100 Mesh: 39,420 lbs, Total 30/50 Ottawa: 116,200 lbs, Total 30/50 Black Ultra: 37,500 lbs. Proppant pumped this stage: 193,120 lbs. Total proppant pumped: 985,801 lbs. ISIP: 5,471 psi, with a Frac Gradient of 0.92 psi/ft. QAvg: 73 bpm, PAvg: 7,725 psi, QMax: 76 bpm, PMax: 8,203 psi. Notes: Stage was extremely tight at the beginning. I cut the Kell-Tech's scale inhibitor for a 150 bbls during pad and observed an immediate drop in pressure. I brought the scale back on and observed an immediate slow increase in pressure. Universal has anionic FR on location, which is not reacting well with Kell-Tech's scale inhibitor. They are bring out catanionic FR. Due to this issue, I had to bring gel on early again to roll over pressure. We never got above.75 ppa on the 100 Mesh due to pressure response. The hydration also had issues with the gel pump and lost gel twice during 1.75 ppa 30/50 white. I cut screws and ran a gel sweep, got pressure rolled over, gel back going, and came back on at.50 ppa 30/50 white. We never got above 1.75 ppa and 75 bpm. Stage pumped with all sand away.;stage 7 Wireline: RIH with plug and perf guns. Set 14,100'. Perforate: 14,000'-14,004', 13,806'-13,810'. 6 spf, 48 holes, all shots fired. Total pump down volume: 163 bbls.;standby for cationic FR and Universal's scale inhibitor. We performed fluid tests with cationic FR. The samples with cationic and anionic FR's with Kel-Tech's SI was very clumply and thick. Kel-Tech states that thier SI 625 is anionic. The same cationic FR with Universal's SI looked great. We hooked up Universal's SI and will run it the rest of the job.;stage 7 Frac: SICP: 1,475 psi, formation 6,919 psi, while pumping 5 bpm. Pumped: Total 15% Acid: 119 bbls. Total Slickwater: 1,843 bbls. Total 15# Linear Gel: 1,292 bbls. Total 15# XL Gel: 2,958 bbls. Load to recover for this stage: 6,152 bbls. Pump Down: 163 bbls. Total Load to recover: 44,758 bbls. Containing: Total 100 Mesh: 39,425 lbs, Total 30/50 Ottawa: 120,170 lbs, Total 30/50 Black Ultra: 37,450 lbs. Proppant pumped this stage: 197,045 lbs. Total proppant pumped: 1,182,846 lbs. ISIP: 3,529 psi, with a Frac Gradient of 0.75 psi/ft. QAvg: 73 bpm, PAvg: 7,447 psi, QMax: 75 bpm, PMax: 8,162 psi. Notes: Had to extend the slickwater pad to allow formation to break enough to obtain 65 bpm. I brought on gel early again while on.50 ppa 100 mesh due to pressure response from formation, and never got above 1.25 ppa on 100 mesh. Stage pumped with all sand away, but never got above 2.75 ppa due to pressure response.;stage 8 Wireline: RIH with plug and perf guns. Set 13,700'. Perforate: 13,400'-13,404', 13,600'-13,604'. 6 spf, 48 holes, all shots fired. Total pump down volume: 116 bbls.;gel pump quit working, were down while switching over to backup pump.;"stage 8 Frac: SCIP: 2,019 psi, Formation 7, bpm, 108 bbls total 15% HCL acid, 300 bbls 15# Linear gel, 3,139 bbls 15# XL gel, 3,013 bbls Slickwater, 36,855 #s 100 Mesh, 118,670 #s 30/50 Ottawa, 44,798 30/50 Black Ultra. Wireline pumped: 116 bbls, LTR this stage: 6,677 bbls, Total LTR: 51,435 bbls. Sand pumped this stage: 200,323 #s, Total sand pumped: 1,383,169 #s. AIP: 7,230 psi, MIP: 8,218 psi, AIR: 76.2 bpm, MIR: 80.7 bpm, ISIP= 3,156 psi, F.G.: 0.71 psi/ft. Notes: Stage had pressure issues until Friction Reducer tote was changed then pressure lined out and was smooth. Before switching totes a sweep was added after the during the 1.0 ppg sand stage of 100 mesh. Stage was completed at rate after tote swap.";stage 9 Wireline: RIH with plug and perf guns. Set 13,300'. Perforate: 13,000'-13,004', 13,200'-13,204'. 6 spf, 48 holes, all shots fired. Total pump down volume: 107 bbls.;cleaning Gel pumps and transfering gel from transport.;"stage 9 Frac: SCIP: 2,110 psi, Formation 7, bpm, 84 bbls total 15% HCL acid, 478 bbls 15# Linear gel, 2,651 bbls 15# XL gel, 2,519 bbls Slickwater, 38,970 #s 100 Mesh, 122,635 #s 30/50 Ottawa, 40,772 #s 30/50 Black Ultra. Wireline pump down: 107 bbls, LTR this stage: 5,841 bbls, Total LTR: 57,276 bbls. Sand pumped this stage: 202,377 #s, Total sand pumped: 1,585,546 #s. AIP: 7,432 psi, MIP: 8,053 psi, AIR: 71.4 bpm, MIR: 76.9 bpm, ISIP= 3,121 psi, F.G.: 0.71 psi/ft. Notes: Stage pumped as designed. ";Stage 10 Wireline: RIH with plug and perf guns. Set 12,900'. Perforate: 12,600'-12,604', 12,802'-12,806'. 6 spf, 48 holes, all shots fired. Total pump down volume: 107 bbls.;"stage 10 Frac: SCIP: 1,737 psi, Formation 3, bpm, 82 bbls total 15% HCL acid, 463 bbls 15# Linear gel, 2,578 bbls 15# XL gel, 2,548 bbls Slickwater, 40,045 #s 100 Mesh, 113,599 #s 30/50 Ottawa, 43,440 #s 30/50 Black Ultra. Wireline pump down: 89 bbls, LTR this stage: 5,762 bbls, Total LTR: 63,038 bbls. Sand pumped this stage: 197,084 #s, Total sand pumped: 1,782,630 #s. AIP: 7,254 psi, MIP: 7,967 psi, AIR: 63.3 bpm, MIR: 68.2 bpm, ISIP= 3,565 psi, F.G.: 0.75 psi/ft. Notes: Stage pumped as designed.";rih at time of report.

5 Dec RIG SUPERVISOR: Rocky Vines Stage 11 Wireline: RIH with plug and perf guns. Set 12,500'. Perforate: 12,400'-12,404', 12,200'-12,204'. 6 spf, 48 holes, all shots fired. Total pump down volume: 82 bbls.;stage 11 Frac: SCIP: 1,646 psi, Formation 2, bpm, 119 bbls total 15% HCL acid, 1,599 bbls 15# Linear gel, 2,880 bbls 15# XL gel, 2,578 bbls Slickwater, 39,440 #s 100 Mesh, 124,540 #s 30/50 Ottawa, 37,550 #s 30/50 Black Ultra. Wireline pump down: 82 bbls, LTR this stage: 7,262 bbls, Total LTR: 70,300 bbls. Sand pumped this stage: 201,530 #s, Total sand pumped: 1,984,160 #s. AIP: 7,179 psi, MIP: 8,233 psi, AIR: 77 bpm, MIR: 80 bpm, ISIP= 3,289 psi, F.G.: 0.73 psi/ft. Notes: I extended the slickwater pad to obtain enough rate to start sand, but we almost pressured out when 3200 lbs of 100 mesh at.25 ppa hit formation. I ran a slickwater sweep, but had to bring on gel early, due to low rate, to run the rest of the 100 mesh. Pressure dropped enough to obtain 78 bpm, but had constant pressure spikes and drops for the rest of the stage. No change to backside pressure of the 4.5'' tie back. Rest of stage was pumped as designed with all sand away.;stage 12 Wireline: RIH with plug and perf guns. Set 12,100'. Perforate: 11,994'-11,998', 11,850'-11,854'. 6 spf, 48 holes, all shots fired. Total pump down volume: 54 bbls.;stage 12 Frac: SCIP: 1,664 psi, Formation 3, bpm, 119 bbls total 15% HCL acid, 1,854 bbls 15# Linear gel, 3,561 bbls 15# XL gel, 1,099 bbls Slickwater, 39,400 #s 100 Mesh, 124,740 #s 30/50 Ottawa, 33,526 #s 30/50 Black Ultra. Wireline pump down: 54 bbls, LTR this stage: 6,481 bbls, Total LTR: 76,781 bbls. Sand pumped this stage: 197,666 #s, Total sand pumped: 2,181,826 #s. AIP: 7,724 psi, MIP: 8,166 psi, AIR: 69 bpm, MIR: 78 bpm, ISIP= 5,550 psi, F.G.: 0.93 psi/ft. Notes: I shut down during the slickwater pad due to erratic pressure on the well side. Universal swapped out the transducer and cable and pressures stabilized. I also had to bring on gel early again due to not obtaining enough rate to run sand in slickwater. I ran a 15# XL sweep after.50 ppa 30/50 Ottawa hit formation due to a sharp spike in pressure. Pressure rolled over and I ran the rest of the stage, bringing sand up by.25 ppa concentrations. We never got above 2.75 ppa and 75 bpm, due to rising pressure. Sand was cut while on 2.75 ppa 30/50 Black Ultra, 4000 lbs short. Well was successfully flushed.;stage 13 Wireline: RIH with plug and perf guns. Set 11,750'. Perforate: 11,700'-11,704', 11,550'-11,554'. 6 spf, 48 holes, all shots fired. Total pump down volume: 39 bbls.;stage 13 Frac: SCIP: 1,837 psi, Formation 7,756 9 bpm, 138 bbls total 15% HCL acid, 1,908 bbls 15# Linear gel, 2,852 bbls 15# XL gel, 676 bbls Slickwater, 36,800 #s 100 Mesh, 126,240 #s 30/50 Ottawa, 32,252 #s 30/50 Black Ultra. Wireline pump down: 39 bbls, LTR this stage: 5,398 bbls, Total LTR: 82,179 bbls. Sand pumped this stage: 194,872 #s, Total sand pumped: 2,376,698 #s. AIP: 7,379 psi, MIP: 8,115 psi, AIR: 77 bpm, MIR: 80 bpm, ISIP= 3,089 psi, F.G.: 0.71 psi/ft. Notes: I brought on gel early again due to not being able to get over 44 bpm during the slickwater pad. All 100 mesh was pumped with gel and got up to 1.50 ppa. I also had to lower the rate to 75 bpm when 15# XL hit formation. Rest of stage was pumped as designed with no issues.;stage 14 Wireline: RIH with plug and perf guns. Set 11,450'. Perforate: 11,400'-11,404', 11,250'-11,254'. 6 spf, 48 holes, all shots fired. Total pump down volume: 19 bbls.;stage 14 Frac: SCIP: 1,753 psi, Formation 4, bpm, 83 bbls total 15% HCL acid, 842 bbls 15# Linear gel, 2,589 bbls 15# XL gel, 1,993 bbls Slickwater, 35,725 #s 100 Mesh, 113,740 #s 30/50 Ottawa, 40,886 #s 30/50 Black Ultra. Wireline pump down: 19 bbls, LTR this stage: 5,532 bbls, Total LTR: 87,711 bbls. Sand pumped this stage: 190,351 #s, Total sand pumped: 2,567,049 #s. AIP: 6,854 psi, MIP: 8,022 psi, AIR: 73.8 bpm, MIR: 80.1 bpm, ISIP= 3,525 psi, F.G.: 0.75 psi/ft. Notes: Started gel early because of high pressure, as soon as linear gel came around pressure dropped significantly and we were able to get to 80 bpm. Friction reducer tote was switched during the 2.0 ppg sand stage and pressure dropped over 1,000 psi. Stage pumped as designed.;rih and tubing punch to 10,502' with.375 charges. Wellhead pressure was 1,700 psi with a backside pressure of 850 psi. Shots fired but the pressure didn't equalize. POOH;RIH and tubing punch to 10,501' with.5 charges. Wellhead pressure was 1,200 psi with a backside pressure of 850 psi. Shots fired but the pressure didn't equalize. Pressured up backside to 3,700 psi but wellhead pressure remained 1,200 psi. POOH;RIH and tubing punch to 10,480' with.5 charges. Wellhead pressure was 1,200 psi with a backside pressure of 3,700 psi. Shots fired but the pressure didn't equalize. POOH.;Wireline was out of charges and barrels. Shutdown for the night and waited for more to get here around 6:00 am in the morning. Dec RIG SUPERVISOR: Rocky Vines Tubing punch/prep location for CT drill out Standby for for new charges. Basin load and prep gun.;rih with tubing punch loaded with charges. Set 10,420', with 200 psi on the well, and 600 psi on the backside. We fired the gun but did not see any change in pressure. POOH.;Standby for Basin to bring larger charges.;bason loaded 2, charges. RIH and punched 10,410'. We had 0 psi on the well and 500 psi on the backside. Once we fired, pressure on backside went to 0 psi. POOH.;RDMO Bason wireline and Lift crane. Stuarts ND frac stack down to bottom master valve, NU flow cross on master valve, RU plug catcher, and sand trap. Prep location for CT drill out. Dec RIG SUPERVISOR: Rocky Vines Tubing punch/prep location for CT drill out MIRU service companies for CT drill out Standby for service companies.;miru Xtreme 2 5/8'' CT, Trans Tex N2, Patriot mixing plant, Lift crane, Omni N2 membrane, and Blackhole tools. Xtreme's coil unit did not get to location until 15:00.;Down due to storm blowing into location.;continued to RU, performing pull test to 45,000 lbs before rigging up Coil Connector, Back pressure valve, Jars, Disconnect, BML, Motor, Bit cross over, and JZ Bit (totaling 27.5' in length). Pressure tested well head to 6,000 psi.;n2 foam truck had to replace a fuel filter before well could be opened.;rih while pumping N2 down the Annulus to 10,450' and performed weight check. Pumped 0.5 bpm in while RIH down vertical getting no returns Increased rate to 2.0 bpm with 1,000 scf and started getting returns back but not enough to choke back well. Annulus: 1,450 scf - 1,000 psi;rih to 10,550' and started to get enough returns to choke back well head and pressure came up to 1,200 psi so RIH to first plug. Annulus: 1,450 scf - 2,500 psi;rih and tagged plug 11,459', 2.0 bpm, 1,000 scf, Circ: 2,360 psi, WH: 1200 psi, Annulus: 1,450 scf - 3,200 psi, through plug in 9 minutes, sent 10 bbl gel sweep and waited for it to get to surface before RIH to next plug.;rih and tagged plug 11,758', 2.0 bpm, 1,000 scf, Circ: 2,400 psi, WH: 970 psi, Annulus: 1,440 scf - 3,100 psi, through plug in 15 minutes, sent 10 bbl gel sweep and waited for it to get to surface before RIH to next plug.;rih and tagged plug 12,099', 2.0 bpm, 1,000 scf, Circ: 2,460 psi, WH: 750 psi, Annulus: 1,000 scf - 2,500 psi, through plug in 12 minutes, sent 10/10/10 bbl gel sweep/spacer/sweep and pushed plug down to 12,202' while waiting for sweeps to come around.;short trip at time of report CT drill out

6 Dec RIG SUPERVISOR: Kris Lee Coiled Tubing Plug Drill Out Short trip finished RIH to plug #4. Slip parts very small so a short trip will only be done every 5 plugs or as needed.;rih and tagged plug 12,485', 2.0 bpm, 1,000 scf, Circ: 2,190 psi, WH: 800 psi, Annulus: 1,015 scf - 2,900 psi, through plug in 12 minutes, sent 10 bbl gel sweep and RIH to next plug;rih and tagged plug 12,880', 2.0 bpm, 1,000 scf, Circ: 1,990 psi, WH: 800 psi, Annulus: 1,000 scf - 2,900 psi, through plug in 15 minutes, sent 10 bbl gel sweep and RIH to next plug. Attempted to pump straight fluid instead of mixed fluid with N2 but lost pressure and returns. Started pumping again.;rih and tagged plug 13,281', 3.0 bpm, 1,000 scf, Circ: 3,020 psi, WH: 970 psi, Annulus: 1,000 scf - 3,000 psi, through plug in 12 minutes, sent 10 bbl gel sweep and RIH to next plug. Increased fluid rate because returns were dropping to try and get more returns back.;short tripped because of no returns after plug #6. Sent 10/10/10 bbl sweep. Annulus: 1,000 scf - 3,050 psi. Lost a lot of pressure so sent another 10 bbl sweep. Checked returns and found a lot of sand bogging down fluid.;short tripped because of no returns after plug #6. Sent 10/10/10 bbl sweep. Annulus: 1,000 scf - 3,050 psi. Lost a lot of pressure so sent another 10 bbl sweep. Checked returns and found a lot of sand bogging down fluid.;rih and tagged plug 14,072' 3.0 bpm, 1,000 scf, Circ: 3,030 psi, WH: 680 psi, Annulus: 1,010 scf - 3,000 psi, through plug in 20 minutes, sent 20 bbl gel sweep and RIH to next plug.;rih and tagged plug 14,467' 3.0 bpm, 1,000 scf, Circ: 3,240 psi, WH: 800 psi, Annulus: 1,000 scf - 3,000 psi, through plug in 10 minutes, sent 20 bbl gel sweep and RIH to next plug. Sent a sweep as we RIH to next plug to help lift sand and hopefully help not have to make another short trip.;rih and tagged plug 14,865' 3.0 bpm, 1,000 scf, Circ: 3,360 psi, WH: 630 psi, Annulus: 1,000 scf - 3,000 psi, through plug in 12 minutes, sent 20/10/20 bbl gel sweep and RIH to next plug.;short tripped to 10,550' because of lowering well head pressure. Got back a lot of sand and plug parts.;rih and tagged plug 15,242' 3.0 bpm, 1,000 scf, Circ: 3,070 psi, WH: 680 psi, Annulus: 1,000 scf - 2,950 psi, through plug in 10 minutes, sent 20 bbl gel sweep and RIH to next plug.;rih to plug #12 at time of report. Dec RIG SUPERVISOR: Kris Lee Coiled Tubing Plug Drill Out RIH and tagged plug 15,636' 3.0 bpm, 1,000 scf, Circ: 2,730 psi, WH: 755 psi, Annulus: 1,000 scf - 3,000 psi, through plug in 21 minutes, sent 20 bbl gel sweep and RIH to next plug.;rih and tagged plug 16,037' 3.0 bpm, 1,000 scf, Circ: 2,770 psi, WH: 810 psi, Annulus: 1,000 scf - 3,000 psi, through plug in 15 minutes, sent 20 bbl gel sweep and RIH and tagged bottom at 16,304'. With correction from previous plug depths this is below the bottom perf.;ran 20 bbl sweep and started POOH at 35 feet per minute pumping a 10 bbl sweep every hour with the last sweep out of the coil at 10,600'. Once sweep was on surface we shut down N2 and finished POOH.;Rigging down all third party equipment.;shut down for the night. Dec RIG SUPERVISOR: Tyler Dupriest MIRU Pulling Unit Finish moving out CTU. Move out frac tanks. MIRU Pulling unit, CSG had 2700 psi, blew down to pit but would not die off. Rig up pump truck to flow cross and pump 70 bbls brine DN CSG. ND master valve and flow cross. NU BOP. Move in LD Machine and pipe racks. PU slips and elevators for 4 1/2" CSG. Did not have long enough sub to reach landing hanger, had patriot send a 10' sub. POOH 4 1/2" CSG and LD 2 joints and SDFN. Dec RIG SUPERVISOR: Tyler Dupriest POOH 4 1/2" Tie Back Liner POOH 4 1/2" tie back liner POOH and LD CSG, inspect all connections for bad threads. LD 331 joints and removed last 3 joints and crossover that had been shot with TBG punch. LD seal assembly and shut in well. RDMO LD machine and SDFN. RIH w/ TBG Dec RIG SUPERVISOR: Tyler Dupriest Tally tbg. RIH & stand back tbg Move out 4 1/2" CSG string, move in catwalk and pipe racks. move in and tally 2 7/8" tbg. PU TBG and RIH. POOH and stand back tbg, SDFN Dec RIG SUPERVISOR: Tyler Dupriest Change out rams in bop for reader rams. Spool trailer broke and axle and had to wait for new trailer. RIH with 12 mud joints and spirit desander, make up esp and splice in motor lead. RIH on 2 7/8" TBG. RIH w/ 190 joints and SDFN Dec RIG SUPERVISOR: Tyler Dupriest Cont to. ran 317 joints 2 7/8" TBG. ND BOP, NU landing flange, Make cable splice and land TBG. NU well head and flowback iron. Started ESP, pumped up in 10 min running 50 Hz. Left well going to frac tanks. RDMO pulling unit. none Jan MD: TVD: FOOTAGE: MW: 0.0 LB PTD: RIG SUPERVISOR: Tyler Dupriest PBTD: Additional cost for flowback and water hauling WellEz Information Management, LLC. All rights reserved