Click Here To View Item at

Transcription

1 Click Here To View Item at

2 18 J-2512 EXPLODED VIEW LEFT SIDE , 62 To Anti-Freeze Tank Assy To Anti-Freeze Tank Assy Fuel Line to Engine GENERAL TRAILER MANUAL # / Rev. 2/08

3 1 J-2512 EXPLODED VIEW RIGHT SIDE , , See Plumbing Assembly For Detail See Plumbing Assembly To Storage Tank For 11 Detail See 8 Power Platform Illus GENERAL TRAILER MANUAL # / Rev. 2/08

4 20 J-2512 EXPLODED VIEW PARTS LIST Strap, Tank Tank, 200 Gal PCO, HDPE Constr Bulkhead, /4" Polypro Valve, /4" Stem, 10 Float Elbow, /4" FIPT x FIPT, PVC 80, Ball, Float, Black Plastic Nipple, /4", PVC 80, Close Switch, Float, N/O,. 20 PMDWOP, (Black) Elbow, 1" SLIP x FIPT, PVC 80, Nipple, 1 PVC 80, Close Bulkhead, 1-1/2" Polypro Nipple, 1.5" x ", PVC Elbow, 1-1/2" S x T, PVC 80, Union, 1-1/2" S x S, PVC Pipe, 1.5" PVC " Elbow, 1-1/2" S x S, PVC 80, Nipple, /4" JIC x /4" Pipe Elbow, /4" SAE x /4", 0, Br Light, Strobe Assy, Light Mount Assy, Single Fender, TR Panel, Side Rear, Left Bolt, 5/16"-18 x /4", NC Carriage Zinc Nut, Whiz Loc, 5/16 Flange Panel, Front, Left Strap, MHP Fuel Tank w/hole Tank, Fuel, 10 Gal Poly Red Cap, Fuel Tank, Plastic H60-AV Wheel/Tire Assy., 15" Wheel ST205/75D15 Tire Springs, Leaf, 500 lb Axle, 500 lb, 65 Track, Elec., Brakes Panel, Front Assy, Trailer Jack, Swivel w/caster 1000 lb Breakaway Kit w/battery Bolt, 1/4" x /4" NC HH Nut, 1/4" Flange, Zinc Chain, 5/16" Zinc Plated, 70'/RL, 6" Bolt, /8" x1-1/2" NC, HH, SS Washer, /8" SS Lock Washer, /8" x 1-1/2" Fender Nut, /8" ESNA SS NC Lamp, Side Marker, Amber Screw, #14 x 1" Tek Lamp, Side Marker, Red Screw, #14 x 1" Tek Bracket, Tail Light, Trailers Screw, /8" x /4" HH, NC Whiz Loc Nut, /8" Flange Cover, Light Bracket, Trailers Screw, 1/4" x 1/2" BH SOC CS Jack, Stablizer Bracket, Tank Strap Assy, Tool Box Reel Hose, E Hose, Cox Reel, 100' Reel x 1" Panel, Side Rear Assy, Cone Lock Cone, Traffic Panel, Front Valve, 1.5" Ball, FPT x FPT, Polypro Bulkhead, 1" Polypro Trimloc, 750 B2 x 1/16, Blk, 78" Lock Kit, Hose Reel Clamp, Hose Bolt, /8" Whiz Loc Lamp, Red, Flush Mount Screw, 10/2" x 1/2", BH SOC, Blk Nut, 10/2", Keps Tail Light Assembly, Left Nut, Cage, 1/4" x 12 Ga Screw, /8" x /4", HH, NC Whiz Loc 2 GENERAL TRAILER MANUAL # / Rev. 2/08

5 21 J-2512 EXPLODED VIEW PARTS LIST Nut, Cage, 1/4" x 12 Ga Bulkhead, 1/2" PVC Strain, Relief, WTR Tite Gasket, Neoprene, 7" Bolt, /8" x 1-/4" Tap Nut, ESNA /8" Washer, /8" Bushing, Rubber Dip Tube, 17.75" Label, Gas Only Label, Operating Instructions Label, Danger Cool Engine Label, Warning Connector, Battery Post Box, Battery, M Plate, Battery Box, Large Polypro Instructions, Sheet Not Shipped w/battery Label, General Jet Set 1 76 N /A Chain Guard Plate, Left Panel Cover Nut, Cage 10/2" x 16 Gauge Bushing, 1" x /4" Wire, 6 Ga Red 1.75 ft Wire, 6 Ga Black 1.75 ft Terminal, Ring Tongue Nut, /8" Flange, Whiz Loc Hose, /4" Push-on 102" Cap, Water Tank Screw, 10/2" x 1/2" Ph Pan, MS SS Nipple, 1.5" x ", PVC, Label, Letter "A" Screw, #14 x 1", Tek Hose, 1/4" Push-on, Fuel Line 4" Clamp, Hose Lamp Holder Bolt, /8" x 1", NC HH Bolt, /8" x -1/2" Tap Hanger Kit, Single Axle Grommet, Rubber Nozzle Holder Bracket, Breakaway Trailers Bolt, 1/4" x /4", NC HH Nut, 1/4" Flange, Zn Plug, 7 Prong Trim, 750 B2 x 1/16 Blk, 4" Nut, Wing, 1/4"-20 Zn Bolt, 1/4" x 1", Hex Head, Zinc Connector, 1/2" L/T Straight Screw, 5/16" x /4", Whiz Loc Nipple, 1/2 JIC, 1/2" Pipe Steel Conduit, WTR Tight, Flex, 1/2" 7 ft Hook, "S", 5/16" Zinc Plated Assy Cone Holder, J Bushing,.875" p/n Cable, Throttle, w/knob Nipple, /4" Close Swivel, /4" Fem, HSX /4" Fem Conduit, Flexo, 1/2" Blk, 48" Conduit, Corrugated Tubing 25 ft Connector, Socket, 7 Prong Clamp Hose, CL Screw, # 12 x /4" TEK 1 GENERAL TRAILER MANUAL # / Rev. 2/08

6 22 PLUMBING ASSEMBLY EXPLODED VIEW To Pressure Control Panel To Storage Tank 2 7 To Storage Tank To Supply Hose Reel To Storage Tank Anti-Freeze Tank GENERAL TRAILER MANUAL # / Rev. 2/08

7 2 PLUMBING ASSEMBLY EXPLODED VIEW PARTS LIST Pump, Legacy GX1225/L, 2500, 1725 RPM Cap, Valve w/1/4" Gauge Port Elbow, /4" SAE x /4", 0 Brass Nipple, /4" Close Nipple, /4" Hex Spacer Clips, Clarifier Hose Barb, 1-1/4" x 1" MPT Valve, /4" 8201 Brass Ball Elbow, /4" Female Nipple, 1" Close, PVC Elbow, 1/4" Street Hose, 1/4" x 18.25", 1 Wire 1/4" MPT x /8" MPTS Bushing, /8 x 1/ Tee, 1/2" Branch Male Tee, /4" Female Pipe Elbow, 1/2" JIC, 1/2, Swivel, 1/2" JIC Fem, /8" Mal Cover, Handle V-Pulse, Lg Push-on, 1/2" MPT x /4" Barb Nipple, /8" MPT x M22 Twist Coupler Unloader, PA PSI VB80/ Assy, Slider Nipple, 1/4" Hex Tubing, 1-1/4" Clear Vinyl 25" Elbow, 1" SLIP x FIPT, PVC 80, Union 1", S x S, PVC 80 Spears Tee, 1" FPT x FPT, PVC Valve, 1", 80 PVC, FPT x FPT Molded in Place Swivel, /4" SAE Fem, Push-on Valve, /4" Ball Brass -Way Assy, Anti-Freeze Valve Bracket, MS J Strap, MHP Fuel Tank w/hole Strainer, 40 Mesh Hose, /4" Push-on 2" Hose, /4" Push-on Clear 8" Hose, /4" Suction Push-on SAE 100R4 20" Hose, 1/2" x 0, 2 Wire Pressure Loop, JIC x MPT Tank, Fuel, 10 Gallon Poly Yellow Cap, Fuel Tank, Plastic H60-AV Hanger, Pipe 1-1/2" Click # Bushing, 1" x /4" Barstock Clamp, Screw, #24, P/N Nipple, /4" JIC x /4" Pipe Bushing, 1/2" x /8" Bolt, /8 x 1-/4 Tap Nut, /8, ESNA Washer, / Label, Anti-Freeze Only Label, Legacy, GX Valve, 1/4" Ball Elbow, /4" JIC x 1/2", Bushing, Rubber Elbow, Fuel, Zinc Clamp, Hose Tubing, /8" x 1/2" Clear Vinyl 6" Nipple, /4" JIC x /4" Pipe Knob, Unloader V8, 80/ Hose, /4" Push-on, Clear 57" Clamp, Hose, CL Screw, #14 x1", Tek Clamp, Screw, #12, P/N Hose, /4", Suction, SAE, 100 RH 11" Gasket, Neoprene, 7" Hose, /4" Push-on 102" Screw, 10/2" x 1/2", BH SOC, BLK Nut, 10/2", Keps Coupler, /8" Female, Screw Type Hose, /4" Suction, Push-on SAE 100 R4 4" Label, Letter "E" Label, Letter "B" Label, Letter "D" 1 GENERAL TRAILER MANUAL # / Rev. 2/08

8 24 POWER PLATFORM EXPLODED VIEW GENERAL TRAILER MANUAL # / Rev. 2/08

9 25 POWER PLATFORM EXPLODED VIEW PARTS LIST Engine, Honda GX670TXF2 24 Hp E/S 20 Amp ,ZJ1-861 Assy, Throttle, Honda Muffler, Honda GX620/GX670, Left Bolt, Flange, M8 x Belt Guard, Front Left Assy, Power Platform Assy, Pump Plate Belt Guard, Front Right Pump Assy Bushing, P2 x 1-1/8" Pulley, TB Pulley, 8K 70H Belt, BX Bolt, 1/2" x 5" NC HH Tap, All Thread Pad, Soft Rubber, 50 Duro Bumper Pad, Engine Nut, /8", ESNA, NC Screw, 1/4" x 1/2" HH NC Whiz Loc Nut, Cage, 1/4" x 12 GA Bolt, /8" x 2" NC, HH Washer, /8" SAE Flat Washer 1/2" Flat SAE Nut, 5/16", ESNA, NC Washer, 5/16" Flat, SAE Bushing, H x 25mm Rectifier, Honda 24 HP Nut, 1/2" Hex, NC Bolt, 1/4" x1", Hex Head, Zinc Nut, 1/4" Flange, Zn Washer, /8" x 1-1/2, Fender Label, Warning, Exposed Pulley Deflector, Exhaust, 1-/8" Screw, #10-1/2", Tek, HH, SS (1-/8" Exhaust) A Label, Hot/Caliente, w/arrows Warning Strain Relief, 1/2" Metal Connector, 1/2", L/T Straight Key, SQR x 2.125" Grommet, Rubber Nozzle Label, Letter "C" Hose, 1/2" push on 2" Plug, 1/2" JDC Flare, 6 F Swivel, 1/2" JIC FRM push on Elbow, 1/2" JIC x 1/4" 0 DGR 1 Not Shown GENERAL TRAILER MANUAL # / Rev. 2/08

10 26 ENGINE CONTROL ASSEMBLY Part of Engine Assembly Panel, Control Box, Control Screw, 10/2" x 1/2" BHSOC Blk Nut, Cage, 10/2" x 16 GA Switch, Toggle, 1-1/2" HP, 1 Pole Meter, Tach/Hour, 12 VDC Sendec w/magnet Tool Screw, 6-2" x /4" RH Slot M/S Nut, 6-2" Keps Nut, 10/2" Keps Cable, Throttle w/knob, Capro Procontrol Breaker, Circuit, 50 Amp, Cox Hose Reel Label, General, J-2512, Control Panel Bushing,.875", Pin Screw, 10/2" x /4" BH SOC CS 1 GENERAL TRAILER MANUAL # / Rev. 2/08

11 27 CONTROL PANEL ASSEMBLY 10 From Unloader To High Pressure Hose Reel Relay, 12V Solenoid, Cox Hose Reel Switch, Push-Button, Cox Hose Reel Hose, /8" x 22", 2 Wire, Pressure Loop Hose, 1/2" x 0", 2 Wire, Pressure Loop, JIC x MPT Hose, 1/4" x 16", 2 Wire, Pressure Loop Gauge, PSI General Wire Elbow, 1/4" Female Pipe Tee, 1/2" Street Elbow, 1/2" Street Nipple, 1/2" JIC, 1/2" Pipe Bushing, 1/2" x 1/4" Valve, Ball Panel, Pressure Control Bracket, Valve Lock Label Screw, 1/4" x /4" Elbow, 1/2" JIC x 1/2", Nut, 1/4" Flange ZN Screw, 1/4" x 1/2" BH SOC CS Wire, MTW, 16 Ga, Blk, 24" Terminal, Ring Tongue Terminal Ring Tongue Weatherstrip, 1/8" x 1/2" 20" Screw, /8" x /4" HH, NC, Whiz Loc Nut, /8" Flange, Whiz Loc Adapter, Bracket 1 GENERAL TRAILER MANUAL # / Rev. 2/08

12 28 OPTION D EXPLODED VIEW Hose Reel with Variable Speed Control Part # RESET GENERAL TRAILER MANUAL # / Rev. 2/08

13 2 OPTION D PARTS LIST Hose Reel with Variable Speed Control Part # Controller, Variable Speed Saddle Bracket Hose, /8" x 22", 2 Wire, Pressure Loop Hose, 1/2" x 0", 2 Wire, Pressure Loop, JIC x MPT Hose, 1/4" x 16", 2 Wire Pressure Loop Gauge, PSI General Wire Elbow, 1/4" Female Pipe Tee, 1/2" Street Elbow, 1/2" Street Nipple, 1/2" JIC, 1/2" Pipe Bushing, 1/2" x 1/4" Valve, Ball Panel, Speed Pressure Control Bracket, Valve Lock Label, Speed Pressure Panel Screw, 1/4" x /4" Elbow, 1/2" JIC x 1/2", Nut, 1/4" Flange, ZN Screw, 10/2 x 1/2 BHSOC Nut, 10/2 Keps Nut, 1/4 Flange, ZN Weatherstrip 20" GENERAL TRAILER MANUAL # / Rev. 2/08

14 0 TOOL BOX ,21, ,2 Nozzle Kit (Enlarged View) GENERAL TRAILER MANUAL # / Rev. 2/08

15 1 TOOL BOX PARTS LIST Hose, Garden, /4 x 150' GP, Red 1 Option A Nozzle, 2500 PSI, 12 GPM, 1/2" Set, JNHP Hose, 1/2" x 250' Jet, 250JH 1 Option B Nozzle, 2500 PSI, 12 GPM, 1/2" Set, JNHP Hose, /8" x 250' Jet, 250JH Bushing, 1/2" x /8", Steel 1 Option C Nozzle, 2500 PSI, 12 GPM, 1/2", Set, JNHP Hose, 1/2 x 400' Jet, 400JH D Wand, VP, AL, Soap & 1514 NZL Hose, /8 x 50', 1 Wire, Tuff-Skin /8" MPT x /8" MPS Label, General Gas Warning Label, General Jet Set Retainer, Hose Nut, 1/4" Flange, ZN Bolt, 1/4" x /4" HH NC Spray Gun, Shut-off AP Roller, Aluminum Assy., Hose Guide, J Bushing, Bronze, 5/8" ID x /4" OD Flanged Bolt, 1/2" x -1/2", NC HH Nut, 1/2" ESNA Washer, 1/2" Flat, SAE Bolt, 5/16" x 4-1/4" NC HH Nut, 5/16" ESNA, NC Washer, 5/16" Flat, SAE Knob, Black Plastic Screw, 1/4" x 1-1/4" SHDR Spring,.1 OD x 1.0, Steel Jack, Stabilizer Bolt, /8" x 1", NC HH Nut, /8", ESNA Washer, /8" Flat Washer, /8", SS Lock Lamp, License w/holder Screw, 1/4" x 1/2", HH, NC, Whiz Loc Lamp, Stop, Tail, Turn, Red, Flush Mount Cover, Light Bracket, Trailers Bracket, Tail Light, Trailers Lamp, Side Marker, Red Screw, #14 x 1", Tek, Blk Lamp, Side Marker, Amber Screw, #14 x 1", Tek, Blk Latch, Paddle Handle w/key Screw, 10/2" x 1/2" BH, SOC, SS Nut, 10/2" ESNA Door, Tool Box, J Slide Drawer, 18" 2 pr Screw, 8-2 x 1/2" Nut, 8/2, ESNA Bracket, Hinge Screw, 8-2 x 1/2" Nut, 8/2" ESNA Hinge, 2" x 4" Piano, Stainless Steel Screw, 10/2" x 1/2" BH, SOC, SS Nut, 10/2" ESNA Washer, 1/2" Lock Spacer, Latch, J Screw, 10/2" x 1/2", BH, SOC, SS Nut, 10/2", ESNA Washer, /8" x 1-1/2", Fender Grip, 1" Handle (Waffle) 1 Not Shown GENERAL TRAILER MANUAL # / Rev. 2/08

16 2 WIRING DIAGRAM GENERAL TRAILER MANUAL # / Rev. 2/08

17 WIRING DIAGRAM, OPTION D, VARIABLE SPEED CONTROL GENERAL TRAILER MANUAL # / Rev. 2/08

18 4 JET SET TROUBLESHOOTING These troubleshooting procedures cover pump malfunctions, delivery problems and charge system malfunction. Warning: Before attempting any repairs or maintenance, make sure machine is shut off. PROBLEM POSSIBLE CAUSE REPAIR ENGINE WILL NOT START Low oil level Fill to proper levels. Low water level in 200 gallon tank Fill to 1/2 full minimum. No fuel Fill fuel tank. LOW PRESSURE Worn or oversized nozzle Replace worn nozzle. Check nozzle size. Clogged water supply hose, inlet strainer, Clean or replace strainers. or kinked hose Worn or damaged piston cups Replace piston cups. ROUGH OPERATION WITH LOSS OF PRESSURE Worn or damaged inlet or discharge valve Dirt or foreign particles in valve assembly Air leak in inlet plumbing or inaccurate gauge Cavitation Unloader Worn or plugged relief valve on pump Worn or damaged hose Broken valve spring Pulse valve on Improper adjustment of unloader Restricted inlet plumbing or air leak in inlet plumbing Damaged piston, cup or pump valve Replace worn valve poppets or valve springs. Remove any dirt particles. Locate air leak. Re-seal connection or replace damaged gauge. Check suction lines on inlet of pump for restrictions. Check for proper operation Clean, reset and replace worn parts. Repair/replace hose. Replace spring. Turn off pulse valve. Adjust as necessary. Replace clogged inlet fittings. Check supply hose and ensure adequate water supply. Replace any damaged pump parts and clean out any foreign particles. WATER LEAKAGE AT INTAKE MANIFOLD OR CRANKCASE SHORT PISTON CUP LIFE Clogged nozzles Worn manifold seals, pistons or O-rings. Or, condensation inside crankcase Inadequate water supply to pump creating a vacuum lock Scored cylinders from pumping acids Abrasive particles in fluid being pumped Operator(s) running pump without water supply Hot water in pump Clean or replace nozzles. Replace seals, sleeves or O-rings. Change oil at regular intervals. Ensure adequate tap water supply. Clear inlet filter. Replace cylinders. DO NOT PUMP ACID SOLUTIONS. For acid application, ask your dealer for a Pump Saver Injector. Replace water and detergent strainers if damaged or missing. Install additional filter if fine abrasives are still evident. DO NOT ALLOW WASHER TO BE RUN WITHOUT PROPER WATER SUPPLY. Do not run in bypass for more than 5 minutes. Do not let water supply exceed 140 o F (60 o C). GENERAL TRAILER MANUAL # / Rev. 2/08

19 5 JET SET TROUBLESHOOTING PROBLEM POSSIBLE CAUSE REPAIR WASHER FAILS TO DRAW DETERGENT DETERGENT SOLUTION TOO WEAK DETERGENT SOLUTION TOO CONCENTRATED DETERGENT IN RINSE CYCLE DILUTION OF DETERGENT CONCENTRATE DURING CYCLE Detergent metering valve closed or valve clogged or defective Back pressure in hose (when using additional lengths of pressure hose) Back pressure in pressure hose (when using dual lance wand) Suction tube not below liquid surface Clogged or damaged suction strainer Clogged detergent strainer Air leak in detergent suction tube or inlet plumbing Original detergent too concentrated Dual lance wand or adjustable nozzle holder in open position or chemical metering valve open Worn or defective internal check valve Defective check valve in detergent tank Open detergent metering valve, following procedure in operating instructions. Contact dealer for proper injector size when adding lengths of hose. Use proper size flood nozzle in dual lance wand (refer to parts breakdown). Completely submerge suction tube and strainer in detergent solution. Clean or replace strainer. Clean or replace strainer. Find air leak and clean or replace parts as necessary. Dilute product as necessary to achieve proper concentration. Close dual lance wand adjustable lance holder to achieve high pressure. Close detergent metering valve. Repair or replace check valve or injector parts as necessary. Replace parts as necessary. NOISY OPERATION Worn bearings Replace bearings, refill crankcase oil with recommended lubricant. Cavitation PUMP NOISY Low oil level Add oil Check inlet lines for restrictions and/or proper sizing. IRREGULAR SPRAY PAT- TERN Worn or dirty valves Bad bearings Worn or partially clogged nozzle Replace or clean. Inspect bearings; replace as required Clean or replace nozzles. EXCESSIVE WEAR Worn or loose bearings Replace bearings. Check bearing seals, spacers and retainers. Replace any worn parts. HIGH CRANKCASE TEM- Wrong grade of oil PERATURE USE SAE0 Gear Oil. Improper amount of oil in crankcase Adjust oil level to proper amount. OIL LEAKS Worn pistons and/or leaking crank seals, crankcase cover seal or drain plugs Replace seals, sleeves or O-Rings. GENERAL TRAILER MANUAL # / Rev. 2/08

20 6 JET SET TROUBLESHOOTING Unloader Valve Malfunction PROBLEM POSSIBLE CAUSE REPAIR UNLOADER CYCLES Fitting leaking downstream Tighten/replace fitting. FLUID LEAKING FROM BODY Piston or valve spring broken or worn Clogged nozzle O-ring worn or cut Replace parts as necessary. Clean or replace. Replace part as necessary. UNLOADER WILL NOT COME TO PRESSURE Foreign particle in valve Nozzle worn or wrong size Piston or valve worn Replace or clean. Replace part as necessary. Replace part as necessary. EXTREME PRESSURE SPIKES Adjusting nut turned completely into unloader Clogged nozzle Back off adjusting nut. Clean or replace. GENERAL TRAILER MANUAL # / Rev. 2/08

21 7 General Wire Spring Co. LIMITED ONE YEAR WARRANTY General Wire Spring Co. products are warranted to be free of defects in material and workmanship under normal use for the periods specified below. General machines carry a one year limited warranty against defect or breakage except as noted below. Should any part break or fail to work properly in the year following purchase, it will be repaired or replaced at our discretion at no charge. Some parts, such as hoses and nozzles, are subject to severe wear and are replaced within a year only if a flaw in the material causes breakage. No adjustment can be made on kinked hoses, since a kink is evidence of abuse. Also, no adjustment can be made where there is considerable wear at the point of the break. All parts replaced under warranty must be original General Wire Spring Co. replacement parts. Under no circumstances will General reimburse a service center for parts that are not General parts. Damage due to negligence, rust, exposure to corrosive chemicals, abnormal usage, accidents or alteration from original design is not covered by this warranty. Warranty Does Not Cover: 1. Certain items not manufactured by General but used as components, such as engines and motors, are guaranteed by their respective manufacturer service centers. 2. Items subject to normal wear such as seals, valves, hoses, spray guns, wands, couplings, nozzles, belts, swivels, filters or any part subject to direct physical contact by the public.. Replacement of any fluids such as oil or chemicals, nor does it cover cleaning of any parts. 4. General Wire Spring Co. products are only warranted to the original purchaser, there is no continuation of warranty on used products. 5. Products damaged in transit. (A claim should be filed with the carrier in the event a product is damaged in shipment.) 6. Damage caused by the use of caustic or corrosive liquids. 7. Operating the pump under conditions that cause or contribute to cavitation. 8. Damage caused by contaminated fuel or oil.. Heat damage within the pumping system, whether introduced with the water supply or generated within the system. 10. Damage caused by accident, fire, flood, wind storm, freeze up or other acts of nature. 11. Damage caused by improper installation or power supply. 12. Cost of transportation to authorized service center. 1. Freight costs are the responsibility of purchaser/dealer. 14. Cost incurred for telephone communications. 15. Travel costs or mileage and/or time. 16. Failure to follow recommended maintenance or operating procedures outlined in the operators manual. 17. Loss of running time, income or any other loss due to down time. 18. Use of unauthorized/substandard accessories or attachments. In order to obtain warranty service the original purchaser is responsible for: 1. Providing proof of purchase (original invoice or bill of sale). 2. Informing your wholesaler of the defect(s) or problem(s) and making the product available for repair. They will direct you to the nearest authorized Service Center. (Charges for pick-up or delivery, service calls and mileage are not covered under warranty.) This warranty is made in place of all other warranties, express, statutory or implied, including those of merchantability and of fitness for purpose. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. Some states do not allow the exclusion of limitation of incidental or consequential damages, so these limitations may not apply to you. GENERAL TRAILER MANUAL # / Rev. 2/08

22