SERVICE MANUAL MODEL # ORDER # RG

Transcription

1 SERVICE MANUAL MODEL # ORDER # RG

2

3 CONTENTS Exploded View... 4 Exploded View Parts List... 5 Legacy Axial Pump Troubleshooting... 8 Preventive Manteinance... 9 Oil Change Record

4 PRESSURE WASHER SERVICE MANUAL EXPLODED VIEW

5 ITEM PART NO. DESCRIPTION QTY Pump, Legacy Axial 2.6 GPM 3000PSI Engine Honda GC Key SQR 3/16" x 1 47/64" /16-24 UNF X 1.75 Socket Head Cap Screw Washer, 5/16" Split Ring Lock, Zinc /16-18 X 1-1/2 GR 5 HHCS Zinc Nut, 5/16-18, ESNA Washer, 5/16" Flat, SAE (780452) Powder Coated-P1 Frame Black Wrinkle Wheel & Tire Assy, 10" Steel Rim W/Tube Cap Black Plastic, 5/8'' Rubber Dampener 5/16'' /16-18 X 1/2 Carriage Bolt Label, Rate Specs, Low Label, Regulation Rating Plate, RG Shark, Label Name Plate 1 EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY Label, Operation Warnings Trilingual Caution Engine Oil Tag Open/Closed Sticker-(GCV 160) Quick Start Instruction Guide Sticker Filter with weight Hose DN Motor Oil, SAE-10W 30, 20 oz Powder Coated Handle Hanger LT Side Nut, 5/16, Hex, NC /16 Internal L/W.332 ID X /4-20 Star Knob /4-20 x 1-1/2 GR 2 Hex Bolt Al Bit 101 Trigger Gun Lance-AL Quick Connect-Male 3000 psi Kit, Nozzle (035) Nozzle, 0003, Red Nozzle, 0015, Yellow Nozzle, 0025, Green Nozzle, 0040, White Nozzle, Black, Soaper Hose, HP 5ft, 3600PSI M Name plate Nylon Rivet 1 Not Shown PRESSURE WASHER SERVICE MANUAL 5

6 PRESSURE WASHER SERVICE MANUAL PUMP EXPLODED VIEW AND PARTS LIST * ITEM PART # DESCRIPTION QTY Cylinder Head Valve Assy Horizontal Valve Complete (Kit 3) Nipple Chemestry O-Ring Seal 8.0 x O-Ring Seal, 5.28 x Sphere 7 G Sleeve Helical Spring Nozzle, INS 020/021 Pump Outlet-Thermal Valve O-Ring Seal, x O-Ring Seal 8 x 2 NBR Thermo Valve Tin Coated 1 ITEM PART # DESCRIPTION QTY Helical Spring Unloader Assembly Drain Plug Replacement Plate Hich Pressure Seal Back Ring O-Ring Seal 12.5 x Housing Low Pressure Seal Grooved Ring Spacer Oil Sealing 12.20x4/ Piston Guide O-Ring Seal 15.6 x Male Adapter Filter Seal Female House Conn Gooseneck, Hose Adapter 1 (For pump guard or Filters) Spare Part List, Piston O-Ring Seal 80.0x3.0 NBR70 1 Not Included 6

7 Housing View PUMP EXPLODED VIEW PARTS LIST (CONT) PRESSURE WASHER SERVICE MANUAL ITEM PART # DESCRIPTION QTY Grooved Ball Bearing Swash Plate Hor Ball Bearing No Radial Seal 35 x 52 x Oil Housing 1 7

8 PRESSURE WASHER Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION ENGINE OPERATES FOR 15 MINUTES THEN STOPS Not enough gas or engine oil Vapor lock developed by heat of day Obstruction in fuel fi lter Fill tank with gas. Check oil level. Keep gas tank full to avoid vapor locking. Clean or replace fuel filter. ENGINE LACKS Dirty air filter Replace air filter. POWER ENGINE FALTERS Choke is opened too soon Move choke to halfway position until engine runs smoothly. WATER DRIPPING Piston packing worn Call local distributor. FROM UNDER PUMP O-Ring plunger retainer worn Call local distributor. Cracked piston Call local distributor. OIL DRIPPING Oil seal worn or damaged Call local distributor. WATER LEAKING FROM PUMP PROTECTOR NO DETERGENT TROUBLESHOOTING Spray gun closed with machine Open spray gun or turn off machine. running 5 minutes or longer Excess water supply pressure Place a pressure regulator at end of 50' garden hose. Detergent suction tube not properly connected to machine Detergent is too thick Detergent filter valve is at lowest setting Filter on detergent suction tube is clogged Damaged or clogged detergent suction tube A high pressure nozzle is attached. Check connection. Dilute detergent. For best results, use manufacturers detergent. Set detergent fi lter valve to a higher setting. Run warm water through fi lter to remove debris. Remove obstruction or replace detergent suction tube. Replace with black detergent nozzle. GARDEN HOSE CONNECTION LEAKS SPRAY WAND LEAKS Discharge nozzle is obstructed Loose fittings Missing/worn rubber washer Spray wand not properly attached Blow out or remove debris with fi ne needle. Tighten fittings. Insert new washer. Slide the spray wand into the gun. Turn the wand collar clockwise onto the spray gun threads until tight. Broken o-ring Call local distributor and order an o-ring. PUMP IS NOISY Pump is sucking air Check that hoses and fi ttings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady fl ow of water emerges through nozzle. 8

9 Engine Oil Inspect Change Filter Inspect Air Cleaner/Filter Clean Engine Fuel Filter Spark Plug Maintenance Clean Fuel Tank(s) Replace Fuel Lines Replace High Pressure Nozzle Replace Quick Connects/O-Rings Clean Water Screen/Filter Replace HP Hose PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions. Check pump oil and engine oil level before fi rst use of your new pressure washer. MAINTENANCE SCHEDULE Daily First month or 20 hours. Every 100 hours or every 6 months after fi rst month Every 50 hours Every 50 hours Monthly 500 hours or 6 months 300 hours or annually Annually Annually Every 6 months Annually/As needed Weekly Annually (if there are any signs of wear) PRESSURE WASHER Troubleshooting Guide 9

10 PRESSURE WASHER SERVICE MANUAL Date Oil Changed Month/Day/Year OIL CHANGE RECORD Check pump oil and engine oil level before fi rst use of your new pressure washer. Estimated Operating Hours Since Last Oil Change Date Oil Changed Month/Day/Year Estimated Operating Hours Since Last Oil Change 10

11

12 Form # RG Revised 06/14 Printed in U.S.A. or Mexico