MINIMUM SECURITY LATTICE FACE PLATE GRILLES LINEAR ALUMINUM GRILLES MODULAR CORE DIFFUSERS DIRECTIONAL DIFFUSERS DOOR GRILLES

Transcription

1 MINIMUM SCURITY LATTIC FAC PLAT GRILLS LINAR ALUMINUM GRILLS MODULAR COR DIFFUSRS DIRCTIONAL DIFFUSRS DOOR GRILLS The First Name in Air Diffusion

2 TABL OF CONTNTS CILING AND SIDWALL GRILLS DIFFUSRS ASFP STL LATTIC FAC PLAT APPLICATIONS Corridors Dining facilities Office and common areas Risk Resistant (ASFPRR) Retrofit PAG 4 & 5 PLDMS DIRCTIONAL with PRFORATD FAC PLAT for SNAP IN CILINGS APPLICATIONS Dormitory rooms Office and common areas Psychiatric facilities Risk Resistant PAG 14 & S1MS S2MS SINGL/DOUBL DFLCTION GRILL with LATTIC FAC PLAT APPLICATIONS Office and common areas PAG 6 & 7 RMMS MODULAR COR and STL LATTIC FAC PLAT APPLICATIONS Dormitory rooms Office and common areas DISCONTINUD S MODL QCMS DOOR LOUVR HD3MS STL LOUVR GRILL APPLICATIONS Office and common areas Corridors PAG & 9 PLSL DOOR LOUVR NONVISION INVRTD SPLIT Y with LATTIC FAC PLAT APPLICATIONS Psychiatric facilities Public schools National parks Shelters PAG 1 FIR RATD DOOR LOUVRS SGAL DIFFUSRS SGSDF ALUMINUM LOUVR GRILL APPLICATIONS Dormitory rooms Office and common areas PAG & DIRCTIONAL with LATTIC FAC PLAT APPLICATIONS Dormitory rooms Office and common areas PAG 12 & FLDLULSG1 FLDLULSG2 FUSIBL LINK DOOR LOUVR with LATTIC FAC PLAT APPLICATIONS Psychiatric facilities Public schools National parks Shelters PAG 19 FUSIBL LINK DOOR LOUVR with LATTIC FAC PLATS APPLICATIONS Psychiatric facilities Public schools National parks Shelters PAG 19 TYPICAL SPCIFICATION PAG 2

3 PRODUCT OVRVIW ROUND PRFORATD FAC PATTRNS (ACTUAL SIZ) ASFPRR PLDMS 3/16" Holes on 9/32" Centers 40% Free Area 3/16" Holes on 1/4" Centers 51% Free Area LATTIC FAC PATTRNS (ACTUAL SIZ) 9/16" Holes on /16" Centers 67% Free Area /16" Holes on 1" Centers 66% Free Area HD3MS (ACTUAL SIZ) SGAL (ACTUAL SIZ) Louver Bars Woven Mesh GA Louver Bars on 3/4" Centers with GA Woven Mesh 1/2" on 5/" Centers 1/4" Louver on 1/2" Centers IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention 3

4 ASFP Steel Lattice Face Plate PRODUCT DSCRIPTION MINIMUM SCURITY STANDARD FATURS FAC PLAT: 12 GA C.R.S., with 9/16" square holes on /16" centers TAMPRPROOF SCRWS: # x /2" Pinned Flat Head TORX FINISH STANDARD: White Powder Coat Finish OPTIONAL: Rust Inhibiting Prime Coat. Consult factory for other finishes OPTIONAL FATURS 12 GA. STL FAC PLAT OPPOSD BLAD DAMPR (OPTIONAL) NOMINAL DUCT 3/" ASFP FAC PLAT PATTRNS: /16" square holes on 1" centers 1/4" diameter holes on 3/" staggered centers 5/16" diameter holes on 7/16" staggered centers ASFPRR*...FAC PLAT: 12 GA C.R.S. perforated face with 3/16" diameter holes on 9/32" staggered centers MATRIAL GAUGS: 3/16", GA, 14 GA MATRIAL: Stainless Steel, Aluminum, or Galvanized (consult factory for availability) TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications OPPOSD BLAD DAMPR: front or rear operated, with attached auxiliary frame ADAPTR: square to round (shipped loose) WIDTH 3/" ATTACHD GA AUXILIARY FRAM (OPTIONAL) OPPOSD BLAD DAMPR (OPTIONAL) INSTALLATION The ASFP is installed in the ceiling and secured to the support frame by others. Typical application is for a nonducted return or exhaust unit. See inside back cover, page i, for Installation Overview. HIGHT 3/" HIGHT + 21/2" ASFPRR* 3/16Ó DIA. HOLS ON 9/32 STAGGRD CNTRS Risk Resistant Model *California Title 24 Compliant for Suicide Resistance Performance Data available upon request ASFP 9/16" SQUAR HOLS ON /16" CNTRS 5/" WIDTH + 21/2" * 1 1/2" BORDR IS APPROXIMAT. THIS DIMNSION IS A FUTION OF SIZ AND PRFORATD PATTRN. 1 1/2" TYP. * 4

5 ASFP PRFORMA DATA Supply 9/16" SQUAR HOLS ON /16" CNTRS SIZ 6 x 6 x x 12 x x x 1 6 VL Ps CFM < < < < < < < CFM < < < < < < CFM < < < < < CFM < < < < < CFM < < < < CFM < < < < Test Standard ANSI / ASHRA standard 70 Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands When an opposed blade damper is used, add adjustment as shown below Throw The numbers shown are throw distances, in feet, measured along the jet trajectory axis relating to terminal velocities of 0, 0, & 50 fpm, with the jet attached to a surface. Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. Velocity: Velocity through face plate, feet per minute Pressure P s represents Static Pressure, inches of water OPPOSD BLAD DAMPR (OBD) IRAS ADJUSTMNTS Closing the damper of a register accomplishes two objectives. It restricts the flow of air, thereby increasing the pressure drop and decreasing the cfm. In doing this, the damper also generates sound increases the level. Figure at the right shows the db addition of throttled and unthrottled dampers. For example a damper closed sufficiently to double the pressure loss of a register (pressure ratio of 2) causes an increase of about 7 db. (As a rule of thumb and for general reference only it can be assumed that closing an opposed blade damper to an effective opening ratio of 70 percent doubles the pressure loss of the damper outlet combination. Closing the damper to an effective opening ratio of fifty percent increases the pressure loss to 4 times the grilleopen damper loss.) PRSSUR RATIO THROTTLD DAMPR/OPN DAMPR THROTTLD DAMPR FACTORS IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention 5

6 S1MS/S2MS PRODUCT DSCRIPTION MINIMUM SCURITY Single Deflection Grille (S1MS) Double Deflection Grille (S2MS) with Lattice Face Plate STANDARD FATURS S1MS/S2MS...FAC PLAT: GA C.R.S. with 9/16" square holes on /16" centers Front Louver Direction: Must Specify Vertical (V) i.e. S1MSV/S2MSV Horizontal (H) i.e. S1MSH/S2MSH FRAM: GA C.R.S. with reinforced welded corners TAMPRPROOF SCRWS: # x /2" Pinned Flat Head TORX ADJUSTABL LOUVRS: individually adjustable, single or double deflection 24 GA C.R.S. louvers (spaced 3/4" on centers) FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes GA STL FAC PLAT 24 GA STL ADJUSTABL LOUVRS (SPCIFY DFLCTION AND DIRCTION) 3/4" 4 7/16" OPPOSD BLAD DAMPR (OPTIONAL) RAR LOUVRS (FOR S2MS DOUBL DFLCTION) GA C.R.S. FRAM NOMINAL DUCT 3/" OPTIONAL FATURS S1MS/S2MS face plate patterns : /16" square holes on 1" centers 1/4" diameter holes on 3/" staggered centers 5/16" diameter holes on 7/16" staggered centers MATRIAL GAUGS: face plate 12 GA, 14 GA WIDTH 3/" OPPOSD BLAD DAMPR (OPTIONAL) FAC MOUNTING HOLS MATRIAL: Stainless Steel, Aluminum, (consult factory for availability) XTNDD SLV: (not shown) specify material/gauge/length OPPOSD BLAD DAMPR: front or rear operated HIGHT 3/" HIGHT + 2" ADAPTR: square to round (shipped loose) CONSTRUCTION The S1MS features a heavy duty GA steel face plate behind which is installed either one set (S1MS) or two sets (S2MS) of individually adjustable louvers. INSTALLATION The S1MS/S2MS is designed to be installed through the wall and secured through the face with vandalproof screws or from the back by the locking angles and welded by others to the optional sleeve. See inside back cover, page i, for Installation Overview. 9/16" SQUAR HOLS ON /16" CNTRS WIDTH + 2" * 1 1/2" BORDR IS APPROXIMAT. THIS DIMNSION IS A FUTION OF SIZ AND PRFORATD PATTRN. 1 1/2" TYP. * 6

7 S1MS/S2MS PRFORMA DATA Supply 9/16" SQUAR HOLS on /16" CNTRS ARA FACTOR Ak TYPICAL SIZS SPRAD ANGL 50 THROW MIN. CFM FT MAX. STATIC PRSSUR 75 THROW MIN. CFM FT MAX. STATIC PRSSUR. x4 6x6 0 o.5 45 o o x6 12x5 0 o.5 45 o o x 16x6 0 o.5 45 o o.60 16x 12x12 0 o.5 45 o o.0 30x6 14x12 0 o.5 45 o o x 1x12 0 o.5 45 o o below to 30 to above CFM 0 CFM THROW MIN. FT MAX. STATIC PRSSUR THROW MIN. FT MAX. STATIC PRSSUR CFM 250 CFM THROW MIN. FT MAX. STATIC PRSSUR THROW MIN. FT MAX. STATIC PRSSUR CFM 350 CFM THROW MIN. FT MAX. STATIC PRSSUR THROW MIN. FT MAX. STATIC PRSSUR CFM 450 CFM THROW MIN. FT MAX. STATIC PRSSUR THROW MIN. FT MAX. STATIC PRSSUR THROW MIN. CFM FT MAX. STATIC PRSSUR 600 THROW MIN. CFM FT MAX. STATIC PRSSUR 700 THROW MIN. CFM FT MAX. STATIC PRSSUR 00 THROW MIN. CFM FT MAX. STATIC PRSSUR 900 THROW MIN. CFM FT MAX. STATIC PRSSUR 00 THROW MIN. CFM FT MAX. STATIC PRSSUR THROW MIN. CFM FT MAX. STATIC PRSSUR 1400 THROW MIN. CFM FT MAX. STATIC PRSSUR Test Standard ANSI / ASHRA standard 70 Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands Throw Distance in feet, at which the air has reduced to a terminal velocity, VT, of 125, 0 FPM, (minmax) respectively (isothermal) Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. Pressure P s represents Static Pressure, inches of water AK: Area factor with VK measured using Alnor velometer IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention 7

8 HD3MS Heavy Duty Steel Return Grille Fixed 0 PRODUCT DSCRIPTION MINIMUM SCURITY STANDARD FATURS FAC FRAM: 16 GA C.R.S. LOUVR BARS: specify 0 deflection GA round edge steel spaced 3/4" on centers. LOUVR SUPPORT BARS: GA round edge steel spaced on 6" maximum centers STL WOVN MSH: GA with 1/2" on 5/" centers welded to the frame TAMPRPROOF SCRWS: # x /2" Pinned Flat Head TORX FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes OPTIONAL FATURS MATRIAL GAUG: face frame 14 GA MATRIAL: Stainless Steel, Aluminum, or Galvanized (consult factory for availability) STL SLV GAUG: 14 GA (specify length) LOCKING ANGLS: Two pieces 1" x 1" x 3/16" (shipped loose for field installation) LOCKING ANGL FRAM: 1" x 1" x 3/16" welded one piece steel angle (shipped loose for field installation). Other sizes available consult factory. NOT: SCRW HOLS OMITTD WHN SLV AND LOCKING ANGLS OR LOCKING ANGL FRAM SPCIFID OPPOSD BLAD DAMPR: front or rear operated TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications ADAPTR: square to round (shipped loose) GA RND DG STL LOUVR BARS 3/4" CTRS. GA STL LOUVR SUPPORT BARS MAX 6" CTRS. HIGHT 1/" 3/16" 0 DFLCTION 45/16" 21/16" 1" X 1" X 3/16" STL LOCKING ANGLS (2 PCS., FILD WLDD) WIDTH 1/" "D" SPCIFY SLV LNGTH OPTIONAL OPPOSD BLAD DAMPR 14 GA SLV ORDR SIZ 1/" FAC MOUNTING HOLS HIGHT + 1 7/" CONSTRUCTION The HD3MS is constructed of all steel components with reinforced welded seams and support bars on 6" centers and backed with steel woven mesh welded to the unit to ensure optimum security. INSTALLATION The HD3MS can be installed with security screws through the face or installed through the wall. It is secured from the back by the locking angles and welded by others to the sleeve. (The face mounting screw holes are omitted). See inside back cover, page i, for Installation Overview. WIDTH + 1 7/" 1 1/4" TYP. IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention

9 HD3MS PRFORMA DATA Return Nominal Size Nom Core Core Vel, fpm W H Duct Area Width Height ft2 ft2 Ps CFM < < < < CFM < < < < CFM < < < < CFM < < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < < CFM < CFM < CFM < CFM < Notes: Nominal size represents duct size. Test Standard ANSI / ASHRA standard 70 Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands Pressure P s represents static pressure requirement. Total pressure can be calculated as P t = P s + P v PV is the air velocity pressure in the duct and is calculated as P v = (Velocity/4005) 2 All pressures are stated and calculated in inches of water Opposed Blade Volume Control Dampers (OBD) Increase Static Pressure Ps x 1. when used with an OBD Increase +3 when used with an OBD 9

10 SGAL Aluminum Louver Grille PRODUCT DSCRIPTION MINIMUM SCURITY 0 Deflection (SGAL1) Deflection (SGAL) 45 Deflection (SGAL45) STAKING KY "D" SPCIFY SLV LNGTH GASKT AROUND PRIMTR STANDARD FATURS FRAM: GA extruded aluminum, with 1" face frame width and welded corners PRFORATD SCRN: 14 GA aluminum (50% free area) welded to the frame behind grille core TAMPRPROOF SCRWS: # x /2 Stainless Steel Pinned Flat Head TORX FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes OPTIONAL FATURS SLV MATRIAL: GA aluminum specify length when ordering RINFORCING BARS: 1/4" x 5/" rectangular steel LOCKING ALUMINUM ANGLS: Two pieces 1" x 1" x 3/16" (shipped loose for field installation) LOCKING ALUMINUM ANGL FRAM: 1" x 1" x 3/16" welded one piece steel angle (shipped loose for field installation). Other sizes available consult factory. OPPOSD BLAD DAMPR: installed in the optional sleeve, for front or rear operation, or mounted on the back of the grille TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications ADAPTR: square to round (shipped loose) CONSTRUCTION The SGAL features aluminum bars mechanically fastened to aluminum square rods. The grille core is then welded to the frame to prevent removal. A perforated screen is welded to the frame behind the grille core to prevent concealment of objects. INSTALLATION The SGAL can be installed with security screws through the face or the optional sleeve is welded to the frame for installation through the wall and is secured from the back by the optional locking angles. The locking angles are field welded by others to the sleeve securing it in place. See inside back cover, page i, for Installation Overview. BLAD (SGAL) 45 BLAD (SGAL45) ACTUAL HIGHT (RF. CHART) 0 BLAD (SGAL1) 1/2" TYP. { { { 14 GA. ALUM. PRFORATD SCRN 3/16" OPTION 1 OPTION 2 OPTION 3 ACTUAL WIDTH (RF. CHART) 1 7/" 4 1/4" WIDTH + 1 5/16" GA. ALUMINUM SLV (OPTIONAL) SPCIFY OUTSID DIMNSIONS S CHART BLOW OPPOSD BLAD DAMPR (OPTIONAL) 1" x 1" x 3/16" LOCKING ALUMINUM ANGLS (2 PCS, FILD WLDD) (OPTIONAL) 1/4"x 5/" RCTANGULAR RINFORCING BARS (OPTIONAL) HOW TO DTRMIN OUTSID GRILL DIMNSIONS LOUVR GRILL ONLY GRILL W/OB DAMPR GRILL WITH SLV ACTUAL WIDTH & HIGHT NOM. WIDTH & HIGHT MINUS 9/16" NOM. WIDTH & HIGHT MINUS 3/" NOM. WIDTH MINUS1/32" / NOM. HIGHT PLUS1/" FAC MOUNTING HOLS (OMITTD WITH SLV OPTION) HIGHT + 1 5/16" 1" TYP.

11 SGAL PRFORMA DATA Supply SGAL1 & SGAL DUCT HIGHT 2 2 1/ / CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL CFM/FT Ps THROW SILL WALL Test Standard ANSI / ASHRA standard 70 Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands When an opposed blade damper is used, add adjustment as shown below Throw Distance in feet, at which the air has reduced to a terminal velocity, VT, of 125, 0 FPM. Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. Pressure P s represents Static Pressure, inches of water IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention

12 SGSDF Directional Diffuser Lattice Face Plate PRODUCT DSCRIPTION MINIMUM SCURITY STANDARD FATURS FAC PLAT: 12 GA C.R.S. with /16" square holes on 1" centers. DIFFUSR: with steel construction and reinforced welded corners. 4way pattern is standard. K SIZS: square and rectangular from 6" x 6" to 24" x 24" in 3" increments FAC PLAT: furnished with screw holes to accept 1/4" x 2" tamperproof screws shipped loose. Check ceiling thickness to verify the length is sufficient. TAMPRPROOF SCRWS: 1/4" x 2" oneway vandal proof FINISH STANDARD: White Finish OPTIONAL: Consult factory for other finishes 1/4 WLD NUT/ MOUNTING FRAM ASS'Y 12 GA. STL FAC PLAT DIFFUSR SUPPORT (BY OTHRS) CILING OPNING = NOM. + 3" NOM. K SIZ 3/16" 3/16" FAC PLAT OVRALL = NOM. K SIZ + 5 1/2" /16" 1 31/32" 9/32" 1/4 X 2" ONWAY VANDAL PROOF SCRW OPTIONAL FATURS MATRIAL GAUG: face plate GA, 14 GA MATRIAL: Stainless Steel, Aluminum, or Galvanized (consult factory for availability) FAC PLAT PATTRNS: 9/16" square holes on /16" centers Consult factory for other face patterns OPPOSD BLAD DAMPR: adjustable from the room when the lattice and core are removed (shipped loose) TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications QUALIZING DFLCTOR: Steel duct mounted COR PATTRNS: 1way, 2way opposite, 2WAY corner, 3WAY, 4WAY ADAPTR: square to round (shipped loose) CONSTRUCTION The SGCDF is constructed of all steel components with reinforced welded seams. The heavy duty lattice face plate is removable (with a special tool) to allow access to volume control. INSTALLATION The diffuser is connected to the duct work. The lattice face plate is secured to the diffuser face by the tamperproof screws that extend up into the diffuser support frame in the ceiling. TAMPRPROOF SCRWS (1/4 x 2") ONWAY VANDAL PROOF. HOL LOCATION & QUANTITY VARY WITH SIZ. /16" SQUAR HOLS ON 1" CNTRS 4 WAY PATTRNS (STANDARD) 1 WAY PATTRNS 2 WAY PATTRNS SQUAR NOM. K SIZ + 5 1/2" COR PATTRNS RCTANGULAR L S S L L S S L WAY PATTRNS L S L L S S S L L 12

13 SGSDF PRFORMA DATA Supply K SIZ 6 x 6 9 x 9 12 x 12 x 1 x 1 21 x x 24 PT K VL CFM THROW < < < CFM THROW < < < CFM THROW < < < CFM THROW < < CFM THROW < < CFM THROW < < CFM THROW < < Test Standard ANSI / ASHRA standard 70 Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands Throw The numbers shown are throw distances, in feet, measured along the jet trajectory axis relating to terminal velocities of 0, 0, & 50 fpm, with the jet attached to a surface. Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. Velocity: Feet per minute Pressure P t represents Total Pressure, inches of water IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention

14 PLDMS Directional Diffuser Perforated Face Plate PRODUCT DSCRIPTION MINIMUM SCURITY STANDARD FATURS 231/16 x 231/16 FAC PLAT: 1 GA C.R.S. with 3/16"* holes on 1/4" centers and 90 leg. BACK PAN: GA C.R.S. with adjustable louvers for 1, 2, 3, or 4 way throw. OPTIONAL VOLUM DAMPR (ROUND K SHOWN, SHIPS SPARATLY) ROUND = NOM 1/ SQUAR = NOM 1/4 /2 NONVISIBL SPRING CLIPS K: Square or round neck available 3 FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes 1 GA. PRFORATD FAC PLAT (3/16" DIA. HOLS ON 1/4" STAG. CTRS.) 233/4 X 233/4 (4) ADJUSTABL PATTRN CONTROLLRS SOLID BORDR OPTIONAL FATURS MATRIAL GAUG: face plate 16 GA C.R.S. BACK PAN: tack welded to face plate PRFORATD PATTRNS: Consult factory OPPOSD BLAD DAMPR: front or rear operated V DAMPR BLAD: front operated NON LOUVRD: for return (model 3RPLDMS) MOUNTING: surface mounted with sheet metal screws (snapin L s removed) 3/16" DIA. HOLS ON 1/4" STAG. CTRS. CONSTRUCTION The PLDMS is a two piece unit, constructed of all steel components and consists of commercial grade louvers with an adjustable throw pattern attached within the neck of the back pan. The face plate has an integrated 90 leg for lock down ceiling attachment. INSTALLATION The two piece unit is affixed to itself with nonvisible spring clips. Then the 90 leg of the diffuser is pushed into the TBar lock down ceiling grid system. Contact factory with ceiling grid details to verify compatibility *California Title 24 Compliant for Suicide Resistance 233/4 X 233/4 /2" TYP. SOLID BORDR 14

15 PLDMS PRFORMA DATA Supply SQUAR K SUPPLY Neck Size Neck Velocity, FPM Area Sq. Ft. Pv, Inches WG CFM Ps x x.444 x x x x x Test Standard ANSI / ASHRA standard 70 < < < < Throw, 4way Throw, 3 or 2way Throw, 1way CFM Ps < < < Throw, 4way Throw, 3 or 2way Throw, 1way CFM Ps < < Throw, 4way Throw, 3 or 2way Throw, 1way CFM Ps < < Throw, 4way Throw, 3 or 2way Throw, 1way CFM Ps < Throw, 4way Throw, 3 or 2way Throw, 1way CFM Ps < Throw, 4way Throw, 3 or 2way Throw 1way CFM Ps < Throw, 4way Throw, 3 or 2way Throw, 1way Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands Throw The numbers shown are throw distances, in feet, measured along the jet trajectory axis relating to terminal velocities of 0, 0, & 50 fpm, with the jet attached to a surface. Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. Velocity: Feet per minute Pressure P s represents static pressure requirement. Total pressure can be calculated as P t = P s + P v PV is the air velocity pressure in the duct and is calculated as P v = (Velocity/4005) 2 All pressures are stated and calculated in inches of water IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention

16 RMMS Modular Core Diffuser Lattice Face Plate PRODUCT DSCRIPTION MINIMUM SCURITY STANDARD FATURS FAC PLAT: 12 GA C.R.S. with /16" square holes on 1" centers BACK PAN = NOM. K SIZ + 5 3/16" DIFFUSR: All steel modular core type with welded mitered corners (Anemostat model RM) TAMPRPROOF SCRWS: 1/4" x 3/4" pinned flat head torx MODULAR COR: Field adjustable air pattern (with face plate removed) FINISH 1/4 NUT (WLDD TO BACK PAN) DUCT MTG. HOLS CILING OPNING = NOM. K SIZ + 4 1/4" NOM. K SIZ 1/4" LOW LIMIT OF DUCT 3/4" 3 1/" STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes OPTIONAL FATURS MATRIAL GAUGS: face plates GA, 14 GA MATRIAL: Stainless Steel, Aluminum, or Galvanized (consult factory for availability) CILING / DIFFUSR SUPPORT BY OTHRS (MAX. 1/2" THICK) 1/4 X 3/4 PINND FLAT HAD TORX RMOVABL INNR COR ASSMBLY RQUIRS HOL DRILLD IN COR FOR ACCSS TO DAMPR 12 GA STL FAC PLAT /16" 3/16" FAC PLAT OVRALL = NOM. K SIZ + 6" 1" TYP. ** 1 1/2" TYP. ** DIMNSION IS A FUTION OF SIZ AND PATTRN. FAC PLAT PATTRNS: 9/16" square holes on /16" centers Consult factory for other face patterns TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications DIRCTIONAL AIR PATTRN: 1Way, 2way, 3way, 4way OPPOSD BLAD DAMPR NOT: If opening is framed in, alternate installation method required. ADAPTR: Square to round (shipped loose) CONSTRUCTION The RMMS is constructed of all steel components with reinforced welded seams. The heavy duty lattice face plate is removable (with a special tool) to allow field adjustable air patterns and volume controls. TAMPRPROOF SCRWS (1/4 x 3/4" PINND FLAT HAD TORX) SHIPPD LOOS HOL LOCATION & QUANTITY VARY WITH SIZ INSTALLATION The steel lattice face plate captures the steel ceiling frame between the diffuser face and that of the lattice face. Other methods are with plaster or concrete ceilings where field supplied angles are used to capture the lattice face and the diffuser. /16" SQUAR HOLS ON 1" CNTRS 1 1/2" TYP. NOM. K SIZ + 6" 16 IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention

17 RMMS PRFORMA DATA Supply Nom Neck Size Neck Velocity W H Pt CFM < < < way throw way throw way throw CFM < < < way throw way throw way throw CFM < < way throw way throw way throw CFM < < way throw way throw way throw CFM < < way throw way throw way throw CFM < < way throw way throw way throw CFM < way throw way throw way throw CFM < way throw way throw way throw CFM < way throw way throw way throw CFM < way throw way throw way throw Notes Data is applicable for lattice faces with /16" square holes on 1" centers and 9/16" square holes on /16" centers. Neck velocity is duct velocity, feet per minute. Test Standard ANSI / ASHRA standard 70 Isothermal conditions Throw The numbers shown are throw distances, in feet, measured along the jet trajectory axis relating to terminal velocities of 0,0,& 50 fpm and include a surface effect. Two way throw distance is shown for 2way opposite configuration. Terminal velocity is the air speed, in feet per minute, measured in the supply air stream. For a free jet (no surface effect), throws are 70% of the table values above. Sound Levels is noise criteria curve that will not be exceeded at the operating point. This is determined by assuming a db (ref: 12 watts) room attenuation that is subtracted from the power levels in each of the 2nd thru 7th octave bands Pressure P t represents total pressure, inches of water, for supply. P s static pressure can be calculated by subtracting the Velocity pressure from the Total Pressure (P t ), inches of water All pressures are stated and calculated in inches of water.

18 PLSL PRODUCT DSCRIPTION MINIMUM SCURITY NonVision DOOR GRILL Lattice Face Plate 3/" (mm) 1 3/" MIN (35mm) 3/32" (2mm) STANDARD FATURS FAC PLAT: 12 GA C.R.S. Lattice Face Plate and Security Grille /16" square holes on 1" centers LOUVR BLADS: 1 GA C.R.S. FASTNRS: # x 32 Phillips head thru bolts with blank head one side FR AIR FLOW: 50% free area FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes OPTIONAL FATURS MATRIAL: #304 or #316 stainless steel, #4 finish (satin), hot dipped or zinc plated galvanized TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications FRAM O.D. ORDR SIZ PLUS 2" (51mm) 12 GA. C.R.S. FRAM / SCURITY GRILL FAC PLAT (WITH /16" SQ. HOLS ON 1" CTRS) 1 1/16" (27mm) OUTSID ORDR SIZ MINUS 1/" (3mm) ORDR SIZ & DOOR CUTOUT WIR SCRN: galvanized, aluminum, charcoal aluminum, stainless steel, attached or framed CONSTRUCTION The PLSL is a nonvision inverted split Y" door louver constructed of all steel components (see options) with a removable lattice face security plate. INSTALLATION The PLSL is installed into the door cutout (/" minimum thickness/ 21/4" maximum) by drilling holes through the door to accommodate #32 phillips head thru bolts, with a blank head one side (other tamperproof screws optional), to secure the two louver assemblies to the door. Optional insect screen is available loose or attached. INSID 1

19 FLDLULSG MINIMUM SCURITY Fire Rated Fusible Link DOOR GRILL with Lattice Plate PRODUCT DSCRIPTION FLDLULSG1 STANDARD FATURS FAC PLAT: 12 GA C.R.S. Lattice Face Plate and Security Grille /16" square holes on 1" centers FLDLULSG1 Grille one side FLDLULSG2 Grille two sides LOUVR BLADS: 1 GA C.R.S. FASTNRS: # x 1" Phillips head screw FR AIR FLOW: 40% free area Door Thickness: 1 3/4" FINISH STANDARD: White Powder Coat Finish OPTIONAL: Consult factory for other finishes OPTIONAL FATURS MATRIAL: #304 or #316 stainless steel, #4 finish (satin), or zinc plated galvanized TAMPRPROOF SCRWS: See inside back cover, page i, and consult factory for specific product applications WIR SCRN: galvanized, aluminum, charcoal aluminum, stainless steel attached or framed CONSTRUCTION The FLDLULSG1 or SG2 is a fire rated fusible link door louver constructed of all steel components (see option) with a removable lattice face plate. 160 FUSIBL LINK & HAT SLOT AT TOP STAINLSS RIVTS FINGR PULL (ALWAYS ON LOWR RIGHT HAND SID) 3/4" (19mm) SPRING CLIP 1" (25 mm) 1 3/16" (30 mm) INSID 1 3/4" (44 mm) OR 2" (51mm) 3/32" (5 mm) STOP BLAD OUTSID ORDR SIZ MINUS 1/" (3 mm) 12 GA. C.R.S. FRAM / SCURITYGRILL FAC PLAT (WITH /16" SQ. HOLS ON 1" CTRS) For a 3Dimensional Drawing See Table of Contents page 2 FLDLULSG2 ORDR SIZ & DOOR CUTOUT FRAM O.D. ORDR SIZ PLUS 2" (51 mm) INSTALLATION The FLDLULSG1 or SG2 is installed in door (/4" thick) door cutouts by means of self attaching # x 1" phillips head screws that fasten the auxiliary frame to the louver core through the door cutout the corridor side of the frame is free of fasteners for added security (tamperproof screws optional). Optional insect screens are available loose or attached. FIR RATINGS (WITH UL AND W.H.I. LABL) POSITIV PRSSUR /45/60/90 MINUTS: Approved listing (max width 24", max height 24") (min width 12", min height 6") 12 GA. C.R.S. TWO SIDS FRAM / SCURITY GRILL FAC PLAT (WITH /16" SQ. HOLS ON 1" CTRS) 160 FUSIBL LINK & HAT SLOT AT TOP STAINLSS RIVTS FINGR PULL (ALWAYS ON LOWR RIGHT HAND SID) SPRING CLIP 1" (25 mm) 1 9/16" (40 mm) INSID 1 3/4" (44 mm) OR 2" (51mm) 3/32" (5 mm) STOP BLAD OUTSID ORDR SIZ MINUS 1/" (3 mm) ORDR SIZ & DOOR CUTOUT FRAM O.D. ORDR SIZ PLUS 2" (51 mm) 19

20 TYPICAL SPCIFICATION CILING AND SIDWALL GRILLS ASFP/ASFPRR* MINIMUM SCURITY WITH LATTIC FAC PLAT (PAGS 4 & 5) Contractor shall furnish and install the security face plate, type ASFP (ASFPRR), as herein specified or where shown on plans. The unit shall be as manufactured by Anemostat Products. Security face plate type ASFP shall be 12 GA C.R.S.. The face pattern shall be lattice type with 9/16" square holes on /16" centers (ASFPRR 3/16 holes on 9/32" staggered centers). Tamperproof screws shall be provided by the manufacturer for attaching the face plate to a suitable edge. The ASFP shall be finished with factory white powder coat. S1MS/S2MS MINIMUM SCURITY SINGL/DOUBL DFLCTION GRILL (PAGS 6 & 7) Contractor shall furnish and install the security grilles, type S1VMS, S1HMS, S2VMS, and S2HMS, as herein specified, or where shown on the plans. The unit shall be as manufactured by Anemostat Products. The security grille types shall be all steel construction with reinforced welded corners. The steel blades are individually adjustable. A GA C.R.S. face plate shall cover the unit. The hole pattern for the face plate shall be 9/16" square holes on /16" centers. The frame shall include countersunk screw holes. The number of holes varies with the size of the unit. The S1VMS, S1HMS, S2VMS, and S2HMS shall be finished with factory white powder coat. HD3MS MINIMUM SCURITY STL LOUVR GRILL (PAGS & 9) Contractor shall furnish and install security grilles, type HD3MS, as herein specified, or where shown on plan. The units shall be as manufactured by Anemostat Products. Security grille type HD3MS shall be all steel welded construction. Louver bars are constructed with GA C.R.S., spaced 3/4" on center, and welded to the frame. The louver bars will have zero degree deflection. The frame shall be 16 GA C.R.S. with welded mitered corners. The support bars are welded to the frame, with a maximum (center to center) of 6 inches. The interior screen consists of GA x 1/2" woven steel mesh on 5/" centers. The heavy gauge screen is welded to the frame. The sleeve is constructed of 14 GA C.R.S. and welded to the grille frame. The 3/16" steel locking angles provided are to be field welded by the contractor. The HD3MS and HD3MS units shall be finished with factory white powder coat. SGAL1, SGAL, SGAL45 MINIMUM SCURITY ALUMINUM LOUVR GRILL (PAGS & ) Contractor shall furnish and install the minimum security grilles, type SGAL1, SGAL, and SGAL45, as herein specified, or where shown on plans. The units shall be as manufactured by Anemostat Products. The frame shall be of heavy gauge extruded aluminum, with a 1" border and welded corners. An extruded aluminum grille core will consist of bars 1/4" x 3/4" x 1/2" on centers. The grille support bar will be extruded aluminum. The interior perforated screen shall be 14 GA aluminum. The unit shall be installed with tamperproof screws. The SGAL1, SGAL, and SGAL45 units shall be finished in natural anodize. DIFFUSRS SGSDF MINIMUM SCURITY DIRCTIONAL WITH LATTIC FAC PLAT (PAGS 12 & ) Contractor shall furnish and install security diffusers, type SGSDF, as herein specified, or where shown on plans. The units shall be as manufactured by Anemostat Products. The SGSDF diffuser shall have all steel construction with reinforced welded corners. The SGSDF will consist of a 12 GA C.R.S. face plate with a hole pattern of /16" square holes on 1" centers. The unit shall give a horizontal air discharge pattern. The SGSDF will be mounted with steel tamperproof screws. The SGSDF unit shall be finished with factory white powder coat. PLDMS* MINIMUM SCURITY DIRCTIONAL WITH PRFORATD FAC PLAT FOR LOCK DOWN CILINGS (PAGS 14 & ) Contractor shall furnish and install security diffusers, type PLDMS, designed to fit a LOCKDOWN TBAR Ceiling, as herein specified, or where shown on plans. The units shall be as manufactured by Anemostat Products. The PLDMS will consist of commercial grade louvers with an adjustable throw pattern, attached within the neck (variable sizes available, round or square). The unit is affixed to a standard 1 gauge (optional 16 gauge) perforated faceplate (hole pattern: 3/16" diameter holes on 1/4" staggered centers) sufficient to accommodate the diffuser pan. The faceplate will have 90 leg which is lanced to lock into the TBar grid system. The faceplate is attached to the diffuser pan with nonvisible spring clips (or tack welded). Volume damper assembly available upon request (opposed blade damper or v butterfly damper). NOT: Return unit (3RPLDMS) does not include air pattern assembly. The PLDMS shall be finished with factory white powder coat. DOOR GRILL PLSL MINIMUM SCURITY DOOR LOUVR WITH LATTIC FAC PLAT (PAG 1) Contractor shall furnish and install the security louver, type PLSL, as herein specified, or where shown on plans. The units shall be as manufactured by Anemostat Products. The PLSL security louver is all steel construction with a face plate of 12 GA with /16" square perforations on 1" centers and with louver blades of 1 GA material. The unit shall be furnished with factory white powder coat. FLDLULSG1/FLDLULSG2 MINIMUM SCURITY FIR RATD DOOR LOUVR (PAG 19) Contractor shall furnish and install the security louver, type FLDLULSG1/FLDLULSG2, as herein specified, or where shown on plans. The units shall be as manufactured by Anemostat Products. The FLDLULSG1/FLDLULSG2 fire rated security louver is all steel construction with a face plate of 12 GA with /16" square perforations on 1" centers and with louver blades of 1 GA material. The unit shall be furnished with factory white powder coat. *California Title 24 Compliant for Suicide Resistance IMPORTANT It is the specifier s responsibility to properly configure the HVAC system to meet the appropriate level of comfort, safety, security and detention