PC-125x Counter-Balanced Backdraft Damper

Transcription

1 PC-15x Counter-Balanced Backdraft Damper Product Bulletin Code No. LIT Issued April 7, 015 Refer to the QuickLIT Web site for the most up-to-date version of this document. Since 1885, Johnson Controls has developed and refined air control products by providing the highest quality control dampers that fit your application and size requirements. Now we are including counter-balanced backdraft dampers in our product offering. PC-150 Counterbalanced Backdraft Damper Low velocity Synthetic bearings PC-151 Counterbalanced Backdraft Damper Medium velocity Ball bearings PC-15 Counterbalanced Backdraft Damper High velocity Zytel bearings All three counter-balanced backdraft dampers feature zinc-plated weights. Figure 1: PC-15x Counterbalanced Backdraft Dampers Table 1: Features and Benefits Features 3-Year Warranty on Materials and Workmanship 15 to 5 Working-Day Standard Shipping after Order Entry Benefits Provides confidence in company-backed products. Results in fast response for short lead time projects. PC-15x Counter-Balanced Backdraft Damper Product Bulletin 1

2 Construction Table : Materials Part Materials Frame PC-150: x 1 in T5 extruded aluminum,.090 in. (.3 mm) wall thickness, mitered corners PC-151: 4 x 1 in T5 extruded aluminum,.081 in. (.1 mm) nominal wall thickness PC-15: -1/4 x 1 in T5 extruded aluminum,.15 in. (3. mm) wall thickness Blade PC-150: 0.05 in (.6 mm) formed aluminum with extruded vinyl edge seals PC-151 and PC-15: 6063-T5 extruded aluminum, 0.70 in. (1.8 mm) wall thickness with extruded vinyl edge Counterbalance Zinc-plated weights on blades. Adjustable for final on the job settings. Linkage Tie bars on blade Bearings PC-150: Synthetic PC-151: Dust proof, ball bearings pressed into frame PC-15: Zytel Finish Mill galvanized Sample Specification Furnish and install, at locations shown on plans or in accordance with schedules, counter-balanced backdraft control dampers meeting the following minimum construction standards: Damper frame must be minimum.090 in. (.3 mm) minimum wall thickness, 6063-T5 extruded aluminum with 1 gauge galvanized steel structural brace at each corner. shall be.05 in. (.6 mm) minimum roll-formed aluminum with extruded vinyl blade edge seals mechanically locked into blade edge. Adhesive or clip on type seals are unacceptable. shall include field adjustable, zinc-plated, steel counter-balance weights to allow pressure relief at less at.01 in. wg. Bearings must be corrosive resistant, long life synthetic type for quiet operation. Linkage must be 1/ in. (13 mm) wide tie bar, concealed in the frame. Dampers must be designed for maximum 1500 fpm spot velocities and up to 4 in. wg back pressure, depending on damper size. Dampers shall be in all respects equivalent to Johnson Controls PC-150 damper. Submittal data must include published leakage, pressure drop, and maximum pressure data based on Air Movement and Control Association International (AMCA) Standard 500 testing. Data must cover a full range of damper sizes; data from one size sample is not acceptable. PC-15x Counter-Balanced Backdraft Damper Product Bulletin

3 Damper Dimensions (51) 3 (76) (51) VERTICAL MOUNT HORIZONTAL AIR FLOW (51) Channel FRAME CONSTRUCTION 1 1/ (38) Typ. Front Flange Figure : PC-150 Damper Dimensions, in. (mm) A x B FIG: PC150dims.des 3/4 (70) Max. VERTICAL MOUNT HORIZONTAL AIR FLOW A* x B* 3 1/ (89) Max. FRAME CONSTRUCTIONS STANDARD 1 1/" (38) FLANGE (optional at additional cost) 1" (5) 3 3/8" (86) 4 1/8" (105) Figure 4: PC-151 Damper Dimensions, in. (mm) 1/4" (57) VERTICAL MOUNT HORIZONTAL AIR FLOW Width 1/4" (57) FRAME CONSTRUCTION 1 1/4" (3) Typ. A x B Channel Front Flange Figure 3: PC-151 Damper Dimensions, in. (mm) PC-15x Counter-Balanced Backdraft Damper Product Bulletin 3

4 Performance Curves Performance curves are based on AMCA Standard 500 using test setup apparatus figure 5.3 (damper installed with duct upstream and downstream). Static pressure and cubic feet per minute (cfm) are corrected to.075 lb/cu. ft air density. Table 3: Performance Data for PC-150 Model Damper Width, in. (mm) Maximum Back System Pressure - External Wind Velocity (in. wg) Maximum System Velocity (fpm) Leakage and Pressure Dampers may tolerate higher pressures and velocities than those listed in Table 3, Table 4, and Table 5. Conservative ratings are presented intentionally in an effort to avoid misapplication. Consult a Johnson Controls representative when a damper is to be applied in conditions exceeding recommended maximums. Leakage % of Maximum Flow 1 40 (1,016) 55 mph/1.5 in. wg 1, (914) 70 mph/.5 in. wg 1, (610) 85 mph/3.5 in. wg 1, (305) 95 mph/4.5 in. wg 1, Based on pressure differential of 1 in. wg Table 4: Performance Data for PC-151 Model Damper Width, in. (mm) Maximum Back System Pressure (in. wg) Maximum System Velocity (fpm) Leakage % of Maximum Flow 1 Total sq. ft/ cfm Total sq. ft/cfm Start to Fully 48 (1,19) 4.0 in. wg, in. wg.05 in. wg 36 (914) 8.0 in. wg, ( in. wg, (305) 16.0 in. wg, Based on pressure differential of 1 in. wg Table 5: Performance Data for PC-15 Model Damper Width, in. (mm) Maximum Back System Pressure (in. wg) Maximum System Velocity (fpm) Leakage % of Maximum Flow 1 Total sq. ft/ cfm Start to Fully 48 (1,19) 4.0 in. wg, in. wg.05 in. wg 36 (914) 8.0 in. wg, ( in. wg, (305) 16.0 in. wg, Based on pressure differential of 1 in. wg 4 PC-15x Counter-Balanced Backdraft Damper Product Bulletin

5 Figure 4 shows the air leakage when the PC-151 damper is closed. Figure 5 shows the pressure drop for PC-151 and PC-15 damper models. Note: Ratings are based on AMCA Standard 500 using Test Setup Apparatus Figure 5.3 (damper is installed with ducts upstream and downstream). Static pressure and conversion velocities are corrected to lb/cu. ft air density. PC-150 Horizontal Mount - DOWN Horizontal Mount - UP PC-151 Figure 5: PC-151 Air Leakage (When Damper Closed) Horizontal Mount - DOWN Horizontal Mount - UP PC-15 Horizontal Mount - DOWN Horizontal Mount - UP FIG: upflw.des Figure 6: Pressure Drop Chart (4 x 4 in.) for Models PC-151 and PC-15 Figure 7: Counter-Balanced Backdraft Damper by Damper Model PC-15x Counter-Balanced Backdraft Damper Product Bulletin 5

6 Ordering Information Table 6: PC-15x Industrial Dampers Code Number/Character Product Family Blade Operation Blade Type Bearing/ Seal Type Actuator Type Width Dimensions Height Dimensions Options (Limit ) P = Backdraft/Pressure Relief C = Counter-Balanced H = High Pressure (PC-15) L = Low Pressure (PC-150) M = Medium Pressure (PC-151) N = See Table. N = Normal ALL = 006 through 099 inches 1 inch increments PC-150 = 007 through 099 inches PC-151 = 011 through 099 inches PC-15 = 010 through 099 inches 1 inch increments E = Exact Size F = Front Flange (Air Leaving Side) G = Rear Flange (Air Entering Side) U = Upward Flow Maximum Single Panel Sizes FIELD Ordering Code Number P C L N N - w w w x h h h - - Table 7: Maximum Single Panel Sizes Damper Model Maximum Selection Size PC W x 48 in. H (1,016 x 1,19 mm) PC W x 5 in. H (1,19 x 1,31 mm) PC W x 5 in. H (1,19 x 1,31 mm) 6 PC-15x Counter-Balanced Backdraft Damper Product Bulletin

7 Installation Items Needed nut driver, 5/16 inch socket hammer hole saw, 1-1/4 inch drill bit, 3/16 inch (5 mm), No. 9 or 10 drill No. 1 self-tapping or No machine screws Technical Specifications PC-15x Counter-Balanced Backdraft Dampers 1. Install with frame square. Do not twist or rack the frame square. Use shims between the damper frame and the opening or duct to prevent distortion of the frame square.. Multiple section assemblies must be fastened together on the top, bottom, and all sides. Use appropriate bracing at every horizontal mullion and vertical bracing every 8 feet of damper width. 3. To complete the operation, position blade counter balance weights to set the desired blade opening pressure. 4. For fan discharge applications, locate the damper at least half the fan diameter from fan discharge. Isolation from excessive fan vibration is recommended. Maximum System Pressure PC-150 See Figure 3. PC-151 See Figure 4. PC-15 See Figure 5. Maximum System Velocity PC-150 1,000 feet per minute (305 m per minute) PC-151 and,500 feet per minute (76 m per minute) PC-15 Maximum Temperature -40 F (-40 C) minimum and 00 F (93 C) maximum Shipping Weight PC lb/sq. ft (17. kg/sq. ft) PC lb/sq. ft (17.3 kg/sq. ft) PC lb/sq. ft (17.7 kg/sq.ft) The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication and misuse of its products. Building Efficiency 507 E. Michigan Street, Milwaukee, WI 530 Metasys and Johnson Controls are registered trademarks of Johnson Controls, Inc. All other marks herein are the marks of their respective owners. 015 Johnson Controls, Inc. 7 PC-15x Counter-Balanced Backdraft Damper Product Bulletin Published in U.S.A.