Rod Ends and Spherical Plain Bearings

Transcription

1 Rod Ends and Spherical Plain Bearins

2 Introduction Rod Ends and Spherical Plain Bearins are assembled machine parts to DIN ISO 1224 (former DIN 648), ready for installation. They are used to uarantee the unproblematic movement between shaft and housin, especially where the movement is not directly linear. The FLURO production proram consists of Spherical Plain Bearins in all Series (DIN ISO ) and Rod Ends Series K and E (DIN ISO ), as well as Hydraulic Rod Ends with weld-on surface or female thread fixable with hexaon socket head cap screws. As new products in this cataloue are Thrust Bearins and Anular Contact Spherical Plain Bearins. To supplement the product rane Anle Joints, Fork Heads, Lockin Nuts and Rubber Seals have been added. Where bearins with standard dimensions cannot be used, parts to customer desins are manufactured. Alternatively we can develop solutions for special applications. A small selection of these parts may be seen on the last paes of this cataloue. Our premium trained enineerin and quality uarantee staff is pleased to offer advise on any application demand. With hih standard machinery we are able to turn, rind and mill parts with the hihest precision. A list of our machinin capabilities is available on request. We have been approved for quality assurance to DIN EN ISO 91 since June Our sales staff is happy to assist you with any inquiry. Just recently our industrial unit was enlared and modernized. This meant advanced improvements to our loistics and an enlared stock of products for faster delivery response. 2

3 Contents General Introduction Contents Contents Production Proram FLuROGLIDE /Motorsport Orderin Details Technical Data Thread, Pivotin Anle Fit, Installation Internal Clearance Lubrication, Temperature, Material Technical Information Calculation Examples Rod Ends Series K Standard GI/GA Heavy Duty GIS/GAS Extra Heavy Duty GIXS/GAXS Heavy Duty Stainless Steel GIRS/GARS.. 3 Stainless Steel GIRS..R/GARS..R Heavy Duty Maintenance Free GISW/GASW. 34 ditto Extra Heavy Duty GIXSW/GAXSW Heavy Duty Stainless Steel GIRSW/GARSW. 38 Stainless Steel GIRSW..R/GARSW..R...4 ditto GIRSW..RR/GARSW..RR ditto GIRSW..RR.316/GARSW..RR Stainless Steel GIRSW..NIRO/GARSW..NIRO. 46 Steel on Steel GIO/GAO Steel/PTFE GIOW/GAOW Rod Ends with Seals ditto with Threaded Bolt ditto for Pneumatic Cylinders ditto Stainless Steel GLRS..R Maintenance Free GLXSW ditto Stainless Steel GLRSW Stainless Steel GLRSW..R ditto GLRSW..RR ditto GLRSW..RR Heavy Duty GXS ditto for Stainless Steel GXS..R Maintenance Free GXSW ditto Stainless Steel GXSW..R ditto Stainless Steel GXSW..RR ditto Stainless Steel GXSW..RR Rod Ends Series E Steel on Steel EI(-2RS) / EA 5(-2RS)...72 Maintenance Free EI..D(-2RS)/EA..D(2RS) ditto Stainless Steel EI..D-NIRO(-2RS)/EA..D-NIRO(-2RS) Spherical Plain Bearins Series E Maintenance Free GE...EC (2RS) ditto Stainless Steel GE...EC-NIRO (-2RS).. 71 Steel on Steel GE...E (-2RS) Steel on Steel GE...HO-2RS Inch-sized version GE..ZO (-2RS) Spherical Plain Bearins Series W Steel on Steel GE...LO Spherical Plain Bearins Series G Steel on Steel GE...FO (-2RS) Maintenance Free GE...FW (-2RS) ditto Stainless Steel GE..FW-NIRO (-2RS).. 85 Spherical Plain Bearins Series K Standard GL Heavy Duty GLXS ditto Stainless Steel GLRS Anular Contact Spherical Plain Bearins Steel on Steel GE...SX Maintenance Free GE...SW

4 Contents Spherical Plain Thrust Bearins Steel on Steel GE...AX Maintenance Free GE...AW Rod Ends - Hydraulic with Lockin Device FPR...S ditto for Pneumatic Cylinder FPR...CE short thread FPR...N ditto with Lockin Device FPR...u Heavy Duty with Lockin Device FMA...D.. 94 with Weld-on Surface FS...C with Weld-on Surface FS...N Anle Joints Anle Joints to DIN Fork Heads Fork Heads to DIN and DIN Rubber Seals Rubber Protector Cap RERS Washer Seals RELS Lockin Nuts Lockin Nuts to DIN 934 / ISO Lockin Nuts to DIN 439 / Cylindrical Bearins Description Series BK Series BK1..Bu Thrust washer Du Bearin block for Hydraulic Cylinders Series IKA Series IKB Series DK Bolt for Bearin Block KPA.. / KPB Bolt for bearin block KE.. / KPC.. / KPD Fixin plate for bearin block PPP Fork head for bearin block IF Connectin pin PB Bracket IS../ISS Specials Precision Parts Martin Höhn GmbH Inquiry Template Special Parts Notes Notes Specialties How you can find us u4 DIN EN ISO 91:2 Z.-Re.-Nr TMS Cataloue, Edition 218 Every care has been taken to ensure the accuracy of the information in this cataloue. However, no liability can be accepted for any errors or omissions. Due to continuin technical advances, we reserve the riht to alter our products without notice. Our sales and delivery terms and conditions in the respective valid version, shall apply exclusively for deliveries and other services in commercial business transactions. 4

5 Production Rane Series K Rod Ends DIN ISO Series K Female Thread GI.. Rod Ends DIN ISO Series K Male Thread GA.. Spherical Plain Bearins DIN ISO Series K with / without outer rin GL.. Heavy Duty, Requirin maintenance Heavy Duty, Requirin maintenance Standard-/ Stainless Steel, Maintenance free Standard-/ Stainless Steel, Maintenance free Standard-/ Stainless Steel, Maintenance free Standard-/ Stainless Steel, Maintenance free Steel on Steel Steel on Steel Standard-/ Stainless Steel, Maintenance free Maintenance free Maintenance free Requirin maintenance Requirin maintenance Requirin maintenance GIS.. GIXS.. GIRS.. GIRS..R GAS.. GAXS.. GARS.. GARS..R GLXS.. GLRS.. GLRS..R GISW.. GIXSW.. GIRSW.. GIRSW..R GIRSW..RR GIRSW..RR.316 GIRSW..NIRO GASW.. GAXSW.. GARSW.. GARSW..R GARSW..RR GARSW..RR.316 GARSW..NIRO GLXSW.. GLRSW.. GLRSW..R GLRSW..RR GLRSW..RR.316 GIO.. GAO.. GXS.. GXS..R Standard-/ Stainless Steel, Maintenance free GIOW.. GAOW.. GXSW.. GXSW..R GXSW..RR GXSW..RR.316 5

6 Production Rane Series E Rod Ends DIN ISO Series E Female Thread EI.. EI..-2RS Rod Ends DIN ISO Series E Male Thread EA.. EA..-2RS Spherical Plain Bearins DIN ISO Series E GE..E GE..E-2RS GE..ZO GE..ZO-2RS Stainless Steel Stainless Steel Stainless Steel Maintenance free Maintenance free Maintenance free Steel on Steel Steel on Steel Steel on Steel EI..D EI..D-2RS EA..D EA..D-2RS GE..EC GE..EC-2RS EI..D-NIRO EI..D-NIRO-2RS EA..D-NIRO EA..D-NIRO-2RS GE..EC-NIRO GE..EC-NIRO-2RS Eccentric Rod End with self-alinin roller bearin 6

7 Rod End with shorter thread Bearin with Snap Rin Steel on Steel, Heavy Duty, hiher Pivtoin anle Maintenance free Thrust Bearin FPR..N GE..FO (-2RS) GX..AW Rod End with Lockin Device Bearin with Snap Rin Steel on Steel Ball with Shoulder Steel on Steel Thrust Bearin FMA..D GE..LO GE..AX Rod End with Lockin Device Bearin with Snap Rin Steel on Steel Ball with Shoulder Maintenance free Anular Contact Bearin FPR..CE GE..HO-2RS GE..SW Rod End with Lockin Device Bearin fixed throuh caulkin Circular Weld-on Surface Bearin fixed throuh caulkin Steel on Steel Anular Contact Bearin FPR..S FS..C GE...SX Rod End with Lockin Device Bearin with Snap Rin Rectanular Weld-on Surface Bearin with Snap Rin Maintenance free, Heavy Duty, hiher Pivotin Anle FPR..U FS..N GE..FW (-2RS) GE..FW-NIRO (-2RS) Hydraulic Rod Ends Steel on Steel Hydraulic Rod Ends + Spherical Plain Bearins Steel on Steel Spherical Plain Bearins Production Rane 7

8 Production Rane Anle Joints to DIN 7182 Fork Head to DIN Form C.. / CS.. Anle Joints to DIN 7182 Rubber Seals Lockin Nuts to DIN 934 / 439 RERS Rubber Protector Caps made from Neoprene Cylindrical bearins BK1.. Cylindrical plain bushin G..x.. Fork Head to DIN RELS Washer Seals Rubber Seals with stainless steel washer rins BK1..BU Cylindrical plain bushin with collar with ES-Bolt clevis sprin pin Fork Head to DIN KMR.. KML.. Lockin Nuts with riht hand or left hand threads Washer DU Thrust washer Anle Joints Lockin Nuts / Jam nuts 8

9 Production Rane Bearin block Bracket IKA.. Fork bearin block form A Bearin block Fork head IS.. ISS.. Trunnin bearin block Connectin bolt Fixin plate KPA.. KPB.. Connectin bolt IKB.. Fork bearin block form B IF.. Fork head KPC.. KPD.. KPE.. Connectin bolt rereasable DK.. PB.. Oscillatin bearin block PPP.. Connectin pin Fixin plate Hydraulic Rod Ends 9

10 Special Applications railway vehicles conveyors loadin cranes construction machinery scissors lift shipbuildin 1

11 Custom made products Hydraulic Rod Ends desined and intended for marine, harbor and river enineerin or lock ates. Completely stainless steel to customer desin with maintenance free or rereasable Spherical Plain Bearin. Desin and development accordin to customer requirements. Connectin rod for hihest pressure and tension loads, employed in automotive applications. These parts are supplied completely mounted with required axial distance and torque. 11

12 FLURO Motor Sport Series FLURO has developed a series of Rod Ends and Spherical Plain Bearins, which have zero tolerance throuh preloaded bearin, for Motor Sport applications. RoD ENDS AND SPHERiCAL PLAiN BEARiNGS FoR MoToR SPoRT Exclusive Motor Sport Cataloue on request! SPHERiCAL PLAiN BEARiNGS AND RoD ENDS FoR HEAvy-DuTy APPLiCATioNS For Rod Ends and Spherical Plain Bearins for extreme demands the latest development FLUROGLIDE, a special developped coatin, which is used for Rod Ends and Spherical Plain Bearins with hihest demands, provides a solution. Please ask for our exclusive FLUROGLIDE cataloue 12

13 Orderin Details On paes 5 to 1 we have iven full details of our standard rane of products. Additional notes to make sure details are correct when placin orders are listed below; additions to and deviations from our standard proram are listed, as well. Female Thread: Male Thread: Left Hand Thread: Non-Standard Thread: Stainless Steel Ball: Completely Stainless (Series K): The letter i is situated in the second place in the reference e.. Gi or Ei The letter A is situated in the second place in the reference e.. GA or EA The letter L is situated in the third place in the reference e.. GAL or EAL Bearin reference with additional thread specification e.. GISW 3, M 27x2 The letter R will be added after size reference e.. GIRSW 1 R, GXSW 1 R, stainless version (stainless type see paes 32, 4, 58, 61, 65, 67) The letters RR will be added after size reference e.. GARSW 16 RR, GXSW 16 RR (all items in stainless steel) Completely Stainless (Series E): The letters NiRo will be added after size reference e.. GE 1 EC-NiRo or EI 16 D-NiRo Ball Hard Chrome Plated: Seal: Threaded Bolt: icr will be added after size reference e.. GASW 1 icr -2RS will be added after size reference e.. GISW 1-2RS (see paes 52) Bo will be added after size reference e.. GISW 1 Bo (for riht anle use, see pae 53) Nickel Plated Housin: Special Grease Nipples: Left Hand Thread for Hydraulic Rod Ends: Ni will be added after size reference e.. GISW 14 Ni (improved corrosion resistance for the housin) for series on paes 26 to 29, 34 to 37 SN will be added after size reference e.. GAS 16 SN DIN H1/A M6x1 (exact name of rease nipple has to be specified) The letter L will be added at the third place replacin the letter R e.. FPL...N, except for series FMA...D = FMAL...D For sizes deviatin from the standard or for specials, please send us your drawin or sketch see template on pae 116. The maintenance instructions, selection criteria, tolerances and calculations as shown in the followin technical section are intended to be an important uideline for the choice of the correct bearin to suit the particular application of our Rod Ends and Spherical Plain Bearins. 13

14 Thread, Pivotin Anle Threads Manufactured to standard metric ISO DIN 13 threads. To increase the stability for all standard Rod Ends with male threads, the threads are rolled. Because of the process procedure of zinc platin, it can not be uaranteed that the zinc layer will reach completely into the thread bore of the female rod ends with its complete zinc layer thickness. Pivotin Anle The permissible maximum Pivotin Anle (see picture 3, pae 19) ranes between 6 and 35 dependin on the series and constructional desin. The Pivotin Anle you will find in the product data sheets of series K and series E. The indicated Pivotin Anles are uide values related to situation 2. Other constructional desins and its calculation examples for the Pivotin Anle a are indicated in situations 1 and 3. Situation 1 a = sin -1 B -sin -1 M A A Situation 2 a = sin -1 B - sin -1 M dk dk Situation 3 a = cos -1 D -sin -1 M dk dk A = Outside diameter Rod End/Spherical Plain Bearin B = Width Ball dk = diameter Ball M = Width Rod End/Spherical Plain Bearin D = diameter Bore Ball 14

15 Fit, Installation Recommended fits for the housin's bore to incorporate Spherical Plain Bearins Load hih normal Desin Steel Housin Liht Alloy Housin Steel Series Liht Alloy Housin Series K Series K E / G / W Series E / G / W maintenance free K7 M7 K7 M7 rereasable J7/H7 K7 K7 M7 maintenance free M7 N7 M7 N7 rereasable K7 M7 M7 N7 The outside diameter of the Spherical Plain Bearins, Series K is tolerated to h6. For Series E, please refer to each individual product pae. Recommended fit for the shaft Desin Series K Series E Series G Series W GE..E (-2RS) GE..FO (-2RS) GE..LO GE..EC (-2RS) GE..FW (-2RS) GE..EC-Niro GE..HO-2RS Load hih normal h6 6 6 h6 k6 j6/h6 j6/h6 j6 installation instructions: Attention: No tolerance or play can be allowed for the shaft when incorporated in the Ball or the Outer Rin when incorporated in a housin. Throuh this it is uaranteed that the lide movement arises on the nodular lidin surface only. When mountin extra precaution has to be taken that the press force does not damae the bearin. The press force should not be initiated via the Ball itself. Throuh coolin of the bearin and heatin of the housin the necessary press force will be reduced. Axial lockin of Spherical Plain Bearins: When under hih static or dynamic axial load, vibration, impactin load chanes or hih pivotin anles Spherical Plain Bearins have to be locked axially. Possible lockin methods: - lockin throuh several puncher points - caulkin of bearin on the housin throuh a flanin roove - with lockin snap rins - clamped with bushins on the facin surface of the Insert 15

16 Internal Clearance Internal Clearance is defined as the measure, which can be moved of the radial movement of the ball in the housin or outer rin from a limit position to the opposin. Internal Clearance is measured at room temperature. The axial freedom of movement corresponds approximately to coefficient 3 of the internal clearance. Series K Type Radial internal Clearance in mm (min./max.) Gi/GA; GiS/GAS; 2-1,5 -,35 GiXS/GAXS; 12-2,1 -,4 GiRS/GARS (..R) 22-4,1 -,5 GiSW/GASW; 5-1,5 -,3 GiXSW/GAXSW; 12-18,5 -,35 GiRSW/GARSW 2-25,5 -,45 (..R /..RR /..RR.316 / NiRo) 3-4,5 -,55 GioW/GAoW 4-1,5 -,4 12-2,5 -,5 Gio/GAo 5-1,1 -,5 12-2,1 -,6 GL; GLXS; 2-1,5 -,4 GLRS (..R); 12-18,5 -,5 GXS (..R) 2-25,1 -,6 3-4,1 -,75 4-5,15 -,95 GLXSW; 3-1,5 -,35 GXSW (..R /..RR /..RR.316) 12-18,5 -,4 GLRSW (..R /..RR /..RR.316) 2-25,5 -,5 3-4,1 -,6 4-5,1 -,75 Series E Type Radial internal Clearance in mm (min./max.) Ei/EA 6-12,15 -,5 15-2,2 -, ,3 -,85 4-6,35 -,1 7-8,45 -,12 Ei..D/EA..D (-2RS) 6-12, -,3 Ei..D-NiRo (-2RS) 15-2, -,4 EA..D-NiRo (-2RS) 25-35, -,5 4-6, -,55 7-8, -,6 GE...EC-NiRo (-2RS) 6-12, -, , -, , -,5 4-6, -,6 7-9, -, , -, , -,1 Series E, G, W Type Radial internal Clearance in mm (min./max.) GE...E (-2RS) 4-12,32 -,68 GE...Ho-2RS 15-2,4 -,82 GE...Lo 25-35,5 -,1 4-6,6 -,12 7-9,72 -, ,85 -, ,1 -, ,11 -, ,135 -,261 GE...EC (-2RS) 4-2, -, , -,5 4-6, -,6 7-9, -, ,5 -, ,5 -,14 2-3,8 -,19 GE...Fo (-2RS) 4-1,32 -, ,4 -,82 2-3,5 -,1 35-5,6 -,12 6-8,72 -, ,85 -, ,1 -, ,1 -, ,11 -,214 GE...FW (-2RS) 4-3, -,5 GE..FW-NiRo (-2RS) 35-5, -,6 6-8, -, ,5 -, ,5 -, ,8 -,19 Series Hydraulic Radial internal Clearance in mm (min./max.) FPR...S 1-12,23 -,68 FPR...CE 15-2,3 -,82 FPR...N 25-35,37 -,1 FPR...u 4-6,43 -,12 FMA...D 63-9,55 -,142 FS...C 1-125,65 -,165 FS...N 16-2,65 -,192 For special applications Rod Ends and Spherical Plain Bearins are manufactured with smaller or hiher internal clearance. C2 is smaller (tihter fit) than iven above and C3 is hiher (increased internal clearance) than iven above, available on request. (bitte prüfen... C1 / C) 16

17 Lubrication Temperature Material Lubrication Maintenance Free Rod Ends and Spherical Plain Bearins must not be lubricated. The ball revolves on a PTFE liner incorporated in the housin. Rod Ends with Steel runnin on special Brass, or with Steel runnin on Bronze, and Steel on Steel require reular lubrication. The first time lubrication has to be carried out when the part is mounted. The rereasin interval depends on the impactin influences, such as ambient conditions (temperature, dust, etc) and the mechanical impacts iven throuh the application (surface pressure, number of alternation stress, pivotin anle, lidin speed, etc,). For the lubrication of Spherical Plain Bearins up to a temperature of +11 Celsius, (+23 Fahrenheit) white paste, such as Gleitmo 85k, is recommended. For hiher temperatures from +11 to +22 Celsius, (+23 to +428 ) Fahrenheit we recommend hih temperature rease, such as Notropeen EHT2. Rereaseable Rod Ends Series K are lubricated by means of a rease nipple to DIN 345. For Steel on Steel Rod Ends Series E from size 2 hydraulic rease nipples to DIN are incorporated. Temperature rane FLURO Rod Ends and Spherical Plain Bearins can be operated within the operatin temperatures listed below: Matin surface Material Conversion Table Temperature Celsius Temperature Fahrenheit Steel/Special Brass 5 to to +392 Steel/Bronze 5 to to +48 Steel/PTFE liner 15 to to +48 Steel/PTFE Glass fibre liner 75 to to +32 Steel/Steel 5 to to +392 GE...EC, FW, AW, SW 5 to to +32 GE...-2RS 3 to to +266 GE...EC-NIRO 15 to to +48 PTFE/hard chrome 5 to to +32 From a temperature rane from above +25 C our heavy duty Spherical Plain Bearins are used. Material DiN German France italy Sweden uk usa 1.42 C22 XC25 C M2 M C45 1C45 C M46 Aisi CuSn CuZn4AI Cr6 1Cr6 1Cr S135 Aisi CrMo4 42CrMo4 42CrMo M4 Aisi SMnPb28K S25Pb CF9SMnPb M7 12L X1Cr13 Z1C13 X12Cn C21 Aisi X46Cr13 Z44C14 X4Cr14 42S45 Aisi 42C X2CrNi172 Z15CN16-2 X16CrNi S29 Aisi X9CrMoV18 Aisi 44B X15CrMo17 Z1CD17 Aisi 44C X5CrNi181 Z4CN19-1FF X5CrNi S17 Aisi X1CrNiS189 Z8CNF18-9 X1CrNiS S22 Aisi X5CrNiMo17122 Z7CND X5CrNiMo S17 Aisi X5CrNiCuNb174 Z7CNU15-5 Aisi 63 (174Ph) X6CrNiMoTi Z6CNDT17-12 X6CrNiMoTi S18 Aisi 316Ti 17

18 Technical Information Bearin Load ratins Bearin Load ratins are bearin specific data, derived from the characteristics of the materials used. They are used when selectin Spherical Plain Bearins or Rod Ends for a particular load, but may have to be reduced in adverse operatin conditions. Load ratins C o [ ] C o indicates the maximum permissible static load which a Rod End at its weakest cross section can withstand without developin permanent distortion. The C o values listed in the tables of this brochure have been calculated by usin the appropiate material specifications and have been tested on a number of Rod Ends durin tensile tests carried out at ambient temperature. 8% of the yield strenth resultin from the tests have been used so that a safety factor of 1.25 is included. The static o is also used for establishin the maximum axial load which is limited by an additional bendin stress principally due to the method of fastenin of the insert. Followin are maximum axial values (deformation) which have been established by pressure testin: (1) F a = F a, max = a. C o [ ] a = < ~,4 for GI/GA + GIO/GAO + GXO a = < ~,2 for GXSW, GXS, GL mounted in a FLURO rod end housin a = < ~,1 for EI/EA, EI/EA...D-NIRO For Spherical Plain Bearins C o indicates the radial load, which does not deform the matin surface permanently. Precondition is the stable confiuration of the housin. For applications with threshold or/and alternatin loads, the dynamic load ratin of the rod end housin needs to be considered separately. p max [N/mm 2 ] F St/Ms St/Bz St/St St/St St/TBz St/TNy soft hard constant Table 1: surface pressure Abbreviations: St = Steel, Ms = Brass, Bz = Bronze, TBz = Woven Bronze Fabric, TNy = Woven Nylon Forces affectin a Bearin The loads affectin a Spherical Plain Bearin can vary. They can be: intermittent, constant or variable (illustration 1) static or dynamic f B = 1 f B =,5 variable Time t Picture 1: Load factors - check f B Attention: For Rod Ends with male thread factors choose f B =,35 when load chaneable. Forces when under static load Radial only (F r ) or radial and axial (F a ) forces arise and there is no movement between the ball and the insert (Picture 2). Housin Ball d k Load ratins C [ ] This ratin is used to establish the workin life of Spherical Plain Bearins or Rod Ends when under dynamic load conditions. That is to say when they oscillate, rotate or pivot under load. The values listed in the table result from multiplyin the maximum surface pressure p max admissible in lidin movements by the projected bearin surface. A proj, whereby a specific load tatin is established for each type of Rod End. The established standard values for maximum surface load for various combinations of antio friction material have been listed in table 1 which allows for movement when oscillation. Information: Dependin on the material strenth of the Rod End housin (e. paes 34 and 35) the static load miht be lower than the dynamic load. For this the procedure stated on pae 23 has to be observed. Picture 2: Radial and axial forces Forces when under dynamic load insert Radial or radial and axial forces arise, when the Ball pivots at anle a, oscillates at anle ß or rotates relative to the Insert. 18

19 Technical Information Pivotin anle Housin Ball insert oscillatin anle (3) F m =,1 E F 2. 1 t 1 + F 2. 2 t ) [] Force F [] : time component t [%] therefore the followin must be valid: F i, max F r, max accordin to (6) In case of an additional axial load the equivalent bearin load is calculated accordin to formula (4). (4) F e = F m + Y. F a [ ] Axial factor Y accordin to table 2 F a F a, max accordin to (6a) Picture 3: Pivotin and oscillatin anle In the case of a constant load F r, F a a dynamically equivalent bearin load F e can be established in accordance with formula (2). (2) F e = F r +Y. F a [ ] therefore: F e F r, max accordin to formula (6); F a F a, max (6 a ) The axial factor Y in table 2 is dependent on the load ratio. Load ratio F a : F r,1,2,3,4,5 Axial factor Y,8 1 1,5 2,5 3 Table 2: Axial factor Y In the case of a variable load (picture 4), formula (4) can be used to calculate a mean dynamic bearin load F m from the individual load levels F i and the appropriate time factor t i. Selection of the bearin size The selection is usually made step by step, repeated if necessary, by comparin - 1. the load ratio involved with the normal minimum values for that ratio; 2. the forces affectin the bearin and the maximum permitted load of the bearin proposed; 3. the maximum surface pressure and the surface pressure on the proposed bearins; 4. the maximum lide speed and the lide speed involved of the bearin proposed; 5. the specific performance of the bearin involved with the published cataloue limits. Re 1: The load ratio (C/F) is a value for a specific use of a bearin accordin to formula (5). (5) (C/F) exist (C/F) min The common minimum values for (C/F) for different antifriction surfaces as listed in table 3, can be used to establish the required dynamic load ratin C in accordance with formula (5a) by chanin formula (5). By this means a suitable bearin size can be selected from the tables of this cataloue. Time St/Ms St/Bz St/St St/TBz St/TNy (C/F) min ,75 1,5 Table 3: Typical load ratios Picture 4: Variable load aainst time (5a) C re (C/F) min. F exist [ ] 19

20 Technical Information Re 2: When the existin force affectin the bearin is a static load, it can be used as is for a comparison. When it is a dynamic load, it can be calculated by usin formula (2), (3) or (4). When a Rod End is mounted with a lockin nut or retransfer with two nuts, the additional tensile stress at the male thread or the connectin rod has to be taken into consideration. However the static or dynamic load must always be smaller than the maximum permitted load, which is calculated from the static load ratin C o usin formula (6).This miht have to be further reduced by the load factor f B (picture1) and the temperature factor f T (table4). Temperature C Temperature F reased 1 1 1,8,5 maintenance free 1 1,8,5,3 Table 4: Temperature factor F T (6) F r, max = C o. f B. f T [ ] (6a) F a, max = a. F r, max [ ] If no bearin size is iven in the application the required static load ratin can be established by chanin formula (6) and a Rod End can be selected from the tables accordinly. (7) C o, re Fexist [ ] f B. ft Re 3: The load on a matin surface can be worked out by usin formula (8). It must be less than the standard value for surface load accordin to the antifriction combination of materials, selected as listed in table (1). (8) p exist = p max / (C/F) exist [N/mm 2 ] p max acc.to table1, F acc.to formula (2),(3) or (4) Re 4: The existin averae lide speed v m is calculated accordin to formula (9) usin the frequency of rotation of the crank K and the lide distance of the Spherical Plain Bearin G. (At one rotation of K it corresponds to the double arc b between the centres 1 and 2 in Picture 5 and thus to the double maximum oscillatin anle ß). Picture 5: Oscillatin anle ß relative to crank rotation d k. ß. f (9) v m, exist = 2. b. f = [m/s ] 1. 57,3. 6 Diameter of ball d k [mm] and f [1/min] In case where the bearin rotates fully ß needs to be substituted by 18. The slip speed has to be less than the speed permissible listed in table 5. V max [m/s ] Oscillation Revolution Steel/Steel,15,1 Steel/Bronze (Brass),25 1, Maintenance free,25,35 Table 5: slip speed Re 5: The product p.v can be defined as a specific bearin performance P L (see formula 1). Thus, an estimated value for the heat build-up per mm 2 of the Spherical Plain Bearin surface ist available, mainly dependent on the antifriction material combination, the lubrication/ coolin applied and the surface pressure and lide speed. By increasin temperate the allowable surface pressure of maintenance free bearins is decreasin (picture 1 and 4). (1) P L, exist = p exist. v exist Slip speed v accordin to (9) Surface pressure p accordin to (8) P L, max [W/mm 2 ] N [. m W mm ] 2. = s mm 2 After the selection of the bearin the followin is valid: P L, exist P L, max Steel/Bz, (Brass), (Steel) Maintenance free,5 1,3 Table 6: specific bearin performance short temporary intervals only 2

21 Technical Information Bearin life calculations In the case of a static load it is not necessary to calculate the workin life. The permissible limit set at 8% of the breakin point allows the forces to act indefinitely. In the case of dynamic loads calculatin the bearin life is problematic. There are many, sometimes interdependent influences, that cannot always be taken into consideration.therefore, a calculation of the bearin life can only be approximate. As an approximation the bearin has an increased life proportional to its load ratin and also when used at a moderate speed. Additional influences can be taken into account by makin use of the factors in formula (11). C/F (11) G h 3. f. L f T. fg. fv ( v m ) [h] exist The relubrication factor f v takes into account the extension of the bearin life G h when reularly lubricated. The reater the surface pressure p exist the more often the bearin has to be relubricated. If the bearin is only lubricated on commissionin as in the case of bearins with PTFE liners, f v = 1 has be inserted. p exist [N/mm 2 ] Reular rereasin rereasable bearin Initial reasin + PTFE Table 9: Relubrication factors f v Lubrication intervals are dependent on load conditions and therefore have to be set by the operator. f L = Direction of load to table 7 f T = Temperature factor to table 4 f G = Glide factor to table 8 f V = Relubrication factor to table 9 C/F = Load ratio v m = Mean lide speed [m/s ] The direction of load factor indicates whether the direction of load is uni-directional, constant, variable or oscillatin. Direction of load Steel/Steel Steel/Bz Steel/PTFE unidirectional varyin 2,5 2 1 Table 7: Directional load factors f L The slip factor f G takes into account the materials used on the matin surfaces of a bearin. As a result the only distinction that can be made is between bein maintenance-free (not lubricated) and where lubrication is necessary. (C/F) exist 1, maint. free 1,5 2, 2,5 3, 3,5 4, 4,3 4,7 5, reased 1,1 1,2 1,3 1,4 1,6 1,8 2,1 2,4 2,5 Table 8: Glide factors f G 21

22 Calculation Examples 1. Example: In a paper machine used for manufacturin writin pads a rod end with female thread is used. The dimensions of the components in the machine require size 16, and the followin values are also iven: Variable radial load throuh F r = ± 2 ; No axial load Max. anle of misalinment ß = 2º; Oscillatin interval f = 15/min.; operatin temperature T = +5º Celsius, +122º Fahrenheit Reular lubrication possible 1. initial selection of Rod End a) Type of Rod Ends Series GI, GIS, GIXS, GIRS, GIO can be used when relubricatin. Bearin However, the followin have to be excluded - GIO, because it cannot be lubricated and only moderate movements are possible. - GIRS, a stainless steel type is unneccessary as the workin environment is not corrosive. So we can choose from female rod end types GI, GIS, GIXS. b) The required diameter of the ball is 16 mm and the followin values for GIS can be ascertained from the brochure on paes 26 and 64. d k = 28,6 mm; C o = 32, ; C = 21,5 b 1 ) required static load ratin C o [formula 7 + picture 1 + table 4] C o, req F exist = 2 = 4 f. B f T,5. 1 b 2 ) required dynamic load ratin C [formula 5a + table 3] C req (C/F) min. F exist = 2. 2 = 4 Check C o, exist = 32, > C o, req = 4 C exist = 21,5 > C req = 4 F r = 2 m F r, max = C o. f B. f T = 32,.,5. 1 = 16, 2. Checkin the surface pressure [formula 8 + table 1] p exist = p max = 5 = 5 = 4,65 N/mm 2 < p max = 5 N/mm 2 (C/F) exist 21,5/2 1,75 3. Checkin the slip speed [formula 9 + table 5] v m, exist = d k. ß. f = 28, =,25 m/s < vmax =,25 m/s 1. 57, , Checkin the specific bearin performance [formula 1 + table 6] P L, exist = p exist. v m, exist = 4,65.,25 =,12 W/mm 2 < P L, max =,5 W/mm 2 5. Calculation of bearin life [formula 11 + table ] ( ) G h 3. f. L f. T f. G f. V C/F = , ,75,25 v m exist = 32.5 hrs. 6. Final selection Followin steps 1b to 5. - the calulations for rod ends GI 16 and GIXS 16 can be checked. When makin a decision on the bearin to use, desin, application and price have to be taken into consideration for each type. 22

23 Calculation Examples 2. Example: In a mechanical handlin facility multi-directional radial loads are applied to the rod end. These loads are the same as shown in illustration 4, pae 19. Four separate loads F r, i with the four appropriate time components have been substituted as shown below: F r1 = 2, t 1 = 5%; F r2 = 4, t 2 = 16%; F r3 = 2,4, t 3 = 24%; F r4 = 1, t 4 = 1%; Additionally the rod end is subjected to a constant axial load F a =,65 Further operatin conditions: max. anle ß = 3º; oscillation frequency f = 6/min.; max. temperature 7ºC 1. initial selection of Rod End a) Type of As reular lubrication is not possible due to poor accessibility a maintenance free type must be bearin used. Rod Ends GASW, GAXSW, GARSW, GAOW could be suitable, but the followin series have to be ruled out. - GAOW - these Rod Ends are only suitable for restricted movement. - GARSW - because the workin environment is not corrosive. This leaves the size of the male thread version of type GASW to be established. b) b ) mean and equivalent bearin load [formula table 2] F m =,1 F 2. i t i =,1 E , = 2,46 F e = F m + Y. F a = 2,46 + 1,26.,65 = 3,28 Y = 1,26 for F a /F m =,65/2,46 =,26 b 1 ) required static load ratin C o [formula 7 + picture 1 + table 4] C o, req F exist, e = 3,28 = 6,56 f. B f T,5. 1 b 2 ) required dynamic load ratin C [formula 5a + table 3] C req (C/F) min. F exist = 1,75. 3,28 = 5,75 c) Bearin selected GASW 12 with d k = 22,2 mm and C o = 23,5 C = 32, Check [formula 6 + 6a] C o, exist = 23,5 > C o, req = 6,56 F r2 = 4, F r, max = C o. f B. f T = 23,5.,5. 1 = 11,75 C exist = 32, > C req = 5,75 F a =,65 F a, max = a. F r, max =,2. 11,75 = 2,35 Note: [a =,2 see formula 1] When selectin the size the dynamic req should not exceed the static o, exist 2. Checkin the surface pressure [formula 8 + table 1] p exist = p max = 15 = 15 (C/F) exist 32,/3,28 9,75 = 15,38 N/mm 2 < p max = 15 N/mm 2 3. Checkin the slip speed [formula 9 + table 5] v m, exist = d k. ß. f = 22, , ,3. 6 =,11 m/s < v max =,25 m/s 4. Checkin the specific bearin performance [formula 1 + table 6] P L, exist = p exist. v m, exist = 15,38.,11 =,17 W/mm 2 < P L, max = 1,3 W/mm 2 5. Calculation of bearin life [formula 11 + table ] ( ) G h 3. f. L f. T f. G f. V C/F = ,2. 1 9,75 = 11.1 hrs.,11 v m exist 6. Final selection Steps 1c to 5 can then be repeated for series GAXSW so that after comparin the required material strenth, price etc. of each type, a final decision can be taken. 23

24 Rod Ends Series K - Standard Series Gi Rod End with female thread rereasable throuh rease nipple in the housin Especially suited for axial loads (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 5 8 6, , 7,7 9 M 5 1 9,9 2, , , 8,9 11 M ,9 3, , ,5 1,4 13 M ,1 5, , , 12,9 17 M ,4 7, , ,5 15,4 19 M , 1, , , 16,8 22 M ,5 13, , , 19,3 22 M , 16, , , 21,8 27 M 18x1, , 19, , ,5 24,3 32 M 2x1, ,5 23, , , 25,8 32 M 22x1, , 29, , ,5 29,6 36 M 24x , 35, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned from free-cuttin steel to 9SMnPb28K alvanised, from size 14 fored from heat-treated steel C22, M123 alvanised Special brass to CuZn38Al1 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished Cetop connections see pae

25 Rod Ends Series K - Standard Series GA Rod End with male thread rereasable throuh rease nipple in the housin Especially suited for axial loads (D H7) B M A F L o G GL o Limitin speed rev/min 5 1) 8 6, ,7 M ,3 2, , ,9 M , 3, , ,4 M , 5, , ,9 M ,4 7, , ,4 M ,5 1, , ,8 M ,5 13, , ,3 M ,5 16, , ,8 M 18x1, , 19, , ,3 M 2x1, ,5 23, , ,8 M 22x1, , 29, , ,6 M 24x , 35, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned from free-cuttin steel to 9SMnPb28K alvanised, from size 14 fored from heat-treated steel C22, M123 alvanised Special brass to CuZn38Al1 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished 1) without lubrication hole 25

26 Rod Ends Series K - requirin maintenance Series GiS Rod End with female thread rereasable throuh rease nipple in the housin Especially suited for hih speed applications (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 2 1) 4,5 3, ,5 4,5 3,8 2,6 4, M 2 7 3, 1, ) 6, 4, , 6,5 5, 5,1 5,5 M 3 1 4,1 1, , 6, , 11, 9, 7,7 9, M 5 1 8, 3, , 6, , 13, 1, 8,9 11, M ,9 4, , 9, , 16, 12,5 1,4 13, M ,1 7, , 1, , 19, 15, 12,9 17, M ,3 1, , 12, , 22, 17,5 15,4 19, M ,5 13, , 13, , 25, 2, 16,8 22, M , 17, , 15, , 27, 22, 19,3 22, M , 21, , 16, , 31, 25, 21,8 27, M 18x1, ,5 26, , 18, , 34, 27,5 24,3 32, M 2x1, , 31, , 2, , 37, 3, 25,8 32, M 22x1, , 38, , 22, , 42, 33,5 29,6 36, M 24x , 47, , 25, , 51, 4, 34,8 41, M 3x , 64, , 28, , 58, 46, 37,7 5, M 36x , 8, , 35, , 69, 57, 44,2 6, M 42x , 116, , 45, , 78, 65, 55,9 65, M 48x , 185, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned from free-cuttin steel to 9SMnPb28K alvanised, from size 14 fored from heat-treated steel C22, M123 alvanised 5 turned from heat-treated steel C45 alvanised Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) without lubrication hole 26

27 Rod Ends Series K - requirin maintenance Series GAS Rod End with male thread rereasable throuh rease nipple in the housin Especially suited for hih speed applications (D H7) B M A F L o G GL o Limitin speed rev/min 2 1) 4,5 3, ,5 2,6 M 2 12,6 1, ) 6, 4, , 5,1 M ,5 1, ) 8, 6, , 7,7 M ,3 3, , 6, , 8,9 M , 4, , 9, , 1,4 M , 7, , 1, , 12,9 M ,4 1, , 12, , 15,4 M ,5 13, , 13, , 16,8 M , 17, , 15, , 19,3 M , 21, , 16, , 21,8 M 18x1, ,5 26, , 18, , 24,3 M 2x1, , 31, , 2, , 25,8 M 22x1, , 38, , 22, , 29,6 M 24x , 47, , 25, , 34,8 M 3x , 64, , 28, , 37,7 M 36x , 8, , 35, , 44,2 M 42x , 116, , 45, , 55,9 M 48x , 185, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned from free-cuttin steel to 9SMnPb28K alvanised, from size 14 fored from heat-treated steel C22, M123 alvanised 5 turned from heat-treated steel C45 alvanised Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). 1) without lubrication hole 27

28 Rod Ends Series K - Extra Heavy Duty Series GiXS Rod End with female thread rereasable throuh rease nipple in the housin Especially suitable for hih pressure and tension loads (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 6 9 6, , 8,9 11 M ,7 4, , ,5 1,4 13 M ,5 7, , , 12,9 17 M ,8 1, , ,5 15,4 19 M , 13, , , 16,8 22 M , 17, , , 19,3 22 M ,5 21, , , 21,8 27 M 18x1, ,5 26, , ,5 24,3 32 M 2x1, ,5 31, , , 25,8 32 M 22x1, , 38, , ,5 29,6 36 M 24x , 47, , , 34,8 41 M 3x , 64, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: fored from heat-treated alvanised steel 42CrMo4 Aisi 414 insert: Ball: Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae

29 Rod Ends Series K - Extra Heavy Duty Series GAXS Rod End with male thread rereasable throuh rease nipple in the housin Especially suitable for hih pressure and tension loads (D H7) B M A F L o G GL o Limitin speed rev/min 6 9 6, ,9 M ,8 4, , ,4 M ,5 7, , ,9 M ,4 1, , ,4 M , 13, , ,8 M , 17, , ,3 M ,5 21, , ,8 M 18x1, ,5 26, , ,3 M 2x1, ,5 31, , ,8 M 22x1, , 38, , ,6 M 24x , 47, , ,8 M 3x , 64, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: fored from heat-treated alvanised steel 42CrMo4 Aisi 414 insert: Ball: Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae

30 Rod Ends Series K - stainless housin - requirin maintenance Series GiRS Rod End with female thread rereasable throuh rease nipple in the housin For use in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 3 1) 6 4, ,5 5, 5,1 5,5 M 3 1 8, 1, , , 9, 7,7 9, M ,8 3, , , 1, 8,9 11, M ,1 4, , , 12,5 1,4 13, M ,7 7, , , 15, 12,9 17, M ,3 1, , , 17,5 15,4 19, M ,5 13, , , 2, 16,8 22, M ,5 17, , , 22, 19,3 22, M ,5 21, , , 25, 21,8 27, M 18x1, , 26, , , 27,5 24,3 32, M 2x1, , 31, , , 3, 25,8 32, M 22x1,5 37 1, 38, , , 33,5 29,6 36, M 24x , 47, , , 4, 34,8 41, M 3x , 64, , , 46, 37,7 5, M 36x , 8, , , 57, 44,2 6, M 42x , 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface on request: other slide pairins possible This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) without lubrication hole 3

31 Rod Ends Series K - stainless housin - requirin maintenance Series GARS Rod End with male thread rereasable throuh rease nipple in the housin For use in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 3 1) 6 4, ,1 M , 1, ) 8 6, ,7 M ,2 3, , ,9 M ,8 4, , ,4 M ,1 7, , ,9 M ,5 1, , ,4 M ,5 13, , ,8 M ,5 17, , ,3 M ,5 21, , ,8 M 18x1, , 26, , ,3 M 2x1, , 31, , ,8 M 22x1,5 51 1, 38, , ,6 M 24x , 47, , ,8 M 3x , 64, , ,7 M 36x , 8, , ,2 M 42x , 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface on request: other slide pairins possible This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) without lubrication hole 31

32 Rod Ends Series K - stainless steel - requirin maintenance Series GiRS..R Rod End series K with female thread rereasable throuh rease nipple in the housin For use in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 3 1) 6, 4, ,5 5, 5,1 5,5 M3 1 8, 1, , 6, , 9, 7,7 9, M5 1 11,8 3, , 6, , 1, 8,9 11, M ,1 4, , 9, , 12,5 1,4 13, M8 16 2,7 7, , 1, , 15, 12,9 17, M1 2 28,3 1, , 12, , 17,5 15,4 19, M ,5 13, , 13, , 2, 16,8 22, M ,5 17, , 15, , 22, 19,3 22, M ,5 21, , 16, , 25, 21,8 27, M18x1, , 26, , 18, , 27,5 24,3 32, M2x1, , 31, , 2, , 3, 25,8 32, M22x1,5 37 1, 38, , 22, , 33,5 29,6 36, M24x , 47, , 25, , 4, 34,8 41, M3x , 64, , 28, , 46, 37,7 5, M36x , 8, , 35, , 57, 44,2 6, M42x , 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 Stainless steel to 1.434, hardened, round, polished on request: other slide pairins possible This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) without lubrication hole 32

33 Rod Ends Series K - stainless steel - requirin maintenance Series GARS..R Rod End series K with male thread rereasable throuh rease nipple in the housin For use in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 3 1) 6 4, ,1 M3 15 7, 1, ) 8 6, ,7 M5 19 6,2 3, , ,9 M6 21 8,8 4, , ,4 M ,1 7, , ,9 M ,5 1, , ,4 M ,5 13, , ,8 M ,5 17, , ,3 M16 4 6,5 21, , ,8 M18x1, , 26, , ,3 M2x1, , 31, , ,8 M22x1,5 51 1, 38, , ,6 M24x , 47, , ,8 M3x , 64, , ,7 M36x , 8, , ,2 M42x , 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 Stainless steel to 1.434, hardened, round, polished on request: other slide pairins possible This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) without lubrication hole 33

34 Rod Ends Series K - Maintenance Free Series GiSW Rod End with female thread and PTFE liner For use at dynamic loads (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 5 8 6, , 7,7 9 M 5 1 8, 7, , , 8,9 11 M ,9 9, , ,5 1,4 13 M ,1 16, , , 12,9 17 M ,3 23, , ,5 15,4 19 M ,5 32, , , 16,8 22 M , 42, , , 19,3 22 M , 52, , , 21,8 27 M 18x1, ,5 64, , ,5 24,3 32 M 2x1, , 78, , , 25,8 32 M 22x1, , 97, , ,5 29,6 36 M 24x , 122, , , 34,8 41 M 3x , 168, , , 37,7 5 M 36x , 26, , , 44,2 6 M 42x , 286, , , 55,9 65 M 48x , 485, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 size 5 turned from heat-treated alvanised steel to C45, Aisi 145 Free-cuttin steel to 9SMnPb28K, 12L13, with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54.! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 34

35 Rod Ends Series K - Maintenance Free Series GASW Rod End with male thread and PTFE liner For use at dynamic loads (D H7) B M A F L o G GL o Limitin speed rev/min 5 8 6, ,7 M ,3 7, , ,9 M , 9, , ,4 M , 16, , ,9 M ,4 23, , ,4 M ,5 32, , ,8 M , 42, , ,3 M , 52, , ,8 M 18x1, ,5 64, , ,3 M 2x1, , 78, , ,8 M 22x1, , 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 26, , ,2 M 42x , 286, , ,9 M 48x , 485, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 size 5 turned from heat-treated alvanised steel to C45, Aisi 145 Free-cuttin steel to 9SMnPb28K, 12L13, with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53).! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 35

36 Rod Ends Series K - Heavy duty - Maintenance Free Series GiXSW Rod End with female thread and PTFE liner For use at hih pressure and tension loads (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 6 9 6, , 8,9 11 M ,7 9, , ,5 1,4 13 M ,5 16, , , 12,9 17 M ,8 23, , ,5 15,4 19 M , 32, , , 16,8 22 M , 42, , , 19,3 22 M ,5 52, , , 21,8 27 M 18x1, ,5 64, , ,5 24,3 32 M 2x1, ,5 78, , , 25,8 32 M 22x1, , 97, , ,5 29,6 36 M 24x , 122, , , 34,8 41 M 3x , 168, , , 37,7 5 M 36x , 25, , , 44,2 6 M 42x2 6 27, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Heat-treated steel to 42CrMo4, Aisi 414, fored, alvanised Free-cuttin steel to 9SMnPB28K, 12L13, alvanised, with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae

37 Rod Ends Series K - Heavy duty - Maintenance Free Series GAXSW Rod End with male thread and PTFE liner For use at hih pressure and tension loads (D H7) B M A F L o G GL o Limitin speed rev/min 6 9 6, ,9 M ,8 9, , ,4 M ,5 16, , ,9 M ,4 23, , ,4 M , 32, , ,8 M , 42, , ,3 M , 52, , ,8 M 18x1, ,5 64, , ,3 M 2x1, ,5 78, , ,8 M 22x1, , 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 25, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Heat-treated steel to 42CrMo4, Aisi 414, fored, alvanised Free-cuttin steel to 9SMnPB28K, 12L13, alvanised, with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae

38 Rod Ends Series K - Stainless, Maintenance Free Series GiRSW Rod End with female thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 4 1) 7 5, ,5 7,8 6,5 8 M ,5 5, , , 9, 7,7 9 M ,8 7, , , 1, 8,9 11 M ,1 9, , , 12,5 1,4 13 M ,7 16, , , 15, 12,9 17 M ,3 23, , , 17,5 15,4 19 M ,5 32, , , 2, 16,8 22 M ,5 42, , , 22, 19,3 22 M ,5 52, , , 25, 21,8 27 M 18x1, , 64, , , 27,5 24,3 32 M 2x1, , 78, , , 3, 25,8 32 M 22x1,5 37 1, 97, , , 33,5 29,6 36 M 24x , 122, , , 4, 34,8 41 M 3x , 168, , , 46, 37,7 5 M 36x , 26, , , 57, 44,2 6 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 38

39 Rod Ends Series K - Stainless, Maintenance Free Series GARSW Rod End with male thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 4 1) 7 5, ,5 M ,5 5, , ,7 M ,2 7, , ,9 M ,8 9, , ,4 M ,1 16, , ,9 M ,5 23, , ,4 M ,5 32, , ,8 M ,5 42, , ,3 M ,5 52, , ,8 M 18x1, , 64, , ,3 M 2x1, , 78, , ,8 M 22x1,5 51 1, 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 26, , ,2 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 39

40 Rod Ends Series K - Stainless, Maintenance Free Series GiRSW..R Rod End with female thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 4 1) 7 5, ,5 7,8 6,5 8 M ,5 5, , , 9, 7,7 9 M ,8 7, , , 1, 8,9 11 M ,1 9, , , 12,5 1,4 13 M ,7 16, , , 15, 12,9 17 M ,3 23, , , 17,5 15,4 19 M ,5 32, , , 2, 16,8 22 M ,5 42, , , 22, 19,3 22 M ,5 52, , , 25, 21,8 27 M 18x1, , 64, , , 27,5 24,3 32 M 2x1, , 78, , , 3, 25,8 32 M 22x1,5 37 1, 97, , , 33,5 29,6 36 M 24x , 122, , , 4, 34,8 41 M 3x , 168, , , 46, 37,7 5 M 36x , 26, , , 57, 44,2 6 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Stainless steel 1.434, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 4

41 Rod Ends Series K - Stainless, Maintenance Free Series GARSW..R Rod End with male thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 4 1) 7 5, ,5 M ,5 5, , ,7 M ,2 7, , ,9 M ,8 9, , ,4 M ,1 16, , ,9 M ,5 23, , ,4 M ,5 32, , ,8 M ,5 42, , ,3 M ,5 52, , ,8 M 18x1, , 64, , ,3 M 2x1, , 78, , ,8 M 22x1,5 51 1, 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 26, , ,2 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Stainless steel 1.434, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 41

42 Rod Ends Series K - Stainless, Maintenance Free Series GiRSW..RR Rod End with female thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 4 1) 7 5, ,5 7,8 6,5 8 M ,5 5, , , 9, 7,7 9 M ,8 7, , , 1, 8,9 11 M ,1 9, , , 12,5 1,4 13 M ,7 16, , , 15, 12,9 17 M ,3 23, , , 17,5 15,4 19 M ,5 32, , , 2, 16,8 22 M ,5 42, , , 22, 19,3 22 M ,5 52, , , 25, 21,8 27 M 18x1, , 64, , , 27,5 24,3 32 M 2x1, , 78, , , 3, 25,8 32 M 22x1,5 37 1, 97, , , 33,5 29,6 36 M 24x , 122, , , 4, 34,8 41 M 3x , 168, , , 46, 37,7 5 M 36x , 26, , , 57, 44,2 6 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.434, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 42

43 Rod Ends Series K - Stainless, Maintenance Free Series GARSW..RR Rod End with male thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 4 1) 7 5, ,5 M ,5 5, , ,7 M ,2 7, , ,9 M ,8 9, , ,4 M ,1 16, , ,9 M ,5 23, , ,4 M ,5 32, , ,8 M ,5 42, , ,3 M ,5 52, , ,8 M 18x1, , 64, , ,3 M 2x1, , 78, , ,8 M 22x1,5 51 1, 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 26, , ,2 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.434, hardened, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 43

44 Rod Ends Series K - Stainless, Maintenance Free Series GiRSW..RR.316 Rod Ends with female thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 4 1) 7 5, ,5 7,8 6,5 8 M ,5 5, , , 9, 7,7 9 M ,8 7, , , 1, 8,9 11 M ,1 9, , , 12,5 1,4 13 M ,7 16, , , 15, 12,9 17 M ,3 23, , , 17,5 15,4 19 M ,5 32, , , 2, 16,8 22 M ,5 42, , , 22, 19,3 22 M ,5 52, , , 25, 21,8 27 M 18x1, , 64, , , 27,5 24,3 32 M 2x1, , 78, , , 3, 25,8 32 M 22x1,5 37 1, 97, , , 33,5 29,6 36 M 24x , 122, , , 4, 34,8 41 M 3x , 168, , , 46, 37,7 5 M 36x , 26, , , 57, 44,2 6 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.444, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 44

45 Rod Ends Series K - Stainless, Maintenance Free Series GARSW..RR.316 Rod End with male thread and PTFE liner For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 4 1) 7 5, ,5 M ,5 5, , ,7 M ,2 7, , ,9 M ,8 9, , ,4 M ,1 16, , ,9 M ,5 23, , ,4 M ,5 32, , ,8 M ,5 42, , ,3 M ,5 52, , ,8 M 18x1, , 64, , ,3 M 2x1, , 78, , ,8 M 22x1,5 51 1, 97, , ,6 M 24x , 122, , ,8 M 3x , 168, , ,7 M 36x , 26, , ,2 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: insert: Ball: Stainless steel to 1.457, Aisi 431, fored, polished size 4 turned from stainless steel to 1.457, Aisi 431 Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.444, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). 1) 4 on request. Housin turned from stainless steel to 1.435, Aisi 33! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 45

46 Rod Ends Series K - Stainless, Maintenance Free Series GiRSW..NiRo Rod End with female thread and PTFE liner bonded to the inner surface, completely in AISI 316 For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L K J o SW G GL o Limitin speed rev/min 4 1) 7 5, ,5 7,8 6,5 8 M ,7 5, , , 9, 7,7 9 M 5 1 7, 7, , , 1, 8,9 11 M ,5 9, , , 12,5 1,4 13 M ,5 16, , , 15, 12,9 17 M ,5 23, , , 17,5 15,4 19 M ,5 32, , , 2, 16,8 22 M , 42, , , 22, 19,3 22 M , 52, , , 25, 21,8 27 M 18x1, ,5 64, , , 27,5 24,3 32 M 2x1, ,5 78, , , 3, 25,8 32 M 22x1, , 97, , , 33,5 29,6 36 M 24x ,5 122, , , 4, 34,8 41 M 3x , 168, , , 46, 37,7 5 M 36x , 26, , , 57, 44,2 6 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: Stainless steel to 1.444, Aisi 316 insert: Ball: Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.444, Aisi316, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) on request! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 46

47 Rod Ends Series K - Stainless, Maintenance Free Series GARSW..NiRo Rod End with male thread and PTFE liner bonded to the inner surface, completely in AISI 316 For use at hih dynamic pressure and tension loads in corrosive environments (D H7) B M A F L o G GL o Limitin speed rev/min 4 1) 7 5, ,5 M ,7 5, , ,7 M ,5 7, , ,9 M ,5 9, , ,4 M , 16, , ,9 M , 23, , ,4 M , 32, , ,8 M , 42, , ,3 M , 52, , ,8 M 18x1, ,5 64, , ,3 M 2x1, ,5 78, , ,8 M 22x1, , 97, , ,6 M 24x ,5 122, , ,8 M 3x , 168, , ,7 M 36x ,5 26, , ,2 M 42x , 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht Housin: Stainless steel to 1.444, Aisi 316 insert: Ball: Stainless steel with PTFE liner bonded to the inner surface Stainless steel 1.444, Aisi316, round, polished This series is also available sealed (see pae 52) or with threaded bolt (see pae 53). Cetop connections see pae 54. 1) on request! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 47

48 Rod Ends Series K - Steel on Steel Series Gio Rod End with female thread, without the insert Hih axial load in one direction only. To be used only with limited oscillatin movements (D H7) B M A F L K J o SW G GL o Limitin speed rev/min Pivotin Anle a ( ) 5 8 6, , 7,7 9 M , 2, , , 8,9 11 M ,3 2, , ,5 1,4 13 M ,7 4,6 not to be , , 12,9 17 M ,8 6,5 used for , ,5 15,4 19 M , 8,5 complete , , 16,8 22 M ,5 11, revolutions , , 19,3 22 M , 14, , ,5 24,3 32 M 2x1, , 2, Weiht Housin: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, polished Cetop connections see pae 54. The base in the steel housin is cylindrically turned from one side and, startin from the centre line, it runs to suit the ball's contour (see drawin). Hence a hih axial load towards the turned radius is possible.! This series is not rereasable throuh rease nipple 48

49 Rod Ends Series K - Steel on Steel Series GAo Rod End with male thread, without the insert Hih axial load in one direction only. To be used only with limited oscillatin movements (D H7) B M A F L o G GL o Limitin speed rev/min Pivotin Anle a ( ) 5 8 6, ,7 M ,3 2, , ,9 M , 2, , ,4 M , 4,6 not to be , ,9 M ,4 6,5 used for , ,4 M ,5 8,5 complete , ,8 M ,5 11, revolutions , ,3 M ,5 14, , ,3 M 2x1, , 2, Weiht Housin: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, polished The base in the steel housin is cylindrically turned from one side and, startin from the centre line, it runs to suit the ball s contour (see drawin). Hence a hih axial load towards the turned radius is possible.! This series is not rereasable throuh rease nipple 49

50 Rod Ends Series K - Maintenance Free Series GioW Rod End with female thread, without the insert For use in applications involvin minimum axial loads and limited oscillatin movements (D H7) B M A F L K J o SW G GL o Limitin speed rev/min Pivotin Anle a ( ) 4 7 5, ,5 7,8 6,5 8 M ,2, , , 9, 7,7 9 M 5 1 9,8 1, , , 1, 8,9 11 M ,8 1,4 not to be , , 12,5 1,4 13 M ,3 2,2 used for , , 15, 12,9 17 M ,3 3,1 complete , , 17,5 15,4 19 M ,5 4, revolutions , , 2, 16,8 22 M , 5, , , 22, 19,3 22 M , 7, , , 27,5 24,3 32 M 2x1, , 9, Weiht Housin: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 with PTFE liner bonded to the inner surface Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, polished Cetop connections see pae 54. 5

51 Rod Ends Series K - Maintenance Free Series GAoW Rod End with male thread, without the insert For use in applications involvin minimum axial loads and limited oscillatin movements (D H7) B M A F L o G GL o Limitin speed rev/min Pivotin Anle a ( ) 4 7 5, ,5 M ,6, , ,7 M ,3 1, , ,9 M , 1,4 not to be , ,4 M , 2,2 used for , ,9 M ,4 3,1 complete , ,4 M ,5 4, revolutions , ,8 M , 5, , ,3 M ,5 7, , ,3 M 2x1, , 9, Weiht Housin: up to size 12 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 14 fored, from heat-treated alvanised steel to C22, M123 with PTFE liner bonded to the inner surface Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, polished 51

52 Rod Ends Series K - Sealed Version Series G...-2RS Sealed Rod Ends Series K in the followin versions: - G.S - G.XS - G.RS (..R) - G.SW - G.XSW - G.RSW (..R,..RR,..RR.316) D B M C o G Pivotin Anle α ( ) , 18, 1,5 M ,5 21, 12,5 M , 25,5 15,5 M ,5 29, 17, M , 32, 18,5 M , 38, 22, M 2x1,5 12 Rod Ends: 2RS seals: Retainers: See description of respective version NBR-Elastomer, temperature resistance -3 to +12 Celsius, resistant to mineral oils, rease and petrol Brass Spacers: Stainless steel to 1.435, Aisi 33 52

53 Rod Ends Series K - With Threaded Bolt Series G...-Bo Rod Ends and Spherical Plain Bearins with threaded bolt. For use as a riht anle connector: - G.S - G.XS - G.RS (..R) - G.SW - G.XSW - G.RSW (..R,..RR,..RR.316) L L1 GL G D SW Weiht of bolt 5 16, 5, 9 M 5 7, ,5 5,5 1 M 6 9, ,5 6,5 13 M 8 1, , 7, 17 M 1 13, ,5 7,5 2 M 12 15, ,5 8,5 22 M 14 17, ,5 9,5 24 M 16 19, , 12, 35 M 2 24, 22 2 Rod Ends and Sphericals: See description of respective version Threaded bolt: Free-cuttin steel to 9SMnPb28K, 12L13, zinc plated or stainless steel to 1.435, Aisi 33 53

54 Rod Ends Series K - CETOP Rod Ends for pneumatic cylinders to CETOP RP 13 P All female Rod Ends series are available with CETOP dimensions for pneumatic cylinders Connections to ISO 8139 (D) B M A F L K J o SW G GL o Limitin speed rev/min for cylinder-ø 5 8 6, , 7,7 9 M , , 8,9 11 M , ,5 1,4 13 M , , 12,9 17 M 1x1, , ,5 15,4 19 M 12x1, For load details , , 19,3 22 M 16x1, see previous paes , ,5 24,3 32 M 2x1, , ,5 29,6 36 M 24x , , 34,8 41 M 27x , , 37,7 5 M 36x , , 44,2 6 M 42x , , 55,9 65 M 48x See previous paes orderin Details: When orderin please specify Rod Ends series and thread, for example: GI 1x1,25 GISW 16x1,5 GIRSW 3 M27x2 54

55 Spherical Plain Bearins Series K - Standard Series GL Spherical Plain Bearins with outer rin, from freecuttin steel, zinc plated and rereasable Especially suited for axial loads (D H7) B M A (h6) o dk o Limitin speed rev/min 5 8 6, 16 7,7 11,11 1, 2, , ,9 12,7 12,8 3, , 22 1,4 15,87 21,6 5, , ,9 19,5 3, 7, , 3 15,4 22,22 4, 1, , ,8 25,4 51,5 13, , 38 19,3 28,57 64,5 16, , ,8 31,75 78,5 19, , 46 24,3 34,92 94,5 23, , 5 25,8 38,1 114, 29, , 56 29,6 42,86 142, 35, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: insert: Ball: Free-cuttin steel to 9SMnPb28K, 12L13, turned, alvanised Special brass to CuZn4AI1 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished 55

56 Spherical Plain Bearins Series K - Heavy Duty Series GLXS Spherical Plain Bearin, rereasable For use at hih revs (D H7) B M A (h6) o dk o Limitin speed rev/min 3 1) 2) 6 4,5 12 5,1 7,94 1,8 1, ) 2) 7 5, ,5 9,52 14,5 2, , 16 7,7 11,11 19,8 3, , ,9 12,7 25,8 4, , 22 1,4 15,87 42,6 7, , ,9 19,5 6, 1, , 3 15,4 22,22 8, 13, , ,8 25,4 12,5 17, , 38 19,3 28,57 128,5 21, , ,8 31,75 157, 26, , 46 24,3 34,92 188,5 31, , 5 25,8 38,1 229, 38, , 56 29,6 42,86 293, 47, , 66 34,8 5,8 381, 64, , 78 37,7 57,15 48, 8, , 87 44,2 65,96 693, 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: insert: Ball: Free-cuttin steel to 9SMnPb28K, 12L13, turned, alvanised Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) without lubrication hole 2) Outer Rin as one piece to CuSn8 56

57 Spherical Plain Bearins - corrosion protection class III, requirin maintenance Series GLRS Spherical Plain Bearin, rereasable For use at hih revs in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 3 1) 2) 6 4,5 12 5,1 7,94 1,8 1, , 16 7,7 11,11 19,8 3, , ,9 12,7 25,8 4, , 22 1,4 15,87 42,6 7, , ,9 19,5 6, 1, , 3 15,4 22,22 8, 13, , ,8 25,4 12,5 17, , 38 19,3 28,57 128,5 21, , ,8 31,75 157, 26, , 46 24,3 34,92 188,5 31, , 5 25,8 38,1 229, 38, , 56 29,6 42,86 293, 47, , 66 34,8 5,8 381, 64, , 78 37,7 57,15 48, 8, , 87 44,2 45,96 693, 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: insert: Ball: Stainless steel to 1.435, Aisi 33, turned Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface This series is also available with threaded bolt (see pae 53). 1) without lubrication hole 2) Outer Rin as one piece to CuSn8 57

58 Spherical Plain Bearins series K - stainless, requirin maintenance Series GLRS..R Spherical Plain Bearin, rereasable For use at hih revs in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 3 1) 2) 6 4,5 12 5,1 7,94 1,8 1, , 16 7,7 11,11 19,8 3, , ,9 12,7 25,8 4, , 22 1,4 15,87 42,6 7, , ,9 19,5 6, 1, , 3 15,4 22,22 8, 13, , ,8 25,4 12,5 17, , 38 19,3 28,57 128,5 21, , ,8 31,75 157, 26, , 46 24,3 34,92 188,5 31, , 5 25,8 38,1 229, 38, , 56 29,6 42,86 293, 47, , 66 34,8 5,8 381, 64, , 78 37,7 57,15 48, 8, , 87 44,2 45,96 693, 116, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: insert: Ball: Stainless steel to 1.435, Aisi 33, turned Special hih strenth bronze to CuSn8 Stainless steel Aisi42C, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) not rereasable throuh lubrication roove 2) Outer Rin as one piece to CuSn8 58

59 Spherical Plain Bearins Series K - Maintenance Free Series GLXSW Spherical Plain Bearin, maintenance free For use at hiher dynamic pressure and tension loads (D H7) B M A (h6) o dk o Limitin speed rev/min 4 1) 7 5, ,5 9,52 9,5 5, , 16 7,7 11,11 12,5 7, , ,9 12,7 15,5 9, , 22 1,4 15,87 27,8 16, , ,9 19,5 39, 23, , 3 15,4 22,22 53,5 32, , ,8 25,4 7, 42, , 38 19,3 28,57 88, 52, , ,8 31,75 16,5 64, , 46 24,3 34,92 13, 78, , 5 25,8 38,1 162, 97, , 56 29,6 42,86 24, 122, , 66 34,8 5,8 281, 168, , 78 37,7 57,15 343, 26, , 87 44,2 45,96 495, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: Free-cuttin steel to 9SMnPb28K, 12L13, turned, alvanised insert: Ball: Free-cuttin steel to 9SMnPb28K, turned, alvanised with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) Outer Rin as one piece to 45S2 59

60 Spherical Plain Bearins Series K - Stainless Outer Rin, Maintenance Free Series GLRSW Spherical Plain Bearin, maintenance free For use at hiher dynamic pressure and tension loads in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 4 1) 7 5, ,5 9,52 9,5 5, , 16 7,7 11,11 12,5 7, , ,9 12,7 15,5 9, , 22 1,4 15,87 27,8 16, , ,9 19,5 39, 23, , 3 15,4 22,22 53,5 32, , ,8 25,4 7, 42, , 38 19,3 28,57 88, 52, , ,8 31,75 16,5 64, , 46 24,3 34,92 13, 78, , 5 25,8 38,1 162, 97, , 56 29,6 42,86 24, 122, , 66 34,8 5,8 281, 168, , 78 37,7 57,15 343, 26, , 87 44,2 45,96 495, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: Stainless steel to 1.435, Aisi 33, turned insert: Ball: Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface This series is also available with threaded bolt (see pae 53). 1) Outer Rin stainless steel as one piece to 1.435, Aisi33 6

61 Spherical Plain Bearins Series K - Stainless, Maintenance Free Series GLRSW..R Spherical Plain Bearin, maintenance free For use at hiher dynamic pressure and tension loads in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 4 1) 7 5, ,5 9,52 9,5 5, , 16 7,7 11,11 12,5 7, , ,9 12,7 15,5 9, , 22 1,4 15,87 27,8 16, , ,9 19,5 39, 23, , 3 15,4 22,22 53,5 32, , ,8 25,4 7, 42, , 38 19,3 28,57 88, 52, , ,8 31,75 16,5 64, , 46 24,3 34,92 13, 78, , 5 25,8 38,1 162, 97, , 56 29,6 42,86 24, 122, , 66 34,8 5,8 281, 168, , 78 37,7 57,15 343, 26, , 87 44,2 45,96 495, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: Stainless steel to 1.435, Aisi 33, turned insert: Ball: Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Stainless steel to 1.434, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) Outer Rin stainless steel as one piece to 1.435, Aisi 33 61

62 Spherical Plain Bearins Series K - Stainless, Maintenance Free Series GLRSW..RR Spherical Plain Bearin, maintenance free For use at hiher dynamic pressure and tension loads in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 4 1) 7 5, ,5 9,52 9,5 5, , 16 7,7 11,11 12,5 7, , ,9 12,7 15,5 9, , 22 1,4 15,87 27,8 16, , ,9 19,5 39, 23, , 3 15,4 22,22 53,5 32, , ,8 25,4 7, 42, , 38 19,3 28,57 88, 52, , ,8 31,75 16,5 64, , 46 24,3 34,92 13, 78, , 5 25,8 38,1 162, 97, , 56 29,6 42,86 24, 122, , 66 34,8 5,8 281, 168, , 78 37,7 57,15 343, 26, , 87 44,2 45,96 495, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: Stainless steel to 1.435, Aisi 33, turned insert: Ball: Stainless steel to with PTFE liner bonded to the inner surface Stainless steel to 1.434, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) Outer Rin stainless steel as one piece to 1.435, Aisi 33 62

63 Spherical Plain Bearins Series K - Stainless, Maintenance Free Series GLRSW..RR.316 Spherical Plain Bearin, maintenance free For use at hiher dynamic pressure and tension loads in corrosive environments (D H7) B M A (h6) o dk o Limitin speed rev/min 4 1) 7 5, ,5 9,52 9,5 5, , 16 7,7 11,11 12,5 7, , ,9 12,7 15,5 9, , 22 1,4 15,87 27,8 16, , ,9 19,5 39, 23, , 3 15,4 22,22 53,5 32, , ,8 25,4 7, 42, , 38 19,3 28,57 88, 52, , ,8 31,75 16,5 64, , 46 24,3 34,92 13, 78, , 5 25,8 38,1 162, 97, , 56 29,6 42,86 24, 122, , 66 34,8 5,8 281, 168, , 78 37,7 57,15 343, 26, , 87 44,2 45,96 495, 286, only for short-term revolutions recommended Pivotin Anle a ( ) Weiht outer rin: Stainless steel to 1.435, Aisi 33, turned insert: Ball: Stainless steel with PTFE liner bonded to the inner surface Stainless steel to 1.444, Aisi 316 round, polished This series is also available with threaded bolt (see pae 53). 1) Outer Rin stainless steel as one piece to 1.435, Aisi 33 63

64 Spherical Plain Bearins Series K - Heavy Duty Series GXS Spherical Plain Bearin, rereasable For use at hih revs (D H7) B M A (h6) o dk 2 1) 4,5 3,6 6,5 2,6 5,2 6,6 1, ) 6, 4,5 9, 5,1 7,94 1,8 1, ) 7, 5,25 12, 6,5 9,52 14,5 2, ) 8, 6, 13, 7,7 11,11 19,8 3, , 6,75 15, 8,9 12,7 25,8 4, , 6,75 16, 8,9 12,7 25,8 4, , 9, 18, 1,4 15,87 42,6 7, , 9, 19, 1,4 15,87 42,6 7, , 1,5 21, 12,9 19,5 6, 1, , 1,5 22, 12,9 19,5 6, 1, , 12, 24,5 15,4 22,22 8, 13, , 12, 26, 15,4 22,22 8, 13, , 13,5 28, 16,8 25,4 12,5 17, , 13,5 29, 16,8 25,4 12,5 17, , 15, 31,5 19,3 28,57 128,5 21, , 15, 32, 19,3 28,57 128,5 21, , 16,5 34,5 21,8 31,75 157, 26, , 16,5 35, 21,8 31,75 157, 26, , 18, 38, 24,3 34,92 188,5 31, , 18, 4, 24,3 34,92 188,5 31, , 2, 41, 25,8 38,1 229, 38, , 2, 42, 25,8 38,1 229, 38, , 22, 46, 29,6 42,86 293, 47, , 22, 47, 29,6 42,86 293, 47, , 25, 54, 34,8 5,8 381, 64, , 25, 55, 34,8 5,8 381, 64, , 28, 62, 37,7 57,15 48, 8, , 28, 65, 37,7 57,15 48, 8, , 35, 72, 44,2 65,96 693, 116, , 35, 75, 44,2 65,96 693, 116, , 45, 9, 55,9 82, 11, 185, insert: Ball: Special hih strenth bronze to CuSn8 Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) without lubrication hole o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht 64

65 Spherical Plain Bearins Series K - Stainless Ball, requirin maintenance Series GXS..R Spherical Plain Bearin, rereasable For use at hih revs (D H7) B M A (h6) o dk 2 1) 4,5 3,6 6,5 2,6 5,2 6,6 1, ) 6, 4,5 9, 5,1 7,94 1,8 1, ) 7, 5,25 12, 6,5 9,52 14,5 2, ) 8, 6, 13, 7,7 11,11 19,8 3, , 6,75 15, 8,9 12,7 25,8 4, , 6,75 16, 8,9 12,7 25,8 4, , 9, 18, 1,4 15,87 42,6 7, , 9, 19, 1,4 15,87 42,6 7, , 1,5 21, 12,9 19,5 6, 1, , 1,5 22, 12,9 19,5 6, 1, , 12, 24,5 15,4 22,22 8, 13, , 12, 26, 15,4 22,22 8, 13, , 13,5 28, 16,8 25,4 12,5 17, , 13,5 29, 16,8 25,4 12,5 17, , 15, 31,5 19,3 28,57 128,5 21, , 15, 32, 19,3 28,57 128,5 21, , 16,5 34,5 21,8 31,75 157, 26, , 16,5 35, 21,8 31,75 157, 26, , 18, 38, 24,3 34,92 188,5 31, , 18, 4, 24,3 34,92 188,5 31, , 2, 41, 25,8 38,1 229, 38, , 2, 42, 25,8 38,1 229, 38, , 22, 46, 29,6 42,86 293, 47, , 22, 47, 29,6 42,86 293, 47, , 25, 54, 34,8 5,8 381, 64, , 25, 55, 34,8 5,8 381, 64, , 28, 62, 37,7 57,15 48, 8, , 28, 65, 37,7 57,15 48, 8, , 35, 72, 44,2 65,96 693, 116, , 35, 75, 44,2 65,96 693, 116, , 45, 9, 55,9 82, 11, 185, insert: Ball: Special hih strenth bronze to CuSn8 Stainless steel to 1.434, hardened, round, polished This series is also available with threaded bolt (see pae 53). 1) without lubrication hole o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht 65

66 Spherical Plain Bearins Series K - Maintenance Free Series GXSW Spherical Plain Bearin, maintenance free For use at hih pressure and dynamic loads D (H7) B M A (h6) o dk ,25 12, 6,5 9,52 8,5 5, , 13, 7,7 11,11 12,5 7, ,75 15, 8,9 12,7 15,5 9, ,75 16, 8,9 12,7 15,5 9, , 18, 1,4 15,87 27,8 16, , 19, 1,4 15,87 27,8 16, ,5 21, 12,9 19,5 39, 23, ,5 22, 12,9 19,5 39, 23, , 24,5 15,4 22,22 53,5 32, , 26, 15,4 22,22 53,5 32, ,5 28, 16,8 25,4 7, 42, ,5 29, 16,8 25,4 7, 42, , 31,5 19,3 28,57 88, 52, , 32, 19,3 28,57 88, 52, ,5 34,5 21,8 31,75 16,5 64, ,5 35, 21,8 31,75 16,5 64, , 38, 24,3 34,92 13, 78, , 4, 24,3 34,92 13, 78, , 41, 25,8 38,1 162, 97, , 42, 25,8 38,1 162, 97, , 46, 29,6 42,86 24, 122, , 47, 29,6 42,86 24, 122, , 54, 34,8 5,8 281, 168, , 55, 34,8 5,8 281, 168, , 62, 37,7 57,15 343, 26, , 65, 37,7 57,15 343, 26, , 72, 44,2 65,96 495, 286, , 75, 44,2 65,96 495, 286, , 9, 55,9 82, 8, 485, o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht insert: Ball: Free-cuttin steel to 9SMnPB28K, 12L13, alvanised, with PTFE liner bonded to inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished This series is also available with threaded bolt (see pae 53). 66

67 Spherical Plain Bearins Series K -Stainless Ball, Maintenance Free Series GXSW..R Spherical Plain Bearin, maintenance free For use at hih pressure and dynamic loads in corrosive environments D (H7) B M A (h6) o dk ,25 12, 6,5 9,52 8,5 5, , 13, 7,7 11,11 12,5 7, ,75 15, 8,9 12,7 15,5 9, ,75 16, 8,9 12,7 15,5 9, , 18, 1,4 15,87 27,8 16, , 19, 1,4 15,87 27,8 16, ,5 21, 12,9 19,5 39, 23, ,5 22, 12,9 19,5 39, 23, , 24,5 15,4 22,22 53,5 32, , 26, 15,4 22,22 53,5 32, ,5 28, 16,8 25,4 7, 42, ,5 29, 16,8 25,4 7, 42, , 31,5 19,3 28,57 88, 52, , 32, 19,3 28,57 88, 52, ,5 34,5 21,8 31,75 16,5 64, ,5 35, 21,8 31,75 16,5 64, , 38, 24,3 34,92 13, 78, , 4, 24,3 34,92 13, 78, , 41, 25,8 38,1 162, 97, , 42, 25,8 38,1 162, 97, , 46, 29,6 42,86 24, 122, , 47, 29,6 42,86 24, 122, , 54, 34,8 5,8 281, 168, , 55, 34,8 5,8 281, 168, , 62, 37,7 57,15 343, 26, , 65, 37,7 57,15 343, 26, , 72, 44,2 65,96 495, 286, , 75, 44,2 65,96 495, 286, , 9, 55,9 82, 8, 485, o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht insert: Ball: Special hih strenth bronze to CuSn8 with PTFE liner bonded to the inner surface Stainless steel to 1.434, hardened, round, polished This series is also available with threaded bolt (see pae 53). 67

68 Spherical Plain Bearins Series K -Stainless, Maintenance Free Series GXSW..RR Spherical Plain Bearin, maintenance free For use at hih pressure and dynamic loads in corrosive environments D (H7) B M A (h6) o dk ,25 12, 6,5 9,52 8,5 5, , 13, 7,7 11,11 12,5 7, ,75 15, 8,9 12,7 15,5 9, ,75 16, 8,9 12,7 15,5 9, , 18, 1,4 15,87 27,8 16, , 19, 1,4 15,87 27,8 16, ,5 21, 12,9 19,5 39, 23, ,5 22, 12,9 19,5 39, 23, , 24,5 15,4 22,22 53,5 32, , 26, 15,4 22,22 53,5 32, ,5 28, 16,8 25,4 7, 42, ,5 29, 16,8 25,4 7, 42, , 31,5 19,3 28,57 88, 52, , 32, 19,3 28,57 88, 52, ,5 34,5 21,8 31,75 16,5 64, ,5 35, 21,8 31,75 16,5 64, , 38, 24,3 34,92 13, 78, , 4, 24,3 34,92 13, 78, , 41, 25,8 38,1 162, 97, , 42, 25,8 38,1 162, 97, , 46, 29,6 42,86 24, 122, , 47, 29,6 42,86 24, 122, , 54, 34,8 5,8 281, 168, , 55, 34,8 5,8 281, 168, , 62, 37,7 57,15 343, 26, , 65, 37,7 57,15 343, 26, , 72, 44,2 65,96 495, 286, , 75, 44,2 65,96 495, 286, , 9, 55,9 82, 8, 485, o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht insert: Ball: Stainless steel to with PTFE liner bonded to the inner surface Stainless steel to 1.434, hardened, round, polished This series is also available with threaded bolt (see pae 53). 68

69 Spherical Plain Bearins Series K -Stainless, Maintenance Free Series GXSW..RR.316 Spherical Plain Bearin, maintenance free For use at hih pressure and dynamic loads in corrosive environments D (H7) B M A (h6) o dk ,25 12, 6,5 9,52 8,5 5, , 13, 7,7 11,11 12,5 7, ,75 15, 8,9 12,7 15,5 9, ,75 16, 8,9 12,7 15,5 9, , 18, 1,4 15,87 27,8 16, , 19, 1,4 15,87 27,8 16, ,5 21, 12,9 19,5 39, 23, ,5 22, 12,9 19,5 39, 23, , 24,5 15,4 22,22 53,5 32, , 26, 15,4 22,22 53,5 32, ,5 28, 16,8 25,4 7, 42, ,5 29, 16,8 25,4 7, 42, , 31,5 19,3 28,57 88, 52, , 32, 19,3 28,57 88, 52, ,5 34,5 21,8 31,75 16,5 64, ,5 35, 21,8 31,75 16,5 64, , 38, 24,3 34,92 13, 78, , 4, 24,3 34,92 13, 78, , 41, 25,8 38,1 162, 97, , 42, 25,8 38,1 162, 97, , 46, 29,6 42,86 24, 122, , 47, 29,6 42,86 24, 122, , 54, 34,8 5,8 281, 168, , 55, 34,8 5,8 281, 168, , 62, 37,7 57,15 343, 26, , 65, 37,7 57,15 343, 26, , 72, 44,2 65,96 495, 286, , 75, 44,2 65,96 495, 286, , 9, 55,9 82, 8, 485, o Limitin speed rev/min only for short-term revolutions recommended Pivotin Anle a ( ) Weiht insert: Ball: Stainless steel to with PTFE liner bonded to the inner surface Stainless steel to Aisi 316, round, polished This series is also available with threaded bolt (see pae 53). 69

70 Spherical Plain Bearins Series E - Maintenance Free Series GE...EC (-2RS) Spherical Plain Bearin, steel runnin on PTFE, maintenance free dk For use at hih unidirectional loads 7 (D) B M A o dk o o -2RS -2RS Pivotin Anle a ( ) Weiht 4 -, ,8 6, 8, 5,4-2, , ,8 8, 1, 9,1-3, , ,8 8, 1, 9,1-3, , ,8 1,2 13, 14, - 5, , ,9 13,2 16, 21, - 8, , ,9 14,9 18, 28, - 11, , ,9 18,4 22, 45, 59, 18, 17, , ,9 2,7 25, 56, 56, 22, 22, , ,9 2,7 25, 56, 75, 22, 22, , ,11 24,1 29, 78, 14, 31, 31, , ,11 29,3 35,5 127, 24, 51, 51, , ,11 34,2 4,7 166, 263, 65, 66, , ,13 39,7 47, 211, 338, 84, 14, , ,13 45, 53, 262, 419, 14, 185, , ,13 5,7 6, 337, 54, 135, 24, , ,13 55,9 66, 415, 665, 166, 295, , ,15 62,3 74, - 852, - 355, , ,15 66,8 8, - 13, - 46, , ,15 77,8 92, - 132, - 59, , ,15 89,4 15, - 17, - 75, , ,18 98,1 115, - 27, - 92, , ,18 19,5 13, - 257, , , ,25 121,2 14, - 277, - 123, , ,25 135,5 16, - 43, - 179, ) -, ,3 155,8 18, - 453, - 21, ) -, ,3 17,2 2, - 576, - 256, ) -, ,35 198,9 225, - 648, - 288, ) -, ,35 213,5 25, - 9, - 4, ) -, ,4 239,5 275, - 99, - 44, ) -, ,4 265,3 3, - 18, - 48, ) -, ,4 288,3 325, , - 57, ) -, ,4 313,8 35, , - 67, ) -, ,45 336,7 375, - 162, - 72, insert: Bearin steel to 1Cr6, Aisi 521, with PTFE liner, bonded to the inner surface 1) from size 14 the from size 15 available sealed from both sides (-2RS) hardened inserts are from size 35 only sealed from both sides (-2RS) two pieced and from size 4 to 5 when without seal, bearin steel C45/Aisi 145 with PTFE liner, bonded to the inner surface secured with tension Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, plished, hard chrome plated on the runnin surface sprin

71 Spherical Plain Bearins Series E - Stainless, Maintenance Free Series GE...EC-NiRo (-2RSF) Spherical Plain Bearin Series E, Maintenance Free dk For use at hih unidirectional loads in corrosive environments (D) B M A o dk 6 -, ,8 8, 1, 9, , ,8 1,2 13, 15, , ,9 13,2 16, 23, , ,9 14,9 18, 32, , ,9 18,4 22, 5, , ,9 2,7 25, 65, , ,9 2,7 25, 65, , ,11 24,2 29, 9, , ,11 29,3 35,5 159, , ,11 34,2 4,7 197, , ,13 39,8 47, 298, , ,13 45, 53, 37, , ,13 5,8 6, 481, , ,13 56, 66, 598, , ,15 66,8 8, 935, , ,15 77,9 92, 124, , ,15 89,4 15, 154, , ,18 98,1 115, 1892, , ,18 19,5 13, 2366, , ,25 121,2 14, 2548, ,5 16, 3752, ,2 -,25 o o -2RS -2RS Pivotin Anle a ( ) Weiht insert: Ball: Sealin: Stainless steel to , Aiso 316Ti, with PTFE liner bonded to the inner surface from size with hih performance PTFE compound from size 25 available sealed from both sides (-2RSF) Stainless steel to , Aisi 44C / , Aisi 44B, hardened, round, polished H Ecopur 71

72 Rod Ends Series E - Steel on Steel Series Ei (-2RS) Rod Ends with female thread made from freecuttin or heat-treated steel, zinc plated, with steel on steel Spherical Plain Bearins which require lubrication For use at hih multidirectional loads and limited fittin dimensions (D) B M A F L K J o SW G GL o Pivotin Anle a ( ) 6 6 4, , 13 1, 8, 11 M ,3 3, , , 16 12,5 1,2 14 M ,8 5, , , 19 15, 13,2 17 M ,4 8, , , 22 17,5 14,9 19 M , 1, , , 26 21, 18,4 22 M ,5 17, , , 3 24, 2,7 27 M ,5 21, , , 3 24, 2,7 27 M ,5 21, , , ,5 24,2 32 M 2x1,5 4 62,5 3, , , 42 33,5 29,3 36 M 24x , 48, , ,5 5 4, 34,2 41 M 3x , 62, , , 58 47, 39,8 5 M 36x , 8, , , 65 52, 45, 55 M 39x , 1, , , 65 52, 45, 55 M 42x ,5 99, , , 7 58, 5,8 6 M 42x , 127, , , 7 58, 5,8 6 M 45x , 127, , , 75 62, 56, 65 M 45x , 156, , , 75 62, 56, 65 M 52x , 156, , ,5 88 7, 66,8 75 M 52x3 7 45, 245, , ,5 88 7, 66,8 75 M 6x , 245, , , 98 8, 77,9 85 M 56x4 8 61, 315, , , 98 8, 77,9 85 M 72x4 8 36, 313, , , 11 95, 89,4 1 M 64x , 4, , , 11 95, 89,4 1 M 8x , 4, Weiht Housin: up to size 1 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 12 fored from heat-treated steel to C45, Aisi 145, alvanised Bearin: Steel on steel bearin GE...E, requirin lubrication (see pae 78) from size 15 available sealed from both sides (-2RS) from size 6 only available sealed from both sides (-2RS) Greasin: up to size 17 without lubrication fittin from size 2 fitted with hydraulic rease nipples to DIN

73 Rod Ends Series E - Steel on Steel Series EA (-2RS) Rod Ends with male thread made from freecuttin or heat-treated steel, zinc plated, with steel on steel Spherical Plain Bearins which require lubrication For use at hih multidirectional loads and limited fittin dimensions (D) B M A F L o G GL o Pivotin Anle a ( ) 6 6 4, , 8, M ,9 3, , , 1,2 M ,7 5, , , 13,2 M ,9 8, , , 14,9 M , 1, , , 18,4 M ,5 17, , , 2,7 M , 21, , , 2,7 M , 21, , ,5 24,2 M 2x1, ,5 3, , , 29,3 M 24x , 48, , ,5 34,2 M 3x , 62, , , 39,8 M 36x , 8, , , 45, M 39x , 1, , , 45, M 42x , 99, , , 5,8 M 42x , 127, , , 5,8 M 45x , 127, , , 56, M 45x , 156, , , 56, M 52x , 156, , ,5 66,8 M 52x , 245, , ,5 66,8 M 6x , 245, , , 77,9 M 56x , 315, , , 77,9 M 72x , 313, , , 89,4 M 64x , 4, , , 89,4 M 8x , 4, 6 12 Weiht Housin: up to size 1 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 12 fored from heat-treated steel to C45, Aisi 145, alvanised Bearin: Steel on steel bearin GE...E, requirin lubrication (see pae 78) from size 15 available sealed from both sides (-2RS) from size 6 only available sealed from both sides (-2RS) Greasin: up to size 17 without lubrication fittin from size 2 fitted with hydraulic rease nipples to DIN

74 Rod Ends Series E - Maintenance Free Series Ei..D (-2RS) Rod End Series E with female thread, and maintenance free Spherical Plain Bearin For use at hih unidirectional loads and limited fittin dimensions (D) B M A F L K J o SW G GL o o -2RS -2RS Pivotin Anle a ( ) Weiht 6 6 4, , 13 1, 8, 11 M ,3-3, , , 16 12,5 1,2 14 M ,8-5, , , 19 15, 13,2 17 M ,4-8, , , 22 17,5 14,9 19 M , - 11, , , 26 21, 18,4 22 M ,5 42,5 17, , , 3 24, 2,7 27 M ,5 54,5 22, , , 3 24, 2,7 27 M ,5 54,5 22, , , ,5 24,2 32 M 2x1,5 4 62,5 62,5 31, , , 42 33,5 29,3 36 M 24x , 92, 51, , ,5 5 4, 34,2 41 M 3x , 124, 66, , , 58 47, 39,8 5 M 36x , 144, 14, , , 65 52, 45, 55 M 39x , 18, 185, , , 65 52, 45, 55 M 42x ,5 12,5 14, , , 7 58, 5,8 6 M 42x , 24, 24, , , 7 58, 5,8 6 M 45x , 141, 135, , , 75 62, 56, 65 M 45x , 29, 295, , , 75 62, 56, 65 M 52x , 14, 166, , ,5 88 7, 66,8 75 M 52x3 7 45, 45, 46, , ,5 88 7, 66,8 75 M 6x , , , 98 8, 77,9 85 M 56x4 8 61, 61, 59, , , 98 8, 77,9 85 M 72x4 8-36, , , 11 95, 89,4 1 M 64x , 75, 75, , , 11 95, 89,4 1 M 8x , Housin: up to size 1 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 12 fored from heat-treated steel to C45, Aisi 145, alvanised Bearin: maintenance free steel/ptfe bearin GE EC (see pae 7) from size 15 available sealed from both sides (-2RS) from size 6 only available sealed from both sides (-2RS)! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 74

75 Rod Ends Series E - Maintenance Free Series EA..D (-2RS) Rod End Series E with male thread, and maintenance free Spherical Plain Bearin For use at hih unidirectional loads and limited fittin dimensions (D) B M A F L o G GL o o -2RS -2RS Pivotin Anle a ( ) 6 6 4, , 8, M ,9-3, , , 1,2 M ,7-5, , , 13,2 M ,9-8, , , 14,9 M , - 11, , , 18,4 M ,5 39,5 17, , , 2,7 M , 54, 22, , , 2,7 M , 54, 22, , ,5 24,2 M 2x1, ,5 62,5 31, , , 29,3 M 24x , 92, 51, , ,5 34,2 M 3x , 124, 66, , , 39,8 M 36x , 144, 14, , , 45, M 39x , 178, 185, , , 45, M 42x , 178, 14, , , 5,8 M 42x , 24, 24, , , 5,8 M 45x , 24, 135, , , 56, M 45x , 29, 295, , , 56, M 52x , 29, 166, , ,5 66,8 M 52x , 45, 46, , ,5 66,8 M 6x , , , 77,9 M 56x , 61, 59, , , 77,9 M 72x , , , 89,4 M 64x , 75, 75, , , 89,4 M 8x , Weiht Housin: up to size 1 turned, from free-cuttin steel to 9SMnPb28K, 12L13, alvanised from size 12 fored from heat-treated steel to C45, Aisi 145, alvanised Bearin: maintenance free steel/ptfe bearin GE EC (see pae 7) from size 15 available sealed from both sides (-2RS) from size 6 only available sealed from both sides (-2RS)! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 75

76 Rod Ends Series E - Stainless, Maintenance Free Series Ei..D-NiRo (-2RSF) Rod End Series E with female thread, maintenance free Spherical Plain Bearin GE..EC-NIRO (-2RSF) For use at hih unidirectional loads, in corrosive environments and limited fittin dimensions (D) B M A F L K J o SW G GL o o -2RS -2RS Pivotin Anle a ( ) 6 6 4, , 13 1, 8, 11 M , , , 16 12,5 1,2 14 M , , , 19 15, 13,2 17 M , , , 22 17,5 14,9 19 M , , , 26 21, 18,4 22 M , , , 3 24, 2,7 27 M , , , 3 24, 2,7 27 M , , , ,5 24,2 32 M 2x1,5 4 45, , , 42 33,5 29,3 36 M 24x , , ,5 5 4, 34,2 41 M 3x , , , 58 47, 39,8 5 M 36x , , , 65 52, 45, 55 M 39x , ) 32 27, , 7 58, 5,8 6 M 42x , , , 75 62, 56, 65 M 45x , ) 44 38, ,5 88 7, 66,8 75 M 52x , ) 49 42, , 98 8, 77,9 85 M 56x , ) 55 47, , 11 95, 89,4 1 M 64x , Weiht Housin: from size 6 to 4 stainless steel to 1.431, Aisi 34, fored, polished from size 45 stainless steel to 1.431, Aisi 34, turned from size 5 stainless steel to , Aisi 316Ti, turned Bearin: maintenance free stainless steel Spherical Plain Bearin GE EC-NIRO (-2RSF) (see pae 71) from size 25 available sealed from both sides (-2RS) 1) availability and price on request! Please note: The dynamic load "C" of the bearin of some rod ends is in some sizes hiher than the static load "C o " of the rod end. 76

77 Rod Ends Series E - Stainless, Maintenance Free Series EA..D-NiRo (-2RSF) Rod End with male thread, maintenance free, made from stainless steel with maintenance free Spherical Plain Bearins GE..EC-NIRO For use at hih unidirectional loads, in corrosive environments and limited fittin dimensions (D) B M A F L o G GL o o -2RS -2RS Pivotin Anle a ( ) 6 6 4, , 8, M , , , 1,2 M , , , 13,2 M , , , 14,9 M , , , 18,4 M , , , 2,7 M , , , 2,7 M , , ,5 24,2 M 2x1, , , , 29,3 M 24x , , ,5 34,2 M 3x , , , 39,8 M 36x , , , 45, M 39x , ) 32 27, , 5,8 M 42x , , , 56, M 45x , ) 44 38, ,5 66,8 M 52x , ) 49 42, , 77,9 M 56x , ) 55 47, , 89,4 M 64x , Weiht Housin: from size 6 to 4 stainless steel to 1.431, Aisi 34, fored, polished from size 45 stainless steel to 1.431, Aisi 34, turned from size 5 stainless steel to , Aisi 316Ti, turned Bearin: maintenance free stainless steel Spherical Plain Bearin GE EC-NIRO (-2RSF) (see pae 71) from size 25 available sealed from both sides (-2RS) 1) availability and price on request 77

78 Spherical Plain Bearins Series E - Steel on Steel Series GE...E (-2RS) Spherical Plain Bearins steel on steel, treated with molybdenum disulphide mos2, rereasable dk For use with hih multidirectional loads 78 B M A o dk 4 1) -, ,8 6, 8, 1, 2, ) -, ,8 8, 1, 17, 3, ) -, ,8 8, 1, 17, 3, ) -, ,8 1,2 13, 27,5 5, ) -, ,9 13,2 16, 4,5 8, ) -, ,9 14,9 18, 54, 1, , ,9 18,4 22, 85, 17, ) -, ,9 2,7 25, 16, 21, , ,9 2,7 25, 16, 21, , ,11 24,1 29, 146, 3, , ,11 29,3 35,5 24, 48, , ,11 34,2 4,7 31, 62, , ,13 39,7 47, 4, 8, , ,13 45, 53, 5, 1, , ,13 5,7 6, 64, 127, , ,13 55,9 66, 78, 156, , ,15 62,3 74, 1, 2, , ,15 66,8 8, 122, 245, , ,15 77,8 92, 156, 315, , ,15 89,4 15, 2, 4, , ,18 98,1 115, 245, 49, , ,18 19,5 13, 35, 61, , ,25 121,2 14, 325, 655, , ,25 135,5 16, 475, 95, , ,3 155,8 18, 54, 18, , ,3 17,2 2, 68, 137, , ,35 198,9 225, 765, 153, , ,35 213,5 25, 16, 212, , ,4 239,5 275, 116, 232, , ,4 265,3 3, 127, 255, , ,4 288,3 325, 153, 35, , ,4 313,8 35, 18, 355, ,7 375, 19, 38, ,35 -,45 insert: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated, treated with molybdenum disulphide from size 15 available sealed from both sides (-2RS) Ball: (D) from size 22 only available sealed from both sides (-2RS) Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated, treated with molybdenum disulphide o Pivotin Anle a ( ) Weiht 1) without lubrication hole 2) also available with outside diameter 28 mm

79 Spherical Plain Bearins - Steel on Steel Series GE...Ho-2RS Spherical Plain Bearins steel on steel, rereasable with lip seal on both sides. Dimensions identical to series GE...E (-2RS) but ball with shoulder Throuh the ball with shoulder no distance rins are required dk (D) B M A o dk 16 2) -, ,9 21, 25, 16 21, , ,9 21, 25, 16 21, , ,11 24, 29, 146 3, , ,11 29, 35, , , ,11 34,2 4, , , ,13 4, 47, 4 8, , ,13 45, 53, 5 1, , ,13 51,5 6, , , ,13 56,5 66, , , ,15 67,7 8, , , ,15 78, 92, , , ,15 9, 15, 2 4, ) -, ,18 99, 115, , ) -, ,18 113, 13, 33 67, ) , 16, , ,2 insert: -,25 o Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide Pivotin Anle a ( ) Weiht Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 1) Price and availability on request 2) without -2RS seals 79

80 Spherical Plain Bearins Series E- Steel on Steel - inch-sized Series GE..Zo (-2RS) Steel on Steel Spherical Plain Bearin, requirin maintenance, inch-sized dk For use with hih multidirectional loads D B M A dk o Pivotin Anle a ( ) Weiht 12 12,7 -,8 11,1 9,525 22,225 -,9 18,,5,437,375,875, ,875 -,8 13,894 11,913 26,988 -,9 23,,625,547,469 1,625, ,5 -,1 16,662 14,275 31,75 -,11 27,5,75,656,562 1,25 1, ,225 -,1 19,431 16,662 36,513 -,11 32,,875,765,656 1,4375 1, ,4 -,1 22,225 19,5 41,275 -,11 36,5 1,,875,75 1,625 1, ,75 -,12 27,762 23,8 5,8 -,13 45,5 1,25 1,93,937 2, 1, ,925 -,12 3,15 26,187 55,563 -,13 49, 1,375 1,187 1,31 2,1875 1, ,1 -,12 33,325 28,575 61,913 -,13 54,7 1,5 1,312 1,125 2,4375 2, ,45 -,12 38,887 33,325 71,438 -,13 63,9 1,75 1,531 1,312 2,8125 2, ,8 -,15 44,45 38,1 8,963 -,15 73, 2, 1,75 1,5 3,1875 2, ,15 -,15 5,13 42,85 9,488 -,15 82, 2,25 1,969 1,687 3,5625 3, ,5 -,15 55,55 47,625 1,13 -,15 92, 2,5 2,187 1,875 3,9375 3, ,85 -,15 61,112 52, ,125 -,15 1, 2,75 2,46 2,62 4,375 3, ,2 -,15 66,675 57,15 12,65 -,18 19,5 3, 2,625 2,25 4,75 4, ,55 -,2 72,238 61,9 13,175 -,18 119, 3,25 2,844 2,437 5,125 4, ,9 -,2 77,775 66, ,7 -,18 128, 3,5 3,62 2,625 5,5 5, ,25 -,2 83,337 71, ,225 -,15 137, 3,75 3,281 2,812 5,875 5,

81 Spherical Plain Bearins Series E- Steel on Steel - inch-sized D B M A dk o Pivotin Anle a ( ) Weiht 11 11,6 -,2 88,9 76,2 158,75 -,25 146, 4, 3,5 3, 6,25 5, ,95 -,2 94,463 8,95 168,275 -,25 155, 4,25 3,719 3,187 6,625 6, ,3 -,2 1,13 85, ,8 -,25 164,5 4,5 3,937 3,375 7, 6, ,65 -,25 15,562 9, ,325 -,3 173,5 4,75 4,156 3,562 7,375 6, , -,25 111,125 95,25 196,85 -,3 183, 5, 4,375 3,75 7,75 7, ,4 -,25 12,65 14, ,25 -,3 27, 6, 4,75 4,125 8,75 8, ,1 -,25 123,825 13, ,65 -,3 223, 6,5 4,875 4,62 9,75 8, ,8 -,25 133,35 111, ,7 -,35 24, 7, 5,25 4,375 1,5 9, ,5 -,3 142, ,5 285,75 -,35 257, 7,5 5,625 4,687 11,25 1, ,5 -,3 152,4 127, 34,8 -,35 275, 8, 6, 5, 12, 1, ,9 -,3 161, , ,85 -,4 292, 8,5 6,375 5,312 12,75 11, ,6 -,3 171,45 142,75 342,9 -,4 39, 9, 6,75 5,625 13,5 12, ,3 -,3 18,975 15,8 361,95 -,4 326, 9,5 7,125 5,937 14,25 12, , -,35 19,5 158,75 381, -,4 343, 1, 7,5 6,25 15, 13, ,7 -,35 2,25 166,675 4,5 -,45 36, 1,5 7,875 6,562 15,75 14, ,4 -,35 29,55 174, ,1 -,45 377, 11, 8,25 6,875 16,5 14, ,1 -,35 219,75 182,55 438,15 -,45 395, 11,5 8,625 7,187 17,25 15, ,8 -,35 288,6 19,5 457,2 -,45 412, 12, 9, 7,5 18, 16, insert: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide from size 19 available sealed from both sides (-2RS) Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 81

82 Spherical Plain Bearins Series W - Steel on Steel Series GE...Lo Spherical Plain Bearins steel on steel series W to DIN ISO , treated with molybdenum disulphide mos2, rereasable For use on standard Hydraulic Cylinders to DIN and to DIN with floor piece or piston rod relays dk (D) B M A o dk 12 1) +, ,9 15,5 18, 54 1, , ,9 18,5 22, 84 16, , ,9 2, 23, 88 17, , ,11 21, 25, 16 21, , ,11 25, 29, 146 3, , ,11 3,5 35, , , ,11 34, 4, , , ,13 37, 43, , , ,13 4, 47, , , ,13 46, 53, 5 1, , ,13 52, 6, , , ,13 57, 66, , , ,15 68, 8, , , ,15 71,5 83, , , ,15 79, 92, , , ,15 91, 15, 2 4, , ,18 99, 115, , , ,18 113, 13, 35 61, , ,25 124, 14, , , ,25 138, 16, , , ,3 177, 2, , , ,35 221, 25, , , ,4 317, 35, , , 45, 35 61, ,57 -,5 o Pivotin Anle a ( ) Weiht insert: Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 1) lubrication roove in the insert only 82

83 Spherical Plain Bearins Series G - Steel on Steel Series GE...Fo (-2RS) Spherical Plain Bearins steel on steel series G to DIN ISO Treated with molybdenum disulphide mos2, rereasable dk For use with hiher pivotin anle (D) B M A o dk 4 1) -, ,8 7,1 1, 17, 3, ) -, ,8 9,3 13, 27, 5, ) -, ,8 9,3 13, 27,5 5, ) -, ,9 11,6 16, 4,5 8, ) -, ,9 13,4 18, 54, 1, ) -, ,9 16, 22, 85, 17, , ,9 19,2 25, 16, 21, , ,11 21, 29, 146, 3, , ,11 25,2 35,5 24, 48, , ,11 29,5 4,7 31, 62, , ,13 34,4 47, 4, 8, , ,13 39,7 53, 5, 1, , ,13 44,7 6, 64, 127, , ,13 5, 66, 78, 156, , ,15 57,1 8, 122, 245, , ,15 67, 92, 156, 315, , ,15 78,2 15, 2, 4, , ,18 87,1 115, 245, 49, , ,18 98,3 13, 35, 61, , ,25 111,2 14, 325, 655, , ,25 124,8 16, 475, 95, , ,3 138,4 18, 54, 18, , ,3 151,9 2, 68, 137, , ,35 18, 225, 765, 153, , ,35 196,1 25, 16, 212, , ,4 22, 275, 116, 232, , ,4 243,6 3, 127, 255, , ,4 263,6 325, 153, 35, , ,4 283,6 35, 18, 355, ,6 375, 19, 38, ,35 -,45 o Pivotin Anle a ( ) Weiht insert: Ball: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide from size 15 available sealed from both sides (-2RS) Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 1) without lubrication hole 83

84 Spherical Plain Bearins Series G - Maintenance Free Series GE...FW (-2RS) Spherical Plain Bearins series G to DIN ISO Matin surface hard chromium/ptfe, maintenance free dk Hiher pivotin anle throuh wider ball B M A o dk 4 -, ,8 7,1 1, 9,1-3, , ,8 9,3 13, 14, - 5, , ,8 9,3 13, 14, - 5, , ,9 11,6 16, 21, - 8, , ,9 13,4 18, 28, - 11, , ,9 16, 22, 45, - 18, , ,9 19,2 25, 56, 75, 22, 32, , ,11 21, 29, 78, 14, 31, 45, , ,11 25,2 35,5 127, 24, 51, 85, , ,11 29,5 4,7 166, 263, 65, 11, , ,13 34,4 47, 211, 338, 84, 14, , ,13 39,7 53, 262, 419, 14, 175, , ,13 44,7 6, 337, 54, 135, 225, , ,13 5, 66, 415, 665, 166, 275, , ,15 57,1 8, - 13, - 43, , ,15 67, 92, - 132, - 55, , ,15 78,2 15, - 17, - 75, , ,18 87,1 115, - 27, - 86, , ,18 98,3 13, - 257, - 17, , ,25 111,2 14, - 277, - 115, , ,25 124,8 16, - 43, - 168, , ,3 138,4 18, - 453, - 189, ) -, ,3 151,9 2, - 576, - 24, ) -, ,35 18, 225, - 648, - 27, ) -, ,35 196,1 25, - 9, - 375, ) -, ,4 22, 275, - 99, - 412, ) -, ,4 243,6 3, - 18, - 45, ) -, ,4 263,6 325, , - 536, ) -, ,4 283,6 35, , - 63, ) ,6 375, - 162, - 675, ,35 -,45 insert: Bearin steel with PTFE liner bonded to the inner surface from size 15 available sealed (-2RS) on both sides from size 35 only available sealed (-2RS) on both sides Ball: (D) o o -2RS Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated on the runnin surface -2RS Pivotin Anle a ( ) Weiht 1) from size 12 the hardened inserts are two pieced and secured with tension sprin 84

85 Spherical Plain Bearin Series G - Stainless, maintenance free Series GE...FW-NiRo (-2RS) Spherical Plain Bearin Series G, Matin surface NIRO/PTFE, maintenance free dk Increased Pivotin Anle throuh a wide ball (D) B M A o dk 4 -, ,8 7,1 1, 9, , ,8 9,3 13, 15, , ,8 9,3 13, 15, , ,9 11,6 16, 23, , ,9 13,4 18, 32, , ,9 16, 22, 5, , ,9 19,2 25, 65, , ,11 21, 29, 9, , ,11 25,2 35,5 159, , ,11 29,5 4,7 197, , ,13 34,4 47, 298, , ,13 39,7 53, 37, , ,13 44,7 6, 481, , ,13 5, 66, 598, , ,15 57,1 8, 935, , ,15 67, 92, 124, , ,15 78,2 15, 154, , ,18 87,1 115, 1892, , ,18 98,3 13, 2366, , ,25 111,2 14, 2548, ,8 16, 3752, ,2 -,25 o o -2RS -2RS Pivotin Anle a ( ) Weiht insert: Ball: Sealin: Stainless steel to , Aiso 316Ti, with PTFE liner bonded to the inner surface from size 8 with hih performance PTFE compound from size 2 available sealed from both sides (-2RSF) Stainless steel to 1.434, hardened, round, polished H-Ecopur 85

86 Anular Contact Spherical Plain Bearins - Steel on Steel Series GE...SX Anular Contact Spherical Plain Bearins steel on steel. Treated with molybdenum disulphide mos2, rereasable M1 S dk r1s For use at unidirectional, dynamic radial and additional axial loads rs T (D) -,12 -,12 -,12 -,12 -,12 -,12 -,12 -,12 -,15 -,15 -,15 -,15 -,15 -,15 -,2 -,2 -,2 -,2 -,2 -,2 -,2 -,25 -,25 -,25 -,25 -,25 -,25 -,3 -,3 r B M A T S M1 s, r 1s d min k , 47 15,6 7,5 1, 42, , , , 8, 1, 47, 3 6 2, , ,3 8,5 1, 49, , , , 8,5 1, 52, , , ,1 9, 1, 55, , , ,8 9,5 1, 62, , , ,5 1, 1, 68, , , 8 2 4,3 1, 1, 74, , , , 11,5 1,1 82, , , ,7 11,5 1,1 88, , , ,5 11,5 1,1 93, , , ,2 12,5 1,1 12, , , ,9 12,5 1,1 17, , , ,6 14,5 1,1 115, , , ,4 14,5 1,1 122, , , ,1 16, 1,5 128, , , ,8 16, 1,5 135, , , ,6 16, 1,5 141, , ) 35 32, ,3 17,5 2, 148, , ) 38 34, , 19, 2, 155, , ) 38 37, ,5 19, 2, 168, , ) 45 43, , 19, 2,5 188, , ) 45 43, , 19, 2,5 198, , ) 48 46, , 2,5 3, 211, , ) 51 49, , 22, 3, 225, , ) 57 55, , 27, 3, 246, , ) 64 61, , 28, 3, 26, , ) 64 62, , 3, 3, 275, 75 15, ) 7 66, , 3, 3, 29, , ,14 -,16 -,16 -,16 -,16 -,16 -,16 -,16 -,18 -,18 -,18 -,18 -,18 -,2 -,2 -,2 -,2 -,2 -,25 -,25 -,25 -,3 -,3 -,3 -,3 -,35 -,35 -,35 -,35 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,8 +,35 -,8 Radial Load C o C Pivotin Anle a ( ) Weiht Housin disk: inner disk: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 1) Price and availability on request 86

87 Anular Contact Spherical Plain Bearins - Maintenance Free Series GE...SW Anular Contact Spherical Plain Bearins. Matin surface hard chromium/ptfe, maintenance free S dk r1s For use at unidirectional, dynamic radial and additional axial loads rs T (D) -,12 -,12 -,12 -,12 -,12 -,12 -,12 -,12 -,15 -,15 -,15 -,15 -,15 -,15 -,2 -,2 -,2 -,2 -,2 -,2 -,2 -,2 -,2 -,25 -,25 -,25 -,25 -,3 -,3 r B M A T S s, r 1s d min k , 47 15,6 1, 42, , , , 1, 47, , , ,3 1, 49, , , , 1, 52, , , ,1 1, 55, , , ,8 1, 62, , , ,5 1, 68, , , 8 2 4,3 1, 74, , , , 1,1 82, , , ,7 1,1 88, , , ,5 1,1 93, , , ,2 1,1 12, , , ,9 1,1 17, , , ,6 1,1 115, , , ,4 1,1 122, , , ,1 1,5 128, , , ,8 1,5 135, , , ,6 1,5 141, , ) 35 32, ,3 2, 148, , ) 38 34, , 2, 155, , ) 38 37, ,5 2, 168, , ) 45 43, , 2,5 188, , ) 45 43, , 2,5 198, , ) 48 46, , 3, 211, , ) 51 49, , 3, 225, , ) 57 55, , 3, 246, , ) 64 61, , 3, 26, , ) 64 62, , 3, 275, , ) 7 66, , 3, 29, ,5 238 Housin disk: inner disk: on request: -,14 -,16 -,16 -,16 -,16 -,16 -,16 -,16 -,18 -,18 -,18 -,18 -,18 -,2 -,2 -,2 -,2 -,2 -,2 -,2 -,25 -,25 -,25 -,3 -,3 -,35 -,35 -,35 -,35 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,25 -,6 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,8 +,35 -,8 Bearin steel to 1Cr6, Aisi 521, hardened with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated Stainless steel version 1) Price and availability on request Radial Load C o C Pivotin Anle a ( ) Weiht 87

88 D1 Spherical Plain Thrust Bearins - Steel on Steel Series GE...AX Spherical Plain Thrust Bearins steel on steel. Treated with molybdenum disulphide mos2, rereasable M1 S r1s dk d1 rs T For use at axial loads (D) -,8 -,8 -,8 -,8 -,1 -,1 -,1 -,12 -,12 -,12 -,12 -,15 -,15 -,15 -,2 -,2 -,25 -,25 -,25 -,3 r B M A T S M1 s, r 1s d 1 D 1 d min max min k 1 7,5 7, 3 9,5 7, 3,,6 27,5 15, ,5 9, , 8, 4,,6 32, 18, , 1, , 1, 5,,6 39, 22, ,8 11, , 11, 5,,6 43,5 27, ,5 13,8 55 2, 12,5 6, 1, 5, 31, ,5 16, ,5 14, 6, 1, 58,5 34, , 19, 75 26, 17,5 8, 1, 7, 42, , 2,7 9 28, 22, 8, 1, 84, 5, , 21, , 24,5 9, 1, 97, 59, , 25, ,5 27,5 11, 1, 11, 67, , 3, ,5 3, 1, 1, 12, 7, , 34, 15 45, 35, 12,5 1, 14, 84, , 36,5 16 5, 35, 13,5 1, 153, 94, ,5 38, 18 5, 42,5 14,5 1, 172, 17, , 46, 21 59, 45, 15, 1,1 198, 127, ) 53,5 5, 23 64, 52,5 16,5 1,1 22, 145, ) 61, 54, 26 72, 52,5 23, 1,5 243, 177, ) 66, 58, 29 77, 65, 23, 1,5 271, 2, ) 74, 62, 32 86, 67,5 26, 1,5 299, 225, ) 8, 66, 34 87, 7, 27, 1,5 32, 247, ,9 -,11 -,11 -,11 -,13 -,13 -,13 -,15 -,15 -,15 -,18 -,18 -,25 -,25 -,3 -,3 -,35 -,35 -,4 -,45 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,6 +,25 -,6 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,8 Axiale load C o C Pivotin Anle a ( ) Weiht Housin disk: inner disk: Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide Bearin steel to 1Cr6, Aisi 521, hardened, round, phosphated treated with molybdenum disulphide 1) Price and availability on request 88

89 D1 Spherical Plain Thrust Bearins - Maintenance Free Series GE...AW Spherical Plain Thrust Bearins. Matin surface hard chromium/ptfe, maintenance free S r1s dk d1 rs T For use with axial loads (D) -,8 -,8 -,8 -,8 -,1 -,1 -,1 -,12 -,12 -,12 -,12 -,15 -,15 -,15 -,2 -,2 -,25 -,25 -,25 -,3 -,3 -,3 -,35 -,35 -,35 -,4 -,4 -,4 r B M A T S s, r 1s d 1 D 1 d min max min k 1 7,5 7, 3 9,5 7,,6 27,5 15, , ,5 9, , 8,,6 32, 18, , , 1, , 1,,6 39, 22, , ,8 11, , 11,,6 43,5 27, , ,5 13,8 55 2, 12,5 1, 5, 31, , ,5 16, ,5 14, 1, 58,5 34, , , 19, 75 26, 17,5 1, 7, 42, , , 2,7 9 28, 22, 1, 84, 5, , , 21, , 24,5 1, 97, 59, , , 25, ,5 27,5 1, 11, 67, , , 3, ,5 3, 1, 12, 7, , , 34, 15 45, 35, 1, 14, 84, , , 36,5 16 5, 35, 1, 153, 94, , ,5 38, 18 5, 42,5 1, 172, 17, , , 46, 21 59, 45, 1,1 198, 127, , ) 53,5 5, 23 64, 52,5 1,1 22, 145, , ) 61, 54, 26 72, 52,5 1,5 243, 177, , ) 66, 58, 29 77, 65, 1,5 271, 2, , ) 74, 62, 32 86, 67,5 1,5 299, 225, , ) 8, 66, 34 87, 7, 1,5 32, 247, , ) 82, 67, 37 97, 75, 1,5 35, 265, , ) 87, 73, 4 13, 77,5 1,5 382, 294, , ) 95, 8, , 82,5 1,5 49, 317, , ) 1, 85, 46 11, 8, 3, 445, 337, , ) 1, 9, 48 11, 8, 3, 46, 356, , ) 15, 91, , 95, 4, 5, 38, , ) 15, 91, , 95, 4, 51, 38, , ) 115, 95, , 95, 4, 535, 4, , 132 -,9 -,11 -,11 -,11 -,13 -,13 -,13 -,15 -,15 -,15 -,18 -,18 -,25 -,25 -,3 -,3 -,35 -,35 -,4 -,4 -,4 -,4 -,45 -,45 -,45 -,5 -,5 -,5 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,4 +,25 -,5 +,25 -,5 +,25 -,5 +,25 -,6 +,25 -,6 +,35 -,7 +,35 -,7 +,35 -,7 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 +,35 -,8 Axiale load C o C Pivotin Anle a ( ) Weiht Housin disk: inner disk: on request: Bearin steel to 1Cr6, Aisi 521, hardened with PTFE liner bonded to the inner surface Bearin steel to 1Cr6, Aisi 521, hardened, round, polished, hard chrome plated Stainless steel version 1) Price and availability on request 89

90 Hydraulic Rod Ends to DIN / ISO 8133 Series FPR...S Rod Ends, fastened by hexaon socket head cap screw to DIN Spherical Plain Bearins, rereasable, fixed throuh caulkin on both sides For use in standard Hydraulic Cylinders 16 bar to ISO 62/2 M1 (D) B M M1 A F L K J G GL , 4 17 M 1x1, , 1, , M 12x1, ,5 21, , M 14x1, ,5 3, , 62 3 M 16x1, , 48, , M 2x1, , 62, , 9 45 M 27x , 1, , M 33x , 156, , M 42x , 245, , M 48x , 4, , M 64x , 61, Torque Nm Housin: up to size 5 fored from heat-treated steel to C45, Aisi 145 from size 6 made from nodular cast iron GS 4 o Pivotin Anle a ( ) Weiht Bearin: Greasin: on request: Steel on steel bearin GE...E, requirin lubrication 12 is not rereasable über Schmiernippel from size 16-2 fitted with rease hole in housin from size 25 fitted with hydraulic rease nipples to DIN with left hand thread (FPL...S) 9

91 Hydraulic Rod Ends to DIN / ISO 6982 Series FPR...CE Rod Ends Cetop, recommendation RP 58H for standard Hydraulic Cylinders, fastened by hexaon socket head cap screws to DIN Spherical Plain Bearins, rereasable, fixed with snap rins M1 Mountin dimensions to DIN and ISO 62/1, ISO 622 (D) B M M1 A F L K J G , 15, 32, 38 54, M 12x1, ,5 1, , 15, 4, 44 64, 4 21 M 14x1, ,5 17, , 19, 47, 52 77, M 16x1, , 3, , 19, 58, 65 96, 54 3 M 2x1, , 48, , 22, 71, 8 118, M 27x , 67, , 26, 9, , 8 47 M 33x , 1, , 32, 19, , M 42x , 156, , 38, 136, , M 48x , 255, , 42, 155, , M 56x , 315, , 48, 17, 18 27, M 64x , 4, , 52, 185, , 16 1 M 72x , 49, , 62, 211, , M 8x , 61, , 62, 235, , M 9x , 655, , 72, 265, 26 46, M 1x , 95, , 82, 326, , M 125x , 137, , 12, 418, 39 62, M 16x , 212, GL Torque Nm o Pivotin Anle a ( ) Weiht Housin: up to size 63 fored from heat-treated steel to C45, Aisi 145 from size 7 made from nodular cast iron GS 4 Bearin: Steel on steel bearin GE..LO (see pae 82) Greasin: on request: size 12 is not rereasable über Schmiernippel from size 16 fitted with hydraulic rease nipples to DIN with left hand thread (FPL...CE) 91

92 Hydraulic Rod Ends Series FPR...N Rod Ends with short thread, particular suited for Hydraulic Cylinders. Spherical Plain Bearins, rereasable, fixed with snap rins For use with shortest relay distances and maximum stroke utilization M1 (D) B M M1 A F L K J G GL o Pivotin Anle a ( ) Weiht , M 16x1, , , M 16x1, , , 5 32 M 22x1, , , 66 4 M 28x1, , , M 35x1, , , 9 61 M 45x1, , , M 58x1,5 59 4, , M 65x1, , , M 8x , , M 1x , , M 11x , , M 12x , , M 13x , Housin: up to size 8 fored from heat-treated steel to C45, Aisi 145 from size 9 made from nodular cast iron GS 4 Bearin: Steel on steel bearin GE E, requirin maintenance (see pae 78) Greasin: fitted with hydraulic rease nipples to DIN on request: with left hand thread (FPL...N) 92

93 Hydraulic Rod Ends Series FPR...u Rod Ends identical with FPR...N, in addition fastened by hexaon socket head cap screws to DIN Spherical Plain Bearins, rereasable, fixed with snap rins M1 For use with shortest relay distances and maximum stroke utilization (D) B M M1 A F L K J G , M 16x1, , , M 16x1, , , 5 32 M 22x1, , , 66 4 M 28x1, , , M 35x1, , , 9 61 M 45x1, , , M 58x1, , , M 65x1, , , M 8x , , M 1x , , M 11x , , M 12x , , M 13x , GL Torque Nm o Pivotin Anle a ( ) Weiht Housin: up to size 8 fored from heat-treated steel to C45, Aisi 145 from size 9 made from nodular cast iron GS 4 Bearin: Steel on steel bearin GE E, requirin maintenance (see pae 78) On request also available with Spherical Plain Bearin GE LO (see pae 82) Greasin: fitted with hydraulic rease nipples to DIN on request: with left hand thread (FPL...U) 93

94 Hydraulic Rod Ends Series FMA...D Rod Ends fastened by hexaon socket head cap screws to DIN Spherical Plain Bearins, rereasable, fixed with snap rins For use with double action Hydraulic Cylinders (D) B M A F L K J G GL Torque Nm o Pivotin Anle a ( ) Weiht M 18x M 24x M 3x M 39x M 5x M 64x M 8x M 9x M 1x M 11x M 12x M 15x M 16x M 18x Housin: Bearin: Greasin: on request: Nodular cast iron GS4 Steel on steel bearin GE...E, requirin lubrication size 25 without lubrication fittin, but fitted with rease hole in housin from size 3 fitted with hydraulic rease nipples to DIN with left hand thread (FMAL...D) 94

95 Hydraulic Rod Ends - Weld-On Base Series FS...C Rod Ends series E to DIN ISO , type S with circular surface for weld-on. Spherical Plain Bearins, rereasable, fixed throuh caulkin on both sides 45¼ For Weld-on to piston Rod Ends L1 6 (D) B M A F L L1 K J o Pivotin Anle a ( ) ,5 1,5 15, 3 15,6 8, , 1,5 17,5 3 21,6 1, , 2, 21, 4 32, 17, , 2, 24, 4 4, 21, ,5 2, 27,5 4 54, 3, , 3, 33,5 4 72, 48, ,5 3, 4, 4 95, 62, , 3, 47, 4 125, 8, , 4, 52, 4 156, 1, , 4, 58, 6 28, 127, , 4, 62, 6 25, 156, ,5 4, 7, 6 39, 245, , 5, 8, 6 51, 315, , 5, 95, 6 62, 4, 6 11 Weiht Housin: St 52-3, fored Bearin: Steel on steel bearin GE E, requirin maintenance (see pae 78) on request: available with maintenance free Spherical Plain Bearin GE..EC (see pae 7) or in sizes 12, 2, 25, 4, 5, 7, 8, with Spherical Plain Bearin GE LO (see pae 82), requirin maintenance Greasin: up to size 12 without lubrication fittin from size 15-2 fitted with rease hole in housin from size 25 fitted with hydraulic rease nipples to DIN on request: Housin: Stainless steel to from size 1 to 8 available with maintenance free stainless steel Spherical Plain Bearin GE..EC-NIRO (see pae 71) 95

96 Hydraulic Rod Ends - Weld-On Base Series FS...N Rod Ends with rectanular surface for Weld-on. Spherical Plain Bearins, rereasable, fixed with snap rins For Weld-On to cylinder bottoms (D) B M A F L o Pivotin Anle a ( ) , ,5 53, 17, , , 59, 21, , , 65, 21, , , 67, 3, , ,5 69,5 48, , ,5 118, 62, , ,5 196, 8, , , 35, 1, , , 386, 127, , ,5 441, 156, , , 57, 245, , , 724, 315, , , 84, 4, , , 134, 49, , , 1516, 61, , ,5 234, 655, , , 321, 95, Weiht Housin: Bearin: St 52-3, fored Steel on Steel bearin GE E, requirin maintenance Greasin: fitted with hydraulic rease nipple to DIN on request: Housin: Stainless steel to with maintenance free stainless steel Spherical Plain Bearin GE..EC-NIRO (see pae 71) 96

97 Anle Joints Anle Joints to DiN 7182 consistin of ball stud to DIN 7183 and ball journal to DIN 7185 D1 a e d2 d3 Form C d4 Form CS Form C with threaded stud and hexaon nut. l2 l3 SW Form CS with threaded stud, hexaon nut and external clip d (D) a ±,3 d2 d3 ±,5 d4 ±,5 e min l 2 ±,3 l 3 ±,3 SW h14 α 1 ( ) α 2 ( ) Weiht 8 22 M ,8 1,2 1, , M ,8 11,5 12, , M ,3 14, 16, , M , 15,5 2, , M , 15,5 2, , M 14x1,5 22 3, 21,5 28, , M 14x2 22 3, 21,5 28, , Ball Journal: Steel, minimum strenth Rm= 5N/mm 2 Ball Stud: Steel, minimum strenth Rm= 6N/mm 2 Surface: blanc, zinc plated white, on request: yellow or black chromated Alternative: stainless steel to 1.435, Aisi 33 orderin Details: e.. Anle Joint with external clip, Form CS with ball diameter D1 = 1 mm: Anle Joint DiN CS 1 Left Hand Thread: Left hand thread only at the ball journal available: Anle Joint DiN CS 1 LH Loose Fit: increased internal clearance available: Anle Joint DiN CSL 1 97

98 a b d2 a d1 Fork Heads / Fork Ball Joints Fork Heads to DiN Fork Ball Joints to DiN With ES-Bolt (clevis sprin pin) or cotter bolt l4 d1 d1 l1 l2 l3 d3 For use to transmit linear movements b Weiht d1 a d2 d3 l1 l2 l3 l4 B13 H9/h11 ES-Bolt Cotter Bolt Fork Head DiN x , M 4 8 6, 9,2 1,4 4x x , M 5 9 7,5 12, 2,4 5x ,9 13 6x , M 6 1 9, 14,5 4,4 6x , 22 8x , M , 18,7 9,4 8x ,5 54 1x , M , 23,2 17,8 1x , x , M , 28,2 33,6 12x , x , M ,5 31,2 5,7 14x , x , M , 36,2 74,7 16x ,5 41 2x M , 47, 132, 13, 52 Standard Series: free-cuttin steel to 9SMnPb28K, 12L13, tensile strenth 55 to 7 N/mm 2 Surface: zinc plated and chromated, on request: blanc, oiled or phosphated and oiled on request: stainless series, stainless steel to 1.435, Aisi 33 ES-Bolt not in stainless steel available orderin Details: Fork Head: Fork Ball Joint: e.. Form G with bore size d1 = 12mm, split lenth = 24mm: Fork Head DiN G12x24 e.. Fork Ball Joint with Cotter Bolt, with bore size d1 = 12mm, split lenth = 24mm: Fork Ball Joint DiN A12x24 e.. Left Hand Thread: DiN G12x24LH and DiN A12x24LH 98

99 Rubber Seals RERS Rubber Protector Caps made from Neoprene A D B M D1 Protects aainst dust, chemical substances and aressive environment. Resistant to oil, rease, saltwater, chemical components and other substances. Temperature rane from -2 till +12 Celsius or -4 till +248 Fahrenheit. Can be completely filled with rease. Mounted easily with Seeer retainin pliers * Spacers separately on request Rod End Rubber Protector Cap Type Spacers Type* D D1 B M A 6 RERS 1 DR 6 6 8, RERS 1 DR 8 8 1, RERS 2 DR , RERS 2 DR , RERS 3 DR , RERS 3 DR , RERS 3 DR , RERS 4 DR , RERS 4 DR , RERS 4 DR , RERS 5 35 RERS 5 RELS Washer Seals Rubber Seals vulcanized to stainless steel washer rins D M1 D1 A M B Prevents dirt enterin the matin surface. Easily mounted. Temperature resistant up to +11 Celsius or +23 Fahrenheit Rod End / Spherical Plain Bearin size Washer Seal Type D D1 B M M1 A 5 RELS 5 5,25 8,3 2,4,5,8 11,2 6 RELS 6 6,25 9,5 3,1,69,9 12,7 8 RELS 8 8,25 12,4 5,1 1,2 1,4 17,8 1 RELS 1 1,25 13,5 5,6 1,2 1,4 2,3 12 RELS 12 12,25 18,5 6,4 1,2 1,7 28,6 14 RELS 14 14,25 18,5 6,4 1,2 1,7 28,6 16 RELS 16 16,25 22,4 6,8 1,2 1,7 31,7 18 RELS 18 18,25 22,6 8,3 1,2 1,7 32,7 2 RELS 2 2,25 25,2 1,2 1,2 1,7 38,1 25 RELS 25 25,25 33,8 12,7 1,5 2,3 53,3 3 RELS 3 3,25 55,9 14, 1,5 2,3 56,7 99

100 Jam Nuts to DIN 934 / 439 Normal Form DiN 934 / iso 432 Narrow Form DiN 439 / 936 SW SW Jam Nuts with riht or left hand thread. Steel zinc plated or stainless Steel A2 m1 m2 Nominal Thread Pitch M... ISO 432/DIN934 ISO 436/DIN439 SW x,4 x,5 x,7 x,8 x1, x1,25 x1,5 x1,75 x2, x2,5 x3, x4, m1 Weiht m2 Weiht M 3 (M 3x,5) 5,5 X 2,4,4 1,8,3 M 4 (M 4x,7) 7, X 3,2,8 2,2,6 M 5 (M 5x,8) 8, X 4, 1,2 2,7,8 M 6 (M 6x1) 1, X 5, 2,4 3,2 1,5 M 8 (M 8x1,25) 13, X X 6,5 5,1 4, 3,1 M 1 (M1x1,5) 17, X X X 8, 11,1 5, 6,9 M 12 (M 12x1,75) 19, X X X 1, 16,3 6, 9,8 M 14 (M 14x2) 22, X 11, 24, 7, 15, M 16 (M 16x2) 24, X X 13, 32, 8, 19,5 M 18 (M 18x2,5) 27, X 15, 47, 9, 28, M 2 (M 2x2,5) 3, X X 16, 61, 1, 38, M 22 (M22x2,5) 32, X 18, 75, 11, 46, M 24 (M 24x3) 36, X 19, 14, 12, 66, M 27 (M 27x3) 41, X 22, 158, 13,5 96, M 3 (M 3x3,5) 46, X 24, 219, 15, 137, M 36 (M 36x4) 55, X X 29, 37, 18, 23, M 39 (M 39x4) 6, X 31, 47, 19,5 3, M 42 (M 42x4,5) 65, X X 34, 61, 21, 38, M 45 (M 45x4,5 7, X 36, 75, 22,5 47, M 48 (M 48x5) 75, X 38, 91, 24, 58, M 52 (M 52x5) 8, X 42, 113, 26, 7, M 56 (M 56x5,5) 85, X 45, 135, 28, 84, M 64 (M 64x6) 95, X 51, 185, 32, 116, X) available ex stock, Standard Form only with standard thread in stock Thread: Remarks: Standard Thread Pitch steel alvanised, strenth rade: 4 or better, or alternative A2 (which is equivalent to stainless steel 1.431, Aisi 34 and 1.433, Aisi 35) Riht hand or left hand threads Across-flats dimension SW, Weiht, Width m1/m2 and Chamfer can differ from the table above and the DIN, because of different manufacturin methods Jam Nuts DiN 439 accordin to iso 436 (without chamfer) or iso 435 (with chamfer). Jam Nuts DiN 439 Fine Thread accordin to iso 8675 (with chamfer). orderin e.. Jam Nut M 1 Left Hand (Normal Form with standard thread) in stainless steel A2: Details: Jam Nut DiN 934-M1-A2-Left Hand e.. Jam Nut M 39x3 Riht Hand (Narrow Form) in Steel, zinc plated: Jam Nut DiN 439-M39x3-4 1

101 Cylindrical bearins Characteristics: - suitable for dry run with a low friction coefficient - low wear rate - ood slidin properties - suitable for rotatin and oscillatin movements - hih chemical resistance - low absorption of water - work also lubricated Quality: - material thickness PTFE/fiber blend,1 -,3 mm mixed with sintered bronze powder with a thickness of,2 -,35 mm. - Bushin of low-carbon steel: - unusually hih load-bearin capacity - excellent heat conduction - copper-tin coated, coatin thickness 2 μm - has a very ood corrosion resistance Application field: - for a lon durability with or without lubrication - automotive sector, household appliances, conveyor technoloy, ships' enines, hydraulic technoloy, textile industry, machine tools, etc. - Bronze bushin: - unusually hih load-bearin capacity - excellent heat conduction - has a very ood corrosion resistance - Bushin of stainless steel: - has a very ood corrosion resistance Application field: - for a lon durability with or without lubrication - cement delivery pumps, conveyor technoloy, moldin machines, etc. Characteristics: Bushin of steel Bronze bushin max. static load N/mm² max. dynamic load N/mm² 8 8 compressive strenth N/mm² 35 3 max. slidin speed m/s 2 2 friction coefficient μ -,3 bis,8,3 bis,8 temperature rane C -2 bis bis +25 PV max N/mm² x m/s 1,8 1,8 11

102 Cylindrical bearins Series BK1 Cylindrical plain bushin Auskleidun mit einer PTFE/Fasermischun. Wall thickness L / -,4 (D) D f1 f2 min/max ,5,73 X X X 4 5,5,75 X X X 5 7, X X 6 8, X X X 8 1, X X X X X 1 12, X X X X X X 12 14, X X X X X X X,5, ,,98 X X 14 16, 1,5 X X X X X 15 17, X X X X X 16 18, X X X X X 17 19, X X X 18 2, X X X X X 2 23, X X X X X X 22 25, 1,475 X X X X X X,8, , 1,55 X X X X 25 28, X X X X X X X 28 32, X X X X X 3 34, X X X X X X 32 36, 1,97 X X X 1,, , 2,5 X X X X X X X 38 42, X X X 4 44, X X X X X X 12

103 Cylindrical bearins (D) Wall thickness D f1 f2 min/max L / -, , X X X X X 5 55, X X X X X 55 6, X X X X 6 65, 2,46 1,2,8 X X X X X 2, , X X X X X 7 75, X X X X X 75 8, X X X X X X 8 85, X X X X X X 85 9, X X X X 9 95, X X X X X 95 1, 2,44 1,4,8 X X X X 2, , X X X X 15 11, X X X , X X X , X X X , X X X , X X X , X X X , X X X , X X X , X , 2,415 1,4,8 X 2, , X 2 25, X , X , X , X , X 3 35, X Bushin: Recommendation for the assembly: - low-carbon steel lined with a PTFE/fibre mixture/blend - Bronze lined with a PTFE/fibre mixture/blend - Stainless steel lined with a PTFE/fibre mixture/blend - housin bore H7 - shaft diameter f7 - the ap must not be in the load direction 13

104 Cylindrical bearins Series BK1..Bu Cylindrical plain bushin with collar lined with a PTFE/fibre mixture/blend (d) d1 d2 ±,5 L1 -,2 f1 f2 L ±,25 4 5,5 7/7,5 8 9/9,5 11, /16, ,5/ x x x x x x x x x x x x 1,,5, x x x x x x x x x x x x x x x x 1,5,8, x x x x x x x x x 2, 1,, x x x x x x x x 2,5 1,2, x x Bushin: Recommendation for the assembly: - low-carbon steel lined with a PTFE/fibre mixture/blend - Bronze lined with a PTFE/fibre mixture/blend - Stainless steel lined with a PTFE/fibre mixture/blend - housin bore H7 - shaft diameter f7 - the ap must not be in the load direction 14

105 Cylindrical bearins Series BK1-Druckscheibe coated with a PTFE/fibre mixture/blend d +,25 D -,25 T -,5 M ±,125 h +,4/+, , , ,5 3 1, 38 3, , , 65 1, t ±,2 D1 +,12 Disc: - low-carbon steel lined with a PTFE/fibre mixture/blend - bronze lined with a PTFE/fibre mixture/blend - stainless steel lined with a PTFE/fibre mixture/blend 15

106 Bearin block for hydraulic cylinders Series ika.. Bearin block D (H9) B L2 L4 d (h16) L1 (JS14) L3 (JS14) (H13) R F (JS12) , , , , , , , , , , , , , , , , , , , , , , 62 f min. b (A13) load max. () Weiht Housin: spheroidal raphite cast iron EN-GJS 5/7 16

107 Bearin block for hydraulic cylinders Series ikb.. Bearin block D (H9) B L2 d (h16) L1 (js13) L3 L4 (H13) R F (js13) f min , , 3,3 5, , , 3,3 8, , ,5 4,3 12, , ,5 4,3 2, , , 5,4 32, , ,5 5,4 5, , ,5 8,4 8, , , 8,4 125, , , 11,4 2, , , 11,4 32, , ,5 12,4 5, 93 b (A13) S1 (JS14) S2 (N9) S3 (JS14) T (+,3) load max. () Weiht Housin: spheroidal raphite cast iron EN-GJS 5/7 17

108 Bearin block for hydraulic cylinders Series DK.. Bearin block D (K7) B L2 L4 (h14) L1 (js13) L3 (js13) d R F (js11) b +,3/-,1 S1 (js14) , ,3 8, , ,3 12, , ,3 2, , ,4 32, , ,4 5, , ,4 8, , ,4 125, , ,4 2, , ,4 32, , ,4 5, 19 f S2 (N9) T (+,3) load max. () Weiht Housin: spheroidal raphite cast iron EN-GJS 5/7 18

109 D D d Bearin block for hydraulic cylinders - bolt Series KPA../KPB.. L4 L3 M Connectin bolt L2 L1 DIN 471 S1 S2 T 45 LN L2 P for DK L1 KPA: D (h6) d L1 L2 L3 +, , 1, 1,1 12x , 1,5 1,1 16x ,4 1,8 1,3 2x1, ,4 1,8 1,3 25x1, , 2,5 1,6 3x1, ,5 4,2 1,85 4x1, , 5, 2,15 5x , 5, 2,15 6x , 6, 2,65 8x2, , 7, 3,15 1x3 144 L4 M (H13) Circlip Weiht KPB: D (h6) L1 L2 S1 S2 T P LN Weiht ,5 8 3,3 4 1, ,5 8 3,3 4 1, ,5 1 4,5 5 1, ,5 1 4,5 5 1, ,5 13 5,5 6 2, ,5 16 6,5 7 2, , 19 9, 8 2, , 2 9, 9 2, , 26 11, 11 3, , 3 13, 14 3, Bolt: alloyed case-hardened steel 2MnCr5 19

110 D T D D Bearin block for hydraulic cylinders - bolt Series KPE../KPC../KPD.. KPE S1 S2 45 LN Connectin bolt L2 L1 P KPE for version IKA../IKB.. KPC L L KPD KPC and KPD for version IKA../IKB../IF.. with funnel type lubrication nipple DIN DIN KPE: D (m6) L1 L2 S1 S2 T P LN Weiht ,5 8 3,3 3 1, ,5 8 3,3 4 1, ,5 8 3,3 4 1, ,5 1 4,5 5 1, ,5 1 4,5 5 1, ,5 13 5,5 6 2, ,5 16 6,5 7 2, ,5 19 9, 8 2, ,5 2 9, 9 2, , , 11 3, , 28 13, 14 3, 9 15 KPC/KPD: D (f8/m6) L (H16) load max. () Weiht , , , , , , , , , , 76 Bolt: information: alloyed case-hardened steel 2MnCr5 for KPC the tolerance m6 for D and for KPD the tolerance f8 for D 11

111 = = Bearin block for hydraulic cylinders - fixin plate Series PPP... Fixin plate dk DIN B d L2 b L1 Version for KPB../KPE.. L1 L2 B d dk b Threaded bore Circlip Weiht ,4 1/12 3 M5x , M6x , M6x ,4 2 4 M6x , M6x ,4 3 5 M6x ,4 4 6 M8x ,4 5 8 M8x ,5 6 8 M1x ,5 8 1 M1x , M1x Plate: unalloyed structural steel S355JR (St52-3) 111

112 Bearin block for hydraulic cylinders - fork head Series if.. Fork head B1 b R R D f1 f2 F F L2 to ISO 8132 G B2 B2 L1 D (H9) B1 (h16) b F f2 B2 (A13) (js13) f1 min. L1 L M1x1, , M3x M12x1, , M4x M14x1,5 2 12,5 M6x M16x1,5 25 2, M8x M2x1, , M1x M27x2 4 5, M12x M33x2 5 8, M16x M42x , M2x M48x2 71 2, M24x M64x3 9 32, M3x1 36 G (6H) R max. nominal force () screw DiN 912 Weiht Bolt: unalloyed structural steel S355JR (St52-3) 112

113 Bearin block for hydraulic cylinders - connectin pins Series PB.. Connectin pin L1 L L2 L1 B D d2 d1 d3 for version IS../ISS.. D (Ø) d1 (Ø) d3 d2 (Ø) B L L1 L2 Weiht Connectin pin: unalloyed structural steel S355JR (St52-3) 113

114 Bearin block for hydraulic cylinders - bracket Series is.. / iss.. Bracket with with funnel type lubrication nipple DIN DIN d d D L F f F f b T S T S B L2 L1 L2 L1 to ISO 8132 is: D (H7) F (JS12) f L L1 L2 (js13) B b (js13) ,3 9, 8, ,3 11, 12, ,3 11, 2, ,4 13,5 32, ,4 17,5 5, ,4 22, 8, ,4 26, 125, ,4 33, 2, ,4 39, 32, ,4 52, 5, 1 S (N9) T +,3 d (H13) nominal force () Weiht iss: D (H7) F (JS12) f L L1 L2 (js13) B b (js13) ,3 9 8, , , ,3 11 2, , , ,4 18 5, ,4 22 8, , , ,4 33 2, , , ,4 52 5, 112 S (N9) T +,3 d (H13) nominal force () Weiht Bracket: unalloyed structural steel S355JR (St52-3) 114

115 Precision Parts Martin Höhn GmbH Höhn Precision Parts - this name represents quality production. Fourty years of experience uarantee the companies reliable capability. The continuously modernized machine park enables a flexible and economic production of turned and machined parts. Variety for Höhn does mean that besides the turnin, machinin and rindin of parts, also complete components and assemblies are manufactured. In areement with the TÜV Southwest, Höhn received stamp authorization for continued re-stampin of material specification 3.1.B. since Höhn achieved also the DIN EN ISO 91:2 certification. This connectin rod with bearin for carriaes shows a constructive solution throuh the close cooperation between Höhn and FLURO. 5-axial symmetric machinin (3-D measurin machine) Production of all sorts of shafts, Ø 2 to Ø 12 x 1 mm lenth. Surface finish accordin to customer requirements. Höhn processes all sorts of steel e..: Titan, Hasteloy, 17-4Ph, non-iron and non-ferrous heavy metal. Thouh constant stock of stainless steel material such as 1.414, Aisi 43F, 1.431, Aisi 34, 1.435, Aisi 33, , Aisi 316Ti, , Aisi 321 a prompt delivery response is uaranteed. Machinin of the rod from Ø 1 to Ø 8 mm, chuckin parts from Ø 1 to Ø 3 mm. 115

116 1,9 21, 21, 13,7 8, 33,4 1, 21, 8, 33,4 12,5 12,5 12,5 19,7 6, 14,2 8,9 Inquiry Template Special Parts Fax to: +49 () /

117 Notes 117

118 Notes 118

119 Custom-Made Products 119

120 Rosenfeld is situated between the city of Stuttart and the lake Bodensee, in southern Germany. You can et to us easily from the international airport of Stuttart by car. Drive Hihway A81 south (towards Sinen), exit at Oberndorf and follow the road to Rosenfeld. Our company s plant is situated in the midst of an industrial area on the riht hand side behind the town s entrance. We invite you to pay a visit at our manufacturin plant to see our capability. Frankfurt Mannheim Karlsruhe Baden-Baden Heilbronn Stuttart Würzbur Nürnber Ulm München Offenbur Abfahrt Oberndorf/Rosenfeld Ausfahrt 33 Oberndorf Rosenfeld Balinen Tübinen Freibur Rottweil FLURO Sinen Schaffhausen This is how you can et to us. Basel Winterthur Zürich Konstanz Bodensee Siemensstrasse 13 D Rosenfeld / Germany Phone +49 () Fax +49 () info@fluro.de