RT-Dachlichtbänder. RT- Roof Lights

Transcription

1 RT-Dachlichtbänder RT- Roof Lights

2 Advantages quick and easy installation both sides coextrusion possible translucent heat-insulating high temperature resistance versatile designing in shape, colour and function good long term performance through UVresistance 200 x times tougher than glass Polycarbonate doesn t splitter Rodeca roof light systems can be used to gether with Rodeca ventilation flaps as areas for natural smoke and heat ventilati on Applications Roofing and canopies Ventilation Sports and industial buildings Roofing Roof lights - flat and curved Natural smoke and heat release Carports Refurbishments Ceiling covering open areas General information RT Roof lights The Rodeca roof lights are the ideal solution to instroduce natural daylight into large or small interior/exterior covered spaces. These complete systems provide a flexible solution for not only flat or curved applications but also for roofing and canopies of varoius sizes and shape. Combined with its lightweight, high termal properties, impact resistance and ease of installation, the RT-syste,s are an economical daylight solution. List of content Overview RT Roof Lights page 02 System BA-10 page 03 System BA-16 page 04 Head pieces for BA systems page 05 System BFA-10/16 page 06 System BFVA-10/16 page 07 Head pieces for BFA/BFVA Systems page 08 Ventilation flaps/ Natural Heat and Smoke Release device page 09 System FA-10/16/20 page 10 System VFA-10/16/20 page 11 System VSFA-10/16/20 page Overview Rodeca RT roof lights The following table shows an overview about the RT-roof light systems from Rodeca. The specified span widths relate exemplarily to a load of 1kN/m². Should your installation situation not be presented herein, please contact us. We are pleased to develop solutions for your project. BA-10 BA-16 BFA-10/16 BFVA-10/16 FA-10/16/20 VFA-10/16/20 SVFA-10/16/20 curved application R>3,00m curved application R>3,50m curved application R>3,50m curved application R>4,00m pitched application > 5 pitched application > 5 pitched application > 5 < 3.00m* < 3.50m* < 5.50m* < 6.50m* < 2.50m* < 3.50m* < 4.00m* * Recommanded span width for load pressure of 1.00kN/m² Polycarbonate panels Colours Standard: crystal / opal Color version: from 400 m² Colours Standard: crystal / opal Color version: from 400 m² Decocolor version: from 550 m² PC U Colours Standard: crystal / opal Color version: from 400 m² Decocolor version: from 550 m² Gewicht (kg/m²) 3.40 Polycarbonate in general Temperature resistance from -40 to +115 C temporarily up to 130 C 200 x thougher than glass good long term performance through UV protection 10 years warranty against yellowing - ageing - hail stone In many cases RODECA panels are used as meltable area Depending on panel thickness and material composition our Rodeca products are according to DIN 4102 B1 hardly infl ammable or B2 normally fl ammable All installation advices, application requirements and further technical information can be extracted from our technical manuals and installation guides.

3 System BA-10 System BA-16 The system BA-10 is a curved roof light for span widths up to 3.00m.* The glazing is made of 10mm thick Polycarbonate which lock in place into pre-curved aluminium profiles. The roof light is made of prefabricated modules which are connected to each other. The system BA-16 is a curved roof light for span widths up to 3.50m.* The glazing is made of 16mm thick Polycarbonate which lock in place into pre-curved aluminium profiles. The system gasket offers addtional heat insulation. The roof light is made of prefabricated modules which are connected to each other. Interlocking glazing bar (part A) Item no.: Interlocking glazing bar (part B) Item no.: Interlocking glazing bar (part A) Item no.: Interlocking glazing bar (part B) Item no.: System gasket Item no.: Drip profile Item no.: Drip profi le Item no.: Cover plate Item no.: 59w Cover plate Item no.: 59w Sealing band 30*5 Item no.: Sealing band 30*5 Item no.: * Recommended span width for load pressure of 1.00kN/m² * Recommended span width for load pressure of 1.00kN/m² 3 4 6

4 Head pieces for the systems BA-10 / BA-16 System BFA-10 / BFA-16 The head pieces of the systems BA-10 and BA-16 are made of 16mm thick Multi Wall Sheets framed in aluminium profiles. The system BFA-10 respectively BFA-16 is a curved roof light for span width up to 5.50m.* The glazing consist of optionally 10mm or 16mm thick Polycarbonate U-panels, locked into pre-fabricated aluminium profi les. The load bearing construction of the BFA roof light are aluminium glazing bars supported on fxing shoes. Cover profi le with gaslet bar Item no.: Base profi le Side profi le Item no.: 59v40303 Frame profi le Item no.: 59u Frame profile Item no.: Gasket Item no.: Item no..: End profi le Item no.: for 10mm Item no.: for 16mm Drip profile Item no: for 10mm Item no.: for 16mm Item no.: 59w30202 Item no.: MWS 16-5 Weight (kg/m²) Weightt (kg/m²) 3.20 *Recommended span width for load pressure of 1.00kN/m²

5 System BFVA-10 / BFVA-16 Head pieces for systems BFA / BFVA Zubehör The system BFVA-10 respectively BFVA-16 is a bended roof light for span width up to 6.50m.* The glazing optionally is made of 10mm or 16mm thick Polycarbonate U- Panels, which lock in place into previously bended aluminium profiles, through a clip connection. The load bearing construction of the BFVA roof light is made of reinvorced aluminium mullions framed in fixing shoes. The head pieces of the systems BFA-10 / BFA -16 as well as for the systems BFVA-10/ BFVA-16 are made of 16mm thick Multi wall sheets framed in aluminium profiles. Closure angle Item no.: 59w40302 bar Item no.: Frame profi le Item no.: 59u Frame profile Item no.: Base profi le Side profi le Item no.: 59v60403 Gasket Item no.: for 10&16mm panels Side profi le Item no.: 59v60403 bzw. Item no.: 59v40303 End profi le Item no.: mm panel Item no.: mm panel Drip profi le Item no.: mm panel Item no.: mm panel Item no.: upon request Item no.: * Recommended span width for load pressure of 1.00kN/m² 7 8 MWS 16-5 Weight (kg/m²) 2.80

6 Ventilation flaps Suitable for all curved Rodeca roof lights Version half module vent Maximum dimensions: depending on loads - prior consultation necessary Version Full module vent Maximum dimensions: depending on loads - prior consultation necessary Drive with 230V spindle actuator optionally 300mm or 500mm hub with 10mm, 16mm or 20mm thick Ventilation fl aps / Natural Smoke and Heat Exhaust device for systems BA-10 / BA-16 / BFA-10 / BFA-16 / BFVA-10 / BFVA-16 Rodeca ventilation fl aps as well as natural smoke and heat release devices are customized to the length, width and radius of the chosen roof light. The glazing can be optional with 10mm,16mm or 20mm panels. half module vent Systems FA-10 / FA-16 / FA-20 The systems FA-10, FA-16 respectively FA-20 are roof lights for pitched usage from 3 and for span width up to 2.50m.* The glazing is made optionally of 10mm, 16mm or 20mm thick Polycarbonate, which lock into aluminium profi les. The load bearing construction of the FA roof lights is made of aluminium glazing bars on fxing shoes. bar Item no.: Base profi le Side profile Item no: 59v40303 NSHEV Suitable for all curved Rodeca roof lights Approved and certified according to DIN EN : Version half module vent Maximum dimensions: Width: 2.40m, length: 1.70m Maximum aerodynamic area: 2.45m² Version full module vent maximum dimensions: Width: 2.40 m length: 1.70 m Maximum aerodynamic area: 2.65m² Drive via thermal pneumatic release device Ventilation drive with 24V spindle actuator optionally 300mm or 500mm hub with 10mm, 16mm or 20mm MWS 10-4 Weight (kg/m²) 1.75 MWS 16-5 Weight (kg/m²) 2.80 MWS 20-5 Weight (kg/m²) 3.10 full module vent PC U Weight (kg/m²) 3.40 * Recommended span width for load pressure of 1.00kN/m² Gasket Item no.: &16mm panel Item no.: mm panel End profile Item no.: mm panel Item no.: mm panel Item no.: mm panel Drip profile Item no.: mm panel Item no.: mm panel Item no.: mm panel Item no.: 59w30202 Item no.:

7 System VFA-10 / VFA-16 / VFA-20 System VSFA-10 / VSFA-16 / VSFA-20 The systems VFA-10, VFA-16 respectively VFA-20 are roof lights for pitched usage from 3 and span widths up to 3.50m.* The glazing is made optionally of 10mm,16mm or 20mm thick Polycarbonate which lock into aluminium profiles. The load bearing construction of the VFA roof light is made of reinvorced aluminium glazing bars supported on fixing shoes. The systems VSFA-10, VSFA-16 respectively VSFA-20 are roof lights for pitched usage from 3 and span widths up to 4.00m.* The glazing is made optionally of 10mm,16mm or 20mm thick Polycarbonate which lock into aluminium profi les. The load bearing construction of the VSFA roof light is made of reinvorced aluminium glazing bars supported on fixing shoes. bar Item no.: bar Item no.: Base profile Side profi le Item no.: 59v60403 Base profi le Side profile Item no.: 59v60403 Gasket Item no.: &16mm panel mm panel Item no.: 59w50252 Item no.: Cover profi le Buliding width (mm) 600 (+1/-1%) End profile Item no.: mm panel Item no.: mm panel Item no.: mm panel Sealiung band 20*4 End profi le Item no.: mm panel Item no.: mm panel Item no.: mm panel 6 6 Buliding width (mm) 630 (+1/-1%) Drip profi le Item no.: mm panel Item no.: mm panel Item no.: mm panel Item no.: 59w50252 Item no.: PC U Buliding width (mm) 630 (+1/-1%) Weight(kg/m²) 3.40 * Recommended span width for load pressure of 1.00kN/m² PC U Weight (kg/m²) 3.40 * Recommended span width for load pressure of 1.00kN/m² Drip profile Item no.: mm panel Item no.: mm panel Item no.: mm panel

8 Qualität made in Germany planen Sie mit uns RODECA überzeugt seit über 40 Jahren mit Innovation und Erfahrung. Unsere vielfältig einsetzbaren, transparenten Bauelemente aus Polycarbonat sorgen weltweit für Aufsehen, zahlreiche Architekturpreise und Auszeichnungen belegen unsere Philosophie. Planen Sie mit RODECA die Fassaden von morgen. Quality made in Germany Design with RODECA RODECA is the market leader in innovation and design with more than 40 years experience in the manufacture of translucent materials. Our architectural award winning, transparent polycarbonate building elements are recognised worldwide, demonstrating our philosophy. Design with RODECA the facades of tomorrow. Fon +49 (0) Fax +49 (0) The RODECA product groups overview / Die RODECA Produktgruppen im Überblick: Roof Lights RT-Dachlichtbänder Fon +49 (0) Fax +49 (0) info@rodeca.de