KRONE - Profi Liner. Quantity: 2 Type: SDP 27 elp3-cs. Technical specification/description

Transcription

1 KRONE - Profi Liner Quantity: 2 Type: SDP 27 elp3-cs Technical specification/description FIN-registration (Finland) Without country symbol sticker Lettering on manufacturers plate: Type: SD National type approval: e24*nks*0077 without specifying the national registered masses on the manufacturers plate Max registered king pin load: kg Max registered Axle load: kg Allowable gross vehicle weight: kg Max technical tow bar load: kg Max practical axle load kg Max practical allowable gross vehicle weight: kg Net weight (+/- 3 %) : 7177 kg Suitable for towing vehicle according to ISO th wheel height unloaded: mm Chassis Supporting legs Double T-longitudinal beams and cross members including side rave with cross members and extensions all fully welded construction Reinforced by additional cross members Award winning Multilock side rave including load securing positions every 100 mm Neck height: 100 mm (including floor and saddle plate) 2" King pin (corner dimension: mm) For load area length: mm For load area width: mm Rear bumper according to EC-regulation Side guard 10 pairs of post pockets 81 x 81 mm in side rave and 10 post pockets 81 x 81 mm centrally positioned in the floor Note: Post pockets / plug in posts not designed for the sole cargo securing 4 pairs of ferry shackles according to PREN Advice: Ferry shackles at rear have restricted usage Pull out ladder at rear Door catch 2 mechanically operated landing legs, 2 x 12 tons capacity, semicircular with base plate, Brand: Krone-choice Landing legs operated from right side Length from kingpin centre to landing legs centre: mm Axles/Suspension 3 axles each with a load capacity of kg Distance from kingpin to centre of axle unit = mm Wheel base: / mm SAF axles, Intradisc, with air suspension and disc brakes, Offset 120 Disc brakes 430 mm

2 With raise and lower valve, including auto reset valve, in lowering position with fixed position Lift axle control for 1st axle Including hand pneumatic lower valve for lifting axle ( = starting aid according to Directive 97/27 / EG ) Preparation of the Lift/trailing axle(s) for the operation through tractor unit (without tractor unit installation), according to selected plug connector(s) for light, for control via *Contact 6 of 7-pin additional plug connector - ISO 3731 and/or *Contact 12 of 15-pin plug connector - ISO and/or *Contact 8 A of VBG plug connector Note: Trailer is not able to turn round ''BO circle'' when 1st axle is lifted. The lift axle is only to be used as Traction assistance in accordance with guideline 97/27/EG Tyres (rims) 6 x 385/65 R 22.5, Premium tyre Krone choice (from a European or Japanese production) Without spare wheel Spare wheel carrier Spare wheel holder as fixed basket for one spare wheel, right side, behind axles Mud guards Brakes Light Wheel covering according to EC-regulations Spray suppression according to EC guideline Brake system according to ECE R 13 (incl. stability system) Spring parking brake Diagnostics by ISO7638 plug connection (EBS supply cable) Brake air pipes, approx. 800 mm above platform level 2 wheel chocks Standard ISO 1728 coupling (Palm) Additional Duomatic coupling for air system Braking system, brand: Wabco Attention: The trailer is only allowed on towing vehicles with compatible braking systems! EBS-braking system, 2S/2M, 2 sensors on 1 axle Lights according to UN ECE Regulation No number plate lights (LED) 2 LED outline marking lights with rubber-arm LED Side marker lights Electric-cable connection at front, approximately 300 mm above platform 24 volt, at front, with 7-channel power socket DIN ISO channel-power socket DIN ISO 3731 at front, for add.uses Additional 15-channel-power socket at front; DIN ISO Multi functional rear lights, brand: Hella Including 1 fog light

3 Including 1 reverse light Accessories Floor Roof frame Front wall Rear wall Trapezium shaped steel buffers at rear Delta shaped rubber impact profile section across rear frame 2 warning plates ECE-R70 (r./y.), 565x200 mm, on rear bumper 4 Chain adaptor (pair) for Multilock side rave, each for max. 4 to. drag Type: BO B 30 mm thick, phenolic coated plywood floor, sectioned area fully waterproofed and sectional areas sealed. Resistance according to DIN EN 283; for floor loadings up to kg forklift axle load. Premium floor sealing Chequered steel plate, at rear, in-ground (4x450mm) Type: AB AP, dimensions:13620 mm inside length x inside width Aluminium cant rail, continuous, for support of sliding curtain and sliding posts EDSCHA sliding roof (175) with plastic joints, height 175 mm, gradient 0 mm, suitable for transport of mesh containers according to DIN Side access height, floor to cant rail at front: mm Side access height, floor to cant rail at rear: mm Internal height with closed roof: mm Rear access height (through rear frame): mm Total height (unloaded) approx mm Lifting roof, hydraulic, liftable up to 500 mm at 4 corner posts separately Adjustable driving height, front, lowering device from basic position 150 mm (in 50 mm steps), reduced lift: 350 mm Adjustable driving height, rear, lowering device from basic position 100 mm (in 50 mm steps), reduced lift: 400 mm Note: Lifting roof completely lowered for pick up Rubber lip seal at cant rail: grey Roof also movable to rear (roof curtain fixable to front roof cover and if necessary diagonal tension has to be released before moving) Diagonal roof spanning 4 Set(s) of wooden planks (96x25 mm) Steel front wall with bolted corner posts Front wall inner reinforced with plywood Holder for curtain cord at front wall Delta shaped profile at the Coupling bearing Quick release for side curtains on front wall Steel container rear doors including bolted steel frame, integrated door locks and concealed door hinges; roof traverse hinged and movable Loading width at rear doors mm Rear wall painted

4 Door locks with 1 hand operation, with fixing for part opened door Double door locks for container rear door Curtain clamping device at rear frame with ratchet Fixing of tensioning pole (sliding roof) on rear wall Drop sides Posts (stakes) Accessories Curtain TÜV-Approval Painting Without drop sides 3 pairs of KRONE side posts, positioned opposite each other symmetrically, with 6 different mounting positions on each side of the chassis, Loading width between side posts mm Plank pockets for stanchions: 1 set on floor level suitable for 4 sets of planks 5 sets of plank pockets in stanchions Without customs seal 1 Sticker 'Load security certified' (EN XL) 1 PVC curtain, with full lengths vertical reinforcements, top with rollers for sliding, bottom with tensioners, materialquality 850 gr./m² Over centre curtain buckle made from stainless steel Curtain provided for sliding roof Roof curtain white Roof curtain ADR, DIN in 680 gr. design Curtain pole strap with integrated grip handle White, part outline markings according to ECE-R48, on both sides of curtain reflective outline marking on rear wall, ECE-R48 yellow Approval of the certificate of conformity according to Annex IX of Directive 2007/46/EC based on a national type approval: e24*nks*0077*02 incl. Finland- - Registration Load security certificate according EN Code XL Attention: by pick up of trailer please note the vehicle's total height. We have special att. to the following points: 1) The common carrier is in authority for damages. 2) For the transfer of the vehicles, we assume no liability. 3) The carrier must seek self-about a permit under 29 of Road Traffic Regulations. Type: paint S Steel parts are shot blasted, KTL-primer coated and powder coated Due to different production sites slight color differences of attachments occur. 1. Color group Vehicles: 2 Vehicles

5 Chassis including side rave Axles including hub Attachment parts Upper structure (front wall/rear portal/rear wall) Rims Side guards Rear bumper Light panel Side posts (Curtain sider) Landing legs Ferry shackles Curtain colour: BLACK OR GALVANIZED RAL 7035 LIGHT GREY SILVER NATURE KTL PRIMER COATED RAL 1004 GOLDEN YELLOW SIOEN 7179 SIGNAL GREY