Drive selection Technical data DC permanent magnet motors

Size: px

Start display at page:

Download "Drive selection Technical data DC permanent magnet motors"

Chloe Bates
5 years ago
Views:

Technical data DC permanent magnet motors Description DC permanent magnet motors have a torque-speed characteristic with shunt characteristics.

The magnetic flux necessary to generate the torque is produced by permanent magnets. A special field excitation winding and thus an element that would cause additional heat loss is not required.

1 Technical data DC permanent magnet motors Description DC permanent magnet motors have a torque-speed characteristic with shunt characteristics. Thanks to a particular dimensioning of the armature winding (copper filling factor) there is only a low speed reduction under load. The magnetic flux necessary to generate the torque is produced by permanent magnets. A special field excitation winding and thus an element that would cause additional heat loss is not required. This means that the efficiency of a DC permanent magnet motor is better than the efficiency of a comparable fieldwound DC motor. As permanent magnets are smaller than a comparable field winding, a DC permanent magnet motor is approximately one frame size smaller than a fieldwound DC motor with the same rated power. General data DC permanent magnet motor Motor type 13.1ò.òò.ò.ò.ò Enclosure IP54 Thermal class (VDE 530) F Motor protection Thermal contact (normally-closed contact) Cooling naturally ventilated Temperature range 0 to +40 C Site altitude Up to 1000 m a.m.s.l. Electrical connection Cable / terminal box Note options in the tables Bearing Deep-groove ball bearing Operating mode (VDE 530) S1 Rated data Motor type Rated power (W) Rated torque (Nm) Rated armature voltage (V) Rated current (A) Max. demagnetisation current (A) Armature resistance (Ω) Armature inductance (mh) Rated speed (rpm ) Moment of inertia (kgcm ) Max. radial force (N) F r Max. axial force (N) F a Small drives en 3/005

2 Technical data DC permanent magnet motors Characteristics M n = Nm n n = 3000 rpm M n = 0.35 Nm n n = 3000 rpm T [K] n/n n I/I n T [K] M/M n M/M n M n = Nm n n = 3000 rpm M n = 1.18 Nm n n = 3000 rpm T [K] n/n n I/I n T [K] n/n n I/I n n/n n I/I n M/M n M/M n M n = 1.91 Nm T [K] n n = 3000 rpm n/n n I/I n Explanations 1: Armature current (mean value) as function of torque : Speed as function of torque at rated voltage 3: Housing temperature increase as function of torque at F F = 1 for 160 V and 180 V motors 4: As 3, for 4 V motors M/M n, I/I n, n/n n : standardised values referred to the rated value For a detailed dimensioning of the drives please consult your Lenze sales representative. M/M n Small drives en 3/005-11

3 DC permanent magnet motors Selection table Type òò.ò.ò.ò Motor type P N U n M Design Selection W V rpm Nm A-side (tick as required) or B B ò or B ò IEC56 B14C ò B ò 00 4 or IEC56 B ò IEC56 B14C ò IEC63 B14C ò or IEC63 B ò IEC63 B14C ò IEC63 B14C ò IEC71 B14C ò IEC71 B ò IEC71 B14C ò IEC71 B ò IEC71 B14C105 Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake frame size only 4 = with DC tacho frame size only 5 = with AC tacho frame size only 6 = for tacho attachment frame size only 7 = for brake attachment frame size only Rated armature voltage 4 V 160 V frame size 75 only 180 V frame size only Brake supply voltage 4 V DC 05 V DC only with armature voltage of 160 V or 180 V Electrical connection Cable Terminal box with motor frame size only Position of electrical connection B Position of electrical connection B14 Type code see pages 1-3 to 1-6. Mounting position see cover fold-out. -1 Small drives en 3/005

4 DC permanent magnet motors Selection table Type 13.1ò.òò.ò.ò.ò Motor type P N U n M Design Selection W V rpm Nm A-side (tick as required) for gearbox attachment or B14 for SPL B14 for SSN B3/B14 for SSN ò or B14 for SSN ò B3/B14 for SSN ò 00 4 or B14 for SSN ò B3/B14 for SSN ò or B14 for SSN ò B3/B14 for SSN ò B14 for SSN ò B3/B14 for SSN ò B14 for SSN ò B3/B14 for SSN40 Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake frame size only 4 = with DC tacho frame size only 5 = with AC tacho frame size only 6 = for tacho attachment frame size only 7 = for brake attachment frame size only Rated armature voltage 4 V 160 V frame size 75 only 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 160 V or 180 V Electrical connection Cable Terminal box (not frame size 35) Position of electrical connection B3/B Position of electrical connection B14 Small drives en 3/005-13

5 DC permanent magnet motors Dimensions Type òò.ò.ò.ò B3 B14 No terminal box with frame size Small drives en 3/005

6 DC permanent magnet motors Dimensions Type òò.ò.ò.ò Motor type Frame size a a 1 a 3 b b 1 c c 1 d e 1 j7 B ò h6 B B ò.ò.ò B h6 45 IEC56 B14C k6 65 IEC56 B k6 IEC56 B14C ò.ò.ò 115 IEC63 B14C k6 IEC63 B14C IEC63 B IEC63 B14C k ò.ò.ò 140 IEC63 B14C IEC71 B14C k6 85 IEC71 B ò.ò.ò k6 IEC71 B14C Motor type f f 1 g g 1 g h i k l*) l 1 l m n p s s 1 t u w 1 Weight max. approx. kg ò ò.ò.ò ò.ò.ò ò.ò.ò ò.ò.ò M M M M M M M M M M6 10. *) Motors / 45 do not have a shaft collar. Dimensions in mm Small drives en 3/005-15

7 DC worm geared motors Selection table Type SSN5-1PVCò-035C1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò Additional order information Motor type = B14 5 = B3/B14 Rated armature voltage 4 V 180 V Electrical connection Cable Gearbox type VCR VCL DCR Shaft position on type VCR 3 5 Flange/shaft position on type VCL 3 5 Mounting position A B C D E F Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out. -16 Small drives en 3/005

8 DC worm geared motors Dimensions Type SSN5-1PVCò-035C1 Geared motor a a 1 b b 1 b c c 1 d e e 1 f f 1 f g g 1 g h h 1 B3 B14 B3 B14 B3 B3 B14 B3 B14 B3 B14 B3 B3 B3 ø j7 h11 h6 ø SSN5-1PVCò-035C Geared motor i k k 1 l 1 l l 3 l 4 n q q 1 q q 3 s s 1 t u Weight B3 B3 B14 B3 B14 B3 B3 B14 B3 B14 B3 B14 approx. kg SSN5-1PVCò-035C M Dimensions in mm Small drives en 3/005-17

9 DC worm geared motors Selection table Type SSN31-1Pòòò-045C1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò.ò Additional order information Motor type = B14 5 = B3/B14 B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage: 4 V 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 180 V Electrical connection Cable Terminal box Gearbox type VAR Shaft D = 10x30 mm Shaft D = 1x40 mm DAR Shaft D = 10x30 mm Shaft D = 1x40 mm VAL Shaft D = 10x30 mm Flange D = 100 mm Shaft D = 1x40 mm Flange D = 10 mm HAR Shaft position on gearbox type VAR 3 5 Flange/shaft position on gearbox type VAL 3 5 Mounting position A B C D E F Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out. -18 Small drives en 3/005

10 DC worm geared motors Dimensions Type SSN31-1PVAò-045C1 VAR DAR VAL Geared motor a b b 1 b c c 1 d e e 3 f f 1 f g h h 1 i j7 h8 h6 SSN31-1PVAò-045C Geared motor k k 1 k l 1 l l 3 l 4 q 1 q q 3 q 4 s s s 4 t u Weight approx. kg SSN31-1PVAò-045C1 Dimensions in mm M6 M M6 M Small drives en 3/005-19

11 DC worm geared motors Dimensions Type SSN31-1PHAR-045C1 Geared motor a 1 a 5 a 6 a 7 b 1 b 5 b 6 b 7 c 5 d d 1 e 1 e 4 e 5 f 1 f 5 f 6 g h8 H7 SSN31-1PHAR-045C Geared motor h h 1 i k k 1 k l m n 1 n q s 1 s 4 s 5 s 6 t u Weight approx. kg SSN31-1PHAR-045C M Dimensions in mm -130 Small drives en 3/005

12 DC worm geared motors Selection table Type SSN31-1Pòòò-056C1 KMAT Motor type P N n M c i Selection W rpm Nm (tick as required) ò.ò Additional order information Motor type = B14 5 = B3/B14 B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage: 4 V 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 180 V Electrical connection Cable Terminal box Gearbox type VAR Shaft D = 10x30 mm Shaft D = 1x40 mm DAR Shaft D = 10x30 mm Shaft D = 1x40 mm VAL Shaft D = 10x30 mm Flange D = 100 mm Shaft D = 1x40 mm Flange D = 10 mm HAR Shaft position on gearbox type VAR 3 5 Flange/shaft position on gearbox type VAL 3 5 Mounting position A B C D E F Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out. -13 Small drives en 3/005

13 DC worm geared motors Dimensions Type SSN31-1PVAò-056C1 Geared motor a b b 1 b c c 1 d e e 3 f f 1 f g h h 1 i j7 h8 h6 SSN31-1PVAò-056C Geared motor k k 1 k l 1 l l 3 l 4 q 1 q q 3 q 4 s s s 4 t u Weight approx. kg SSN31-1PVAò-056C1 Dimensions in mm M6 M M6 M Small drives en 3/

14 DC worm geared motors Dimensions Type SSN31-1PHAR-056C1 Geared motor a 1 a 5 a 6 a 7 b 1 b 5 b 6 b 7 c 5 d d 1 e 1 e 4 e 5 f 1 f 5 f 6 g h8 H7 SSN31-1PHAR-056C Geared motor h h 1 i k k 1 k l m n 1 n q s 1 s 4 s 5 s 6 t u Weight approx. kg SSN31-1PHAR-056C M Dimensions in mm -134 Small drives en 3/005

15 DC worm geared motors Selection table Type SSN40-1Pòòò-063C1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò.ò Additional order information Motor type = B14 5 = B3/B14 B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage: 4 V 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 180 V Electrical connection Cable Terminal box Gearbox type VAR DAR VAL HAR Shaft position on gearbox type VAR 3 5 Flange/shaft position on gearbox type VAL 3 5 Mounting position A B C D E F Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

16 DC worm geared motors Dimensions Type SSN40-1PVAò-063C1 Geared motor a a a 3 b b 1 b c c 1 d e e 3 e 6 f f 1 f g g 1 g h 1 h j7 h10 h6 SSN40-1PVAò-063C Geared motor i k k 1 k l 1 l m 1 n q 1 q q 3 q 4 s s s 3 t u Weight approx. kg SSN40-1PVAò-063C M8 M Dimensions in mm Small drives en 3/

17 DC worm geared motors Dimensions Type SSN40-1PHAR-063C1 Geared motor a 1 a 5 a 6 a 7 b 1 b 5 b 6 b 7 c 5 d d 1 e 1 e 4 e 5 f 1 f 5 f 6 g g 1 g h8 H7 SSN40-1PHAR-063C Geared motor h h 1 i k k 1 k l m n 1 n p q s 1 s 4 s 5 s 6 t u Weight approx. kg SSN40-1PHAR-063C M Dimensions in mm -138 Small drives en 3/005

18 DC worm geared motors Selection table Type SSN40-1Pòòò-071C1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò.ò V ò.ò V Additional order information Motor type = B14 5 = B3/B14 B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage: 4 V 160 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 160 V Electrical connection Cable Terminal box Gearbox type VAR DAR VAL HAR Shaft position on gearbox type VAR 3 5 Flange/shaft position on gearbox type VAL 3 5 Mounting position A B C D E F Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

19 DC worm geared motors Dimensions Type SSN40-1PVAò-071C1 VAR DAR VAL Geared motor a a a 3 b b 1 b c c 1 d e e 3 e 6 f f 1 f g g 1 g h 1 h j7 h10 h6 SSN40-1PVAò-071C Geared motor i k k 1 k l 1 l m 1 n q 1 q q 3 q 4 s s s 3 t u Weight approx. kg SSN5-1PVCò-071C M8 M Dimensions in mm Small drives en 3/

20 DC worm geared motors Dimensions Type SSN40-1PHAR-071C1 Geared motor a 1 a 5 a 6 a 7 b 1 b 5 b 6 b 7 c 5 d d 1 e 1 e 4 e 5 f 1 f 5 f 6 g g 1 g h8 H7 SSN40-1PHAR-071C Geared motor h h 1 i k k 1 k l m n 1 n p q s 1 s 4 s 5 s 6 t u Weight approx. kg SSN40-1PHAR-071C M Dimensions in mm -14 Small drives en 3/005

21 DC planetary geared motors Selection table Type SPL4-òPVCR-035C1 Motor type P N n M c i Selection W rpm Nm (tick as required) Additional order information Rated armature voltage: 4 V 180 V Electrical connection Cable Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

22 DC planetary geared motors Dimensions Type SPL4-òPVCR-035C1 Geared motor Ratio b 1 d d e 1 f 1 g g 1 g g 3 i 1 k 1 k 3 l l 1 l s 1 t u Weight i h10 g6 approx. kg SPL4-òPVCR-035C M M x Dimensions in mm Small drives en 3/

23 DC planetary geared motors Selection table Type SPL5-òPVCR-045C1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage 4 V 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 180 V Electrical connection Cable Terminal box Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

24 DC planetary geared motors Dimensions Type SPL5-òPVCR-045N1 Geared motor Ratio b 1 d d e 1 f 1 g g 1 g g 3 i 1 k 1 k 3 l l 1 l s 1 t u Weight i h8 h7 approx. kg SPL5-òPVCR-045N M M x Dimensions in mm Small drives en 3/

25 DC planetary geared motors Selection table Type SPL6-òPVCR-056N1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò Selection table Type SPL81-òPVCR-063N1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage 4 V 180 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 180 V Electrical connection Cable Terminal box Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

26 DC planetary geared motors Dimensions Type SPL[6 81]-òPVCR-[ ]N1 Geared motor Ratio b 1 d d e 1 f 1 g g 1 g g 3 i 1 k 1 k 3 l l 1 l s 1 t u Weight i j7 h7 approx. kg SPL6-òPVCR-056N M M x SPL81-òPVCR-063N M M x Dimensions in mm Small drives en 3/

27 DC planetary geared motors Selection table Type SPL81-òPVCR-071N1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò V ò V Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage 4 V 160 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 160 V Electrical connection Cable Terminal box Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out Small drives en 3/005

28 DC planetary geared motors Dimensions Type SPL81-òPVCR-071N1 Geared motor Ratio b 1 d d e 1 f 1 g g 1 g g 3 i 1 k 1 k 3 l l 1 l s 1 t u Weight i h8 h7 approx. kg SPL81-òPVCR-071N M M x Dimensions in mm Small drives en 3/

29 DC planetary geared motors Selection table Type SPL1-òPVCR-071N1 Motor type P N n M c i Selection W rpm Nm (tick as required) ò V ò V Additional order information B-side design 0 = no built-on accessories 1 = with spring-applied brake 4 = with DC tacho 5 = with AC tacho 6 = for tacho attachment 7 = for brake attachment Rated armature voltage 4 V 160 V Brake supply voltage 4 V DC 05 V DC only with armature voltage of 160 V Electrical connection Cable Terminal box Position of electrical connection Type code see pages 1-3 to 1-6. Mounting position see cover fold-out. -15 Small drives en 3/005

30 DC planetary geared motors Dimensions Type SPL1-òPVCR-071N1 alternative Geared motor Ratio b 1 d d e 1 f 1 g g 1 g 3 i 1 k 1 k 3 l l 1 l s 1 t u Weight i j7 k6 approx. kg SPL1-òPVCR-071N1 3.7; M M x Dimensions in mm Small drives en 3/

Lenze. Small drives The product range. Meyer Industrie-Electronic GmbH MEYLE Carl-Bosch-Straße Lengerich/Germany

Lenze. Small drives The product range. Meyer Industrie-Electronic GmbH MEYLE Carl-Bosch-Straße Lengerich/Germany 453 778 Small drives The product range Meyer Industrie-Electronic GmbH MEYLE Carl-Bosch-Straße 8 49525 Lengerich/Germany Tel.: +49 (0) 5481-9385-0 Fax: +49 (0) 5481-9385-12 Internet: www.meyle.de E-Mail: